Iphone 4 wont turn on or connect to computer

Please help me,
My iphone 4 will not charge, its just a black screen - wont reset by holding middle button and top botton on fone - will not connect to the computer at all please help me

While connected to the iPhone charger, try to reset the iPhone. Press and hold the Sleep/Wake button and the Home button at the same time for at least ten seconds, until either the Apple logo or battery symbol appears. If the battery symbol appears, continue to charge iPhone until it is fully charged.

Similar Messages

  • My new iphone 4 wont turn on/charge/ connect to computer

    Today I went to Disneyland with some friends. My phone died earlier in tha day. When I got home I plugged it in to charge it and it charged up to about 15%. Then It randomly just turned off. I tried reboot it and everything. I know its not dead becuase its been on the charger forever! I read that I should restore it but when I plug it into the computer it doesnt reconize it!! Then i tried to recovery mode too. It wont even let me do that! HELP PLEASE

    While connected to the iPhone charger, try to reset the iPhone. Press and hold the Sleep/Wake button and the Home button at the same time for at least ten seconds, until either the Apple logo or battery symbol appears. If the battery symbol appears, continue to charge iPhone until it is fully charged.

  • HT1174 my ipod wont work and wont turn on or connect to computer its just like the whole device has been totally erased what do i do?

    okay so yesterday i tried doing something to my ipod now it wont turn on or connect to the computer and its like the whole software on it is totally erased and its 4 years old and has one chip in it and a broken home button what can i do? or how can i fix this? is it cheaper to just go buy a brand new ipod?

    Try:                                               
    - iOS: Not responding or does not turn on           
    - Also try DFU mode after try recovery mode
    How to put iPod touch / iPhone into DFU mode « Karthik's scribblings
    - If not successful and you can't fully turn the iOS device fully off, let the battery fully drain. After charging for an least an hour try the above again.
    - Try another cable                                                       
    - Try on another computer                                                       
    - If still not successful that usually indicates a hardware problem and an appointment at the Genius Bar of an Apple store is in order.
    Apple Retail Store - Genius Bar                                     

  • Ipod wont turn on or connect to computer after reset while restoreing

    so i was restoreing my ipod and i realized there was some pics i wanted so i disconnected the ipod and then reset doing the thing where u hold select and menu and now it wont turn on or connect to the computer please help me out

    bump

  • IPod Touch 2G 8GB wont turn on or connect to computer. Device Malfunctioned

    My iPod Touch 2G 8GB will not turn on or connect to my (or any other) computer or accesory. I'm not sure but I believe my USB cord may have been damp from a recent flood.
    When I plug it into a Vista computer, a popup reads "One of the usb devices attached to this computer has malfunctioned and windows does not recognize it"
    Do you have any idea what might have happened? I'm not positive the cord was damp, but if it was, does anyone know what it could have done to my ipod and is it salvageable?
    I tried the standard home/power reset and tried plugging it into various accessories (car stereo, alarm clock dock) but nothing worked. THe screen is just black and hasnt changed at all.
    If anyone can offer any input, I would greatly appreciate it.
    Thanks

    bump

  • I pod 5th generation wont turn on or connect to computer.

    My ipod 5th generation with the latest update suddenly stopped working over night. It will not power on or connect to the computer what so ever. There is no physical damage at all that would indicate fall damage what so ever. I went to bead last night after using it and at the time it had no problems, however after i woke up and went to go check it nothing would work. It looked as if it was powered off. I could not turn it on with the on button, nor by plugging it in. I then connected it to the computer with about 5 differient chargers that all work on my brothers ipod and the computer could not detect my ipod but had no problem my brothers. It is also a replacement ipod from apple because my first ipod the battery just couldent hold a charge so they replaced it free of cost, However i do believe that it was referbished and not a brand new one if that has anything to do with this problem. What i want to know is can i fix it on my own? is it physical or has programing failed on it? And if i cant fix it what can i do?

    Try:                                               
    - iOS: Not responding or does not turn on           
    - Also try DFU mode after try recovery mode
    How to put iPod touch / iPhone into DFU mode « Karthik's scribblings
    - If not successful and you can't fully turn the iOS device fully off, let the battery fully drain. After charging for an least an hour try the above again.
    - Try another cable              
    - Try on another computer                                                       
    - If still not successful that usually indicates a hardware problem and an appointment at the Genius Bar of an Apple store is in order.
      Apple Retail Store - Genius Bar              

  • Good day please help me, my iphone 5 wont turn on.  i have tried the hard reset . but that didnt even work. i plugged it in charger but still no response i connect it in itunes still.dont open. please help. i dont have the warranty anymore, i

    good day please help me, my iphone 5 wont turn on.  i have tried the hard reset . but that didnt even work. i plugged it in charger but still no response i connect it in itunes still.dont open. please help. i dont have the warranty anymore, so please help.me.

    Please make a Genius Appointment and take it in for service. By now it probably cannot be fixed, but you never know.

  • My iphone wont turn on when connected to a laptop or pc,but when its connected to my dock, its shows it need restoration what should i do?

    my iphone wont turn on when connected to a laptop or pc,but when its connected to my charging stereo,its shows i need to conect to itunes but then after 10-15 min. it turns off.

    Hi Monzairita,
    Thanks for visiting Apple Support Communities.
    If your iPhone only powers on when connected to a dock, and shows the "connect to iTunes" screen, start with these troubleshooting steps:
    iPhone: Hardware troubleshooting
    http://support.apple.com/kb/TS2802
    Will not turn on, will not turn on unless connected to power, or unexpected power off
    Verify that the Sleep/Wake button functions. If it does not function, inspect it for signs of damage. If the button is damaged or is not functioning when pressed, seek service.
    Check if a Liquid Contact Indicator (LCI) is activated or there are signs of corrosion. Learn about LCIs and corrosion.
    Connect the iPhone to the iPhone's USB power adapter and let it charge for at least ten minutes.
    After at least 30 minutes, if:
    The home screen appears: The iPhone should be working. Update to the latest version of iOS if necessary. Continue charging it until it is completely charged and you see this battery icon in the upper-right corner of the screen . Then unplug the phone from power. If it immediately turns off, seek service.
    The low-battery image appears, even after the phone has charged for at least 20 minutes: See "iPhone displays the low-battery image and is unresponsive" symptom in this article.
    Something other than the Home screen or Low Battery image appears, continue with this article for further troubleshooting steps.
    If the iPhone did not turn on, reset it while connected to the iPhone USB power adapter.
    If the display turns on, go to step 4.
    If the display remains black, go to next step.
    Connect the iPhone to a computer and open iTunes. If iTunes recognizes the iPhone and indicates that it is in recovery mode, attempt to restore the iPhone. If the iPhone doesn't appear in iTunes or if you have difficulties in restoring the iPhone, see this article for further assistance.
    If restoring the iPhone resolved the issue, go to step 4. If restoring the iPhone did not solve the issue, seek service.
    Best Regards,
    Jeremy

  • My iphone 4s wont turn on with out being pluged in and when i unplug it it dies instantly i pluged it in put it in dfu mode and tried to restore it hoping it might help but its stuck in dfu and has restore error 21 help!!!

    my iphone 4s wont turn on with out being pluged in and when i unplug it it dies instantly i pluged it in put it in dfu mode and tried to restore it hoping it might help but its stuck in dfu and has restore error 21 help!!!

    Hey jestinsinclairr,
    Thanks for using Apple Support Communities.
    After reviewing your post, it sounds like you had one issue and then got a second trying to resolve the first. A frustrating situation for sure. The first article linked has what to do if it is not powering on unless plugged in. The second article addresses the error you are receiving when trying to restore.
    iPhone: Hardware troubleshooting
    http://support.apple.com/kb/TS2802
    Will not turn on, will not turn on unless connected to power, or unexpected power off
    Resolve iOS update and restore errors
    http://support.apple.com/kb/TS3694#10
    Check for hardware issues
    Related errors: 1, 3, 10, 11, 12, 13, 14, 16, 20, 21, 23, 26, 27, 28, 29, 34, 35, 36, 37, 40, 1000, 1002, 1004, 1011, 1012, 1014, 1667, or 1669.
    Have a nice day,
    Mario

  • My iPhone 5 wont turn on after i tried to update from 6.1.3 to 6.1.4.

    my iPhone 5 wont turn on after i tried to update from 6.1.3 to 6.1.4. My Phone refuses to turn on. i bought my iPhone from someone else and i don't know if the warranty is voided, how can i find out if is voided ?

    First try a Reset  ( No Data will be Lost )
    Press and hold the Sleep/Wake button and the Home button at the same time for at least Ten seconds... (But can take Longer)... until the Apple logo appears. Release the Buttons
    If no joy... Try a Restore...
    1: Connect the device to Your computer and open iTunes.
    2: If the device appears in iTunes, select and click Restore on the Summary pane.
    Restoring  >  http://support.apple.com/kb/HT1414
    3: If the device doesn't appear in iTunes, try using the Steps in this article to force the device into Recovery Mode.
    Note on Recovery Mode.
    You may need to try this More than Once... Be sure to Follow ALL the Steps...
    Once you have Recovered your Device...
    Re-Sync your Content or Restore from the most Recent Backup...
    Restore from Backup  >  http://support.apple.com/kb/ht1766

  • My Iphone 4 wont turn on!

    My IPhone 4 wont turn on.
    I have tried holding both buttons in & tried connecting to laptop whilst holding down the home button but still nothing!!
    Is it dead???

    This really helped me a lot! It's restoring right now. Thank you so much for your help, I was about calling Apple Support, but it wasn't necessary. Thank you!

  • My Iphone 4 wont turn on, but if i have it plugged in the wall for in long time it turns on by itself and gets stuck at the apple logo

    My Iphone 4 wont turn on, but if i have it plugged in the wall for in long time it turns on by itself and gets stuck at the apple logo.
    i've tried everything but it still doesen't work, can you please hep me?

    First - Press both home button and switch on/off for 15 seconds it will reboot,If it does't work try 
    second -  connect ur iphone to system and open itunes then Press and hold both home button and switch on/off for 15 seconds phone will reboot then as soon as apple logo appears leave switch on/off without leaving home button it will go to restore mode then restore ur phone with latest version.
    Hope this will resolve ur issue but all ur data will be errased.
    Thanks

  • My iphone 5s wont turn

    iphone 5s wont turn on. when i plug it in i get a white screen, with a black apple logo for a minute then just a black screen. Ive tried restoring it then i get an error "2009"

    I found this using Google:
    Hello Friend
    1.Connect your iPhone to the computer and open the iTunes.
    2.Make sure you iPhone is selected from the left menu in iTunes.
    3.Then click the restore button in the center of the iTunes summary tab.
    4.After that select the back up the contents of your iPhone to the computer.
    5.iTunes will ask if you are ready to restore the iPhone.
    6.Your data and settings from the device. click the restore.

  • My iphone phone wont turn on and when i plug into computer it wants to restore then gets stops at the 'waiting for iphone' what do i do? not jailbroken not damaged? HELP!!!!!

    my iphone phone wont turn on and when i plug into computer it wants to restore then gets stops at the 'waiting for iphone' what do i do? not jailbroken not damaged? HELP!!!!!

    i have, its connected to my sisters computer,it starts to restore then says there was a problem downloading the software for the iphone, the network connection has timed out. what does this mean?

  • My iPhone 4 wont turn on, It wont go passed the charging icon and then when I take the charger out it says it needs charge. Its not the charger as iv tried several and holding lock and home button doesnt work please help!!!!!

    My iPhone 4 wont turn on, It wont go passed the charging icon and then when I take the charger out it says it needs charge. Its not the charger as iv tried several and holding lock and home button doesnt work please help!!!!!

    Hello there, Conorjl7.
    The following Knowledge Base article provides some good, practical steps for troubleshooting issues with charging:
    iPhone and iPod touch: Charging the battery
    http://support.apple.com/kb/HT1476
    Particularly:
    If your battery doesn't charge, or if your device shows a low-battery image, black screen, or "accessory not supported" alert, follow these steps.
    Inspect the connector at the bottom of the phone:
    Make sure that there are no bent pins in the connector.
    Make sure that the connector is free from debris.
    If there are bent pins or debris, please contact Apple Support.
    Otherwise, continue troubleshooting.
    Make sure that the outlet you're using works.
    Make sure that the Apple USB cable and Apple USB power adapter work.
    Plug the device in to power and let it charge for up to 30 minutes. If you don't have an Apple USB power adapter, try connecting to a computer's high-power USB 2.0 port (not a keyboard). The computer must be on.
    If the device still exhibits an issue, try turning your device off and then on again while connected to power.
    If the issue is persists, please contact Apple Support.
    Thanks for reaching out to Apple Support Communities.
    Cheers,
    Pedro.

Maybe you are looking for

  • Populating the Lookup values in AD Child Form

    HI, Below is the Lookup code format. Codekey , Decodekey IT-Development , IT-Development IT-Testing , IT-Testing IT-Production , IT-Production HR-system , HR-system HR-...... , HR-...... HR-...... , HR-....... In AD Process Form one of the field cont

  • Moving Data from one table to another table

    Hi, I've a requirement to move large volumes (few billions) of data from one table to another empty target table. The target has more number of attributes and may not have same attribute name as the source. Please let me know what's the best method u

  • HP Laserjet M1132 MFP on my MacBook Air.

    I have installed HP Laserjet M1132 MFP on my MacBook Air. The scanner does work but the printer doesn't. After sending the page to print it shows on the screen that printing is finished but no printed picture goes out. What should I do?

  • PI 7.1 Architecture and components

    Hi SDNers, I would like to know the architecture and components of SAP Process Integration 7.1. Your inputs are valuable. Thanks in advance, -Saravanan.

  • Using the effect/distort&transform/transform... menu

    Mac 10.7.4//Illustrator CS5.1 (15.1.0) 1) I had group consisting of several objects 2) I used the subject effect to create two copies spaced horizontally apart 3) Now I need one more copy of the original further yet horizonally,  selecting the origin