IPod Nano Just Exploded!

It was a bit terrifying.
Shortly after ejecting my iPod Nano (very first generation - preordered before its release) that was charging, I placed it on a table nearby. A short time later I heard a pop. When I looked over I saw that flames were shooting out of my iPod. This occurred for about a minute. I am fortunate that nothing caught fire as I was ready to grab my fire extingusher. After it stopped flaming, white smoke shot out for a few minutes. Now, I still smell the burnt insides of my iPod.
Has this happened to anyone else here? Also, how can I contact support for this as this is quite a major safety issue. Earlier today I used my iPod while working out and luckily I did not get burned by my iPod.
I contacted support online and they should call me tomorrow. It said that they will charge me because I am past warranty, but please let me know if there is another direct way to reach them without getting charged.

Hey thanks for the tip, but they actually contacted me very shortly after as I think they saw this posting. So they are going to investigate it and send me a new Nano.

Similar Messages

  • My ipod nano just stopped working right after playing a song, any suggestions to get it back working?

    my ipod nano just stopped working right after playing a song, any suggestions to get it back working?

    Did the battery run out of power?  If not, try doing a Reset to "reboot" the iPod
    http://support.apple.com/kb/ht1320
    (A Reset does NOT erase the iPod.)

  • IPod Nano just froze for apparently no reason

    I have never once had a problem with my iPod Nano. I've never dropped it, scratched it or done any damage to it what so ever. (I've had it for about 3 months now)
    Just a few minutes ago I was listening to some songs on it. I hit the pause button and sifted through songs until I found what I wanted to listen to. I hit the pause button again to play the song and nothing happened. So I tried a different song and as I was sifting through to that song I noticed that the images that usually show the album artwork weren't showing up, just empty boxes. Then finally all the buttons stopped working.
    I tried holding down the menu and select buttons but that didn't work.
    I plugged it into my computer but iTunes didn't recognize it. I clicked on "My Computer" to see if it recognized it and I couldn't even get My Computer to open. It also froze. So then I unplugged my iPod Nano and My Computer opened up easily. So even though neither my iTunes software nor my My Computer actually show recognition on the screen, it seems to effect my computer when I plug the iPod Nano in.
    I can't make any sense out of it. Hopefully someone can help. Thanks!
    Jessica
    iPod Nano 2GB   Windows XP   Only 86 songs loaded so I don't think it's overloaded.

    I am having a similar problem. Twice now the screen has frozen - I can't scroll, or even turn it off. It does not dim. Once the battery wears down then I can plug it in and it will work again. Any ideas?

  • Help! My iPod nano just keeps shuffling thru my music

    iPod nano won't play anything. Just shuffles. I've tried a rest & a restore
    to factory settings, but, nothing seems to be working. Any & all
    suggestions will be greatly appreciated! 
    Thanx. Annie

    That was supposed to read, I've tried resetting & also
    a restore to factory settings. Sorry abt that

  • Ipod nano, just synced for the 1st time, frozen, how to reset???

    my new ipod nano (not sure which gen, just the very small square with only vol and on/off button), has frozen on a playing screen and wont connect to the computer or play or turn off or do anything??? how am i meant to reset it??

    Try #2 and #3 in link below. If neither work, you most likely have a hardware issue.
    Basic troubleshooting steps  
    17" 2.2GHz i7 Quad-Core MacBook Pro  8G RAM  750G HD + OCZ Vertex 3 SSD Boot HD 
    Got problems with your Apple iDevice-like iPhone, iPad or iPod touch? Try Troubleshooting 101
     In Memory of Steve Jobs 

  • Help, my iPod Nano just stopped working

    Help I've had my iPod nano 7th generation for about 6 months now.  It's always worked fine until one day after charging it, it will no longer turn on.  It does get hot when I try to charge it or reboot it (reboot using the home and on/off button together).  Can anyone please help?

    Hi AliPe!
    I have a website that I believe will help you troubleshoot this issue. The website is an iPod troubleshooting assistant, and it can be found right here:
    Apple - Support - iPod nano - iTunes Troubleshooting Assistant
    http://www.apple.com/support/ipodnano/assistant/itunes/
    Just follow the troubleshooting steps suggested by that website and you should be on the right track. Take care, and thanks for visiting the Apple Support Communities.
    -Braden

  • My iPod Nano just won't work anymore. Please help if possible.

    I have had my iPod Nano for under a year, and this past month it has been going crazy on me like for a week I was unable to turn it off. However, it all of sudden worked fine but two weeks later while I was listening to it, it just turned off on me. Now I cannot open it and I have tried charging it but nothing shows up and it just will not turn on. It is like my iPod has died. Has anyone else gone through this? Thanks for the help.
      Windows XP  

    Try these.
    My iPod won't turn on.
    iPod battery doesn't charge.
    My iPod won't wake up.
    iPod touch-wheel is unresponsive after waking from sleep.
    When restoring the iPod, it's recommended to put it into disk mode first.
    Putting iPod into disk mode.
    If none of the above help, then it's probably a service issue.
    You can arrange online service here.
    Service request.
    Or if an Apple store is near you, take it there and have them check your iPod.

  • My ipod nano just stops and now its dead

    ipod nano 7th generation just went dead, black screen

    Hey there jean-yves1961!
    I have a link here for you that can help you troubleshoot this issue:
    Apple - Support - iPod nano - iTunes Troubleshooting Assistant
    http://www.apple.com/support/ipodnano/assistant/itunes/
    Thanks for being a part of the Apple Support Communities!
    Regards,
    Braden

  • My ipod nano just turns off and on when i repeatedly plug in headphones and the sleep/wake button is disabled while I have my headphones plugged in

    My Ipod Nano basically switched the function of turning on/off when i plug in the headphones. I found a way to beat this by plugging in my headphones an even number of times, but when I do this, the Sleep/Wake button is completely rendedered useless. As soon as the screen turns off I cannot change songs by double clicking, but I am able to change volume. The same is for trying to sleep the screen. I have tried factory resetting the ipod and using different headphones but the problem seems like it is not affected by these steps. I also tried to clean out the headphone jack and the result is the same.

    Take the iPod Nano to an Apple store or an AASP.  Whichever is more convenient for you.

  • My iPOD nano just races through the songs

    Ok, my ipod, after clicking on any source of music (albums, songs, artists, etc..) shows each song for about one second, without even staying on the song long enough to hear anything. It just goes from song one to two to three to four, etc, extremely fast. It also does not show me any of the pictures for the albums. That is not a big issue for me, I just would really like to listen to my ipod again. Please help me in any way you can.

    Try reseting it (by holding the center button and the menu button at the same time)and if that dosen't work restore your ipod from the iPod updater.

  • My ipod nano just recorded my latest workout as happening in Jan 1970 and it won't/hasn't uploaded to Nike

    I completed and uploaded 2 runs a couple of weeks ago with no problem. I did one today and it hasn't uploaded to Nike+ despite synching my ipod.
    It has also recorded the run as happening on 4th of Jan 1970 even though the date and time are right on my ipod.
    Help!

    Just to update:
    When I look at my profile on the Nike+ website, the run appears as having happened on 4th Jan 2003 ('cause Nike+ doesn't go all the way back to 1970).
    I got in touch with the Nike+ support team who have said they will correct the "date stamp"  on my run and let me know when it's done.
    They also mentioned that this problem - date stamp being wrong - can occur if you let your ipod run out of charge completely (which I had done) or if you use a wall charger. I did charge using a computer that doesn't have iTunes etc and which isn't linked iwth my ipod so I guess both of these may have affected it.
    I still don't know how to change the date of the run on my ipod so it appears correctly in my history on there...wondering if when I sync it to Nike+ once they have corrected it that it will work..but doubtful!
    I also don't know what will happen when I do my next run so I still need help! Thanks!

  • My ipod nano just won't turn on. Please help!!!

    Ok. So yesterday I was listening to my ipod and everything and I realized it was running out of battery. So, before I went to work I placed it on the charger as usual. Now this morning I get up and decide I'm going to listen to it again and the screen is black and won't turn on. I even hooked it up to my computer and itunes won't recognize it. I placed it back on the charger and nothing. And, I even tried holding the menu button and the center button at the same time. (because that usually works, but, only when the screen showed the apple icon) And nothing has changed. Please please help me! I really hope it's not dead for good. It is older but there are songs on there i don't think i can replace again. Please help!

    Was this a wall charger?  I was told by an employee not to use a car charger to try and charge my 7th gen Nano.  Also, I plugged it into my work computer and it worked for 30 seconds and then went black. For some reason this kills the battery dead.  Computer wouldn't recognize it and it would not turn on UNTIL I took it to the Apple store and they plugged it up, then it worked.  If you can head to the Genius bar and get a quick once over. These 7th gens are very finicky!

  • Ipod nano just shows blinking apple logo

    I accidently disconnected my ipod when it said don't disconnect. Now the screen just blinks the apple logo and won't let me restart or restore or update and my computer doesn't even recognize it anymore. what can i do to fix it?

    A. Try to connect your iPod with another computer with the iPod updater pre-installed.
    B. Still can’t see your iPod, put it in Disk Mode and connect with a computer, instead of doing a Restore on iPod Updater. Go and format the iPod instead.
    For Mac computer
    1. Open the disk utility, hope your iPod appears there (left hand side), highlight it
    2. Go to Tab “Partition”, click either “Delete” or “Partition”, if fails, skip this step and go to 3
    3. Go to Tab “Erase” , choose Volume Format as “MAC OS Extended (Journaled), and click Erase, again if fails, skip it and go to 4
    4. Same as step 3, but open the “Security Options....” and choose “Zero Out Data” before click Erase. It will take 1 to 2 hours to complete.
    5. Eject your iPod and do a Reset
    6. Open the iPod Updater and click “Restore”
    For Window computer
    Go to folder “My Computer”
    Hope you can see your iPod there and right click on the iPod
    Choose “Format”. Ensure the settings are at “Default” and that “Quick Format” is not checked
    Now select “Format”
    Eject your iPod and do a Reset
    Open the iPod Updater and click “Restore”
    In case you do not manage to do a “Format” on a window computer, try to use some 3rd party disk utility software, e.g.“Partition Magic”.
    C. Windows users having trouble with their iPods should locate a Mac user. In many cases when an iPod won't show up on a PC that it will show up on the Mac. Then it can be restored. When the PC user returns to his computer the iPod will be recognized by the PC, reformatted for the PC, and usable again. By the way, it works in reverse too. A Mac user often can get his iPod back by connecting it to a PC and restoring it.
    Tips
    a. It does not matter whether the format is completed or not, the key is to erase (or partly) the corrupted firmware files on the Hard Drive of the iPod. After that, when the iPod re-connected with a computer, it will be recognized as an fresh external hard drive, it will show up on the iPod updater.
    b. It is not a difficult issue for a Mac user to find a window base computer, for a PC user, if they can’t find any Mac user, they can go to a nearest Apple Shop for a favor.
    c. You may need to switch around the PC and Mac, try to do several attempts between “Format” and “Restore”
    D. Format your iPod with a start disk
    I have not tried this solution myself, I heard that there were few successful cases that the users managed to get their iPod (you must put your iPod in disk mode before connecting with a computer) mounted by the computer, which was booted by a system startup disk. For Mac, you can use the Disk Utility (on the Tiger OS system disk), for PC user, you can use the window OS system disk. Try to find a way to reformat your iPod, again it does not matter which format (FAT32, NTFS or HFS+) you choose, the key is to erase the corrupted system files on the iPod. Then eject your iPod and do a Reset to switch out from Disk Mode. Reboot your computer at the normal way, connect your iPod back with it, open the iPod updater, and hopefully your iPod will appear there for the Restore.

  • IPod nano just hours old and it's frozen!

    First thing I did was plug it in to my laptop, and my iTunes recognized it and I set up iTunes with the ipod's name, etc. My iPod screen was showing the flashing "do not disconnect" for the 3 hours I had it plugged in and the battery symbol signified that it had been completely charged, with the plug symbol in the center... but I left it plugged in anyways. I synched up my ipod with the songs in itunes, and everything seemed fine until I ejected it and it went to the language select screen. The lock symbol was also showing in the upper corner, without the lock in the on position. I moved the lock back and forth with no change, and I could not select or scroll at all. I also reset several times and tried plugging it into a wall adaptor, still no change.
    Would it be easier for me to just return to the store than figure out what's wrong?

    yes! pls. return it back for replacement.

  • My ipod nano just died!!!!

    It won't turn on. I never dropped it, nor have I abused it. I can't believe this nonsense. I took extra measures to keep it scratchfree by leaving the plastic on, and now the whole thing is ruined. I ordered it from apple.com, what can I do?

    Breathe. Things sound OK. The "Do not disconnect" means either the Nano is being updated or is recharging. Simply eject it from within iTunes and your Nano interface should return and continue recharging. If you turn it off it should enter a dedicated recharging mode with a Big battery icon.

Maybe you are looking for

  • How to set up standalone wireless print server

    I need step-by-step instructions on to set up a KonicaMinolta bizhub multifunction printer to print wirelessly from various Macs. In other words, it would not be hooked up to the internet or my wireless network. I understand this can be done with an

  • Ipod Nano 2GB Not Playing Songs

    When I turn my Ipod on and try to play a song, it just cycles through all of the songs and does not play any of them, I can change my settings and look through the playlists but when I try and play one it will start acting up. Can anyone help? 1st Ge

  • I have a Lion content code for the free update. Is there a time limit on how long I have to download it

    I received a web order number and content code for my free update of Lion. Is there a time limit on how long I have before I must actually download the application? Thanks. JVC

  • DML Error Logging Tables?

    How can I use DML Error Logging Tables with OWB10gR2 (in tab-definition and mappings)? btw: what really is a shadow-table?

  • Help Creating a "Scenario Clock"

    Hi! I'm not new to Java, but I am having a big issue trying to find a specific clock that I'm looking for. I want a clock that displays the current time (Including day, month, and year), but I want to be able to set the clock to a time and date of my