IPM in LMS 3.1
1. I configured ICMP jitter but its not working. Is there any specific ios requirement for icmp jitter. i have given ip sla responder
2. Is path jitter same as ICMP jitter.
Hello,
perhaps your problem is related to my. With IPM (LMS 3.2) I have defined an operation of type http (IP of www.google.de). I have configured rtr thresholds to be send as SNMP traps to my network management system (HP NNMi 9.0). Setting up the collection ends up in Config Failed, but looking on the device (show rtr conf and show rtr oper) the probe is running and operations are successful. But looking at rtr reaction-configuration there are no entries. The configuration contains the "snmp-server host" and "snmp-server enable traps rtr" statements, but no SNMP trap is sent to NNMi (the output of "show snmp" shows, that the counter for SNMP traps sent is the same - even when the measurement is over threshold or the timeout value). When I change the operation in IPM to not use thresholding the collection ends up in Running (and I can use Monitor to see the operation results online). After searching the web I found this thread here:
/* Style Definitions */
table.MsoNormalTable
{mso-style-name:"Normale Tabelle";
mso-tstyle-rowband-size:0;
mso-tstyle-colband-size:0;
mso-style-noshow:yes;
mso-style-priority:99;
mso-style-qformat:yes;
mso-style-parent:"";
mso-padding-alt:0cm 5.4pt 0cm 5.4pt;
mso-para-margin:0cm;
mso-para-margin-bottom:.0001pt;
mso-pagination:widow-orphan;
font-size:11.0pt;
font-family:"Calibri","sans-serif";
mso-ascii-font-family:Calibri;
mso-ascii-theme-font:minor-latin;
mso-fareast-font-family:"Times New Roman";
mso-fareast-theme-font:minor-fareast;
mso-hansi-font-family:Calibri;
mso-hansi-theme-font:minor-latin;
mso-bidi-font-family:"Times New Roman";
mso-bidi-theme-font:minor-bidi;}
https://supportforums.cisco.com/thread/173422?tstart=0&viewcondensed
Joe, could this be our problem?
Kind regards
Allessandro
Similar Messages
-
Traps from IPM in LMS 4.0
Hi, in LMS 4.0, is it possible to send traps from IPM? I remember that this was impossible from LMS 3.x.
Thanks.Yes.
Create it under the "operation" section. Monitor -> Performance Settings -> IP SLA -> operation, then apply to a collector. -
Internetwork performance Monitor (IPM) issue of CiscoWork LMS 2.5
Im implementing IPM 2.6 module on Ciscoworks. To analysis ICMP traffic from Source to Destination, I have made 1 IP Echo entery of source & target, where source is RouterA serial IP & Target is RouterB Serial IP. Now if Normal Ping happens from Router A to B. Traffic analysis & delay displays at IPM. Now I move one another entry where Source Router A & Destination Router C Serial IP. Now Problem begins. Due to some policies, Router A cant make normal Ping to C but extended ping happens for same but IPM cant capture extended ping traffic & delay. It always show Request timed out. Now Im stuck. Its very necessary to resolve. Waiting..
Dan,
IPM and LMS 3.2 are EOS/EOL. But the features are still available in the latest version of LMS, aka, Cisco prime LMS 4.2.
Cisco Prime LMS 4.x onwards the module specific approach was re-structured to feature centric menu, and hence Cisco Prime LMS 4.2 has all the required + enhanced IPM features.
You can upgrade to LMS 4.2, however, we encourage everyone to move to Cisco Prime Infrastructure, which is more future proof, as Marvin recommended.
IPM feature in Cisco Prime LMS 4.2 is known as Performance Management.
For more details check :
Navigating Cisco Prime Internetwork Performance Monitor Tasks in LMS 4.2
Performance Management
Cisco Prime LMS 4.2 and Cisco Prime Infrastructure 2.2 Functional Comparison
-Thanks
Vinod
**Encourage Contributors. RATE Them** -
Can I remove unwanted apps from LMS 3.2
is that possible to remove DFM and IPM from LMS 3.2 I have never used and LMS appears to be slow and i am thinking trimming some unwanted apps may help. thanks.
9 out of 10 times I have found marginally performing LMS servers to be suffering from under-provisioned memory. That is especially true on older Windows-based servers that didn't support server 64-bit OS along with the greater addressable memory ( > 4GB) they enable.
-
What's the replacement of CiscoWorks Internetwork Performance Monitor (IPM)?
Hi There
I am using a quite old tool - Ciscoworks IPM 2.5 with CWRW-1.3 in my teaching lab installed in 2004. IPM is good tool for network lab working with Cisco 3700 routers. Now I am trying to find latest IPM version to upgrade the lab. I find that latest IPM is version 4.2 with Ciscoworks LAN management Solution 3.2 only. But this production is also end-of-sale and end-of -support see the page -http://www.cisco.com/c/en/us/support/cloud-systems-management/ciscoworks-lan-management-solution-3-2/model.html
- End-of-Sale Date: 08-APR-2011 Details
- End-of-Support Date: 30-APR-2014 Details
Now I have no idea how to upgrade IPM? Which tool from Cisco or a third party can be replacement of IPM?
Dan Li,
Concordia UniversityDan,
IPM and LMS 3.2 are EOS/EOL. But the features are still available in the latest version of LMS, aka, Cisco prime LMS 4.2.
Cisco Prime LMS 4.x onwards the module specific approach was re-structured to feature centric menu, and hence Cisco Prime LMS 4.2 has all the required + enhanced IPM features.
You can upgrade to LMS 4.2, however, we encourage everyone to move to Cisco Prime Infrastructure, which is more future proof, as Marvin recommended.
IPM feature in Cisco Prime LMS 4.2 is known as Performance Management.
For more details check :
Navigating Cisco Prime Internetwork Performance Monitor Tasks in LMS 4.2
Performance Management
Cisco Prime LMS 4.2 and Cisco Prime Infrastructure 2.2 Functional Comparison
-Thanks
Vinod
**Encourage Contributors. RATE Them** -
LMS 3.2.1 IPM collector
HI,
I have LMS 3.2.1 installed in my server. When I am try to create a new collector the expected source device is not appearing in list of devices source device list. However the device is added under IPM devices and reflecting under destination devices while trying to create teh collector. The device was appearing earlier but I deleted the device from common services and re added it. The device is also managed by other module like, DFM and RME.
Please help me.
Regards,
SatyaThanks Afroj,
I have created the collectors in IPM. I had tried with all possible setting with device credentials in common services. Finally I found if the RW credential is left blank in common service device credential, the device does not appears as a source in IPM collector configuration. In initial condition we need to add a RW string in device and mention the same in common service device credential. Latter after creation of the collector if we remove the RW string then also it will continue to collect latency information from IP SLA and display it in graph.
Thanks for your kind support. -
LMS 2.6 with IPM 2.6 integration ACS 4.1, problem with IPM
Hi
Recently I integrated ACS 4.1 with LMS 2.6 follow this document:
http://www.cisco.com/en/US/prod/collateral/netmgtsw/ps6504/ps6528/ps2425/prod_white_paper0900aecd80613f62.html
The integration was a partial success, because after the integration I cannot run IPM client and Reports. Just I don't have the icon to run this features.
Some of you know why is happen, and if there is a solution?
In accord with the document above, I check the integration and was everything how this doc says. But IPM give me this problem.
Thank you really much.
Best Regards Antonello.Thank you a lot Joe.
I wrongly thought that System Administrator has totally access.
Thank you really much, I rate you post.
Best Regards Antonello -
Hi
On LMS 3.1 and 3.2, is there cisco IPM Web Client, or was it discontinued on LMS 3.2?
If there is, how do i get to install it- i.e. where do i donwload it?
Thanks a lotThe IPM web client is no longer required in LMS 3.0 and higher. The reason for this is that IPM no longer requires client-sided Java. IPM is now a full part of the rest of LMS, and only requires the client to support HTML, JavaScript, and Flash.
-
Facing problems in LMS 3.0.1 ( IPM not making graphs / visuals )
Yes. I think i am doing some mistake.
1. i have two switches. both are 6509.
2. i have configured snmp properly and can see them in rme and can do ssh also to them from cisco works
3. in ipm i try to pull reports i says "no data to poll "
4. i have tried configuring collector from source ip of loopback switch A and destination ip of loopback switch B. but when i try to take reports not coming,
5. Is there any document to refer to exact steps to generate reports, i think i am missing some step.
ALSO what configuration shall i do ( on switches to make this IPM generate graphs ).
i tried doing some configs on both switches as below (same on both) :
ip sla monitor 1
frequency 60
ip sla monitor schedule forever start now
and above snippet is same on both the boxes ????? what mistake have i done ? how to fix it and how to see the beautiful LATENCY graphs in IPM ????Thanks for the reply clarke...
\\herewith attached the screenshot of the error..unfortunately i left the site now...so other details I will be able to send it tomorrow only.. -
IPM 4.2 database for future analysis (LMS 3.2)
Hello,
How long can one keep IPM database for future analysis if one wants to keep statstical data for more than a year.
Is this possible? There is a chance to schedule for more that a year at the collector page. But it is may be to indicate the run-time but not the actuall collection of statistical data at the IPM database (NMSROOT/files/IPM/export/collectors?You can configure the purge intervals for Minute, Hourly, Daily, Weekly, and Monthly data under IPM > Admin > Purge Settings. By default, the monthly data is kept for an entire year. You can increase this provided you have the disk space to hold it.
-
IPM 4.1 (LMS 3.1) error in ipmpoller.log
Hello,
I have problems with generating reports for some collectors (No data available for the selected time period). For those collectors there is two type of errors in log:
[ pet vel 04 09:21:22 CET 2011 ],ERROR,[Poller-1234],com.cisco.nm.ipmng.common.datastructures.HistoricalDataCollector,collectStats,313,Bogus value from device while collecting the stats :nullcom.cisco.nm.ipmng.dal.DALBogusDataException
at com.cisco.nm.ipmng.dal.ProcessResponseUtil.ProcessObjectIfs(ProcessResponseUtil.java:235)
at com.cisco.nm.ipmng.dal.ProcessResponseUtil.processGetTableSnmp(ProcessResponseUtil.java:321)
at com.cisco.nm.ipmng.dal.SnmpDeviceAccess.gettable(SnmpDeviceAccess.java:2256)
at com.cisco.nm.ipmng.dal.DeviceAccess.gettable(DeviceAccess.java:230)
at com.cisco.nm.ipmng.common.datastructures.HistoricalDataCollector.collectStats(HistoricalDataCollector.java:255)
at com.cisco.nm.ipmng.common.datastructures.HistoricalDataCollector.pollDevice(HistoricalDataCollector.java:79)
at com.cisco.nm.ipmng.poller.server.DataPoller.pollCollector(DataPoller.java:345)
at com.cisco.nm.ipmng.poller.server.DataPoller.performPolling(DataPoller.java:291)
at com.cisco.nm.ipmng.poller.server.DataPoller.access$000(DataPoller.java:65)
at com.cisco.nm.ipmng.poller.server.DataPoller$1.run(DataPoller.java:515)
at java.lang.Thread.run(Thread.java:595)
[ pet vel 04 09:21:22 CET 2011 ],ERROR,[Poller-1234],com.cisco.nm.ipmng.poller.server.DataPoller,pollCollector,379,Unable to poll the collector CollectorID = 17Name = 1234AdminIndex = 133862Device = 29due to No entries
and second type:
[ pet vel 04 09:54:22 CET 2011 ],ERROR,[Writer-Test2],com.cisco.nm.ipmng.poller.server.DataWriter,writeDataInDB,403,Unable to write the collector due to null
Sometimes is enough to stop/start collector to get reports after some time, sometimes not...
Real time graph for that collectors works OK.
Regards,
MladenHello,
Hm,
"I don't see that you reproduced the polling issue in this log once debugging was enabled." - I'm not sure if we talking about same thing - there is the same error in log for that collector:
[ uto vel 08 09:21:22 CET 2011 ],ERROR,[Poller-1234],com.cisco.nm.ipmng.common.datastructures.HistoricalDataCollector,collectStats,313,Bogus value from device while collecting the stats :nullcom.cisco.nm.ipmng.dal.DALBogusDataException
"In order to get an idea of what the bogus value is, I need to see a DB insert that contains the bogus data." - how can I provide you that ? I have packet capture but I will like to get it to you on some secure way...
Regards,
Mladen -
Problem restoring LMS 2.6 data to LMS 4.0
Hello,
I'm trying to migrate from LMS 2.6 on a Windows 2003 server to LMS 4.0 on Windows 2008 R2.
Two things I'll note here which might help future people attempting to use the LMS 4.0 backup/restore scripts as detailed in the migration document:
1) Make sure nobody has installed cygwin on the server before you run the backup scripts. If they have, remove it and the reg keys.
2) On the target server make sure to run the restore script CMD session using runas or disable UAC on Windows 2008 or the restore scripts will fail
My next problem I can't get past. I've been running the restore since yesterday morning and it still hasn't finished. It hasn't moved from 40% complete migrating the IPM data but in the last 24 hours it has eaten up 6Gb more RAM.
C:\Users\zadmkovesa>e:\sw\CSCOpx\bin\perl.exe e:\Sw\CSCOpx\bin\restorebackup.pl
-d e:\lmsbackup\ -t e:\lmsbackup\temp
Restore started at : 2011/03/15 11:21:12
Please see 'E:\Sw\CSCOpx\log\restorebackup.log' for status.
USER ID is ..................................... : zadmkovesa
OS of the backup archive is..................... : Windows
WARNING: The temp directory e:\lmsbackup\temp\tempBackupData is not empty.
An earlier instance of restore operation might have been interrupt
ed before completion.
If you proceed with the restore operation, this directory and its
sub directories will be deleted.
Do you want to continue? (y-continue or n-quit, y/n)?y
Generation to be restored is ................... : 0
Backup taken from............................... : e:\lmsbackup\
Common Services version in the backup data is... : 3.0.6
Common Services is installed in................. : E:\Sw\CSCOpx
The temp folder for this restore program........ : e:\lmsbackup\temp\tempBa
ckupData
Applications installed on this machine ......... : [Common Services][Campus
Manager][Resource Manager Essentials][Device Fault Manager][cvw][cwlms][cwporta
l][ipm][upm]
Applications in the backup archive ............. : [Common Services][Campus
Manager][Resource Manager Essentials][Device Fault Manager][cvw][ipm]
WARNING: The list of applications installed on this CiscoWorks server does
not match the list of
applications in the backup archive. If you restore data from this
backup archive,it may
cause problems in the CiscoWorks applications.
Do you want to continue the restore operation? (y-continue or n-q
uit, y/n)?y
Applications to be restored are................. : [Common Services] [Campu
s Manager] [Resource Manager Essentials] [Device Fault Manager] [cvw] [ipm]
Available disk space in NMSROOT................. : 237023900 Kb
Required disk space in NMSROOT.................. : 38857544 Kb
(The temp and NMSROOT are on same device, therefore this required disk spac
e includes temp space)
Copying the backup files to the temporary location [e:\lmsbackup\temp\tempBack
upData]
preRestore of [Common Services] has started.
preRestore of [Common Services] has completed.
preRestore of [Campus Manager] has started.
preRestore of [Campus Manager] has completed.
preRestore of [Resource Manager Essentials] has started.
preRestore of [Resource Manager Essentials] has completed.
preRestore of [Device Fault Manager] has started.
preRestore of [Device Fault Manager] has completed.
preRestore of [cvw] has started.
preRestore of [cvw] has completed.
preRestore of [ipm] has started.
Not all data from IPM 2.6 will be migrated to LMS 4.0. For information on the d
ata that is migrated, see the "Migrating Data From LMS 2.6 or 2.6 SP1" section i
n the "Migrating Data to CiscoWorks LAN Management Solution 4.0" chapter in the
LMS4.0 Installation Guide for details. Do you want to continue[Y/N]:[Y]y
Do you want the IPM 2.6 collectors present in the backup to be DELETED from the
source routers [Y/N]:[Y]n
preRestore of [ipm] has completed.
doRestore of [Common Services] has started.
License check started.
WARNING: The license details in the server are different from the b
ackup data.
After restoring, please check the license available in the
server.
WARNING: Your current license count is lower than your earlier lice
nse count.
If you restore the data now, devices that exceed the curre
nt licence count
will be moved to Suspended state.
License check completed.
Restoring certificate.
WARNING: Cannot evaluate the hostname, hence the certificate
may be from this host or another host.
[ Certificate not overwritten ]
Restored Certificate.
Restoring Common Services database.
Restored Common Services database.
Restoring CMIC data.
Restored CMIC data.
Restoring CMC data.
Restored CMC data.
Restoring Security Settings.
INFO:
Backup Mode is ACS. In LMS we are not supporing ACS for AAA.
Setting Login Mode to CiscoWorks Local.
Restored Security Settings.
Restoring DCR data.
Restored DCR data.
Restoring Certificate key store.
Restored Certificate key store.
Restoring JAAS configuration.
Restored JAAS configuration.
JRM Job Migration started.
JRM job Migration done.
doRestore of [Common Services] has completed.
doRestore of [Campus Manager] has started.
doRestore of [Campus Manager] has completed.
doRestore of [Resource Manager Essentials] has started.
10% of RME Restore completed
30% of RME Restore completed
50% of RME Restore completed
70% of RME Restore completed
100% of RME Restore completed
doRestore of [Resource Manager Essentials] has completed.
doRestore of [Device Fault Manager] has started.
10% of DFM Restore completed
30% of DFM Restore completed
50% of DFM Restore completed
80% of DFM Restore completed
Going to modify Eight PM report
Modified Sucessfully Eight PM report
100% of DFM Restore completed
doRestore of [Device Fault Manager] has completed.
doRestore of [cvw] has started.
doRestore of [cvw] has completed.
doRestore of [ipm] has started.
10% of IPM migration completed
20% of IPM migration completed
30% of IPM migration completed
40% of IPM migration completed
>>>
The restore log is more than 8Mb in size so I won't upload it unless someone really wants to see it. Here is a snip from the end of it showing no clues I can make sense of:
INFO: Getting message
INFO: Connect the database dsn=ipmdb
INFO: Connected the Database
INFO: Command Executed
INFO: Connecting the Database ipmdb
INFO: Company=Cisco Systems;Application=NMTG;Signature=010fa55157edb8e14d818eb4fe3db41447146f1571g32125eb777a87cbf8b29a954f559d4221b792ff8
INFO: Preparing AUTH cmd
INFO: AUTH Executed
INFO: AUTH cmd finished
INFO: Stopping the Database engine ipmdb
INFO: E:\Sw\CSCOpx/objects/db/conf/ConfigureDB.LOCK released for the future operations...
INFO: File not exists.[Tue Mar 15 13:17:30 2011] Successfully registered the database with DM
[Tue Mar 15 13:17:30 2011] Successfully configured IPMDB database !..
10% of IPM migration completed
INFO: Start changing password for database 'ipm'...
Starting database engine ipmEng
INFO: New userinfo updated into database successfully.
Stopping database engine ipmEng
SQL Anywhere Command File Hiding Utility Version 10.0.1.4051
INFO: Password changed in odbc template file for database 'ipm'.
INFO: Password changed for ODBC registry 'ipm'.
INFO: Password changed for Property file E:\Sw\CSCOpx\lib\classpath\com\cisco\nm\cmf\dbservice2\DBServer.properties.
INFO: Database password successfully changed.
INFO: Process created
INFO: Started the Database engine : ipmEng Retry 0
INFO: Started the Database engine : ipmEng Retry 1
INFO: Started the Database engine : ipmEng Retry 2
INFO: Started the Database engine : ipmEng Retry 3
INFO: Started the Database engine : ipmEng Retry 4
INFO: Getting message
INFO: Connect the database DSN=ipm
INFO: Connected the Database
INFO: Command Executed
INFO: File not exists.[Tue Mar 15 13:18:08 2011] Updated IPM 2.6 DB password into IPM 5.0 DB
20% of IPM migration completed
The CiscoWorks Daemon Manager service is starting.
The CiscoWorks Daemon Manager service was started successfully.
[Tue Mar 15 13:18:12 2011] Waiting for all daemons to start completely...
[Tue Mar 15 13:20:12 2011] Successfully stated daemon manager
30% of IPM migration completed
[Tue Mar 15 13:20:12 2011] Checking if IPM Process is up and running
INFO:Daemon Manager is processing other tasks in the queue.Please try again later.
[Tue Mar 15 13:25:12 2011] Process IPMProcess is not running or never started
[Tue Mar 15 13:25:12 2011] Will check after 60 seconds
INFO:Daemon Manager is processing other tasks in the queue.Please try again later.
[Tue Mar 15 13:31:12 2011] Process IPMProcess is not running or never started
[Tue Mar 15 13:31:12 2011] Will check after 60 seconds
[Tue Mar 15 13:34:54 2011] Process IPMProcess is running normally
[Tue Mar 15 13:34:54 2011] Let's proceed further..
40% of IPM migration completed
[Tue Mar 15 13:39:54 2011] delete flag is 0
[Tue Mar 15 13:39:54 2011] Data passed to MigrMain : 2.6 5.0 E:\Sw\CSCOpx E:\Sw\CSCOpx e:\lmsbackup\temp\tempBackupData Migration e:\lmsbackup\temp\tempBackupData 0
Should I just wait? Is this something that might take days if I've got a lot of IPM data or is it broken? I don't really care about keeping IPM data so could I do something to complete the data migration for everything else? Any advice appreciated.
regards,
AaronThe restore can take a long time if you have a lot of data. The problem is the database needs to be completely unloaded and reloaded to convert from ASA 9 to ASA 10. However, if you do not care about IPM data, and you still have LMS 2.6 running, you can take a new LMS backup not using the wrapper.pl script (this will keep IPM from being backed up).
-
Due to growth of the network, I need to split a single LMS 3.2 server into two seperate machines (master-slave).
I've prepared two new (virtualized) window servers. installed a clean LMS 3.2 server1 (RME, CM) server 2 (DFM, IPM and HUM)
I've restored the previous backup on the new server1 (it says that application doesn't match but I continued restore CS, RME, CM)
I've restored the previous backup on the new server2 (same message, but I continued restore DFM, IPM and HUM)
Everything seems to work fine, except:
(my next step is to setup the master-slave, currently two standalone-servers)
server1:
compliancy management -> when I try to open a template, the following error occurs:
Problem with File /WEB-INF/screens/config/dcma/BaseLine/BaseLineViewer.jsp!!!nul
server2:
It won't let me to run the changehostname.pl perl script, old-hostname doesn't match the old-hostname
These are the only issues that I've seen for now... my question. Is this a supported procedure, if not, what's the best practice for splitting a server into multiple server i.e. a master/slave(s) setup.
thanks in advance for any help.Problem with File /WEB-INF/screens/config/dcma/BaseLine/BaseLineViewer.jsp!!!nul
In the meantime I discovered that for the baseline templates that I have restored, the "Device Type" is missing.
When I add a new one, it works fine. So I can reproduce this error.
Question, how can I restore the "Device Types" in the baseline templates, for some reason this information is lost and causes this error
(I can't edit them via the GUI, so the solution should be editing some file(s) on the file system) -
Devices not shown in CS lms 3.2
Hi,
LMS 3.2,the devices are not shown in the CS.
In CS Device management no devices are shown(0 devices).But devices are shown in DFM,RME and IPM.
Any help??
Regards,
ChannaHI wass,
Thanks for reply..
Please find the screnshot of device management of dcr and dfm.
Device are shown in the DFM.
Regds,
Channa -
Is SNMP RO and telnet good enough for IPM?
Dear friends,
I have only SNMP RO access to the router and telnet access as well from Ciscoworks LMS.
But i dont have SNMP RW access.
Is it possible that i configure ip sla monitor manually on the routers / switches and just use IPM to poll these routers and collect the SLA statistics?
Thanks a lot
GautamIPM requires read-write access. However, you could try configuring the collectors on the devices manually, then import those collectors into IPM using the "ipm importcollector" cli command. I haven't tested doing this without having SNMP RW configured, but it should work. IPM will just not be able to fully manage the collectors, but it should be able to poll them.
Maybe you are looking for
-
In this scenario of post outgoing payment process open items , i' m facing a error titled as below The difference is too large for clearing Message no. F5263 Diagnosis A non-assigned difference exists for the specified clearing amount. The difference
-
Dear Experts, Please suggest me for the following scenario. I have material master with storage types N00 and D00, In which i have assigned the Placement strategy For D00 = R10 - R10 -D00 For N00 = N00 If the case is like that, then how the system
-
Vendor Intermediary Bank account
How can we setup intermediary bank account in SAP?
-
Cannot install into new laptop
I upgraded to a new laptop and uninstalled CS 6 from the old. Now I cannot install into the new laptop.
-
I can't read Persian (Farsi) characters in emails on my 8830 World Edition Blackberry. I used to be able to do so on my previous BB (Curve). Any help will be appreciated. Thanks Ali