IPOD nano 4GB Sleeps and wakens on its own

I have a nuciance problems hopefully someone can educate me on how to fix.
I have 60+ hours of audiobooks on my Ipod Nano 4GB which I listen to non-stop in my car using an iTrip connector.
The Ipod goes to sleep:
1. every 18-20 minutes of use
2. it always has 0.12 or 0.13 on the time left at the lower right of the window everytime
3. it stay asleep 40-50 seconds every time
4. it picks up exactly where it went to sleep!
During this sleep period the Ipod beeps when I try to use the keys but nothing happens and nothing changes when it awakens. I have found the best solution is to do nothing and let it awake on its own.
Any suggestions anyone? Thanks from a new user....
IPODnano 4GB   Windows XP  

That's a new one (if you like to be the first at things, then congrats!). Uh, let's see.
1. After hitting play, turn the Hold switch on. Does that fix it?
Also, try Restoring the iPod.
Check these out:
5Rs
5Rs Tutorials
Restoring iPod to Factory Settings
If neither of those work, you may need to have your iPod sent in for service:
iPod Service Request
I hope this helps!

Similar Messages

  • 6th gen iPod Nano volume keeps going down on its own

    It's been getting worse lately. It started happening towards the end of each of my run, but now even when I leave it on my desk, I can see the volume just move down on its own to zero. It is very unreliable and during long runs, I have to keep battling with the volume (it goes down on its own, and I have to bring it back up again). Shutting the iPod Nano off and turning it back on doesnt help.
    Anyone else encounters this? What should I do? My iPod Nano is about 1 year old.

    This issue is usually the result of the Nano coming into contact with moisture (likely from your workouts).  Try putting the iPod into an uncooked bag of dried rice and leaving it sit for a few days.  This should absorb any moisture in the iPod.
    After the few days are up, give it another whirl.  If the problem persists, connect the Nano to iTunes and restore it to factory settings.
    Otherwise, the damage may be permanent, meaning you'll need to have your iPod serviced or replaced.
    B-rock

  • Desperate - my nano has locked and frozen on its own!

    I am desperate for advice. My nano is less than a week old. The lock symbol suddenly appeared, I have tried every action recommended and now it is totally frozen, I can't use it at all. Am considering it is faulty? Has anyone had this problem?
    nano 2gb   Windows XP  

    Hi musica,
    I'm glad it helped you.
    Ummm... if it wouldn't be too much trouble, maybe you could fill out your computer and os information? Just click on My Settings in the right column. That way, whenever you're experiencing any kind of problem, the right people using the same/similar setup as yours will be able to offer the proper help.
    Gary

  • Formatted my new iPod Nano 4Gb and my application can't find the Device ID

    Hi,
    Just bought a new Nano 4Gb, updated it to 2006-06-28 (1.2) and of course it couldn't be recognized by Windows after that. Followed the instruction and formatted the Nano and made a Restore, worked fine!
    Now to my problem, when using my application Anapod Explorer (from www.redchairsoftware.com) it can connect to the Nano but it says the iPod don't have any Device ID so it can't authenticate to the iPod...
    Anyone more who is using this superb software?
    It seems like if some information is missing in the iPod after the formatting of it...
    Please advice!
    Best Regards

    Additional Information:
    Since some information seems to be missing on my iPod Nano 4Gb I compared the files with my iPod Video 60Gb.
    Comparing the directories: [driveletter]:\iPod_Control\Device
    on my iPod Nano 4Gb and my iPod Video 60Gb
    iPod Nano 4Gb:
    The file SysInfo is empty, containing no data when opened in Notepad.
    iPod Video 60Gb:
    The file SysInfo is of 1KB and another file named "_unlocked" is present.
    The information in the SysInfo file is:
    BoardHwName: iPod M25
    pszSerialNumber: JQ6040HFTXL
    ModelNumStr: MA147
    FirewireGuid: 0x000A270014E1CDBA
    HddFirmwareRev: BU011A
    RegionCode: S(0x0006)
    PolicyFlags: 0x00000001
    buildID: 0x06128000 (6.1.2)
    visibleBuildID: 0x01128000 (1.1.2)
    boardHwRev: 0x00000000 (0.0 0)
    boardHwSwInterfaceRev: 0x000B0005 (0.0.11 5)
    bootLoaderImageRev: 0x00000000 (0.0 0)
    diskModeImageRev: 0x00000000 (0.0 0)
    diagImageRev: 0x00000000 (0.0 0)
    osImageRev: 0x00000000 (0.0 0)
    iPodFamily: 0x00000000
    updaterFamily: 0x00000000
    I have done the diagnstic test on the Nano and there are no errors and the iPod Nano is functional but I can only use iTunes to load it with music, I can't use the wonderful Anapod Explorer.
    Another thing:
    When connecting my iPod Video to my computer it shows up with a drive looking like an MP3 player, when connecting my iPod Nano it shows up looking like an ordinary disc drive.
    Best Regards
      Windows XP Pro  

  • I have an ipod nano 4GB and use pc windows xp . since last year my ipod didnt sync any new songs saying "the ipod cannot be synced the required folder couldnt be found" and when i try to update the itunes version another error occured. plz HELP!!!!!!!!!

    I have an ipod nano 4gb and use pc with windows XP. since last year my ipod suddenly didnt want to sync any new songs saying " the ipod "MOAMEN" cannot be synced. the required folder couldnt be found" and when i try to update the itunes version another error occurs and i dont know when i tryed to format ipod i didnt find "format" button. so plz give me suggestions instructions i extremely bored !!!!!!!!!!!!!1

    Uninstall/Reinstall iTunes then try to rebuild the library.
    http://support.apple.com/kb/HT1925  (uninstall/reninstall)
    http://support.apple.com/kb/HT1451 (recreate library)

  • Ipod nano 4gb and car audio

    Hi everyone, I've got an iPod Nano 4gb and am a little confused as to what is required to connect this device to my factory installed cd player. I drive a 2006 Nissan Frontier Crew Cab and have the basic factory audio system. I spoke with the dealership where I purchased the truck and they said that I need an interface and harness for $400 + labor. I don't think that is an option for me -- way too expensive.
    What exactly is need to connect my iPod Nano to my truck's audio system? Do I need to purchase a new audio device that supports the iPod?
    Thanks

    The following website will list different types of car audio devices made for iPods. I hope it lists something that may help you.
    http://store.apple.com/1-800-MY-APPLE/WebObjects/AppleStore.woa/wa/RSLID?mco=567 F5736&nclm=iPodCarAudio

  • I rencently bought an ipod nano 6th gen and its an 16gb but it does let me downlaod many music i only have 353 songs and nothing elsewhat should i do

    i rencently bought an ipod nano 6th gen and its an 16gb but it doesnt let download much music as it suppose to and only have about 353 songs and i dont have any files on others.what should i do

    How many songs it will hold depends on the format and length of the songs.

  • I have ipod nano 4gb silver No: MA978ZP/A. IT IS NOT FUNCTIONING. WHEN I PUT USB INTO MY SYSTEM PORT, THE APPLE SYSTEM IN THE IPOD SCREEN IS BLINING ON AND OFF WHAT SHOULD I DO

    I have ipod nano 4gb silver No: MA978ZP/A. IT IS NOT FUNCTIONING. WHEN I PUT USB INTO MY SYSTEM PORT, THE APPLE SYSTEM IN THE IPOD SCREEN IS BLINING ON AND OFF WHAT SHOULD I DO

    See if this helps:
    iOS: Unable to Update or Restore

  • HT3215 Hi, I just got my new iPod Nano 4th Gen. and the screen is blank... It's not on and its plugged into my Mac OS X Mountain Lion. I don't know what to do. Help!?

    Hi, I just got my new iPod Nano 4th Gen. and the screen is blank... It's not on and its plugged into my Mac OS X Mountain Lion. I don't know what to do. Help!?

    If it is plugged into a USB hub (or the spare keyboard port), try connecting it to a direct USB port.
    Also, try doing this Reset procedure, while it is connect to power.
    http://support.apple.com/kb/HT1320
    NOTE:  A new iPod nano is 6th gen.

  • Ipod nano 4gb use itunes to restore востанавливаю все равно все тоже

    ipod nano 4gb use itunes to restore востанавливаю все равно все тоже

    restored my ipod and now it works but why does this happen? Is this a hardware problem, if it is, should i return my ipod. Or is this just a software problem that will be fixed in future updates?
    I'm not sure why exactly an iPod will say "Use iTunes to restore", but probably just because of a regular internal software problem.
    If you're iPod isn't displaying "Use iTunes to restore" anymore, and if it's acting fine, this was simply a isolated incident, which may occur now and then to a few iPods, if they're OS (operating system) gets messed up.
    It's similar to if your iPod once apon a time your iPod froze up, then displayed this symbol (it means you need to restore your iPod):
    You restored the iPod, and have never gotten that icon or any problems ever since.
    Will the need to restore your iPod recurr? It would only be by chance, and not relating to that isolated incident; this is, if you're iPod isn't displaying any failure messages soon after, which indicates a recurring true hard drive problem, not just a temporary one.
    If your iPod begins to display "Use iTunes to restore" or other failureful (that's my term for a symbol or behavior that indicates a failure) icons/messages soon after this, you can suspect that your iPod has a true problem with its hard drive/flash drive that a restore didn't fix.
    In this case, you would probably send your iPod in to Apple to get it repaired or replaced.
    I hope that explanation answers your question.
    -Kylene

  • My Ipod NANO 4gb keeps turning off at random times

    My Ipod NANO 4gb keeps on turning off at random times. The battery is fully charged, and i've updated the IPOD and ITUNES. What can I do?
      Windows XP Pro  

    Check the sleep option, maybe it being hit accidently. Maybe reset your setting on ipod, check background setting. Seems strange.Maybe use the hold button to lock ipod.

  • ITunes 6.0.1.3 not syncing Outlook Contacts or Calendar with ipod Nano 4GB

    I have Outlook 2003 installed and setup with a Microsoft Exchange Server. I have about 200 contacts currently stored in it.
    I recently purchased a ipod nano 4gb with hopes of syncing my contacts and calendar with that and being able to throw away my old Palm. The ipod nano works great for syncing music but I can't get it to sync either the calendar or contacts from outlook.
    I check the box for syncing contacts and choose Microsoft Outlook from the drop down. Then iTunes only gives me the option of syncing all contacts (which is fine with me) and I click Okay. Then I choose update from the ipod nano right click menu. The status bar says updating contacts but does not import any of my contact to my ipod. Also, except for the 1st time, the Permission Window asking for access to Outlook has not popped up again. When it did that first time, I was told that there was an error and itunes could not copy contacts over. Since then there have been no errors from iTunes.
    I have tried all the steps in the apple online help docs (unchecking boxes, restarting, re-checking, etc..) but can't find a solution. I don't want to have to manually Save As each calendar item and contact. Frankly, I'd rather just return the device.
    Can anyone help me?
    thanks in advance.

    Possible. It is just odd that the day before the update to 9.x.x (I forgot the release), it worked great. Following that upgrade, the sync died. I could reinstall the old release (per instructions from Apple Tech Support) and it would sync. However, not upgrading your iTunes means not upgrading your OS...and that is not an option. However, I think I will have XP reistalled on my machine...and then put a fresh install on iTunes...and see what happens.
    km

  • Using my iPod Nano 4GB (2nd gen) with the Fatman iTube's  remote control.

    I am using the iPod Nano 4GB with my new 'Fatman iTube' valve amp and dock.
    http://www.fat-man.co.uk/docs/product/itube_1.htm
    All works fine (beautiful sound) but only some of the remote control functions work.
    Volume and power off/on and treble/bass work fine but the iPod functions like skip and FF and playlists and menu dont work from the remote control.
    The company that make the amp (TLA) and the dealer (Audio T) both inform me that this is a common problem with remote controls on 3rd party iPod dock hi-fi systems and that Apple are not revealing when they will issue a software fix.
    It only happens with 2nd gen Nanos. All other iPod types talk with these remotes with no problem.
    I have been given a temporary 'workaround' by the manufacturer which is OK for now.
    Have any of you had similar problems between the 2nd generation Nano and remote controls on 3rd party (non Apple) hifi systems?
    Thanks
    iMac 20" Mac OS X (10.4.9)
    iMac 20" Mac OS X (10.4.9)

    hi,
    try the following article my friend...it will definitely resolve your problem..
    http://docs.info.apple.com/article.html?artnum=302420
    http://docs.info.apple.com/article.html?artnum=61711
    Regards,
    Sam

  • I have my ipod nano 5th generation and when i plugged it to my computer it is recognized but i cant do anything. On the ipod all i can see is a black screen with the apple sign! How can i fix this?

    I have my ipod nano 5th generation and when i plugged to my computer it is recognized but i cant do anything. On the ipod all i can see is a blackscreen with the apple sign! How can i fix this?

    Howdy Lumagofe,
    I was thinking that you may need to reset the iPod Nano, outlined here How to reset iPod http://support.apple.com/kb/ht1320.
    Press and hold the Sleep/Wake button and Volume Down button simultaneously for at least eight seconds or until the Apple logo appears. You may need to repeat this step.
    If the above step did not work, try connecting iPod to a power adapter and plug the power adapter into an electrical outlet, or connect iPod to your computer. Make sure the computer is turned on and isn't set to go to sleep. Try resetting the iPod while it is connected to power.
    If that doesn't quite get the iPod going again, then it will need to be restored. Use this article to help with that Restoring iPod to factory settings http://support.apple.com/kb/ht1339.
    All the very best,
    Sterling

  • IPod Nano 4GB from PC to iMac

    I have an iPod Nano 4GB that was formatted for Windows a couple of years ago. Shortly afterwards I bought and iMac and would like to like to be able to sync my iPod with the iMac. Most songs were loaded from CDs. However, a few were purchased from iTunes on the PC. What is the best way to move the entire iTunes library from the PC to iMac and allow synching between iPod and iMac going forward? Thanks.

    Thank you so much; I have been scouring these discussion forums for a solution to my problem!
    I was having problems deleting songs from my iPod and reclaiming the space, so I restored my iPod. Afterwards, I was only able to fit on about 50 songs on and had no idea what to do! I tried looked at dozens of discussions on here, tried the five r's, changed the drive letter, updated iTunes and my iPod...
    However, your post made me look at song sizes and I realised that the ones imported from my CDs were WAV and taking up over 1,000kpbs each!
    I'm currently importing songs from my CDs to iTunes again, this time into mp3 files!
    Thank you!!!

Maybe you are looking for

  • New iPod  Hi-Fi with issue

    Hi, I purchased a new Hi-Fi yesterday and haven't had any luck. It seems extremely easy to use but... I plugged the hi-Fi into ac power and the status light functions accordingly. The remote as well as the volume buttons also cause the status light t

  • Burned DVD contains same picture over and over

    I'm trying to make successful DVDs of 3,357 photos exported from iPhoto through the following process Share, successful Export, successful Resized(smaller), successful Make Burn folder, successful Drag images to Burn folder, successful Burn, FAILURE

  • Using the DBMS_LDAP PL/SQL package to access OID images

    Hey, I have built a script using LDAP to access the OID information for all the Portal users and store that information in a regular table in my database, but I am having some trouble retrieving the images associated with each user, so I was wonderin

  • Web Link as an underscore which is too long

    A web link in a PDF was updated with Adobe Acrobat 9 Pro.  The new URL is longer than the original.  As a result, the updated web link has an underscore that is too long.  I've tried shortening the underscore with the Link Tool as well as with the To

  • Privilege error ?????

    .Hello Friends.. I hav created a view called ' emp1 ' .. in the scott schema based on employees table which is in the HR schema ... my syntax was ........ " create or replace view emp1 as (select employee_id, last_name from hr.employees) " ... Now wh