IPod Touch Won't Recognize USB Cables

My 4th gen iPod Touch no longer recognizes my USB cables. They won't work through my computers and they won't work through a wall charger. My iPod charges fine through my JBL Sound Stage, it's just a problem with the cables. If I plug either cable into my iPod, nothing happens. No beeps, no messages, no charging screen, nothing.
I think I can pinpoint the problem until shortly after I purchased a spare cable, but that may very well be a coincidence. I've been using a third party wall charger, so that could be an issue as well- but it has never been a problem until after I purchased the new cable (can cables "burn out"?). I'd reset my iPod, but I need a cable to do that. So far I've just been charging via my JBL Sound Stage and syncing over WiFi.

If you have tried multiple computers and multiple USB sync cables, that definitely points to a hardware issue with your iPod Touch.  Have you check the dock connector port for any signs of damage or debris that could be blocking or preventing the connection?  Take a can of compressed air and trying blowing it out and using a Q-tip or similar to clean the contacts.
You'll likely need to have the iPod serviced or replaced.  If still under warranty, take it into your local Apple store and see what they can do for you.
B-rock

Similar Messages

  • Please help!  My IPod touch won't recognize the digits I enter for my password and won't put a "dot" in the password squares.  It also speaks the numbers I enter, very, very fast!

    Please help!  My IPod touch won't recognize the digits I enter for my password and won't put a "dot" in the password squares.  It also speaks the numbers very, very fast.  Can anyone help?

    Sounds like some accessibility features have been turned on. See this article for instructions on turning them off.
    http://support.apple.com/kb/HT3577
    B-rock

  • IPod Touch won't recognize Sonos

    I am hung up in the Sonos Ipod Touch setup process. I installed Sonos client on my ipod touch. When it searches for a system to join and I press Mute+Vol Up on my zoneplayers, the ipod does not recognize my Sonos whatsoever.
    Here is my setup:
    Cable Internet to
    Motorola Cable Modem to
    Linksys Wired Router to
    Sonos
    I plugged an Apple Airport Express into the Linksys Wired router and the internet works fine on my ipod touch. Again, doesn't recognize Sonos.
    I called Sonos support on Friday and got what sounds like good advice: the Apple Airport Express needs to be configured as a bridge. I have searched forum after forum (many non-Sonos) and I just can't figure out how to make this work.
    My configuration is not that unusual -- please help me!!! The main reason I got an ipod touch was to serve as another Sonos remote!
    Thanks in advance

    Personally, I would retire the Linksys router and use your Airport Express as your primary router. Then if you need additional ethernet ports, you can setup your Linksys router as a bridge and use it as a four port switch (or you can just buy a 4 port switch really cheap).

  • My iPod touch won't recognize my touch. It won't read or accept my finger. Ive tried to turn it off but it won't help it and doesn't fix it. Can someone please help me?

    Please help me.
    I wanna buy a new screen but I don't wanna buy it and it be a waste of money so can someone please help me?

    Try the following:
    - A reset. Nothing is lost
    Reset iPod touch: Hold down the On/Off button and the Home button at the same time for at
    least ten seconds, until the Apple logo appears.
    - Restore from backup
    - Restore to factory settings/new iPod.
    If you still have the problem that indicates a hardware problem and an appointment at the Genius Bar of an Apple store is in order

  • My iPod touch won't recognize in itunes..

    I have Version 4.1 (it's an older iPod touch). Whenever I plug in my iPod to the computer, it doesn't even pop up in the device manager list in iTunes.
       Any ideas?

    Try here:
    iOS: Not responding or does not turn on
    Next make an appointment at the Genius Bar of an Apple store.

  • IPod touch won't recognize new security questions

    I set my daughters iPod up using my email address.  She received an iTunes gift card which she wanted to use.  We redeemed it per the instructions on the back, and then she went to rent a movie.  At this point the device stated that since nothing had been downloaded on the device, I had to enter my Apple ID and password.  THEN, it asked me to answer 2 security questions, one of which I obviously did not know the answer to, or perhaps typed wrong when I was entering it.
    I followed the instructions for resetting the security questions, and the one question it was asking me "Which is the least favorite car you have owned?" was not even one of the choices to BE changed.  I went ahead and changed all 3 of the questions and saved the changes.  Unfortunately, when I go back into iTunes on her iPod, it is still asking me the same 2 questions that it was prior to me changing them.
    So, essentially, because I don't know what my least favorite car has ever been, my daughter will never be able to download anything onto her iPod touch.
    HELP!

    Maybe this previous discussion will help:
    HT1491 How do i get the security...: Apple Support Communities

  • IPod touch won't recognize my password

    All of a sudden, when I turn on my iPod touch & attempt to put in my password, I'm told the p/w is incorrect & it says to try again in 15 minutes.  I haven't changed the p/w since I got it, so what's going on? 

    Connect the iOS device to your computer and restore via iTunes. Place the iPod in Recovery Mode if necessary to allow the restore.
    If recovery mode does not work try DFU mode.
    How to put iPod touch / iPhone into DFU mode « Karthik's scribblings
    For how to restore:
    iTunes: Backing up, updating, and restoring iOS software
    To restore from backup see:
    iOS: How to back up
    If you restore from iCloud backup the apps will be automatically downloaded. If you restore from iTunes backup the apps and music have to be in the iTunes library since synced media like apps and music are not included in the iPod backup that iTunes makes.
    You can redownload iTuns purchases by:
    Downloading past purchases from the App Store, iBookstore, and iTunes Store

  • My computer was rebuilt and now my ipod touch won't recognize it as an authorised devise what do I do

    I would like to know how to authorize my computer now that it has been rebuilt? My "old computer" no longer exists, as this technicly is my "old computer" just new insides. I need to be able to manage my devises that are linked to my i touch, so that I can sinc it. It's been almost a full year since it's been sinced, and I don't want to lose my stuff!

    I am not clear as to your problem. Maybe:
    Syncing to a "New" Computer or replacing a "crashed" Hard Drive: Apple Support Communities
    or maybe:
    iOS: Device not recognized in iTunes for Windows
    I would start with               
    Removing and Reinstalling iTunes, QuickTime, and other software components for Windows XP
    or               
    Removing and reinstalling iTunes and other software components for Windows Vista, Windows 7, or Windows 8
    New cable and different USB port?
    Runs this and see if the results help with determine the cause
    iTunes for Windows: Device Sync Tests
    Try on another computer to help determine if computer or iPod problem

  • My 4th gen iPod touch won't recognize the remote feature on earbuds other than Apple earpods - anyone else had this issue?

    Apple earpods don't fit my ears well, so I bought a pair of Sony earbuds a few months ago. When they came, I noted that I could turn volume up and down, but the remote portion didn't work - couldn't pause or skip music. They weren't the highest quality so I assumed it was a fluke.
    I just got a new pair of earbuds and same issue! The volume works but the remote does nothing. I tried to use my boyfriend's Apple earpods with my touch and the remote works fine. Also, the new earbuds I got work, remote and all, on his 4th gen Nano.
    I can't seem to find anything online about why these earbuds that are supposed to be compatible wouldn't be working. I've cleaned out the audio jack so it's not a lint issue, plus it really does work just fine with Apple earpods, only alternatives don't work. And again, I can hear fine and the volume can be controlled but the remote to pause and play and skip isn't recognized at all.
    Any suggestions would be appreciated!

    So just in case anyone else ever runs into this...
    I solved the issue and it was that between the plug of the new earbuds being slightly thicker than the Apple earpods, and the width of the case that I was using for my iPod, there wasn't a connection being made to activate the remote function.
    I took off the case and now the earbuds work exactly as they should!

  • My ipod touch is showing a usb pointing to the itunes logo on the screen and nothing else.  It won't switch on beyond that.  Please help!

    my ipod touch is showing a usb pointing to the itunes logo on the screen and nothing else.  It won't switch on beyond that.  Please help!

    Sounds like your iPod is in restore mode. Connect it to iTunes. iTunes will pop a little message up saying that your iPod is in restore mode and asking you if you want to restore it, click yes. Your iPod will restore to factory settings and you will be given the chance to restore from a backup. You can do this or set it up as a new iPod.
    Here is Apple's page on restoring your iPod.
    http://support.apple.com/kb/ht1414
    Hope that helps.

  • HT201210 My Ipod has itunes icon and usb cable icons on its face but won't respond or restore how do I get it to do something?

    I tried to update the new ipod sofware and my ipod has a itunes and usb cable picture on its face, but after hours it will not do anything.  I tried to restore and it won't even do that. 
    What do I do?

    If you hit restore, you lose all your previous information.
    All I was just trying to do is update my Ipod!!
    Now its all messed up. Should have left it the way it was!

  • TS3716 Help! My iPod touch won't connect to itunes, but it shows usb connecting to itunes and it doesn't connect to itunes.

        I was updating IOS 6.1.3, my iPod touch 5th generation crashed and it showed The image: USB connecting to iTunes LOGO. I waited along time but nothing happeded. Is it in recovery mode or something? I don't know. Please help. Even I plugged in my USB to my pc it doesn't work! It shows nothing but in my iPod touch it shows the USB connecting to ITUNES.

    Hello Luke Lukas,
    Thanks for using Apple Support Communities.
    Stops responding, showing the Apple logo with no progress bar or a stopped progress bar, for over ten minutes.
    For more information on this, take a look at:
    iOS: Unable to update or restore
    http://support.apple.com/kb/ht1808
    Best of luck,
    Mario

  • My computer no longer recognizes my iPod Touch. And the iPod Touch does not recognize that it is connected to a computer.

    My computer no longer recognizes my iPod Touch. And the iPod Touch does not recognize that it is connected to a computer.  It has worked great for many days until today.
    I’ve tried two different Apple cables.
    I’ve tried different USB ports on the computer.
    I have rebooted both the Mac and the iPod.
    I’ve wiggled the cables and checked for dust in the connectors.
    The iPod charges using this same cable connected to wall wart.  That’s a good sign.
    Both the Mac and iPod seem to work fine separate from each other.  They just won’t talk anymore.
    Mac mini
    1.83 GHz Intel Core Duo
    OS 10.4.11
    iTunes 9.2.1
    iPod Touch 32GB, version 3.1.3 (7E18), model PB533LL 

    I found this possible solution on another support thread, so I tried it.
    turn off iPod
    hold Sleep and Home buttons to start it.
    When Apple appears, let go of Sleep button, but keep holding Home button.
    When screen goes blank, let go of Home button.
    Connect cable and check iTunes to see if it has conencted.
    This did not work for me.
    I then turned off the iPod, restarted the Mac, and restarted the iPod normally.
    I connected them with the cable, and it works like normal.  :-)

  • My ipod touch won't respond. Shortly after I downloaded IOS 8, it quite responding. How can I get my pictures recovered?

    My ipod touch won't respond. Shortly after I downloaded IOS 8, it quite responding. All I get is the Apple sign.  I connected to my computer and tried updating and was able to download the USB connection for the device but received an error when it tried to update the ipod. Is there any way to retrieve my pictures from the device before I try to recover? At this point my pictures are more valuable to me than restoring the device.  How can I get my pictures recovered?
    Now it looks like I have the Apple with an line under it on the screen, but still not responsive.

    Check for hardware issues
    Related errors: 1, 3, 10, 11, 12, 13, 14, 16, 20, 21, 23, 26, 27, 28, 29, 34, 35, 36, 37, 40, 1000, 1002, 1004, 1011, 1012, 1014, 1667, or 1669.
    These errors mean that your device or computer may have a hardware issue that's preventing the update or restore from completing.
    Check that your security software and settings aren't preventing your device from communicating with the Apple update server.
    Then try to restore your iOS device two more times while connected with a cable, computer, and network you know are good.
    Confirm that your security software and settings are allowing communication between your device and update servers.
    If you still see the error message when you update or restore, contact Apple support.
    If still problem, make an appointment at the Genius Bar of an Apple store since it appears you have a hardware problem.
      Apple Retail Store - Genius Bar

  • IPod touch won't charge, not recognized by iTunes or Finder

    Hi -
    My iPod 4th gen - version 6.1.2 stopped charging midway, now not recognzed by iTunes or Finder. Battery won't charge. I have been through the diagnostics, reset, rebooted, etc. USB ports are OK...
    Bad cable seems unlikely - it worked before...
    I saw the advice about updating software, but if the device is not connected, so how could I do that?
    Thanks,
    David

    Try:
    - iOS: Not responding or does not turn on
    - Also try DFU mode after try recovery mode
    How to put iPod touch / iPhone into DFU mode « Karthik's scribblings
    - If not successful and you can't fully turn the iOS device fully off, let the battery fully drain. After charging for an least an hour try the above again.
    - Try on another computer
    - If still not successful that usually indicates a hardware problem and an appointment at the Genius Bar of an Apple store is in order.
    Apple Retail Store - Genius Bar       
    and/or
    Not Charge
    - See:      
    iPod touch: Hardware troubleshooting
    - Try another cable. Some 5G iPods were shipped with Lightning cable that were either initially defective or failed after short use.
    - Try another charging source
    - Inspect the dock connector on the iPod for bent or missing contacts, foreign material, corroded contacts, broken, missing or cracked plastic.
    - Make an appointment at the Genus Bar of an Apple store.
    Apple Retail Store - Genius Bar

Maybe you are looking for

  • How can I launch firefox on different displays simultaneously without creating profiles for each of them

    On my solaris server, there is an application which, in order to display some information, opens the browser. The server can be accessed thorugh X windows by various users. The issue is that whn firefox is open on one display, it fails to open on ano

  • IPad volume too low on Apple TV when watching movies

    Hi. I have the latest Apple TV, 3rd Gen iPad and Retina MacBook Pro.  If I play any movie through Apple TV using my iPad (using Video App) the volume is often far too low.  This means that I have to turn my Amp/Speakers up (to around +60; +40 is norm

  • Processor and Graphics query for G4 PowerMac 'Digital Audio'

    Hey all, two questions here... Question 1 Ive got ANOTHER new processor and graphics card for my Digital Audio G4. The processor i had in it before was a Sonnet Encore ST/G4 1GHz, ive replaced this with the same make of processor but at 1.4GHz. The p

  • Office delegation permissions

    Hi all, Enviroment: Office 365 Enterprise E3 with Azure AD on cloud Problem: I'm setting up a delegated connection to email account, and I face some permission problems on which i would like to know if it is solvable at all. Let's say that I have a m

  • Help! My adobe photoshop elements 9 won't work when i open it up!

    Help, please! I have a Adobe Photoshop elements 9 and everytime i save a picture then the next day i try to open my save picture it tells me "This product has encountered a problem which requires that you restart your computer before it can be launch