Ipod does not pause when headphones are removed

My Ipod touch 3g does not pause when playing music when my headphones are pulled out or removed. Can someone help with this problem? Thanks in advance

if a restore hasn't fixed it then it's probably a hardware problem. is it still under guarantee? you probably need to take it to apple.

Similar Messages

IPod NOT pausing when headphones are removed

This feature has been entirely sporadic on my iPod. Sometimes when I remove the headphones, it pauses. Sometimes it doesn't. The software is the latest version, the iPod's in great condition, something just seems to be malfunctioning. I probably wouldn't complain about this, but I use it in my car with a tape deck adapter and in order to turn it off so it doesn't die, I just pull out the headphone jack, expecting it to pause. And then, of course, it doesnt....which *****....
Anyway, any ideas?

if a restore hasn't fixed it then it's probably a hardware problem. is it still under guarantee? you probably need to take it to apple.

Failure to pause when headphones are removed

whne i fist got my iPod phot one of the first things I noticed was that when you took the headphones out of the jack the iPod would stop playing. However i have noticed that this feature has been getting inconsitent and will replug only to hear music still playing somewher e int heh middle of a song. Why???????????

if a restore hasn't fixed it then it's probably a hardware problem. is it still under guarantee? you probably need to take it to apple.

IPod won't pause when external power removed

I use my IPod Nano to listen to audio books in my car and I have a 12 VDC charger connected to it. The 12 VDC is turned off when the car is shutoff. Older generation IPod would pause when the external power was shutoff but the new IPod doesn't. Any body know for a solution to this? I keep losing my place in the audio book which is a huge pain. Thanks.

I found a page at http://www.allpinouts.org/index.php/Apple_iPod,_iPad_and_iPhone_dock and it has a section that states:
1MOhm - Belkin auto adaptor, iPod shuts down automatically when power disconnected Connecting pin 21 to ground with a 1MOhm resistor does stop the ipod when power (i.e. Firewire-12V) is cut. Looks to be that when this pin is grounded it closes a switch so that on loss of power the Ipod shuts off. Dock has the same Resistor.
This connects to pin 21. So it appears that there may be Belkin Auto Adapters available for the new 30 pin dock connector that will allow to pause the IPod when Power is removed.

Crystal Report 2011 does not display when keyfigures are zero

I am using Crystal report 2011 with BEX Queries as Data Source. I am not able to see some of the characteristics values when keyfigures are zero or null. In BEX query there is a costCenter Characterstic, few costcenter characteristics values are zero for some months but BEX Query is designed to show as spaces even if the keyfigures are zero for those costcenters. When I am using the same Bex Query with Crystal report 2011 all the costcenters with keyfigures as zero are not showing up on the report. Can anybody suggest how I can show the characterstics values even if all the keyfigures are zero. (I have not selected any kind of suppression in section expert in crystal report), (In Bex Query CostCenter- Properties-Advanced----Access Type for Result values are set to Master Data)

Hi,
Have you made sure the correct Transport files have been loaded on the SAP system? Since you're using CR 2011, you need to make sure the Transports that come with this version of CR are present on the SAP system.
Could you see if the workaround mentioned in SAP Note: 1391673 works for you?
Here's a snippet of the SAP Note:
SAP Development team of BW BEX MDX Interface suggest the following implementation:
Since Crystal Reports is not correctly interpreting the character used to represent NULL values (by default the value: X) please use the Customizing transaction: RSCUSTV4 to change the sent value.
Please note, this is a Global setting, and will also modify the behaviour in BEx application.
WORKAROUND: Create a formula field based on the selection that always returns a number - converting null to 0.
Create a formula in BEx for the KF.
Edit the Selection
Edit the formula to behave like:
COUNT ('KF') * 'KF' + 0
('RKF' + 0) * 1
Not generally acceptable since it requires duplicating fields.
Also, business may not accept 0,00 for a NULL result.
Hope this helps!
-Abhilash

Itouch does not recognize the headphones are plugged in

Itouch (3rd gen) doesn't recognize that the headphones are plugged in and continues to play through the external speaker. I can also hear music through the headphones, they have been tested on my laptop and they work fine. Any idea what the problem might be?

Try the standard fixes to rule out a software problem:
- Reset.
- Restore from backup
- Restore to factory defaults.
If you still have the problem then yuo likely have a hardware problem, the headphone jack does go bad sometimes.

No sound when headphones are removed

I have a problem I seem to be unable to solve by myself. When I have headhones (or other external speakers) plugged in to my computer, the sound works great. When i remove them, the sound dissapears (the internal speakers don't seem to work). The sound isn't turned off (the volume is at max), but the soundcontrol is shaded and it is not possible to change it. At the same time, there's a red light in the speaker/headphone socket. What have I done, and what should I do?
/L

Hello. I have EXACTLY the same problem you have.
I was very sad because I bought my macbook 1 month ago, I mean, it´s new!.
I started searching on the www and I found on several discussions forums for mac owners that many people have the same problem. It seems that apple audio jacks are not as good as we expected them to be.
When you use external speakers or headphones, sometimes the sensor inside the audio jack gets kind of "stocked".
Many people on this forums wrote that they inserted another headphones or speakers or even a hair pin to release the sensor and it worked.
So I recommend you to try it (I will too)...but carefully. ok?
Good luck

Internal speakers disappear when headphones are removed

My built in mac book speakers disappear when I remove my headphone. The system preferences says that they are not present. I've tried restarting and resetting pram. Any other suggestions would be greatly appreciated.

Have you tried blowing into the headphone jack? There could be an accumulation of dust in there.

Pavilion d6 with Beats Audio and Windows 7: the Sound Stops When Headphones are Removed

The sound works fine, then I put in headphones and usually the sound plays fine, though sometimes it stops working after making a repeating sound for a second. When I remove the headphones the sound will not come out of the speakers and if I plus the headphones back in no sound comes out. The only way I can get the sound to work again is to restart my computer.
If I run the sound troubleshooter it doesnt detect a problem. I tried the fix in this thread http://h30434.www3.hp.com/t5/Notebook-PC-Sound-and-Audio/Beats-audio-pavilion-dv6-No-sound/td-p/2169..., but that didn't work. I would really appreciate a solution, thanks a ton!

Hi,
Try the following.
Download the IDT Audio installer on the link below and save it to your Downloads folder.
http://ftp.hp.com/pub/softpaq/sp63501-64000/sp63555.exe
When done, open windows Control Panel, open Device Manager and open up Sound, Video and Game Controllers. Right click the IDT device and select Uninstall - you should also get a prompt to remove the current driver, tick the box to allow this and then proceed with the uninstall.
When done, shut down the notebook by holding down the left Shift key as you click on Shutdown to temporarily prevent a hybrid boot.
Unplug the AC Adapter and then remove the battery. Hold down the Power button for 20 seconds. Re-insert the battery and plug in the AC Adapter.
Tap away at the esc key as you start the notebook to launch the Start-up Menu and then select f10 to enter the bios menu. Press f5 to load the defaults ( this is sometimes f9, but the menu at the bottom will show the correct key ), use the arrow keys to select 'Yes' and hit enter. Press f10 to save the setting and again use the arrow keys to select 'Yes' and hit enter.
Let Windows fully load - it will automatically load an audio driver, but just let this complete. Then open your Downloads folder, right click on the IDT installer and select 'Run as Administrator' to start the installation. When this has completed, right click the speaker icon in the Taskbar and select Playback Devices. Left click 'Speakers/HP' once to highlight it and then click the Set Default button - check if you now have audio.
Regards,
DP-K
****Click the White thumb to say thanks****
****Please mark Accept As Solution if it solves your problem****
****I don't work for HP****
Microsoft MVP - Windows Experience

(1) understanding why Firefox consistently crashes; (2) why Firefox does not acknowledge when "cookies" ARE enabled.

Firefox will crash while I am using the internet...no warning, no apparent reason...just an apology for the crash. Why?
Today, when using an Adobe application Firefox did not recognize or allow the website to recognize that "cookies" WERE enabled. I kept receiving a message that the website could not proceed until same was enabled. Even after several redoing the enabling instructions, the message report the cookies were NOT enabled. Yet, as I write this the screen menu drop down in Tools, Options shows the cookies is programmed and are enabled. Why? How to fix?

Please upgrade your browser Firefox 7 where we fix ton of crashes and freezes:
* getfirefox.com

My Ipod does not charge when I plug it into my computer.

Does anyone know why? I have a 3rd generation 15gb ipod running on a windows computer. It seems to eat up my battery if i try to charge it in my computer.

3rd generation iPods don't charge over USB.

Find and replace in files does not refresh when changes are made

Using RH10, I search for a term with the Find and Replace Options pod. I use the Find Results list as a reference only, and open each file from the Topic List. I do this instead of opening the topics from the Find Results tab because I want to see the WYSIWYG changes. Anyway, I make my edits and delete the search term from each topic. Then, to make sure I have done all the work, I run the search again. I expect to see no or at least fewer matches than before, but I still get some or all of the same results as before, even though I double-check the Design and HTML views of the topics and even check the source of a topic separately in Notepad, all indicating that the search term is gone from the topic.
There is some ridiculous lingering or echo going on. I make sure to select Look in: <Current Project>, and the paths of all the Find Results files are fine. How do you refresh the search so that this echo doesn't occur?
Also, I close the Find and Replace Options pod, reopen it and start the search again, and the same results are there.
Message was edited by: DMilkes

Hi there
To avoid the message about the file being modified, close all topics in the editor before commencing with any find and replace operations. The message is produced because you have the aforementioned topics open in the editor.
As you mention "Find and replace in files", I'm guessing you are referring to version 8. I just opened version 8 and performed a find and replace to confirm. There is a button allowing you to clear all.
On the clicking and dragging to create a link, it's never worked that way. You simply cannot drag from the Topic List pod to do it. But you can from the Project Manager pod. Perhaps you should consider submitting a Wish Form to ask for the ability to click and drag from the Topic List pod to create links.
As far as rearranging your topics into different folders, as long as you do it from inside RoboHelp you shouldn't be destroying any links. RoboHelp will update references for you as you move things around. The only issue is if you are automatically creating your TOC structure based on the project structure. But usually that's a one time shot. From there forward you just manage things using the TOC editor.
Hopefully this helps... Rick
Helpful and Handy Links
RoboHelp Wish Form/Bug Reporting Form
Begin learning RoboHelp HTML 7 or 8 within the day - $24.95!
Adobe Certified RoboHelp HTML Training
SorcerStone Blog
RoboHelp eBooks

IPod does not respond at all when plugged in

Alright, this topic is for people who have had this exact problem only. I don't want to get this confused with other problems and have people trying to help troubleshoot multiple problems and get things mixed up. Here's the problem.
After updating to v1.1.2 of the iPod software, the iPod does not respond when plugged in. The iPod still works fine when not plugged in. It plays music and both the standard and shuffle play modes work accordingly. The problem is when you plug the iPod in, it doesn't charge and it doesn't mount. The orange blinking light does not come on. While plugged in, it works the same way as it does when you're listening to music with it. It's as if the iPod's USB connector is dead. Here is my original post and description of the problem.
Alright, so here's my story. I bought my 512MB Shuffle in April. It has worked perfectly fine since I got it. Last night, I updated to v1.1.2 of the iPod software, clicked no when it asked if I wanted to restart, added some songs to the iPod, then restarted. As of this morning, I went to listen to some music while out for a bike ride, and I was greeted with the red battery light. I thought it was a bit odd since I had left it plugged in overnight. I figured, what the heck, I'll just plug it in and let it charge when I get back. When I got back, I plugged it into my PC and left for a while. I came back later and went to grab my Shuffle and I noticed it was cold, which was unusual after charging for a couple hours. I plugged it back in, a bit frustrated, and it never came up in Windows. I looked at the iPod plugged into the back of my PC (a high powered USB port) and sure enough, no orange light. No lights at all. I can still slide the switch to one of the play modes (standard play or shuffle) and play music for a couple seconds before it stops and says the battery's dead again. It works.. I mean it turns on and plays music, it's just not charging or mounting when I plug it in. I tried multiple computers and USB ports, none of which worked. I would really like some help with this considering it IS my only source of portable music and I'm not going to go pay $50 to talk to tech support or have it sent in for repairs. That's half of what it's worth.
I've tried uninstalling all iTunes/iPod related software from the PC I normally use it on and reinstalling it. That didn't work. I also tried uninstalling again and installing the last known working version of the iPod software, still no results. The only thing I havn't tried is giving it a good beating... Not that I would. Anyways, I hope there's a solution to this that doesn't involve buying a new one.
Here's a rundown of the computers I tested it with.
500MHZ G4 Cube (384MB RAM/Mac OSX Tiger)
400MHZ G3 iMac (384MB RAM/Mac OSX Tiger)
4.2GHZ AMD 64-Bit running Windows XP Service Pack 2 (my PC)
515MHZ Dell running Windows 2000 (256MB RAM)
UPDATE: The BIOS won't recognize the iPod, so it has nothing to do with my computer. Somehow, installing v1.1.2 of the iPod software made it so the iPod itself has USB problems. The iPod works to the extent of playing music and showing the battery charge level. I get no response at all when I plug it in, from the computer or the iPod.
I'm going to have to agree with Philip Harhay on this one. The original 10GB iPod I bought 3 years ago came with a full one-year warranty, no extra charges. I am disappointed to see the Shuffle only coming with a three-month warranty.
------------------------------------------------------------------

Help! I just purchase an iPod Shuffle for my son's birthday and I cannot get the darn thing to show up on my iMac G5. I am running OS 10.4.2 and I have downloaded the latest iPod and iTunes software. When I try to restore my iPod to the factory settings it tells me to plug the iPod into the computer, but it is plugged in. I have tried different USB ports, too. I'm running out of ideas and so is the trouble shooting Apple site. I was hoping someone out there might have some ideas.
It showed up at first and I transferred a few songs from the iTunes to the iPod but I couldn't get them to play, so I plugged it back into the USB and the icon never came up.

Lots of programs does not respond, when opened

Lots of programs does not respond, when they are opened, Apple store, Mail, Photo Booth and VideoConverterPro and some moor.
To close, I have to click on finder first. What to do ?

Please read this whole message before doing anything.
This procedure is a diagnostic test. It’s unlikely to solve your problem. Don’t be disappointed when you find that nothing has changed after you complete it.
The purpose of the test is to determine whether the problem is caused by third-party software that loads automatically at startup or login, by a peripheral device, by a font conflict, or by corruption of the file system or of certain system caches.
Disconnect all wired peripherals except those needed for the test, and remove all aftermarket expansion cards, if applicable. Start up in safe mode and log in to the account with the problem. You must hold down the shift key twice: once when you turn on the computer, and again when you log in.
Note: If FileVault is enabled, or if a firmware password is set, or if the startup volume is a software RAID, you can’t do this. Ask for further instructions.
Safe mode is much slower to start up and run than normal, with limited graphics performance, and some things won’t work at all, including sound output and Wi-Fi on certain models. The next normal startup may also be somewhat slow.
The login screen appears even if you usually login automatically. You must know your login password in order to log in. If you’ve forgotten the password, you will need to reset it before you begin.
Test while in safe mode. Same problem?
After testing, restart as usual (not in safe mode) and verify that you still have the problem. Post the results of the test.

IPod does not turn back on when headphones are plugged in.

Hi all,
In my previous iPod, it would automatically pause a song when the headphones are removed and if the iPod is off, it would automatically turn the iPod on once I inserted the headphone jack.
My 4G iPod for some reason does not turn the iPod on automatically when I insert the headphone jack. Is this normal or is there some setting that I need to change to accomodate this?
Thanks for any help,
Ed

Yep, the problem seems to appear when the iPod has been left to sit for an hour or so. Unplugging the headphone jack will pause the song and after a while the display will cut off. Plugging the jack back in does not turn the iPod back on, however hitting the menu button will turn it on where it was last left.
I could have sworn my previous iPod didn't behave this way; it would come back on when the jack was plugged in.
Ed

Ipod does not pause when headphones are removed

Similar Messages

Maybe you are looking for