IPod Touch Is Going White & Wont Restore

I am having severe problems with my ipod touch, this is my second ipod and it is doing the same thing the other did.
It will turn on fine, and stuff after i do a soft restart and it will work, till it goes dead then i will plug it in and the screen will go white and it will not work any more, and when i try to reset it to factory settings it will not reset. It freezes either with a black or white screen...and it is very annoying, i am out of warranty, and can not afford another one, what should i do? please help! no sarcastic answers please!!!
Also it is saying trying to restore and it says then that a itunes internal error occured..and now all it has on it, if it turns on is a apple logo with a usb cord put on it to connect to my computer..
Message was edited by: rissabaybee2010

Welcome to the discussions,
Make sure your ipod is charged using the adapter for at least 10 min and try to connect in recovery mode to restore: http://support.apple.com/kb/HT1808

Similar Messages

  • My ipod touch 5 generation 16gb wont restore on itunes and sometimes it says that an error has accord (4013)

    my ipod touch 5 generation 16gb wont restore on itunes and sometimes it says that an error has accord (4013)

    Check USB connections
    If there’s an issue with the USB port, cable, dock, or hub, or if the device becomes disconnected during restore, try troubleshooting the USB connection, then troubleshooting your security software.
    Common errors: 13, 14, 1600-1629, 1643-1650, 2000-2009, 4000, 4005, 4013, 4014, 4016, “invalid response”, and being prompted to restore again after a restore completes.
    To narrow down the issue, you can also change up your hardware:
    Use another USB cable.
    Plug your cable into a different USB port on your computer.
    Try a different dock connector (or no dock).
    Add (or remove) a USB hub between your device and computer.
    Connect your computer directly to your Internet source, with no routers, hubs, or switches.
    If you see your error after changing your USB connections, continue to the next section to troubleshoot your hardware.
    Check for hardware issues
    Try to restore your iOS device two more times while connected with a cable, computer, and network you know are good. Also, confirm your security software and settings are allowing communication between your device and update servers. If you still see the alert when you update or restore, contact Apple support.
    Common errors: 1, 10-47, 1002, 1011, 1012, 1014, 1000-1020.

  • My ipod touch 4th gen 8gb wont restore please help me because there is nothing else i can do

    my 4th gen 8gb ipod touch wont restore, i have disabled my security and tried all of the online steps and still nothing. i have repeated it many times but still it wont restore and keeps coming up with a 1611 error please can anyone help?????

    You may well have a hardware problem (i.e., warranty).
    http://support.apple.com/kb/TS3694#error1611
    If the hyperlink doesn't work, try again.  There are problems at the Apple web site.

  • I downloaded version 4.3.2 for my ipod touch and now it wont restore and doesnt register

    i downloaded the newest version of itunes on my laptop and now my ipod wont restore or even register on my computer and itunes gives me an error message but if i hook it up to my wifes desktop it will restore the ipod and wen i go to hook it up to my laptop to put music on it, it wont register and has the connect to itunes on the screen what do i do now?

    I do not understand how the two can be related.  Have you tried verifying/repairing the disk on your MacBook?

  • Ipod touch display goes white

    Sometimes, while accidently putting pressure on certain parts of my ipod touch, the screen blanks out, like the display was disconnected somehow. This is temporarily solved when I press down on the space above the screen, but after a while it happens again. Any suggestions?

    Yes, it the iPod is deffective (it sounds like it is) and the iPod has not been abused.  Make an appointment at the Genius Bar of an Aplle store and find out.  If defective and not abused you should walk out with a replacement.

  • What do i do if my ipod touch screen went white and wont turn off?

    what do i do if my ipod touch screen went white and wont turn off?

    - Try a reset.
    Reset iPod touch:  Hold down the On/Off button and the Home button at the same time for at
    least ten seconds, until the Apple logo appears.
    - Connect to computer and restore if it appearsin iTunes.
    - If screen still white let the battery fully drain. After charging for an hour repeat the above.

  • I forgot my ipod touch 5 passcode, itunes wont let me restore

    Okay so heres the problem: i have forgotten my password to my 5th gen. Ipod touch. I have tried restoring it, didn't work because of the find my ipod thing. So i put it in DFU mode and itunes told me that it could take up to 60 hours to update and restore. My mother kinda flipped at the idea, but said okay go with it. Half an hour later the whole thing was interrupted  and little box came up and said it timed out. I really need help here please! I'm using my old ipod

    Try disabling the computer's antivirus and firewall.
    - Next try the manual install method of:
    iDevice Troubleshooting 101 :: iPhone, iPad, iPod touch
    Place the iPod in recovery mode after the firmware download is complete and then restore using the instructions in the article. Sometimes recovery mode timeouts and returns to disabled before the firmware download is complete.
    - Then try on another computer

  • Everytime my iPod touch turns on, it wont let me type in my passcode.

    Everytime i turn on my iPod touch, it goes to the passcode screen and wont let me type in my passcode. then it just keeps restarting the enter passcode screen. what do i do?

    Place the iOS device in Recovery Mode and then connect to your computer and restore via iTunes. The iPod will be erased.
    iOS: Wrong passcode results in red disabled screen
    If recovery mode does not work try DFU mode.
    How to put iPod touch / iPhone into DFU mode « Karthik's scribblings

  • HT201412 My Ipod touch is flashing white how do i fix it?

    It sometimes fixes when its on charge but it is moastly white . The charger thing doesnt work anymore and this is getting on my nerves as i got it about 7months ago for £139.00 of off amazon! How can i make it stop flashing white and can only make out a few words! If this helps i have 1 little scratch on my screen but i dont think that has anything to do with it as my sisters has loads of scratches and doesnt flash white HELP ME PLEASE

    Sorry... But  the BOLD and the PURPLE are impossible to read...
    You asked in the Header...
    ' My iPod touch is flashing white how do i fix it? '
    Suggestions:
    Try a Reset...
    Reset  ( No Data will be Lost )
    Press and hold the Sleep/Wake button and the Home button at the same time for at least ten seconds, until the Apple logo appears. Release the Buttons.
    http://support.apple.com/kb/ht1430
    If necessary...
    Connect to iTunes on the computer you usually Sync with and “ Restore “...
    http://support.apple.com/kb/HT1414

  • Ipod touch 4th generation will not restore

         My ipod touch 4th generation will not restore. It begain with a random problem with the device. I tried to open a application but the application would blink a few times then would not open. This was so for ALL of the applications. I then powered of my device to try and reboot it. The Apple logo will apear for about 5 seconds but then the sreen will go black and the Apple logo will apear again. I tried to reboot several times and it did not work. I then connected my device to my computer but it would not appear in Itunes. The only way for the device to appear was for me to put it into DFU mode by holding down the home and power button for 10 seconds. My Itouch would have the connect to Itunes on it. It was then reconized by Itunes. Itunes message appeared telling me that i need to restore my Ipod. I tried restoring the Ipod, but after the update downloaded a error would appear while it was going through the restoration proccess.
         My Ipod is under the one year warrenty and i also had purchased an extended two year warrenty for my Ipod. I do not know what i should do.

    ok i will my friend has my ipod right now but If it doesn't still work ill get the error number tomorrow.

  • Got my daughter an ipod touch 4th and it wont dothe back up from itunes? I bought my other daughter an iphone 4 and its doing the same thing. Both are locking up itunes too.

    Got my daughter an ipod touch 4th and it wont dothe back up from itunes? I bought my other daughter an iphone 4 and its doing the same thing. Both are locking up itunes too. I tried the deactivate/activate that was suggested it still didnt work. I took the ipod to a friend and hooked to her laptop and it synced fine but now trying to sync on mine it wont do it and it has the backup encryption on but no passwords will unlock it. itunes will reccognize the ipod and the iphone but while going thru the sync steps they both get to step 2 then lock up itunes and then says its syncing but will never stop. I am very frustrated and am regretting buying products from Apple.

    It seems to be a glitch or bug. Its been officially acknowledged and addressed by Apple. There is no resolution other than waiting for a few days.   The Kb article by Apple states it will fix itself on January 7.
    http://support.apple.com/kb/TS4510
    Symptoms
    After January 1st, 2013, Do Not Disturb mode stays on past its scheduled end time.
    Resolution
    Do Not Disturb scheduling feature will resume normal functionality after January 7, 2013. Before this date, you should manually turn the Do Not Disturb feature on or off.
    To turn off the scheduling feature, tap Settings > Notifications > Do Not Disturb and switch Scheduled to Off.

  • I dropped my ipod touch and now it wont charge

    I dropped my ipod touch and now it wont charge. When I plug it in to charge it just keeps going off and on.

    Not Charge
    - See:      
    iPod touch: Hardware troubleshooting
    - Try another cable. Some 5G iPods were shipped with Lightning cable that were either initially defective or failed after short use.
    - Try another charging source
    - Inspect the dock connector on the iPod for bent or missing contacts, foreign material, corroded contacts, broken, missing or cracked plastic.
    - Make an appointment at the Genius Bar of an Apple store.
    Apple Retail Store - Genius Bar      

  • Is the iPod Touch always going to backup?

    Since updating to 2.0, iTunes wants to backup my iPod every time I connect. Is my iPod Touch always going to do a Backup during the sync process or is there a setting to adjust this?

    This is what I do.
    I created a TextEdit file and stored it on my desktop, It is two lines (commands) separated by a return. You can copy the two commands from this message to your clipboard. The two commands are:
    defaults write com.apple.iTunes DeviceBackupsDisabled -bool true
    defaults write com.apple.iTunes DeviceBackupsDisabled -bool false
    When used in the Mac OSX application Terminal, the first line is used to turn off backups. The second turns them back on.
    Once you have the TextEdit file saved in the location that you want, do the following steps.
    1. Open your TextEdit file
    2. Highlight the command you want. Use only one. I triple click the text with my Logitech mouse.
    3. Select Edit>Copy
    4. Open the application Terminal
    5. Select Edit>Paste (Hit return if you don't get a new prompt.)
    6. Terminal does not confirm the result of the command. You just get the same prompt as before.
    7. Type exit. Terminal responds "Process Completed"
    8. Quit Terminal and TextEdit You are done and ready to sync.
    This takes about thirty seconds compared to the backup which in my case takes hours.
    PLEASE NOTE
    I use my Administrator account to do this. Never tried it with a Standard account.
    If you choose to disable backups, any data saved in iPod touch applications will be lost if you have to do a restore.
    I tested the no backup command a few minutes ago and it worked syncing my iTouch 1G to my iMac.
    I posted this step by step incase you have never used Terminal. My apologies to the Unix geeks.
    Use at your own risk.
    I

  • Ipod Touch 5th gen stuck in restore mode

    My Ipod Touch 5th gen stuck in restore loop i keep clicking restore and i just keeps downloading the ipod software update, and i wont restore it just keeps saying that a ipod was found in restore mode..... Can someone please help

    The same thing happened to me, while restoring my iPod Touch Generation 5.  I don't know if you are still caught in the same loop but this worked for me.  I am using a MacBook Air running Mountain Lion version 10.8.2.  iTunes is at version 11.0.
    After running through the published Restore procedure without any success I found the Software Update file had downloaded as:
    "/Users/my_home_directory/Library/iTunes/iPod Software Updates/iPod5,1_6.0.1_10A523_Restore.ipsw"
    The ~/Library directory is invisible on my machine, more than likely a design standard.  I used a terminal to first locate the file and then to copy the file to a readable location, my Desktop.
    My iPod was still stuck in Recovery Mode so I plugged it in.  iTunes was already running and identified the Recovery Mode iPod, prompting me to Restore it.  I clicked OK. 
    I held the option key while clicking Restore.  This opened a navitation window that enabled me to select the Software Update .ipsw file I had copied to my Desktop.  The Restore process then ran without any failure and the iPod is now running again. 
    This is not a formal solution as far as I can tell, nor have I verified the procedure across multiple iPods, multiple scenarios, etc.  I just wanted to share it as an "at-your-own-risk" alternative you might want to try. 
    Good luck, cupcakequeen83.

  • HT1430 th screen on my ipod touch went all white and I already tried restarting it but still doesnt work

    the screen for my ipod touch went all white and I already tried to restarted but still doesnt work. What can i do?

    Let the battery drain dead, recharge it and test. If it still does not work, restore.
    Troubleshooting 101
    Some topics covered
    -Basic troubleshooting steps
    -Hard reset instructions
    -Manual restore instructions
    -Hardware troubleshooting
    -Preventive Maintenance
    -Anti-theft & recovery tips
    -Battery-saving tips
    -Repair options
    -Contacting Apple
    17" 2.2GHz i7 Quad-Core MacBook Pro  8G RAM  750G HD + OCZ Vertex 3 SSD Boot HD 
    Got problems with your Apple iDevice-like iPhone, iPad or iPod touch? Try Troubleshooting 101
     In Memory of Steve Jobs 

Maybe you are looking for

  • K9N Platinum and OCZ2P8001GK

    Hi. I bought 2 OCZ PC2-6400 512MB DIMM (OCZ2P8001GK) and I am thinking of buying the MSI K9N Platinum (non-SLI) board to run with AMD Athlon X2 3800+. Will it be any compatibility problems running the system with those memory modules? [Running at sto

  • Problems fading sound clips in and out in iM 6 HD

    I have imported a MP3 music clip into my movie timeline. It plays fine on playback.But when I share with iDVD, and test it on my computer or a DVD player the fade in/out on that specific spot is very abrupt and erratic and sounds quite terrible. I ha

  • OWB on Oracle 10G Release 2

    Dear all, I planned to use an Oracle 10G Release 2 database for a new OWB project. Research on the web just told me that this new version of the database does not support OWB, because of a check for DBA privileges. The website advises to either use a

  • Stored Scripts are gone after upgrade from 1.5 to 2.0

    Upgraded from 1.5 to 2.0 and there are now problems with the "SQL Scripts" in SQL Workshop: 1. SQL scripts appear to have gone missing - over 200 from one workspace. I checked the WWV_FLOW_FILE_OBJECTS$ table in 2.0 and they are not in there. 2. All

  • Generating dynamic column in planning layout

    Hi Guys, I am new to BPS.. My task is user inputs calendar year thru variable, based on the year it has generate dynamic columns as month of the year entered by the user. Dnt know i am right or wrong based on the sdn threads. i think i have to create