IPod Nano - 7th Gen. No response, No Charge, No lights, No Joy

Bought the iPod Nano 3 months ago, and now it won't turn on, I have tried holding every combination of button and have not met success. Help????!!!!

Hello Abbey,
I would recommend the steps in this article named iOS: Device not recognized in iTunes for Windows found here http://support.apple.com/kb/TS1538. While the title of the article describes a symptom a bit different from yours, I feel the troubleshooting is still relevant.
If that does not resolve the issue, then I would suggest this article to help troubleshoot the USB connection.
iOS: Troubleshooting USB connection
http://support.apple.com/kb/ts1286
And lastly, resetting it just may do the trick.
How to reset an iPod nano (7th generation)
Press and hold the Sleep/Wake button and the Home button until the screen goes dark. The Apple logo should appear after a few seconds, then the Home screen should appear.
From: How to reset iPod
          http://support.apple.com/kb/ht1320
Take care,
Sterling

Similar Messages

  • IPod Nano 7th Gen says "Unsupported. Accessory is not supported" when trying to charge / sync

    iPod Nano 7th Gen says "Unsupported. Accessory is not supported" when trying to charge / sync with official apple lightening cable.
    It worked for almost a year then suddenly began to say that. My computer [windows], lightening cable and my power brick [all apple official] are all the same as they were when it was working. The iPod is almost a year old now, and has worked perfectly up until about a week ago.
    I have tried resetting the iPod, plugging it into different charging sources but it keeps saying "Unsupported. Accessory is not supported"
    Does anyone have any ideas on how to fix it?
    Thanks.

    Your iPod Nano firmware and iTunes updated to the current versions? 
    It is very difficult to offer troubleshooting suggestions when the "os version" you are using is unknown as each os has their own troubleshooting solutions. 

  • IPod nano 7th gen not charging

    I recently got an iPod nano 7th gen 16GB slate. Whenever I plug it into my MBP using the new connector, I get the PLUG in the battery icon instead of the usual lightning. When I finally unplug the iPod after keeping it plugged in for quite a long time, it seems like I didn't charge my iPod at all (all I get in the battery icon is a red line).
    Is there something wrong with the battery or the cable??

    Whilst charging make sure your iMac doesnt go to sleep and try to make sure itunes is constantly open whilst connected. If this does not work try restarting the device by holding down both the home button and slep button down.
    Hope this helps

  • Charging iPod nano 7th gen

    How long should I charge my ipod Nano 7th gen for maximum charge?

    The battery meter in the top corner seem to always stay at about 90% and would never fill up the entire way, But I just went to the store today and bought a new charge chord and that seems to have fixed the problem. Thank you for trying to help I appreciate it.

  • Ipod nano 7th GEN no audio out from head phones jack

    I am trying to use my Ipod nano 7th Gen with a monster wireless remote that connects to the charging and sync connection. The remote works fine and I can control the Ipod just fine with it, but when I connect the headphones to the headphone jack there is no audio. If I remove the wireless remote receiver from the charging sync connection the headphones jack works just fine. I am using a lighting speed to a 30 pin adaptor because the monster remote receiver is of the 30 pin format if that matters.
    Please let me know if this is normal or if there is a work around. My intention is to use the Ipod connected to a motorcycle sound system using the headphones connection to connect it to the motorcycle system amp and control the Ipod wirelessly.
    Thank you!

    Can you provide a link to the monster product, or the model name/number?  If it's a Bluetooth product, it seems superfluous to connect the receiver to the dock connector, because the 7th gen nano has built in Bluetooth.
    So, IF the remote control device is Bluetooth, you may be able to pair to it from the nano without connecting the receiver device to the dock connector.
    If it's not Bluetooth, you may be able to find an equivalent remote control device that IS Bluetooth, and not need to connect anything to the dock connector, which seems to be the source of the problem.

  • Ipod nano 7th gen stuck on apple logo screen

    New iPod nano 7th gen.  At first attempt to upload songs, was prompted to update software.  So, software was updated and as I was installing software update to the iPod, I got a message stating that the iPod was in the process of a restore (I think this is what it said.  I didn't pay a whole lot of attention as i was not expecting any problems).  I continued with the restore because nothing had been uploaded to the iPod yet so nothing would be lost.  At this point, the device has been stuck on the apple logo screen for a couple of hours now.  The only response I can get from it is when I do a reset.  The screen will black as it should and then go right back to the logo and stay.  Please help.....Son not happy as this was one of his Christmas presents this morning.  Really not looking forward to a trip to the apple store on the day after Christmas.

    I am afraid yo need to visit the store and possibly ask for a replacement. In some cases, doing the reset will correct any issues, but by the way you describe it, it freezes with apple logo. Better to get a replacement.

  • Why does my replacement iPod nano 7th gen not sync?

    I've just got a replacement iPod nano 7th gen after my last one was faulty (suddenly having white screens etc) - exact same model type. I've charged it, and when I put the new replacement iPod in the computer it makes the regular sound to let me know its recognised the iPod. The iPod shows the 'connected - eject before disconnecting' sign so that part of it seems to be working.
    I then go to devices looking to sync the music into my new iPod and then when I do that the 'Sync' button is grey and will not let me progress to sync. This is the problem I am having and I need help.
    Let me know if you need any more information, thank you.

    I am a UK resident btw If that helps.

  • Does anyone know where I can buy a replacement digitizer metal bezel for an iPod nano 7th gen.q

    Does anyone know where I can buy a replacement digitizer metal bezel for an iPod nano 7th gen That was broken (in 2 places) during disassembly.
    The lcd screen and digitizer were both replaced but the top 1/3 inch of the screen doesn't respond to any touch.

    They have 2 parts for sale for the nano 7th gen.  Ac adapter and charging cable.  I need to find one of those Chinese parts sites, they seem to have items that you cannot find in the states yet.

  • My ipod nano 7th gen is stuck on a loop of turning on and off.

    My ipod nano 7th gen is stuck on a loop of turning on and off, I've already done the reset, and everything that was recommended on other similar questions.  it isn't recognized by iTunes except in recovery mode where it allows me to restore but then goes right back to turning on and off once i'm back to normal play mode.  Once on recovery mode it works fine and doesn't turn on and off.  I've also uninstalled and reinstalled itunes to avail.  I'm super frustrated and am hoping that I won't need to buy a new one.  Is there anything else I can do before i just toss it out?  i'm getting a bit frustrated just watching my ipod turn on to the apple and then turn right back off.

    Hi there tksunrise,
    You may find the troubleshooting steps in the article below helpful.
    iPod nano (7th generation): Hardware troubleshooting
    http://support.apple.com/kb/TS4433
    Will not turn on or screen remains dark
    Connect iPod to power for at least ten minutes to ensure that the battery has enough charge to allow iPod to turn on.
    If iPod does not turn on after ten minutes, try resetting it while it is still connected to power. Reset the iPod by holding down the Sleep/Wake button and the Home button for at least six seconds or until you see the Apple logo appear.
    If the Apple logo appears on the display, connect iPod to a computer and verify that it appears in iTunes and can play music. If iPod appears in iTunes and can play music, no further troubleshooting is needed.
    If the screen remains dark and will not turn on, then your iPod may need service.
    Issue not resolved
    If the issue is still not resolved, please read this information on servicing your iPod.
    -Griff W. 

  • Whats the best heart rate transmitter for ipod nano 7th gen?

    Whats the best heart rate transmitter for ipod nano 7th gen:
    Polar WearLink+ Transmitter Nike+
    Polar H7 heart rate sensor
    Wahoo Fitness Blue HR
    Adidas miCoach heart rate monitor

    Calibrate your ipod by charging fully, then using it until it drains then charging it again. And resetting might help too.

  • Water damaged ipod nano 7th gen.

    I washed my ipod nano 7th gen. in the washing machine and it wont turn on. I tryed plugging it in to the charger and still wont turn on. Any help could help.

    Charging it while still wet will cause damaged to your nano. Try what deggie said.....
    You can try putting it in a bowl of raw rice for 4 to 5 days, charging it for a half-hour then resetting it while it is on the charger.
    I done this trick a few years ago with a 5th generation nano. It turned back on.
    Message was edited by: keeferaf

  • My ipod nano 7th gen has suddenly gone black and it wont turn on or connect to a power source.

    I was listening to my ipod nano 7th gen when it went black and the music stopped playing.  It wont turn on when i press the power button and when i connect it up to charge the screen doesn't turn on.  Can anyone tell me how to turn it on again or give me suggestions. 
    Much appriciated,
    MissC@t

    Hey MissC@t,
    Although the following article says 6th generation, most of the troubleshooting steps should still apply to your 7th generation nano. I'd go through the troubleshooting steps and see if that resolves the issue:
    iPod nano (6th generation): Hardware troubleshooting
    http://support.apple.com/kb/TS3474
    Have a good one,
    Delgadoh

  • After upgrade to Windows 8.1, ipod nano 7th gen not recognized

    /after upgrading to Windows 8.1, ITunes does not recognize my ipod nano 7th gen.  I have uninstalled and reinstalled ITunes but no luck.  I have gone through all steps in troubleshooting, but it still doesn't recognize it.  Help!

    Hi cindywindy,
    If your iPod Nano is no longer recognized in iTunes after a recent system upgrade, you may find the following article helpful (apologies if you have already seen it):
    Apple Support: iPod not recognized in My Computer and in iTunes for Windows
    http://support.apple.com/kb/ts1369
    Regards,
    - Brenden

  • I recently purchased a bluetooth headphone set that I have been able to pair to my iphone6 , but it is not showing up on my ipod nano 7th gen, anyone else had a similar problem ?

    anyone had trouble syncing a bluetooth headset to an ipod nano 7th gen ? I was able to sync to my iphone6 , but no luck with the ipod, even after a reset & several attempts

    THanks for the suggestion deggie , but I have already tried this without any success. I just mentioned pairing it to prove that the headphones weren't defective. I also tried reaeting the ipod through itunes hoping that might help , but still no detection on the ipod

  • Is there a way to listen to radio on iPod nano 7th gen with Bluetooth headphones?

    I know the iPod nano 7th gen uses the headphones as an antenna. I know there will need to be some sort of antenna attached. Does anybody know if there is an antenna on the market that can be plugged into the headphone jack that will allow audio to be sent to a pair of Bluetooth headphones?

    There is currently no such antenna available.
    B-rock

  • Ipod nano 7th gen not turning on or connecting to laptop??

    My son's ipod nano 7th gen won't turn on and when I connect it to the lap top a message comes up saying device driver not recognised - he was listening to it just last night, can anyone help? He's only had it since his birthday in November.

    I reset the ipod by holding down the power button and the menu button and the apple screen came up after a few moments - this seems to have done the trick!

Maybe you are looking for

  • Apple TV/Belkin Wireless G repeater

    I have to unplug my wireless repeater for Apple TV to show up in iTunes on my Macbook which is wirelessly connected to my network. Anything to be done about this? Don't want to have to unplug the repeater; it's useful.

  • I want the impossible?

    Hey folks. I have my iTunes library on our main, intel imac. I have an old, G3 ibook in the bedroom hooked up to a pretty decent set of speakers. It is currently running iTunes 6, as the specs for iTunes 7 requires OS X 4 Panther. The iMac and all of

  • Solaris Console Management crashing with java errors

    Hi, Whenever I am trying to run smc, it's crashing with following java errors: com.sun.management.viper.CriticalStopException: host1: host1 at com.sun.management.viperimpl.console.gui.SMCConsole.start(SMCConsole.java:280) at com.sun.management.viperi

  • How can i get this variable value into second page IN BSP

    Hi friends I have variable wk_matnr value 'ABC' in first page of BSP. How can i get this variable value into second page. Moosa

  • Disable automapping for specific users

    Hello All, I have a DL which contains the users list and i have to remove automapping feature for them. we have more than 3 sharedmailbox and 50+ users per sharedmailbox to disable this feature so i can't do it manually. Can someone please help me wi