Ipod Freezes must reset each time to mount
HI, 8GB nano. Recently, every time I connect my nano it does not mount in itunes and it freezes. I can unplug it, hit the reset (center and menu), and replug it in and it will mount and sync fine. Next time though, same thing will happen. Even seconds after a sync. This is new problem and I can't fix it. Any ideas? My other 1st gen ipod mounts fine. Thanks
M
I have the same problem, also starting immediately after upgrading to itunes 8.
Oddly enough, I had the same issue before, and it turned out to be due to the fact that I was using my boyfriend's iphone USB cable (since it doesn't have the annoying little buttons you have to push in to remove it from the ipod, which require pulling out the earbuds every time I sync, talk about a design flaw!). When I switched back to the nano USB cable, everything was fine for a few months, until I stupidly decided to install itunes 8, and now it freezes every single time I plug it in. I reset the ipod (leaving it plugged in), and when it turns back on, I get a message telling me that an unknown USB device is attached to my computer. I pull the USB cable, plug it back in, and then it syncs normally. I've tried restoring the ipod and reinstalling itunes, neither worked. It is still under warranty, so I may try to get it replaced, but the nearest Apple store is hours away and I've been hoping a software update might help. Any other suggestions would be much appreciated!
Similar Messages
-
I have a new Curve 9360, downloaded google sync, voice, and maps, but not much more. After about 2 hrs or so, all applications including Blackberry ID, google sync, voice, and maps stop updating. When I go to Blackberry ID Account, it gives error "Unable to retrieve your Blackberry ID account information." But after a hard or soft reset all applications work for about 2 hrs. I have already performed a "Factory Reset" with the Blackberry Desktop Software.
It seems like it must be a global setting that gets changed after a few hours each time.
Anyone else have this problem? Any suggestions?
Thanks.Also the os that's installed is the 1st os 7 released if I'm not mistaken and buggy best to update to latest os.
Once update is do not install all 3rd party applications immediatley some maybe incompatible with os 7. Install 1 at a time and test phones response for a few days. -
The last 3 or 4 times I have tried to access my account, it has told me it has been deactivated and I have to reset each time, or give credit card info again. Why is this happening and how do I stop it?
You must contact iTunes support to get the problem resolved.
http://www.apple.com/support/itunes/contact/
If there is a problem with your account or payment info, you cannot
download anything (including free apps or updates) until the matter
is resolved.
In countries where the iTunes Store only sells apps, the accepted payment methods are Visa, MasterCard, and American Express. Other payment types such as gift cards, store credit, monthly allowances, ClickandBuy, and PayPal are not accepted. Depending on your App Store country, prices may be listed in your local currency, US Dollars, or Euros. http://support.apple.com/kb/HT5552 -
How do I save my Home sharing details on Apple TV. It resets each time I leave COMPUTER ...
Welcome to the Apple community.
What makes you think it is resetting, are you sure it is not simply disconnecting. -
IPod 60GB resets each time it turns on?
Is it normal for a 60GB iPod to reset...so the apple logo shows up...each time the ipod is turned on? It's never happened to me before and its annoying. Also, how loud is the ipod's HDD supposed to be, I find that when I tip my ipod from side to side, I hear a faint screeching noise.
After 14 hours of inactivity, the iPod goes into hibernation mode. After this, it will appear to reset when started again.
http://docs.info.apple.com/article.html?artnum=60945
Cheers!
-Bryan -
Passcode must be reset each time return to main menu button is pressed
I am an IT help desk professional and have come across an issue with the Iphone 4. One of our employees recently purchased one and I installed Exchange on it so she could receive business emails. She had no passcode installed on the phone, but due to the sensitive content of our email, when the Exchange profile is installed it automatically forces it. Now, each time she presses the button at the bottom of the phone to get back to the main menu, it requires her to reset her password. We took the forced passcode out of her profile for now but need to find a solution so she can be passcode protected. Has anyone else see this occur??
I am an IT help desk professional and have come across an issue with the Iphone 4. One of our employees recently purchased one and I installed Exchange on it so she could receive business emails. She had no passcode installed on the phone, but due to the sensitive content of our email, when the Exchange profile is installed it automatically forces it. Now, each time she presses the button at the bottom of the phone to get back to the main menu, it requires her to reset her password. We took the forced passcode out of her profile for now but need to find a solution so she can be passcode protected. Has anyone else see this occur??
-
Verizon ONT keeps turning off randomly. I must manually reset each time, help!
As the title states, the ONT will randomly turn off, and in order for me to restore TV and internet, I have to unplug the ONT from the wall, unplug the battery backup, plug the battery backup in again, then plug the ONT into the wall.
I have had THREE technicians out this week, each stating they fixed the problem. Alas, each time, a couple hours after they leave, the ONT shuts off again... it is driving me insane, and I am quickly losing my patience. Has anyone experienced this before? Anyone have any tips as to what I should tell the 4th tech to do in order to fix the problem?Did you restore it as a new phone?
If so, and you're having this issue, best take it to an Apple store to be evaluated. They can test the battery to determine if it's gone bad.
~Lyssa -
Font sizing and Encoding information are reset each time
I am using iSql*plus against a UTF8 database to view multilingual text .. I found that I have to reset the encoding and the size information on the IE browser each time I execute a SELECT statement ...
For example I have select ename from emp ... Now change my encoding to UTF8 and Font size to Large ... Next amend the statement to select one more column say deptno, the sizing and encoding information is reset and I need to set them again .. Is this a known issue ?
nullPeter,
We've managed to reproduce the problem in-house. It doesn't seem to occur in Navigator, but does in IE. I suspect it may be a problem with IE, but I'm not sure. I've logged a bug and it will be looked at.
Thanks for reporting it.
Alison
iSQL*Plus Team -
IMovie freezing at Thumbnails each time
Everytime I open up IMovie, it gets stuck at Generating Thumbnails and never gets done. I've even left it alone for over 24 hours. Even if I close it out and restart the computer, as soon as IMovie starts it goes to generating thumbnails and gets stuck. What should I do?
Thanks
Annmariejay, I think I've worked this out but it's taken me a while.
I had the same problem in that each time I've attempted to open iMovie I was met with the 'generating thumbnails' message, every time, and a freeze for up to two hours. Bloody annoying!! So after trial and error here's what I did and iMovie has now opened for the first time in three days.
1. opened movies/iMovie/iMovieevents and iMovieprojects and removed all films to the desktop - I had about eight folders. Leave the folders but no films in there.
2. I then opened my library folder and opened preferences folder
3. I removed all 'com.apple.imovie.plist' files to the desktop - this didn't make much difference but do it anyway.
4. I then looked through the folder for missed files and found a something called 'com.apple.iMovieApp.p.list.lockfile' and removed it to the desktop.
5. launched iMovie and it worked immediately! Voila!
I've spent a few hours editing and iMovie opening and closing no problem. I just checked that the films I removed to the desktop are all in the events library and they are and are working no problem.
Hope that helps! -
The Imac crashes each time and I must restart it almost every hour! After restart I need to cool the machine otherwise I need to restart more then 5 times
before it starts running again. When I work with pictures there are horizontal stripes on the screen and see some delay in the finder screen. It looks like a video error.
My question is if this is a hardware problem or an OSX system problem? If I want to install Panther should this work in combination with this machine?
Hopefully somebody can help!
Modelnaam: iMac
Modelaanduiding: iMac6,1
Processornaam: Intel Core 2 Duo
Processorsnelheid: 2.16 GHz
Aantal processors: 1
Totaal aantal cores: 2
L2-cache (per processor): 4 MB
Geheugen: 2 GB
Bussnelheid: 667 MHz
Opstart-ROM-versie: IM61.0093.B07If you say cooling helps then that's likely a hardware problem. Maybe even something as simple as too many dust bunnies inside. You'd need to ask on the iMac forum on how to clean inside. Overheating can cause various problems, including video. I guess it could be software, but do you hear the fans racing? I don't know about iMacs but other models will automatically turn fans on at high speed to prevent overheating should the software controlling the fans not run.
Panther? On an Intel Mac? No way. You did mean OSX 10.3 didn't you? 10.6 is Snow Leopard and most people with your machine want to go that direction (or even to Lion 10.7). -
[FlashPro CC & AIR] Icons are reset each time I change the target Air Platform
Hi guys,
I have an annoying bug with my Flash CC : I'm building an Air app and each time I change the target platform (either Android or iOS or Windows) the <icon> tag is cleaned... so I have to set all the icons files again. Each and every time. All the icons.
Is it a known bug ? Is there a fix ? Is it a feature ? I tried to uninstall and clean all the cache, it does nothing. I have Flash CC on my work computer and on my laptop and the problem is on both computers...
I have the latest version of Flash CC and it's not linked to an Air version.
Thanks in advance for your help ! -
Random freeze ups. Must reboot each time.
Random full screen lock with no errors reported using the hardware test disc. Mouse can move on screen (arrow or beach ball) but no clicks or key presses of any kind cause a response. The clock freezes instantly as does video playback. Audio dies altogether (or starts looping) within a few seconds of freeze-up but not quite instantly like screen (except mouse cursor) does. The only way out is by holding power key for 3-4 seconds until MacBook Pro shuts off. Force quit popup box never comes with commandoptionesc. Even right now I'm holding my breath that I can post this before the next occurrence since it has become a daily event.
This just started about 30 days ago. Never had this happen in Tiger but probably unrelated. My thing is that I'm out of warranty by self-upgrading the internal hard drive awhile back. Hoping someone can help with a diagnosis. At first thought maybe it was time machine or boot camp causing the freeze ups, but I ruled them out. Although left and right fans almost always stay at 1k RPM, I'm now wondering if maybe there's a heat issue or video card (ATI) issue - but those are really just guesses. I've done a clean install and recovered only some files back from time machine. I've done a PMU reset and tried the factory ram only. Nothing seems to work, plus booting from the hardware test shows no hardware errors. Booting from leopard to run fix disk and permissions also did nothing. Keeping in mind that I've voided my warranty can anyone suggest next steps? I'm not great at understanding console messages but nothing seems to show in logs at exact time of freeze up that I can tell. For the record Software updates says I'm current including firmware stuff too. Never had an issue like this since OS 7 when multi-finder was introduced. This is making me nuts, so if you'll indulge me, here are my machine specs...
Hardware:
Hardware Overview:
Model Name: MacBook Pro 15"
Model Identifier: MacBookPro1,1
Processor Name: Intel Core Duo
Processor Speed: 2 GHz
Number Of Processors: 1
Total Number Of Cores: 2
L2 Cache: 2 MB
Memory: 2 GB
Bus Speed: 667 MHz
Boot ROM Version: MBP11.0055.B08
SMC Version: 1.2f10
Sudden Motion Sensor:
State: Enabled
Network:
AirPort:
Type: AirPort
Hardware: AirPort
BSD Device Name: en1
Has IP Assigned: Yes
Ethernet:
Type: Ethernet
Hardware: Ethernet
BSD Device Name: en0
Has IP Assigned: No
Bluetooth:
Type: PPP (PPPSerial)
Hardware: Modem
BSD Device Name: Bluetooth-Modem
Has IP Assigned: No
FireWire:
Type: FireWire
Hardware: FireWire
BSD Device Name: fw0
Has IP Assigned: No
Software:
System Software Overview:
System Version: Mac OS X 10.5.1 (9B18)
Kernel Version: Darwin 9.1.0
Time since boot: 18 minutes
ATA:
ATA Bus:
MATSHITADVD-R UJ-857:
Model: MATSHITADVD-R UJ-857
Revision: HAEA
Serial Number:
Detachable Drive: No
Protocol: ATAPI
Unit Number: 0
Socket Type: Internal
Low Power Polling: Yes
Audio (Built In):
Intel High Definition Audio:
Device ID: 0x83847680
Audio ID: 2
Available Devices:
Headphone:
Connection: Combo
Microphone:
Connection: Internal
Speaker:
Connection: Internal
Line In:
Connection: Combo
S/P-DIF Out:
Connection: Combo
S/P-DIF In:
Connection: Combo
Bluetooth:
Apple Bluetooth Software Version: 2.0.0f20
Diagnostics:
Power On Self-Test:
Last Run: 1/26/08 7:37 PM
Result: Passed
Disc Burning:
MATSHITA DVD-R UJ-857:
Firmware Revision: HAEA
Interconnect: ATAPI
Burn Support: Yes (Apple Shipping Drive)
Cache: 2048 KB
Reads DVD: Yes
CD-Write: -R, -RW
DVD-Write: -R, -RW, +R, +RW
Write Strategies: CD-TAO, CD-SAO, DVD-DAO
Media: Insert media and refresh to show available burn speeds
FireWire:
FireWire Bus:
Maximum Speed: Up to 400 Mb/sec
Graphics/Displays:
ATI Radeon X1600:
Chipset Model: ATY,RadeonX1600
Type: Display
Bus: PCIe
PCIe Lane Width: x16
VRAM (Total): 128 MB
Vendor: ATI (0x1002)
Device ID: 0x71c5
Revision ID: 0x0000
EFI Driver Version: 01.00.068
Displays:
Color LCD:
Display Type: LCD
Resolution: 1440 x 900
Depth: 32-bit Color
Built-In: Yes
Core Image: Hardware Accelerated
Main Display: Yes
Mirror: Off
Online: Yes
Quartz Extreme: Supported
Display Connector:
Status: No display connected
Memory:
BANK 0/DIMM0:
Size: 1 GB
Type: DDR2 SDRAM
Speed: 667 MHz
Status: OK
BANK 1/DIMM1:
Size: 1 GB
Type: DDR2 SDRAM
Speed: 667 MHz
Status: OK
Serial-ATA:
Intel ICH7-M AHCI:
Vendor: Intel
Product: ICH7-M AHCI
Speed: 1.5 Gigabit
Description: AHCI Version 1.10 Supported
Hitachi HTS541616J9SA00:
Capacity: 149.05 GB
Model: Hitachi HTS541616J9SA00
Revision: SB4OC70P
Native Command Queuing: Yes
Queue Depth: 32
Removable Media: No
Detachable Drive: No
BSD Name: disk0
Mac OS 9 Drivers: No
Partition Map Type: GPT (GUID Partition Table)
S.M.A.R.T. status: Verified
Volumes:
disk0s2:
Capacity: 148.73 GB
Available: 57.35 GB
Writable: Yes
File System: Journaled HFS+
USB:
USB High-Speed Bus:
Host Controller Location: Built In USB
Host Controller Driver: AppleUSBEHCI
PCI Device ID: 0x27cc
PCI Revision ID: 0x0002
PCI Vendor ID: 0x8086
Bus Number: 0xfd
Built-in iSight:
Version: 1.84
Bus Power (mA): 500
Speed: Up to 480 Mb/sec
Manufacturer: Micron
Product ID: 0x8501
Vendor ID: 0x05ac (Apple Computer, Inc.)
USB Bus:
Host Controller Location: Built In USB
Host Controller Driver: AppleUSBUHCI
PCI Device ID: 0x27c9
PCI Revision ID: 0x0002
PCI Vendor ID: 0x8086
Bus Number: 0x3d
USB Bus:
Host Controller Location: Built In USB
Host Controller Driver: AppleUSBUHCI
PCI Device ID: 0x27ca
PCI Revision ID: 0x0002
PCI Vendor ID: 0x8086
Bus Number: 0x5d
IR Receiver:
Version: 1.09
Bus Power (mA): 500
Speed: Up to 12 Mb/sec
Manufacturer: Apple Computer, Inc.
Product ID: 0x8240
Vendor ID: 0x05ac (Apple Computer, Inc.)
USB Bus:
Host Controller Location: Built In USB
Host Controller Driver: AppleUSBUHCI
PCI Device ID: 0x27cb
PCI Revision ID: 0x0002
PCI Vendor ID: 0x8086
Bus Number: 0x7d
Bluetooth USB Host Controller:
Version: 19.65
Bus Power (mA): 500
Speed: Up to 12 Mb/sec
Manufacturer: Apple, Inc.
Product ID: 0x8205
Vendor ID: 0x05ac (Apple Computer, Inc.)
USB Bus:
Host Controller Location: Built In USB
Host Controller Driver: AppleUSBUHCI
PCI Device ID: 0x27c8
PCI Revision ID: 0x0002
PCI Vendor ID: 0x8086
Bus Number: 0x1d
Apple Internal Keyboard / Trackpad:
Version: 0.60
Bus Power (mA): 500
Speed: Up to 12 Mb/sec
Manufacturer: Apple Computer
Product ID: 0x0217
Vendor ID: 0x05ac (Apple Computer, Inc.)
AirPort Card:
AirPort Card Information:
Wireless Card Type: AirPort Extreme (0x168C, 0x86)
Wireless Card Locale: USA
Wireless Card Firmware Version: 1.2.2
Wireless Channel: 8I think the fan defaults to 1,000 rpms. Only thing I've found that seems to help is keeping the fan speeds at about 3,000 rpms. No more freeze ups (except one) when I keep the fan speed up a bit.
http://homepage.mac.com/holtmann/eidac/software/smcfancontrol2/index.html -
I have a Sonos system with an ipod dock and was experiencing problems when using my ipod. The people at Sonos suggested resetting my ipod, so I did. Now, unfortunatey, my ipod isn't working properly. When I connected it to my itunes it said that it was in recovery mode and should be restored. I restored it and a message said it would appear in my itunes. But it just keeps saying that it needs to be restored. I've tried removing my itunes software and reloading it again but nothing changed.
Disabled
Place the iOS device in Recovery Mode and then connect to your computer and restore via iTunes. The iPod will be erased.
iOS: Wrong passcode results in red disabled screen
If recovery mode does not work try DFU mode.
How to put iPod touch / iPhone into DFU mode « Karthik's scribblings
For how to restore:
iTunes: Restoring iOS software
To restore from backup see:
iOS: Back up and restore your iOS device with iCloud or iTunes
If you restore from iCloud backup the apps will be automatically downloaded. If you restore from iTunes backup the apps and music have to be in the iTunes library since synced media like apps and music are not included in the backup of the iOS device that iTunes makes.
You can redownload most iTunes purchases by:
Downloading past purchases from the App Store, iBookstore, and iTunes Store
If problem what happens or does not happen and when in the instructions? When you successfully get the iPod in recovery mode and connect to computer iTunes should say it found an iPod in recovery mode. -
Ghostery settings not saved, but must be reset each time I open Firefox.
For several weeks now I am obliged to reset all of the Ghostery settings every time I open Firefox 33.1.1. The Ghostery webpage pops up along with my homepage and all of my prior settings have been removed. The folks at Ghostery tell me the problem is at the Firefox end. Can anyone help resolve this?
With the help of a friend I had tried that and Malwarebytes still did not detect the threat. At that point I bailed and got my computer wiped and all new software installed. I read a review on AVG antivirus that praised it for
its' sensitivity but cautioned against "false positives" for that reason. I am beginning to wonder if it was not a false positive since it only came up when opening Firefox, but not in the full AVG scan.
By the way I imported book marks from Firefox into Internet explorer which had never shown that warning and it began to show the warning on opening. It has me puzzled to say the least but thanks for your suggestions. -
ICloud password not accepted, intermittent failure and must be reset each time
So, my wife is becoming manic depressant when she tries to use her phone, computer, whatever... on icloud. It will work fine for a week or two, then suddenly the password for the same account she has had no problem with for the last 4 years doesn't work any more. I then get called in to reset her password, re-sign in all of her devices, and she and I are happy once again. This has happened a ******** amount of times, (more than 10). I have went through the entire process of resetting all of the security questions... blah, blah... tech support... turn off, sign out all devices, blah blah... turn on, sign back in, on and on... update the computer, soft reset, hard reset, "upgrade" to the new stupid operating system that she really hates, blah blah, update the phone to an even worse OS,... on and on. Honest. I've tried everything. Everything is the latest model, and software version.
Does anyone out there actually know how to fix this intermittent problem? There is no solid pattern to the time intervals. It can happen within hours, or weeks of me resetting the password and signing in.
Lately, I have spent more intimate time with my wifes Apple devices than her, and this is very disturbing for me. (and her)Hi,
Whilst Apple IDs that end in either @mac.com or @me.com they registration pages do not tell you that if you are going to be using it as an AIM Screen Name the password has to be 16 characters otr less. (This is an AIM server limit)
At some point you will need to update the password.
10:08 PM Friday; March 23, 2012
Please, if posting Logs, do not post any Log info after the line "Binary Images for iChat"
iMac 2.5Ghz 5i 2011 (Lion 10.7.3)
G4/1GhzDual MDD (Leopard 10.5.8)
MacBookPro 2Gb (Snow Leopard 10.6.8)
Mac OS X (10.6.8),
"Limit the Logs to the Bits above Binary Images." No, Seriously
Maybe you are looking for
-
How to get back "DCIM" folder and lost photos?
Do you know something about "DCIM" folder? Yesterday, I just accidentally deleted this folder and found all my phone photos disappeared. Can I get back this folder, especially the inner phone photos? Do you have any idea? I need your help!
-
Is there any setting in ODS to accelerate the data loads to ODS?
Someone mentions that there is somewhere in ODS setting that make the data load to this ODS much faster. Don't know if there is kind of settings there. Any idea? Thanks
-
Hi, I want to convert the date like 'now' to Time Object in a specific format ("yyyy-MM-dd hh:mm:ss") I wrote the following code. Time date; date = (Time) 'now'; Time test = (Time) date.format(mask : "yyyy-MM-dd hh:mm:ss"); logMessage("Result: " + te
-
Hi, If I open up the print dialog box within PS, and click on the Color Handling dropdown and select Printer Manages Color, I am reminded to open the Print Settings dialog and turn off the the printers color management. I do this and click OK, and th
-
Bulk Insertion through a procedure
There are 6 Million row in core_business.cb_insured_person_detail@pcba which i want to insert into same table on other node. I can not use simple simple Insert into ....... Select * from ...... because of some exception. This procedure is working but