IPhone 5 apple logo flashing when on charge.

My iPhone 5 randomly turned off last night and I was unable to turn it on. I then plugged it into a charger and the apple logo appeared and then went again. This flashing has been happening continuously - black screen for 5 seconds, apple logo for 10 seconds.
I found that if I held the power button 3 seconds, then also held the home button at the same time for ten seconds and the released the power button and held just the home button for another 10 seconds, the flashing stops and the screen goes black.
However, the flashing only occurrs when my device is plugged in to charge, if it isn't it is just a black screen, no matter what buttons I press.
I looked on the internet and they all say hold the power button and home button for 6/10/12/60 seconds, which does not help. Others say I have to restore it, but I havent backed up my phone in a while and all my important photos are on there that I do not want to lose. I then downloaded the software EaseUS MobiSaver which advertises that you can back up your phone even if it doesn't turn on. This also failed to work and the software cannot pick up that my iPhone is plugged in.
Also iTunes only picks up my device when its in restore mode but says I have to restore it before I can do anything further on iTunes.
Is there another way to fix it without restoring?
Thank you and sorry for rambling.

Hi there socko0603,
At this point, the next troubleshooting step is to restore the device in iTunes, there is no way out of Recovery Mode without restoring. Take a look at the article below for more information.
If you can't update or restore your iOS device
http://support.apple.com/kb/ht1808
If you continue to experience issues, take a look at the article below for some additional troubleshooting steps.
iPhone: Hardware troubleshooting
http://support.apple.com/kb/ts2802
-Griff W.

Similar Messages

  • Apple logo flashes when plugged in. can not use at all

    every time i plug my ipod to my computer or any power source. the apple logo flashes and i am unable to restart, reset, or any other 'r'. has anyone else had this problem?

    On standalone, disconnected from PC,
    What do you see on the iPod screen?
    What is the iPod battery level?

  • Iphone 3gs apple logo flashing

    I have an iphone 3gs that does nothing when not plugged in but when i plug it into the computer and the apple logo will come on and go off.  I plug it into the wall charger and it boots up but says the phone needs activated and wont let me do anything else and when i unplug it to plug it into the computer it shuts off.  I have put it in dfu mode and it goes to restore but at the end of the process when almost done the phone shuts off.  ive looked up every way possible to fix it and have done everything but have had no luck..

    Hi following the "hardware" problem I purchased a new iphone 4 as i didn't want to pay £120 for another 3GS only to find a problem on the next update.
    However yesterday following reading a few forums i decided to give it one last try - rebooted phone and it is now working!!! I am so angry as 5 staff  in 2 Apple shops all said it was hardware. I was in an Apple shop for an hour whilst they tried everything to get it working. Obviously this is not the case and going by the number of threads on this problem it is a massive issue. It's not surprising Apples profits are up if people are having to replace perfectly working Iphone 3s.
    Apple have to own up to this it is not acceptable.
    I am off back to Apple tomorrow as i am not going to let this rest especially as i am £500 worse off. Will keep you posted

  • 1st gen ipad stuck on apple logo only when on charge

    I have an iPad that got wet in the rain, when I brought it in it still worked ( i pressed the home button and the homepage came up with all the apps) so I quickly dried if off and put it in the airing cupboard for 6 days, now when I plug it in to the mains with the charger the apple logo comes up for about 15 secs then disappears then comes back on after about another 30 secs and this keeps happening and won't go any further and when I unplug it and link it to my apple laptop nothing happens at all it nothing happens at all (doent show the apple logo or charging logo)  i dont think its taking any charge please let me know if anyone knows how to fix x

    Bluequasar-
    There is a way to force the iPad into recovery mode.  See <this article>
    Fred

  • I have an Iphone 3g and i can't turn on, but if i plug it on the Iphone charger i can see the Apple Logo but it quickly disappears(Apple Logo SOD)  When I connect it to the computer it won't charge and it won't turn on

    I have an Iphone 3g and i can't turn on, but if i plug it on the Iphone charger i can see the Apple Logo but it quickly disappears(Apple Logo SOD)  When I connect it to the computer it won't charge and it won't turn on, I tried DFU mode and it doesn't work. I tried STABBING IT(lol, it works sometimes) and i doesn't work again. If i can't connect it to the computer i can recover it but i know that it still works. WHAT SHOULD I DO!!!!!

    http://reviews.cnet.com/8301-19512_7-10115048-233.html
    http://support.apple.com/kb/TA38633
    Apple suggest a removal and re-install of iTunes to get over the 1601 / 1602 error message.
    Other sites suggest trying a different USB socket… direct to the PC / Mac not a hub.
    edit to add usb info.

  • When i switch my iphone on the apple logo flashes on then off

    when i switch my iphone3 on the apple logo flashes on then off.

    Try leaving it on a charger? Might be low battery life.
    Try a hard reset holding the Home button and sleep/wake button ( The circle button, and button on top)

  • I dropped my phone in water and put in rice for 3 days and plugged it into my computer but it keeps flashing the Apple logo and a no charge sign. It also is not connecting to my computer and it does not say "Amelia's iPhone" in iTunes

    And then put in rice for 3 days and plugged it into my computer but it keeps flashing the Apple logo and a no charge sign. It also is not connecting to my computer and it does not say "Amelia's iPhone" in iTunes

    Put it in rice for another 4 days.

  • When i plug in my ipod touch (8gb, 3rd generation) it doesn't turn on and the apple logo flashes on and off. how can i stop it and turn on my ipod??????

    when i plug in my ipod touch (8gb, 3rd generation) it doesn't turn on and the apple logo flashes on and off. before this it wouldn't turn on unless it was plugged in.

    Try:
    - iOS: Not responding or does not turn on
    - Also try DFU mode after try recovery mode
    How to put iPod touch / iPhone into DFU mode « Karthik's scribblings
    - If not successful and you can't fully turn the iOS device fully off, let the battery fully drain. After charging for an least an hour try the above again.
    - If still not successful that usually indicates a hardware problem and an appointment at the Genius Bar of an Apple store is in order.
      Apple Retail Store - Genius Bar

  • HT3529 my iphone 5 apple logo keeps flashing

    my iphone 5 apple logo keeps flashing

    abj1953 wrote:
    my iphone 5 apple logo keeps flashing
    The Basic Troubleshooting Steps are:
    Restart... Reset... Restore from Backup...  Restore as New...
    Restart / Reset
    http://support.apple.com/kb/ht1430
    Backing up, Updating and Restoring
    http://support.apple.com/kb/HT1414
    If you try all these steps and you still have issues... Then a Visit to an Apple Store or AASP (Authorized Apple Service Provider) is the Next Step...
    Be sure to make an appointment first...

  • HT201263 My iPhone is stuck on the Apple Logo and when I try to restore I get an unkown error (14)

    My iPhone is stuck on the Apple Logo and when I try to restore I get an unkown error (14) I dont know where to go from here there doesnt seem to be any other discussions like this

    Check USB connections
    If there’s an issue with the USB port, cable, dock, or hub, or if the device becomes disconnected during restore, try troubleshooting the USB connection, then troubleshooting your security software.
    Common errors: 13, 14, 1600-1629, 1643-1650, 2000-2009, 4000, 4005, 4013, 4014, 4016, “invalid response”, and being prompted to restore again after a restore completes.
    To narrow down the issue, you can also change up your hardware:
    Use another USB cable.
    Plug your cable into a different USB port on your computer.
    Try a different dock connector (or no dock).
    Add (or remove) a USB hub between your device and computer.
    Connect your computer directly to your Internet source, with no routers, hubs, or switches.
    If you see your error after changing your USB connections, continue to the next section to troubleshoot your hardware.

  • Ipod nano 6th generation apple logo flashing

    I have an ipod nano 6th generation that when connected to the computer USB it flashes the apple logo.  When not connected, it does not turn on at all.  I have tried all the reset tricks with no impact.  Also, my iTunes does not even recognise it as being connected to the computer.  Any ideas I haven't explored yet?

    Hi magostin,
    Welcome to the Apple Support Communities!
    In situations where your iPod nano is not recognized in iTunes, I would suggest the troubleshooting steps in the attached article. Please use the troubleshooting for Windows or Mac in the article depending on what type of computer you are connecting to. 
    iPod not appearing in iTunes - Apple Support
    Cheers,
    Joe

  • I connect my iPhone to apple, and it says its charging.  However it is not coming up in iTunes so i can add music?

    I connect my iPhone to apple, and it says its charging.  However it is not coming up in iTunes so i can add music?  My phone and iTunes are both upgraded to the latest version.  When i go on my computer, my iPhone is under devices.
    Any suggestions to solve this? 
    Much appreciated.

    Hi Charlesweeks,
    If you are having issues with your iPhone not being recognized in iTunes on your Windows machine, you may find the following article helpful:
    iOS: Device not recognized in iTunes for Windows
    http://support.apple.com/kb/ts1538
    Regards,
    - Brenden

  • Classic: will not recharge; apple logo flashes every few seconds then fades away; have tried the 'reboot' advice i.e. move hold switch on and off, hold menu and center button, no success.  have tried this many times and kept connected for several hours.

    I have a classic, several years old.
    It will not recharge; the Apple logo flashes every few seconds then disappears. 
    I have tried the 'reboot' advice i.e. move the Hold switch on and off, hold the Menu and Center buttons, no success. 
    I have tried this many times and kept the ipod connected for several hours.  And I have tried two different cords, one connected to the desktop computer, one connected to electrical outlet.

    Hi enbridge4,
    If your iPod Classic won't charge or turn on, you may find the following articles helpful:
    Apple Support: iPod won't turn on
    http://support.apple.com/kb/ts1383
    Apple Support: iPod's battery doesn't charge
    http://support.apple.com/kb/ta44551
    Regards,
    - Brenden

  • Why is my G5 is stopping on the grey+apple logo screen when starting up?

    My G5 is stopping on the grey+apple logo screen when starting up and fans run faster than usual after a couple minutes. I have read many of the posts related here, but it seems none are exactly what I am experiencing. Here is what I have done:
    +Disconnected all peripheral devices (except for keyboard and mouse).
    +Unplugged power cord and plugged back in.
    +Unplugged ethernet cable.
    +Removed added memory.
    +Reset the SMU button on the logic board.
    +Reset the PRAM by pressing Command-Option-P-R keys. It makes its second start up chime but I still get the grey screen.
    +After opening the disc door with a paper clip, started up while pressing "C" with Hardware Test CD which found no problems.
    +However, also started up with Systemworks disc and ran Disc Doctor, but I get an "unexpected problem, Error found: disk error" while "Checking Directories: Catalog Structure". When trying to run Speed Disc, my hard drive doesn't even show up in the window to select it. Nor does it show up in Disk Viewer.
    I have not tried to start up from the original Mac Startup or installation disc that came with the computer. I am not at my G5 right now (having to use the internet at work). If I start up with that disc, will I loose any work (if I haven't already) that I haven't backed up?
    Also, the G5 manual suggests replacing the lithium battery inside the tower if I am having problems starting up. I have not read to do this anywhere else except in the manual. It mentions having problems with the date and time which I haven't so I doubt it's the battery.
    Any suggestions?
    Thanks,
    Tony
    G5 Power Mac   Mac OS X (10.0.x)  

    First and foremost you should never use Norton Utilities Disk Doctor or Speed Disk. They will corrupt your hard drive. NUM is not compatible with modern Macs and is no longer supported by Symantec. I highly recommend you uninstall it. You will find instructions here.
    You should do the following:
    Boot from your Tiger DVD. After the installer loads select your language and click on the Continue button, then select Disk Utility from the Utilities menu . After DU loads select your OS X volume from the list on the left, click on the First Aid tab, then click on the Repair Disk button. If DU reports any errors that have been fixed, then re-run Repair Disk until no errors are reported. If no errors are reported click on the Repair Permissions button. Wait until the operation completes, then quit DU and return to the installer. Now shutdown the computer for a couple of minutes and then restart normally.
    If DU reports errors it cannot fix, then you will need Disk Warrior (3.0.3 for Tiger) and/or TechTool Pro (4.1.1 for Tiger) to repair the drive. If you don't have either of them or if neither of them can fix the drive, then you will need to reformat the drive and reinstall OS X.
    If this does not fix the problem, then it's possible your system files have been damaged in which case you may need to reinstall OS X. You can do this by an Archive and Install which does not require erasing the hard drive. However, the hard drive must be verified as OK per the preceeding intructions.

  • Iphone 4 apple logo shows and restarts constantly

    iphone 4 apple logo shows and restarts constantly help please

    Hello Chocoholic123,
    Take a look at the article below, it provides troubleshooting suggestions that will resolve the issue where your iPhone 4 restarting and only showing the Apple logo. 
    iOS: Device unexpectedly restarts, displays Apple logo, or powers off
    I hope this helps, 
    -Jason

Maybe you are looking for

  • Flex builder 3 beta installer doesn't work

    WE are having trouble installing the windows installer version of Flex 3 builder. We tried several machines. We keep getting this screen no matter what we click. ! Please select another location to extract the installer to: This message comes with tw

  • Trying to recover pictures

    My sisters computer is crapping out so they are trying to back everything up to move onto another computer. She can't seem to figure out where the pictures are located that she saved via BlackBerry Desktop Software. I have her HDD in an external case

  • "Purchase couldn't be completed...unable to connect to iTunes". I've tried ALL suggestions...PLZ help.

    I have iPod Touch 4th Gen. I can purchase game token in 1 game but Not the other!! Get message in other game: "Purchase couldn't be completed...unable to connect to iTunes". I've tried ALL suggestions...PLZ help.

  • Filter or Smart Collection for Exported Images?

    I want to keep track of the images I export. (in most cases to skydrive).  Can I set up a filter or criteria for a smart collection to do this? Thanks

  • Edit the clause where in a datablock

    i want to edit the clause where in a datablock in forms 10g je veux que to_date(champdb,'dd/mm/yyyy') = :champforms je fais set_block_property('plombage',DEFAULT_WHERE ,'to_date(dateplomb,'dd/mm/yyyy')= decode(:dateplombage,null,DATEPLOMB,'||:dateplo