IPod in Recovery Mode Loop, Restore Does Not Work

When I turn my iPod on it says "Connect to your computer. Use iTunes to restore." I connect it to iTunes, restore it and then it says that it is still in recovery mode and needs to be restored.
Nothing I've tried has worked. I've put it in disk mode, I've changed the drive letter so Windows doesn't confuse it with anything else. I tried to go to the Genius bar but they were so backed up the only appointment I could get was for 8pm tomorrow!
Hopefully someone can help!

I've got the same problem with my iPod nano 3rd generation. I'll connect it to iTunes, and it says that an iPod has been detected in recovery mode, and it'll ask me to keep it connected to the computer. It'll then prepare it for recovery, and then tell me there's been an iPod detected in recovery mode. It'll perform this loop several times before I'm given the option to restore it, in which the iPod displays an old version of the iPod interface (I'm talking 1st or 2nd generation of the classic iPod).
Once I'm given the option to restore, it says "Extracting software", finishes, and says that the iPod is being restarted, and then starts with the "iTunes needs to prepare your iPod for recovery. Please leave your iPod connected." loop once again.
I would really prefer to not have to drive to the Apple store to get this problem fixed...

Similar Messages

  • HT201412 Hi, I have an iPhone 5S went into recovery mode and Restore does not clear up the problem, how to solve?

    Hi, I have an iphone 5s went into recovery mode and reset does not clear up the problem, How to slove?

    imansoheili wrote:
    Hi, I have an iphone 5s went into recovery mode ...
    Once the Device is asking to be Restored with iTunes... it is too late to save anything...
    See Here  >  http://support.apple.com/kb/HT1808
    You may need to try this More than Once...  Be sure to Follow ALL the Steps...
    After you have Recovered your Device...
    Re-Sync your Content or Restore from the most recent Backup...
    Restore from Backup  >  http://support.apple.com/kb/ht1766

  • Hello, all of a sudden I fell down my system and completely erased all bookmarks. Your progress with restoration does not work, send me ansver,please

    Hello, all of a sudden I fell down my system and completely erased all bookmarks. Your progress with restoration does not work, write me of bookmarks could not be loaded. Please advice on everything because I came and they seriously need it.

    Did your computer crash or did Firefox crash causing the loss of the bookmarks?
    You can check for problems with the places.sqlite database file in the Firefox Profile Folder.
    *http://kb.mozillazine.org/Bookmarks_history_and_toolbar_buttons_not_working_-_Firefox
    *https://support.mozilla.org/kb/Bookmarks+not+saved#w_fix-the-bookmarks-file
    See also:
    *http://kb.mozillazine.org/Lost_bookmarks
    *http://kb.mozillazine.org/Firefox_crashes
    *https://support.mozilla.org/kb/Firefox+crashes

  • I have an iPod and an Ipad and want to use FaceTime calling from the iPod to the Ipad but it does not work. I use the same iCloud acount.

    I have an iPod and an Ipad and want to use FaceTime calling from the iPod to the Ipad but it does not work. I use the same iCloud accountedge

    Did you set up different email addresses for each device?
    iOS: Using FaceTime
    The Complete Guide to FaceTime: Set-up, Use, and Troubleshooting Problems

  • IPod is stuck in recovery mode and retoring does not fix - What can?

    I've installed a new computer and transfered itunes just fine but when I connected my sons iPod it stated "itunes has detected an iPod in recovery mode. You must restore this iPod before it can be used with iTunes." I've now restored it more times than I care to remember (it appears restored back to factory settings) but the same message ".... detected an iPod in recovery mode. You must restore..." persists and thus will not download music library. What else can be done?
    Dell precision 390   Windows XP  

    This repetitive "ipod found in recovery mode" message is most likely caused by drive letter confusion on your computer.
    In that case, you'll need to try assigning your iPod a different drive letter.
    Log off of any other users on your computer.
    Then, put your iPod into Disk Mode and see these steps:
    1 - Don't plug in your iPod yet.
    2 - Go to "START -> Control Panel -> Admin Tools (if you don't see this, click on "classic view" button on the left panel) -> Computer Management."
    3 - Click on the "Disk Management" button in the left panel area.
    4 - Now, with "Computer Management" and Control Panel windows opened, connect your iPod to the computer.
    5 - Right-click on your iPod's listing there (after a few moments when it gets recognized in this drive window), and click on "Change Drive letter and Paths". Then the "Change..." button.
    Here's what it should look like:
    Assign your iPod the letter "M" "N", "O" or the like (further along in the alphabet).
    For more details, see this Support article:
    Windows confuses iPod with network drive or hard drive and may keep iPod from mounting
    I hope that helps you.
    -Kylene

  • 'iTunes has detected an iPod in recovery mode' loop. Help?

    On Friday I plugged in my iPod touch (4g) to download the new ios 5 (from 4.3.5), but about when it reached about 4 minutes remaining, the error message 'iTunes has detected an iPod in recovery mode. You must restore the iPod before using it with iTunes.' appeared. I've tried restoring it about 10 times now, the closest being  just 2 seconds away from finishing.
    The iPod has the screen on the usb pointing to the iTunes symbol.
    It does NOT show up under computer, or under disk management, so I don't know if i can change the drive letter. If there are alternatives, please let me know!
    I've tried using another computer and different users - all of which comes up with the same error, so I'm thinking that it is the iPod that is the issue.
    When i attempt to restore it it says it should take around 15 minutes, but usually the error comes up within the last 5 minutes.
    The iPod info just says Name: iPod
                                      Capacity: n/a
                                      Software version: n/a
                                      Serial number: n/a
    Really don't know what to do, any help is appreciated.

    Unfortunately not yet. Any thoughts on this are useful...

  • "I Tunes has Detected an iPod in Recovery Mode".  Restored it BUT.......

    Been using my iPod and I bring it to work to copy over a book on CD. It hasn't been hooked up to my computer at work in a few weeks but works well at home. It plays the music I HAD on it but when I pluged it in on my work computer I get the "I Tunes has Detected an iPod in Recovery Mode" message and it says it needs to recovery it to work.
    In the Summary page in iTunes I see that my iPod is up to date but my iPod has lost its name and it says I need to recover it. I ran the recovery, it downloaded what it needed, installed on my iPod and it restarted. Now I get the "I Tunes has Detected an iPod in Recovery Mode" again and again it asks to recover.
    Is this an endless loop I am stuck in? Does my iPod some how need a complete reboot/wipe/format?

    Been using my iPod and I bring it to work to copy over a book on CD. It hasn't been hooked up to my computer at work in a few weeks but works well at home. It plays the music I HAD on it but when I pluged it in on my work computer I get the "I Tunes has Detected an iPod in Recovery Mode" message and it says it needs to recovery it to work.
    under the circumstances you describe, it seems most likely that the relentless recovery mode message on the work PC is being caused by a Windows drive letter confusion on the work PC.
    for more information on troubleshooting that possibilitity, see:
    "iTunes has detected an iPod in recovery mode - Use iTunes to restore"
    ... and:
    Windows confuses iPod with network drive or hard drive and may keep iPod from mounting or songs may seem to disappear

  • IPod stuck in recovery mode with home button not working

    Hi, I was restoring my iPod and everything went fine until it was restarting with the apple logo and loading symbol. My iPod's home button hasn't been working in a while so I use assistive touch. Now the iPod is stuck in recovery mode and I can't press the home button, I don't know what to do. Pls help!

    Try:                                               
    - iOS: Not responding or does not turn on           
    Whenit says place the iPod in recoivery mode:
    Place the iPod in recovery mode using one of these programs:
    For PC
    RecBoot: Easy Way to Put iPhone into Recovery Mode
    or
    http://joshuabailey1997.wordpress.com/2010/09/02/recboot-v1-3/
    If necessary:
    Download QTMLClient.dll & iTunesMobileDevice.dll for RecBoot
    and                                           
    RecBoot tip
    RecBoot may have problems on 64X windows, then try:       
    Tenorshare ReiBoot – Enter & Exit iPhone, iPad, iPod Recovery Mode with a Single Click
    For MAC or PC       
    The Firmware Umbrella - TinyUmbrella
    Installs blootware on PC too
    - If not successful and you can't fully turn the iOS device fully off, let the battery fully drain. After charging for an least an hour try the above again.
    - Try another cable       
    - Try on another computer                                                       
    - If still not successful that usually indicates a hardware problem and an appointment at the Genius Bar of an Apple store is in order.
    Apple Retail Store - Genius Bar                                     

  • ITunes has detected an iPod in recovery mode loop

    Hello,
    I have an Ipod 5 and during update of the OS to the latest, the process got an error.
    No my Ipod is in recovery mode. Everytime I download the Update (Restore and update) there is this constant pop up that comes up (iTunes has detected an iPod in recovery mode).
    I click ok everytime but then after 5h download there is the Processing file part which when I click ok on the pop that constantly keeps coming after some it, all stops and I need to restart the process again for 5h. Keeps going on like that.
    Its really annoying stuck in an update like that which only a minor patch. I can't use my ipod for days now.
    Could you please help.
    Thanks
    Jérémie

    Maybe:
    Restore loop (being prompted to restore again after a restore successfully completes)
    Troubleshoot your USB connection. If the issue persists, out-of-date or incorrectly configured third-party security software may be causing this issue. Please follow Troubleshooting security software issues. .
    Next try placing in DFU mode and then restoring.
    How to put iPod touch / iPhone into DFU mode « Karthik's scribblings
    Then try restoring on another computer.
    Last, make an appointment at the Genius Bar of an Apple store.
    Apple Retail Store - Genius Bar

  • Ipod Touch Recovery Mode Loop - Error Code 14

    I attempted to update my Ipod Touch (3rd Gen 32 GB) to the latest firmware (IOS 5 i think). It froze during the process and has since been stuck in a Recovery Mode loop. I have followed all recommendations on their website, called Apple support and re-installed all Apple related software, and even been to the Genius Bar in our local Apple shop, and it still broken!! They said that as it was out of Warranty (six months) and had a 'Hardware fault' i could buy a replacement for £120. I tried to argue with the shop staff and higher level customer support staff on the phone that my Ipod was working just fine before attempting to update the firmware so how could it be a hardware fault??
    Is it just me or the fact that as soon as the one year warranty is up, Apple expect you to replace your faulty item with a new one. So much for good quality goods, can we expect Apple products to last just over a year and then be expected to buy a replacement!!
    Isn't the fact that i have been offered a new Ipod Touch 32GB for only £120 pounds an admission that the product has some fault issues??
    Anyone else in this position?
    Any ideas how to fix the problem?
    Anyone else disappointed with Apple Customer Support?

    From the article cited at the end of my post:
    Error 6: All of the steps in this article apply to resolve this issue. Following iTunes for Windows: Troubleshooting security software frequently resolves this error. There may be third-party software installed that modifies your default packet size in Windows by inserting a TcpWindowSize entry into your Registry. If your default packet size is set incorrectly it can cause this error. Contact the manufacturer of the software that installed the packet size modification for assistance.
    http://support.apple.com/kb/TS1275

  • Ipod shut off and home button does not work

    So my friends iPod shut off and her home button doesn't work, and if plugged in wont turn on either? We tried the alcohol method but it did not work, anyone have any suggestions on what to do. ( her warranty is also expired)

    Try:                                               
    - iOS: Not responding or does not turn on           
    Ignore the reset and when it says place the iPod in recovery mode
    Place the iPod in recovery mode using one of these programs:
    For PC      
    RecBoot: Easy Way to Put iPhone into Recovery Mode
    or
    http://joshuabailey1997.wordpress.com/2010/09/02/recboot-v1-3/
    If necessary:
    Download QTMLClient.dll & iTunesMobileDevice.dll for RecBoot
    and                                          
    RecBoot tip
    RecBoot may have problems on 64X windows, then try:       
    Tenorshare ReiBoot – Enter & Exit iPhone, iPad, iPod Recovery Mode with a Single Click
    For MAC or PC       
    The Firmware Umbrella - TinyUmbrella
    Installs blootware on PC too
    - If not successful and you can't fully turn the iOS device fully off, let the battery fully drain. After charging for an least an hour try the above again.
    - Try another cable              
    - Try on another computer                                                       
    - If still not successful that usually indicates a hardware problem and an appointment at the Genius Bar of an Apple store is in order.
    Apple Retail Store - Genius Bar                                     

  • XP windows restore does not work yet all is set correctly

    XP windows restore function does not work. All the restore points exist with descriptions of the changes that prompted them. It will let me select them (restore points) and restore process will strart but after rebooting it will ultimatly let me know that it could not restore.
    Does the Lenovo Restore and Rescue utility disable this function of XP ? ?
    Thanks

    Well I have a 6460-8WU that came with Vista and I got the downgrade CD set and tried to restore to XP.  The first time it said it failed to restore my system, but it seem to have XP and all the applications that I expected to see.  Later I had a problem with the Welcome Windows screen being unavailable... used only the Classic Windows Logon, I called Microsoft and they suggested using their system restore.... which didn't work at all... I tried 5 or 6 different backup files from different days and none of them worked.  At that point I decided to use the Lenovo downgrade CDs and format the hard drive restoring everything from scratch. It took me a few tries but eventually I did get it to say that it had successfully restored my system.  The items I learned from like 4 failed attempts to restore it are this:
    1.  Don't try to restore it while in the advanced dock.
    2.  When the restore process says to remove Disk # x and press OK, remove Disk # x-1 (the currently inserted Disk, and insert Disk # x, and then do not press OK until you wait 20 or 30 seconds or until the little icon of a CD that flashes when Windows reads a newly inserted disk has finished.  When I tried clicking OK either before I had actually inserted the next CD or too soon after I had inserted the next CD the process went downhill from there and failed to restore properly.
    3.  When it seemingly has read all the CD's and says it will now start the restoration process, but you are asked to press Next... well firstly there *is* no Next button to press and the other buttons other than Cancel are greyed out.  The solution there is to wait, and wait, and wait... so long that you may think the process has failed and the computer is hung... but it is not.  Eventually it will continue from that point.
    Aside from that, I notice that there is a new version of the Recovery Application on the Support site, but
    if you install the latest Rescue and Recovery 4.20.0511.00 in the readme there are 31 "considerations" listed, which are basically conditions under which it does not work properly or as expected, so I won't be trusting it to recover my system.  I will make a Paragon Drive Manager image after I get the updates all installed and use that to restore from.

  • Linking Keynote on iPod-Touch with Keynote on MacBookPro does not work.

    I purchased Keynote 5.0.5(942) for my MacBookPro (MacOS 10.6.7), and
    KeynoteRemote 1.2 (53) for my iPod-Touch 4th generation.
    I am trying to link KeynoteRemote on the iPodTouch with Keynote on MacBook Pro.
    KeynoteRemote gives me a Passcode, which I enter in the preferences panel on Keynote for MacBookPro.
    Verification does not work. Nothing happens, and after sometime an error message appears that
    verification has failed.
    I have tried to do all combinations of setting the firewall on or off, and checked out all linkage and network settings.
    Does anybody know what the tricks are to get KeynoteRemote to work with Keynote on MacBookPro?
    Or does KeynotePro not work at all?

    thanks, David. it works now. I think the problem was the firewall. I fixed it now.

  • "FOR REC IN CURSOR(PARAMETERS) LOOP" command does not work. Why?

    Hi to all.
    It's a pleasure to receive your help.
    In "FOR REC IN CURSOR(PARAMETERS) LOOP" command although the query return value does not enter the loop.
    Sounds simple, but I'm not seeing the flaw...
    Suggestions?
    Version: Oracle Database 10g Enterprise Edition Release 10.2.0.4.0
    Thank in advance,
    Filippe

    Filippe Soares Roza wrote:
    Hi to all.
    It's a pleasure to receive your help.
    In "FOR REC IN CURSOR(PARAMETERS) LOOP" command although the query return value does not enter the loop.
    Sounds simple, but I'm not seeing the flaw...
    Suggestions?
    Version: Oracle Database 10g Enterprise Edition Release 10.2.0.4.0
    Thank in advance,
    Filippe
    see a picture of my car that does not work.
    Tell me how to make my car go.
    How do I ask a question on the forums?
    SQL and PL/SQL FAQ

  • I cannot get my ipod to unlock, the touch screen does not work and I cant reset it

    I cannot get my ipod to unlock, the touch screen will not work and everytime i try to reset it I take a picture.  any suggestions

    Try:
    - Reset the iOS device. Nothing will be lost
    Reset iOS device: Hold down the On/Off button and the Home button at the same time for at
    least ten seconds, until the Apple logo appears.
    - Restore from backup. See:
    iOS: How to back up
    - Restore to factory settings/new iOS device.
    -  Make an appointment at the Genius Bar of an Apple store.
    Apple Retail Store - Genius Bar

Maybe you are looking for

  • BT Home Hub 5 problem

    I recently got infinity 2 installed in my home on 21/3 and was told that i was able to get 51Mbps. Everything was fine over the weekend always slightly under the speed i was told, until 24/3 where i noticed that it was going a bit slow. I done a spee

  • How can I use the appletviewer

    I am programming on a solaris network at school and I can't get the appletviewer to work. I am using the emacs editor and the javac compiler from my account. Whenever I try and run the appletviewer I get this error: nova> appletviewer index.html Exce

  • Calling a SQL script from the PL/SQL block.

    Hello All, I am using oracle 11g database. My requirment is as follows. I have a SQL script to alter the table. But before alter the table I need to test some condition , if the condition satisfy then I have to alter the table through the SQL script.

  • Can 10.4 included with my new computer be installed on my old?

    Hi, I just bought a new iMac 20" about a week ago. Along with that, I have my Powerbook 12" which I owned previous to this purchase. I have installation disks with my new iMac and want to know if I can install the OS on my Powerbook so they're both o

  • AFX wont load on Mac OSX 10.9.2

    Ok - I'm on the new black trash can - 3.5 ghz - 6 core intel xeon E5 Premiere opens and runs no proeblems, but AFX wont open an gives the warning - you cant use this verision of AFX 0S 6 on this version of OSX Is there any easy way to fix without goi