IPod Touch 5 jitters after being connected to Bose Series III

iPod Touch 5 music jitters after being connected to Bose Series III

Reset the Bose device
- Reset the iOS device. Nothing will be lost
Reset iOS device: Hold down the On/Off button and the Home button at the same time for at
least ten seconds, until the Apple logo appears.
- Reset all settings      
Go to Settings > General > Reset and tap Reset All Settings.
All your preferences and settings are reset. Information (such as contacts and calendars) and media (such as songs and videos) aren’t affected.
- Restore from backup. See:                                 
iOS: How to back up           
- Restore to factory settings/new iOS device.

Similar Messages

  • Ipod disconnects immediately after being connected to computer

    Every time I plug my iPod into my computer it says "Connecting" then it says "Ejecting" and then "OK to disconnect"! WHY????? It does not show up in the sidebar in iTunes, and it does not show up in My Computer.
    I have plugged it into every USB port on my computer, none of them worked
    I have already updated iTunes.
    I have already put the iPod in disk mode.. that did NOTHING.
    I know it's not a problem with my USB ports, because other devices work JUST FINE in them
    I know it's not an issue with the USB cable because I plugged my iPod into another computer and my iPod did not disconnect right after being connected
    PLEASE help me get my iPod to work on this computer. And I don't want answers telling me to use the other computer. My Library is on THIS computer. Not only that, iTunes doesn't even work on the other computer.

    Reset the Bose device
    - Reset the iOS device. Nothing will be lost
    Reset iOS device: Hold down the On/Off button and the Home button at the same time for at
    least ten seconds, until the Apple logo appears.
    - Reset all settings      
    Go to Settings > General > Reset and tap Reset All Settings.
    All your preferences and settings are reset. Information (such as contacts and calendars) and media (such as songs and videos) aren’t affected.
    - Restore from backup. See:                                 
    iOS: How to back up           
    - Restore to factory settings/new iOS device.

  • HT1430 øw do I reset my iPod touch passcode after being locked out?

    iPod touch passcode has been forgotten.  How do we reset the passcode? We got locked out from so many wrong attempts.

    Place the iOS device in Recovery Mode and then connect to your computer and restore via iTunes. The iPod will be erased.
    iOS: Wrong passcode results in red disabled screen
    If recovery mode does not work try DFU mode.
      How to put iPod touch / iPhone into DFU mode « Karthik's scribblings

  • Ipod Touch suddenly stopped being connected to Wifi how do I fix?

    I got a Ipod Touch for Christmas and the Internet has worked great on it and now it just suddenly stopped connecting to the Wifi on my laptop and need help fixing. What can I do to get it up and running again? Thanks!

    - Also try resetting the iPod. Nothing will be lost
    Reset iPod touch:  Hold down the On/Off button and the Home button at the same time for at
    least ten seconds, until the Apple logo appears.
    - Also, power off and then back on the router.
    From your wording, are you using the laptop as a router? Is it working OK?
    What happens whenyu try to connect to the network? Error messages like can't join?

  • My ipod touch says "activation required, connect to itunes" i restore it on my itunes and it seems to be working, after i tried connecting to my wifi but no luck, i reset it and the same thing happens all over again. Help!

    my ipod touch says "activation required, Connect to itunes" i restored it with on my itunes and it seems to be working again, after i tried connecting to my wifi with no luck i reset it, and again it pops back "activation required, connect to itunes" i restored again, its a non ending cycle, and it makes no sense having my ipod and i cannot connect to the internet with it, can someone please help with this issue?

    Maybe here:
    Restore loop (being prompted to restore again after a restore successfully completes)
    Troubleshoot your USB connection. If the issue persists, out-of-date or incorrectly configured third-party security software may be causing this issue. Please follow Troubleshooting security software issues. .
    Next would be to make an appointment at the Genius Bar of an Apple store.

  • IPod Touch 4th gen  trouble connecting to my Win-Vista 64bit computer via USB.

    Hi,
    I seem to have an issue with my iPod Touch 4G. Ever since upgrading to iOS5. 
    The iPod Touch has had issues connecting, via direct USB, to my Windows Vista 64 bit computer.  When I connect it, via USB, the computer will report the iPod Touch 4G as an "Unrecognized Device."  This prevents me from using the USB to sync the iPod or charge it via the computer's USB connection. 
    My work around is to turn off the iPod (via red slide bar method) then connect it to the USB.  At this point, it in it will automatically re-start the iPod and then it will recognize and sync or charge.  I can also connect it have it report as an "Unrecognized Device" leave it connected, turn it off(red slide bar) and turn it back on and it will also connect charge and sync. 
    The problem is that I must turn it off every time I want to connect it.  I can sync via wi-fi (but this causes issues with music that others have shared with me-keeps asking for their i-Tunes account) (happened after I "re-set" the I-Pod).  I needed to hard sync with the computer to make all the rights work out.
    This same USB cable and computer works just fine with my other iPods (Touch 3G, Classic) and my iPhone 4S.  Only problem device is the Touch 4G.  The problematic iPod and same USB cable works without issue on other computers (i.e.:  don't have to turn it off and then plug it in).
    I've followed the apple instructions and sequence to remove I-Tunes and a bunch of other related software and then reinstall it.  I've reset my iPod. Nothing corrects this issue with this particular iPod.  I've changed USB ports, tried other USB cables nothing changes the fact that I have to turn off and back on the iPod Touch 4G each time before I can get it to be properly recognized by the computer and thus charge or be recognized by iTunes.
    This only started to happen to the iPod Touch 4G after I upgraded it from iOS4 to iOS5.  I also have iOS5 on my iPhone 4S - with no issues.  My other iPod Touch 3G is using iOS4.  It connects and syncs fine.
    I've figured out a work around but, does anyone know how to fix this issue?  Thanks

    Hi,
    Yes, I have restored from Backup via i-Cloud. I've restored the iPod to factory settings.  It seem like there is a driver issue.  I installed iOS 5.01 and updated iTunes to 10.5.3.3 at about the same time.  Win-Vista64, iTunes and iPod are all up to date.  Apple Genius, at local Apple store was also perplexed.  He suggested I ask the community.  So, here I am.
    It is strange that I can connect to other computers.  But, the other computers have Win 7.  Could this be a Vista64 driver issue?

  • My iPod touch isn't being recognized by my pc. The lock button on it won't work due to water damage, and a friend of mine fixed the problem by restoring it on his computer. How do I restore it without the lock button?

    My iPod touch isn't being recognized by my pc. The lock button on it won't work due to water damage, and a friend of mine fixed the problem by restoring it on his computer. How do I restore it without the lock button?

    first try:
    iOS: Device not recognized in iTunes for Windows
    next
    Try:
    - iOS: Not responding or does not turn on
    - Also try DFU mode after try recovery mode
    How to put iPod touch / iPhone into DFU mode « Karthik's scribblings
    - If not successful and you can't fully turn the iOS device fully off, let the battery fully drain. After charging for an least an hour try the above again.
    - If still not successful that usually indicates a hardware problem and an appointment at the Genius Bar of an Apple store is in order.

  • My 4th generation ipod touch is not being recognized on my computer ?

    My 4th generation ipod touch is not being recognized on my computer what do i do ?

    iOS: Device not recognized in iTunes for Mac OS X
    or
    iOS: Device not recognized in iTunes for Windows
    - I would start with
    Removing and Reinstalling iTunes, QuickTime, and other software components for Windows XP
    or               
    Removing and reinstalling iTunes and other software components for Windows Vista, Windows 7, or Windows 8
    However, after your remove the Apple software components also remove the iCloud Control Panel via Windows Programs and Features app in the Window Control Panel. Then reinstall all the Apple software components
    - New cable and different USB port
    - Run this and see if the results help with determine the cause
    iTunes for Windows: Device Sync Tests
    - Try on another computer to help determine if computer or iPod problem

  • New iPod Touch 4th gen. cannot connect to home wi-fi network

    When I launch wi-fi on my new iPod Touch 4th gen. my home network's name is displayed, but after entering my password the iPod is unable to connect - the wheel to the left of the network name just keeps spinning.   The network still functions properly for all my other devices (MacBook, 2nd gen. iPod Touch, wireless printer and my wife's PC) and the new iPod Touch did connect to the network in the Apple Store when I visited yesterday.   I know the password I enetered for my home network is correct because I've checked it in my keychain, and also the iPod did not inform me that it was the wrong password for that network - as it does if I enter another password.
    I have followed the advice given to others - unplugging the Time Capsule and leaving it for 5 minutes, checking that all my software and firmware is up to date, 'forgetting' the network on my new iPod then searching for it again, and have completely restored the iPod - but it still cannot connect to my network.   If my network is functioning properly, and my new iPod was capable of joining the Apple Store's network yesterday, and I am sure that I am entering the correct password, it seems to me that my problem must be due to some network setting that is refusing to allow a new device to connect.   I can't find where that setting might be - can anyone advise?

    depending on what router but hopefully all routers came to this default address....
    192.168.1.1/Wireless_MAC.asp
    from
    >Setup of the Basic Setup you goto
    >Wireless
    >WirelessMacFilter
    also had an idea when i wanna make sure im typing the right one, i would do is tap each letter/# by 1, as in,
    (e.q.)
    here's my ipod 4 and my ipod 2, the pswd is 123456
    ipod 4, i press 1
    ipod 2, i press 1
    ipod 4, i press 2
    ipod 2, i press 2
    and so on till i reach both of them to 6 (1by1) to make sure i get it in there right. saw this on another wall it might depends on what channel your using, but i dont rly think that matters bc i have mine on auto and nvr had a problem.
    i would do this even thou it may sound crazy to others....if i were you this is what i would do
    on your ipod 2Gen
    >Safari
    >address to 192.168.1.1/WL_WPATable.asp
    -(wireless security settings for passcode)
    >tap the box for the password, whatever ur security is i would copy
    -IF WEP
    -copy phrase key and Key 1
    -IF WPA
    -copy phrase key
    >open Notepad
    >under iCloud account Notepad
    >Paste the Key
    >either on your pc/mac or your 2nd Gen, go back to
    >192.168.1.1/WL_WPATable.asp
    >change your Security Mode to Disable
    >goto your 4 Gen iPod Touch
    >goto settings and connect to it, if pswd is still in it then tap forget this network and reconnect to it
    -once connected and got IP adresses
    >goto Notpad under iCloud
    -you should have obtained your recent icloud msgs included the key you pasted
    -once obtained
    >gobk to pc/mac or ipod 2nd gen and re enabled the security and re-paste the key in
    -once router adjusted try to connect to it
    >1st do your 2nd gen and forget this network reconnect to it and repaste the key
    >2nd goto ur 4rth gen from your notes, highlight the key in ur notpad and tap copy and forget this network reconnect to it and paste the key.
    this should work bc i did it myself when i couldnt get connected bc thats almost the same steps i did.
    somtimes i put my name up on here. remeber these names we put as our nickname doesnt mean its our real name or anything like that,
    ~Anthony

  • HT1335 My Ipod touch is not being recognized on my PC as a usb device.

    My Ipod touch is not being recognized on my PC as a usb device.

    Hey MOIMC,
    Sorry to hear your computer isn't recognizing your iPod Touch when you plug it in. I was able to find two articles that might help you out:
    iOS: Device not recognized in iTunes for Windows
    http://support.apple.com/kb/TS1538
    and
    iPod not recognized when connected to Windows laptop over USB
    http://support.apple.com/kb/TS1401
    Hope this helps,
    David

  • Someone stolen my ipod, Is't possible to know where is my iPod touch if the person connect Internet with?

    Someone stolen my ipod, Is't possible to know where is my iPod touch if the person connect Internet with?

    What To Do If Your iDevice Is Lost Or Stolen
    If your iPhone, iPod, iPod Touch, or iPad is lost or stolen what do you do? There are things you should do in advance - before you lose it or it's stolen - and some things to do after the fact. Here are some suggestions:
    This link, Re: Help! I misplaced / lost my iPhone 5 today morning in delta Chelsea hotel downtown an I am not able to track it. Please help!, has some good advice regarding your options when your iDevice is lost or stolen.
      1. Reporting a lost or stolen Apple product
      2. Find my lost iPod Touch
      3. AT&T. Sprint, and Verizon can block stolen phones/tablets
      4. What-To-Do-When-Iphone-Is-Stolen
      5. What to do if your iOS device is lost or stolen
      6. 6 Ways to Track and Recover Your Lost/Stolen iPhone
      7. Find My iPhone
    It pays to be proactive by following the advice on using Find My Phone before you lose your device:
      1. Find My iPhone
      2. Setup your iDevice on iCloud
      3. OS X Lion/Mountain Lion- About Find My Mac
      4. How To Set Up Free Find Your iPhone (Even on Unsupported Devices)

  • IPod Touch 2G crashes while connecting to WiFi

    After dropping my iPod Touch 2G 8GB badly on the pavement, I cracked my LCD and touch screen pretty badly.
    I ordered an LCD and touch screen on Amazon and replaced the parts on my iPod Touch. I got my iPod Touch able to turn on and fully function except that the speakers started making static noises. I'm guessing that I blew the speakers when I dropped it. The earphone jack does not work either, unfortunately.
    However, this is not my main concern.
    Whenever I try to connect to my WiFi, my iPod Touch crashes after I put in a couple of the characters for my password. Everything else works fine as far as I'm concerned, but my iPod always reboots when I try to put in my password for the internet. It's rather frustrating, but if anybody has any suggestions or thoughts as to why my iPod is doing this, it would be greatly appreciated.
    Thanks,
    Jin

    There seems to have more broken than just the screen.
    Bring it to the Apple Store and see what other options you have.

  • HT1212 how do I get my ipod touch unlocked from being disabled

    How do I get my Ipod touch unlocked from being disabled

    Follow the instructions here:
    Forgotten Passcode or device disabled after entering wrong passcode

  • TS2446 my ipod touch locked after several attempts with the wrong password. how to i reset?

    my ipod touch locked after several attempts with the wrong password. how do i reset the password.

    If it's showing the disabled screen due to too many incorrect passcode attempts then you will need to connect it to the computer that you normally sync to and you should then be able to reset the iPod and restore/re-sync your content to it (http://support.apple.com/kb/HT1212) - you may need to put the iPod into recovery mode in order to be able to reset it : http://support.apple.com/kb/ht1808
    If you do it via a different computer then :
    If you restore on a different computer that was never synced with the device, you will be able to unlock the device for use and remove the passcode, but your data will not be present.

  • HT4623 my ipod touch will no longer connect to my laptop because my ipod is not up to date, but it won't find a newer software. what should I do?

    my ipod touch will no longer connect to my laptop because my ipod is not up to date, but it won't find a newer software. what should I do?

    the computer is a macbook pro, mac os x 10.6.08 and the ipod touch is ios 6.0.
    the problem is that just updated the itunes on the computer and now the ipod won't connect because apparently the itunes on the ipod is not up to date but the iod is telling me that is is up to date, so i can't do a software update.

Maybe you are looking for

  • Time Capsule disk access SLOW!   2TB - Dual band

    I have a Time Capsule (2TB, Dual Band, Firmare at 7.4.2) Its been working like a dream, backing up 3 Macs for the last 8 months. I also use it for connecting two or three other disks via USB and then making those accessible over the LAN, and there is

  • What is best practice for installing husband/wife iPhones on one iTunes account?

    Is there a way to install two iPhones (or iPads for that matter) on one iTunes account in order to share apps, music, books, HOWEVER, keep contacts, calendar events, reminders separate? Goal: I want to have my iPad and iPhone and my wife's iPhone on

  • How to change the background color of a button when the button is emphasized

    Hi, I have a button that is in the "emphasized" state, I realized there is a default color "light blue" when the button is emphasized. is there any way I can change this default color? so if mu button goes to emphasized state I can control which colo

  • Client reconnection to conventional cluster taking about 9 minutes

    Hi, I've set up a 3 node OpenMq (4.4) conventional cluster and am having trouble with client reconnections when I simulate a halt on a node. I have two threads within the same process, sending to a pre-configured destination and replying using a temp

  • Recordset Structure value

    Hi ! I need to enter a value for the number of records in the Recordset Structure in the Content Conversion Parameters of the File Adapter. The records should be atleast one with a possibility of more than one records ....... in other words - one or