Iphone 5c not activating after factory reset

i recently reset my iphone 5c to factory setting and now im trying to activate it again but it is saying that the activation service is unavailable what should i do???

+Do a DFU recovery:
+1. Open iTunes.+
+2. Connect the iPhone+
+3 Press both the home and sleep/wake buttons until the Apple icon appears (ignore the red slider if it shows).+
+4. Continue pressing the home button alone until iTunes sees your phone in recovery mode.+
+5. Follow the prompts to restore the iPhone.+
This will reset your phone to factory settings.

Similar Messages

  • Windows 8 not active after factory reset

    I bought this laptop a year ago in US, with windows 8 and was upgradable to 8.1. I upgraded and was using 8.1, until 2 days before when system crashed. I was not able to perform a system restore, therefore did a factory reset. Now when the system boots or when i try to upgrade, its asking for an activation code which I dont have. I was in the assumption that the system restore version of windows should have a valid license key but its not the same in my case .
    please advise.
    Additional information: windows update are still working. not sure if this is helpful.
    Thanks in advance for responding.

    HI @Sasikaran ,
    Welcome to the HP Forums!
    It is a terrific place to find answers.
    For you to have the best experience in the HP forum I would like to direct your attention to the HP Forums Guide Learn How to Post and More
    I understand that you have done a factory recovery and it is now asking for the activation code.
    The code is stored in the bios and  it should automatically pick it up .
    Here  is a link to Windows 8 Product Activation to assist you.
    Here is another link to assist you with reupgrading to Windows 8.1
    Updating Windows 8 to 8.1
    Best of Luck!
    Sparkles1
    I work on behalf of HP
    Please click “Accept as Solution ” if you feel my post solved your issue, it will help others find the solution.
    Click the “Kudos, Thumbs Up" on the bottom right to say “Thanks” for helping!

  • Windows 8 not activating after factory reset

    I recently did a factory reset to my Hp Envy 17. Once i went throgh all the steps and signed in to windows 8 I thought I was done since the product key to windows is embedded in the system BIOS. I noticed a little later that my computer was asking me to activate windows 8. So i went into my setting and typed in my windows 8 product key that came preinstalled on my Envy 17. Once I typed in the Product Key  I got a message that said "Activate Windows. The product key on this PC didn't work. You might need to contact the company that built this computer, or buy a new key." I have tried reinstlling windows 3 different times and tried typing in the product key on windows 8 and windows 8.1, both times the product key was not recognised, and i know i didnt type the key incorrectly or have the wrong i double chcked i had the right key by checking on belarc advisor. I have tried many ways to fix the problem and every time it does not work. It seems as though my key has maybe become corrupt some how. I also still have my hp warranty that came with my laptop if that helps at all.

    as far i can tell you and i have not yet restore a pc that is windows 8 yet  but previous versions which i  have had and  never was asked the activation nor it failed to update the pc because it was already activated and stored on microsoft end when you run your computer the first time and also even when i used the extra hard drive and it was window 8.1 iso disc that i got downloaded from microsoft legit-ly from microsoft site  and it appears microsoft recognized my pc because it was related to my email logging on with microsoft email but as  my extra older hard drive from an older defunct pc and when i was upgrading my older vista pc to windows 7 on my second  hard drive on my quad processor pc  it did ask for the product which i have bought from the store and there was no problem with my activation issues with microsoft    

  • LG Ally not activating after factory reset

    Moved for greater exposure

    as far i can tell you and i have not yet restore a pc that is windows 8 yet  but previous versions which i  have had and  never was asked the activation nor it failed to update the pc because it was already activated and stored on microsoft end when you run your computer the first time and also even when i used the extra hard drive and it was window 8.1 iso disc that i got downloaded from microsoft legit-ly from microsoft site  and it appears microsoft recognized my pc because it was related to my email logging on with microsoft email but as  my extra older hard drive from an older defunct pc and when i was upgrading my older vista pc to windows 7 on my second  hard drive on my quad processor pc  it did ask for the product which i have bought from the store and there was no problem with my activation issues with microsoft    

  • HT5312 phone activation after factory reset

    Will a factory reset require reactivation of phone service with the carrier

    Hi, SBtaylor. 
    The iPhone will require the previously used SIM or a valid activated SIM after factory resetting the device. 
    Using an iPhone without a wireless service plan
    http://support.apple.com/kb/HT3406
    Cheers,
    Jason H. 

  • Help!! please email setup requesting enterprise activation after factory reset

    after i did a factory reset i notice my email set up is requesting enterprise activation email and password i don't have either so now my email setup can't work unless i do it and my native browser won't connect and blackberry protect won't work. i registered the blackberry thru hosting and i got your blackberry is registered but i can't get the other apps to work since i need the enterprise activation.

    i got the phone from ebay so i don't know if it's on BES and as far as a blackberry data plan i have verizon prepaid and i activated the phone thru them with no problem and i signed up for BIS with no issues but i don't remember the password to get the service books sent to my phone. the phone just stop working a couple of days ago i have had it since october with no issues until now. the first thing i notice was i stopped getting email and it said my service was blocked so i did a battery pull that didn't work. then i did a security swipe and now i can't access the email setup or the browser and it says that i don't have a data plan needed to use it which i don't get since i have had no problems since october. i was told on by someone that maybe i was over my data but i just looked and saw i wasn't and it rolled back since i paid on the 24. this is like the 3rd incident since switching from post paid to prepaid it is making me want to switch carriers

  • SIM not Valid after factory reset using a non-US SIM card

    I bought an unlocked iPhone 5 at a US apple store.  It worked fine for two years until factory-resetting it.  Now, during the setup process I get a "SIM not valid" message. I tried an iTunes restore to no avail.  I called Apple support and was escalated to two different "experts".  I got two very different answers:
    Expert 1: an unlocked iPhone can be used internationally but can only go through a factory reset with a US SIM card.  Since you don't have one you will have to come back to the US, get an American SIM card, finish the setup process and then you can get back to using it internationally.  There is nothing we can do here at Apple to bypass this procedure.
    Expert 2: Our database shows that your phone is indeed unlocked and is available for use with an Israeli carrier (which is the carrier I am using now).  Either the SIM card is defective or there is a problem with the hardware of the phone.  Please ask for a replacement SIM card from your carrier and if this does not solve the problem you can send it to the US for repair. The repair will be costly.
    Obviously neither of them is solving my problem.  Is there another solution?  Is it time to make the switch to an Android device?

    Sorry if you have already tried this
    Any chance you can ask for a different / new SIM from your carrier?
    or even better see if one of your friends / family has a working phone with a nano SIM
    Try that temporarily in your phone
    If it works = corrupt SIM most likely
    If it does not - please let us know and we can brainstorm further

  • Windows 8.1 update not shown after factory reset

    I had the windows 8.1 update shown on my app store but due to some problems i factory reset the laptop. when i opened it after the restore i was unable to find the update on my store. Rather it shows 96 apps to be updated

    Hi,
    If you want to install Windows 8.1 Update 1, there are two requirements:
    •Windows 8.1 is a prerequisite (vs Windows 8 RTM)
    •KB2919442 is a pre-requisite update - released in March 2014 – you'll need this before 2919355 will be recognized
    http://support.microsoft.com/kb/2919442/en-us
    Alex Zhao
    TechNet Community Support

  • OnPlus not initializing after factory reset

    After a factory reset the unit is sitting with 2 steady amber lights, it doesn't move from here, it's been left for a couple of hours.
    The factory reset is done by holding the reset button for 10 seconds or more then both red lights start flashing for 20-30min then they both turn to solid Amber lights.
    The Factory reset has been tried multiple times.
    Any ideas?

    Hi Alan,
    The solid Amber lights are part of the power on sequence. If both are steady the power on sequence may be hanging.
    Please follow these steps:
    Could you try a factory reset again, this time hold down the reset button for 15+ seconds?
    Also, this time could you try this on a different network? The appropriate ports may be blocked and it isn't able to download it's firmware.
    f you could write the sequence of LEDs you see after resetting and post that. What do you see after the blinking red?
    After trying the above steps and it still fails, an RMA may be required. Please let me know how the steps above turn out.
    Thanks,
    The OnPlus Team

  • Droid RAZR not restarting after factory reset

    Hi,
    I just switched from my old Droid 4 to my sister's old Droid RAZR, which she had no problems with when she last used it. After switching my number over and such, I decided to do a factory reset to wipe off all her information. However, now it won't restart and it's been over an hour since I did the factory reset. It just sits at the eye-looking page and doesn't go any further. Any suggestions on what to do?

        Hi ejackson18,
    I'm sorry to hear that your reset is stuck. I definitely want to get the phone working for you again! Are you able to try the Alternate Methode instead?
    Keep us posted!
    RuthW_VZW
    Follow us on twitter @VZWSupport

  • 7970 will not load after factory reset

    I did a factory reset on a 7970G IP Phone and now it is stuck on boot up. The headset is lit a solid green and the line buttons blink green, top to bottom. The IP Phone has already been swapped for a replacement with the same issue. Anyone know how I can get past this issue?

    To reset the 7970 IP phone to factory defaults, perform these steps:
    Note: The phone must be on a network that provides an IP address and TFTP server address using Dynamic Host Configuration Protocol (DHCP), and the phone must be powered through an external power brick. The alternate TFTP setting is erased when using this procedure, requiring that the TFTP server address is provided by a DHCP server to get the phone upgraded.
    Power off 7970.
    Power on 7970 (with a power brick) while holding the # key.
    The lines lamp should blink amber in sequence. Let go of the # key.
    Press 123456789*0#.
    The lamps should blink green in sequence.
    The phone obtains IP information through DHCP.
    The TERM70.default load loads on the phone.
    The phone should recover the configuration file from Cisco CallManager. If not, reset by typing **#** to restore the configuration.
    If you do not have a power brick connected while doing the factory restore, the process fails because the 7970 cannot TFTP the TERM70.default load from itself with inline power. If you have a console connected, you receive the CDP: power TLV's not detected - assume low power mode - pwr src = 1 message.
    If step 3 does not work, upgrade the phone load to the latest version. Refer to the Software Download and look for these files:
    cmterm-7970-sccp.6-0-1-Readme.htm (Readme for Cisco IP phone load for 7970 IP phone)
    cmterm-7970-sccp.6-0-1.exe (IP phone load for 7970 6.0(1) - Compatible Cisco CallManager version: 3.3, 4.0)
    If this does not work, perform this procedure:
    Power off the phone.
    Hold down the # key.
    While holding #, connect an AC adaptor to the phone.
    Continue to hold # until the line buttons blink amber.
    Release the # key.
    Enter 3491672850*#
    The lights should change color from amber to red. When this occurs, the phone is resetting to factory defaults.
    Note: It is important to try this procedure with a external power supply.
    Upgrading the phone load to 6.0(2) should also solve the problem.

  • My iphone is not activated after i tried to update the os?why?it is showing error?1602

    my iphone is not responding
    i just tried to update it from os 4.1  to 4.2

    Try this support document http://support.apple.com/kb/ts1275.  It states that error 1602 is generally a USB problem. Try an  alternative USB port, or use one on the back of the computer rather than  a hub.

  • 3gs not working after factory reset

    restored factory settings and now have apple logo on screen and phone is doing nothing please help

    If you got this after choosing "Erase all content and settings" in the Reset area of the Settings App on the iPhone the fix is DFU Mode Restore.
    But first do a Reset, Hold both Home and Power buttons until the iPhone begins to restart. Usually less than 20 seconds.
    If nothing, then DFU Mode Restore.
    With iTunes open on Computer, connect iPhone, hold both Home and Power buttons for exactly 10 seconds, release Power button, keep holding Home button until iTunes recognizes iPhone in Recovery Mode. This is usually less than 30 seconds more time. If the iPhone screen is now blank, then this is DFU Mode. Restore iPhone Firmware. If you have the Connect to iTunes screen on iPhone this is Recovery Mode, you try the Restore anyway. If it works great, if not try again to get DFU Mode as I described. Even experienced users can have trouble getting DFU Mode, just keep trying you will get it. DFU = Recovery Mode with blank screen.
    If this does not work and you have Warranty or AppleCare Coverage take iPhone to Apple for resolution.

  • Messages on my MacBook Pro is not working after factory reset, how can I enable it?

    I just recently (yesterday) got my MacBook Pro Mid-2012 restored after having a few issues with it. So it is totally "clean."
    Today I tried to open Messages which worked previously, but it wouldn't let me send a message to anyone (who I could message before the restore) and if I was able to send a message it would show an "Message Can't Be Sent" symbol next to it. I went to Messages > Preferences > Accounts > and saw that my account was enabled but my email used is in a grey font and it will not let me add my iPhone number.
    I have signed in and out, deactivated and reactivated the account and I still cannot message anybody.
    Please help guide me into fixing this, I have looked at other boards and it doesn't really help me with my predicament. How can I send a message?
    Also in the Messages menu, "My Status" is grey and I can't click anything and as well with the "Log In" option. If this can help developing an idea of what might be wrong.

    It won't send it to other emails, but it will for phone numbers. Not sure why, but if you can help with sending to other iMessage emails I would appriciate it :-)

  • Touchpad not working after Factory reset through Desktop manager os6 BB 9300 curve

    sir,
          I tried to factory rest my blackberry curve 9300 through desktop manager but the thing is after booting up im getting a licence agreement popup but im unable to scroll down.
    dont know why ??
    please help me

    Hello vamsy_sid and welcome to the BlackBerry Support Community Forums.
    Sorry to hear you're having an issue with your device.
    Did your trackpad function normally before you did the reset?
    IfyouhittheSpacebaronyourdevice, doestheagreementscrolldowntotheIAgreeorIDisagreeboxes? 
    If you reboot by pulling the battery, are you then able to scroll down on the agreement?
    -HMthePirate
    Come follow your BlackBerry Technical Team on twitter! @BlackBerryHelp
    Be sure to click Kudos! for those who have helped you.Click Solution? for posts that have solved your issue(s)!

Maybe you are looking for

  • Report footer = Entire size of page, CR still breaks section

    I have a report that has large text boxes in a report footer.  The section is checked "Keep Together" so it will print in its entirety on the last page of the report.  I also have a rather large page header that occupies probably the top third of the

  • Using a single master data infoobject for multiple fields

    Hello experts. Today I ran un with the following problem: I am modelling an Infocube and will be receiving a flat file with several fields, of which 3 of them give information about sales representatives. For each transaction there are 1-3 sales repr

  • No iTunes exclamation marks, but iTunes still says 70 songs are missing

    Hi all, I have had this problem for a while now and haven't found it addressed anywhere online (tried searching in this forum as well as other forums through Google Search for quite a while). Here is the issue: My music library occasionally shows exc

  • Dowloading Adobe Acrobat Pro XI

    After Windows 8 crashed, I'm rebuilding my system and now need to download Acrobat Pro XI, which I purchased last year and for which I have the registered serial number in My Adobe. How do I do this? Thank you very much in advance for your help!

  • Does labview provide epoch time converter support?

    Hi, My product creates a data log file with time stamp. The time stamp is of the epoch format. The system is based on the linux. So I assume that this time stamp is a unix based format. How  should I convert this time stamp data to the UTC format in