Iphone menu button not working takes several clicks to change menu

I can push on off button, and keep pushing menu button and will finally change, but doesn't just click to change anymore. Just started this today, I just got the phone when verizon came out with it in Feb. so is still new. What can I do?

Just happened or ? I found this in iphone manual :
If something isn’t working right, try restarting iPhone, force quitting an app, or resetting iPhone.
Restart iPhone:
Press and hold the On/Off Sleep/Wake button until the red slider appears. Slide your finger across the slider to turn off iPhone. To turn iPhone back on, press and hold the On/Off Sleep/Wake button until the Apple logo appears.

Similar Messages

My speakers from my iPhone 4S is not working I'm clicking on the buttons on the side nd the volume is not even showing getting louder or lower but when I plug in my ear phones I can hear it juss happen out of no where what sould I do ?

My speakers from my iPhone 4S is not working I'm clicking on the buttons on the side nd the volume is not even showing getting louder or lower but when I plug in my ear phones I can hear it juss happen out of no where what sould I do ?

Your iPhone charging port may have a minor short, causing iPhone to falsely sense it is connected to a dock turning off its speaker. Clean iPhone charging port with a clean dry toothbrush.

Title & Menu Buttons not working correctly on remote control/ set top player but work in preview.

Title & Menu Buttons not working correctly on remote control/ set top player but work in encore preview. This only happens for a Blu ray project. When a user presses the menu button it should go to the previous menu they were on but it goes to the main menu. When they press the title button they should go to the main menu but it doesn't do anything. My DVD projects work as expected.I've tried creating a new "test" project with different footage and still get the same undesirable results.
Overrides grayed out and set to "not set" for timelines and menus.Project settings and build are set to blu ray. Also I've noticed when I preview a Bluray project the preview window shows a red colored disc next to the Title button when viewing the timelines and green when playing the menus but not so for a DVD project it displays red if motion menus and or timelines are not rendered/encoded. I'm not using motion menus and all the media is encoded according to the project specs.
I've searched this forum but couldn't find the answer. Any help or redirects to a solution would be appreciated. Working with CS5. Thanks.

I found out on my Samsung Blu ray player the remote has a tools button on it that brings up audio, angle, chapter selection etc.and also title selection which is actually the menus and the timelines unfortunately. It's not as easy or direct as last menu selected but it's a workaround at least. I also plan on using a pop up menu. I'll let you know.

How to fix the iphone home button not working?

how to fix the iphone home button not working?

Temporary Solution: Settings > General > Accessibility > (turn on) Assistive Touch
This will enable a "Home" button on the touch screen. (iOS5+)

As i have written,my iphone home button not working

as i have written,my iphone home button not working.i talk to cusmer care & also visit to care center in delhi. but they say to pay full mobile payment to repair it.
this mobile is onle 11 month old. the case id number for this call was: 325468510.

OK, thanks for sharing that information. Now, what it is you would like us, your fellow users and the only people who will reply to you here, to help you with? If you are expecting a reply from anyone who works for Apple here, you will not get such a reply. The only way to discuss any issue with Apple is to call them:
http://www.apple.com/in/support/iphone/contact/
Regards.

Sub menu buttons not working on mobiles

Why are my sub menu buttons not working on mobile phones but working fine on computers?
Sub menu buttons come under these buttons, Our funerals services, Advice and information.
http://www.vanessaroberts.co.uk/

You are using a Spry menubar widget. Spry was created pre-touch-screen systems and hence not designed for touch screens.
There are a number of solutions available to you
1. Don't have an active link on the main menu item
2. Place submenus in the page that is opened by the main menu item, e.g. as a vertical menu
3. Use Spry Menu Bar ver 2.0
3. Use a different menu system that is geared to accommodate touch screens
Because of the demise of Spry, see here http://blogs.adobe.com/dreamweaver/2012/08/update-on-adobe-spry-framework-availability.htm l, option 3 looks like the best option.
There are a number of free-of-charge jQuery menubars, you could also opt for one of the commercial menubars such as PVII, WebAssist or DMXZone

Menu button not working

I've got a 6gb mini, had it since Sept 05. Yesterday the menu button stopped working, so I can't choose what music it plays, it only plays on shuffle as I can't get back up. I haven't done anything to it so I wondered what to do. I got my iPod in the US but I live in the UK. I bought the Applecare Protection Plan when I got it but forgot to enroll it, so I don't know if it's still valid. It should still be covered under the protection but I don't know if I've left it too late to register it. What do I do?

If doing a Restore and reset do not help, very likely a hardware issue
In case your iPod is no longer covered by the warranty and you want to find a second repairing company, you can try iPodResQ at your own risk
http://www.ipodresq.com/index.php

Layered Menu Buttons not working on DVD player

Hello,
I just made an SD DVD with several layered menus. The backgrounds for the menus come from photoshop files with different layers for normal, selected, and active states. Navigating the main menu works fine in the simulator and when I play the disc in my computer, however, I can not arrow to another button on dvd players. I have made several discs this way and this is the first time I have had this problem. My burn process is to make an image and then burn the image in toast. Any thought?
-Brian

Hi Brian - welcome.
Layered menus are particularly tricky... they almost always require two actions from the user to get them working in a player. One click to land on the button and another to select it. This is really frustrating at times, but is down to the way the layered menus work.
You can convert them to standard menus pretty easily though, and unless you absolutely need to have different layers I'd strongly advise that you do convert them. Standard overlay type menus work with a rollover type of effect, allow you to have an audio bed and work far faster on DVD players.
The only time I'd stick with layers is when the selected state reveals a further piece of information that takes up most of the menu area. In all other cases I'd avoid them if I were you

IPhone Home Button not working after upgrade to ios 5.1.1

Hey everyone,
I'm pretty sure this is a software failure due to the symtoms the iPhone is showing;
0 - the home button does not work at all when the phone is turned on and running ios 5.1.1, well it used to work okay when i had ios 5.0.1, I upgraded to 5.1.0 and started working randomly, upgraded to 5.1.1 to see if it was fixed with no luck at all.
1 - When locked the screen does sometime light up, like when you press the home button and don't slide the unlock button. but it does not exit apps anytime, I mean it doesn't act like it's pressing the home button randomly but only when the phone is locked.
2- The button does work perfectly when iOS is not running: I can get in and get out of recovery and dfu mode at will, that wouldn't be possible if the button were broke.
3- what else? Oh yea, not really a symtom: Tried the 'home button calibration' several times.
4 - It's not filthy, since I really cleaned it thoroughly with a powerful tiny nozed air blower I got and gave a rubbing alcohol treatment too.
5 - when I shut the phone down it instantly turns back on, I can interrupt the turning on for turning the phone into dfu mode (i'm sure It's in DFU mode because the tinyumbrella log monitor tells me)
I'm now using the 'soft' home button that goes in the accesibility options, but hey, I didn't pay a ton of money for a phone that the same Apple is gonna break down.
It's out of warranty and I don't have apple stores where I live.
I'd downgrade to 5.0.1 in a snap if I could but I'm not into jailbreaking, so the shsh blob thingie is not a possibility.
Any apple dev around that can give me a workaround?
thanks a lot in advance
Added more info ~

I had the same problem with Home button not responding after upgrading from iOS 5.1 to iOS 5.1.1 on an iPhone4.   I solved it but not sure exactly what fixed it.   Here is what I did.
1. Took it local Apple store Genius appointment.   They used a special tool and took some lint out of the connector opening.   The Home button started working.   They said even though the phone was out of warranty, I could buy a new replacement one without a contract for $150.
2.   The Home button stopped working when I got home.   I got some compressed air in a can and blew the air through the connector to try and clean out more dust.   I now keep the phone with the connector opening facing down in my pocket.   I also struck the phone downward on my hand or other soft surface to force as much dust out as possible.
3. The Home button still was intermittent. I then tried to do a hard reset by holding the power on key and the Home button simultaneously for about 10 seconds. This doesn't work if the Home button doesn't respond.
4. I connected the iphone to Itunes via the USB to sync the phone. While connected, I did a Hard Reset by Holding the Power button and Home button simultaneously. I noticed the Home button responded better when connected to ITUNES via the USB.
5. I did a backup of the iphone4 by highlighting the iphone 4 while connected to ITunes and right mouse click and selecting BACKUP.    I was prepared to reset my phone4 in iTUNES and restore it from the backup.
The phone worked consistently before I had to do this.
6. As a last resort which I didn't need to do, I was going to copy all my settings for the iphone by selecting the phone in iTUNES and looking at all the sync settings.   I would then have restored the iphone to original factory settings and then sync the phone using the copied settings. This would have made sure that the backup didn't include the bug.
Fortunately, I didn't have to do step 5 and 6.   Things started working after Step 4. So I don't really know if it was the iOS 5.1.1 upgrade or pure coincidence that the Home button stopped working immediately after the upgrade.

Menu buttons not working in Apple DVD Player

I am having a real problem. I have a menu with three buttons. The default button takes you either of the other buttons (depending on whether you press right or down on the remote). These two buttons are auto-action and proceed imediately to other tracks. This works perfectly in home DVD players and in the Apple DVD Player using the "remote". Howver, if I try clicking the buttons using a mouse on the Apple DVD Player window, they DO NOT work! I have buttns over video on the same disc and these work perfectly by clicing on them with the mouse. Has anyone else had a problem like this and if so, have you found a solution? Many thanks!

Is the one that doesn't work a layered menu? DVD Player does not work correctly with layered menus, it takes one click to switch to the selected state, and a second click to activate the button.

Simple Drop Down Menu buttons not working

I'm having a bit of trouble getting a button in a hoover over drop down menu to link to another scene in the .swf movie. I just doing a basic drop down menu (example here: http://www.flashkit.com/tutorials/Interactivity/Navigation/Drop_dow-Phlook-951/index.php) with a couple of buttons with in a movie clip, the movie clip being the "button" someone hoovers over. The buttons however are not going to the corrisponding scene I have them set up to. What's strange is that if I set in the buttons action panel to go to an url instead of a scene, in the .swf movie the button works when I click it...it wants to go the specificed url. Nothing happens when it's set to go to a scene. Any help would be much appreciated.

Thanks for the reply Ned. The code I'm using on the buttons is the same method I'm using for the regular buttons (i.e. not with in a movie clip).
on (release) {
gotoAndPlay("Scene X", 1);
I like and appreciate the idea on keeping it with in the same timeline, but that didn't work either. This is all very strange, because as I said, the buttons that are not with in a movie clip work with that method in their action panel. And the buttons with in the movie clip work out to an url, just not a scene or frame number.
I'm using CS4, but I'm not sure which 'Publish' settings I should have it at, and on 'Profile' it's set to 'Flash CS3 Settings (it's either that or 'Flash 5 Settings').

Menu button not working on iphone4

The lower menu button has stopped working on the iphone 4. Anyway to fix it or do we have to buy a new phone?

"I can't do the manual reboot as that requires you to be able to press menu which I can't do."
Are you sure? Have to actually tried holding the MENU and SELECT buttons to reset it? Sometimes this works even though the menu button doesn't appear to work otherwise.
If it's not working though, you might try restoring it.
http://docs.info.apple.com/article.html?artnum=60983
Cheers!
-Bryan

Interactive Reports Action Menu buttons not working

We are running Apex 4.02 and using theme 11 (round green). We recently upgraded to IE 10 (on windows server 2008 R2) and are now experiencing issues with all interactive reports within Apex. The Action menu is displayed correctly and the options are available but the buttons to apply the changes do not seem to respond.
For example, I can press the Action button then select Format->Sort from the actions menu. The sort by options are displayed but nothing happens when I press the Cancel or Apply buttons. There is no error - it looks like the button press is not executing the code.
I have searched for issues specifically related to Apex but have only been able to find references to general problems with IE 10 and Ajax calls. I'm not sure whether IRs are using Ajax as part of it's core functionality and whether this is the behaviour we are seeing.
I'm keen to understand whether others have encountered this problem and resolved the issue somehow. Any help would be very much appreciated.

I would have set this up somewhat differently. I'd have all of your buttons set to pause the slide in exactly the same spot about 1.5 seconds into the slide. To set the variable for completion of a section I would have used a standard or conditional action that was executed by the button that brings the learner back to the menu slide. This action would set the variable and then jump back to the menu slide using the button's On Success action. You need one of these actions per separate section in your project.
As to why some of your buttons are not working at all...
1. They may not be set up correctly. Check all settings again.
2. The buttons may be corrupted. Delete the ones that don't work and insert new ones. Avoid copying and pasting.
As luck would have it, I've just completed an e-book Guide to Adobe Captivate Advanced Actions that has an entire series of practice exercises that take you step by step through creating exactly the menu slide setup that you describe. If this project is important enough to you, it may be worth your while to consider purchasing that e-book:
http://www.infosemantics.com.au/adobe-captivate-advanced-actions

Menu button not working on ipod

My ipod isn't happy... It's a 4th generation 20gb click wheel model and I've had it for about 6 months. For some reason on the click wheel the 'menu' button will not react when I try and press it which means I am pretty much stuck for navigating around my ipod. I can't do the manual reboot as that requires you to be able to press menu which I can't do. Any ideas?

"I can't do the manual reboot as that requires you to be able to press menu which I can't do."
Are you sure? Have to actually tried holding the MENU and SELECT buttons to reset it? Sometimes this works even though the menu button doesn't appear to work otherwise.
If it's not working though, you might try restoring it.
http://docs.info.apple.com/article.html?artnum=60983
Cheers!
-Bryan

Layered menu buttons not working when built.

I have a project that has one menu and one track. The menu has 7 buttons linked to 7 different markers in the track. When I run the simulation in DVD SP, the buttons link fine, and play as they should...but when I build the project and run it in DVD player or burn it to a disk, the buttons do not work.
If I create a non-layered menu, the buttons will work when built...
I feel like i'm just missing one little setting on the layered menu
Thanks
Mac OS X (10.4.8)

Don't forget that a layered menu will normally need two presses to get anything to happen, one to select the button and the second to activate it.
That said, are you sure that you have got the psd file set up correctly? I would recommend using a background layer with everything on it that you want to appear when not selected, then only adding layers with the changes necessary to show the button selection/activation.

Iphone menu button not working takes several clicks to change menu

Similar Messages

Maybe you are looking for