IPod IEEE 1394 SBP2 Device Driver

Hi, prior to upgrade to iTunes 5.0 I could see my iPod as a disk drive in Explorer (Win XP). Now, in the device manager, I get a yellow exclamation point under Disk Drive > "Apple Computer_Inc. iPod IEEE 1394 Device" as the driver is not installed or not available. Can anyone point me to where I can obtain this driver? Thanks much!

Hi,
I dun remember having to install any driver, actually the driver comes bundled with iTunes... did your new iTunes installation workd properly? a reinstalll might help solving your problem

Similar Messages

Apple Computer.ipod IEEE 1394 SBP2 device

has anyone overcome this prob. Device manager under drives has a drive with a yellow exclamation mark. (usually means update driver)
I have latest itunes and ipod software. My doc connector (firewire) goes fine with a G4 ipod, but not my G3. so my firewire is compatible.
Because the ipod isnt being picked up by windows properly i cant restore my ipod.

Go into Device Manager and delete the firewire device driver.
Reboot the computer and Windows will install a new one and everything should work as normal.

IPod Nano 8G - Win7 - Device driver software wat not successfully installed

Hi,
Just got my first Apple iPod Nano 8G (4th) and has installed iTune 9.0.2 (64bit) on my Win 7 Ultimate x64. But I am not able to connect iPod nor Sync with iTune successfully even after reinstall/reboot many times with the same problem.
After the installation of iTune accomplished, I plug USB adapter into PC, then Win7 detected and started to install the driver for the hardware, but got "Device driver software wat not successfully installed" as a result.
Then I went to Device Manager tring to install the driver manually for "Apple iPod USB Driver", but finally I failed again and got "Windows cannot verify the digital signature for the drivers required for this device....", I think this is the software problem, please kindly advise, thanks a lot!

First, my officejet 4500 all-in-one installed and is working perfectly with wireless; however, I have for months still/have been getting the error/uninstall window continuously, telling me install was not successful, but again, printer, scanner, etc., working fine! But this "the installation was not successful" window is ALWAYS up or if I ctrl-alt-del and get it to end now, it comes back up; I have even let it do its thing, finish, restart, but it ALWAYS comes back up, trying to find a solution, etc. BUT MY PRINTER IS WORKING FINE! Please help me get rid of this; also, the file that it puts on desktop to troubleshoot, etc then delete afterward, I have deleted it, but this "unsuccessful" keeps trying to uninstall, reinstall; and as I said, actually went through all the steps to get it gone (printer working fine) but it will not go away! Thanks. ajm

NI_IMAQ IEEE-1394 bug?

I am starting to familiarize myself with the new v2.0 IEEE-1394 firewwire camera driver VI's and have been working with the property nodes that have replaced the IMAQ1394 Attribute & Attribute Inquiry VIs. I have managed to build a VI that will quite repeatably crash LabVIEW.
It requires:
1) a query of a camera attribute property that is recognized by the property node but not by the camera.
2) a subsequent query of another camera attribute property.
Has anyone else seen this?
An example (for LV 7.0, IEEE-1394 v2.0.0) is attached.
Attachments:
Crash LabVIEW.zip ‏27 KB

Hello Warren,
Thank you for using our discussion forums. I have taken a look at your VI and seen similar behavior as you described. I noticed that if you remove the bundle by name from the case structure the problem seems to disappear, let me know if you see a similar behavior. Otherwise, I am trying to investigate the problem and will get back with you as soon as I have any updates. Thank you for your patience and have a great day!
Regards,
Nipun M
Applications Engineer
National Instruments

Ni IMaq IEEE-1394 v2.0 plug/unplug/enumeration

The IMaq IEEE-1394 v2.0 Driver contains some new missed function's espec. the Camera plug/unplug and enumeration.
I can't find any example, how to use this functions correctly. The Cam. plug/unplug functions are impl. by the IMAQ1394 Occurence Config. This Vi needs a valid Session ID, but is there none camera attached or the valid Cam. are detached, this Vi fails.
In the future of my project, there are up to 15 Camera's attached, based on two PXI-8252 1394 Host adapters run's under Lv7.1-RT
regards
M.Funke
Applications Engineer

Dear Mr. Funke,
as starting point you can use the programming model of the imaq example ll occurence vi's, that ship with LabVIEW. Implement the imaq 1394 vi's in a similar order. Place a loop, in which you wait on the occurence.
Information how the imaq 1394 camera driver assigns interface numbers:
camX (where X is an integer, and the first one is 0) is the interface name and is specific to a single camera.
On Windows, the camera file is created when imaq1394CameraOpen is called (either through MAX or programmatically), and the imaq1394.ini file is updated. The imaq1394.ini file is created when the first camera is initialized. You can call imaq1394 Init with the interface name.
The camera order (cam0 vs. cam1) is determined by uuid (unique universal identifier) of camera. The lowest uuids are first. So if you plug in a camera, it will be cam0. If you plug in another one, it could be cam0 or cam1 depending on its uuid. If you have two cameras plugged in and you unplug cam0, cam1 will become cam0.
Regards,
Philippe Goetz
Applications Engineer, National Instruments

Old iPod mini can't be recognized after formatting, and iTunes 'Apple Mobile Device Driver not found.'

My roommate gave me an old iPod Mini a few days ago. It was working fine 'til I plugged it into my computer and it asked me to format it. I did, and now it cannot be recognized by iTunes or my computer. My computer views it as a "removable disk" which cannot be accessed. In devices, it is listed as an Apple iPod though, so I'm hoping not all is lost. I have tried many quick fixes I've read on internet (including changing disk letter) but to no avail. I have reinstalled the new iTunes and now that is telling me it has not installed properly, and when I ran diagnostics, it reads that the Apple Mobile Device Driver not found. I will copy & paste all the info from the diagnostic run below, and if anybody can help me with my new (old) iPod, I'd be everly greatful!
Thanks!!
Microsoft Windows 7 x64 Home Premium Edition Service Pack 1 (Build 7601)
TOSHIBA Satellite L775D
iTunes 11.0.1.12
QuickTime 7.7.3
FairPlay 2.2.32
Apple Application Support 2.3.2
iPod Updater Library 10.0d2
CD Driver Not Available
CD Driver DLL 2.1.3.1
Apple Mobile Device 6.0.1.3
Apple Mobile Device Driver not found.
Bonjour 3.0.0.10 (333.10)
Gracenote SDK 1.9.6.502
Gracenote MusicID 1.9.6.115
Gracenote Submit 1.9.6.143
Gracenote DSP 1.9.6.45
iTunes Serial Number
Current user is not an administrator.
The current local date and time is 2013-01-08 11:16:27.
iTunes is not running in safe mode.
WebKit accelerated compositing is enabled.
HDCP is supported.
Core Media is supported.
Video Display Information
ATI Technologies Inc., AMD Radeon(TM) HD 6520G
**** External Plug-ins Information ****
No external plug-ins installed.
**** Device Connectivity Tests ****
iPodService 11.0.1.12 (x64) is currently running.
iTunesHelper 11.0.1.12 is currently running.
Apple Mobile Device service 3.3.0.0 is currently running.
Universal Serial Bus Controllers:
Standard OpenHCD USB Host Controller. Device is working properly.
Standard Enhanced PCI to USB Host Controller. Device is working properly.
No FireWire (IEEE 1394) Host Controller found.
Most Recent Devices Not Currently Connected:
iPod mini running firmware version 1.4.1
Serial Number: JQ******S42
<Edited By Host>

OMG same thing here; rather annoyed and now have set up accounts on 2 comps(both 64 vista ultimate); about to try my 32 bit vista on my lappy; we'll see... i don;t have high hopes thoush.
What i knew about iPhone before buying it:
What You Need
To use iPhone, you need:
A new two-year wireless service plan with AT&T
A Mac or a PC with a USB 2.0 port and one of the following operating systems:
Mac OS X version10.4.10 or later
Windows XP Home or Professional with Service Pack 2 or later
Windows Vista Home Premium, Business, Enterprise, or Ultimate edition
iTunes 7.3 or later, available at www.itunes.com
An iTunes Store account
An Internet connection
You must be at least 18 years old to open a new AT&T wireless account. You will need a
major credit card to open a new iTunes Store account.
Yeahyeah check all that stuff;
Oh well; just when i thought i'd finally cross over to the beautiful packaging of APPLE. I remember in design school that form follows function. Thanks.
Windows Vista

T61p - IEEE 1394 (Firewire) port does not show up in device manager in Windows 7 x64

I have a T61p. On the front, in the left corner, right next to the wireless on/off switch, is a IEEE 1394 (Firewire) port. However, if I plug anything into it, it's not recognized by Windows, and if I go into the device manager in Windows, there is no IEEE 1394 host manager or ports or anything listed there.
I have rebooted and gone into the BIOS, and I don't see anything in there about 1394 either. Is the port there, but the hardwire inside is missing? Do I need to enable it somehow?

Let me clarify that. I have something in the device manager called "SD Host Adapters", and under that "SDA Standard Compliant SD Host Controller". That thing has a Microsoft driver.
However, under "IDE ATA/ATAPI contollers", I do see "Ricoh Memory Stick Contoller", "Ricoh SD/MMC Host Contoller", and "Ricoh xD-Picture Card Contoller".
I also have "PCMCIA adapters" that has "Ricoh R/RL/5C476(II) or Compatible CardBus Contoller".
So, it would seem I have the right drivers for the card reader, I'm just missing anything for the IEEE 1394 contoller...

IEEE 1394 Driver update for Windows?

Can't get IPOD updated....again.
Running XP SP2; using Firewire; Itunes 6; Ipod Updater 2005-09-23.
Several months ago, after reading thousands of posts and trying every possible suggested fix, I found one that had you go to Microsoft and do a patch of some sort on IEEE 1394. After doing this, IPOD synched immediately. No more problems, until subsequent updates from MS were installed. Now, can't do anything again.
Does anybody know where that patch is, or what it was about? I can't seem to find the post again...
Any know anything about that??

Clay,
This driver has been released for some time. If you want you may download it and have a try. I have not tried it myself. I am using an Adaptec Fireconnect 8300 in Windows XP SP2 and it is working great for me without the need for additional drivers.

No "IEEE 1394 Bus host controllers" node in device manager

I have a new computer running Windows 7. It is functioning well, apart from the firewire card not being recognized. I can see that the BIOS does see the firewire card. Pages on the web offering advice on this kind of problems start their solutions with going
to the device manager and expanding the "IEEE 1394 Bus host controllers" node in the device tree. Only I don't have such a node. How can I get the "IEEE 1394 Bus host controllers" node to appear in the device manager?
Windows update reports that Windows is up to date.

This is one of many threads I came across googling roughly 'IEEE 1394 device not showing up in device manager'. After a lot of reading I never found a real solution - until I started piecing some things together. This is what I did and it works, seems very
simple, logical. Thought I should share it, hopefully save someone else the agony of searching and reading for hours.
Basically, what I think is or can be happening -- and I'm no expert at all -- is that there's miscommunication between the OS, the bus, and the device. The OS doesn't install the service for the bus unless the device is plugged in at startup (the external
hard drive, camera, or whatever), and sometimes it doesn't install the service even if the device is plugged in. Perhaps the device is supposed to send a message that starts the service - who knows. Maybe on older devices the driver isn't doing what it's supposed
to do, and perhaps you have no updated driver and can't get one.
In any event, I edited an entry in the registry that tells the 1394 bus host controller to start at OS startup instead of 'on demand'. After a restart, the bus host will load at startup, and when you plug your firewire device in, the bus host will detect
it and run normally... At least it works for me. Here's the instructions:
Go to search, regedit.exe, run program. This opens the registry.
Go to HKEY_LOCAL_MACHINE\SYSTEM\CurentControlSet\Services and find the folder that corresponds to the 1394 bus host you normally use or see in device manager. On my computer it's 1394ohci. You might have to do a little digging here to make sure you've got
the right service. There's actually 2 folders/entries in my registry that look similar. I used this one and it's working for me.
When I click on the 1394ohci folder it brings up a list of settings. For "Start," "REG_DWORD," the 'Data' value is probably going to be 0x00000003. That means 'start on demand'. I changed this to 2, which means 'start at startup'. To
modify value, right click on start, select modify, and type in 2. Here's a link to descriptions of this stuff: http://technet.microsoft.com/en-us/library/cc722564.aspx
That's it. Close the editor, restart, and the IEEE 1394 Bust Host controller\1394 OHCI Compliant Host Controller should show up in device manager. And when you plug-in your device, it should be detected. Depending on what driver you're using for the bus
host controller, you might see an extra entry popup in device manager (if you're using the 'legacy' driver). Otherwise nothing else pops up when you plug in your device. I guess it might depend on the device though. That's the way it is for me with an older
Acom external hard drive...
Hope this helps...

W520 IEEE 1394 device missing

W520 4270-CTO
W7 Pro
The IEEE 1394 device is now completely missing from device manager. It seems like hardware failure but I thought I would post here to see if anyone has any suggestions. BIOS reset and factory restore did not resolve the matter.
I have contacted a local service depot so the machine will go in for warranty service next week (after labour day weekend) if not resolved beforehand.
Ted
Solved!
Go to Solution.

Problem sorted out.
The IEEE 1394 drive by Ricoh will shut down the port and the card reader (both Ricoh) when nothing is connected to either. Inserting a memory card or connecting a firewire device will wakeup both the IEEE 1394 port and the card reader.
Ted

Itunes/Iphone/Ipod device driver issues - tried everything. Still not working.

After hours and hours of research, I'm completely stuck. Here's the basic problem.
When I plug in my Iphone to my laptop, windows pulls up a little window that says installing device driver software. After several minutes, the process fails and a message comes up that says windows found drivers for my device, but encountered an error and wasn't able to install them. In the device manager, the iphone is listed as an "other device" with a yellow triangle/exclamation point. Itunes never recognizes the device.
When I plug in my ipod nano 4th generation, the exact same thing happens, except it's listed in the device manager as an ipod. (same yellow triangle though.)
Up until today, both of these devices have been working properly, syncing without trouble. The iphone synced wirelessly and the ipod every time I plugged it in. I can't figure out what on earth happened to my laptop today that messed things up.
It's also worth noting that I have another older ipod nano... second generation, I think, that plugs in and is recognized immediately, works perfectly.
Here is what I've done so far:
1. I worked through every single troubleshooting guide that Apple has to offer. No change.
2. I did a complete clean install of itunes and all additional components, rebooted and reinstalled. No change.
3. I uninstalled/re-installed usb controllers in the device manager. No change.
4. reset both the phone and the ipod. No change.
5. I've tried various cables. No change.
6. I've run system checks and repair utilities for windows vista.
7. I've used selective start up to see if another program is interfering. I've stood on my head and counted to one hundred. I've only said seventeen swear words.
At this point I've done so much searching and troubleshooting, I can't imagine how anything is going to fix this issue. So this is my last hope. Please oh please be smart enough to tell me what to do...

Not sure if this is significant, but in a weird turn of events, when I tried plugging the ipod in this morning, the little message that pops up to install device driver software actually told me the drivers were installed successfully. However, in the device manager, it still says the drivers are NOT installed properly, the little yellow triangle is still there and the ipod still isn't registering in itunes, or my computer. So. Not really any improvement, but a different symptom none the less?
I'm desperate, guys. Someone help?

Windows vista, Ipod shuffle 4th gen. Computer cannot find device driver software for ipod.

After several hours trying the troubleshooting options provided by the apple support site, I have come to what I think is the issue here. My girlfriend recently got an ipod shuffle and when plugging it into her computer the dialog pops up saying it is installing device driver software for the ipod. Eventually it asks me to insert the CD that came with the ipod. No CD came with the ipod, so I click the option that says "I do not have my cd". Then it gives me the option of searching automatically or manually for the driver software. The automatic way can't find it. Doing it manually, with the help of the troubleshooting page, didn't work either. google search can't seem to help me on this one. Also, I tried plugging the ipod into my computer (not hers) and it worked fine, it was able to install the device driver software on its own. Does anybody know the issue here? My computer has windows 7, and hers has vista. Hers is Serice Pack 1. When I tried installing service pack 2 it wouldnt work. I don't know if that is the issue though. I have tried just about everything, I think the issue is finding the device driver software. When I do a google search nothing comes up, so I have no idea what to do at this point. Any help would be appreciated, thanks.

Well its surprising to know that! But even have an ipod shuffle 3rd gen n dint face any problem like that. FYI no cd comes with the ipod jus take ur ipod to an apple exoert n he will solve ur problem .

IPod not recognized by itunes, driver device won't install?

I've been at this for hours and I'm becoming rather frustrated. I've been using my 4g ipod touch since christmas and it's worked fine. I plug it into my new laptop, and it tells me that the device driver needs installed. I let it install, yet it's still not recognized. I go through the device manager and attempt to update the software, and every time it tells me that there is some kind of error and the update cannot be made. I've tried everything under the troubleshooting methods. Does anybody have any clue what is causing this? Any help is greatly appreciated.

Here is a tutorial for how to fix your usb not recognized,
_*NOTE: Be sure that all of the usb ports are unplugged ;)*_
Tutorial:
1)a)Go to home button, and search regedit
1)b)And go to HKEYLOCALMACHINE/SYSTEM/CurrentControlSet/Services/Usbstor click it.
1)c)- In the usbstor there is a file named ErrorControl and double click it. And it says value 1 change it to 3 and save it.
2)a)Go to Windows/System32/DriverStore/FileRepository/ And click the file named
usbstor.infx86_neutral83027f5d5b2468d3 and double click it, and copy the files named usbstor and usbstor.pnf
2)b) Go to C:Windows/inf and paste the files you have copyed.
2)c) Reboot your computer and your usb cable works again
Message was edited by: Altdorf

VISTA - can;t find device driver for your IPOD - read the solution here!

It would appear that VISTA is rather stupid when it comes to the Ipod - it can't find the driver for itself. Do the normal autmatic way of trying to find the driver (that doesn't find the device) then look in the hardware device list (control panel) you should see you Ipod listed under other devices with a yellow triangle next to it. Right click this line and select "properties". then click "update device driver". Then, DON'T do the automatic find, instead click "I will choose the device from a list". Click on "storage device" and voila! VISTA now finds a USB mass storage device and installs it - JOB DONE! HOORAY!
good luck!
Mark.
Ipod 5G video colour Other OS WINDOWS VISTA ULTIMATE

When you are prompted to look for a driver input
C:\WINDOWS\System32 and browse it will find a generic
volume that fixes it.
I tried this as well. I can find a Generic Volume (I think it lists SD, MMC- neither of which seem correct), but neither of those helps. iPod still isn't recognized as a drive even in disc mode. I started another thread after not finding this one. I'm not sure why USB Mass Storage device isn't one of the options.

Apple iPod USB Device driver issue on Win XP - syncing shuffle 2nd gen.

Hello fellow iPod shuffle users. Any of you run into this problem using the following configurations? Any advise/recommendations/workarounds much appreciated as I've burned 3 days on this issue and I'm still stonewalled.
I personally think it's a device driver issue/bug and am searching for a way to update my Apple iPod USB device driver for Win XP. Two brand new ipod shuffles (received for Christmas 2008) are both behaving this way, so the problem most likely points to a global software issue more-so than to shuffle hardware issue.
PROBLEM STATEMENT: Driver data i/o streaming issue does not allow shuffle to sync data with iTunes after initial sync (i.e. reading the content of the shuffle is good, but writing modified content fails). Posted error message "The ipod ... cannot be synced. Required disk cannot be found". After cracking the hood on my device driver, the problem seems to point to the Apple iPod USB device driver for Win XP. Driver will recognize the shuffle and read to it, but subsequent write attempts will result in device driver balks that "this device cannot start (code 10)".
ATTEMPTED WORKAROUNDS:
*Read All "How to Get Started Manuals" to make sure I was using the right technique for syncing my two shuffles from within iTunes... tried and failed
*Ensure only one shuffle was plugged in at a time (saw notice that two shuffles plugged in at the same time is not yet a supported config)... tried and failed
*The 5 R's as recommended by Apple Support... tried and failed.
*I've tried all 3 built in USB ports on my Lenovo T60. no love... tried and failed.
*Per discussion board: From Window's Device Manager-> Scaned for new hardware while shuffle was syncing...tried and failed.
* Per Discussion board: From Window's Disk Management -> Ensured shuffle came up as a FAT32 filesystem... connection tore down as quickly as windows recognized it.... tried and failed.
*From Windows Software config utility: Ran repair to re-install itunes 8... same results.
*From Windows software management utility: Uninstalled and reinstalled itunes 8... same results.
Hardware: IBM Thinkpad/Lenovo T60. Using build in k/b & no external mouse. Has 3 USB built in ports.
Software: Windows XP Pro SP2/iTunes 8.0.2/shuffle (2nd gen) driver 1.0.4 (same behavior using the original driver 1.0.3).
Apple iPod USB Device properties:
Driver Provider - Microsoft
Driver Date - 7/1/2001
Driver Version - 5.1.2535.0
Digital Signer - Microsoft Windows Publisher

Hi. Ive got pretty much the same problem.... Got a new shuffle for christmas..having real problems syncing with itunes. Funnily enough I managed to get 25 tracks on it but then it just stopped. error message says " The ipod shuffle cannot be synced. The required disk cannot be found." Ive done restore, and downloaded a reset utility thingy to try but still no joy.

IPod IEEE 1394 SBP2 Device Driver

Similar Messages

Maybe you are looking for