IPS network Module, need help!!!

Folks,
I recently installed IPS network module in my 3662 router. I am having problems making the IPS log anything.
When i access the web interface of the IPS, i see only 1 interface available under virtual sensor, the interface is fast 0/1. and the media type it shows is Backplain.
I am confused, i thought that fast 0/1 on the IPS network module was the management interface??? on the IPS?
Why don't i see another interface that is connected to the backplain of the switch???
Many thanks

There are 2 interfaces on the NM-CIDS.
In version 5.0 they are called:
FastEthernet0/0 and FastEthernet0/1
FastEthernet0/0 is the external copper interface that you can plug a cable in to. It is the command and control port for managing the NM-CIDS. It can not be used for monitoring (can not be applied to the virtual sensor)
FastEthernet0/1 is the backplane interface. It receives packets from the router for monitoring. This is the interface that should be applied to the virtual sensor.

Similar Messages

HT4623 want to unlock iphone to other network providers need help

trying to unlock iphone so i am able to use any other network but ive tried and i just cant seem to do it does anyone know other ways of unlocking the phone need hel please

The only ones who can unlock your iPhone is your phone company/carrier.
You need to contact them and if they offer unlocking for your phone then ask them to unlock it and if they don't, there is nothing you can do. In this case, you either need to purchase another phone that is fully and officially unlocked or you need to continue to use your phone with your current operator.
Contact your phone comapny/carrier directly - they are the ONLY ones who can help you.

Trying to connect to xbox live using my home network, I need help.

I have a xbox 360 that I want to connect to xbox live with, using my home network. Every time I try to connect to xbox live the only part that fails is the connecting to xbox live part. This is how my network is set up. I have Cox Cable as my ISP, a Linksys WCG200 gateway(v2), and WRT54GS(v7). The cable wire is connected to the WCG200 gateway, then an Ethernet cable connects the gateway to the WRT54GS router, and finally an Ethernet cable connects the router to my xbox 360. I have contacted Cox, Linksys, and Microsoft about the situation and they all say the problem is the version of the router. Someone told me that I may just need to change the firmware, but I don't know how to do that. If anyone could tell me what the problem is and hopefully how to fix it, it would be much appreciated.

u might to open port numbers 88 and 234 on your router
here's how to open ports
1: open IE and on the address bar, type in 192.168.1.1 and hit enter
           USERNAME: ( leave it blank )
           PASSWORD: admin ( all in lowercases )
2: click on the tab " applications and gaming "  then click on the SUBTAB port triggering.
3: you can just name the application like, box or whatever and fill in 88 for each of the boxes in the first line
4: same goes to application number 2 but you have to put 2304 for each of the boxes and pls do not forget to enable it, then save settings
5: Teset the xbox if it's now working.
6: if still not working, go to the SECURITY tab and uncheck the bock that says, " block anonymous internet requests and save settings.
7: teset xboox agan and if it still won't work
8: go to the SET UP tab and look for MTU.
9: set it to manual and lower down the size by 10.( by default, it's 1500. )→ save settings.
          Hope it will help. goodluck!

Guest ldom network issue - Need help please

I have a T4-4 sparc server and the SO is Solaris 11...
We have 2 Qlogic/Sun FcOE 10Gb cards
Network is configured as follows:
1. The two ethernets are aggregated
2. Created Vlana dn have vlan id
3. vswitch is presented to the guests as vsw0 and vsw1.
After configuring the guest's network, guest can not reach the default gateway.
Any help is appriciated. ( all the guests are Solaris 11)

We'll need some data... Could you please post the output from the following commands (in the control domain):
ldm -V
ldm list
ldm list -l
ldm list-services
And from both guest domains and the control domian, please issue:
dladm show-phys
dladm show-link
ipadm show-if
ipadm show-addr
netstat -r
ifconfig -a
That will show the network configuration so we can see what's up. Also - did you plumb the vsw onto the physical interface? That was done with Solaris 10 control domains, but is no longer needed.
regards, Jeff

Hp laserjet 4015 network issue need help

hello and sorry if you all seen this already, i did this post yesterday but its not showing up and my info is not showing i did the post.
ok here's the deal. i have a hp laserjet p4015n printer. right now its connected to a network and every pc thats on the network can see it and print to it etc.
however the current internet package is too expensive and i am planning on doing away with the current provider and goign with a different one. but i have to give them back the equipment.
so i am trying to get everything set up before i do that and i am having problems.
i can get everything else working just fine regardless of what router i use and on both the old slower brother printer is found and can print just fine but the hp printer refuses to be recognized.
i have two routers i have tried this with
a belkin n600
linksys wrt54g
with the linksys router when the printer is connected to it it shows as a device is connected as the light lights up solid but nothing i do can get the printer installed.
i can not ping the route either.
its connected to the router via an ethernet cable
the pcs on the network mostly use win 7 but one is using windows vista but none can install the printer.
i've tried installin gusin ghte host name and ip address
tried using hp's installation software but it just don't find the printer.
this is all driving me nuts and any help would be greatly appreciated.
thanks
ryan

I am sorry, but to get your issue more exposure I would suggest posting it in the commercial forums since this is a commercial printer. You can do this at Printers - LaserJet. Click on New Post.
I hope this helps.
Please click “Accept as Solution ” if you feel my post solved your issue, it will help others find the solution.
Click the “Kudos Thumbs Up" on the right to say “Thanks” for helping!
Gemini02
I work on behalf of HP

I setup a Cisco Home Network and Need help Logging into It

Hello, I have four 2521 routers and three 2954 switches. I connected my ISPs modem from the ethernet port and plugged it into port 24 of one of my switches. I also configured the switch for VTY access and gave it a login password. I would like to log into the switch to configure it and telnet into all the other devices from a remote location. But I am unable to ping the public address assigned to me by my ISP. So I can't even telnet to the switch. Help

With help from elsewhere, I have learned how to change the colors and figured out a few other things. I have another question, though.
I want to put a Twitter widget and a comment box on my website. I have the widget code from Twitter, but it is HTML and javascript or something. Can I just put these codes into the modules of the flash template? If you look at the template, you should see that it has modules that have editable HTML text areas, but I don't know if it is limited to text or something, or if it will function correctly if I put other HTML codes in it such as script codes, etc in it.
Also, if that works, does anyone know where I can get a code to put the comment box in one of the modules? I don't mean a contact box, I mean a widget where people can leave comments and the comments display on the page, like on a myspace profile. Just something simple that allows a visitor to leave a name and a text-only comment. I would also like to be able to selectively delete comments in case of spammers, etc.
I found this, which might be what I am looking for, just a simple comment box, but this one is flash:
http://activeden.net/item/commenting-with-no-database/69183?sso?WT.ac=search_item&WT.seg_1 =search_item&WT.z_author=flashBrian
Message was edited by: ESJoeProductions

Faulty Bluetooth Module, Need Help to Completely Disable

I have a 2 GHz Core Duo Macbook running 10.6.8 and I am currently having a very frustrating issue with my bluetooth module. When I attempt to sleep my computer it immediately wakes, as addressed by users with faulty bluetooth modules. Bluetooth is also not found in my system profiler so it must be a hardware issue. At this point I am just holding out for a the new macbook pro and am trying to get by with this machine. My question is how can I completely disable bluetooth on my computer so that my mac will not sleep. I do not have any bluetooth devices and am not concerned about regaining bluetooth functionality, I just want my computer to get some sleep. I am familiar with basic terminal commands.

Hi, manojgj
I don't think the wire is part of the Bluetooth. If you enter the BIOS and navigate Security ► I/O Port Access, do you see Bluetooth listed? If so, is it set to Enabled?
Best,
Adam
Did someone help you today? Press the star on the left to thank them with a Kudo!
If you find a post helpful and it answers your question, please mark it as an "Accepted Solution!" This will help the rest of the community with similar issues identify the verified solution and benefit from it.

Network Settings: Need Help!

Hi people,
I have an older iMac I'm playing with.
I have a Verizon FiOS connection, but am using airport to connect to Verizon's router. (There are two other computers using this network).
On my other systems, my duplex setting is always at half duplex.
But on this machine and this Verizon router, my Duplex setting always reverts to Full-Duplex.
Is this a problem that slows my system down? Or is this the correct setting for Verizon's Routers?
Any help or advise would be greatly appreciated.
Walt.

Full duplex is faster than half duplex. It has nothing to do with your particular router. Duplex is part of the communications protocols. See this article.

Im from the philippines and i cant accesd my sociasl networking sites need help

how do i get configuration setting for my bb 9300 ? my telco is smart

Hiya!
You're going to need to be more specific. What exactly are you not able to access? what happens? has it ever worked? can you access the internet? do you get any errors?
If you cannot access the internet at all on your phone, chances are you do not have the correct data plan on your account and you should contact your carrier for assistance.
cheers!
1). Please thank those who help you by clicking the beside the 'Reply' button.
2). If your issue has been solved, please resolve it by marking "Accept as Solution" on the correct post!
3). Remember to have fun! We are all in this together!
4). Follow me on

Newb here has been put in charge of a small company network. Need help!

I'm new to ARD, but well versed in Macs and OSX. A friend's family has a small company and the head honcho uses ARD to monitor the other Macs at the office from her iMac running 10.6.3 there at the office, as well as from home using another iMac and a Macbook Air. I was asked to help and am well paid to figure out ARD for them. They booted their last IT guy, by the way. So the boss's Macbook Air and her Office iMac are the Administrators, and the iMac at home is the client. All machines running 10.6.3 and latest ARD 3.3.2 Admin and Client s/w.
For whatever reason I can only control or watch the office iMac from the iMac at home, and cannot access the home iMac from the office.
For the record, the Macbook Air does not have this same issue, but I've yet to tackle it.
When I double click the office iMac from the Home iMac and look through the tabs, I am told the Client s/w on that office iMac is an old version.
I have read the white papers and watched the Apple videos. This just doesn't make sense!
What is going on? Any hints? Please......

FIXED! However........
The home iMac "supposedly" has a fixed IP address. Well, it wandered a bit apparently so there was a small change at the ISP that threw everything off. I looked into an email sent from that machine's user and displayed the long header to get the IP address of the home iMac. I then entered that new IP address into ARD from the office iMac, and BAM, works like a charm now!
What I can't figure out is why the ARD on home iMac says the office iMac is running 10.5.8, when it is running 10.6.3 and it also says the office ARD client is 3.2.X rather than the actual 3.3.2 it is indeed running. Weird?
Any ideas? Maybe everything will update once I use ARD from the home iMac into the office iMac?
Message was edited by: Alex Einspruch
Message was edited by: Alex Einspruch

PM Module needs help

Hi,
I wish to know about how Preventive Maintenance Schedule will happen with different dates and multiple equipments under One Maintenance Plan assighining
different Maintenance items to each equipment.Scheduling period is one year. I can give different start of cycle dates to each equipment.
S.Shridhar

hi
shridar you cannot give different dates for different maintenance items since it is covering using maintenance plan ,every item will have the same start date
for detailed procedure have alook here
http://help.sap.com/saphelp_47x200/helpdata/en/b0/df293581dc1f79e10000009b38f889/frameset.htm
and select maintenance plan under preventive maintenance heading
regards
thyagarajan

Airport will not connect to my home network after trying to connect to my school's network. Need help!

Airport on my Macbook will no longer connect to my internet network at home. I was on campus using my university's network today and now Airport only wants to connect to it and will not change back to my home network. It has something to do with the 802.1X, and I don't know enough about networks to know what that does. Is there someway I can just reset my entire airport settings to where it would be like the first time I used my Macbook and configured it to my home network?

Is there someway I can just reset my entire airport settings to where it would be like the first time I used my Macbook and configured it to my home network?
Did you Shut Down the Mac and then power it back up? Can you connect to your home network now if you click the fan shaped AirPort icon at the top of the Mac's screen?
If your home network name does not appear, click Join Other Network, then click Show Networks.
Click the name of the network that you want to join and enter the password if required
Are you saying that you want to delete the connection to the school network from your Mac? If you do this, you will have to setup the connection again if you head back to the school.

Need help about Hidden Markov Model model

I want to make classification for EEG signal using Hidden Markov Model
algorithm based on neural network.
plz need help about how to implement this algorithm using LABVIEW.
if not I want another thing to make classification.
any one know information about this topic, send me a reply
thanks

Have you derrived the HMM that you want to implement?
If so, post the algorithm and we can provide comments on how to implement it using LabVIEW.
Message Edited by Ray.R on 04-12-2010 12:54 PM

Need help. thank you

How to using ovi store connect via wifi for my nokia n8?
the ovi store kept connect automatically using mobile network?
need help thnak you

ohh. Thanks for the suggestion.
I already set my wifi to priority 1, but it still won't work.
it kept using my mobile network. i think there is no problem with my wifi connection

Need help adobe bridge cc output module

I need help. I have an assignment I'm held up on completing because the adobe cc bridge does not have the output modue I need. I followed the adobe instructions page to the letter. I copied and pasted the output module folder to the adobe bridge cc extensions folder in programs/commonfiles/adobe. The only thing is the instructions then say to paste the workspace file into the workspace folder located below the bridge extensions folder. I don't have a workspaces folder there or anywhere. I even tried must making one and adding the file to it, but no go. can someone PLEASE help me with this? I have an assignment due like now that requires the use of the output modue.thanks!

oh,my system is windows 8.1. sorry, lol.

IPS network Module, need help!!!

Similar Messages

Maybe you are looking for