Iprint from remote sites
Hello folks.
Iprint works perfectly in house. Our internal network sits behind
a BM3.8 firewall. I'm trying to download the iprint client from a
customers site but keep getting a winsock error 10060. The clients
site is also behind a BM3.8 firewall.
What port exceptions do I need to create on our BM server and the
customers BM server to get this to work? Basically I just need the
port numbers required outbound from the Client site, and inbound
at our site. 631, 515 is there anything else that would relate to
the 10060 winsock error? I get that error when trying to download
the driver. The web page is up, I have downloaded the client and
installed, but cannot pull the driver?
Thanks for your help.
Martin Stepanek
martin@image"Hyphen"technology"DOT"com (
'mailto:martin@image"Hyphen"technology"DOT"com' )
www.image-technology.com
Ah yah sir, I did a find the cure!
It wasn't packet filtering nor generic proxy. It was in fact on
page "uh let me thing...uhhhhh, possum, uh dinosaur..ahhhh, no
what page was that on? Ding dang, it was either 14 or 17 of the
iprint administators guide.
Any case, notice when attempting to install the drivers remotely
(or internally for that matter) that the ipp url was an internal
ip address. Couldn't change that in edir so looking at the manual
again I found this little note suggesting to start the ndps
manager with the /dnsname switch. ex: Load ndpsm
..manager.domain.com /dnsname=server.domain.com . The manual
suggesting setting up a dns record for the print manager but I
figured if its mapping to the same IP as the server name then lets
use the server name. That should work and voila.
caio
>>> On 7/29/2006 at 10:10 AM, in message
<[email protected]>, Martin
Stepanek<[email protected]> wrote:
> Hello folks.
>
> Iprint works perfectly in house. Our internal network sits
> behind
> a BM3.8 firewall. I'm trying to download the iprint client
> from a
> customers site but keep getting a winsock error 10060. The
> clients
> site is also behind a BM3.8 firewall.
>
> What port exceptions do I need to create on our BM server and
> the
> customers BM server to get this to work? Basically I just need
> the
> port numbers required outbound from the Client site, and
> inbound
> at our site. 631, 515 is there anything else that would relate
> to
> the 10060 winsock error? I get that error when trying to
> download
> the driver. The web page is up, I have downloaded the client
> and
> installed, but cannot pull the driver?
>
> Thanks for your help.
Similar Messages
-
The WSDL data cannot be retrieve from remote site
I am a new guy learning web services with NetBeans 5.5 and meet some problem in retrieving wsdl data from remote site.
I create a web service "WSTestServer" at Sun Application Server PE8.2 with real IP, say 111.110.11.10:8888, and there's a class "TestWS" with a method "getWS" to return a String. The server (or machine) name is ultra20. So, by following steps in NetBeans, I can get a wsdl file after generating the web service and it can be viewed at
http://111.110.11.10:8888/WSTestServer/TestWS?WSDL
Then, I create a web service client at the same machine, it is available to test this method by clicking Web Service Reference item in NetBeans and select "getWS" method to get that String.
However, when I create a web service client at remote site, it doesn't work and show exception message like
cannot find domain http://ultra20:8888/WSTestServer/TestWS....
I go back to check wsdl file, at the last line, it prints like
<soap:address location="http://ultra20:8888/WSTestServer/TestWS".....
If I test this case in LAN, e.g., the server IP becomes 192.168.1.2 and client IP is 192.168.1.3, then it works since machine name can be recognized within the same local area network. I try to revise the wsdl file above to replace machine name as real IP, but it is automatically changed back with machine name while deploying and copy the revised one as xxx.wsdl__orig.
Should I do additional configuration setup for server site? Such as, registering a domain name like aaa.bbb.edu instead of 111.110.11.10?
Any comment and help for this subject is appreciated!!
Thank you so much!Works as designed,from documentation:
The database also retrieves all triggers and constraints defined on the table except for referential integrity constraints that reference other tables.
The retrieved indexes, triggers, and constraints have recycle bin names. Therefore it is advisable to query the USER_RECYCLEBIN view before issuing a FLASHBACK TABLE ... TO BEFORE DROP statement so that you can rename the retrieved triggers and constraints to more usable names.
For details see the FLASHBACK TABLE command description for your unknown database version.
Werner -
Hello every one,
I tried to load the data from remote site to stagging area with DB link, i used append hint and it gave this error, I was just wondering?
ERROR at line 1:
ORA-12840: cannot access a remote table after parallel/insert direct load txnORA-06512: at "JAMES.PKGCONVERSION", line 464
any help please thank you
i am not using all the columns, i am using selec in the insert. Thank you in advance
Message was edited by:
user553284I had commit after three inserts, I changed commit after each insert, it is working now,
Does that really matter?
Any idea please.
Thank you -
Connection from remote sites (Frame Relay WAN) to AS/400 dissapears
Hello,
We have the following problem appearing in our environment:
All connections from remote sites dissapears unexpected from AS/400. After 2-3 minutes remote users get normal connectivity again.
The environment is the the following:
Frame Relay/ATM WAN (Frame Relay on remote sites and ATM in datacenter) comes to Cisco 7204VXR router which connected to LAN switch with 10/100/1000 ports. AS/400 with Fast Ethernet interface also connected to the similar LAN switch. CEF is enabled on the router, IOS version 12.4.3a. We have ETHSTD *ALL parameter set on AS/400. Remote users uses TCP/IP and Telnet but there are a number of 5494 controllers wich uses SNA.
We got the problem for the first time after we enabled CEF on the router.
I suspect that the cause of problem is Ethernet frames of different standards due to ETHSTD *ALL, but can neither reproduce the problem nor understand why it behaves so.
Have anybody had similar problem?
I would be very thanksfull if somebody can help me to solve it.
Thank you in advance.
//Mikhail GaliulinHi Martin,
Cisco 7200 itself can access AS/400 as well as all other hosts in the same with AS/400 LAN. There is no any outage in communications which goes to another LAN segment via Netscreen firewall while the communication via Cisco is down. Only those hosts which connected via Cisco are experiencing the problem. I can not say where the traceroute from AS/400 stucks (there are other people who maintain the machine and they never could catch the exact moment of outage).
To turn off CEF I treat as the last option actually and unfortunatelly there is no guarantee that software upgrade will help (we have 12.4.3a now).
So first of all I'm trying to understan WHY it happens because I can not see any systematics in the problem appearance. It can happen 3 times under 2 days and then dissapear for 1-2 months...
//Mikhail Galiulin -
Partition ERROR - 1023040 - msg from remote site : need to understand
hi,
I currently have a problem with the partitions between two cubes.
Architecture:
80 countries database (source)
1 world database (destination)
Process :
- The partitions are created dynamically by maxl scripts :
spool on to $1;
Alter application $2 comment '**_batch_**';
Alter application $4 comment '**_batch_**';
Alter system load application $2;
Alter system load application $4;
Alter application $2 disable startup;
Alter application $4 disable startup;
Alter application $2 disable connects;
Alter application $4 disable connects;
/* Create Transparant Partition between Country cube to Mond cube */
create or replace replicated partition $2.$3
AREA
'"S_R_N",
&curr_month,
&local_currency, "D_EURO",
@IDESCENDANTS("P_Produit"),
@LEVMBRS("M_Marche",1),"M_Marche",
@IDESCENDANTS("B_Marque"),
@IDESCENDANTS("U_Sourcing"),
@REMOVE (@DESCENDANTS("I_Masse"), @LIST ("I_55CCOM")), @DESCENDANTS("I_Divers"),
@IDESCENDANTS("NA_Nature"),MCX'
to $4.$5
AREA
'"S_R_N",
&curr_month,
"D_DEV", "D_EUR",
@IDESCENDANTS("P_Produit"),
@LEVMBRS("M_MixClient",0),"M_MixClient",
@IDESCENDANTS("B_Marque"),
@IDESCENDANTS("U_Sourcing"),
@REMOVE (@DESCENDANTS("I_Masse"), @LIST ("I_55CCOM")), @DESCENDANTS("I_Divers"),
@IDESCENDANTS("NA_Nature"),MCX,
&country_name'
mapped globally ('',D_$7, "D_EURO", "M_Marche") to (W_$6,D_DEV, "D_EUR", "M_MixClient")
refresh replicated partition $2.$3 to $4.$5 all data;
drop replicated partition $2.$3 to $4.$5;
Alter application $2 enable startup;
Alter application $4 enable startup;
Alter application $2 enable connects;
Alter application $4 enable connects;
Alter application $2 comment '**_enable_**';
Alter application $4 comment '**_enable_**';
Alter system unload application $2;
Alter system unload application $4;
Spool off;
Logout;
exit;
- Defragmentation cubes, launch replications countries successively one by one to the world cubes sequentially .
the order of the country is not the same from one month to another .
Treatment is initiated each month.
Symptoms :
- Partition fall into error with the following message but not systematically .
message:
MAXL > refresh replicated partition PGC_ESP.Pgc_esp PGC_MOND.Pgc_mond to all data ;
ERROR - 1023040 - msg from remote site [ [ Wed Nov. 29 10:21:03 2013] hprx1302/PGC_MOND/Pgc_mond/PGC_ADMIN/Error ( 1023040 ) msg from remote site [ [ Wed Nov. 29 10:21:02 2013] hprx1302 / PGC_ESP / Pgc_esp / PGC_ADMIN / Error (1023040) msg from remote site [ [ Wed Nov. 29 10:21:01 2013] hprx1302/PGC_MOND/Pgc_mond/PGC_ADMIN/Error ( 1042012 ) Network error [ 32] : Can not Send Data ]]] .
We note that the error occurs in the following cases:
- The errerur happens generally when the average clustering ratio is low. (cube fragmented) for cubes source and / or destination
- When beacuoup replication were done before: in the last 10 to 15 cubic remaining replicate.
- We mistake once on the environment recipe on the first cube with average clustering ratio to 0.96 but the server recipe is much less efficient.
We noticed that when doing a defragmentation cubes source and destination once the error obtained treatment replication was no longer falling into error.
Problem: defragmentation cube world take 10 hours.
We also made the following observation:
OK/INFO - 1051034 - Logging in user [PGC_ADMIN].
OK/INFO - 1051035 - Last login on Friday, November 29, 2013 10:19:46 AM.
OK/INFO - 1053012 - Object [Pgc_esp] is locked by user [PGC_ADMIN].
OK/INFO - 1053012 - Object [Pgc_mond] is locked by user [PGC_ADMIN].
OK/INFO - 1053012 - Object [54116855] is locked by user [PGC_ADMIN].
OK/INFO - 1053012 - Object [39843334] is locked by user [PGC_ADMIN].
OK/INFO - 1053013 - Object [54116855] unlocked by user [PGC_ADMIN].
OK/INFO - 1053013 - Object [39843334] unlocked by user [PGC_ADMIN].
WARNING - 1241137 - [Target] - Partition definition is not valid: [Cell count mismatch: [1279464568200] area for slice [1] members per dimension [63 1 2 1 6 26 7 245 1 37955 ]].
OK/INFO - 1053012 - Object [25586652] is locked by user [PGC_ADMIN].
OK/INFO - 1053012 - Object [11329970] is locked by user [PGC_ADMIN].
OK/INFO - 1053013 - Object [25586652] unlocked by user [PGC_ADMIN].
OK/INFO - 1053013 - Object [11329970] unlocked by user [PGC_ADMIN].
WARNING - 1241137 - [Source] - Partition definition is not valid: [Cell count mismatch: [47895484140] area for slice [1] members per dimension [63 1 6 7 2173 2 17 1 245 ]].
OK/INFO - 1053013 - Object [Pgc_esp] unlocked by user [PGC_ADMIN].
OK/INFO - 1053013 - Object [Pgc_mond] unlocked by user [PGC_ADMIN].
OK/INFO - 1051037 - Logging out user [PGC_ADMIN], active for 0 minutes.
OK/INFO - 1241124 - Partition replaced.
Following these findings we need to understand what is happening.
We would like to understand why partitons fall errors?
why we have the message "Partition definition is not valid" in the logs when creating the partition?
Regards,
Oliv.Hi SreekumarHariharan,
Tx to your anwers, but we are already try all the solution proposes to Essbase FAQ.
a)Increase the values for NETDELAY and NETRETRYCOUNT in essbase.cfg file.Restart the essbase server.
We are changed the two value in the essbase.cfg but nothing to do. The same error appears
b)Make sure that the all source members and target members used in partition are in sync
All member are diferent between source and target but a mapping are defined in the partition (see the partition maxl in my below message.
c)Validate the partition (look at the validation tab, it will give the numbers for each side of the partition ie source area and target area)
You can see the logs of validation partition :
WARNING - 1241137 - [Target] - Partition definition is not valid: [Cell count mismatch: [1279464568200] area for slice [1] members per dimension [63 1 2 1 6 26 7 245 1 37955 ]].
OK/INFO - 1053012 - Object [25586652] is locked by user [PGC_ADMIN].
OK/INFO - 1053012 - Object [11329970] is locked by user [PGC_ADMIN].
OK/INFO - 1053013 - Object [25586652] unlocked by user [PGC_ADMIN].
OK/INFO - 1053013 - Object [11329970] unlocked by user [PGC_ADMIN].
WARNING - 1241137 - [Source] - Partition definition is not valid: [Cell count mismatch: [47895484140] area for slice [1] members per dimension [63 1 6 7 2173 2 17 1 245 ]].
OK/INFO - 1053013 - Object [Pgc_esp] unlocked by user [PGC_ADMIN].
OK/INFO - 1053013 - Object [Pgc_mond] unlocked by user [PGC_ADMIN].
OK/INFO - 1051037 - Logging out user [PGC_ADMIN], active for 0 minutes.
OK/INFO - 1241124 - Partition replaced.
d)Rerun the Partition script again
The same error appears.
Tx to your help.
Regards,
Oliv. -
Connecting to an ISDN BRI on a router from a PSTN line from remote site..!!
Friends,
I have a 1812 at HO with WIC1 BS/T Card, connected it to an ISDN BRI line.One of my critical remote location uses Leased circuit to reach my HO Router.But in case if LL goes down,some of the important PC's at the remote site should be able to dial to HO Router BRI Number using PSTN line, get connected and continue, ip address assigned from HO Router and access the application... Is any way available...Hi Arnab.
You need to configure dial backup through AUX port. You need to connect a normal PSTN line to a modem which in turn is connected to your AUX port. You will have to configure a chat script which you can find in the attachmnet. The attachment is a working example in one of my routers.
You also have to create an ASYNC interface. Check that in the attached file also
--Pls rate if useful--- -
Hi all , I have an exchange 2010 SP 2 environment with 2 sites , the remote site FL free busy has NEVER worked and I get this error on the remote site , is this related ?
thanks
Log Name: Application
Source: System.ServiceModel 3.0.0.0
Date: :
Event ID: 3
Task Category: WebHost
Level: Error
Keywords: Classic
User: SYSTEM
Computer: FL-CAS1.WOMBAT.LOCAL
free bust works from WITHIN the remote (FL ) site , but NEVER to the main (WASH) site , it has Never worked ,I am thing that this error is related
thanks I have no idea how to fix
Description:
WebHost failed to process a request.
Sender Information: System.ServiceModel.ServiceHostingEnvironment+HostingManager/17256489
Exception: System.ServiceModel.ServiceActivationException:
The service '/EWS/exchange.asmx' cannot be activated due to an exception during compilation. The exception message is: Could not find a base address that matches scheme http for the endpoint with binding CustomBinding. Registered base address schemes
are [https].. ---> System.InvalidOperationException:
Could not find a base address that matches scheme http for the endpoint with binding
++++Hi
This issue could be with corruption in Autodiscover and web services virtual directory
Replace Web.config file for Autodiscover and web services virtual directory from the other working site
Delete and Recreate Autodiscover and web services virtual directory
Do this only on the affected site
Remember to mark as helpful if you find my contribution useful or as an answer if it does answer your question.That will encourage me - and others - to take time out to help you Check out my latest blog posts on http://exchangequery.com Thanks Sathish
(MVP) -
IPSec VPN won't initiate from remote site
Hi all,
I have a site-to-site VPN configured between a 5520 at our data center, and a 1700 at a client's site for site-to-site connectivity. What I've noticed is, is that the VPN can only initiate from my Data Center, never from the client router. I can telnet into the router and start a telnet session sourced from the "inside" interface and it fails, yet I can see the NAT translations get created in the state table that should match the crypto-map. However, if I ping a host on the inside of the remote LAN from my workstation (behind the 5520) to bring the tunnel up, and run the exact same command on the client router once the tunnel is up, it works. Right now I have a continuous ping running from my workstation to keep the tunnel up, but obviously that's not the best solution
I had to modify this config to NAT the LAN addresses at the client to a non-overlapping subnet, so anything coming from 128.1.0.0/16 should be NAT'd to 192.168.105.[50-200]/24. I've also got two static NATs for inbound access from the data center and those seem to work fine.
I've pasted the config below, can anyone see what I might have missed?
Current configuration : 2787 bytes
! No configuration change since last restart
version 12.3
service timestamps debug datetime msec
service timestamps log datetime msec
service password-encryption
hostname hch-1721
boot-start-marker
boot-end-marker
enable secret 5 [REDACTED]
enable password 7 [REDACTED]
username support password 7 XXXXX
username bywater password 7 XXXXX
clock timezone MST -7
clock summer-time MDT recurring 2 Sun Mar 2:00 1 Sun Nov 2:00
mmi polling-interval 60
no mmi auto-configure
no mmi pvc
mmi snmp-timeout 180
aaa new-model
aaa authentication login default local
aaa session-id common
ip subnet-zero
no ip domain lookup
ip cef
ip audit po max-events 100
no ftp-server write-enable
crypto isakmp policy 1
encr 3des
hash md5
authentication pre-share
crypto isakmp key MYKEY address MYPEER
crypto ipsec transform-set hch_vpn esp-3des esp-md5-hmac
crypto map hch_vpn 10 ipsec-isakmp
set peer MYPEER
set security-association lifetime seconds 28800
set transform-set hch_vpn
match address 101
interface Ethernet0
description HCH Outside (to DSL Modem)
ip address 12.34.56.225 255.255.255.248
ip nat outside
half-duplex
no cdp enable
crypto map hch_vpn
interface FastEthernet0
description HCH Inside Intranet
ip address 128.1.0.75 255.255.0.0
no ip proxy-arp
ip nat inside
no ip mroute-cache
speed auto
full-duplex
ip nat pool hchpool 192.168.105.50 192.168.105.200 netmask 255.255.255.0
ip nat inside source list 50 pool hchpool overload
ip nat inside source route-map nonat interface Ethernet0 overload
ip nat inside source static 128.1.0.1 192.168.105.1
ip nat inside source static 128.1.247.4 192.168.105.2
ip nat outside source list 50 pool hchpool
ip classless
ip route 0.0.0.0 0.0.0.0 12.34.56.230
no ip http server
no ip http secure-server
access-list 20 permit REMOTEADMIN
access-list 20 permit REMOTESITE 0.0.0.255
access-list 20 permit 192.168.249.0 0.0.0.255
access-list 20 permit 128.1.247.0 0.0.0.255
access-list 20 permit 128.1.0.0 0.0.255.255
access-list 50 permit 128.1.0.0 0.0.255.255
access-list 101 permit ip 192.168.105.0 0.0.0.255 192.168.249.0 0.0.0.255
access-list 101 permit ip 128.1.0.0 0.0.255.255 192.168.249.0 0.0.0.255
access-list 110 deny ip 192.168.105.0 0.0.0.255 192.168.249.0 0.0.0.255
access-list 110 permit ip 128.1.0.0 0.0.255.255 any
access-list 133 deny tcp any any eq 135
access-list 133 deny tcp any any eq 445
access-list 133 deny tcp any any eq 5554
access-list 133 deny tcp any any eq 9996
access-list 133 permit ip any any
route-map nonat permit 10
match ip address 110
line con 0
line aux 0
line vty 0 4
access-class 20 in
exec-timeout 0 0
ntp clock-period 17179984
ntp server 198.72.72.10
endSo I took out the commands you said and replaced them with these:
ip nat inside source static network 128.1.0.0 192.168.105.0 /24 route-map hch-nat
route-map hch-nat permit 10
match ip address 150
access-list 150 permit ip 128.1.0.0 0.0.255.255 192.168.249.0 0.0.0.255
That gets it even more broken - with this I can't telnet from the inside interface even if I force the tunnel up.
Although now that I removed and re-added the above config it brings the tunnel up as expected now. Strange, yet irritating. -
Hello,
I used to have a separated branch office with its own application/db standalone server, and about 15 users locally configured on that server...
Recently we implemented a Microwave connection (25 Mbps) between the main and branch office, joined the server of the branch office as a member server of the main office domain and add users' accounts to the domain. So now remote users have there logon
and credentials from the DC in the main office but still work on there application/db member server located on the branch office.
The problem in this design is that when the connection occasionally goes down, users can't work on their application although there server is located on their same LAN, because they can't gain the necessary credentials from the DC/GC on the main site!!!
Would you please suggest any solution for this problem... do I have to make a local DC in the branch office, or create Child domain, or what?
PS.. I'm working on Windows 2003 domain
Thank you allGreetings!
If you are not running low on budget and bandwidth is not a concern, consider implementing an additional domain controller in your branch office and make it as global catalog.
Regards.
Mahdi Tehrani |
|
www.mahditehrani.ir
Please click on Propose As Answer or to mark this post as
and helpful for other people.
This posting is provided AS-IS with no warranties, and confers no rights.
How to query members of 'Local Administrators' group in all computers? -
How do I download my website from remote site to Dreamweaver
My server saved a copy of my website( built on a PC in CS3) from a year ago. I have a new Mac with CS5 now. How do I get the website beck onto my computer and functional? How can I do it and what questions should I be asking about how to do this?
figured it out.
-
Lookout server process control through modem from remote site
Hi!
I want to control the lookout version 5.0 server process from my office by using the simple 56k internal modem and telephone line. I know the congiguration for sever /Client for Local Area Network (LAN).
1. I have server process.
2. I have client process. (I start server process on client computer when server computer fails)
3. Internal modem (56 k)
4. Telephone Line.
Please send me the mateial which can help me in solving this problem.
Your response is highly appreciated.
Atif SarfrazAtif,
A couple of options are discussed in the the following thread:
http://forums.ni.com/ni/board/message?board.id=190&message.id=73
That was way back when VPN wasn't as common. Today... if you can VPN into your Server's network, then it will be a breeze since you are actually on the same network. But VPN via dial-up will be painfully slow.
Hope this at least gives you some ideas.
-Khalid -
How to get the entire database from remote server to my server
Hi,
I am running a web application with sample data. Now i need to access the original data through this application. But the original data is located in the other server which is located in Mumbai.
Now i need the copy of that database to my system(Chennai). with minimum effort.
It is very urgent...
Thanks in advance...
Chaitanya.Hi
Nicolas is right. You can also take advantage of exp/imp utility. That would not only get the entire db in one file but also the size will be a fraction of the entire db size.You can search for DataPump (that uses expdp and impdp) utility to expedite the export/import process.
For simple exp/imp you can do the following.
From Remote site(MUMBAI) issue
ORACLE_HOME\BIN\exp file=c:\fulldbexp09sept05.dmp log=c:\fulldbexp09sept05log.log FULL=Y userid=system/pwd@connectstringOfyourdb
Get a copy of fulldbexp09sept05.dmp and place it on your local drive in Chennai
On Local Site (Chennai)
ORACLE_HOME\BIN\imp file=fulldbexp09sept05.dmp log=fulldbimp09sept05 FULL=Y userid=system/pwd@connectstringOfyourlocaldb
By this you can take advantage of having a different db name on remote and local sites. This is a fairly easy exercise. You just need to be sure that in your TNSNAMES.ORA you have correctly defined the connectString for your db.
PS: Create a database on local server with default settings.
Make use of following to create appropriate tablespaces and users if you desire ie.
1. On Remote Site open SQLPLUS session and issue this command to find out the tablespaces, datafiles and their sizes
SQL>SELECT SUBSTR(file_name,1,60) FILE_NAME, tablespace_name, bytes
FROM dba_data_files
GROUP BY tablespace_name, file_name;
Now create the tablespaces on local sites using the result of the above query.
2. On Remote Site open SQLPLUS session and issue this command to spool user creation script.
SQL>spool c:\createuserscript.lst
SQL> SELECT 'CREATE USER ||' IDENTIFIED BY VALUES '||'"'||PASSWORD||'"'||' DEFAULT TABLESPACE '||DEFAULT_TABLESPACE||' TEMPORARY TABLESPACE '||TEMPORARY_TABLESPACE||';'
FROM dba_users
WHERE username NOT IN ('SYS','SYSTEM')
ORDER BY username;
SQL>spool off
Now edit this createuserscript using any editor and replace " with '. Copy this file to the local server and run it using @. This will create appropriate users.
Let me know if you have any problems.
Regards
Adnan Mashhadi
Nicolas I am not sure as how to eliminate the " in my script. Any comment will be appreciated. -
Is it possible to have someone log into my web site from a
remote site?
I would like to offer my service for other design companies
and would like
them to have the login process on their own web site and have
it query my
database and log into the proofing section of my site. Is
this possible with
web services?
Wally Kolcz
Developer / Support
ProjectProofing.comIs there anyplace I can find an example or demo of this?
Can they just use an include on their site to import a login
box to my site
or would it be better for me offer a prebuilt code they can
copy and paste
into their site to access my site? -
Hi,
I have a problem with Early Media functionality between Lync and Mediant 1000 E-SBC. If SBC Remote Early Media RTP parameter is set to Delayed (on IP Profile Settings level) i cannot establish connection. After receiving 183 Session progress (from Lync site)
call is released with 488 event (488 is sent from mediant site). Before "Not applicable here" in logs i can see:
6d:9h:46m:35s ( lgr_flow)(18219 ) #MediaResourcesConnector::AllocateMediaResources
(lgr_media_connector)(18220 ) MediaResourcesConnector:CalculateResourcesForAppExtensions Leading:DSP Opposite:NONE MediationLevel:NONE
(lgr_media_service)(18221 ) ServicesMngr: Allocate Media channel. current active: 0 and max is: 0
6d:9h:46m:35s (lgr_media_service)(18222 ) !! [ERROR] ServicesMngr: Cannot allocate more Media channel. current active: 0 and max is: 0
6d:9h:46m:35s (lgr_media_service)(18261 ) (#292) ChannelResource Deallocated.
6d:9h:46m:35s (lgr_media_service)(18262 ) (#293) ChannelResource Deallocated.
I need this because if im using SBC Remote Early Media RTP = Immidiately i cannot hear ringtone. Could someone give me any clues what is wrong in config?
I enclosed detailed logs:
Log is Activated 6d:9h:46m:35s ( lgr_sbc)(18057 ) (#51) SBCRoutesIterator Allocated.
( lgr_sbc)(18058 ) Classification Succeeded - Source IP Group #2.
( lgr_sbc)(18059 ) CallAdmission::AddDialog: Type INVITE Direction In IP group 2: 1 SRD 2: 1 SRD ovflw:1 used unres:1
( lgr_flow)(18060 ) (#51)SBCRoutesIterator::Change State From: InitialRouting To : AlternativeRouting
( lgr_sbc)(18061 ) CallAdmission::AddDialog: Type INVITE Direction Out IP group 1: 1 SRD 1: 1 SRD ovflw:1 used unres:2
( lgr_flow)(18062 ) (#51)SBCRoutesIterator::Next route found: Route by: IPGroup , IP Group ID: 1, Live:1
( lgr_sbc)(18063 ) Routing Succeeded -IP2IPRouting Rule #2.
( lgr_flow)(18064 ) ---- Incoming SIP Message from switch:5060 to SIPInterface #2 UdpTransportObject[#2] ----
6d:9h:46m:35s INVITE sip:1234@Mediant;user=phone SIP/2.0
Allow: INVITE, ACK, CANCEL, BYE, PRACK, NOTIFY, REFER, SUBSCRIBE, OPTIONS, UPDATE, INFO
Supported: replaces,timer,path,100rel
User-Agent: OmniPCX Enterprise R10.1.1 j2.603.33.a
Session-Expires: 1800;refresher=uac
Min-SE: 900
P-Asserted-Identity: "TPSA 12" <sip:221111111@switch;user=phone>
Content-Type: application/sdp
To: <sip:1234@Mediant;user=phone>
From: "TPSA 12" <sip:221111111@switch;user=phone>;tag=434636a077aeb3418ef3d5c0887debbd
Contact: <sip:221111111@switch;transport=UDP>
Call-ID: 5050e7eb34568795c049d14a6b088172@switch
CSeq: 1290334631 INVITE
Via: SIP/2.0/UDP switch;branch=z9hG4bK668ced008893ef177292c6f0f662ca02
Max-Forwards: 70
Content-Length: 265
v=0
o=OXE 1415263596 1415263596 IN IP4 switch
s=abs
c=IN IP4 172.16.20.32
t=0 0
m=audio 32156 RTP/AVP 8 4 97
a=sendrecv
a=rtpmap:8 PCMA/8000
a=ptime:20
a=maxptime:30
a=rtpmap:4 G723/8000
a=ptime:30
a=maxptime:30
a=rtpmap:97 telephone-event/8000
( sip_stack)(18066 ) New SIPMessage created - #57
( sip_stack)(18067 ) New SIPSBCCallLeg created - #1695
6d:9h:46m:35s ( sip_stack)(18068 ) New AcSIPCall created - #1922
( sip_stack)(18069 ) AcTransactionUser::AddMessageToQueue: Queueing message
6d:9h:46m:35s ( sip_stack)(18102 ) SIPCall(#1922) changes state from Idle to Invited
6d:9h:46m:35s ( sip_stack)(18164 ) SIPCall(#1921) changes state from Idle to Inviting
( sip_stack)(18165 ) SIPSessionTimer<TU#1921>::FillSTRequestData - Session-Timer mode: TRANSPARENT
( lgr_flow)(18166 ) ---- Outgoing SIP Message to Lync2:5068 from SIPInterface #1 TcpTransportObject[#648] ----
6d:9h:46m:35s ( lgr_flow)(18178 ) ---- Incoming SIP Message from Lync2:5068 to SIPInterface #1 TcpTransportObject[#648] ----
SIP/2.0 183 Session Progress
FROM: "TPSA 12"<sip:221111111@switch;user=phone>;tag=1c1656521459
TO: <sip:1234@Mediant;user=phone>;tag=499c98c8cd;epid=DE8F26F104
CSEQ: 1 INVITE
CALL-ID: 1656462877611201494635@Mediant
VIA: SIP/2.0/TCP Mediant:5068;branch=z9hG4bKac1657277504;alias
CONTACT: <sip:lyfe02.grupa.lukas:5068;transport=Tcp;maddr=Lync2>
CONTENT-LENGTH: 281
CONTENT-TYPE: application/sdp
ALLOW: CANCEL
ALLOW: BYE
ALLOW: UPDATE
ALLOW: PRACK
REQUIRE: 100rel
SERVER: RTCC/5.0.0.0 MediationServer
Rseq: 1
v=0
o=- 89 1 IN IP4 Lync2
s=session
c=IN IP4 Lync2
b=CT:1000
t=0 0
m=audio 52882 RTP/AVP 8 97
c=IN IP4 Lync2
a=rtcp:52883
a=label:Audio
a=sendrecv
a=rtpmap:8 PCMA/8000
a=rtpmap:97 telephone-event/8000
a=fmtp:97 0-16
m=audio 0 RTP/SAVP 8 4 97
( sip_stack)(18180 ) New SIPMessage created - #55
( lgr_flow)(18181 ) | |(SIPTU#1921)183 State:Proceeding(1656462877611201494635@Mediant)
6d:9h:46m:35s ( lgr_stk_ses)(18182 ) | | | #1694:SIP_ALERT_EV(1656462877611201494635@Mediant)
( sip_stack)(18183 ) SDPBody::New - id = 126
( sip_stack)(18184 ) SDPBodyMedia::New - id = 541
( sip_stack)(18185 ) SDPBodyMedia::New - id = 540
( sip_stack)(18186 ) <BaseSIP SDPSESSION #1694> UpdateChosenMediaByCN - CN as Remote -1
( sip_stack)(18187 ) SDPBodyMedia::New - id = 539
( sip_stack)(18188 ) SDPBodyMedia::New - id = 538
( lgr_stk_ses)(18189 ) SBCOfferAnswerMngr(#1694) changes state from SIP_MEDIA_OFFERING to SIP_MEDIA_COMPLETED
( lgr_stk_ses)(18190 ) <SESSION #1694> SendToCall - event: MEDIA_NEGOTIATION_COMPLETED_EV m_Call#1852
( lgr_flow)(18191 ) | | (#1852)SBCCall <- (#1694)SIPSBCCallLeg: MEDIA_NEGOTIATION_COMPLETED_EV
( lgr_flow)(18192 ) | (#59)SBCCallPlacementFeature <- (#1852)SBCCall: MEDIA_NEGOTIATION_COMPLETED_EV
( lgr_flow)(18193 ) | (#1853)SBCParticipantEndPoint <- (#59)SBCCallPlacementFeature: MEDIA_NEGOTIATION_COMPLETED_EV
6d:9h:46m:35s ( lgr_flow)(18219 ) #MediaResourcesConnector::AllocateMediaResources
(lgr_media_connector)(18220 ) MediaResourcesConnector:CalculateResourcesForAppExtensions Leading:DSP Opposite:NONE MediationLevel:NONE
(lgr_media_service)(18221 ) ServicesMngr: Allocate Media channel. current active: 0 and max is: 0
6d:9h:46m:35s (lgr_media_service)(18222 ) !! [ERROR] ServicesMngr: Cannot allocate more Media channel. current active: 0 and max is: 0
6d:9h:46m:35s (lgr_media_service)(18261 ) (#292) ChannelResource Deallocated.
6d:9h:46m:35s (lgr_media_service)(18262 ) (#293) ChannelResource Deallocated.
6d:9h:46m:35s ( lgr_flow)(18263 ) | | (#1853)SBCCall <- (#1695)SIPSBCCallLeg: RELEASE_EV
( lgr_flow)(18264 ) | | (#1853) SBCCall changing states from:AlertingState to:DisconnectingState
( lgr_flow)(18265 ) | (#1852)SBCParticipantEndPoint <- (#1853)SBCCall: RELEASE_EV
( lgr_flow)(18266 ) (#1852) SBCParticipantEndPoint changing states from:InitiatedState to:ReleaseingState
( lgr_flow)(18267 ) (#1035)SBCController <- (#1852)SBCParticipantEndPoint: RELEASE_EV
( lgr_flow)(18268 ) | | (#1035) SBCController changing states from:EstablishingState to:DisconnectingState
( lgr_flow)(18269 ) | (#1853)SBCParticipantEndPoint <- (#1035)SBCController: RELEASE_EV
( lgr_flow)(18270 ) (#1853) SBCParticipantEndPoint changing states from:InitiatedState to:ReleaseingState
( lgr_flow)(18271 ) | (#59)SBCCallPlacementFeature <- (#1853)SBCParticipantEndPoint: RELEASE_EV
( lgr_flow)(18272 ) (#59) SBCCallPlacementFeature changing states from: Initiated to: Releasing
6d:9h:46m:35s ( lgr_flow)(18273 ) | | (#1852)SBCCall <- (#59)SBCCallPlacementFeature: RELEASE_EV
( lgr_flow)(18274 ) | | (#1852) SBCCall changing states from:AlertingState to:DisconnectingState
( lgr_flow)(18275 ) | | | (#1694)SIPSBCCallLeg <- (#1852)SBCCall: RELEASE_EV
( sip_stack)(18276 ) New SIPMessage created - #52
( lgr_flow)(18277 ) | |(SIPTU#1921)DISCONNECT_REQ State:Proceeding(1656462877611201494635@Mediant)
( sip_stack)(18278 ) New SIPMessage created - #49
( lgr_flow)(18279 ) ---- Outgoing SIP Message to Lync2:5068 from SIPInterface #1 TcpTransportObject[#648] ----
CANCEL sip:1234@Mediant;user=phone SIP/2.0
Via: SIP/2.0/TCP Mediant:5068;branch=z9hG4bKac1657277504;alias
Max-Forwards: 70
From: "TPSA 12" <sip:221111111@switch;user=phone>;tag=1c1656521459
To: <sip:1234@Mediant;user=phone>;epid=DE8F26F104
Call-ID: 1656462877611201494635@Mediant
CSeq: 1 CANCEL
User-Agent: E-SBC/v.6.60A.260.002
Reason: SIP ;cause=488 ;text="488 Not Acceptable Here"
Content-Length: 0
( sip_stack)(18281 ) Resource SIPMessage deleted - #49
6d:9h:46m:35s ( sip_stack)(18354 ) New SIPMessage created - #42
( sip_stack)(18355 ) Resource SIPMessage deleted - #42
( lgr_flow)(18356 ) | | TransactionUserMngr::ReturnTransactionUser - #1921
( sip_stack)(18357 ) SIPCall(#1921) changes state from Disconnected to Idle
6d:9h:46m:40s ( sip_stack)(18358 ) New SIPMessage created - #47
( sip_stack)(18359 ) Resource SIPMessage deleted - #47
( lgr_flow)(18360 ) | | TransactionUserMngr::ReturnTransactionUser - #1922
( sip_stack)(18361 ) SIPCall(#1922) changes state from Disconnected to IdleHi,
On Mediant 1000 E-SBC SBC tab, when set Remote Early Media RTP Behavior to
Delayed, but also check if the following configuration set correctly:
SBC Media Security Behavior: SRTP
PRACK Mode: Optional
Remote Update Support: Supported Only After Connect
Remote Re-INVITE: Supported Only With SDP
Remote Delayed Offer Support: Not Supported
Remote REFER Behavior: Handle Locally
Remote 3xx Behavior: Handle Locally
Enforce MKI Size: Enforce
You can refer this
link
Note: Microsoft is providing this information as a convenience to you. The sites are not controlled by Microsoft. Microsoft cannot make any representations regarding the quality, safety, or suitability of any software or information found there.
Please make sure that you completely understand the risk before retrieving any suggestions from the above link.
Best Regards,
Eason Huang
Eason Huang
TechNet Community Support -
Just bought an iMac. I want to be able to "remote in" to work. I've been told to download software from Microsoft site but can see there are several versions available. Can anybody advise which one I need. Thanks
You mean Microsoft Remote Desktop Connection Client for Mac
Maybe you are looking for
-
Hi all, My iWeb 08 publishes to my web space within my mobile me package. After the change to me from .mac, I stopped using my @mac e-mail address and have started using @me instead. Further following a few issues when updating web galleries I decide
-
How to point apple tv to my iPad 2
I have just set up apple tv and set home share on my computer. Working fine.....but what if I find something on my iPad that I wish to display on my tv?
-
Whts the use of WebPass ... as documented it's used for helps communications b/w Identity Server and Webserver. Is there any other use of it? in detail?
-
FW8 on OSX : UNICODE FONT TROUBLE
Well ... Hi ! Can someone help me ... I'm new on MAC OSX ... but I use to work with FW ! On this OS, FW don't want to let me write with accent : é, à, ï ... won't appear. If I check with popchar the font table, i see that the accent are in the unicod
-
Can't get my USB keyboard to wake NB100 up from sleep - (Windows 7)
I use a monitor, USB wireless mouse and a USB wired keyboard with my NB100. My keyboard has a power button and it's set up to put the computer into sleep mode when pressed, which works fine. My problem is that the only way I can wake the computer is