Ipod does not join networks

recently upgraded ipod software. Have not been able to join my home network

Does the iPod see the network?
- Try:
- Resetting the iPod. Nothing will be lost.
Reset iPod touch: Hold down the On/Off button and the Home button at the same time for at
least ten seconds, until the Apple logo appears
- Power off and then back on the router
- Reset network settings: Settings>General>Reset> Reset Network Settings.
- iPhone and iPod touch: Troubleshooting Wi-Fi networks and connections

Similar Messages

Problem with wifi roaming - printer does not join SSID

In WiFi network with 2 APs with same SSID and security setup (WPA2) working well in roaming for PCs,
samrtphone and MacBook HP printer does not join WLAN and wireless test page from the printer shows as reason that priner see more then one AccessPoint with same SSID.
Product name HP Deskjet 3070 All-in-One Printer - B611a
Model CQ191B
Serial CN192332K805MQ
Service ID 22114
Firmware version MUM1FN1117BR
Region Europe

Assuming that one of the APs runs DHCP and that the other is bridged, turn the briged AP off. Now, connect the printer to the other AP, even if you have to move the printer.
Once the printer is connected it should work fine once you turn the second AP back on.
Say thanks by clicking "Kudos" "thumbs up" in the post that helped you.
I am employed by HP

Node does not join cluster upon reboot

Hi Guys,
I have two servers [Sun Fire X4170] clustered together using Solaris cluster 3.3 for Oracle Database. They are connected to a shared storage which is Dell Equallogic [iSCSI]. Lately, I have ran into a weird kind of a problem where as both nodes come up fine and join the cluster upon reboot; however, when I reboot one of nodes then any of them does not join cluster and shows following errors:
This is happening on both the nodes [if I reboot only one node at a time]. But if I reboot both the nodes at the same time then they successfully join the cluster and everything runs fine.
Below is the output from one node which I rebooted and it did not join the cluster and puked out following errors. The other node is running fine will all the services.
In order to get out of this situation, I have to reboot both the nodes together.
# dmesg output #
Apr 23 17:37:03 srvhqon11 ixgbe: [ID 611667 kern.info] NOTICE: ixgbe2: link down
Apr 23 17:37:12 srvhqon11 iscsi: [ID 933263 kern.notice] NOTICE: iscsi connection(5) unable to connect to target SENDTARGETS_DISCOVERY
Apr 23 17:37:12 srvhqon11 iscsi: [ID 114404 kern.notice] NOTICE: iscsi discovery failure - SendTargets (010.010.017.104)
Apr 23 17:37:13 srvhqon11 iscsi: [ID 240218 kern.notice] NOTICE: iscsi session(9) iqn.2001-05.com.equallogic:0-8a0906-96cf73708-ef30000005e50a1b-sblprdbk online
Apr 23 17:37:13 srvhqon11 scsi: [ID 583861 kern.info] sd11 at scsi_vhci0: unit-address g6090a0887073cf961b0ae505000030ef: g6090a0887073cf961b0ae505000030ef
Apr 23 17:37:13 srvhqon11 genunix: [ID 936769 kern.info] sd11 is /scsi_vhci/disk@g6090a0887073cf961b0ae505000030ef
Apr 23 17:37:13 srvhqon11 scsi: [ID 243001 kern.info] /scsi_vhci (scsi_vhci0):
Apr 23 17:37:13 srvhqon11 /scsi_vhci/disk@g6090a0887073cf961b0ae505000030ef (sd11): Command failed to complete (3) on path iscsi0/[email protected]:0-8a0906-96cf73708-ef30000005e50a1b-sblprdbk0001,0
Apr 23 17:46:54 srvhqon11 svc.startd[11]: [ID 122153 daemon.warning] svc:/network/iscsi/initiator:default: Method or service exit timed out. Killing contract 41.
Apr 23 17:46:54 srvhqon11 svc.startd[11]: [ID 636263 daemon.warning] svc:/network/iscsi/initiator:default: Method "/lib/svc/method/iscsid start" failed due to signal KILL.
Apr 23 17:46:54 srvhqon11 svc.startd[11]: [ID 748625 daemon.error] network/iscsi/initiator:default failed repeatedly: transitioned to maintenance (see 'svcs -xv' for details)
Apr 24 14:50:16 srvhqon11 svc.startd[11]: [ID 694882 daemon.notice] instance svc:/system/console-login:default exited with status 1
root@srvhqon11 # svcs -xv
svc:/system/cluster/loaddid:default (Oracle Solaris Cluster loaddid)
State: offline since Tue Apr 23 17:46:54 2013
Reason: Start method is running.
See: http://sun.com/msg/SMF-8000-C4
See: /var/svc/log/system-cluster-loaddid:default.log
Impact: 49 dependent services are not running:
svc:/system/cluster/bootcluster:default
svc:/system/cluster/cl_execd:default
svc:/system/cluster/zc_cmd_log_replay:default
svc:/system/cluster/sc_zc_member:default
svc:/system/cluster/sc_rtreg_server:default
svc:/system/cluster/sc_ifconfig_server:default
svc:/system/cluster/initdid:default
svc:/system/cluster/globaldevices:default
svc:/system/cluster/gdevsync:default
svc:/milestone/multi-user:default
svc:/system/boot-config:default
svc:/system/cluster/cl-svc-enable:default
svc:/milestone/multi-user-server:default
svc:/application/autoreg:default
svc:/system/basicreg:default
svc:/system/zones:default
svc:/system/cluster/sc_zones:default
svc:/system/cluster/scprivipd:default
svc:/system/cluster/cl-svc-cluster-milestone:default
svc:/system/cluster/sc_svtag:default
svc:/system/cluster/sckeysync:default
svc:/system/cluster/rpc-fed:default
svc:/system/cluster/rgm-starter:default
svc:/application/management/common-agent-container-1:default
svc:/system/cluster/scsymon-srv:default
svc:/system/cluster/sc_syncsa_server:default
svc:/system/cluster/scslmclean:default
svc:/system/cluster/cznetd:default
svc:/system/cluster/scdpm:default
svc:/system/cluster/rpc-pmf:default
svc:/system/cluster/pnm:default
svc:/system/cluster/sc_pnm_proxy_server:default
svc:/system/cluster/cl-event:default
svc:/system/cluster/cl-eventlog:default
svc:/system/cluster/cl-ccra:default
svc:/system/cluster/ql_upgrade:default
svc:/system/cluster/mountgfs:default
svc:/system/cluster/clusterdata:default
svc:/system/cluster/ql_rgm:default
svc:/system/cluster/scqdm:default
svc:/application/stosreg:default
svc:/application/sthwreg:default
svc:/application/graphical-login/cde-login:default
svc:/application/cde-printinfo:default
svc:/system/cluster/scvxinstall:default
svc:/system/cluster/sc_failfast:default
svc:/system/cluster/clexecd:default
svc:/system/cluster/sc_pmmd:default
svc:/system/cluster/clevent_listenerd:default
svc:/application/print/server:default (LP print server)
State: disabled since Tue Apr 23 17:36:44 2013
Reason: Disabled by an administrator.
See: http://sun.com/msg/SMF-8000-05
See: man -M /usr/share/man -s 1M lpsched
Impact: 2 dependent services are not running:
svc:/application/print/rfc1179:default
svc:/application/print/ipp-listener:default
svc:/network/iscsi/initiator:default (?)
State: maintenance since Tue Apr 23 17:46:54 2013
Reason: Restarting too quickly.
See: http://sun.com/msg/SMF-8000-L5
See: /var/svc/log/network-iscsi-initiator:default.log
Impact: This service is not running.
######## Cluster Status from working node ############
root@srvhqon10 # cluster status
=== Cluster Nodes ===
--- Node Status ---
Node Name Status
srvhqon10 Online
srvhqon11 Offline
=== Cluster Transport Paths ===
Endpoint1 Endpoint2 Status
srvhqon10:igb3 srvhqon11:igb3 faulted
srvhqon10:igb2 srvhqon11:igb2 faulted
=== Cluster Quorum ===
--- Quorum Votes Summary from (latest node reconfiguration) ---
Needed Present Possible
2 2 3
--- Quorum Votes by Node (current status) ---
Node Name Present Possible Status
srvhqon10 1 1 Online
srvhqon11 0 1 Offline
--- Quorum Votes by Device (current status) ---
Device Name Present Possible Status
d2 1 1 Online
=== Cluster Device Groups ===
--- Device Group Status ---
Device Group Name Primary Secondary Status
--- Spare, Inactive, and In Transition Nodes ---
Device Group Name Spare Nodes Inactive Nodes In Transistion Nodes
--- Multi-owner Device Group Status ---
Device Group Name Node Name Status
=== Cluster Resource Groups ===
Group Name Node Name Suspended State
ora-rg srvhqon10 No Online
srvhqon11 No Offline
nfs-rg srvhqon10 No Online
srvhqon11 No Offline
backup-rg srvhqon10 No Online
srvhqon11 No Offline
=== Cluster Resources ===
Resource Name Node Name State Status Message
ora-listener srvhqon10 Online Online
srvhqon11 Offline Offline
ora-server srvhqon10 Online Online
srvhqon11 Offline Offline
ora-stor srvhqon10 Online Online
srvhqon11 Offline Offline
ora-lh srvhqon10 Online Online - LogicalHostname online.
srvhqon11 Offline Offline
nfs-rs srvhqon10 Online Online - Service is online.
srvhqon11 Offline Offline
nfs-stor-rs srvhqon10 Online Online
srvhqon11 Offline Offline
nfs-lh-rs srvhqon10 Online Online - LogicalHostname online.
srvhqon11 Offline Offline
backup-stor srvhqon10 Online Online
srvhqon11 Offline Offline
cluster: (C383355) No response from daemon on node "srvhqon11".
=== Cluster DID Devices ===
Device Instance Node Status
/dev/did/rdsk/d1 srvhqon10 Ok
/dev/did/rdsk/d2 srvhqon10 Ok
srvhqon11 Unknown
/dev/did/rdsk/d3 srvhqon10 Ok
srvhqon11 Unknown
/dev/did/rdsk/d4 srvhqon10 Ok
/dev/did/rdsk/d5 srvhqon10 Fail
srvhqon11 Unknown
/dev/did/rdsk/d6 srvhqon11 Unknown
/dev/did/rdsk/d7 srvhqon11 Unknown
/dev/did/rdsk/d8 srvhqon10 Ok
srvhqon11 Unknown
/dev/did/rdsk/d9 srvhqon10 Ok
srvhqon11 Unknown
=== Zone Clusters ===
--- Zone Cluster Status ---
Name Node Name Zone HostName Status Zone Status
Regards.

check if your global devices are mounted properly
#cat /etc/mnttab | grep -i global
check if proper entries are there on both systems
#cat /etc/vfstab | grep -i global
give output for quoram devices .
#scstat -q
or
#clquorum list -v
also check why your scsi initiator service is going offline unexpectedly
#vi /var/svc/log/network-iscsi-initiator:default.log

Does not join to any fact source issue in 10g

HI,
I am getting below issue while compiling rpd.
Logical Dimension Table Dim-XX has a source xx_aa that does not join to any fact source.
Let me describe situation here.
In physical layer , i have one xx_v table . there is no join condition physical layer. But in BMM layer we have created two logical tables for single xx_v table and providing join in bmm layer. When am compiling it i'm getting an error.
The one which i have using current rpd, same rpd in production with out any warnings(Logical Dimension Table Dim-XX has a source xx_aa that does not join to any fact source) and they don't have any logical level mapping in content tab. But i am using same rpd in dev instance getting warnings.
Thanks,
Mal
Edited by: user10675696 on Feb 11, 2013 3:08 AM

Hi Srini,
Please find the below warning here and we don't have an hierarchy for MTL_SYSTE_ITEMS_B
[39008] Logical dimension table Mtl System Items B has a source MTL_SYSTEM_ITEMS_B that does not join to any fact source.
I am getting this in Dev instance only but not in Production. But one rpd can be used in dev and production instances.
Thanks,
Mall

IPod does not respond at all when plugged in

Alright, this topic is for people who have had this exact problem only. I don't want to get this confused with other problems and have people trying to help troubleshoot multiple problems and get things mixed up. Here's the problem.
After updating to v1.1.2 of the iPod software, the iPod does not respond when plugged in. The iPod still works fine when not plugged in. It plays music and both the standard and shuffle play modes work accordingly. The problem is when you plug the iPod in, it doesn't charge and it doesn't mount. The orange blinking light does not come on. While plugged in, it works the same way as it does when you're listening to music with it. It's as if the iPod's USB connector is dead. Here is my original post and description of the problem.
Alright, so here's my story. I bought my 512MB Shuffle in April. It has worked perfectly fine since I got it. Last night, I updated to v1.1.2 of the iPod software, clicked no when it asked if I wanted to restart, added some songs to the iPod, then restarted. As of this morning, I went to listen to some music while out for a bike ride, and I was greeted with the red battery light. I thought it was a bit odd since I had left it plugged in overnight. I figured, what the heck, I'll just plug it in and let it charge when I get back. When I got back, I plugged it into my PC and left for a while. I came back later and went to grab my Shuffle and I noticed it was cold, which was unusual after charging for a couple hours. I plugged it back in, a bit frustrated, and it never came up in Windows. I looked at the iPod plugged into the back of my PC (a high powered USB port) and sure enough, no orange light. No lights at all. I can still slide the switch to one of the play modes (standard play or shuffle) and play music for a couple seconds before it stops and says the battery's dead again. It works.. I mean it turns on and plays music, it's just not charging or mounting when I plug it in. I tried multiple computers and USB ports, none of which worked. I would really like some help with this considering it IS my only source of portable music and I'm not going to go pay $50 to talk to tech support or have it sent in for repairs. That's half of what it's worth.
I've tried uninstalling all iTunes/iPod related software from the PC I normally use it on and reinstalling it. That didn't work. I also tried uninstalling again and installing the last known working version of the iPod software, still no results. The only thing I havn't tried is giving it a good beating... Not that I would. Anyways, I hope there's a solution to this that doesn't involve buying a new one.
Here's a rundown of the computers I tested it with.
500MHZ G4 Cube (384MB RAM/Mac OSX Tiger)
400MHZ G3 iMac (384MB RAM/Mac OSX Tiger)
4.2GHZ AMD 64-Bit running Windows XP Service Pack 2 (my PC)
515MHZ Dell running Windows 2000 (256MB RAM)
UPDATE: The BIOS won't recognize the iPod, so it has nothing to do with my computer. Somehow, installing v1.1.2 of the iPod software made it so the iPod itself has USB problems. The iPod works to the extent of playing music and showing the battery charge level. I get no response at all when I plug it in, from the computer or the iPod.
I'm going to have to agree with Philip Harhay on this one. The original 10GB iPod I bought 3 years ago came with a full one-year warranty, no extra charges. I am disappointed to see the Shuffle only coming with a three-month warranty.
------------------------------------------------------------------

Help! I just purchase an iPod Shuffle for my son's birthday and I cannot get the darn thing to show up on my iMac G5. I am running OS 10.4.2 and I have downloaded the latest iPod and iTunes software. When I try to restore my iPod to the factory settings it tells me to plug the iPod into the computer, but it is plugged in. I have tried different USB ports, too. I'm running out of ideas and so is the trouble shooting Apple site. I was hoping someone out there might have some ideas.
It showed up at first and I transferred a few songs from the iTunes to the iPod but I couldn't get them to play, so I plugged it back into the USB and the icon never came up.

Ipod does not work with new usb

i got my computer cleaned and a usb 2.0 pci card put in and now my ipod does not work with it, can anyone help

tell me what you mean and i will tell. i ask the guy in the shop to remove any viruses and put my files in order and also put winzip on, ad-ware se peronal and windows defender. and to install a usb2.0 pci card, so that i can put music onto my ipod faster. is this enough for you

My ipod touch has a permanent image of the end of a USB cable with an arrow pointing to an icon of ITunes. I can't reset, and ipod does not appear on itunes when I plug it into the computer. This happened after I agreed to a failed software update.

My ipod touch has a permanent image of the end of a USB cable with an arrow pointing to an icon of ITunes. I can't reset using the two button method, and ipod does not appear on itunes when I plug it into the computer - and nothing else happens either. This happened after I agreed to a software update which failed. How can I get it going again?

Try:
- iOS: Not responding or does not turn on
- Also try DFU mode after try recovery mode
How to put iPod touch / iPhone into DFU mode « Karthik's scribblings
- If not successful and you can't fully turn the iOS device fully off, let the battery fully drain. After charging for an least an hour try the above again.
- If still not successful that usually indicates a hardware problem and an appointment at the Genius Bar of an Apple store is in order.
Apple Retail Store - Genius Bar

My iPod touch is frozen and asking me to connect to iTunes and when I do connect to iTunes the iPod does not show up. What can I do?

My iPod touch is frozen and asking me to connect to iTunes and when I do connect to iTunes the iPod does not show up. What can I do?

Try placing in DFU mode and then restoring.
How to put iPod touch / iPhone into DFU mode « Karthik's scribblings
Last, try restoring on another computer.

AIR-CAP3502I-E-K9 does not join preferred controller

I have an AIR-CAP3502I-E-K9 AP that is configured for two WLAN controllers with preferred order. However the AP does not join the primary controller, but uses the secondary one instead. I have a bunch of these AIR-CAP3502I-E-K9s , majority work fine, but three of them not.
I have tried commands according to
https://supportforums.cisco.com/docs/DOC-24917
In the controller's GUI the order is properly configured. I also tried to use 'Clear All Config" option on the controller and configured the AP from the scratch, but this did not help.
Here is what I have
XXXX#sh capwap client config
configMagicMark         0xF1E2D3C4
chkSumV2                30883
chkSumV1                1073
swVer                   7.2.111.3
adminState              ADMIN_ENABLED(1)
name                    XXXX
location                YYYY
group name
mwarName                ZZZZ1
mwarIPAddress           192.168.1.1
mwarName                ZZZZ2
mwarIPAddress           192.168.1.2
mwarName
mwarIPAddress           0.0.0.0
ssh status              Enabled
Telnet status           Enabled
numOfSlots              2
spamRebootOnAssert      1
spamStatTimer           180
randSeed                0xBAC2
transport               SPAM_TRANSPORT_L3(2)
transportCfg            SPAM_TRANSPORT_DEFAULT(0)
initialisation          SPAM_PRODUCTION_DISCOVERY(1)
ApMode                  Local
ApSubMode               Not Configured
AP Rogue Detection Mode Enabled
OfficeExtend AP         [0] Disabled
OfficeExtend AP JoinMode[0] Standard
Discovery Timer         10 secs
Heart Beat Timer        30 secs
Led State Enabled       1
Primed Interval         0
AP ILP Pre-Standard Switch Support Disabled
AP Power Injector Disabled
Infrastructure MFP validation Disabled
Configured Switch 1 Addr 192.168.1.2
Configured Switch 2 Addr 192.168.1.1
non-occupancy channels:
Ethernet (Duplex/Speed) auto/auto
*Mar 1 00:14:23.001: %CAPWAP-3-ERRORLOG: Selected MWAR 'ZZZZ2'(index 1).
*Mar 1 00:14:23.001: %CAPWAP-3-ERRORLOG: Go join a capwap controller
*Aug 22 12:21:57.000: %CAPWAP-5-DTLSREQSEND: DTLS connection request sent peer_ip: 192.168.1.2 peer_port: 5246
*Aug 22 12:21:57.581: %CAPWAP-5-DTLSREQSUCC: DTLS connection created sucessfully peer_ip: 192.168.1.2 peer_port: 5246
*Aug 22 12:21:57.581: %CAPWAP-5-SENDJOIN: sending Join Request to 192.168.1.2
My primary one is 192.168.1.1 and secondary is 192.168.1.2, but the AP joins always the secondary one.
The lines above
Configured Switch 1 Addr 192.168.1.2
Configured Switch 2 Addr 192.168.1.1
seem to be suspicious, I would expect the reverse order, but do not know how the code did it.
The only guess is that in the very beginning the AP joined 192.168.1.2, and this was the controller I configured the AP initially from. The AP seems to maybe somehow remember this.
OS version is
swVer                   7.2.111.3
Thanks,
Vlad

Yes, this is what I am trying all the time - configure the AP to point to the WLCs I want it to join.
Firstly I did through GUI, did not work.
Secondly I used 'Clear All Config" option on the controller and configured the AP from the scratch through GUI, did not work.
Thirdly I tried through command line on the AP, did not work.
I used these commands
XXXX#capwap ap primary-base ZZZZ1 192.168.1.1
XXXX#capwap ap secondary-base ZZZZ2 192.168.1.2
XXXX#sh capwap client config
configMagicMark         0xF1E2D3C4
chkSumV2                30883
chkSumV1                1072
swVer                   7.2.111.3
adminState              ADMIN_ENABLED(1)
name                    XXXX
location                YYYY
group name
mwarName                ZZZZ1
mwarIPAddress           192.168.1.1
mwarName                ZZZZ2
mwarIPAddress           192.168.1.2
mwarName
mwarIPAddress           0.0.0.0
ssh status              Enabled
Telnet status           Enabled
numOfSlots              2
spamRebootOnAssert      1
spamStatTimer           180
randSeed                0xBAC2
transport               SPAM_TRANSPORT_L3(2)
transportCfg            SPAM_TRANSPORT_DEFAULT(0)
initialisation          SPAM_PRODUCTION_DISCOVERY(1)
ApMode                  Local
ApSubMode               Not Configured
AP Rogue Detection Mode Enabled
OfficeExtend AP         [0] Disabled
OfficeExtend AP JoinMode[0] Standard
Discovery Timer         10 secs
Heart Beat Timer        30 secs
Led State Enabled       1
Primed Interval         0
AP ILP Pre-Standard Switch Support Disabled
AP Power Injector Disabled
Infrastructure MFP validation Disabled
Configured Switch 1 Addr 192.168.1.2
Configured Switch 2 Addr 192.168.1.1
non-occupancy channels:
Ethernet (Duplex/Speed) auto/auto
XXXX#sh log
Syslog logging: enabled (1 messages dropped, 8 messages rate-limited,
                0 flushes, 0 overruns, xml disabled, filtering disabled)
    Console logging: level debugging, 61 messages logged, xml disabled,
                     filtering disabled
    Monitor logging: level debugging, 0 messages logged, xml disabled,
                     filtering disabled
    Buffer logging: level debugging, 67 messages logged, xml disabled,
                    filtering disabled
    Logging Exception size (4096 bytes)
    Count and timestamp logging messages: disabled
    Trap logging: level emergencies, 0 message lines logged
        Logging to 255.255.255.255(global) (udp port 514, audit disabled, link down), 0 message lines logged, xml disabled,
               filtering disabled
Log Buffer (1048576 bytes):
*Mar 1 00:00:09.424: %SOAP_FIPS-2-SELF_TEST_IOS_SUCCESS: IOS crypto FIPS self test passed
*Mar 1 00:00:09.434: *** CRASH_LOG = YES
*Mar 1 00:00:09.434: 64bit PCIE devicesSecurity Core found.
Base Ethernet MAC address: E0:5F:B9:A8:00:7F
*Mar 1 00:00:12.482: %LINK-3-UPDOWN: Interface GigabitEthernet0, changed state to up
*Mar 1 00:00:13.731: %SOAP_FIPS-2-SELF_TEST_RAD_SUCCESS: RADIO crypto FIPS self test passed on interface Dot11Radio 0
*Mar 1 00:00:13.797: %LINEPROTO-5-UPDOWN: Line protocol on Interface GigabitEthernet0, changed state to up
*Mar 1 00:00:16.996: %SOAP_FIPS-2-SELF_TEST_RAD_SUCCESS: RADIO crypto FIPS self test passed on interface Dot11Radio 1
*Mar 1 00:00:17.052: %LWAPP-3-CLIENTEVENTLOG: Read and initialized AP event log (contains, 1024 messages)
*Mar 1 00:00:17.068: status of voice_diag_test from WLC is false
*Mar 1 00:00:19.182: %SYS-5-RESTART: System restarted --
Cisco IOS Software, C3500 Software (AP3G1-K9W8-M), Version 12.4(25e)JA2, RELEASE SOFTWARE (fc1)
Technical Support: http://www.cisco.com/techsupport
Copyright (c) 1986-2012 by Cisco Systems, Inc.
Compiled Fri 14-Sep-12 19:13 by prod_rel_team
*Mar 1 00:00:19.182: %SNMP-5-COLDSTART: SNMP agent on host XXXX is undergoing a cold start
*Mar 1 00:13:33.342: %LINK-5-CHANGED: Interface Dot11Radio1, changed state to reset
*Mar 1 00:13:33.342: %LINK-5-CHANGED: Interface Dot11Radio0, changed state to reset
*Mar 1 00:13:33.493: status of voice_diag_test from WLC is false
*Mar 1 00:13:33.632: %SSH-5-ENABLED: SSH 2.0 has been enabledlwapp_crypto_init: MIC Present and Parsed Successfully
*Mar 1 00:13:33.956: %LINEPROTO-5-UPDOWN: Line protocol on Interface GigabitEthernet0, changed state to up
*Mar 1 00:13:34.343: %LINEPROTO-5-UPDOWN: Line protocol on Interface Dot11Radio1, changed state to down
*Mar 1 00:13:34.343: %LINEPROTO-5-UPDOWN: Line protocol on Interface Dot11Radio0, changed state to down
*Mar 1 00:13:36.029: %LINEPROTO-5-UPDOWN: Line protocol on Interface BVI1, changed state to up
*Mar 1 00:13:41.484: %DHCP-6-ADDRESS_ASSIGN: Interface BVI1 assigned DHCP address 192.168.1.21, mask 255.255.255.0, hostname XXXX
*Mar 1 00:13:51.981: Logging LWAPP message to 255.255.255.255.
*Mar 1 00:14:01.997: %CAPWAP-3-ERRORLOG: Did not get log server settings from DHCP.
*Mar 1 00:14:06.099: %CDP_PD-4-POWER_OK: Full power - NEGOTIATED inline power source
*Mar 1 00:14:07.190: %LINK-3-UPDOWN: Interface Dot11Radio1, changed state to up
*Mar 1 00:14:08.191: %LINEPROTO-5-UPDOWN: Line protocol on Interface Dot11Radio1, changed state to up
*Mar 1 00:14:08.288: %LINK-3-UPDOWN: Interface Dot11Radio0, changed state to up
*Mar 1 00:14:09.289: %LINEPROTO-5-UPDOWN: Line protocol on Interface Dot11Radio0, changed state to up
*Mar 1 00:14:11.000: %CAPWAP-3-ERRORLOG: Could Not resolve CISCO-CAPWAP-CONTROLLER
*Mar 1 00:14:23.001: %CAPWAP-3-ERRORLOG: Selected MWAR 'ZZZZ2'(index 1).
*Mar 1 00:14:23.001: %CAPWAP-3-ERRORLOG: Go join a capwap controller
*Aug 23 06:07:13.000: %CAPWAP-5-DTLSREQSEND: DTLS connection request sent peer_ip: 192.168.1.2 peer_port: 5246
*Aug 23 06:07:13.578: %CAPWAP-5-DTLSREQSUCC: DTLS connection created sucessfully peer_ip: 192.168.1.2 peer_port: 5246
*Aug 23 06:07:13.578: %CAPWAP-5-SENDJOIN: sending Join Request to 192.168.1.2
*Aug 23 06:07:14.025: %LINK-3-UPDOWN: Interface Dot11Radio0, changed state to down
*Aug 23 06:07:14.091: %LINK-5-CHANGED: Interface Dot11Radio0, changed state to reset
*Aug 23 06:07:14.094: %CAPWAP-5-JOINEDCONTROLLER: AP has joined controller ZZZZ2
*Aug 23 06:07:14.154: %LINK-3-UPDOWN: Interface Dot11Radio0, changed state to up
What I think might be the key to the problem is this
Configured Switch 1 Addr 192.168.1.2
Configured Switch 2 Addr 192.168.1.1
This is not changing no matter what I do.
Thanks,
Vlad

ILife 06 update now iPod does not sync

Folks,
agter upgrading to iLife 06 the update of my iPod does not work. I get the message that iTunes cannot write or read to this disk.
I had iTunes 6.02 before the update and everything worked fine.
IPod is an 60GB photo with newesr firmware.
Thanks
Oliver

You may have an Ownership & Permissions problem on your iPod.
Select your iPod on the desktop and Get Info (command-I).
Set the permissions to 'You can Read & Write'. Expand 'Details:' and click 'Apply to enclosed items...'.
Tick the checkbox 'Ignore ownership on this volume'.
If your iPod does not show up on the desktop, you have to 'Enable disk use' in Prefernces>iPod (iTunes preferences)
Hope this helps.
M

Itunes freezes when connecting and ipod does not show up

When I connect my nano 3rd gen in windows vista using itunes 9 my ipod does not show up and itunes freezes. the ipod remains with the connected screen and I cannot close out of itunes. Any help would be wonderful... Thanks!!

I have (finally)solved the problem with my iTunes freezing! Here's what I did:
1.I backed up my entire music library to an external hard drive.
2.Then I completely uninstalled iTunes 9 from my computer.
3.After a re-boot I then completely deleted my entire music library. (this can be a little scary so I double checked my music library back up on the external drive)
4.I Googled iTunes 8 and found it at
http://www.mydigitallife.info/2009/06/28/apple-itunes-8-2-and-quicktime-7-6-2-di rect-download-links/
5. I downloaded it but before I installed it I copied my music library back to my computer. I did not copy everything that was in my original iTunes music folder however, I only copied the music,album art work, applications,games,Tv shoes, and podcasts folders. I placed those folders in a new folder called iTunes on my computer. I did not include any of the iTunes database files eg: .itl / .xml / or .itdb files as these were created in iTunes 9.
6. Now I opened iTunes 8.2 and added all of my music and other media content.
7. Next I attached my iPod nano to my computer. Then Windows automaticly open a window asking me if I wanted to scan for problems or continue without scanning. I had windows scan for problems and once that was done my iPod nano began to sync. Oh what joy!
I think, and this is only a guess based on what I've read here on Apple's discussion pages and my own experience, that there is a problem/conflict or bug with iTunes 9, Windows Vista and the 3rd -4th generation iPod. I will NOT be upgrading to iTunes 9 until Apple has addressed this issue. It seems to me that there are a lot of people having similar issues.

Help - iPod does not show up in iTunes or as disk in Windows Explorer

Would someone PLEASE tell me how to get my iPod to show up in iTunes or as disk in Windows Explorer?
According to our PC XP computers, we do not have an ipod and it won't charge when plugged into USB. It worked fine for 10 months until this morning (10/26/06). We have ruled out bad USB drive by using flash drive on that USB and it worked fine. Reseting ipod does not work (ipod does not respond to reset command hold toggle then hold menu + play for up to 10 sec). Reseting ipod within ipod menu does nothing. ANY suggestions would be GREATLY appreciated!
Thanks.

I have the same problem with my brand new 2 GB. I have reloaded software, gone through the "5 R's", tried the ipod on my PC and on my laptop -- neither computer recognizes or charges the ipod. Any info greatly appreciated.

Ipod does not appear in itunes after windows scan and fix

Two days ago, I restored my Ipod classic using Itunes 9.2.0.61. After restoration my Ipod started freezing Itunes and Vista. At a point, I saw a blue screen and my computer forced a shutdown. When it rebooted, Vista kept asking to automatically "scan and fix" problems on my Ipod. Thinking that would solve the "freeze" problem, I stupidly went ahead to have Vista scan and fix my Ipod. Now the freeze problem is gone, but my Ipod does not appear in Itunes. I have tried the five Rs from Apple, but that has not helped. Anyone with a solution?

1. Update iTunes to the latest version. Plug in your iPod. If iTunes still can't recognize it, then in iTunes in the top left corner click help> run diagnostics. On the box that comes up, check the last two things. Click next and it should identify your iPod.
2. Click on your windows start menu. Type in "services". Click on it and when it pops up, on the bottom of it click on "standard". Now Scroll down to find "Apple Mobile Device" Right click it when you see it and click on "Start". When it has started, close iTunes and replug in your iPod and it should show up.
3. Check the USB cable
4. Verify that Apple Mobile Device Support is installed
5. Restart the Apple Mobile Device Service and verify that the Apple Mobile Device USB Driver is installed.
6. If you just want to add some photos, songs and movies from computer to your devices, you can use an iTunes alternative to do the job.
7. Check for third-party software conflicts.

5th gen ipod does not connect to mac desktop or itunes

My ipod does not connect with my desktop or itunes (ie when I plug the ipod in using the original USB cable nothing happens--no charging no recognition that it has been connected). My nano does work with the same cable so I know it's not that. I've followed the support instructions resetting, downloading the latest software and restarting. I cannot, however, restore since the first step of the instruction is to connect the ipod and wait for it to show in the source list in itunes. It is also interesting that when I use the car charger the ipod does charge and shows the charging icon.
Any suggestions?

I guess i can lend my voice to the conversation. my ipod "locks up" when i connect to my computer also. i just updated itunes and have not been able to connect. there is no ipod folder on my computer when i search through ""finder". i have to "reset" it after i disconnect to continue to play it. i have done everything short of "restoring" due to i have over 3000 songs and i'm unable to back up. the manuel refers to a disk to update. i can only play songs, and recharge. need help to.

My ipod does not apprear in itunes with windows 7

my ipod does not apprear in itunes with windows 7 any ideas

1. Update iTunes to the latest version. Plug in your iPod. If iTunes still can't recognize it, then in iTunes in the top left corner click help> run diagnostics. On the box that comes up, check the last two things. Click next and it should identify your iPod.
2. Click on your windows start menu. Type in "services". Click on it and when it pops up, on the bottom of it click on "standard". Now Scroll down to find "Apple Mobile Device" Right click it when you see it and click on "Start". When it has started, close iTunes and replug in your iPod and it should show up.
3. Check the USB cable
4. Verify that Apple Mobile Device Support is installed
5. Restart the Apple Mobile Device Service and verify that the Apple Mobile Device USB Driver is installed.
6. If you just want to add some photos, songs and movies from computer to your devices, you can use an iTunes alternative to do the job.
7. Check for third-party software conflicts.

Ipod does not join networks

Similar Messages

Maybe you are looking for