Ipod says I'm connected to wifi, but I'm really not.

My ipod keeps saying I am connected, but nothing requiring internet will load. Advice?

Check your IP address from the details of your connection. If it starts with 169 then your router is not giving you a valid IP adderess and you will be unable to use the Internet.
Sometimes restarting your router by removing power will cure this problem.

Similar Messages

  • My ipod says it is connected to wifi but internet wont launch

    it shows the bars that it is connected to wifi then it doesnt launch the internet or anything that uses internet is there anything wrong with my ipod like should i go to a tech speacialist to fix the hardware on my ipod or does it have to do with the router or anything like that?

    Try going to Settings>WiFi, then tap the arrow to the right of the active wifi connection. Then scroll down and tap Renew Lease. That may free up the connection.

  • Says I'm connected to internet but I'm really not - iPad2

    My iPad2 says it's connected to the internet, both in the settup (there is a check) and the range is full in the top left corner of the screen.  However, when I open Safari or any app requiring internet, it says there is no internet connection.

    Look at iOS Troubleshooting Wi-Fi networks and connections  http://support.apple.com/kb/TS1398
    iPad: Issues connecting to Wi-Fi networks  http://support.apple.com/kb/ts3304
    iOS: Recommended settings for Wi-Fi routers and access points  http://support.apple.com/kb/HT4199
    Additional things to try.
    Try this first. Turn Off your iPad. Then turn Off (disconnect power cord) the wireless router & then back On. Now boot your iPad. Hopefully it will see the WiFi.
    Go to Settings>Wi-Fi and turn Off. Then while at Settings>Wi-Fi, turn back On and chose a Network.
    Change the channel on your wireless router. Instructions at http://macintoshhowto.com/advanced/how-to-get-a-good-range-on-your-wireless-netw ork.html
    Another thing to try - Go into your router security settings and change from WEP to WPA with AES.
    How to Quickly Fix iPad 3 Wi-Fi Reception Problems
    http://osxdaily.com/2012/03/21/fix-new-ipad-3-wi-fi-reception-problems/
    If none of the above suggestions work, look at this link.
    iPad Wi-Fi Problems: Comprehensive List of Fixes
    http://appletoolbox.com/2010/04/ipad-wi-fi-problems-comprehensive-list-of-fixes/
    Fix iPad Wifi Connection and Signal Issues  http://www.youtube.com/watch?v=uwWtIG5jUxE
    ~~~~~~~~~~~~~~~
    If any of the above solutions work, please post back what solved your problem. It will help others with the same problem.
     Cheers, Tom

  • My ipod touch says it is connected to wifi, but won't run anything that uses it like safari or itunes, and I don't know how to fix it

    Can anyone help me? my  ipod touch says it is connected to wifi, but it won't run anything that uses wifi like safari or itunes, and I don't know how to fix it

    You didn't indicate if it ever worked.  If it NEVER did, the problem could be caused by a firewall in the router.  For reasons that I do not understand, that will affect IOS (iPod/iPad) communication but will not affect computers or other devices.
    You will need administrative access to the router.  If a firewall is present, turn it off and test the iPod again.  If it works, turn the firewall back on but weaken it a notch and test the iPod again.  Repeat as required.

  • My computer says I am connected to wifi, but when I go to use the internet, I am not connected. What do I do?

    I have tried to reset my wifi and use different wifi systems. I am in college, so I have tried to use the internet both on campus and in my home in Dallas, neither of which worked. I JUST WANT TO HAVE INTERNET.

    My computer says I am connected to wifi, but when I go to use the Internet, I am not connected.
    Usually when this occurs on one Wifi and Internet connection, the wifi router is working, but the router connection to the Internet Service Provider is broken. Resetting the modem or router/modem combination often results in a new connection to the ISP being established (baring any data caps limits, line, modem or ISP troubles)
    However your mentioning it's not connecting anywhere your going on wifi or Internet, which could mean your machine has been compromised and possibly blacklisted until it's cleaned up of malware, or you tried to self solve your earlier issues and messed up your Network settings.
    I tend to lesser think it's a actual hardware problem, but it might come to that eventually.
    You should test the compromised/blacklist theroy by using a Ethernet cable to the modem you know has a good Internet on and powering on/off the modem. (if a router/modem combination, then no need). If you get Internet and not kicked off in a few minutes, then your machine is fine, likely messed up Network settings are too blame.
    You can clear everything out by creating a New Location by editing locations and creating a new one, also by going to Airport Advanced > Airport and deleting all the previous connections to start over new. Reboot.
    Connect manually to your home network and save in Keychain when it asks.
    If this is all too much for you, take it to a local PC/Mac repair shop as they specialize in software/network issues.

  • Says i'm connected to wifi, but my 3G symbol doesn't change,

    Says i'm connected to wifi, but my 3G symbol doesn't change. Also, i'm not really connected because my internet doesn't work, but all my other devices work fine on my home wifi.
    null

    IT'S BLUETOOTH: Iphone 4 keeps dropping wifi when I select a photo to airplay to my atv2. I have just figured out the airplay issue with PICTURES from the iPhone camera roll. It's BLUETOOTH. When I turn blue off, airplay of photos works perfectly solid and responsive. Turn blue on, it breaks wifi. This is definitely the conflict, it's night and day. There is definitely interference in there somewhere.

  • HT1430 My iPad isn't getting connection to internet.  It just suddenly stopped!  It says it is connected to WiFi but it just keeps spinning and nothing will come up.  Have tried rebooting my router and iPad (my other computer is connected just fine).

    My iPad isn't getting connection to internet.  It just suddenly stopped!  It says it is connected to WiFi but it just keeps spinning and nothing will come up.  Have tried rebooting my router and iPad (my other computer is connected just fine).

    Try turning WiFi off on the iPad, then reset it again, turn WiFi on again and join your network again if necessary. Or go to Settings>WiFi>Your network name>Forget this network. Reset your iPad and then join your network again. Or - settings>General>Reset>Reset network settings. Reset the iPad, then try to join your network again.

  • Younger brother has forgotten his passcode..ipod says i must connect to itunes but this ipod has never been connected before..help!

    my younger brother recently got an ipod touch. since he has had it i have used my apple id to download apps for him; the ipod was never connected via wire to a computer. he has forgotten his password and the ipod is saying i must connect to itunes but i know it needs to be connected to an itunes used previously..there is no itunes used previously in this case. what must i do to reset the ipod to factory settings? thanks

    If You Are Locked Out Or Have Forgotten Your Passcode
    iTunes 10 for Mac- Update and restore software on iPod, iPhone, or iPad
    iPhone, iPad, iPod touch: Wrong passcode results in red disabled screen
    iOS- Understanding passcodes
    A Complete Guide to Recover Your iDevice if You Forget Your Passcode
    If you cannot remember the passcode, you will need to restore your device using the computer with which you last synced it. This allows you to reset your passcode and resync the data from the device (or restore from a backup). If you restore on a different computer that was never synced with the device, you will be able to unlock the device for use and remove the passcode, but your data will not be present. Refer to Updating and restoring iPhone, iPad and iPod touch software.
    Try restoring the iOS device if backing up and erasing all content and settings doesn't resolve the issue. Using iTunes to restore iOS devices is part of standard isolation troubleshooting. Restoring your device will delete all data and content, including songs, videos, contacts, photos, and calendar information, and will restore all settings to their factory condition.
    Before restoring your iOS device, Apple recommends that you either sync with iTunes to transfer any purchases you have made, or back up new data (data acquired after your last sync). If you have movie rentals on the device, see iTunes Store movie rental usage rights in the United States before restoring.
    Follow these steps to restore your device:
         1. Verify that you are using the latest version of iTunes before attempting to update.
         2. Connect your device to your computer.
         3. Select your iPhone, iPad, or iPod touch when it appears in iTunes under Devices.
         4. Select the Summary tab.
         5. Select the Restore option.
         6. When prompted to back up your settings before restoring, select the Back Up
             option (see in the image below). If you have just backed up the device, it is not
             necessary to create another.
         7. Select the Restore option when iTunes prompts you (as long as you've backed up,
             you should not have to worry about restoring your iOS device).
         8. When the restore process has completed, the device restarts and displays the Apple
             logo while starting up:
               After a restore, the iOS device displays the "Connect to iTunes" screen. For updating
              to iOS 5 or later, follow the steps in the iOS Setup Assistant. For earlier versions of
              iOS, keep your device connected until the "Connect to iTunes" screen goes away or
              you see "iPhone is activated."
         9. The final step is to restore your device from a previous backup.
    If you can not restore your device then you will need to go to recovery mode.
    Placing your device into recovery mode:
    Follow these steps to place your iOS device into recovery mode. If your iOS device is already in recovery mode, you can proceed immediately to step 6.
         1. Disconnect the USB cable from the iPhone, iPad, or iPod touch, but leave the other end
             of the cable connected to your computer's USB port.
         2. Turn off the device: Press and hold the Sleep/Wake button for a few seconds until the
             red slider appears, then slide the slider. Wait for the device to turn off.
              If you cannot turn off the device using the slider, press and hold the Sleep/Wake
              and Home buttons at the same time. When the device turns off, release the Sleep/Wake
              and Home buttons.
         3. While pressing and holding the Home button, reconnect the USB cable to the device.
             The device should turn on. Note: If you see the screen pictured below, let the device
             charge for at least ten minutes to ensure that the battery has some charge, and then
             start with step 2 again.
         4. Continue holding the Home button until you see the "Connect to iTunes" screen.
             When this screen appears you can release the Home button.
         5. If necessary, open iTunes. You should see the following "recovery mode" alert:
         6. Use iTunes to restore the device.
    If you don't see the "Connect to iTunes" screen, try these steps again. If you see the "Connect to iTunes" screen but the device does not appear in iTunes, see this article and its related links.
    Additional Information:
    Note: When using recovery mode, you can only restore the device. All user content on the device will be erased, but if you had previously synced with iTunes on this computer, you can restore from a previous backup. See this article for more information.

  • I have a Mac notebook and it says it's connected to wifi, but when I try to connect to any search engine it does not.  What is causing it to not actually connect.  My pc connects no problem.

    It seems that all apple products used in my house at times will not connect to our wifi.  It's hit and miss.  It says I am connected, but when you try to connect to any search engine it does not.  I have disconnected and reconnected the power to the dsl provider and to our wifi units.  I have rebooted the computers.  I have reentered the password.  Still no connection.   We do not have connectivity issues with our PC products.  Anyone have any answers for me?

    Does the iOS device connect to other networks?
    Does the iOS device see the network?
    Any error messages?
    Do other devices now connect?
    Did the iOS device connect before?
    Try the following to rule out a software problem:                 
    - Reset the iOS device. Nothing will be lost
    Reset iOS device: Hold down the On/Off button and the Home button at the same time for at
    least ten seconds, until the Apple logo appears.
    - Power off and then back on your router
    .- Reset network settings: Settings>General>Reset>Reset Network Settings
    - iOS: Troubleshooting Wi-Fi networks and connections
    - Wi-Fi: Unable to connect to an 802.11n Wi-Fi network
    - iOS: Recommended settings for Wi-Fi routers and access points
    - Restore from backup. See:
    iOS: How to back up
    - Restore to factory settings/new iOS device.
    If still problem make an appointment at the Genius Bar of an Apple store since it appears you have a hardware problem.
    Apple Retail Store - Genius Bar

  • My ipod 2g says I am connected to wifi but when I go to the home I see no wifi bars and it will not let me use the internet, My ipod 2g says I am connected to wifi but when I go to the home I see no wifi bars and it will not let me use the internet

    Plzzzzz help

    Does the iPod connect to other networks?
    Do other devices now connect?
    Did the iPod connect before?
    Try:
    - Reset the iOS device. Nothing will be lost
    Reset iOS device: Hold down the On/Off button and the Home button at the same time for at
    least ten seconds, until the Apple logo appears.
    - Power off and then back on the router
    - Reset network settings: Settings>General>Reset>Reset Network Settings
    - iOS: Troubleshooting Wi-Fi networks and connections
    - iOS: Recommended settings for Wi-Fi routers and access points
    - Restore from backup. See:
    iOS: How to back up
    - Restore to factory settings/new iOS device.
    - Make an appointment at the Genius Bar of an Apple store.
    Apple Retail Store - Genius Bar

  • My iPad says I am connected to wifi, but the internet won't work. I have tried turning wifi on/off and also resetting the network settings. Help!

    The past two days my iPad mini has not been working with the wifi at my house. There is also and iPhone 5 and an iPad air that are working perfectly fine. I don't know what to do

    Try forgetting the network, reboot your iPad and then try joining the network again.
    Settings>WiFi>Your network name>Forget this network. Reboot the iPad by holding down on the sleep and home buttons at the same time for about 10-15 seconds until the Apple Logo appears - ignore the red slider if it appears on the screen - let go of the buttons. Let the iPad start up.
    Go back to Settings>WiFi>Your network name>Enter your password>Tap Join.
    If that doesn't work, reset network settings. Settings>General>Reset>Reset Network Settings. Reboot the iPad again. Go back to Settings>WiFi>Your network name>Enter your password>Tap join.

  • My iPad 1 says it's connected to wifi but safari says can't open page cause not connected to the internet

    Does anyone know why this is I've tried resetting but doesn't help?

    Are you on a home or open network? Sometimes when you're in a hotel, for example, you may be 'on' the net but not allowed to access it until you agree to their terms.

  • MacBook Air connects to WiFi but can't connect to internet for about 5 minutes

    I have a MacBook Air running Yosemite and whenever I wake it from sleep or turn it on it says it's connected to wifi, but it's usually about 5 minutes before anything will load.
    • Happens on multiple wifi networks
         • and doesn't happen to other devices on those networks
    • Been going on for ages (since Mavericks)
    • Diagnostics says nothing's wrong
    • Still happens on other users and in safe mode.
    Does this happen to anyone else / does anybody know a way around it?

    Hi jamang1999,
    For that specific issues where you are connected to the internet after waking your MacBook Air up from sleep and it is not connecting to the internet, then take a look at the article below to troubleshoot the issue further. There is a section called Symptom: After restarting or waking from sleep, my computer might not connect to the Internet and go through those troubleshooting steps to see if it continues afterwards. I know that the troubleshooting is for OS X lion and previous version of OS X but the troubleshooting is still relevant. If it does not work and are still experiencing issues, then you may need to contact Apple for additional support. 
    Wi-Fi: How to troubleshoot Wi-Fi connectivity
    https://support.apple.com/en-us/HT202222
    Take it easy,
    -Norm G.  

  • My iphone 4s is connected to wifi but it won't access the internet

    My iphone is running on iOS7. It says it's connected to wifi but I can't access the internet. Some apps work like mail and facebook but that's it. Everything else says theres no connectivity. When I turn it off and use 4g they work. I've tried everything from turning off the wifi to reset settings. I don't know what the problem is. Can anyone help?

    Welcome to Apple Support Communities
    Hold Sleep and Home buttons for 10 seconds until your device restarts, so you will be able to use the device again

  • My ipad is connected to wifi, but wont access any websites.  Help.

    My iPad says it is connected to WiFi, but it won't access any websites.

    Try a Restart.
    Press and hold the Sleep/Wake button for a few seconds until the red "slide to power off" slider appears, and then slide the slider. Press and hold the Sleep/Wake button until the Apple logo appears.
    Resetting your settings
    You can also try resetting all settings. Settings>General>Reset>Reset All Settings. You will have to enter all of your device settings again.... All of the settings in the settings app will have to be re-entered. You won't lose any data, but it takes time to enter all of the settings again.
    Resetting your device
    Press and hold the Sleep/Wake button and the Home button together for at least ten seconds, until the Apple logo appears. Apple recommends this only if you are unable to restart it.
    Or if this doesn't work and nobody else on the blog doesn't have a better idea you can contact Apple.
    Here is a link to their contacts with most of the information below.
    http://www.apple.com/contact/

Maybe you are looking for

  • Advice on how to format an external hard drive for a MacBook Air

    I have an external USB hard drive plugged into a 64GB MacBook Air. How should I format the hard drive so that when I run out of room on the small 64 GB SSD drive on the MacBook Air, it will start putting some iTunes or other files onto the external h

  • How to get the list of SAP Servers defined in xMII?

    Hi, We have a requirement to get the list of SAP Servers defined in xMII and show them in a html dropdown field? We know that we could achieve this by using a custom action block. Is there any way to get this list of SAP servers without using custom

  • How do I find and older version of instagram for iOS 6.1.6

    How do I find and older version of instagram for 4th generation touch iOS 6.1.6?

  • How to retrieve data in air application

    Hi All, I have problem with fetching the data from database. I don't know how to collect data. Like in .NET we have DataTable/Dataset for collecting data. How to collect data into adobe air.? I can INSERT,UPDATE and DELETE the data dynamically. But s

  • How do I install second party plugins?

    Curious as I did it in CS4, but CS5 is giving me trouble or I had a lapse. I wish to install Topaz Fusion express 64 bit, Wacom Intous tablet, photo matrix pro, and Nik Viviza. I thought I would start with the Topaz labs fusion express, I navigated t