IPhone 5 has difficulties to connect by WLAN although the net is recognized., iPhone 5 has difficulties to connect by WLAN although the net is recognized.
iPhone 5 is unable to connect to wifi although Net wasi found.
The Same problem exists at Bluetooth
It Seems to be a Software failure. Does anybody know something about?
BR
Bernd
Look to the right under "more like this", theres plenty about this.
Similar Messages
-
I have a MBP 5.1 with snow leopard 10.6.8. It has been working fine until few days ago, when it started to have different problems:
1) airport is not working well. it is extremely slow, has difficulties in fully loading pages, looses connectivity, It is not browser related, behaves thesame in safari or firefox; it is not the router/wlan; my husband mbp wifi works fine (as it was mine...) and iphone wifi is also working fine. it sees the signal and different networks. , it is also very very slow in opening skype (after that, it is working ok) if I connect via ethernet cable to the same router, everything works perfectly and with the correct speed.could it be a damaged airport card? a software problem/corruption? logic board? (I hope not, the computer is out of apple care now....)
2) after a certain time (more than hours) of use, the trackpad is behaving strangly, increase sensitivity to touch, unwanted selection of folders, files and text or images in web pages when i move the cursor, the cursor jumping all over the places while writing, ecc I have the impression it starts doing that when I use heavily the CPU ( and the temperature goes up). Is this again a problem of the mother/logic board?
I had recently serviced it since it was not booting properly, but except some permissions repaired, they did noit find anything wrong in the hard drive (which I have now substituted with a SSD) or other hardware.
thanks in advance for any help/suggestions
alessandraI think I solved the wifi connection problem, just by switching off completely the router! sounds trivial, but in this case it worked!!!
the funny behaviour of the trackpad/cursor still persists. any suggestion???
thanks again -
I have a IPhone 4s. No WLAN connection possible.
I have a IPhone 4s. No WLAN connection possible. Clearly a manufacturing error. After only 2 years: Apple stores and Apple care ignore it. Who can help me, is there any goodwill department? Christian from Hamburg / Germany
This is a well-known fault, which has affected thousands of iPhone 4S worldwide.
Yes it is a "hardware failure" but the fact is that the hardware fails BECAUSE of a manufacturing error. So let's not get too caried away with the semantics. What appears to have happened is that thousands of 4S phones were manufactured with a faulty batch of wi-fi chips that carried a latent (dormant) fault, which only "fried" the wi-fi chip when people upgraded to the latest iOS from Apple. Especially if they upgraded over wi-fi instead of via iTunes. And of course many upgrades were performed when the phones were just out of warranty. If Apple were still a responsible company they would do what car manufacturers do and recall all the faulty iPhones to replace the wi-fi chip free of charge. Trying to say "once it's out of warranty we don't care about you" does not exactly endear Apple to the affected, who are taking to social media in their thousands to try to dissude anyone from buying Apple products. Apple customers deserve better than this. -
My iphone3gs has been turning off and turning on , even at every%. it has been doing that for quit a good bit now. now my iphone is still doing the same thing, but once it came back on its saying connect to itunes. i have my itunes pulled up, but my iphone is not being recgonized. what can i do... could i get a new iphone for free, and keep my gophone plan? please help? what can i do?
Hi there Jackie Silver,
I would recommend taking a look at the troubleshooting steps found in the article below.
iPhone: Hardware troubleshooting
http://support.apple.com/kb/ts2802
Will not turn on, will not turn on unless connected to power, or unexpected power off
Verify that the Sleep/Wake button functions. If it does not function, inspect it for signs of damage. If the button is damaged or is not functioning when pressed, seek service.
Check if a Liquid Contact Indicator (LCI) is activated or there are signs of corrosion. Learn about LCIsand corrosion.
Connect the iPhone to the iPhone's USB power adapter and let it charge for at least ten minutes.
After at least 30 minutes, if:
The home screen appears: The iPhone should be working. Update to the latest version of iOS if necessary. Continue charging it until it is completely charged and you see this battery icon in the upper-right corner of the screen . Then unplug the phone from power. If it immediately turns off, seek service.
The low-battery image appears, even after the phone has charged for at least 20 minutes: See "iPhone displays the low-battery image and is unresponsive" symptom in this article.
Something other than the Home screen or Low Battery image appears, continue with this article for further troubleshooting steps.
If the iPhone did not turn on, reset it while connected to the iPhone USB power adapter.
If the display turns on, go to step 4.
If the display remains black, go to next step.
Connect the iPhone to a computer and open iTunes. If iTunes recognizes the iPhone and indicates that it is in recovery mode, attempt to restore the iPhone. If the iPhone doesn't appear in iTunes or if you have difficulties in restoring the iPhone, see this article for further assistance.
If restoring the iPhone resolved the issue, go to step 4. If restoring the iPhone did not solve the issue, seek service.
Issue not resolved
My issue is still not resolved. What do I do next?
Contact Apple Support.
-Griff W. -
Can't connect iphone,ipad,samsung to WLAN.
Hi everybody!
I'm having a headache with a problem, i hope you can help me guys.
We have a WLC 5508. This WLC has a guest network, which SSID was hidden. Now that i want to use, i enable the SSID broadcast
and try to connect to it.
With my laptop, or any other computer i don't have any problem. But with the gadgets (an iphone, ipad and samsung) i've been having some issues.
I can tell that, at the beginnning i thought that maybe it was a problem with the devices and the encryption i was using on the WLAN (WPA2 PSK). But
these devices can connect to another WLAN network in the same WLC, with the same encryption without a problem.
I try to change the encryption, i used all of the possible ways, even i let it opened, but nothing worked for me.
I'm not an expert on wireless, and i don't know if i'm missing a command or something.
Thanks everybody for your time, i really hope you can help me! :-)Duplicate post: https://supportforums.cisco.com/thread/2266804?tstart=0
Thanks,
Scott
*****Help out other by using the rating system and marking answered questions as "Answered"***** -
Is there any way to get a log of the bluetooth devices my Iphone has been connected to? I recenly had my Bluetooth Jabra stolen from my car and now a simliar one is on Craigslist. I'd like to give my connection log to the police before I go and see if my Iphone recognizes the device in question. Any way to get any type of bluetooth device connection log out of my iphone?
Your contacts should still be on whatever program you sync your iphone to (i.e. Outlook, address book).
The iphone is not a stand alone device. It is designed to be synced with a computer. If you have not been syncing with a compatible program, then you are out of luck. Your contacts are not included in the back-up because it is meant to be synced with your computer.
"Although iTunes backs up most of your iPhone and iPod touch settings, downloaded applications, and other information (Contacts, calendars, notes, images in the Camera Roll), your audio, video, and photo content are not included in the backup."
http://support.apple.com/kb/HT1414 -
my iphone 4s and ipad2 both with 7.0.4 update will no longer connect to wifi.
About three days ago the ability to connect came and went and the connection never lasted more than 10-15 minutes; it has not been able to connect since last night. I do not think it's my wifi router as non-mac lap top has no issues. I have seem many similar questions posted.Reboot your router by removing all power from it for about 15 seconds. Also, if your router still has its default SSID (such as LINKSYS, DLINK, NETGEAR, etc) change the SSID to something unique. Note that all other devices on your network will have to be reconnected if you change the name, but if the name is still the default that is most likely your problem.
If the SSID is not the default then the reboot should fix it. -
Hi Apple Team, my iphone can't share bluetooth files with my macbook pro. But other devices can share bluetooth files with my mac book pro. Please, kindly open up bluetooth to accept all connections from all devices. Now it difficult for me to share bluetooth files from my mac bookpro to my iphone, unless i attached it through email.
We need it to be acceptable to all devices.
Thank you!You can tell Apple directly at the link below.
http://www.apple.com/feedback/iphone.html -
My iphone has lost connection to the server; I cannot get e-mails.
My iphone has lost connection to the server; I cannot get e-mails. What can I do to fix that?
I recently put on a PowerPoint presentation at DU, in Denver Colorado; signed on as DU guest to access Internet link. SInce then I haven't been able to get e-mail on my Iphone - Cannot Get Mail, Server Stopped Responding. I tried all previous suggestions, such as rebooting phone, updating software etc. I went to MacBook Pro and tried logging on to yahoo e-mail. Apparently there was a security risk to my e-mail account so Yahoo locked up my account. I reset my password, it was verified through text message, and Voila it worked. Don't forget you also have to change this on your Iphone: go into settings; Mail, Contacts, Calendars; click on your e-mail browser, then account and enter your new password, click done and it will verify on you phone as well. Hope this helps!!!
-
Dear apple, I am really dissapointed with you. Around January 2013, my iPhone 4s 16GB White has hardware issues, which was the Wi-Fi grey out. The wifi grey out means that I can't access the wifi on/off button, and also it has no connection. I have put up with it for months, until june 7 when I decided it has been long enough, and I got a replacement. I told the genius bar what happened, and I already did the so called "steps" that apple reccommended on the site, which was reset network settings, restore iPhone. The genius bar gave me a replacement phone, so I was expecting that the problem would be over, but it isn't. It seems that it's iOS 6.1.3 which is the case of most public complaints on apple iPhone products. Not even 3 weeks after I got the phone replaced, it is doing it again, so I suspect I'm just going to get a replacement again? Unfortunately I only have until 5th of july 2013 until my 1 year warranty is up. After that, any issue I have, I have to purchase apple care. People are expecting this problem to be fixed but I don't see it being solved any time soon. This is horrible and really low, because I have been a good customer, when I talk to the people at the genius bar, I show the utmost respect I can to them for the work they put into their job, but somewhere there is a problem where something has gone wrong. Because of that, people that only have a one year warranty (which i received because I purchased my apple iPhone at an Optus outlet, once that one year warranty is up, I have to pay for a problem that isn't even my fault? That isn't how it should work, you should be fixing this problem so people can be happy customers and leave happy. Obviously you don't all know how to do your jobs, because if you did, we wouldn't have this problem. I would like a replacement phone, ONCE AGAIN. If this problem occurs again, I will simply stop buying your products, and lose faith in your company, your's sincerely, Jack Maher.
This is a user to user help forum only. You are not addressing Apple here.
My iPhone 4S, iPhone 5, and iPad 2 are running 6.1.3 with no such problem and the same with the overwhelming majority of iOS devices running 6.1.3. -
I have recently got an iPhone 4 out of no where it has decided to think that my headphones are in and they are not but does work with headphones in.
Then later on within the same day it after turning my phone on and putting it on charge it comes to the screen stating to connect to iTunes/emergency calls only/no service so I connect it iTunes and it says we are unavailable to continue with your activation at this time. Please try again later, or contact customer care.
HELP!the same problem but i used it already for 3 years my iphone 4, when i update to ios 6.1.3 version, now is failure like said.
we are unable to continue with your activation at this time please try again later, or contact customer care
any help please. i am here in saudi arabia city of jeddah.
thank you very much in advance
pabs -
I have Words with Friends app on my iphone4S and the same game on computer. When I try to play Words with Friends with Facebook on the iphone the message says" Account Already Connected. This Facebook account has been connected to another user." It is connected to my computer. How can I play game on iphone?
Hi Grandmaz5,
If you are having issues connecting to Facebook on your iPad, and you have already troubleshot the Facebook app itself, you may want to check the built-in iOS settings for Facebook; you may find the following article helpful:
iOS: Using Facebook, Twitter, and other social network accounts
http://support.apple.com/kb/HT5500
Regards,
- Brenden -
My iPhone 5S has not connected to 4G LTE service in the last few days? Is there an outage/issue with 4G in my area (Pittsburgh) or is this a device specific issue?
JHblues Let's get your data working again. There are not any reported issues in the area. Try this step: http://vz.to/1kUSSk2
Sheritah_vzw
Follow us on Twitter
@VZWSupport -
hey everyone.. i have a problem with my 3Gs iphone.. i updated to the ios5 and now when i open it says that i have to connect it with the itunes. when i connect it says that has an error 28 something like that.. can anyone help me to fix it?? Regards
Error 23, 28, 29: These errors may indicate a hardware issue with your device. Follow the steps in this article. Also attempt to restore while connected with the white USB Dock Connector cable that shipped with your device, on a known good computer and network to isolate this issue to the device. The MAC address being missing or the IMEI being the default value, (00 499901 064000 0), can also confirm a hardware issue. Out-of-date or incorrectly configured security software can also cause these errors.
-
The memory on my Phone is really bad so i cant store much. The pictures i am trying to import are really important and i cant lose them. My phone has been playing up a lot and im afraid of losing the pictures so tried to import them onto my laptop. Its a windows 8 and every time i connect my iphone a window automatically opens titled "Apple iphone" but underneath it says "no files or folders". How can i resolve this?
Also the apple store have told me not updating may be causing problems but i cant update due to no space. i have 3 apps, around 300 photos/videos and no music. it is 16gb so i dont know why im having this problemThis is how you import photos/videos:
http://support.apple.com/kb/HT4083
Is that what you're doing?
Maybe you are looking for
-
I purchased iTunes Match to transfer all 6gigs of music from my storage to icloud. The download is complete and all music has been transferred to icloud but on my iPhone I'm still using the 6gigs which defeats the whole purpose. Question: can I delet
-
ERLA/NORM, Header and Item Level Pricing Issue
Dear All, I have an issue wherein, even though I have used ERLA for BoM Item and NORM for Subitems, in sales order Conditions, both header level and item level pricings are active. Correct me if I am wrong, item level pricing should get deactivated.
-
Greetings when Im defining a maping theres a button to make automatic mappings when the names of the source and destination are the same. Since I upgrade to SP 22 (XI 3.0) this button is allways disable, do you know why this thing happens? Thanks for
-
Using SXPG_CALL_SYSTEM to execute Unix 'MV' command not working
Here is the code (method - params begin with "p_"). This returns no error but yet the file is not moved (called in a test program). Any ideas? DATA: lv_sourcepath TYPE rlgrap-filename, lv_targetpath TYPE string, lv_fname TYPE r
-
Input Template: Deriving a member
Hi All, I have the following situation - I have a Dimension "Account" which has a property Division I have another Dimension "Division" The property "Division" of Dimension Account is the same as the Dimension Division. In my Input template I have th