Iphone hung while updating the ios what should i do ?

iphone hung while updating the ios what should i do ?

Placing your device into recovery (DFU-Device Firmware Upgrade) mode:
Follow these steps to place your iOS device into recovery mode. If your iOS device is already in recovery mode, you can proceed immediately to step 6.
   1. Disconnect the USB cable from the iPhone, iPad, or iPod touch, but leave the
       other end of the cable connected to your computer's USB port.
   2. Turn off the device: Press and hold the Sleep/Wake button for a few seconds
       until the red slider appears, then slide the slider. Wait for the device to turn off.
              * If you cannot turn off the device using the slider, press and hold the
                Sleep/Wake and Home buttons at the same time. When the device turns off,
                release the Sleep/Wake and Home buttons.
  3. While pressing and holding the Home button, reconnect the USB cable to the
       device. The device should turn on. Note: If you see the battery charge warning,
       let the device charge for at least ten minutes to ensure that the battery has some
       charge, and then start with step 2 again.
  4. Continue holding the Home button until you see the "Connect to iTunes" screen.
       When this screen appears you can release the Home button:
  5. If necessary, open iTunes. You should see the following "recovery mode" alert:
  6. Use iTunes to restore the device.
If you don't see the "Connect to iTunes" screen, try these steps again. If you see the "Connect to iTunes" screen but the device does not appear in iTunes, see this article and its related links.
Note: When using recovery mode, you can only restore the device. All user content on the device will be erased, but if you had previously synced with iTunes on this computer, you can restore from a previous backup. See this article for more information.

Similar Messages

  • My iPhone 4S has locked up while updating the ios. what do I do?

    my iPhone 4S has locked up while updating the ios. what do I do?

    Reset your device: hold down the home button along with the sleep/wake button until the screen goes black and you see the Apple, then let go. Then try it again.

  • TS3694 i am getting a 1015 error on my iphone 3G. i just did update the ios. what happen to my iphone?

    I am getting a 1015 error on my iphone 3G. i just did update the ios. what happen to my iphone?

    SEARCH!!!!
    http://lmgtfy.com/?q=iphone+1015+error

  • Lost all my iphone songs while updating to ios 7. how do I get them back?

    I lost all my iphone songs while updating to ios 7. how do I get them back?

    Restore the backup you surely made before you updated, as anyone would do before updating any computing device:
    iOS: Back up and restore your iOS device with iCloud or iTunes

  • My backup can not be restor for my iphone after i update the ios to 7 for iphone 5

    hello
    i need your help thats very important for me
    please guide me to solve this problem
    i back up my iphone before i restore the phone for update the ios
    then after change the ios to seven and it turns on the phone and request for restore the backup and i select the only last backup in my itunes and it stared to restore after a moments give me an error not to restore the backup
    and when i search the pc i thouth it exsist
    i had a lot of important information on that
    please help me

    You cannot.  However, your iCloud backup will be available to you in the current release of iOS (7.0.2).

  • While updating the ios, the configuration is not completed and iphone's earlier ios is also lost

    Please Help

    Hi AakashGhare,
    According to your error message, SQL Server 2008 databases are version 655. SQL Server 2008 R2 databases are 661. When you are trying to attach an 2008 R2 database (v. 661) to an 2008 instance and this is not supported. As other post, once the database has
    been upgraded to an 2008 R2 version, it cannot be downgraded. You'll have to either upgrade your 2008 SP2 instance to R2, or you have to copy out the data in that database into an 2008 database (such as using the data migration wizard).
    In addition, if you want to use a Windows Batch file code and command to automatically login to SQL Server, detach database and attach a new one database, there is a similar details about batch code for attaching database to a new database, you can refer
    to this article.
    http://notesbyparth.wordpress.com/2012/06/29/run-sql-commands-from-windows-batch-file-or-attachdetach-database-automatically-using-batch-script/
    Regards,
    Sofiya Li
    Sofiya Li
    TechNet Community Support

  • HT1766 I didn't back up my iphone and i updated the software what can i do

    I updated my iphone yesterday (iso6) and now I have to restore my mobile through itunes and I didn't make a back up to my contacts and all my data on the mobile if I restore it I will loose everything or the iphone make a backup automatically.

    All your information should be on the computer you have regularly been Syncing and Backing up to...
    See Restore from Backup here  >  http://support.apple.com/kb/ht1766

  • Error code "-1" while updating the iOS from IPAD2

    When I try to update my IPAD2 to iOS 4.3.2 I receive the error code "-1" at the end of the installation, and now I´m stuck in the restore point, because the system don´t boot anymore. When I connect to Itunes it says I have to download the update, then the error appear again, and this is going over and over... Any hints here?

    i dont 'now  whay people of apple company not concern about this probleme .
    i am facing the the same that you have . no one answer . please good felwo  help us

  • IPhone locked while updating to iOS 7

    what do I do?    

    What do you mean by locked?. If you could describe the issue a bit more indepth then one of users on here may be able to help you

  • HT1222 While downloading the iOS 7.1.1 it is asking for password which password I am suppose to enter

    While updating the iOS 7.1.1 it is asking me for password I did enter the apple password it not taking it,,,,
    Please help

    Enter the 4 digit passcode that you use to unlock the iPad or if you don't use the 4 digit code, use the more secure password that you set up to unlock the device.
    Bottom line is that you need to enter the passcode/password that you use to unlock your iPad.

  • Hi, my iphone 5 encountered an unknown error while updating to iOS 7 via itunes and is now stuck in recovery mode and prompts me to restore the phone when I connect it to itunes but then I would lose all my data. Any suggestions please?

    Hi, my iphone 5 encountered an unknown error while updating to iOS 7 via itunes and is now stuck in recovery mode and prompts me to restore the phone when I connect it to itunes but then I would lose all my data. I DO NOT have any back ups on itunes. Is there anyway to get out of recovery mode without restoring or recover data after a restore?
    Or any other suggestions please? Thanks

    As pdroth said, you should have gotten a backup made when you started the update of iOS. If you cannot find a backup, and the phone is in recovery mode, there are no futher suggestions to make. To get the phone working again you have to restore. You cannot force a backup at this time since it is already in recovery mode. It will not allow anything else but a restore at this point.

  • Am facing issue on my iphone 5s after updating to ios 7.1.1, every while the phone hang after lock it and cannot unlock and even cannot turn on the screen this is so annoying, kindly advice if i have to go back to the store as device still under warranty

    Am facing issue on my iphone 5s after updating to ios 7.1.1, every while the phone hang after lock it and cannot unlock and even cannot turn on the screen this is so annoying, kindly advice if i have to go back to the store as device still under warranty, and if its a hardware issue or software ??

    Hello HaithamOkeely,
    We've an article that provides the following troubleshooting steps that may help stabilize your iPhone.
    If the device is unresponsive or if certain controls aren't working as expected, restart your device.
    If the device remains unresponsive or does not turn on (or power on), reset your device.
    If there is no video or if the screen remains black, verify that the device has enough charge to turn on:
    If you are using an iPad, ensure that it's connected to the USB Power Adapter supplied with the device.
    Let it charge for at least twenty minutes, then see if it starts normally.
    If there is no image on the screen, press the Sleep/Wake button to attempt to wake the device.
    If the screen displays a red battery icon, continue charging the device until the battery is fully charged. Learn more about charging iPhone and iPod touch, or iPad.
    If the above steps do not resolve the issue, or the if the screen remains black or shows a persistent Apple logo, try restoring with iTunes:
    Connect the device to your computer and open iTunes.
    If the device appears in iTunes, select and click Restore on the Summary pane. Learn more aboutrestoring iOS software.
    If the device doesn't appear in iTunes, try to force the device into recovery mode, and then restore it.
    If the above steps do not resolve the issue, contact Apple.
    iOS: Not responding or does not turn on
    http://support.apple.com/kb/TS3281
    Cheers,
    Allen

  • I have an Iphone 4 16gb and updated the IOS 6.1.2. after the update my 3G is not working at all??. can you please suggest what can be done to rectify this problem?

    i have an Iphone 4 16gb and updated the IOS 6.1.2. after the update my 3G is not working at all??. can you please suggest what can be done to rectify this problem?

    I have the same problem.  After updating to 6.1.2 my iPad 3,2 will not find Verizon network.  It just says "Searching..." for ever.  Any thoughts?

  • My Apple TV froze up while updating the software. What should I do?

    My Apple TV froze up while updating the software. What should I do?

    You can't do much else besides pull the plug. If it causes further problems you should be able to restore as below:
    Get yourself a micro USB cable (sold separately), you can restore your Apple TV from iTunes:
    Remove ALL cables from Apple TV. (if you don't you will not see Apple TV in the iTunes Source list)
    Connect the micro USB cable to the Apple TV and to your computer.
    Reconnect the power cable (only for Apple TV 3)
    Open iTunes.
    Select your Apple TV in the Devices list, and then click Restore.
    On the other hand you may be able to simply start the update again. If however the update continues to fail, you should try the restore routine above.

  • I'am using iphone 5 i tried to update the ios 8.0.2 using the shift key in itunes update @ windows 8 i have the file which i downloaded, but it says that firmware version is not compatible. what can i do for it . help me friends

    i'am using iphone 5, i tried to update the ios 8.0.2 using the shift key in itunes update @ windows 8 i have the file which i downloaded, but it says that firmware version is not compatible. what can i do for it . help me friends

    Hello vinoth1986,
    After reviewing your post, I have located an article that can help in this situation. It contains a number of troubleshooting steps and helpful advice concerning update issues:
    If you can't update or restore your iPhone, iPad, or iPod touch
    Thank you for contributing to Apple Support Communities.
    Cheers,
    BobbyD

Maybe you are looking for

  • Error during Post Goods Issue of Material in VL02N for STO Purchase Order

    I am getting one error message during Post goods issue of Material for STO Purchase order. I am doing the Post goods issue in T code VL02N Error is " Account type D is not defined for Document type WL" What is the settings required to be done. Thanks

  • Blackberry PlayBook desktop wont install on pc

    just recieved a playbook for xmas & have tried installing the desktop on laptop in order to sideload apps- which im not even sure what it is. but there is an error that shows up just as its nearly finished can anyonehelp please??

  • Is Apple Certified status worth it?

    Dear All, I am currently working in the broadcast industry and have managed to make the conversion to content editing for internal broadcast requirements. I am in my late twenties so hopefully not an old man to this industry yet I was wondering if Ap

  • Failed to initialize sqlcmd library with error number -2147467259

    I'm trying to get SQL Server to send an email.  The test email works fine; basically DBMail works properly.  The thing is, if a human runs it, everything is fine.  If I schedule it using Sql Server Agent Job, nothing works.  I think this has somethin

  • Adding a lower-third effect - wavy lines with trails plus a titling questio

    Hello All; I saw a cool effect used in a corporate video that I'd like to reproduce. The effect showed a series of lines that moved across the screen in a soryt of curved up/down pattern and then over that was overlaid the title. What is the best and