IPod goes into standby and immediately wakes without unlucking it

I have some iPods which I can't always put in standby the first time.
When i press the topmost button it goes in standby for about a second and then it wakes again
I have a few iPods (all touch 5g) on which this occurs.
Other symptoms of these devices are:
Takes 10 - 15 seconds after wake from standby before touch is reactive.
After a hard reset (holding both buttons until Apple logo appears) reopens previously closed apps
iPod hangs from time to time, even with no apps opened
There is 10Gb + available on the device so this should available space should not be a problem
Is there anything I can change in settings to solve this?

- Reset all settings
Go to Settings > General > Reset and tap Reset All Settings.
All your preferences and settings are reset. Information (such as contacts and calendars) and media (such as songs and videos) aren’t affected.
- Restore from backup. See:
iOS: Back up and restore your iOS device with iCloud or iTunes
- Restore to factory settings/new iOS device.
If still problem, make an appointment at the Genius Bar of an Apple store since it appears you have a hardware problem.
Apple Retail Store - Genius Bar

Similar Messages

Phone goes into standby and wont turn off after update!!! please help me as hate it

On Friday I turned my phone off as per usual and turned back on in the morning to find the phone totally different.
The red lock button now only sends the phone into like a sleep mode, and i cant find any where to turn it off.
The screens keep fading down and I have re set the backlight to not dim but some thing is over riding it.
I used to love my phone and now hate it so much, is there a way of booting this update off my phone and putting it back to how it was. I tried to restore and its the same and then tried to put the phone back to previous settings I had stored on my lap top but again nothing.
I now have some new blackberry software on the lap top too which now does not even recognise my phone and there for the past restore points I had.
My daughters bold 9700 does the same thing now too, please please help

Hiya!
Blackberry doesnt actually "turn off" it only goes into a standby mode (press and hold the end call button). To fully power it down, you would perform a battery pull.
1). Please thank those who help you by clicking the beside the 'Reply' button.
2). If your issue has been solved, please resolve it by marking "Accept as Solution" on the correct post!
3). Remember to have fun! We are all in this together!
4). Follow me on

8900 keeps going into standby and the only way to unlock is to press the power button?

Hi,
I Recently had my T-Mobile blackberry unlocked for my wife to use. It is now on Virgin. I have upgraded the software and everything is working well with the exception that the phone keeps going into some kind of stand by. It isn't the normal keypad lock, the unlock button wont unlock it, you have to press the red power button for a few seconds to wake it up.
It appears to be on a timer as it locks after about 2 minutes and goes to a black screen. It will happen in the middle of typing a text or whatever you are doing and when you press the power button to unlock it, it then takes you back to the home screen.. Very annoying!
I have gone through all the options and cant find anything to stop it. The auto on/off if off. Password is disabled with security time out set to 30 mins.
Any help would be appreciated
Thanks

Managed to sort the problem by roling back the software to version 4.6.1
Thanks for all your help.....??

2008 MacBook pro freezes then when try to restart goes into hibernation and cannot wake it! Any ideas?

Recent upgrade of ram. MacBook pro now freezes and when attempt restart does not shutdown but seems to go into sleep or hibernate and cannot get started again! Help!

Sounds like faulty ram, can you go back to the former ram and see that it starts ok? If it does contact the supplier of the memory and get an exchange set.

My 3050 J610 printer goes into standby or sleep mode and then I cannot print docs to it wirelessly

Everytime I do not print something for a few hours, my printer goes into standby or sleep mode. When it does this, it cannot be used to print from my laptop or android to it. Is there a way to set this up so that it doesn't "go to sleep" and it is always available to me to print with. I like the printer, but it seems kind of off that you cannot print on it wirelessly and it is considered a WIRELESS printer. That's the only reason I bought it and now I can't even use it without walking downstairs and turning the printer back on again. If I wanted to do that every time I would just print from my main computer!
Thanks,
Ashley
This question was solved.
View Solution.

Ok, I know this thread is a little old, but it would not allow me to start a new one, since I am new. I am having the same issues with my 3050 J610 as everyone else. It makes you think there is a wireless connection problem, but that is not the case. The printer goes into a standby mode and there is no way to bring it out of it, unless you cycle the printer. The panel buttons will still work, you just lose the ability to print wirelessly.
I have had my 3050 J610 in two different rooms, master bedroom and basement office. Both areas work well when it is connected and awake. After a while of inactivity, it goes into standby mode and cannot print wirelessly. Here are steps I have taken so far:
When the printer goes into standby and will not print wirelessly, I have check to make sure there is still a connection between the router and the printer - There is
I have set a static Id for the printer at .210
Cycling the printer brings the connection back instantly.
The front panel buttons work just fine when it does not have connectivity
In the basement, the machine has excellent signal and connection.
I have checked the recommendations in this thread, and like others, there are no options under the advanced tab of the maintenance page. The problem is a standby or sleep issue. When this arises, it has connection to the router, but the wireless computer does not have connection to the machine. I know when it was in the bedroom, the light would blink 3 or 4 times now and then throughout the night. We need a way to turn off the standby, or bring the machine out of standby mode. It is not an issue of the router, channel, interference, or software. It is the sole issue of standby or sleep modes. I have been pulling my hair out for almost two years over this issue. I swore I would not buy another HP product after the problems I had with a printer and laptop. But I thought I would give HP another chance.

My iPhone turns off whenever it goes into standby mode and has to be turned back on to work

My iPhone turns off whenever it goes into standby mode and has to be turned back on to work

That's normal behavior. It turns off automatically in order to preserve the battery. Pushing the On/Off button turns it on immediately. This also requires entering the passcode and prevents the phone from being accessed by anyone but you.

On my ipad mini, when I delete an email from the inbox (and it goes into Trash), it immediately deletes that email from the server (ATT/Yahoo). I've called support for both ATT and Apple and can't find a way to have the emails remain on the server.

On my iPad Mini, when I delete an email from the inbox (and it goes into Trash), it immediately deletes that email from the server (ATT/Yahoo). I've called support for both ATT and Apple and can't find a way to have the emails remain on the server.
My husband and I share an email address and if he misses a day checking email on his notebook, he doesn't receive the items that I have sent to Trash on my iPad Mini.
Appreciate suggestions.
[The curious thing is, if I "move" the deleted emails from Trash on my iPad Mini into the Inbox, I can go to my notebook, open my online email and they are back in my ATT/Yahoo Inbox.]

Is your Yahoo account set up as POP3 or IMAP?

My new macbook pro retina randomly goes into standby mode

My new macbook pro retina randomly goes into standby mode. I have to close the screen and wait a few seconds and re-open it in order for it to come back on.
Sometimes it immediately goes back into standby mode again after closing and reopening the screen. I have checked the battery level everytime, and it has never been below 40% when this occurs. Is this a Mountain Lion issue?

Well I fixed my problem.
I took it into the Apple store. Even without the other two monitors they were able to recreate the problem. One symptom (I had) was that one of the Hot Corners was set to Disable screen saver. If you then put your cursor there, you'd go into screen saver mode. Change the setting to another corner and the problem follows you there.
The Apple person at the Genius bar logged out as me and back in as test and same problem. He tried some stuff and finally said I needed to wipe the drive and reinstall the OS (Lion). I'd only had the machine for 12 hours and had just migrated my data to it, so I didn't mind doing that. I did it at home.
Problem solved.
BUT... then I reinstalled the driver for my EVGA UV Plus 19 (most current drivers) and bingo problem back. Uninstall. Problem gone. I'm now using mini display port to DVI for one monitor and HDMI for the other I think the machine is a bit warmer this way (versus using a USB to the EVGA device) but at least it's not sleeping all the time. Someone might say "it (the heat) is your imagination" or something else. Or someone might say "use the other thunderbolt port for another mini-display port to DVI" but I need that for the LAN... c'est la vie.
Maybe I'll write to evga and see what they say. Maybe they'll fix their driver and/or Apple will fix it.

T400 goes into standby right after being woken from standby

Hi, I have a T400. When I wake it up from standby by pressing the Fn key, it wakes up, then automatically goes into standby again. I can still wake it using the Fn key but I am afraid it might be stuck in a loop.
Any ideas where the bug could be?

How do you send the machine into standby?
W520: i7-2720QM, Q2000M at 1080/688/1376, 21GB RAM, 500GB + 750GB HDD, FHD screen
X61T: L7500, 3GB RAM, 500GB HDD, XGA screen, Ultrabase
Y3P: 5Y70, 8GB RAM, 256GB SSD, QHD+ screen

Satellite P10 automatically goes into Standby after 15 minutes

My Satellite P10 automatically goes into Standby after 15 minutes. This is a setting that is controlled by the Toshiba Power Management settings, or the Toshiba Console.
When I change the settings there the system still goes into Standby after 15 minutes. When I go to Control Panel/Performance and Maintenance/Power Options, it tells me to go to the Toshiba Power Management to change the settings, but I can still see the settings in grey stating 15 minutes standby time.
But in the Toshiba Power Management I can't seem to be able to ajust Standby settings so that they actually work. There must be a trick to it..
Can anyone help me figure it out?
Thanks a lot,
Lerak

Thank you for your replies. As I now understand it there are 3 power management utilities fighting for control of the power management settings:
1) The windows OS power options("Power Option Properties, from the control panel/performance and maintenance/power options);
this utility is overridden by:
2) Toshiba Power management;
and
3) the "power save modes", activated by pressing the Function key and the F2 key, which in turn can override the Toshiba Power management.
If this last Function/F2 combination is used to change the power save modes, the windows OS power settings (which are shown in grey and cannot be changed because this is overridden by the Toshiba Power management) DO actually change.
Hold down the Function key (Fn) and press F2, holding down the Fn key. Each time you then press the F2 key again you scroll down the different "Power Schemes". The last mode is called: Toshiba Power Management. One would think that by choosing this setting the Toshiba Power management utility would effectively take over control of the power settings. Unfortunately this does not seem to be the case..
At least using this last option provides a workaround. Some of the "Power Schemes" disable the standby options.

Mac Pro goes to sleep and wont wake up

Any idea how to stop the Mac from freezing up when it goes into sleep mode?
First the screen saver comes on and then after a way it goes into hibernation and then can't be woken.
It use to wake but suddenly decided not to. Nothing's changed.

Well, as you can see from the long discussion on Creative Cow, the XD Cam issue is complicated and seems to be a hardware issue with Mac Pros. Disconnecting the fibre channel card seemed to have worked for one person. I haven't got one of those as far as I know! But then my crashes aren't as constant as his and seem connected, in my mind, with the odd way FC garbles the aspect ratios of Ex 1 footage, especially if mixed with filters and other codecs on the same time line... but some people swear it's the hardware not the soft that's the problem.
Anyway, I've had the hardware... RAM, Disk issues etc... all triple checked out and can't find a problem.
But still Finder takes six seconds to find anything and I think that has caused some crashes.
It doesn't seem to like Soundtrack Pro at all! (You can find a mixed bag of experiences on that issue as well.) And Motion works a little bit too jittery for my liking.
It might be that there are several different flavours of mother board, some not as geared up to this software as others. That's my theory at the moment. The only way to check is to stick my hard drives into the machine of someone who says they don't have any problems.

New PC build - randomly goes into standby mode, cycles, cant stop it? :(

Well...
Got my new PC runnin....loving it, but all of a sudden.....it started doing this weird thing where it will (while in the middle of use) just go into standby and when I move the mouse itll come back and just cycle back into standy, I cant stop it. I havent installed anything new that I know if....Its a new build...
K8N neo4-f
2x512 VS corsair
pci-e 6600 128 albatron video
raid 1 - 2 80 WD sata drives
new PS - vigor 450
Coolermater case (cavalier)
I think thats all that you would need.....sorta weird, never seen this before....anyone?

no timing , IE it happened last night and i got it outte the cycle, havnt rebooted and its fine today, so it hasnt done it yet....its so random....
I didnt have the 350ps in long enough to know, I got my replacment with a day or so.
its not after xx minutes, or whatever...its totally random....I mean something is triggering it but its RANDOM till I figure out what it is..
Though it was my media portal htpc tv software but I checked that all out and that doesnt seem to be it...
so weird.....
again today its ok.....itll just outta the blue do it..

IPod keeps flashing and flickering into standby and then on and then standby again.

So the ipod is a 2g model. I bought it off of eBay for $34. Thought it was a good deal when I saw it. Now I'm not so sure.
Everytime I press the sleep button, it goes into a berserk flashy rage with its standby. While its doing this, if I press the home button it flashes and takes a screenshot and then continues to do its flashing.
It is 2nd Gen so it has 0 warranty. 0. Cannot take this and get it fixed, need to do it myself. I am not rich :C

Try:
- iOS: Not responding or does not turn on
- Also try DFU mode after try recovery mode
How to put iPod touch / iPhone into DFU mode « Karthik's scribblings
- If not successful and you can't fully turn the iOS device fully off, let the battery fully drain. After charging for an least an hour try the above again.
- Try on another computer
- If still not successful that usually indicates a hardware problem and an appointment at the Genius Bar of an Apple store is in order.
Apple Retail Store - Genius Bar

IPod goes into recovery mode when plugged in, and forces me to restore

Basically what is written above ^^ is what is happening to my iPod Classic 80GB. It hasn't done this until recently, and every few days or so when I go to sync new songs onto my iPod, it goes into recovery mode and says that the iPod must be restored. Now, normally this wouldn't be a problem, but when you have an 11,000 song library that takes around 4 hours or more to sync, it gets really under your skin.
I'm running Windows Vista, any help?

I just purchased a Classic iPod, and two days later it is stuck in this restore loop. The iPod worked fine until the restore was complete. When unplugged from the computer, it responds fine, but now cannot sync at all to put media on the device.
Current machine is WinXP SP2 (work machine). It is also happening on Win7 desktop, 13inch Macbook (OS 10.6.3), and Mac Mini (OS 10.6.3)(personal machines).
Does this appear to be a faulty device?

When i plug my ipod touch (4th gen) into my car usb port the ipod goes into repeat mode

Why is it that when I plug my ipod touch into the USB port of my Peugeot 508SW that the device goes into repeat mode and the same song is played continuosly?

Hi lllaass
The car handbook certainly states that Ipods can be connected although it doesn't specifically mention which operating systems are supported. The car system is recognising the ipod and playing one tune continuously but you cannot switch it to a different song.
Geordietommo

IPod goes into standby and immediately wakes without unlucking it

Similar Messages

Maybe you are looking for