IPM and dynamic user tracking not running properly.

Hello, I've got two problems after a reinstallation of CiscoWorks LMS 3.2.
Versions of software components:
LMS-3.2
Campus Manager-5.2.1
CiscoView-6.1.9
CiscoWorks Assistant-1.2.0
CiscoWorks Common Services-3.3.0
Device Fault Manager-3.2.0
Integration Utility-1.9.0
Internetwork Performance Monitor-4.2.0
LMS Portal-1.2.0
Resource Manager Essentials-4.3.0
First probelm I have sounds pretty much like this thread:
https://supportforums.cisco.com/message/3064784#3064784
Source device is a WS-C3560-8PC - 12.2(55)SE1 - C3560-IPSERVICESK9-M
I configured a IPM collector, if I have a look at the "Collector Management" the collector is running and I can also monitor the running collector.
But if I have a look at the running config of the switch, there is no ip sla collector configuration but I can see the ip sla statistics via the show command.
#sh ip sla configuration 135123
IP SLAs, Infrastructure Engine-II.
Entry number: 135123
Owner: ipm|XXXS1077
Tag: QA-Site1-Site2
Type of operation to perform: udp-jitter
Target address/Source address: target ip address/source ip address
Target port/Source port: 2000/0
Type Of Service parameter: 0xB8
Operation timeout (milliseconds): 5000
Codec Type: g729a
Codec Number Of Packets: 1000
Codec Packet Size: 32
Codec Interval (milliseconds): 20
Advantage Factor: 12
Verify data: No
Vrf Name:
Control Packets: enabled
Schedule:
    Operation frequency (seconds): 60
    Next Scheduled Start Time: Start Time already passed
    Group Scheduled : FALSE
    Randomly Scheduled : FALSE
    Life (seconds): Forever
    Entry Ageout (seconds): 3600
    Recurring (Starting Everyday): FALSE
    Status of entry (SNMP RowStatus): Active
Threshold (milliseconds): 5000
Distribution Statistics:
    Number of statistic hours kept: 2
    Number of statistic distribution buckets kept: 1
    Statistic distribution interval (milliseconds): 20
Enhanced History:
#sh ip sla statistics
Round Trip Time (RTT) for       Index 135123
Type of operation: jitter
        Latest RTT: 45 ms
Latest operation start time: 14:36:31.759 MET Wed Mar 16 2011
Latest operation return code: OK
RTT Values
        Number Of RTT: 1000
        RTT Min/Avg/Max: 21/45/60 ms
Latency one-way time milliseconds
        Number of Latency one-way Samples: 0
        Source to Destination Latency one way Min/Avg/Max: 0/0/0 ms
        Destination to Source Latency one way Min/Avg/Max: 0/0/0 ms
Jitter time milliseconds
        Number of SD Jitter Samples: 999
        Number of DS Jitter Samples: 999
        Source to Destination Jitter Min/Avg/Max: 0/3/15 ms
        Destination to Source Jitter Min/Avg/Max: 0/1/9 ms
Packet Loss Values
        Loss Source to Destination: 0           Loss Destination to Source: 0
        Out Of Sequence: 0      Tail Drop: 0
        Packet Late Arrival: 0 Packet Skipped: 0
Voice Score Values
        Calculated Planning Impairment Factor (ICPIF): 11
MOS score: 4.06
Number of successes: 18
Number of failures: 0
Operation time to live: Forever
#sh run all | include 135123
Any suggestions? Am I right?
The second problem is about the dynamic user tracking like these theads https://supportforums.cisco.com/message/3135881#3135881 or
https://supportforums.cisco.com/message/3195492#3195492
Access switches are configured properly, the configuration ran without any problems with the previous installation.
No changes done at the configuration, using the default trap listener port etc.
In the macuhic.log file I get entries like in the attached txt.
When I try to run a full Campus Manager Data Collection I get the following errormessage:
Failed to start acquisition: Construction of XML data required for UT is in progress.Please try after some time
Also any suggestions? Am I right, too?

By default IP SLA collectors installed by IPM do not appear in the running configuration. If you want to install the collectors into the running configuration, then set the "Copy IPSLA Configuration to running-config" property under IPM > Admin > Application Settings, then delete and recreate the collector.
Your Campus problem could be CSCtd49439 (a patch is available by contacting TAC). However, you should start a new thread for your Campus problem.

Similar Messages

SMF and multi-user service not running

Hi,
I have an issue with several services not starting ...
As you can see, the multi-user services is "offline*" And it remains like this...
I've recently patched the system hoping it would resolve this issue, but no luck. Restarting the server does not help.
# svcs | grep multi-user
offline 14:14:21 svc:/milestone/multi-user-server:default
offline* 14:14:53 svc:/milestone/multi-user:default
# svcs -xv
svc:/milestone/multi-user:default (multi-user milestone)
State: offline since Wed Dec 05 14:14:53 2007
Reason: Start method is running.
See: http://sun.com/msg/SMF-8000-C4
See: man -M /usr/share/man -s 1M init
See: /var/svc/log/milestone-multi-user:default.log
Impact: 6 dependent services are not running:
svc:/system/webconsole:console
svc:/milestone/multi-user-server:default
svc:/system/basicreg:default
svc:/system/zones:default
svc:/application/graphical-login/cde-login:default
svc:/application/cde-printinfo:default
I've tried to enable the services above manually, but had no luck.
Thanks.

Darren_Dunham wrote:
>
# svcs | grep multi-user
offline 14:14:21 svc:/milestone/multi-user-server:default
offline* 14:14:53 svc:/milestone/multi-user:default
# svcs -xv
svc:/milestone/multi-user:default (multi-user milestone)
State: offline since Wed Dec 05 14:14:53 2007
Reason: Start method is running.The start method of milestone/multi-user is responsible for (among other things), running all the /etc/rc2.d scripts. If you've placed a startup script in there and it's hanging, you'll see this behavior. From memory, I think there's a 30 minute timeout before it gives up and continues.
During the problem period, you probably want to do a 'ps -ef | grep rc' and look for any rc scripts running. That will probably point to a startup script hanging.
DarrenThanks Darren,
That was the problem. A hung script in rc2.d/
What is odd, is that this script is the same on many of our machines and no problems have been found until now. Thanks for your help. Killing that processes made everything start properly.

Accidentally removed from,sharing and permissions the admin user,and now i do not when i find the home icon at my computer i do not have permmission,and the mac does not works properly,lots of question mark at the dock ,please help

accidentally removed from,sharing and permissions the admin user,and now i do not when i find the home icon at my computer i do not have permmission,and the mac does not works properly,lots of question mark at the dock ,please help

I'm going to assume that since you deleted your hard drive and all its files, you had a backup, yes? If the backup has an OS (bootable clone), then you can boot into it by holding down the option key when you start up you iMac and choose the backup drive. Then use Carbon Copy Cloner or Super Duper to copy the files back to your iMac.

I have a copy of Web Premium CS3 which was installed on a Windows Vista PC. I have a new Windows 7 PC and the installation disc will not run properly. The installation begins and then asks for the CS3 disc to be inserted. If I re-insert the CD I just g

I have a copy of Web Premium CS3 which was installed on a Windows Vista PC. I have a new Windows 7 PC and the installation disc will not run properly. The installation begins and then asks for the CS3 disc to be inserted. If I re-insert the CD I just get a message asking for the disc to be inserted. any ideas anyone?

Use the download version:
Download CS3 products
Mylenium

[svn:bz-trunk] 13744: Bug: BLZ-481 - AMFConnection JUnit test do not run properly as part of checkintests on Mac (and Windows?)

Revision: 13744
Revision: 13744
Author:   [email protected]
Date:     2010-01-25 01:14:09 -0800 (Mon, 25 Jan 2010)
Log Message:
Bug: BLZ-481 - AMFConnection JUnit test do not run properly as part of checkintests on Mac (and Windows?)
QA: No
Doc: No
Checkintests: Pass
Details:
-Don't start the server before unit task, unit task already checks if the server is not running and starts the server.
-Don't stop the server after FlexUnit tests, JUnit tests need the server running, and they will stop the server after they are done.
Ticket Links:
    http://bugs.adobe.com/jira/browse/BLZ-481
Modified Paths:
    blazeds/trunk/build.xml
    blazeds/trunk/qa/apps/qa-regress/testsuites/flexunit/build.xml

Tony,
It appears that in the past few days you have not received a response to your
posting. That concerns us, and has triggered this automated reply.
Has your problem been resolved? If not, you might try one of the following options:
- Do a search of our knowledgebase at http://support.novell.com/search/kb_index.jsp
- Check all of the other support tools and options available at
http://support.novell.com.
- You could also try posting your message again. Make sure it is posted in the
correct newsgroup. (http://support.novell.com/forums)
Be sure to read the forum FAQ about what to expect in the way of responses:
http://support.novell.com/forums/faq_general.html
If this is a reply to a duplicate posting, please ignore and accept our apologies
and rest assured we will issue a stern reprimand to our posting bot.
Good luck!
Your Novell Product Support Forums Team
http://support.novell.com/forums/

After i have downloaded firefox 9.1 and tried to open it, i get the sentence : it couldn't be prepared properly (default 0xc0150004) and the program does not run

after i have downloaded firefox 9.1 and tried to open it, i get the sentence : it couldn't be prepared properly (default 0xc0150004) and the programm does not run

I couldn't find anything on the error text you posted but I did find lots of google hits on [http://www.google.com/search?q=%22The+application+failed+to+initialize+properly%22+0xc0150004 "The application failed to initialize properly" 0xc0150004]. Is that the error?
In any case, did you try a clean reinstall of Firefox? If not, open the C:\Program Files folder and delete the '''Mozilla Firefox''' folder, if it's there. Next, go to mozilla.org/firefox click the green download button and install a new copy.

Dynamic User Tracking

I would like to get the real time updates on end hosts on my switches. From reading other posts it sounds like I need to do the following:
1. Configure DHCP snooping on the switches.
2. Enable the mac notification traps on the switches and verify they are being sent to LMS.
I have catalyst 4000 and 4500 access switches. I've read that I may have problems with how LMS will handle the traps from the 4500 switches in this post: http://forums.cisco.com/eforum/servlet/NetProf?page=netprof&forum=Network%20Infrastructure&topic=Network%20Management&topicID=.ee71a02&fromOutline=&CommCmd=MB%3Fcmd%3Ddisplay_location%26location%3D.2cd34898
Has anyone had much luck in getting dynamic user tracking to work with the Catalyst 4500?

Not really. You'd have to run major acquisitions back to back to back, and that will just put too much strain on the server (and network).

Repaint not running properly when called in another class/actionlistener

I've got this code that is suppose to call and create a JPanel
(The frame and timeframe variables were declared statically at the beginning of the class)
When I call the runGame1 method from the main, the code runs fine and my JPanel is being repainted with the time and pictures, but when I can this runGame1 method from an ActionListener/actionPerformed method, it doesn't repaint properly and the while loop is running properly but I think there isn't enough resources for the method to actually paint my JFrame?? The JFrames open but nothing is painted.
Anyone know what I can do?
More Info........................
Basically my program contains a title JFrame and 2 game JFrames, I want to be able to call the game JFrames from the title JFrames and go back and forth from the JPanels.
The title JFrame consists of just components such as JLabels and JButtons.
One of the game JFrames consists of JLabels, JTextFields and JButtons, basically the method generates random numbers and an arithmetic operation that the user has to calculate and enter in the program and the program checks if its correct or not.
One of the game JFrames consist of a paint method that paints circles and the user has to click on it and when a circle is clicked on, it is repainted to not show the circle.(a coordinate system is used etc etc)
public static void runGame1(){
          k=20;
          kcolor=2;
          fillcolor();
          checkcolor();
          frame = new Circlepix();
          timeframe = new TimerPanel();
          time1 = System.currentTimeMillis();
          //Repaints the count down
          while((60-seconds)>0){
               try{
                    Thread.sleep(1000);
               catch(InterruptedException e){
               timeframe.repaint();
               System.out.println("aaa");
          timeframe.dispose();
public void actionPerformed(ActionEvent e) {
               if (e.getActionCommand().equals("Reset Scores"))
                    game1score=0;
                    game2score=0;
               else if(e.getActionCommand().equals("Speed Circles")){
               mainframe.dispose();
               runGame1();
          }

main is running in a different thread (the main thread)
action events are sent via the event dispatch thread, and painting is done on the event dispatch thread.
You should always be calling your runGame1 method from a separate thread of your own, so you don't block the event dispatch thread and painting
http://java.sun.com/docs/books/tutorial/uiswing/concurrency/index.html
Edited by: bsampieri on Jun 5, 2008 4:50 PM

Dynamic User Tracking Ignoring Traps

LMS3.2
Campus Manager 5.2.0
Set up a switch per instructions and moved a PC from port to port. The Results:
S0068SWT0CW#sh mac ad not change
MAC Notification Feature is Enabled on the switch
Interval between Notification Traps : 1 secs
Number of MAC Addresses Added : 5
Number of MAC Addresses Removed : 4
Number of Notifications sent to NMS : 9
Maximum Number of entries configured in History Table : 1
Current History Table Length : 1
MAC Notification Traps are Enabled
History Table contents
History Index 1, Entry Timestamp 954048629, Despatch Timestamp 954048629
MAC Changed Message :
Operation: Added   Vlan: 5     MAC Addr: 0024.e8f4.52fe Dot1dBasePort: 4
S0068SWT0CW#
Wireshark on the server shows the SNMP traps arrived at the server, but nothing is logged in the MACUHIC log (all items set for debugging and debugging is enabled) and nothing shows up in the end host report.
Trap listener configuration Listen traps from device is checked.
Dynamic User Tracking Configuration validate trap source by IP address is checked. The source address in validate trap source matches the source shown by wire shark.
What am I missing? How can I further troubleshoot this?    Thanks

Trap listener Configuration
Listen traps from device is selected
Listen traps from DFM/HPOV is not selected
trap listener port   1431
Dynamic User Tracking Configuration
validate SNMP Community     not selected
validate trap source is selected
IP address is 10.67.139.100
It didn't work with the validate trap source not selected
I am not using DFM. The device is sending its traps to the server with campus manager.

Dynamic User Tracking with WS-C4506-E

Hello,
I've the following problem, configured dynamic user tracking on a
WS-C4506-E with a WS-X45-SUP6L-E, System image file is a Version 12.2(53)SG2
Interface configuration:
snmp trap mac-notification change added
snmp trap mac-notification change removed
Global configuration:
snmp-server enable traps mac-notification change
snmp-server host xx.xxx.xx.xxx version 2c COMMUNITY udp-port 1431 mac-notification
mac address-table notification change interval 60
mac address-table notification change history-size 50
mac address-table notification change
#sh mac address-table notification change
MAC Notification Feature is Enabled on the switch
Interval between Notification Traps : 60 secs
Number of MAC Addresses Added : 21509
Number of MAC Addresses Removed : 21484
Number of Notifications sent to NMS : 11632
Maximum Number of entries configured in History Table : 50
Current History Table Length : 50
MAC Notification Traps are Enabled
UTU2 does not found any records for the device name or if I search for a directly connected PC to this switch.

Where is this Collector Status screen? What dashboard is it on ?
>> Device Center > Troubleshooting Workflow
The fact that you have success for usertracking does not mean you server receives mac address notification traps. It only means the passive usertracking has run. The UT results from the other switch may come from this process.
>> Yes you're right.
Only via snoop or packetcapture you can be sure you receive the traps you want.
>> I set up a packetcapture on the server, the server receives the mac address notification traps on UDP port 1431.
>>Dynamic user tracking of switches from the same site works...for example I have three WS-C3750V2-48PS-S over >>there.
Also if you look at the Collection Sumary in the Inventory -> Device Status dashboard you may find that some devics fail on usertracking.
>> Both switches are not under the failed devices.
>>I'm a little bit confused now.... I can't even start a acquisition manually, LMS says device is not reacheable... but in Device Center (1st picture) "ping", "snmp" etc... is OK...

Web pages are very slow to load airport is fine and other users do not have any problems

my macbook pro is very slow to load web pages airport is running fine and other users do not have any issues?

Likely a corrupted cache, do #12 and #13 here, if that doesn't work run through the Steps 1+
Step by Step to fix your Mac
Why is my computer slow?

I just finished installing 11.3 and now iTunes will not run.

I just finished installing 11.3 and now iTunes will not run. I have uninstalled itunes and resinstalled several times. Now when I attempt to start iTunes i get the following two error dialogues:“The procedure entry point ADiAdID_AcquireMatchSlotIfNecessary could not be located in the dynamic link library iAdCore.dll. and was not installed correctly. Please reinstall iTunes. Error 7 (Windows error 127)

Hi Greybeard1955,
Welcome to the Apple Support Communities! I understand that iTunes is not opening after uninstalling and re-installing it. When iTunes is uninstalled on a Windows computer, all of its components must be removed as well and they must be removed in a specific order. Below is the article for uninstalling on Windows 7. I recommend uninstalling iTunes and all components in order and reinstalling fresh.
Removing and reinstalling iTunes and other software components for Windows Vista, Windows 7, or Windows 8
http://support.apple.com/kb/ht1923
1. Remove iTunes and related components from the Control Panel
Use the Control Panel to uninstall iTunes and related software components in the following order and then restart your computer:
iTunes
Apple Software Update
Apple Mobile Device Support
Bonjour
Apple Application Support (iTunes 9 or later)
I hope this helps,
-Joe

FOR ALL ENTRIES stmnt. in SELECT query is not running properly

Hello experts,
          In my report program, I write one query on table BSIS.
         Internal table declaration -
       DATA : BEGIN OF DLC_BSIS OCCURS 0,
                        BUKRS LIKE BSIS-BUKRS,
                        GJAHR LIKE BSIS-GJAHR,
                        BELNR LIKE BSIS-BELNR,
                        SHKZG LIKE BSIS-SHKZG,
                        BSCHL LIKE BSIS-BSCHL,
                        AUFNR LIKE BSIS-AUFNR,
                        HKONT LIKE BSIS-HKONT,
                        QSSKZ LIKE BSIS-QSSKZ,
                        DMBTR LIKE BSIS-DMBTR,
                   END OF DLC_BSIS.
Query as follows --
         SELECT BUKRS
                       GJAHR
                       BELNR
                       AHKZG
                       BSCHL
                       AUFNR
                       HKONT
                       QSSKZ
                        DMBTR FROM BSIS
                                  INTO TABLE DLC_BSIS
                                 FOR ALL ENTRIES IN IT_BKPF2
                                 WHERE BELNR = IT_BKPF2-BELNR
                                              AND BUKRS = IT_BKPF2-BUKRS
                                              AND GJAHR = IT_BKPF2-GJAHR.
IT_BKPF2 internal table having -- BUKRS - LT01
                                                     BELNR - 6400000061
                                                     GJAHR - 2009.
And in BSIS database table -- 3 entries are there for the above documnet.
But, in my internal only one entry has come for the same above document.
I think For all entries stmnt. is not running properly. But Why it's not running properly.??
What would be the reason..??
Thanks in advance....!!
Regards,
Poonam.

>
Poonam Patil wrote:
> Hello experts,
>           In my report program, I write one query on table BSIS.
>
>          Internal table declaration -
>
>        DATA : BEGIN OF DLC_BSIS OCCURS 0,
>                         BUKRS LIKE BSIS-BUKRS,
>                         GJAHR LIKE BSIS-GJAHR,
>                         BELNR LIKE BSIS-BELNR,
>                         SHKZG LIKE BSIS-SHKZG,
>                         BSCHL LIKE BSIS-BSCHL,
>                         AUFNR LIKE BSIS-AUFNR,
>                         HKONT LIKE BSIS-HKONT,
>                         QSSKZ LIKE BSIS-QSSKZ,
>                         DMBTR LIKE BSIS-DMBTR,
>                    END OF DLC_BSIS.
>
>          Query as follows --
>
>          SELECT BUKRS
>                        GJAHR
>                        BELNR
>                        AHKZG
>                        BSCHL
>                        AUFNR
>                        HKONT
>                        QSSKZ
>                         DMBTR FROM BSIS
>                                   INTO TABLE DLC_BSIS
>                                  FOR ALL ENTRIES IN IT_BKPF2
>                                  WHERE BELNR = IT_BKPF2-BELNR
>                                               AND BUKRS = IT_BKPF2-BUKRS
>                                               AND GJAHR = IT_BKPF2-GJAHR.
>
> IT_BKPF2 internal table having -- BUKRS - LT01
>                                                      BELNR - 6400000061
>                                                      GJAHR - 2009.
>
> And in BSIS database table -- 3 entries are there for the above documnet.
>
> But, in my internal only one entry has come for the same above document.
>
> I think For all entries stmnt. is not running properly. But Why it's not running properly.??
> What would be the reason..??
>
>
> Thanks in advance....!!
>
> Regards,
> Poonam.
include the buzei field in selection criteria i have faced the same situation earlier.
always select all the key fields.
varun

Gimp will not run properly

I just purchased a 24 inch Imac and Gimp will not run properly. I have the latest system updates and firmware. Gimp starts X11 and appears to load, but the only item visible is the Gimp menu, none of the tools. It shows as running in the dock.
If I try to open a graphic with Gimp, it loads but the graphic is not visible and only the Gimp menu is visible in the menu bar. It shows up as running in the dock.
It works fine on a G4 quicksilver. I have the latest version 2.2.11
Thanks,
Fran
IMAG INTEL Mac OS X (10.4)

Hello Francis,
Did Gimp ever load properly? On first load, it should have gone through an installer within X11. Also, I've noticed that my image windows start up hidden. There also may be a bug in which clicking on the Gimp app icon in the dock itself won't bring the windows forward, so you have to use the X11 icon instead. Try using Expose to show all windows in all applications to see if they've opened but sort of "off-screen."
It could be a bad installation, or it could be that somehow the toolbars and palettes, etc. in Gimp just never appeared. Check to make sure X11 is up to date as well. I'm currently running 1.1.3 with XFree86 4.4.0.

Golden gate extract and replicate process are not running.

All,
I am trying replicate data between two oracle databases using golden gate.
I am trying this scenario in a single machine(two databases and golden gate are on same windows machine)
1. I have two databases PROD, UAT both are running on 11.2 oracle home.
2. Created the ggate user both the databases, and enabled supplemental logging.
3. Ran the following scripts in both databases.
SQL> @marker_setup.sql
SQL> @ddl_setup.sql
SQL> @role_setup.sql
SQL> grant GGS_GGSUSER_ROLE to ggate;
SQL> @ddl_enable.sql
4. Connected the source database (PROD) in ggsci prompt
GGSCI (home-c07402bbc5) 79> add extract ext1, tranlog, begin now
add exttrail C:\app\Bhanu\Goldengate\lt, extract ext1
edit params ext1
EXTRACT ext1
USERID ggate@PROD, PASSWORD 123456
RMTHOST home-c07402bbc5, MGRPORT 7840
rmttrail C:\app\Bhanu\Goldengate\lt
ddl include mapped objname bhanu.* // bhanu is a schema in PROD database.
TABLE bhanu.*;
5. Connected the target database(UAT) in ggsci prompt
add checkpointtable ggate.checkpoint
edit params ./GLOBALS
GGSCHEMA ggate
CHECKPOINTTABLE ggate.checkpoint
add replicat rep1, exttrail C:\app\Bhanu\Goldengate\Mt,checkpointtable ggate.checkpoint
edit params rep1
replicat rep1
ASSUMETARGETDEFS
userid ggate@UAT, password 123456
discardfile C:\app\Bhanu\Goldengate\rep1_discard.txt, append, megabytes 10
map bhanu.*, target kiran.*;
After that started the extract, replicat using
start extract ext1, start replicate rep1
Now the status.
GGSCI (home-c07402bbc5) 103> info all
Program Status Group Lag Time Since Chkpt
MANAGER RUNNING
EXTRACT STOPPED EXT1 00:00:00 00:11:43
REPLICAT STOPPED REP1 00:00:00 00:21:16
Can you please help me what is wrong in my setup and why extract and replicate process are not running.
Edited by: user12178861 on Nov 19, 2011 11:22 AM

Thanks for your quick reply.
I have done few changes but extract, replicate process not running.
couple of points I would like to share with you regarding my setup.
1. I am using single golden date instance to replicate the data between PROD and UAT databases.
2. GGSCI (home-c07402bbc5) 1> dblogin userid ggate@PROD,PASSWORD 123456
Successfully logged into database.
GGSCI (home-c07402bbc5) 2> info all
Program Status Group Lag Time Since Chkpt
MANAGER RUNNING
EXTRACT STOPPED EXT1 00:00:00 01:23:29
REPLICAT STOPPED REP1 00:00:00 01:33:02
GGSCI (home-c07402bbc5) 3> VIEW REPORT EXT1
ERROR: REPORT file EXT1 does not exist.
GGSCI (home-c07402bbc5) 4> start er *
Sending START request to MANAGER ...
EXTRACT EXT1 starting
Sending START request to MANAGER ...
REPLICAT REP1 starting
GGSCI (home-c07402bbc5) 5> VIEW REPORT EXT1
ERROR: REPORT file EXT1 does not exist.
GGSCI (home-c07402bbc5) 6> info all
Program Status Group Lag Time Since Chkpt
MANAGER RUNNING
EXTRACT STOPPED EXT1 00:00:00 01:24:10
REPLICAT STOPPED REP1 00:00:00 01:33:44
Target :
GGSCI (home-c07402bbc5) 1> dblogin ggate@UAT,PASSWORD 123456
ERROR: Unrecognized parameter (GGATE@UAT), expected USERID.
GGSCI (home-c07402bbc5) 2> dblogin userid ggate@UAT,PASSWORD 123456
Successfully logged into database.
GGSCI (home-c07402bbc5) 5> add replicat rep1, exttrail C:\app\Bhanu\Goldengate/lt,checkpointtable ggate.checkpoint
ERROR: REPLICAT REP1 already exists.
GGSCI (home-c07402bbc5) 6> delete replicat rep1
Deleted REPLICAT REP1.
GGSCI (home-c07402bbc5) 7> add replicat rep1, exttrail C:\app\Bhanu\Goldengate/lt,checkpointtable ggate.checkpoint
REPLICAT added.
GGSCI (home-c07402bbc5) 8> edit params rep1
GGSCI (home-c07402bbc5) 9> start er *
Sending START request to MANAGER ...
EXTRACT EXT1 starting
Sending START request to MANAGER ...
REPLICAT REP1 starting
GGSCI (home-c07402bbc5) 10> info all
Program Status Group Lag Time Since Chkpt
MANAGER RUNNING
EXTRACT STOPPED EXT1 00:00:00 01:29:46
REPLICAT STOPPED REP1 00:00:00 00:00:48
3. Is mandatory that I need two golden gate instances running each side ?
Thanks for spending your time on this problem.

IPM and dynamic user tracking not running properly.

Similar Messages

Maybe you are looking for