IPhoto 09 rebuild stuck Examining Library with progress bar unmoved

It has just sat there for 2+ hours The activity monitor shows iphoto is very busy. Should I keep waiting?
Problem occurred when iphoto was opened (and it worked fine three days ago) and it told us that the library was busy of needed to be rebuilt. Reboot of imac didn't help.

I have made a copy of a week-ago version from time machine. She has added no phtots since then.
To add to léonie's response the library must be restored as follows from within the Time Machine application:
OT

Similar Messages

Ipad 2 ios 8 update stuck on Apple with progress bar

Hello,
I'm from Paris and I didn't find any solution around me.
So, I hope you'll help me to find something. Sorry in advance for mistakes. My english isn't perfect.
Yesterday, I tried to update my Ipad 2 to iOS 8 in OTA way.
Everything was going fine until the Ipad rebooted. Since this step, the Ipad stucks on the famous Apple with a progress bar under. The progress bar is 30% filled.
I tried to put my Ipad in DFU mode and it doesn't works.
The Ipad switch off few seconds and it switch on back in the state describes before.
Could you please heeeeeelp me.

i have the same problem, my ipad 2 ios 8 update: stuck with apple logo refreshing every 2 minutes or so with the black screen (like the one for boot up or reset) but not turning on or connecting to itunes. plugged it in to the computer for an itunes connect to do a hard reboot and the device shows up in grey (meaning i cannot click on it) for a minute while the ipad cycles with the apple logo. the device showing in itunes then disappears and the whole cycle starts over and over again. yes, please help!
update: ok so another member suggested this and it is working so far, although my data will be lost...it is what it is:
DiavonexFeb 5, 2014 9:46 PM Re: Unable to start my Ipad 2 after upgrading to Ios 7.04 . The screen is stuck with the start up apple logo till full discharge. Please help.
Re: Unable to start my Ipad 2 after upgrading to Ios 7.04 . The screen is stuck with the start up apple logo till full discharge. Please help.in response to Pratik Nayak
FORCE IPAD INTO RECOVERY MODE
1. Turn off iPad
2. Turn on computer and launch iTune (make sure you have the latest version of iTune)
3. Plug USB cable into computer's USB port
4. Hold Home button down and plug the other end of cable into docking port. Do not release button until you see picture of iTune and plug (very important)
5. Release Home button.
ON COMPUTER
6. iTune has detected iPad in recovery mode. You must restore this iPad before it can be used with iTune.
7. Select "Restore iPad"...
Note: Data will be lost

Splash screen with progress bar and multiple jar files to load

Hello,
I have been looking to the new features in java 6 for splash screens. I haven't implemented this never before and i was wondering how i could do the following with java 1.5 or 6:
I would like to see a splash screen with a progress bar that "grows" when every jar file has been read.
At this time i call my application like this from a shell script:
exec "$JAVA_BIN" -Djava.library.path=$LIBRARIES_J3D -classpath xxxx.jar yyyy.jar zzzz.jar ...
where xxx.jar, yyy.jar and zzz.jar are very heavy jars.
So i would like to see in the progress bar 33% 66% and 100% when they are loaded.
I do not know if this is the right forum to ask for this. If no, please point me which would be the ideal one.
Any help will be very useful. Thanks to all!

Am 10.07.2015 um 07:17 schrieb Lalit Solanki:
> Hi friend,
>
> I am create pure eclipse E4 application and trying to splash screen with progress bar and message.
>
>
>
>
> but above image in only support eclipse E3 application so pleas help me how to add progress bar and message in eclipse E4 application
>
Hi Lalit,
there's a Bug entry: https://bugs.eclipse.org/bugs/show_bug.cgi?id=382224
Meanwhile you can use this solution:
https://www.eclipse.org/forums/index.php/t/328812/5ceed4bcaa683a94d65efb161bffd217/
Regards,
Ralf.

Macbook opens slowly with progress bar below the logo

macbook opens slowly with progress bar below the logo, what's happened can it be fixed and how Yosemite OS
Thanks

The status bar below the Apple logo in Yosemite is not a bug, its a feature. No need for a fix.
The reason why your MB starts slowly shall be answered if we have more info on your MacBook (RAM, version, etc.)

Gray Boot Screen with progress bar & SMC Issues

Hi All,
Over the last few days I've experienced the grey boot screen with progress bar three separate times after the finder froze and I was forced to manually reboot my imac. Previously I have only seen this during a Firmware update.
I am also concerned about the Finder freezing. It has been happening when I've been trying to access any of my external hard drives at random intervals (connected via usb, and f800). I am concered that my SMC controller might be failing as these drives are testing fine on other computers and in drive test programs. Also, the f800 drives have been self unmounting.
I had my internal drive replaced by apple a few weeks ago, could they have somehow damaged the smc controller unintentially? Or is this simply a Snow Leopard hiccup? (I'm running 10.6.2). I'm really starting to get annoyed with having to hard reboot or constantly reset my SMC. Any ideas before I take it in to a store?
Thanks!
Message was edited by: fkick1

I have found other users have this same problem when using windows. My setup worked fine until I did a windows update. Now apple partition is inaccessible. Guess the windows update whacked the apple partition. Apple should have a workaround. Bad Windows!

CS3 install silent with progress bar ??

Is it possible to install full CS3 with progress bar showing when the program silently installs?
Install works fine using UI mode Silent and Full, but I can't find andy other options?
My problem is when using the silent install of full CS3, shortcuts are available before the installation is finished. Since the installation takes time, users may click the shortcut before the installation is finished, resulting installation fails.
Using the UI Mode Full is dependent on the users, and not accepted by company.
-Odesti

We too are in the same boat, we need a progress bar so that our users know that we are deploying the application.
I've tried various random switch for the "UI mode" but none work. There must be others than silent or Full.
Phil H

How to associate audio file with progress bar

Hi all,
I have a case in which I need to associate an audio file witha progress bar. What I want to do is to able to play a audio file which will say " Process started.." Process going on" and process ends, and it shoud be synchronized with the progress bar. Is there a way to do this .
Please let me know
Thanks,
Ankit G
Solved!
Go to Solution.

Are you referring to a LabVIEW horizontal/vertical progress bar, which basically has a U8 integer constantly written to it? Is this in a loop as it fills up?
If so, there is an entire palette that allows you to play waveforms. As you're writing to your progress bar the number, you can keep checking what that number is (event or case structure), and when it hits particular values, you play particular sounds. Here is a screenshot of that palette.
Ravi A.
National Instruments | Applications Engineer

Can anyone recommend a free file uploader with progress bar?

Can anyone recommend a free file uploader with progress bar?
I have searched google but with no luck.
Ideally it would be a DW extension but that might be wishing
for too much.
I would like a large file limit for video and multiple file
extensions allowed.
Thanks in advance

Heya,
Check out this due Waleed he has some nice tuts and here's
a
link
to file upload with progress bar tutorial he has. Granted it
looks like it's just an animated gif letting users know their file
is uploading; if you want realtime upload information displayed for
the user you're gonna have to look at something like Flash with the
power of actionscript to achieve that result.
Hope that helps!

Help - Grey wheel with progress bar on start up and then Macbook Pro turns of.

So i recently bought a Macbook Pro 13 inch (the lower end). While doing my research i found the smartest thing to have a relatively fast macbook was to increase the ram. I bought http://www.newegg.com/Product/Product.aspx?Item=N82E16820148345 and installed it in my macbook pro. After starting up the macbook, i got to my login screen. However, everytime the computer would try to start up to my account, i would get a blue screen and then be brough back to my login page for the account. I assumed that the RAM was not fitted properly since my research indicated that it was most likely the problem. I re-installed the RAM sticks with more force but to no avail. Then i even switched the RAM sticks while installing to make sure that either one of my new RAM chips was not faulty but after a while, my MBP refuses to start up. I get the grey apple logo, with a spinning wheel and progress bar. The bar goes a quarter length before the laptop shuts off. I then put it in the original RAM sticks, but the same problem. Apple logo, spinning wheel, progress bar and then powers off. Any suggestions or thoughts as to what may have happened? Thank you!

Last night the electricity went out and my power surge protector was not working so my iMac just force shut downed.
So, when the electricity came back i turned on my Mac but it is *Stuck in the Startup/Boot Screen with a Grey Apple Logo,a Empty Progress Bar with stays for 1 or 2 minutes and a small Spinning Wheel which would Spin Forver! I Have tried the SMC and Pram reset but no use, i have also tried to insert my OS X Lion 10.7 Installation disk and it would not load if i hold the C Key in the Startup, I Have Managed to go to Disk Utility Through "Recovery HD" but the Volume "Macintosh HD" is Greyed out and Unmounted and i cannot repair it. There are some files that i'd like to Recover if there is a way to fix it without deleting files.
**PLEASE HELP ME FIX THIS!**
Details about the iMac:
iMac 21.5 Inch i think from Mid 2010,
OS X Lion installed maybe 10.7.2 or 10.7.3 (im not sure)

SAP BPC 7.5 Client, Silent install but with progress bar, can it be done?

Hi All,
I need to uninstall the BPC 7 Client and then deploy 7.5 to around 250 users accross the country.
We have SCCM (SMS) in place so will be using that.
I have the uninstall of 7 sorted and I have the response file etc sorted for the silent install of 7.5 and the install runs, silently, no issue.
Is there a way though that one can "turn on" the progress bar during the install? So that users dont shutdown or disconnect in the 15min it takes the install to run.
By way of example, in the SAP Business objects enterprise client on can configure the Silent install so that although it never prompts the user for a reponse there is a progress bar that runs, indicating that there is an install in progress.
Thanks in advance,
Bryan

Hi Sebastian,
No worries, I am using a pop up countdown so the users have some idea on progress. Would love to know why the install runs for over 15min.
In the above case the uninstall was easy as we had deployed using MS AppV so it was just a case of deleting the advert in SCCM and the application was pulled from the users desktops.
For 7.5 I am using a vbscript with following to uninstall:
The install string pulled from the clients registry uninstall folder:
RunCommand Chr(34) & "C:\Program Files\InstallShield Installation Information\{EC8753EF-EE78-48B5-A4D0-FBBD237B5D53}\setup.exe" & Chr(34) & " -runfromtemp -l0x0009UNINSTALL -removeonly"
We create a custom link, so this deletes it.
DeleteFile "c:\Users\Public\Desktop\SAP BPC 7.5.lnk"
You should be able to create something similar for 7.0 & 7.1
Hope that helps,
Bryan

MacBook Pro frozen on startup screen with progress bar and then it turns off

Hello, I have a MacBook Pro 15" of early 2012 with a i5 Intel, 4GB of RAM and a 500 GB HD.
I was installing the new suit of Adobe, when suddenly my Mac got frozen, vertical coloured lines appeared and the image on screen went distorted. I had to reboot the Mac by holding the power button until the screen turned off and when I turned it on, the lines appeared again and it itself automatically rebooted. Then the screen (now with no vertical lines) got frozen on the startup grey screen with the apple logo and the spinning wheel for hours with no response.
I tried to follow the steps of the official mac forums like verifying the HD with CMD+R and then Disk Utility, it says everything's fine; the same happens with CMD+S, no errors. I reinstalled Mavericks with the same CMD+R. I already reset the PRAM, SMC and performed a Safe Boot staring up in Single user mode and Verbose Mode and nothing, the same startup screen. I made too thins thing of holding shift until the progress bar appeared. Three days later (Today) I repeated the steps again and finally the verbose mode. Now, when I turn it on, the startup screen appears again (Apple Log and spinning wheel) with a progress bar. When it completes, the Mac turn itself off.
if you can help me, please. I don't know what else to do. The last thing is technical service.

Hi again ggt15,
You can find some more information about the Recovery Partition of your hard drive here:
OS X: About OS X Recovery
http://support.apple.com/kb/HT4718
It sounds like you might be trying to reinstall your copy of the operating system. If that's the case, you may also find some helpful information here:
OS X Lion: Reinstall Mac OS X
http://support.apple.com/kb/PH3878
Thank you for using the Apple Support Community. Due to the nature of your issue or question you may find more information by using another one of Apple's support resources - https://expresslane.apple.com/GetproductgroupList.action.
Cheers,
Braden

IMac SLOWLY Starts Up With Progress Bar

Just the other day my iMac has started doing something very annoying: It starts up with a white screen and a gray progress bar, and it takes a long time to start. It does this each time I start it now. I have not added any new hardware/software. Any ideas?

That usually only happens if you had to manually force shut it down. See http://support.apple.com/kb/ht3964 for details.

Switch to install with progress bar ONLY!

I have successfully installed Photoshop CS3 onto Windows XP SP2. However, I do not want my install to be completely silent: I want to see a progress bar.
For silent install I use the following switch: setup.exe --mode=silent
The next line in cmd says"UI:Silent"
If I use no switches (only type in setup.exe), the next line in cmd is: "UI:Full" Also, "setup.exe --mode=gui" will initiate "UI:Full".
What are other install switches? I want a silent install with a progress bar only.

We too are in the same boat, we need a progress bar so that our users know that we are deploying the application.
I've tried various random switch for the "UI mode" but none work. There must be others than silent or Full.

Booting up with progress bar

I was running Spotify earlier today with a completely dim screen to save battery. The battery died and I just plugged it in and tried to wake it up. I saw the screen for a few seconds and then it went black. Trying to brighten the screen did nothing and neither did pressing the power button. So I decided to hold down the power button and restart. When I did, I got the apple logo with a spinning wheel and a progress bar under it. It's been sitting like that for over an hour with the progress bar not filling at all. What should I do? Should I let it sit like that and see if it fills eventually? Or try to reset the pram?

Try restarting your MacBook Pro in recovery mode (holding down the command + R keys while restarting) then run disk utility on your hard drive to repair it. http://support.apple.com/kb/HT1782

Won't wakeup w/o power button, then grey dimmed screen with progress bar

Hello to all,
My PB Alu works flawlessly but for one problem. I can't wake it up as I usually do by simply touching the keyboard or opening it up.
I now have to push the power button for a long time, then it kind of restarts but instead of getting the usual startup, I get the last screen I had when the computer got in sleep mode, totally dimmed and in black and white (slightly grey) with a progress bar at the bottom. When finished, the computer returns to the screen I had when I put it to sleep.
A long slow procedure and specially annoying when an external screen is connected.
What can this be?
Thanks for the help.
Mark

Hello:
I would try restoring as an approach to eliminating some software glitch. However, you might also have a hardware problem (not good news).
Barry

IPhoto 09 rebuild stuck Examining Library with progress bar unmoved

Similar Messages

Maybe you are looking for