Ipod write protection error - disk is locked and cannot be written to

Has anyone experienced this 'disk is locked and cannot be written to' when trying to update their ipod mini? I've tried everything, including all 4 R's, but still get the same message. And now that i've restored my ipod to its factory settings, I can no longer see my ipod in iTunes 7. So frustrating! Any thoughts are appreciated...i've just about given up. thanks.
iPod Mini   Windows XP Pro  

Welcome to Apple Discussions!
First off, make sure everything is updated...
http://www.apple.com/ipod/download
http://www.apple.com/itunes/download
Now see if restoring your iPod helps...
http://docs.info.apple.com/article.html?artnum=60983
btabz

Similar Messages

  • "The iPod '...' cannot be synced. The disk is locked and cannot be written to."

    Hello.
    I keep getting this "The iPod '...' cannot be synced. The disk is locked and cannot be written to." error when I try to sync my 11 GB of music from my very old, updated Windows XP Pro SP3 machine to an old iPod Touch 1G (iOS v3.1.3). It has a brand new (lat/new)est iTunes installation too. I tried rebooting the the machine, disconnecting USB cables, etc. None of them helped. I did not have this problem in the end of 2013. Is my iPod Touch 1G dying?
    Thank you in advance.

    lllaass wrote:
    Try:
    - Reset the iOS device. Nothing will be lost      
    Reset iOS device: Hold down the On/Off button and the Home button at the same time for at
    least ten seconds, until the Apple logo appears.
    - Reset all settings                            
    Go to Settings > General > Reset and tap Reset All Settings.
    All your preferences and settings are reset. Information (such as contacts and calendars) and media (such as songs and videos) aren’t affected.
    - Restore from backup. See:                                               
    iOS: Back up and restore your iOS device with iCloud or iTunes
    - Restore to factory settings/new iOS device.                     
    - Try on another computer 
    I did a reset since I had to restore v3.1.3 firmware and reconfigure from a Mac OS X 10.5.8 MBP before I ran into problems. Isn't that enough? Or do I have to do it again? Also, these were brand new installations and setups for iTunes and iPod Touch 1G. So, I am doing everything from scratch.
    I also found out that iTunes wants full (not read) access to my shared medias in my very old, updated Windows XP Pro SP3 machine. When I gave them full access, then I got farther, but it still failed later on (almost half way since 5 out of 11 GB according to math with disk spaces on both iTunes and iOS v3.1.3?) I didn't use Mac OS X 10.5.8's iTunes (only kept it for whited00r firmware part) for syncing since all my media is on the other machine.

  • 'This disk is locked and cannot be written to'

    After transferring music to new PC, when trying to update iPod Mini, keep getting error message:
    "Attempting to copy to the disk "SUSIE'S IPO" failed. The disk is locked and cannot be written to".
    What am I doing wrong?

    Welcome to Apple Discussions!
    First off, make sure everything is updated...
    http://www.apple.com/ipod/download
    http://www.apple.com/itunes/download
    Now see if restoring your iPod helps...
    http://docs.info.apple.com/article.html?artnum=60983
    btabz

  • The attempt to burn a disc failed. The disk is locked and cannot be written

    I am having a problem burning CDs. iTunes begins to burn CD than cancels with the following message "The attempt to burn a disc failed. The disk is locked and cannot be written." After some research I found the following article "Burning disc in iTunes for Windows using a Sony CD-RW/DVD CRX830E model drive fails with 4280 error." I followed directions as noted, this worked for the burning of one CD, then failed message returned. I have tried different CDs and lowering record speed to no avail. Burner worked up until updating to latest iTunes. Here is the diagnostic report
    Microsoft Windows XP Professional Service Pack 2 (Build 2600)
    Sony Corporation PCG-GRT390ZP(UC)
    iTunes 7.0.2.16
    CD Driver 2.0.6.1
    CD Driver DLL 2.0.6.1
    LowerFilters: PXHELP20 (2.0.0.0), AFS2K (3.1.21.0),
    UpperFilters: GEARAspiWDM (2.0.6.1),
    Video Driver: NVIDIA GeForce FX Go5600 (Sony)\GeForce FX Go5600
    IDE\DiskIC25N060ATMR04-0______________________MO3OAD1A, Bus Type ATA, Bus Address [0,0]
    USBSTOR\DiskLexar__JumpDrive______1.00, Bus Type USB
    USBSTOR\DiskSony___MSC-U04________3.00, Bus Type USB
    IDE\CdRomSONYCD-RW__CRX830E_____________________JFK1___, Bus Type ATA, Bus Address [0,0]
    If you have multiple drives on the same IDE or SCSI bus, these drives may interfere with each other.
    Some computers need an update to the ATA or IDE bus driver, or Intel chipset. If iTunes has problems recognizing CDs or hanging or crashing while importing or burning CDs, check the support site for the manufacturer of your computer or motherboard.
    Current user is an administrator.
    E: SONY CD-RW CRX830E, Rev JFK1
    Media in drive is blank.
    Get drive speed succeeded.
    The drive CDR speeds are: 4.
    The drive CDRW speeds are: 4 0 0 0 0 0 0 0.
    The last failed audio CD burn had error code -46(0xffffffd2). It happened on drive E: SONY CD-RW CRX830E on CDRW media at speed 4X.
    Any help would be appreciated.
    Sony Vaio Windows XP

    hmmmm. i see that there's a chipset driver revision listed on the drivers and downloads page for your M520:
    Gateway M520 > Windows XP
    are your chipset drivers currently up to date?

  • Disk is locked and cannot be written to???

    Just bought a brand new, second gen 8gb ipod nano.
    Newest iTunes and newest software on ipod.
    When i connect the ipod it comes up fine in iTunes, but if i try and alter settings in ipod summary and click apply, or copy music across i get the following error message:
    [img]http://i13.photobucket.com/albums/a297/batman_dave/ipoderror.jpg[/img]
    The hold button is off, i have tried resetting and restoring the ipod and it hasnt helped.
    Thanks for your help

    Welcome to Apple Discussions!
    First off, make sure everything is updated...
    http://www.apple.com/ipod/download
    http://www.apple.com/itunes/download
    Now see if restoring your iPod helps...
    http://docs.info.apple.com/article.html?artnum=60983
    btabz

  • Why does my iphone say the disk is locked and cannot be written to?

    i am trying to sync my songs to my iphone but this stupid message keeps on popping up

    lllaass wrote:
    Try:
    - Reset the iOS device. Nothing will be lost      
    Reset iOS device: Hold down the On/Off button and the Home button at the same time for at
    least ten seconds, until the Apple logo appears.
    - Reset all settings                            
    Go to Settings > General > Reset and tap Reset All Settings.
    All your preferences and settings are reset. Information (such as contacts and calendars) and media (such as songs and videos) aren’t affected.
    - Restore from backup. See:                                               
    iOS: Back up and restore your iOS device with iCloud or iTunes
    - Restore to factory settings/new iOS device.                     
    - Try on another computer 
    I did a reset since I had to restore v3.1.3 firmware and reconfigure from a Mac OS X 10.5.8 MBP before I ran into problems. Isn't that enough? Or do I have to do it again? Also, these were brand new installations and setups for iTunes and iPod Touch 1G. So, I am doing everything from scratch.
    I also found out that iTunes wants full (not read) access to my shared medias in my very old, updated Windows XP Pro SP3 machine. When I gave them full access, then I got farther, but it still failed later on (almost half way since 5 out of 11 GB according to math with disk spaces on both iTunes and iOS v3.1.3?) I didn't use Mac OS X 10.5.8's iTunes (only kept it for whited00r firmware part) for syncing since all my media is on the other machine.

  • TS1363 my ipod shuffle downloaded a few songs, but now says that it's locked and cannot be written to.  Any suggestions?

    \my ipod shuffle downloaded a few songs, but now says that it's locked and cannot be written to.  Any suggestions?

    Hello musicalgal4377,
    The following article details a number of likely causes for this particular message.
    'Disk cannot be read from or written to' when syncing iPod or 'Firmware update failure' error when updating or restoring iPod
    http://support.apple.com/kb/HT1207
    Cheers,
    Allen

  • Write protection error with my soundblaster live

    Running win ME and cannot fully install soundblaster software disk.Doing a complete install.When system reboots,blue screen with the "Write Protection Error".Have to shut down comp with power switch. Then when I turn it back on,it comes up in safe mode.When I uninstall soundblaster,comp comes back to desktop. I have also tried to install with win XP home edition upgrade with the same results. I have formatted my entire comp many times since I purchased Soundblaster li've 5.. Any help would be greatly appreciated.

    Glennvi
    Try moving the sound card to another PCI slot and then run the installation from the CD again. There is an article on Microsoft knowledgebase that cover the Windows error you encounter that you can refer to.
    http://support.microsoft.com/default...kb;en-us;49962
    If you are still having problem with that, you may like to contact Support for further advise.
    http://us.creative.com//support/custsup/
    Jason
    Message Edited by Jason-CL on 0-5-2004 :09 PM

  • How can I unlock my ipod touch?  The screen is locked and has various languages on the sliding bar.  It wont let you touch it

    how can I unlock my ipod touch?  The screen is locked and has various languages on the sliding bar.  the screen is grey and the normal screen saver is gone.

    As a first attempt, try a reboot by holding both the power and home buttons untl the apple logo appears and it restarts, ignoring the red slider if that appears.

  • Ipod have 22,773,688 minutes. someone stole ipod got it back but its lock and cant get into it.help

    My ipod has 22,773,688 minutes. Someone stole ipod got it back but its locked and cant get in it?

    Place the iOS device in Recovery Mode and then connect to your computer and restore via iTunes. The iPod will be erased.
    iOS: Wrong passcode results in red disabled screen                          
    If recovery mode does not work try DFU mode.                         
    How to put iPod touch / iPhone into DFU mode « Karthik's scribblings         
    For how to restore:
    iTunes: Restoring iOS software
    To restore from backup see:
    iOS: How to back up
    If you restore from iCloud backup the apps will be automatically downloaded. If you restore from iTunes backup the apps and music have to be in the iTunes library since synced media like apps and music are not included in the backup of the iOS device that iTunes makes.
    You can redownload iTunes purchases by:
    Downloading past purchases from the App Store, iBookstore, and iTunes Store

  • My install of maverick failed as disk is damaged and cannot repaired. I tried to erase disk but got error that disk cannot be umounted. Please help! Thank you very much.

    My install of maverick failed as disk is damaged and cannot repaired. I tried to erase disk but got error disk cannot be unmounted. Please help. What can i do? Thank you very much.

    First have you got a backup of your data? If not try to get one now while you have some access to the drive. The drive is probably faulty and will need to be replaced, without the backup you risk losing the data.
    Have you a bootable external USB drive with Mavericks on it, if so boot from that and try and repair or erase the drive and reinstall Mavericks.
    If you don't have Mavericks on an external drive,  boot from you Leopard DVD ( I am presumimg your profile is correct) and run Disk Utility from there, you may be able to erase the drive and reload Leopard. You can then install Mavericks. Even if all that works you will most likely need a new drive in the near future.

  • I downloaded the mountain lion from the app store and it downloaded. when i installed the mountain lion it said that the hd disk is broken and cannot be repaired, and the other disk doesnt have enough space!

    I downloaded the mountain lion from the app store and it downloaded. When i installed the mountain lion it said that the hd disk is broken and cannot be repaired, and the other disk doesnt have enough space! HELP and i cannot return to my desktop with the old sofware so i cant use my computer normaly

    This error means that your hard drive is badly corrupt and cannot be repaired by Disk Utility. Since you say you don't have backups, this is very bad news. You may already have lost data irrevocably.
    First order of business needs to be backing up whatever you can, but this may be difficult to do if the machine won't start up any more. See step 1 of the following post:
    https://discussions.apple.com/message/21614450#21614450
    Once you have backed up your data, you can address the other issues.

  • Restore needed on screen but iTunes says phone is locked and cannot connect

    restore needed on screen but itunes says phone locked and cannot connect

    now it says cannot restore from itunes (error 1)

  • "Disk Utility has lost its connection with the Disk Management Tool and cannot continue. Please quit and relaunch Disk Utility."  Trying to format my iomega external HD for use with Mac

    Hi. Trying to connect iomega ext. HD. i have to reformat for Mac. When i plug in & go to Disk Utility,the external shows up and i'm supposed to click "partition". When i do, a box comes up saying ""Disk Utility has lost its connection with the Disk Management Tool and cannot continue. Please quit and relaunch Disk Utility." I quit and relaunched, same results. After googling my question, i came up with this:
    "Disk Utility has lost its connection with the Disk Management Tool and cannot continue. Please quit and relaunch Disk Utility."
    (Quitting and reopening Disk Utility does not help.)
    The following also appears in Console log:
    *** malloc[419]: Deallocation of a pointer not malloced: 0x290a410; This could be a double free(), or free() called with the middle of an allocated block; Try setting environment variable MallocHelp to see tools to help debug : for architecture i386 object: ./Applications/iTunes.app/Contents/MacOS/iTunes malformed object (unknown flavor for flavor number 0 in LC_UNIXTHREAD command 27 can't byte swap it)
    Workaround
    Quit Disk Utility.
    From the Finder's Go menu, choose Go to Folder....
    Type the following, then click OK: /Library/Receipts
    Temporarily remove these iTunes receipts from /Library/Receipts (sort the folder alphabetically as a list):
    iTunes.pkg
    iTunes4.pkg
    You can put them on the desktop, for example. Do not remove iTunesX.pkg or iTunes Phone Driver.pkg.
    Open Disk Utility and repair disk permissions again.
    Quit Disk Utility.
    Put the removed iTunes receipts back in /Library/Receipts.
    Note: This issue does not affect Disk Utility's verify or repair disk features.
    All seemed good, for a moment, until, upon going back to Disk Utility after removing itunes4.pkg and putting on desktop (i did not have itunes.pkg to remove) the same thing was happening. When i highlite my iomega ext. on left of page, disk perrmissions is grayed and does not allow me to click on it. Same problem from the start. Can somebody please help me out here? That would soooo awesome. Thanx!

    i'm just scared i will do something wrong on my own and lose my data.
    You shouldn't be scared of that, because you should already have backups. If you don't have backups, then backing up is the first priority.
    Insert the Snow Leopard DVD and restart. When you hear the chime, hold down the C key and keep holding it until the Apple logo appears on the display. You should now see the language selection screen. Select your language, then choose Utilities > Disk Utility from the menu bar. In the Disk Utility window, select the external drive (not the internal). The drive may already have a data partition, in which case there will be another icon below the drive icon. Choose the drive icon, then select the Partition tab. Create a single partition with the default options (GUID partition table, Mac OS X Extended Journaled).
    When the partitioning is done, select the startup volume on your internal drive in the DU window. Select the Restore tab. Drag the icon of the startup volume to the "Source" field. Then drag the icon of the newly-created volume on the external drive to the "Destination" field. Make sure you have this right. Then click the Restore button, and the data on your startup volume will be copied to the external drive.

  • I get the error message 150:30 and cannot open pse.  What do I do?

    Trying to use photoshop I get the error message 150:30 and cannot open pse.  What do I do?

    Error "Licensing has stopped working" | Mac OS
    Error "Licensing has stopped working" | Windows
    Mylenium

Maybe you are looking for