IPhone Map & Tom Tom iPhone hands-free kit

Hi everyone - can anyone help me with this teaser?
I recently bought a Tom Tom hands-free kit to use my iPhone 4S in my car. I am having trouble with audio... I have been able to connect the phone with the TT unit via Bluetooth, and after talking to the TT help-line, I chose this setting; Settings>General>Accessibility>Incoming Calls>Headset, but I am still having trouble.
The only audio I can hear via the TT speaker is the phone and Siri. All the other audio is either muted (no Music at all!) or else comes over the phone speaker. While it's a reliaf to be able to use the phone 'hands-free' the main reason I bought the unit in the first place was to use the turn-by-turn directions available from the Maps app, and the voice via the phone speaker is too quiet to be audible while I'm driving - does anyone know which settings need tweaking so I can hear the turn-by-turn voice via the TT unit speaker?

I have just spent a few quiet ( ) minutes going through settings, sitting in the car, and can report that the 'Tom Tom Hands Free' option appears both in the Map app and the Music app, but even though I can pop a tick against it, it don't come out of the TT speaker...

Similar Messages

TS3581 Iphone Hands free Kit connection

My Iphone 4S connects to my built in hands free kit in my car via bluetooth but nothing is coming out of the car speakers. I can speak normally through the handset. Can anyone help?

I have just spent a few quiet ( ) minutes going through settings, sitting in the car, and can report that the 'Tom Tom Hands Free' option appears both in the Map app and the Music app, but even though I can pop a tick against it, it don't come out of the TT speaker...

Since updating my Iphone to ios 8, my hands free in the car (Radiosat) is not working correctly. The phone pairs ok with car, and my phone is recognised but then it cuts off the radio and says that I'm in a call, I can't cancel the call or do anyth

Since updating my Iphone to ios 8, my hands free in the car (Radiosat) is not working correctly. The phone pairs ok with car, and my phone is recognised but then it cuts off the radio and says that I'm in a call, I can't cancel the call or do anything. I have taken my car to my local dealer but they say the Radiosat is working ok?

Hello there stidhambr15,
I was researching the issue you are having and recommend a couple of things. First it might be a good idea to reset the device following iPhone, iPad, iPod touch: Turning off and on (restarting) and resetting found here http://support.apple.com/kb/ht1430
Resetting your device
Press and hold the Sleep/Wake button and the Home button together for at least ten seconds, until the Apple logo appears.
If that doesn't quite get the device going again, I recommend restoring the device.
iTunes: Restoring iOS software
http://support.apple.com/kb/ht1414
Might even be a good idea to turn off the phone, reseat the SIM card, and turn it back on.
iPhone and iPad: How to remove the SIM card
http://support.apple.com/kb/ht5163
iPhone 4 (GSM model)
iPhone 4S
Cheers,
Sterling

HT204368 Using iPhone 4S in car for hands-free calling

I am having real trouble using my iPhone 4 S to make hands-free calls from the car. The combined earpiece and microphone I have always used without problem on my Nokia keeps getting silly results with Siri!
I just want to be able to make and receive calls using my Contacts List, and get Siri to recognise my voice when I ask for someone on the Contact list!
If I say I want to speak to 'Stephen Farley' it will come back with 'I don't see Stephen Bali in your contact list'!
Maybe I am doing something wrong?!
Also, will the 'voice regonition' work if Siri isn't working because it's out of contact with the internet?
I just need a simple connnection to my Contact List, without all the fancy options of Siri - which are just a pain!
Any help gratefully received!
I

I have one of those stereos bought from Ebay, no badge, no name, and with multitude of functions,and a mic attached to my visor. Once it is paired with Iphone, all my music and calls go through the car stereo.
for applications that do not direct Audio through BT such as CoPilot (GPS navigation) I connect the Iphone through headset socket and into the stereo AUX input and works great (all sounds, voice,calls) go through it. One disadvantage of this method is that I can't listen to the radio. Well you cannot have it all. Or perhaps there is a Radio application where it plays in the background while I still use my GPS application.

Having trouble using my 9720 connecting to car hands free kit

Hi, i am utterly frustrated with my company blackberry 9720 phone. The trouble i am having is with the car hands free kit, my skoda superb uses the bluetooth premium and cannot use the normal hands free setting like with my Iphone. The problem i am having is firstly connecting, i can only use the bluetooth premuim, which completly changes all the setting on the phone i.e turns the network off on the phone and then a screen pops up saying running SAP mode (must use an ittenna in car?), which in turn stops emails from coming in, i can stupidly write texts messages on my dash board and receive them and read them on my dash board while driving. So when i remove the keys from the ignition the phone does not put the phone back to its normal working settings, it keeps the network switched off i have to go to settings and turn the network on. Thirdly when i turn the car on the phone will not connect automatically it says cannot connect to mobile, but if i switch the phone off and on it automatically connects, but if by the grace of god it does connect an second time the phone crashes and resets and then connects five minutes later after reseting. forthly this is not an phone issue it is definatly software as i have been given an second 9720 and the fault is present on both phones.
can anyone help

as I believe it a car bluetooth hands free can only be paired to one device . ie if you wish to pair with another device you would have to reset back to default and search again.... so does the cuve work if you reset the bury and pair again but then your other phone does not work with it ... this is logical as if we drove down a motorway we would pick up loadsa phones.... therefor we can only pair to one device

Can't connect my bluetoot hands-free kit

Hello,
I can't get my hands-free kit to work. I want to use it with skype or whatever, but when I try to connect it, i've got:
[bluetooth]# connect 0C:E0:E4:3A:D6:ED
Attempting to connect to 0C:E0:E4:3A:D6:ED
[CHG] Device 0C:E0:E4:3A:D6:ED Connected: yes
Failed to connect: org.bluez.Error.NotAvailable
[CHG] Device 0C:E0:E4:3A:D6:ED Connected: no
[bluetooth]# info 0C:E0:E4:3A:D6:ED
Device 0C:E0:E4:3A:D6:ED
Name: PLT_ML20
Alias: PLT_ML20
Class: 0x200404
Icon: audio-card
Paired: yes
Trusted: yes
Blocked: no
Connected: no
LegacyPairing: no
UUID: Headset (00001108-0000-1000-8000-00805f9b34fb)
UUID: Handsfree (0000111e-0000-1000-8000-00805f9b34fb)
I did a manipulation, and I have
`--> sudo modprobe rfcomm
`--> sudo rfcomm bind rfcomm0 0C:E0:E4:3A:D6:ED
`--> ls /dev |grep rfcomm
rfcomm0
But I can't get it to work as an audio device, it still make when I try to connect it:
[bluetooth]# connect 0C:E0:E4:3A:D6:ED
[CHG] Device 0C:E0:E4:3A:D6:ED Connected: yes
[CHG] Device 0C:E0:E4:3A:D6:ED Connected: no
(seen from here:
https://bbs.archlinux.org/viewtopic.php … #p1473242)
what am I doing wrong?
Thanks in advance
ps: It is a plantronics ML20
http://www.plantronics.com/fr/product/ml20
Last edited by Neldar (2014-11-06 20:46:28)

Try unpairing the iPhone 3GS from your Cadillac, then try pairing the iPhone 5 again.
You can find more troubleshooting info in this Apple doc -> iOS: Troubleshooting car stereo connections
Also, iOS 6 uses AVRCP 1.4 so you may need to update the reciever in the car to make it compatible with with all versions of ACRCP.

Hands Free Kits

Has Nokia any plans for new hands free kits, I don't require the extra functionality of the CK-200, just a basic kit along the lines of the CK-7w or CK-100 - both now increasingly difficult (if not impossible) to source at a reasonable price?

I have a similar problem. Renaul Modus iMusic, only 4 months old. Hands free kit with 3GS showed contact names and numbers. iPhone 4 (tried with all iOS versions inc 4.1) pairs and works fine but I see no contacts at all, names or numbers.
Incoming calls work fine and I can manually enter a number and dial fine.
Renault state they use HFP 1.0 and Apple not compliant with this!

HT204387 Can't find my car hands-free kit

Hi, With iphone 5 I can't find my cars hands-free kit when searching bloutooth, but I can find it and pair it easily with my iPhone 3GS. My car is Cadillac SRX 2012

Try unpairing the iPhone 3GS from your Cadillac, then try pairing the iPhone 5 again.
You can find more troubleshooting info in this Apple doc -> iOS: Troubleshooting car stereo connections
Also, iOS 6 uses AVRCP 1.4 so you may need to update the reciever in the car to make it compatible with with all versions of ACRCP.

Missing some voice guidance with hands free kit

I have found that the first few seconds of any voice guidance message is missing when I have my phone connected to my BT hands free kit. This is normally the key bit "in xxx yards turn..." or even the entire speed warning. It doesn't happen using the phone speaker.
I am using the Nokia HF-200 hands free box and the 'problem' has occurred with maps 3.03, 3.04 and 3.06. I have tried my X6-16G (RM-559, V 31.0.004)and a 5230 Navi and both behave the same.
Does anybody know if a different hands free kit would solve the problem, or are they all slow to start up. You don't notice it with calls because the ring tone seems to 'wake up' the HF-200 before the voice message starts.

You're lucky even to get navigation commands via car speakers which defeats the latest Nokia devices with Bluetooth carkits.
Don't want to misinform you but think that CK-300 with CarMenu application upon individual device was one of the few to achieve this but seems development stopped.
Happy to have helped forum with a Support Ratio = 42.5

Hi Guys does anyone know of a way i can get cyclops speed camera alert to work through bluetooth incar hands free kit , i used to be able to connect it via an app called drivesafely but this app is no longer available in apple store ????????????

Hi Guys does anyone know of a way i can get cyclops speed camera alert to work through bluetooth incar hands free kit , i used to be able to connect it via an app called drivesafely but this app is no longer available in apple store ????????????

I think the easiest way to do this is to have the EyeTV app running in one user account and sent via HDMI to the TV, and use a separate user account for Screen Sharing. Both logins can be active at the same time and with Lion you can connect via screen sharing to which ever login you need.
With regards to the Mac video resolution changing, when it is not the current input on your AV receiver. This is 'normal', if the Mac sees no signal it drops down the a lower level. What you need is to buy a HDMI Detective Plus which tricks the Mac in to always seeing a signal and hence it will not drop down the resolution. See http://www.gefen.com/kvm/dproduct.jsp?prod_id=8005
The Mac mini does have an IR receiver. This can be used with the EyeTV app, iTunes, and similar. Yes I believe EyeTV would run for prolonged periods quite happily, it is has been around for a long time and had most of the rough edges polished off. However one issue you will have to deal with is that it does not automatically update its program guide data. For this you might have to write or modify an AppleScript. Elgato support or their user forums will be a lot of help.
You can set EyeTV to convert recordings to an iTunes (Apple TV) compatible format and then delete them from EyeTV.
The HDMI Detective should solve your handshaking problems.

Bluetooth: 8310 won't complete pairing with hands-free kit in 2006 X-type Jaguar

My new 8310, v4.2.2.181 (Platform 2.5.0.35), recognises the hands-free kit in our 2006 Jaguar X-type ("Jaguar" shows on the Bluetooth paired devices screen), but the pairing won't complete through to connection. Our dealer has confirmed that other phones will. The Jag website confirms full compatibility with the 8310 to v4.2.2.146 (Platform 2.5.0.16), also "Latest Tested Version". I'm asking Jaguar what the latter is. But is there anything simple that I'm getting wrong here? I've read the trouble-shooting pages in the manuals for the 8310 and the car, have tried disabling the encryption, and changed the "trust" option to Yes. No result so far: help!

for DVD:
which DE you use ?
post your
/etc/fstab

Parrot Hands-free kit and 6300

Having a bit of trouble with my new Parrot PMK5800 hands-free kit and my 6300. I can connect to the 2 together, but the Parrot asks for a voice tag from the 6300 for hands free dialling. I cannot seem to be able to transfer this. Have tried most things but no success. Any help ???

Hello,
The Blackberry 8310 is fully compatible with the Parrot 3200 LS and phone book synchronisation is supported between these two devices. The revolving circle means the phone book is being downloaded, which could go on for a very long time depending on the size of your phone book. Check your phone book does not exceed the maximum number of contacts permitted by the Parrot.
Total Car Kits
http://www.totalcarkits.co.uk
Hands Free Car Kits

Using laptop as hands free kit

I can connect to my laptop via bluetooth and use Nokia PC Suite. How can I use my laptop's speaker & mic. as a hands free kit?

25-Jun-200701:36 PM
richmitch wrote:
Hi there, did u ever figure this out? After all my searching you're the nearest match. I can only find software that allows you to send SMS from your PDA (bluetoothed to your mobile). have also found some Dialer software but that just dials your phone from your PDA and that' it.
I'll dig the links out if you're interested? let me know if you get the handsfree sussed out.
cheers
Rich
I saw this kind of software yesterday on a car navigator myguide 3300 and it was pretty cool and I want to find something like that fot PDA too.

New user with query about hands free kit

Hi, new user to the forum so please bear with me.
I have recently got a Nokia 6303 Classic 'phone and was thinking about buying a CK-100 hands free unit.
Questions are:
1/ Are they compatible?
2/ Do you have to use the external speaker supplied or can you use the car stero's speakers?
3/ Is the hands free unit easy to fit?
4/ Does the hands free unit automatically mute the car stero, or, is it necessary to buy a piece of equipment to do this?
5/ When fitting the hands free kit do any other connectors have to be brought to connect to the car stero? If so, are they readilly available?
The car the kit would be fitted into is a Mondeo ST220 with standard Sony 6 CD head unit.
Thank you - Steve

The issue was all around Mobilme syncs and the solution to stop duplicates by choosing "all contacts" solved the problem here.

Iphone with Parrot 3200 LS Hands Free Car kit: photos for contacts?

Hello,
Is anyone else using the Parrot 3200 LS hands free car kit with your iphone? I have one, and so for it's been great, but I can't figure out how to get the photos associated with my contacts to transfer to the contacts in the Parrot unit. It synced the contacts no problem, just no photos with them. Has anyone been able to get their photos to come up on the parrot unit? How?
Thanks,
Dana

I have had the 3200 LS for 3 months. I havn't seen the photos transfer. Either my Parrot or my iphone does not work right. They will work showing my address book for two or three days then they will not pair for 3 or 4 weeks. I'm in one of those not pairing periods now. The grey symbol is lit. Under bluetooth it shows that they are paired but they don't work. Anyone got any ideas? I'll try working on the photos the next time it decides to work.

IPhone Map & Tom Tom iPhone hands-free kit

Similar Messages

Maybe you are looking for