Ipod Nano 4g Wont Turn On After Unplug

My ipod nano 4g is working fine when its plugged in.. itunes also can see it.. but as soon i unplug it, it turns black the screen and i cant turn it on.. only if i plug it again.. i tried to reset and erase everything but nothing work??
anyone know what to do?

Ok, so my ipod nano 4th generation will not power on. Once I plug it in the apple icon comes up on the screen and then it syncs to itunes. As soon as I eject it from the computer it powers off and all i get is a black screen and nothing else. It will not power on at all? Also I have tried to reset the unit on itunes and through the unit. Please any help would be greatly appreciated.
Message was edited by: suzukigunner25

Similar Messages

  • 7th gen iPod nano won't turn on after disconnect.

    7th gen iPod nano won't turn on after disconnect. I loaded some new music, synced and ejected correctly. screen went black on unplug. Waited, did the button trick, didn't work. plugged it back in & it is recognized immediately. restored, resynced & ejected again. same thing-black screen w/ no response. Charged it overnight. ejected, screen then went to language setting. OK for English, eject & back to black on unplug. Switched ports for cable, tried eject thru PC...all resulting in dead nano after unplug. I really don't want to charge into the store & take it out on the poor kid who will catch the brunt of my frustration. anyone have a suggestion?

    Hello Marie,
    I would be concerned too if my iPod nano was not powering on.  I found an article for the 6th generation iPod nano that has steps you can take for an issue like this (the only difference for the 7th generation iPod nano is the steps you will take for the reset. I included the steps to reset a 7th generation iPod nano below):
    Will not turn on or screen remains dark
    Connect iPod to power for at least ten minutes to ensure that the battery has enough charge to allow iPod to turn on.
    If iPod does not turn on after ten minutes, try resetting the device while it is still connected to power. Reset the iPod by holding down the Sleep/Wake button and the Volume Down button for at least eight seconds or until you see the Apple logo appear.
    If the Apple logo appears on the display, connect iPod to a computer and verify that it appears in iTunes and can play music. If iPod appears in iTunes and can play music, no further troubleshooting is needed.
    If the screen remains dark and will not turn on, then your iPod may need service.
    You can find the full article here:
    iPod nano (6th generation): Hardware troubleshooting
    http://support.apple.com/kb/ts3474
    All the steps apply to the 7th generation except the steps for the reset.  To reset a 7th generation iPod nano, use these steps:
    Press and hold the Sleep/Wake button and the Home button for six seconds, or until the screen goes dark. The Apple logo appears after a few seconds, and then the Home screen. You may need to repeat this step.
    I got these steps from this tutorial, which may also help with your iPod not appearing in iTunes:
    iPod nano not appearing in iTunes
    http://www.apple.com/support/ipodnano/assistant/itunes/
    Thank you for using Apple Support Communities.
    Best,
    Sheila M.

  • My ipod touch 2gn wont turn on after being charged in a ipod dock...it's been 3 weeks now and i've tried everything and noting has worked! Apple, you better expect paying for this because i am not wasting my money again!

    my ipod touch 2gn wont turn on after being charged in a ipod dock...it's been 3 weeks now and i've tried everything and noting has worked! Apple, you better expect paying for this because i am not wasting my money again!

    Have you tried a reset?
    Stedman

  • Help! Ipod nano won't turn on after disconnecting!

    Okay I've had my Ipod nano for like 3 weeks. I've used it once. It worked fine when I first got it and after my battery ran out I haven't used it for about a week. When I got it back I hooked it up to my computer and updated the stuff on it as well as let it charge. After is says to safely disconnect, I disconnect it but it automatically turns off and won't turn back on. I've tried resetting it and nothing works. I thought the battery was dead but I've left it plugged in (not only USB on my computer but also tried an outlet) and it never completely charged. I've even left it plugged in overnight (well over the 4 hours it's supposed to charge). I have no idea what to do (It also took like at least a full day to completely charge the first time I've had it)

    Tuesday, December 02, 2008 7:23:56 PM
    Okay my iPod wouldn't turn on . (Guess I will be throwing out the box to ship my ipod for warranty replacement)
    at like 11pm dec 1 2008, the ipod was dead, pressing the power button did nothing.
    I thought it was a goner... I even ordered a warranty replacement..
    ipod wouldnt turn on . left it for 24 hours. when I got home from school the next day
    it tried to sync but my playlist did not exist..it even showed the folder in windows
    After trying various USB ports and seeing an Apple Icon, and "connect to power low battery"
    I even requested a warranty replacement... and apparently you throw out the box they send to cancel. I wish I could be courteous and let them know
    So in short
    PROBLEM;
    ==IPOD Won't Power on when you press the power button==
    (FIRST OF ALL , I STRONGLY URGE YOU TO NOT TRY TO OPEN THE IPOD UP,
    you will probably scratch or damage the beautiful iPod .. when it will be perfectly fine 24 hours later...)
    Try:
    RESET, and plug in to itunes and restore..
    SOLUTION:
    http://www.everymac.com/systems/apple/consumerelectronics/ipodfaq/ipod-troubleshooting-wont-turn-on-appear-hung-sad.html
    Official Apple Documentation:
    http://support.apple.com/kb/TS1383?viewlocale=en_US
    I guess my actual story will make you believe that THIS SOLUTION actually works.
    "Let the iPod battery drain
    In rare cases, iPod might get into a state in which it needs to be drained completely before it can be reset. If iPod didn't turn on after you reset it, follow these steps:
    1. Disconnect iPod from all power sources and leave it disconnected for about 24 hours.
    2. Reconnect iPod to the Apple iPod Power Adapter or computer and reset it.
    I even tried the iPod on 2 computers and it was sort of detecting the serial # in Windows
    but mostly freezing up windows.
    4. " Let iPod's battery drain"
    Was the solution for my iPod 3rd generation.
    So now that the problem was fixed, I guess iPod is so terrible after all
    Just don't drop your iPod get it a nice case
    it took from 9pm December 2,2008 to about Dcember 2,2008 6:45pm
    roughly 20 hours.. so this morning when I left I pressed the button and it wouldn't turn on
    I thought maybe the battery was knocked loose but the battery was just so low or something
    To prevent this problem I guess whenever you ipod is low battery, charge it before it gets dangerously low
    As sad as it is to wait like 24 hours without your iPod just to pray that the problem is the battery or something and then it will power on..
    When it actually does power on you would see the apple Icon
    == When it was all said and done==
    I didn't really need to use "restore" option, i think itunes resynced what it needed.
    And thanks to this I upgraded to Itunes 8 .. which I was too lazy to do before
    ==STILL DOESNT WORK?==
    If you bought it less than a year ago... Warranty..
    https://selfsolve.apple.com/GetWarranty.do
    Enter your Serial# and country and it will be located at the back of your iPod under where it says 8GB or whatever (at least for iPod Nano 3rd generation)
    I always like posting solutions, so that someone like me can benefit from it.
    It is my understanding that if you do send in your iPod they don't care about the USB cord or headphones that came with it, so you just ship the iPod itself
    see here for some frequently asked questions.
    http://www.apple.com/support/ipod/service/faq/

  • Ipod nano 4g wont turn on

    I have an ipod nano 4th generation, was never used and sat in a box for years but i started using it as my iphone broke. Last night i went to sleep and it was working fine but when i woke up it was turned off and it wont restart and i have restored it coutless times, i've hend select and menu and toggled hold off and on, and eventually when the apple logo appears if i press anything on the wheel it shuts back off again like if i press the middle button the apple logo vanishes and nothing else happens. Anyone know whats going on?

    Hello KyleMack1993,
    You might try putting the iPod in disk mode before trying to restore.
    Putting iPod into Disk Mode
    http://support.apple.com/kb/HT1363
    Cheers,
    Allen

  • My ipod nano 6th generation turns off after she tells me the screen is dimming than ipod goes off.

    I wanted to know if there is someone at Apple that can give me some guidance on how to use my ipod nano 6th generation.  I am not sure if I am working it properly or if there is something wrong with it.
    I cannot get back to home page; I shut it off and on and it just stays on same page.  I cannot take the voice constantly interrupting the song or functions;
    When you set an album in play it will just play the first song over and over never going to next song.  The genius interrupts and starts randomly playing different songs; when you select a song the voice comes and and tells you the screen is dimming and then seconds later it turns off.
    I have tried to read the directions put the ipod won't allow me to follow.
    Please help!

    Is VoiceOver turned on?  See here for more help on how to turn it off if need be.
    http://support.apple.com/kb/HT4317
    B-rock

  • Ipod nano chromatic wont turn on

    ipod is recognized by itunes and plays while connected. Battery shows as fully charged. Once disconnected ipod turns off and will not turn back on. Have tried restoring with no luck. Please help.

    Welcome to the Forums!
    You could try:
    Hold down the Menu and Center buttons on the iPod until the screen changes.
    Connect to iTunes. Select it in the Source List on the left. Go to the Summary tab. Click Restore. NOTE: You will lose all settings and have to re-transfer music.
    Good luck!
    -Nate

  • After restoring ipod nano it wont sync with itunes. states error 13019 occured

    after restoring ipod nano it wont sync with itunes. states error 13019 occured

    I seem to recall that another user has this problem and found that it was because of some corrupted music files they were trying to sync over.
    Try syncing smaller bunches of tracks till you come upon the ones that cause the error. You should be able to find out which ones are causing the trouble this way.
    The other user said they used something called MP3Diags. I cannot vouch for this software at all, I have never used it.
    I did a quick search on "how to repair MP3 files on Mac" and also found this:
    http://triq.net/articles/mp3-validator-mac-os-x
    i

  • The screen on my ipod nano 2nd generation turns black. It still plays music. I've tried resetting the ipod to clear the black screen and the screen goes back to it's normal state but after a few minutes the screen goes black again.

    The screen on my ipod nano, 2nd generation, turns black. It stills plays music. I've tried resetting the ipod to clear the black and the screen goes back to it's original state. But after a few minutes the screen turns black again, while the music is still playing. What can I do about this?

    That's just the iPod's backlight timer going off, signaling the iPod's backlight to turn off to conserve battery power.
    B-rock

  • My iphone 6 wont turn on after i updated it and it doesn't work to restore it in itunes. what should i do?

    my iphone 6 wont turn on after i updated it and it doesn't work to restore it in itunes. what should i do?

    Hello ole-gunnar,
    Thanks for using Apple Support Communities.
    If your iPhone is unresponsive after updating your iOS version, then I'd like you to please follow the troubleshooting below.
    If you see a black screen
    You might need to charge your device before it can turn on. Plug in your device and let it charge for at least 10 minutes (20 minutes for iPad), then try turning it on. 
    You should see a battery icon while your device is charging. If you continue to see a black screen, reset your device. If your device doesn't respond when you press buttons
    Your device might not return to the Home screen when you press the Home button, wake from sleep when you press the Sleep/Wake button, slide to unlock or power off, or it might appear frozen. Try these steps:
    Restart your device.
    If it still doesn't respond, or if it doesn't turn back on, reset your device.
    If your device gets stuck during startup
    When starting up, you might see the Apple logo or a red or blue screen for a long time, or your device might restart again. Try these steps:
    Make sure that you have iTunes 12 or later on your computer.
    Put your device in recovery mode.
    When you get the option to restore or update, select Update. This will reinstall iOS without erasing your data.
    Get more help
    If you still need help after trying the steps above, contact Apple Support. 
    If your iPhone, iPad, or iPod touch doesn't respond or doesn't turn on - Apple Support
    Cheers,
    Alex H.

  • My ipod nano is not turning on,I have tried many different things.help asap

    My ipod nano is not turning on. I've tried many different things to turn it on such as press and hold menu and the select(center) button for 6-10 seconds and wait for ipod logo to appear. that does not work for me. Also the one where I move the button on the upper part of the ipod nano and moving it to the hold position and back and there againa and back. nothing seems to work...PLEASE HELP ME ASAP!! my friend thought that the battary could be so dead that it is not turning on at all. I remember charging it for about 4 hours and having full battary and the next day after charging the ipod nano it went dead!! it just shut off. what should i do...help me
      Windows XP  

    Go step by step.
    http://support.apple.com/kb/TS1365
    Note: Steps 5 and 6
    Step 5
    Reset SMC.     http://support.apple.com/kb/HT3964
    Choose the method for:
    "Resetting SMC on portables with a battery you should not remove on your own".

  • My ipod nano 2nd generation turn off by itself

    my ipod nano 2nd generation turn off by itself and when i unplug the USB cable and i plug it again its shows sign do not disconnect then its shows battery low and it turn off again i bought it since 2 and every time i go to the shop to repair it he told me that i don't have the parts to repair it please help any ideas ? thanks

    Try calling the apple customer service maybe they will hel you. 1-800-my-apple(this is the phone number) By the way this problem is very weird. You should call.

  • My ipod touch 5 wont turn on. It was working fine about an hour ago and now it does tot respond to any action i take.

    My ipod 5 suddenly wont turn on and is not responsive to any action, what can i try?

    Try:                                               
    - iOS: Not responding or does not turn on           
    - Also try DFU mode after try recovery mode
    How to put iPod touch / iPhone into DFU mode « Karthik's scribblings
    - If not successful and you can't fully turn the iOS device fully off, let the battery fully drain. After charging for an least an hour try the above again.
    - Try another cable              
    - Try on another computer                                                       
    - If still not successful that usually indicates a hardware problem and an appointment at the Genius Bar of an Apple store is in order.
    Apple Retail Store - Genius Bar                                     

  • Help my Ipod suddenly stopped working 2 min after unplug from car......

    Help my Ipod suddenly stopped working 2 min after unplugging it from my scion pioneer ipod ready radio. I am not sure what happened; it was working fine and charged sufficiently and i walked into the gym and tried to turn it on, and no life. I tried plugging it back into my car and it says "i-pod read error". I then tried to plug it into my computer and it doesnt even read it. I may have unplugged it when it said do not disconnect; i am not sure though.Any suggestions? thanks!
      Windows XP  

    I'd say your "Scion Pioneer" radio fried your Mini; could have been a power surge, or could be a bug.
    You might want to go the "aux jack" route next time.

  • What do you do if you charged your ipod but it wont turn on?

    My ipod wont turn on after I charged it.

    That sounds interesting...did you try:
    -Connecting it to your computer + syncing it
    -reseting the device
    That's all I could come up with. Let me know if it works.

Maybe you are looking for

  • New to SOAP - Can't log in

    I'm attempting to talk to one of our development post offices using soapui 3.6.1. On sending a soap login request, I'm getting back a 400 error. On the PO screen, I see Code: 11:44:51 048 SOAP Action Return Code = ea01 The http trace from soapui show

  • I still cannot view flash players in firefox after uninstalling and reinstalling firefox and flash multiple times. how do i fix this issue perminantly?

    I can go into chrome without any issues and watch any video without any problem. the second i get into firefox nothing works. i have had this issue on and off for years. i really do not see why you cannot fix this if everybody else can. i have uninst

  • Why won't my iPad 1 set-up on PC?

    I am trying to set up my iPad1 on my PC. I have iTunes open, and I connected the cord from the iPad to the USB port, but the screen is still black and the iPad is not appearing in iTunes. I have tried pressing the power-on button, but it won't work.

  • Using imported archive in UDF using import statement

    Hello Expert, I am trying to use the class of keystore_api.jar which is impoted in imported archive in my UDF using the import statement com.sap.engine.interfaces.keystore.KeystoreManager but I am getting the error package com.sap.engine.interfaces.k

  • ITunes 7 on CD

    How can I get the new version of iTunes on CD? I use dial up and trying to download it from the internet does not work.