IPS-4420 Global Correlation status critcal
How to check in the IPS 4420 is Globel correlation license are there or not?
In IDS 4420 IDM event montor page I am facing two below problem
1. Event Retrieval =========== Critical
2. Global Correlation =========== Critical.
I configure IPS box got to the Internet without proxy. But I don't how to check the IPS are connected to Cisco Global Correlation server?
Why its shwoing critcal on Event Retrieval and Global Correlation.
Are you planning to use the Global Correlation feature?
Here is the information on Global Correlation for your reference:
http://www.cisco.com/en/US/docs/security/ips/7.0/configuration/guide/idm/idm_collaboration.html
If don't want to use that feature, you can disable that in the sensor health metric section so it's not showing Critical.
Similarly, for Even Retrieval, you can just disable that in the sensor health metric section. This is only useful if your IPS events are retrieved by an external monitoring system, eg: IME.
http://www.cisco.com/en/US/docs/security/ips/7.0/configuration/guide/idm/idm_sensor_management.html#wp2117358
Message was edited by: Jennifer Halim
Similar Messages
-
Hello Everyone,
i'm trying to enable global correlation, but, after apply the configuration, i see the status bellow:
service global-correlation
network-participation off
global-correlation-inspection-influence aggressive
test-global-correlation off
exit
service aaa
exit
service analysis-engine
virtual-sensor vs0
physical-interface GigabitEthernet0/1
exit
exit
IPS-SITE-BACKUP#
IPS-SITE-BACKUP#
IPS-SITE-BACKUP#
IPS-SITE-BACKUP# show health
Overall Health Status Green
Health Status for Failed Applications Green
Health Status for Signature Updates Green
Health Status for License Key Expiration Green
Health Status for Running in Bypass Mode Green
Health Status for Interfaces Being Down Green
Health Status for the Inspection Load Green
Health Status for the Time Since Last Event Retrieval Green
Health Status for the Number of Missed Packets Green
Health Status for the Memory Usage Green
Health Status for Global Correlation Not Enabled
Health Status for Network Participation Green
Why the status is "not enabled"?
Obs: Downloads ok via proxy server.
Thanks.
RafaelHello Rafael,
Why the status is "not enabled
The status is not enabled because the participation of your IPS in the global correlation is off.
There are 3 states related to Global Correlation:
-Full
-Partial
-Off
Please change that and it should working, You need to have a DNS server set up in your IPS, if not Global Correlation will not work.
Julio
Rate the helpful posts -
Dear all,
IPS Correlation update will be done through the Management interface right? So I should confirm the ability of the IPS Management IP address to be able to access internet right?
I did so, but still not able to have global correlation update, what I am having each time I enable global correlation is a boost of traffic generated from the IPS and directed to the outside that is consuming the total internet link bandwidth.
What could be the reason behind this boost, and how may I troubleshoot the reason why the correlation is not being updated.
Regards,Hi,
I had the exact same problem that I solved to day.
Full connectivity but still the error:
# sh statistics global-correlation
Network Participation:
Counters:
Total Connection Attempts = 0
Total Connection Failures = 0
Connection Failures Since Last Success = 0
Connection History:
Updates:
Status Of Last Update Attempt = Failed
Time Since Last Successful Update = 3826 minutes
Counters:
Update Failures Since Last Success = 764
Total Update Attempts = 22747
Total Update Failures = 806
Update Interval In Seconds = 300
Update Server = update-manifests.ironport.com
Update Server Address = 204.15.82.17
Current Versions:
config = 1236210407
drop = 1312830724
ip = 1312830846
rule = 1312744926
# sh events error error warning past 12:00
evError: eventId=1304592381890230981 severity=error vendor=Cisco
originator:
hostId: xxxxxxxx
appName: collaborationApp
appInstanceId: 458
time: 2011/08/11 00:38:28 2011/08/11 02:38:28 GMT+01:00
errorMessage: name=errUnclassified A global correlation update failed: Failed download of ibrs/1.1/drop/default/1313021562 :
URI does not contain a valid ip address
Messages, like this one, in the category - Reputation update failure - were logged 49 times in the last 14699 seconds.
I found a tip when searching that worked for me :
Issue the: dns-secondary-server disable to flush DNS wait for GC to update again.
Thanks to: http://doublef.org/archives/cisco-ips-global-correlation-update-failures
HTH
Edit: I see a difference in our output, you don't have the ip address in update server field:
Update Server Address = Unknown
Might not bee the same problem. -
Global Correlation update Failure error
Hello,
I have received following error in IPS regarding global correlation update
A global correlation update failed: ExecLoadCollabUpdate control transaction failed: Control transaction cannot be completed at this time
is any one aware about this error? is it major issue and affecting IPS? I think this is because correlation update failure. Please let me know if any one has more information on this errorWhenever a global correlation update fails, an evError event is generated. The error message is included in sensor statistics. The following conditions result in a status message with the severity of Error:
•The sensor is unlicensed
•No DNS or HTTP proxy server is configured
•The manifest exchange failed
•An update file download failed
•Applying or committing the update failed
For global correlation update fails, refer
http://www.cisco.com/c/en/us/support/docs/security/ips-4200-series-sensors/50360-ids-faq.html -
MARS 6.0.4 reporting for IPS 7.0 Global Correlation Reputation Filtering
Does anyone know if there is a report available in MARS to see what IP addresses were denied by Reputation Filtering on IPS 7.0?
I found a report that shows attacks that were prevented due to global correlation score, but not for packets denied by Reputation Filtering.
Replies are greatly appreciated.
Thanks,
MarkThanks for the reply, but what I am looking for is reporting on what packets were dropped with Reputation Filtering(doesn't have a report in MARS) Not the GLobal Correlation risk rating blocks(Which does have a report available in MARS).
-
Cisco IPS (global correlation) is downloading lots of updates from the iron-port website
I have query on Global correlation.
Following is the observed behavior
Scenario 1:
Global Correlation Inspection: ON (Standard)
Reputation Filter: ON
Result: Global correlation downloads in bytes or KBs (observed on proxy)
Scenario 2:
Global Correlation Inspection: OFF
Reputation Filter: ON
Result: Global correlation downloads 4-5 MB every 5 Minutes (observed on proxy)
This behavior has been observed on both IPS devices one by one. What we wanted the clarity on is why is does global correlation download so much of data when it is OFF, and downloads only minimal data when ON. The equation does not seem to be right.
Request you for your prompt response.
Regards,
NealBoth global correlation and reputation filtering retrieve updates from the SensorBase network, or IronPort. By default, they communicate with the network every five minutes. This value cannot be changed by the IPS administrator.
-
Hi,
While enabling Global correlation, I understood that we need to configure proxy or DNS.
Also, I hope that needs to open the port (80/443) on the firewall for the management IP address of IPSto reach the cisco sensor database. If i'm correct what about the destination IP, do we need to enable "any" or specific IP is there.
ACL:
Source (IPS Management IP) -> Port (80/443) -> Destination?Hi,
Global correlation features only contain external IP addresses, so if you position a sensor in an
internal lab, you may never receive global correlation information.
Source (IPS Management IP) -> Port (80/443) -Detination is https://198.133.219.25//cgi-bin/front.x/ida/locator/locator.pl
Regards
Rajeswar -
ASA botnet filter vs ips global correlation
Does the global correlation include the data from botnet filter? On Cisc's site it says this on the global correlation
Customers deploying Cisco IPS can benefit from Global Correlation in multiple ways. First, bad traffic from known sources is stopped immediately. This includes zero-day attacks, for which no traditional threat prevention currently exists, advanced persistent threats (APTs), and botnet command and control trafficHello Matt,
Check the following info:
Cisco ASA Botnet Traffic Filter
This paper focuses on how Cisco Security Intelligence Operations relates to botnet threat identification, and its interaction with the Cisco ASA Botnet Traffic Filter. It is important to realize that a comprehensive security deployment should include Cisco Intrusion Prevention Systems (IPS) with its reputation based Global Correlation service and IPS signatures in conjunction with the security services provided by the ASA security appliance such as Botnet Traffic Filter.
So I would say they both provide you security based on databases from the SIO but they will not be equal on their funcionalities, that is why Cisco recommend to use both when possible,
Regards -
IPS 7.X Global Correlation in IME question
I was reading in the documentation for the new verison of IME that utilizes the new Global Correlation feature in IPS 7.X.
Quick question: Is the Global Correlation module a separate feature that has to be purchased? If so, do you license it for the IME or do you license it per sensor device? Would anyone be willing to share the cost?The Global Correlation feature is licensed on the sensor rather than IME, but is not a new license, it is the same license used for signature updates. So the Cisco Service for IPS contracts provide the license that works for both Signature Updates and Global Correlation Updates.
-
IPS Tech Talk -Global Correlation
Robert Albach of the Cisco IPS Team invites you to attend a Web seminar using WebEx. This event requires registration.
The event is a 30 minute webinar on Global Correlation - its operation and how it works with your Cisco IPS. Following the presentation there will be Question and Answer period with members of the IPS development team.
Topic: Cisco IPS Tech Talk 2010 Nov 18
Host: Robert Albach
Date and Time:
November 18, 2010 10:00 am, Central Standard Time (Chicago, GMT-06:00)
To register for the online event
1. Go to https://cisco.webex.com/ciscosales/onstage/g.php?d=204029379&t=a&EA=ralbach%40cisco.com&ET=6511931d5b5055f2311dc9824532002a&ETR=2c3560b429c7cfc0c2553092a899c175&RT=MiM3&p
2. Click "Register".
3. On the registration form, enter your information and then click "Submit".
Once the host approves your registration, you will receive a confirmation email message with instructions on how to join the event.
For assistance
You can contact Robert Albach at:
[email protected]Will this event be available for viewing later? 10am CST is about 1am here in Korea, so I don't think I'll be able to attend live.
-
Global-correlation does not update.
Hi all,
I have a problem to update the global-correlation. I do get updates for the signatures in the IPS but see output below regarding the global-correlation;
==========================================
show statistics global-correlation
Network Participation:
Counters:
Total Connection Attempts = 0
Total Connection Failures = 0
Connection Failures Since Last Success = 0
Connection History:
Updates:
Status Of Last Update Attempt = Failed
Time Since Last Successful Update = never
Counters:
Update Failures Since Last Success = 8
Total Update Attempts = 8
Total Update Failures = 8
Update Interval In Seconds = 300
Update Server = update-manifests.ironport.com
Update Server Address = 204.15.82.17
Current Versions:
config = 0
drop = 0
ip = 0
rule = 0
Warnings:
===========================================
Hardware used:
asa-ssm-10 (version 7.0(4)E4)
ASA-5520(version 8.4(1))
I see all traffic passing the firewall and ISP-routers.
I hope someone can help me with this issue or some pointers.
Thanks in advance,
Erik Verkerk.Hi Jennifer,
Good to hear we do not have to buy an additional license and that global-correlation is included in version 7.0.
Thanks for your suggestion "access to internet", I did a re-re-recheck of my configuration and found out that I had a "little routing issue in one of my routers". I solved this and now it is working.
===========================================
sh statistics global-correlation
Network Participation:
Counters:
Total Connection Attempts = 0
Total Connection Failures = 0
Connection Failures Since Last Success = 0
Connection History:
Updates:
Status Of Last Update Attempt = Ok
Time Since Last Successful Update = 2 minutes
Counters:
Update Failures Since Last Success = 0
Total Update Attempts = 269
Total Update Failures = 268
Update Interval In Seconds = 300
Update Server = update-manifests.ironport.com
Update Server Address = 204.15.82.17
Current Versions:
config = 1236210407
drop = 1300274962
ip = 1300276386
rule = 1300221126
Warnings:
=================================
Thanks for your time and help.
Thanks,
Erik Verkerk. -
Global correlation can't updated
version is IPS7.0, asa5520-aip-ssm.
Singatrue and IME can be sucessfully updated,
Global correlation can't updated,
the Status of global correlation is Critical.
I saw the website
http://www.cisco.com/en/US/docs/security/ips/7.0/configuration/guide/ime/ime_collaboration.html#wp1053280
and updated following the web page. But can't work it.
How could I update global correlation
or go back old sensorbase?The output provided clearly indicates that the AIP-SSM is unable to resolve the update server address. The server name update-manifests.ironport.com is not user configurable.
Do you have more than one DNS server configured? If so, disable all but the primary DNS server.
If you only have one DNS server configured, please verify the AIP-SSM's management IP address has unrestricted access to the Internet. (At a minimum TCP ports 80 and 443 and UDP port 53).
Scott -
Global Correlation Update Failures
I've recently turned on Global Correlation but we've failed to update every 5 minutes.
PL-ASA-IPS# show stat global
Network Participation:
Counters:
Total Connection Attempts = 2
Total Connection Failures = 0
Connection Failures Since Last Success = 0
Connection History:
Connection Attempt on February 16 2010, at 14:28:38 UTC = Successful
Connection Attempt on February 16 2010, at 14:19:06 UTC = Successful
Updates:
Status Of Last Update Attempt = Failed
Time Since Last Successful Update = never
Counters:
Update Failures Since Last Success = 4
Total Update Attempts = 4
Total Update Failures = 4
Update Interval In Seconds = 300
Update Server = update-manifests.ironport.com
Update Server Address = 204.15.82.17
Current Versions:
config = 0
drop = 0
ip = 0
rule = 0
Warnings:
I have a static NAT translation for the IPS, there are no proxy servers in our enviorment and it can ping outside as well as update-manifests.ironport.com (204.15.82.17). DNS is setup as well.
In the logs I see this entry:
16Feb2010 14:13:15.679 265.199 collaborationApp[491] rep/E A global correlation update failed: Failed download of ibrs/1.1/config/default/1236210407 : HTTP connection failed
I guess I'm at a loss for what else I can check. We have no problems sending the Network Participation data but we can't get any data. Any suggestions?
Cisco Intrusion Prevention System, Version 7.0(2)E3
Signature Definition:
Signature Update S469.0 2010-02-11
Virus Update V1.4 2007-03-02
OS Version: 2.4.30-IDS-smp-bigphysI have the same issue, i have no ASA or websense product between this device and the iNet.
Does anyone have a fix or workaround?
I have an AIM-IPS running 7.0(6)E4 with Signature versuon S599.0. All updates to date have been manualy d/l to a local ftp server
the auto update "seems" to run but never gets any updates
This is what i see
# sh stat global
Network Participation:
Counters:
Total Connection Attempts = 127
Total Connection Failures = 127
Connection Failures Since Last Success = 127
Connection History:
Connection Attempt on October 06 2011, at 10:46:32 UTC = Failed
Connection Attempt on October 06 2011, at 09:24:32 UTC = Failed
Connection Attempt on October 06 2011, at 08:03:04 UTC = Failed
Connection Attempt on October 06 2011, at 07:59:52 UTC = Failed
Connection Attempt on October 06 2011, at 06:36:57 UTC = Failed
Updates:
Status Of Last Update Attempt = Failed
Time Since Last Successful Update = never
Counters:
Update Failures Since Last Success = 2702
Total Update Attempts = 2702
Total Update Failures = 2702
Update Interval In Seconds = 300
Update Server = update-manifests.ironport.com
Update Server Address = Unknown
Current Versions:
config = 0
drop = 0
ip = 0
rule = 0
Warnings:
#sh ver
Application Partition:
Cisco Intrusion Prevention System, Version 7.0(6)E4
Host:
Realm Keys key1.0
Signature Definition:
Signature Update S599.0 2011-09-29
OS Version: 2.6.14-Cavium-Octeon
Platform: AIM-IPS-K9
Serial Number: xxx
Licensed, expires: 31-Mar-2012 UTC
Sensor up-time is 9 days.
Using 54726656 out of 454148096 bytes of available memory (12% usage)
system is using 22.4M out of 80.0M bytes of available disk space (28% usage)
application-data is using 46.8M out of 213.0M bytes of available disk space (23% usage)
boot is using 54.4M out of 114.8M bytes of available disk space (50% usage)
application-log is using 61.8M out of 513.0M bytes of available disk space (12% usage)
MainApp B-BEAU_2011_SEP_10_00_30_7_0_5_45 (Ipsbuild) 2011-09-10T00:32:09-0500 Running
AnalysisEngine B-BEAU_2011_SEP_10_00_30_7_0_5_45 (Ipsbuild) 2011-09-10T00:32:09-0500 Running
CollaborationApp B-BEAU_2011_SEP_10_00_30_7_0_5_45 (Ipsbuild) 2011-09-10T00:32:09-0500 Running
CLI B-BEAU_2011_SEP_10_00_30_7_0_5_45 (Ipsbuild) 2011-09-10T00:32:09-0500
Upgrade History:
* IPS-AIM-K9-7.0-6-E4 17:39:07 UTC Sat Sep 10 2011
IPS-sig-S599-req-E4.pkg 07:59:08 UTC Wed Oct 05 2011
Recovery Partition Version 1.1 - 7.0(6)E4
Host Certificate Valid from: 25-Sep-2011 to 25-Sep-2013
>
as seen above there is no ip address listed for "update-manifests.ironport.com"
NS lookup is able to resolve,
why can't the IPS?
I can i hard code the ip address?
>Non-authoritative answer:
>Name: update-manifests.ironport.com
>Address: 204.15.82.17 -
Global Correlation and Application Failed
Hi, People.
I have IPS4270-20-K9 with version 7.0(3)E4 and signature version 572.
In Sensor Health show me a problem critical, with:
- Application Failed
- Global Correlation
sensor#sh statistics global-correlation
Error: getGlobalCorrelationStatistics : ct-collaborationApp.459 not responding, please check system processes - The connect to the specified Io::ClientPipe failed.
How do I resolve these problems?
Tks.That error message indicates that one of the software processes required for the Global Correlation feature (CollaborationApp) is not responding (stopped/crashed, hung, etc.). You will need to reboot ("reset") the sensor to restore the process to a "Running" status.
There are multiple defects present in the version of software you are running (7.0(3)E4) that are likely culprits/causes that were fixed in subsequent releases (7.0(4)E4 and 7.0(5a)E4). After you have rebooted the sensor and restored it to service, you can upgrade to a fixed release (7.0(5a)E4). -
"Global Correlation" = Critical - Cisco AIP-SSM-20
We are getting this error on both IME and IDM. What causes this, and how does one resolve it?
We are also not getting new events in IME - could this be related to the problem?correct..The sensor must operate in Inline mode so that the Global Correlation features can increase efficacy by being able to use the inline deny actions.
http://www.cisco.com/en/US/docs/security/ips/7.0/configuration/guide/ime/ime_collaboration.html
Maybe you are looking for
-
Help with Ruby on Rails and mysql - I just don't get the terminal...
Let me just start by saying I'm pretty new to using the terminal and unix commands. I've been trying to teach myself how to use Ruby on Rails (ror) over the pasy couple of days and have had some luck but I'm struggling with the terminal. For instance
-
SAP EP 7.0 in Windows XP Pro
Hello everybody, here is my question. I want to install SAP Enterprise Portal 7.0 (Netweaver 2004s platform) with its collaborative tools like TREX and KM and its WAS in Windows XP Professional. Is this possible? Has anyone installed this? Thanks a l
-
How do I get videos to play through without stopping and starting
-
#1 I went to http://forums.verizon.com/ #2 I clicked on Sign On. #3 I was sent a URL starting with HTTP, then a URL starting with HTTPS, and then a URL Starting with HTTP. I am just wondering... Is this happening for anyone else? Please and thanks. P
-
Running Microsoft Script Editor after installing Office 2010
As per this link: http://office.microsoft.com/en-us/excel-help/use-office-excel-2010-with-earlier-versions-of-excel-HA010342994.aspx Microsoft Script Editor is installed along with Office 2010, even though it cannot be accessed from the UI. However,