Iphone5 turns off after latest update and resets when turned back on

Does this happen to anyone else?  Any ideas as to a cure?

Restore as new, if the problem continues take it to Apple for evaluation and possible replacement.

Similar Messages

  • I updated the IPAD with the latest update and now when I turned the IPAD on, I get the itunes logo and then nothing else.  How can I fix this to let me use my IPAD?

    I updated the IPAD with the latest update and now when I turned the IPAD on, I get the itunes logo and then nothing else.  How can I fix this to let me use my IPAD?

    YOU ARE IN RECOVERY MODE
    1. Turn off iPad
    2. Turn on computer and launch iTunes (make sure you have the latest version of iTune)
    3. Plug USB cable into computer's USB port
    4. Hold Home button down and plug the other end of cable into docking port.
    DO NOT RELEASE BUTTON until you see picture of iTunes and plug
    5. Release Home button.
    ON COMPUTER
    6. iTunes has detected iPad in recovery mode. You must restore this iPad before it can be used with iTunes.
    7. Select "Restore iPad"...
    Note:
    1. Data will be lost if you do not have backup
    2. You must follow step 1 to step 4 VERY CLOSELY.
    3. Repeat the process if necessary.

  • I updated the IPAD with the latest update and now when I turned on and I get the Itunes log and nothing elser

    I updated the IPAD with the latest update and now when I turned the IPAD on, I get the itunes logo and then nothing else.  How can I fix this to let me use my IPAD?

    Hi ....
    "I get the itunes logo and then nothing else"
    Use Recovery Mode >  If you can't update or restore your iPhone, iPad, or iPod touch

  • Ipod sync is greyed out after latest update and libary was wiped

    i updated the latest update...2 weeks later opened itunes my libary was gone bar itunes purchases...
    now when ipod is connected if i go to file/ devices ipod isnt there eg bla blas ipod and the sync is greyed out ..
    now before i updated the latest update all was fine..
    ive since put my libary back as is stored on external hard drive and reset ipod and added libary back to ipod
    but still the same as dicribed above.
    now i connected my wifes iphone 4s to itunes went to file/devices hey presto itunes reconised it as eg wifes iphone
    but dosnt do for ipod..
    any ideas cheers.

    Normally a greyed out Wifi is a hardware failure, but with some of the problems I've seen with the upgrade to iOS 4 on 3G phones, I'm not convinced the problem/problems aren't related to software. I have two suggestions, neither of which are guaranteed to work: 1. Restore your phone as a "new" device in itunes & not from backup. But first delete any and all .ipsw files on your computer. This will force itunes to re-download the current OS. The .ipsw file can be found here:
    OS X: ~/Library/iTunes/iPhone Software Updates
    XP: C:\Documents and Settingsusername\Application Data\Apple Computer\iTunes\iPhone Software Updates
    7 & Vista: C:\Usersusername\AppData\Roaming\Apple Computer\iTunes\iPhone Software Updates
    You may have to turn on "show all hidden files" to find them.
    Once done, reboot your computer, launch itunes, connect your phone & restore as "new". When finished, DO NOT SYNC, rather eject your phone & see if all is working properly. If it is, sync your content back to your phone. If not, proceed AT YOUR OWN RISK!
    2. Try and downgrade to 3.1.3 from here:
    http://www.felixbruns.de/iPod/firmware/
    Note: Before you try this, bear in mind this is NOT endorsed by Apple & that you run the risk of making your phone inoperable.

  • Error message after latest update and backup, can't operate program at all, no customer service.  LR 5.5, Windows 8.1

    I updated to LR 5.5 and later restarted my computer.  I didn't use the program for a few days and then when I did, it wanted to backup the catalog.  I agreed and closed the program.  The next time I opened it, it asked me for my region, saying it was required.  When I answered, I got an error message saying it has encountered an error reading the preview cache and needs to quit.  It fails to fix the error and gives the same message over and over.  I can't use the program at all.  Customer service has apparently been discontinued and I'm really at the end of my rope with this whole company.  I don't think I've ever had a mass-release program with so many problems.

    open disk utility, make sure that you're back to only 1 partition should be 'macintosh hd' unless you renamed it
    do not try to use the disk, instead DL the x64 8.1 pro ISO from this link, and once it is finished, then open bca and choose all 3 options (copy iso, copy windows support and install windows)
    http://getintopc.com/softwares/operating-systems/windows-8-1-download/

  • HP Slate 21 audio issue after KitKat update and reset

    I have upgraded my HP Slate 21 from JB to KK. Now the sound quality is very bad!
    I came directly from xxx.11 kernel and made factory reset but didn't get a good result. Please how can I fix this tremendous issue?

    Hey @PauloTxR ,
    Welcome to the HP forums.
    I understand you're experiencing issues with sound quality on your Slate 21 PC.
    Please review the following thread: HP Slate 21 Kit Kat OTA Update Fix for Audio Quality and LAN Connectivity.
    This fix will resolve audio issues of a software nature resulting in the KitKat update. If your issue persists after applying the specific update mentioned in this thread and have done a factory reset, the issue is likely hardware related and not the result of the KitKat update.
    If you have done the above and continue to have problems please call our technical support at 800-474-6836. If you live outside the US/Canada Region, please click the following link to get the support number for your region: Phone Assist Worldwide.
    Thanks.
    Please click the "Kudos, Thumbs Up" at the bottom of this post if you want to say "Thanks" for helping!
    Please click "Accept as Solution" if you feel my post solved your issue, it will help others find the solution.
    The Great Deku Tree
    I work on behalf of HP.

  • When i add text to PDFs and work on the file for awhile, my red added text starts to turn into red X's with a box around them. I have OCRs turned off, i have the latest update, and i have registered the product. What is happening to my text while i'm work

    When i add text to PDFs and work on the file for awhile, my red added text starts to turn into red X's with a box around them. I have OCRs turned off, i have the latest update, and i have registered the product. What is happening to my text while i'm working on these files? On top of this, my red arrows get moved around also.

    Hi ,
    Could you please update me with few details like what version of Acrobat are you using?
    What OS do you work on ?
    Do you experience this any particular PDF or happens with all of them?
    Did you try the same with turning on the OCR ?Please check the same and compare the outputs .Does that help you in anyway ?
    If the file is not confidential ,could you please share the file with us so that we can analyse it our end and revert you with the appropriate answer .
    Please share the file on [email protected] and please cc [email protected] as well .
    Regards
    Sukrit Dhingra

  • HT201304 I updated my ipad mini to ios7 and after that the restrictions have been turned on automatically. It was off before the update and I din do after either. I tried 1234 but it doesn't work. Please help me.

    I updated my ipad mini to ios7 and after that the restrictions have been turned on automatically. It was off before the update and I din do after either. I tried 1234 but it doesn't work. Please help me.

    1. It is never a good idea to include personal info like your email address or Apple ID in a post on an open forum.
    2. The email you received DOES NOT say your Apple ID cannot be used to unlock this iPad. The email informs you that your Apple ID was used to unlock an iPad. Fortunately the iPad is yours. The message confirms that. If your Apple ID was used to unlock an iPad that was not yours your would then know to change your password. Since the iPad is yours you do not need to change your password.
    Is your iPad working?

  • HT201210 After latest update my iPad (no camera) screen went dark (dim) & blank. Once voice said setup incomplete. Tried reset does nothing. Home screen/wifi setup appeared for moment. Hear swipe see nothing!HELP

    After latest update my iPad (no camera) screen went dark (dim) & blank. At first I could not power off. At some point voice said setup incomplete. In every language. Took someones advise turned off voice over in itunes.. that stopped the voices. itunes identifies and syncs but ipad screen remains blank (dimly lit). Home screen appeared for moment couple of times as well as wifi setup but disappeared as soon as i started to enter info. Hear swipe see nothing! HELP!

    adetoye50 wrote:
    Dear Contacts Journal Support Team,
    FYI, this is a user to user support forum.  You are NOT addressing Apple here.
    Honestly, I doubt anyone is really going to take the time to read the novel you have written.

  • HT201210 my phone was unable to finish the latest update and gone into recovery mode. will only restore if i do a factory reset, but i dont wanna lose my photo/videos!!!

    my phone was unable to finish the latest update and gone into recovery mode. will only restore if i do a factory reset, but i dont wanna lose my photo/videos!!! how can i back up up before i restore it. im not able to acces my phone normaly, stuck in recovery or something.

    it seemed to have backed up everything just before the software update 6.1.4. so after the full restore i restored from backup and its all still there (mostly)
    what a relieve...thx

  • Impossible problem after latest update of 10.5 and 10.6

    Hi all,
    I've an incredible problem that I'm not able to solve...:
    after latest update of 10.5 (some days before SL) I noticed that mouse movement was very strange and every 10 seconds (about) the mouse acceleration speeds up and after 1 seconds turn normal. The problem repeat in infinite cycle. With 10.6 and 10.6.1 is the same.
    I made also this test: I boot with Leopard DVD and tested the mouse movement on the install screen. The movement is ok but if I boot with Snow Leopard DVD the mouse movement on the install screen is wrong.
    Then... this is not a problem of a software on my hard disk (my first suspect) but some difference on the driver of the mouse that on my iMac has this problem.
    Someone can help me?
    Thank you all

    faabri
    What kind of mouse are you using?
    EDIT: I just saw your other post here . . .
    You should include all the detail in your post here, so that
    people can help you with as many facts as possible.
    Message was edited by: ~Bee

  • My ipod keeps showing the apple logo on and off after i updated it?

    my ipod keeps showing the apple logo on and off after i updated it?

    Try:
    - iOS: Not responding or does not turn on
    - Also try DFU mode after try recovery mode
    How to put iPod touch / iPhone into DFU mode « Karthik's scribblings
    - If not successful and you can't fully turn the iOS device fully off, let the battery fully drain. After charging for an least an hour try the above again.
    - Try on another computer                            
    - If still not successful that usually indicates a hardware problem and an appointment at the Genius Bar of an Apple store is in order.
      Apple Retail Store - Genius Bar              

  • Why can't I open iTunes or apps on ipad1? And why do apple not support the latest update for ipad1 when it's less than 2 years old. I am sick of huge corporations ripping off joe public!

    Why can't I open iTunes or apps on ipad1? And why do apple not support the latest update for ipad1 when it's less than 2 years old. I am sick of huge corporations ripping off joe public!

    And the processor limitations.
    iPad: RAM - 256MB, Processor - 1 GHz Apple A4
    iPad 2: RAM - 512MB, Processor - 1GHz dual-core Apple A5
    iPad 3: RAM 1024MB, Processor - 1GHz dual-core Apple A5X
    Similarily, the iPad 2 did not get Siri and some other features in iOS 6.
     Cheers, Tom

  • I can't share a song i created in garageband to iCloud using iPhone 6. I have all the latest updates and i have iCloud drive enabled and turned on as well as sharing through garage band

    I can't share a song i created in garageband to iCloud using iPhone 6. I have all the latest updates and i have iCloud drive enabled and turned on as well as sharing through garage band turned on. The option to share to iCloud just doesn't appear. Also, everything on my macbook is up to date and iCloud options are all turned on.

    Have you enabled iCloud in the Settings for GarageBand on your iPhone?  See this page:  http://help.apple.com/garageband/iphone/2.0/index.html#chsdfe5c2c2
    Turn on iCloud for GarageBand
    You turn on iCloud for GarageBand in the Settings app on your device.
    Close GarageBand.
    On the Home screen, tap Settings, then tap General.
    Tap GarageBand.You might have to scroll down to see the GarageBand icon.
    If the Use iCloud switch is not turned on, tap it.

  • My brand new iphone 4gs from Sprints, is turning off whenever it wants and does not come back after 2 or 3 hours???,

    My brand new iphone 4gs from Sprints, is turning off whenever it wants and does not come back after 2 or 3 hours???

    Return it for a warranty replacement.

Maybe you are looking for

  • How do I synchroniz​e my instrument​s output at the same time?

    Hello: I am using Labview to control a New Era Pump Systems automatic syringe pump and to record diameter measurements from a LaserMike optical comparator. My program is fully functional, the code is attached with all auxilliary files in the NE-50X f

  • Oracle bi error codes u9kp7q94 OBIEE 10g

    Hi All, I have created new user in RPD(Online Mode). Then i have loged into Answer.It throws error "oracle bi error codes u9kp7q94 OBIEE 10g" How to fix. Thanks Gram

  • Time Capsule disk cannot be mounted

    I use Time Machine to back up wirelessly to a 1TB Time Capsule. This has worked flawlessly until recently. (I bought the TC in late August 2008.) Now, I get an error message that the backup disk cannot be mounted. I cannot see the TC disk in Disk Uti

  • 500 SAP Internal Server Error, in WD report while launching SC in SRM 7.01

    Dear SAP WD Gurus, We have recently upgraded the SRM 7.0 to EHP1 after that we are getting ths below We have created Z WD application genarating report in SRM 7.0, we have provided a hytep link in row to display shopping cart in the report. on click

  • IPod won't format, won't be recognized by iTunes

    Okay so my problem involves a lot of history so let me give you the background information. I first got my iPod a year and a 1/2 ago and it worked just fine I was very happy with it and never had any problems. I set mine up as a harddrive so I could