IPod Nano screen = white and blank

Hey everyone. Okay, I've had my nano for about 6 months now, I bring it to school every day, and I haven't had any problems until today...
I went to go turn it on to listen to it, and i notice that the screen is plain white (backlight on) with a black bar on the right side of the screen that randomly shows up.
I have two questions- is this covered in the iPod 1 year warranty? If it is, when I bring it to the Apple store near me, would they let me upgrade (and pay the difference) to the 30 gig video?
Thanks everyone for your help (in advance).

Hello. i cind'a have the same problem.. My screen is dead, but the music is there still...
I have gone thru the "send i-pod to be serviced" thing.. but i haven't recieved an e-mail from apple, which the prosess told me i would get. So what is the adress i should send my broken ipod? it olso said that if they dont recieve an ipod after confirmen the "sevrice" thing, they would charge my Visa for about 160NOK = 25$
thanks..

Similar Messages

  • 6th gen ipod nano has white screen and won't go into disc mode

    My ipod nano has a white screen - it will play music, and it is recognized by itunes. It won't enter disc mode. I can't seem to find any other helpful steps to follow online other than put it into disc mode and restore it via itunes. When I attempt to put it into disc mode holding power/Vol down together the screen will turn back, but when I then hold down Vol down/Vol up together while the screen is dark it just goes back to white screen. I did plug it into the computer and restore it via itunes, and the screen is still white.  Any ideas?  Thanks!

    Hi LizS5,
    It sounds as if you have already done much of the troubleshooting suggested in this article, but I would suggest you work through it in order to get your iPod nano back up and running -
    iPod nano (6th generation): Hardware troubleshooting
    http://support.apple.com/kb/TS3474
    Specifically -
    Try putting the iPod into disk mode:
    Reset the device (press the Sleep and Volume Down buttons simultaneously until the display turns black—about eight seconds).
    When the display turns black, hold down the Volume Down and Volume Up buttons simultaneously until the device enters Disk mode.
    While the device is in disk mode, sync it to iTunes and try to restore.
    And if the issue is not resolved -
    My issue is still not resolved. What do I do next?
    For information on servicing your iPod, go to the iPod Service FAQ
    Thanks for using Apple Support Communities.
    Best,
    Brett L

  • HT3215 Hi, I just got my new iPod Nano 4th Gen. and the screen is blank... It's not on and its plugged into my Mac OS X Mountain Lion. I don't know what to do. Help!?

    Hi, I just got my new iPod Nano 4th Gen. and the screen is blank... It's not on and its plugged into my Mac OS X Mountain Lion. I don't know what to do. Help!?

    If it is plugged into a USB hub (or the spare keyboard port), try connecting it to a direct USB port.
    Also, try doing this Reset procedure, while it is connect to power.
    http://support.apple.com/kb/HT1320
    NOTE:  A new iPod nano is 6th gen.

  • The screen on my ipod nano 7th generation went blank

    the screen on my ipod nano 7th generation went blank, I can do, and try to restore in Itunes, but it makes the restoration and nothing happens the screen remains blank.
    I can do that

    Hello eramosf,
    I would be concerned too if my iPod nano had a black screen.  I recommend following the steps below:
    Will not turn on or screen remains dark
    Connect iPod to power for at least ten minutes to ensure that the battery has enough charge to allow iPod to turn on.
    If iPod does not turn on after ten minutes, try resetting the device while it is still connected to power. Press and hold the Sleep/Wake button and the Home button until the screen goes dark. The Apple logo should appear after a few seconds, then the Home screen should appear.
    If the Apple logo appears on the display, connect iPod to a computer and verify that it appears in iTunes and can play music. If iPod appears in iTunes and can play music, no further troubleshooting is needed.
    If the screen remains dark and will not turn on, then your iPod may need service.
    I got this information from the following article for the 6th generation iPod nano.  The steps are the same, except I updated the second step with the reset for the 7th generation iPod nano:
    iPod nano (6th generation): Hardware troubleshooting
    http://support.apple.com/kb/ts3474
    How to reset iPod
    http://support.apple.com/kb/ht1320
    Thank you for using Apple Support Communities.
    Best,
    Sheila M.

  • I got an iPod Nano for Christmas and loved it. Then the screen died. I got a replacement but it no longer repeats Playlists. Is it a setting I have to adjust to get it to repeat the entire Playlist?

    I got an iPod Nano for Christmas and loved it. Then the screen died. I got a replacement but it no longer repeats Playlists. Is it a setting I have to adjust to get it to repeat the entire Playlist?

    Make an appointment at the genius bar.
    If you went without an appointment, then it would make sense that you could be turned away.

  • I got an iPod Nano 3rd Generation and it has scratches on the screen, and the warranty is already expired. Can it be repaired and how much is it going 2 be.?

    I got an iPod Nano 3rd Generation and it has scratches on the screen, and the warranty is already expired. Can it be repaired and how much is it going 2 be.?

    Hello HernanOtt,
    Depends on where you have it serviced.  Here are Apple's repair quotes.
    http://www.apple.com/support/ipod/service/prices/
    You would probably save a lot of money by having a 3rd party repair company do the job for you instead.  Just do a simple Google search for iPod repair and you'll get a plethora of results.
    B-rock

  • My iPod nano screen is frozen and will not respond. It shows the song which was playing is paused, but will not resume playing. I have held down all controls, and changed the slide switch, but nothing happens

    my iPod nano screen is frozen and will not respond. It shows the song which was playing is paused, but will not resume playing. I have held down all controls, and changed the slide switch, but nothing happens

    Hi Goofy Goat,
    Welcome to the Apple Support Communities!
    It sounds like you have done some great troubleshooting for your iPod nano that is not responding. In this situation, if resetting it did not resolve, I would suggest restoring the iPod back to its factory settings and then sync your content back onto it from iTunes. Please use the following article as a resource for restoring.
    Restoring iPod to factory settings
    http://support.apple.com/kb/HT1339
    Have a great day,
    Joe

  • I have my ipod nano 5th generation and when i plugged it to my computer it is recognized but i cant do anything. On the ipod all i can see is a black screen with the apple sign! How can i fix this?

    I have my ipod nano 5th generation and when i plugged to my computer it is recognized but i cant do anything. On the ipod all i can see is a blackscreen with the apple sign! How can i fix this?

    Howdy Lumagofe,
    I was thinking that you may need to reset the iPod Nano, outlined here How to reset iPod http://support.apple.com/kb/ht1320.
    Press and hold the Sleep/Wake button and Volume Down button simultaneously for at least eight seconds or until the Apple logo appears. You may need to repeat this step.
    If the above step did not work, try connecting iPod to a power adapter and plug the power adapter into an electrical outlet, or connect iPod to your computer. Make sure the computer is turned on and isn't set to go to sleep. Try resetting the iPod while it is connected to power.
    If that doesn't quite get the iPod going again, then it will need to be restored. Use this article to help with that Restoring iPod to factory settings http://support.apple.com/kb/ht1339.
    All the very best,
    Sterling

  • Ipod nano screen fade then locks

    has anyone had this problem where if you hold the menu button down, then the 2gb black ipod nano locks up and the image on the screen fades away slowly until the lcd is blank? then the nano won't start up anymore (until it is plugged into a computer). toggling hold does not work, and pressing both the menu and center button doesn't do anything either. is this a defect for my particular nano or is this possible some kind of software bug that needs some kind of restoring?
    also, on a related note, plugging it in to the computer (xp) sometimes brings up the apple logo then it jumps to a discharged battery lightning logo (battery is full). i have to keep plugging/unplugging until i get to the "do not disconnect" screen, then the nano works fine and shows the full battery on the upper right (to prove its charged).
    any help on this would be great, thanks!

    I figured out the cause of this problem, basically if you reset your ipod (menu and center), then the nano freezes and the screen image fades... has anyone had this problem? I'm also having a very very difficult time trying to get the nano back to a working state since none of the buttons work... when i plug it in to the computer, the screen shows an apple, backlight flashes on for a second then goes away, and it quickly jumps to a lightning bolt battery... unfortunately the battery is fully charged (green) from before the nano froze, and constantly plugging/unplugging the usb connector sometimes brings the nano back to normal working condition...
    I was wondering, what happens on a normal nano when you reset it (menu and center) without being plugged in... does it freeze as well?
    I also tried a full restore via ipod updater when i finally got it working, but the problem still exists and i hit menu+center and froze it and now i am plugging/unplugging to the computer to try to get that 1% chance it will boot up properly... any advice?

  • Got a refurbished iPod Nano 6th gen, and went to connect it to my PC,

    Got a refurbished iPod Nano 6th gen, and went to connect it to my PC, it said it was configured to Mac and went to restore it and install software. Now shows white screen with little computer icon and warning sign. won't reset

    By a reset, I assume you mean pressing and holding both the Sleep/Wake and Volume Down buttons together long enough for the Apple logo to appear?
    Can you try and force the Nano into Disk Mode and then connect it iTunes and restore it again?
    Putting iPod into Disk Mode
    B-rock

  • Huge Ipod nano screen problem

    I have a big problem with the iPod Nano screen. It just doesn't work. I have tried reseting the ipod, restoring it but it just doesn't work.
    It is not a screen problem because when I plug it on to the PC the screen lightens up with just white on it.
    I could listen to the song by "blindly" selecting Shuffle. But now I can't even do that.
    I would REAALY appreaciate any help.

    If you can get one sent or brought down to you, you can replace it yourself It is not that hard to do, or I am sure you can find someone to do it for you. I live in Mexico and it is hard to get parts to us, there is also no repair place close, but we have people come from the states every once and awhile and they bring us parts so we can repair our own. Go on ebay and you will find screens for under 15 dollars U.S. and it comes with the tools that you will need to open your nano. Hope this helps.

  • Ipod nano screen

    Can anyone please tell me - ( I have spent many hours on the apple website looking for contact details of a real person; but no good )- what to do with my IPod Nano screen that does not work. It is not cracked but is very bright, unreadable and seems to have gibberish on it.
    I have tried the RESET trick but can see nothing on the screen.
    I live near DUBAI and nobody will talk to me about the problem. I won the thing in a competition last December and it only worked for a few weeks.
    Please help me Obeonekinobe, you're my only hope.
    Chapwoman
    Nano   Windows 98  

    Try these steps one at a time.
    The Five Rs.

  • IPod Nano is lagging, and no music is playing. Headphones work. Half battery. ***, mate?

    I went to use my iPod Nano this morning and it won't play music. My headphones work, and it still makes the sound when I shuffle it. It also appears to be significantly lagging by 2-3 seconds. I have a half battery. What's going on?

    If none of the 5 R's of troubleshooting are able to solve the problem, the issue is hardware related, meaning you'll need to have the iPod serviced or replaced.  The LCD screen may have simply burned out or wore out over time.
    http://www.apple.com/support/ipod/five_rs/.
    It wouldn't also hurt to the let iPod's battery full drain. Then charge the iPod back up and go through the 5 R's again.
    B-rock

  • Ipod nano screen completely messed up

    I've noticed recently that my Ipod nano screen has become totaly messed up, i can only see the top half of it,where it says Music, Photos, etc. and even that is all deteriorated,whilst the bottom almost look's like a barcode. Although i can still listen to music, volume is inacessible.
    Could some one please help me on this, i just got this recently by winning it from a local radio station and I dearly love it, help would be appreciated.
    PS: this is not something physicly on the screen or the result of a scratched screen, it's the actual inside, where the song information etc. is viewed.
      Windows 98  

    Hi,
    Welcome to Apple Discussions
    You might want to try this link:
    Resetting iPod if it appears frozen or doesn't respond
    According to the Tech Specs (http://www.apple.com/ipodnano/specs.html) Windows 98 isn't supported - could that be the answer?
    Windows system requirements
    * PC with USB port or card (USB 2.0 recommended)
    * Windows 2000 with Service Pack 4 or later, or Windows XP Home or Professional with Service Pack 2 or later
    Regards
    Colin R.

  • TA44551 My 1-year ipod nano locked up and would not start overnight. The on/off button will not work and stopped holding charge. No water damage, no fall, nothing unusual. I restored it (twice) but it will still not hold charge and on/off does not work.

    My 1-year ipod nano locked up and would not start overnight. The on/off button will not work and stopped holding charge. No water damage, no fall, nothing unusual. I restored it (twice) but it will still not hold charge and on/off does not work. I tried to restore it again and charged it in three different locations with different cables. etc but nothing. Suggestions?

    - After charging for 1/2 hour or so, does iTunes see the iPod?  If yes, restore the iPod from backup.
    - If no, se if placing the iPod in recovery mode will make it visible so you can restore the iPod.  For recovery mode see:
    iPhone and iPod touch: Unable to update or restore

Maybe you are looking for

  • To know the Finish Good or FInish Product name

    i am developing an Batch wise consumption report, in that i want to know the finish product name, is there any FM or a table where we can find the name of the Finish Goods or Product name,,, Regards Mukesh Kumar M

  • Acrobat Pro 6 & Word 2007

    Have a pdf document that I can open and edit in Pro 6. However, when I save out as a word.doc document and open it in Word 2007, all I have is an image of the document that I cannot edit. Any suggestions as to what I'm failing to do? Many thanks for

  • Problem in deployment (BPM 11g Suite)

    Hi, I am using BPM 11g suite and created one sample BPM project. But while deployment I am getting some error and not able to deploy my process. While deployment I am getting the following error: [12:28:31 PM] Deploying 2 profiles... [12:28:31 PM] Wr

  • Duplicate apps launching

    In Mavericks 10.9.5 I've been having duplicate copies of apps launching. I've noticed it w/Mail & Acrobat Pro. Don't know what causes it - can't duplicate it intentionally, just noticed that it's been happening lately.

  • No Finder and renaming the "DivXNetworks" folder does not work.  What now??

    I just upgraded to 10.5 on my MacBook and I am having the same finder issues discussed in the following thread: http://discussions.apple.com/thread.jspa?threadID=1197076&tstart=15 But when I try the suggested solution, I am being told that I do not h