IPS status LED stays red
Dear Friends,
There is a IPS 4260 that reports the status LED to red. When reading the hardware installation guide, i came to know that this indicates a POST failure. I forced a POST again of the IPS by rebooting the IPS but i could not capture any significant error.
However, i am enclosing the captures of the boot process (Filename: IPS) and the sh tech-support (Filename: IPS Tech support).
Can you please help me on this?
Thanks a lot
Regards
Gautam
Shutdonw the IPS for 5 - 10 Minutes and the Restart i did and the issue has been resolved .
Thanks,
Mustafa
Similar Messages
-
While turning on the system the status led stay on. Doing this few time, now the Status led doesn’t stay on but it seems that the controller doesn’t make the booting procedure (the Leds doesn’t turn on and off at the begging)
This issue can generally be solved by formatting the internal Compact FLASH memory on the controller. There is a < a href="http://digital.ni.com/public.nsf/websearch/6D0F9F74FD2DAD0186256EE5007198D4?OpenDocument">Knowledge Base that describes in detail how to format the controller. Sometimes you will first have to switch both the Safe Mode (switch 7) and Reset IP (switch 8) dip switches and cycle the power to first get the controller into a safe state.
The Compact FLASH corruption is generally due to losing power while writing to a sector on disk. This can cause that sector as well as other adjacent sectors to become corrupt. -
CFP status led - stays lit solid red!
Hi,
I have a problem with a cFP-2120 RT controller where the red LED status light stays lit. On the instruction manual it says that the unit was not powered up correctly and to contact NI. The controller used to work fine until we had a short on the mains side of the power supply The AI, AO and thermocouple modules did not power up but the DI and DO modules seemed to be getting power. Is there anything we can do or just send it back for repairs. When I replaced the controller with another one, the system worked fine and the status LED turned off after a few seconds.
rgds
Inzaghi_2Sounds like you've proven that the controller is bad. Next step is an RMA from NI. Make sure NI tells you what failed in the controller and see if they will comment on what might have caused it. The idea being to see if you can do anything to prevent this failure in the future.
-
Sup V with 4507R status led in Red
Hi,
I carried out an upgrade in 4507R with 2 sup V, I loaded in both card 12.2(53)SG10 and I confirmed the redundancy is working
I don't understand why both status led (for Sup V) are in red.
the loggs do not show error , any idea how can I identify the reason of red color in status led?
regards
Mod Redundancy role Operating mode Redundancy status
----+-------------------+-------------------+----------------------------------
1 Standby Supervisor SSO Standby hot
2 Active Supervisor SSO Active
redundancy
mode sso
main-cpu
auto-sync standardHello,
The status LED can actually lend useful information regarding the potential culprits to your issue. You can check out the STATUS LED Error Indications in the 1601 User Manual.
In this case, it looks like you should contact National Instruments directly since it seems as though the module did not power on correctly. You may have to return your unit for replacement or repair.
Cheers,
Emilie K. | Applications Engineer | National Instruments -
FP 1601 status led shows red continuously
I am trying to use FP 1601 which was already configured long before. But now the status LED is continuously red .Power LEd is green and all other LEds are off. Am giving 24V power and checked that it is given to V and C properly .Ethernet connection is also proper. i tried to reset , but could not. i cant use it in anymore. can anyone help in troubleshooting
Hello,
The status LED can actually lend useful information regarding the potential culprits to your issue. You can check out the STATUS LED Error Indications in the 1601 User Manual.
In this case, it looks like you should contact National Instruments directly since it seems as though the module did not power on correctly. You may have to return your unit for replacement or repair.
Cheers,
Emilie K. | Applications Engineer | National Instruments -
AEBS: Status LED stays green even if modem unplugged?
I recently updated to 7.6.3. and since than have had loads of problems. I'm not sure if it's just coincidence or if they are 7.6.3. related. Problems included difficulty connecting to internet, slow wifi speeds and being unable to see the AEBS under Airport Utility on a Macbook (Mountain Lion 10.8.2) unless the device and Mac were rebooted. It would often then dissapear again. I've resolved most of those now by going back to 7.6.1. There is one more issue that I've noticed though that didn't seem to happen before.
Essentially, amidst all the testing and rebooting I was doing I noticed that when the modem (handling the PPPoE with the Airport in bridge mode - forced to this because my ISP does not play nice with Apple's PPPoE authentication) was unplugged or powered down, the green status light on the airport stayed on? I'm sure it never did this before, indeed I've seen the amber light on when there have been ISP outages. One thing I haven't tried yet is leaving the modem off for an hour or so to see if that prompts a change to amber.
As yet I haven't done another full factory reset (albeit one was done to get it all working again).as I've wasted two days with the 7.6.3 update and needless to say I need a break from the thing!!! Just strikes me as odd that despite the internet light on Airport Utility on all the devices shows amber when the ethernet cable is unplugged from the modem yet the green light on the BS stays on AND, under Aiport Utility 5.6 it shows a green light against the airport saying status is 'Normal'?
Surely this should not be happening? No internet, amber light on AEBS I would have thought?Thanks. I'll have a look maybe over the weekend. I know resets are not that complex (albeit I did have loads of problems getting the AEBS to even show again when I did a reset under 7.6.3 when the problems started) but I spent so long sorting the mess out I need to get on and do things ON the internet for a couple of days, rather than trying to get it working LOL!!
I notice you say AU 5.6.1, the version I have other than 6 is 5.6. That wouldn't be causing any issues would it. One thing I did try to do when it was all completely screwed is use 5.6 to configure manually. I now seem to have various .XML profiles under
User/Library/Application Support/Apple/Airport/Configuration
My undesrtanding is that AU doesn't work this was and that these folders/files shouldn't be there? Maybe I'm wrong? Are they just profiles under my user name that won't be affecting anything. Or could they be interfering with AEBS operations and / or warnings in any way. Is the AEBS confused? I was tempted to delete the entire airport folder altogether or even just the config settings then do a factory restore of the AEBS under 5.6. Trouble is I'm not sure which AU Airport folder above belongs to (e.g. will it screw things up further if I delete any or all of it). Bit of a mess really
Yes the settings you mention are correct, the IP addess even picks up at 101, the resrved address on the router. -
Blackberry Pearl 8100 randomly shuts off and the status LED flashes red
My pearl was reciently unlocked and changed from AT&T service to t-mobile. after this switch the pearl started having fits of rage where it will turn off randomly, weather any keys have been hit or even if it is idle. the device LED then flashes red, sometimes once, other times it will flash once every 4 seconds for hours. then it will randomly turn back on either to the exact screen it had been on before it powered off or it will reboot completley and start the normal start-up procedure and varify security checks just as if the battery were removed. i tried removing the batery and leaving the phone disassymbled for a few nights but in the morning the plague is back and unrelenting. sometimes all i have to do it pick the device up and it will shut off. other times i will be plugging away with it for 20 or so minutes on the internet and then it will die suddenly. it also cuts out in the middle of phone calls. if anyone can help,please let me know.
blackberry 8100 v4.2.1.96Is it a new phone? If it's less then a month old see if you can return it, otherwise you can try reloading the OS.
So if you're willing to try that, do the following.
First download and install the Desktop Manager from here (4.6 without Media Manager is recommended): https://www.blackberry.com/Downloads/entry.do?code=A8BAA56554F96369AB93E4F3BB068C22
Next you can use the Backup and Restore feature present in the software to make a backup of all the data on your phone.
Next download and install the handheld software from here: http://na.blackberry.com/eng/support/downloads/download_sites.jsp
Afterwards try reloading the OS by connecting the device to your computer, open the Desktop Manager, then go into the Application Loader. This will open a wizard that steps you through reloading the OS onto your device. More detailed steps can be found here:
http://www.blackberry.com/btsc/KB03485
If someone has been helpful please consider giving them kudos by clicking the star to the left of their post.
Remember to resolve your thread by clicking Accepted Solution. -
hi,
I have a Cisco AIR-LAP1131AG-E-K9 when I boot one accesspoint it gives Ethernet LED = Off; Radio LED = RED ; Status LED = RED and only next listing in the screen:
Xmodem file system is available.
Flashfs[0]: unable to allocate available block.
The system has been interrupted, or encountered an error during initializion of the flash filesystem.
The foolowing commands will initialize the flash filesystem, and finish loading the operating system software:
flash_init
ether_init
tftp_init
boot
When I type this commands, it doesn't help at all. The output will be following:
ap: flash_init
Initializing Flash...
flashfs[0]: out of memory
...done Initializing Flash.
ap: ether_init
Initializing ethernet port 0...
Reset ethernet port 0...
Reset done!
ap: tftp_init
Unable to get our ip address: no "IP_ADDR" variable set
ap: boot
Loading ""...; permission denied
Error loading ""
Interrupt within 5 seconds to abort boot process.
Boot process failed...
ap:
what i do ? please help , thanksDuplicate posts.
Go here: http://supportforums.cisco.com/discussion/12154826/problem-cisco-air-lap1131ag-e-k9-ethernet-led-radio-led-red-status-led-red -
MDS 9216 - showing red status LED, not starting up
Hi,
In a recent power loss (took out our R&D UPS in the process), an MDS 9216 we have in R&D failed.
On power up, it shows a red status LED, and does nothing. We've pulled and swapped PSUs (something we're told is a common fix for a common problem with these chassis), to no avail.
Strangely, we pulled the fan card (which had a green light), and put it back in to see it now also has a red status light.
We've swapped all cards around for new and spares (even the main cards) and they show up with red status lights in the chassis (can't test them in another chassis at present) so I assume this problem is with the chassis itself (ie the backplane or PSUs).
Any ideas, any similar experiences?
Many thanks,As far as warranty, it would be covered for 1 year or 90 days from purchase....not sure which, but since the 9216 is end of sale for a few years now, I doubt that is covered under warranty. If you have a maintenance contract covering that 9216 serial number, then it would be covered. The design on the 9216 is that the module 1 is not field replaceable. There is no Cisco part number for the slot1 line card. It is a hybrid of a 16 port FC module with a supervisor daughter card. It is basically considered part of the chassis. If you have your own spare 9216 and feel energetic you could replace the slot 1 line card....but from the official support perspective, it is not replaceable.
There are no other replaceable parts besides the chassis and PS that would cause this problem. (I assume you have removed any line card from slot2 to be sure it was not causing the problem).
Thanks,
Mike -
CIsco AIR LAP1131AG E K9 Status LED = Yellow; Ethernet LED = Off; Radio LED = blinking Red in a pattern, red off then red red, Our AP isn't working it won't show up on our Cisco WLC 2125 anymore and this is the LED indicators, I've checked in the manual and this combination of LEDs do not exists??
No cisco web is working perfectly.
do you have a valid CCO id with smarnet contract ?? then only you can download new IOS for AP:
Autonomous AP image:
http://software.cisco.com/download/release.html?mdfid=279537722&flowid=6775&softwareid=284180979&release=12.4.25d-JA2&relind=AVAILABLE&rellifecycle=ED&reltype=latest
LAP AP image:
http://software.cisco.com/download/release.html?mdfid=279537722&flowid=6775&softwareid=280775090&release=12.4.25e-JAP&relind=AVAILABLE&rellifecycle=ED&reltype=latest
Regards -
FP2000 status light stays lit red can not communicate
I just tried to update the software on a FP2000 not the status light stays read and can not communicate. any ideas.
Solved!
Go to Solution.TJE-
Based on the manual for this device, the status light staying lit refers to “the FieldPoint-20XX did not power on correctly.” I would suggest removing all software from this controller and reinstall it.
Regards,
Mike S
NI AE -
NI smart camera 1764 Status LED Blinking
I am using NI smart camera 1764. when i am giving 24 V DC supply to the camera then Power & Status LED is blinking continuously in RED colour. on the other hand pass & fail LED also blinking in RED & GREEN colour alternatively. i am not able to connect camera to my computer through ETHERNET cable & cannot use for my application.
Please suggest me the solution as soon as possible.Have a look at chapter 6 of this manual:
http://www.ni.com/pdf/manuals/372429b.pdf
Adnan Zafar
Certified LabVIEW Architect
Coleman Technologies -
LED constant red after opening SMS message
Hi, i have the blackberry pearl 8100, i had a difficulty with this before bu after upgrading it would not flash the LED it would flash if not open but once open and sent it would stay red.. howcan i fix this?
Welcme to the Frums!
Try removing your battery. Replace after 30 seconds - allowing your phone to reboot.
Nurse-Berry
Follow NurseBerry08 on Twitter -
Cisco 1131AG LWAP status led yellow and other leds blinking green
I have a problem with three AIR-LAP1131AG-E-K9 that joined the controller and the status led turns to yellow after joining the controller while other LEDs are blinking green.
The APs has no coverage at all although the WCS shows that there is coverage and the 4400WLC shows that the AP interfaces are UP. (The ethernet interface and tha 802.11b,g radio interface is up).
The SSID broadcast is enabled.
On the switch the interface is up and there is traffic going in and out of the LAP.
I tired power reset and factory reset for the APs but the problem remains the same.
Any ideas for what might be the problem ?!!
RegardsYes the clients are not able to see the SSID broadcasted by the AP.
But these APs were functioning normally before without any changes to the WLC config.
I had the same problem with other APs but they went back to normal state after a hardware reset to the APs. -
WiSM Status LED 1 & Status LED 2 showing off. Is it normal?
Hi,
WiSM WLAN Service Module WS-SVC-WISM-1-K9 in 6509e running VSS IOs s72033-ipservicesk9_wan-mz.122-33.SXI2a.bin having trouble to get the IP from service-vlan DHCP also status LED 1 & Status LED 2 showing off.
The pertinent config is as follows.
vlan 300
name WiSM_Service_Vlan
interface Vlan300
description *** WiSM Service-Vlan
ip address 192.168.200.1 255.255.255.0
ip dhcp excluded-address 192.168.200.1
ip dhcp pool WiSM_Service-Vlan_300
network 192.168.200.0 255.255.255.0
default-router 192.168.200.1
wism service-vlan 300
vlan 183
name WiSM_Management
interface Vlan183
description *** WiSM Management Vlan ***
ip address 10.39.139.254 255.255.255.0
wism switch 1 module 4 controller 1 allowed-vlan 125,126,183,300
wism switch 1 module 4 controller 2 allowed-vlan 125,126,183,300
wism switch 2 module 4 controller 1 allowed-vlan 125,126,183,300
wism switch 2 module 4 controller 2 allowed-vlan 125,126,183,300
wism switch 1 module 4 controller 1 native-vlan 183
wism switch 1 module 4 controller 2 native-vlan 183
wism switch 2 module 4 controller 1 native-vlan 183
wism switch 2 module 4 controller 2 native-vlan 183
HO2NET0001#sh wism status
Service Vlan : 300, Service IP Subnet : 192.168.200.1/255.255.255.0
WLAN
Slot Controller Service IP Management IP SW Version Status
----+-----------+----------------+----------------+-----------+---------------
20 1 0.0.0.0 0.0.0.0 Service Port Up
20 2 0.0.0.0 0.0.0.0 Service Port Up
HO2NET0001#sh module
Mod Ports Card Type Model Serial No.
1 8 CEF720 8 port 10GE with DFC WS-X6708-10GE SAL13442Q5N
2 8 CEF720 8 port 10GE with DFC WS-X6708-10GE SAL13442GAL
3 48 CEF720 48 port 10/100/1000mb Ethernet WS-X6748-GE-TX SAL13410N8P
4 10 WiSM WLAN Service Module WS-SVC-WISM-1-K9 SAD133101UY
5 5 Supervisor Engine 720 10GE (Active) VS-S720-10G SAL13442JE4
Mod MAC addresses Hw Fw Sw Status
1 0025.84f1.55b8 to 0025.84f1.55bf 2.1 12.2(18r)S1 12.2(33)SXI2 Ok
2 0025.84f1.4e58 to 0025.84f1.4e5f 2.1 12.2(18r)S1 12.2(33)SXI2 Ok
3 0027.0da7.c240 to 0027.0da7.c26f 3.2 12.2(18r)S1 12.2(33)SXI2 Ok
4 0023.5e25.7168 to 0023.5e25.7177 2.3 12.2(14r)S5 12.2(33)SXI2 Ok
5 001f.9e2a.2608 to 001f.9e2a.260f 3.1 8.5(3) 12.2(33)SXI2 Ok
Mod Sub-Module Model Serial Hw Status
1 Distributed Forwarding Card WS-F6700-DFC3C SAL13442EG9 1.4 Ok
2 Distributed Forwarding Card WS-F6700-DFC3C SAL13442H9T 1.4 Ok
3 Centralized Forwarding Card WS-F6700-CFC SAL13442HU9 4.1 Ok
4 Centralized Forwarding Card WS-SVC-WISM-1-K9-D SAD133200D6 2.1 Ok
5 Policy Feature Card 3 VS-F6K-PFC3C SAL13442E5S 1.1 Ok
5 MSFC3 Daughterboard VS-F6K-MSFC3 SAL13421AJZ 2.0 Ok
Mod Online Diag Status
1 Pass
2 Pass
3 Pass
4 Pass
5 Pass
HO2NET0001#sh vlan
300 WiSM_Service_Vlan active Gi1/4/9, Gi1/4/10
The service IP is supposed to have been populated with an address from the dhcp pool. I am also unable to connect to access it by console as well as doing a session switch 1 slot 4 processor 1. I get the following upon attempting to do so:
Through Console.
It is giving following & then got stuck.
Bootloader 3.2.202.0 (Nov 13 2007 - 19:35:12)
Motorola PowerPC ProcessorID=00000000 Rev. PVR=80200020
CPU: 999 MHz
CCB: 333 MHz
DDR: 166 MHz
LBC: 41 MHz
L1 D-cache 32KB, L1 I-cache 32KB enabled.
I2C: ready
DTT: 1 is 33 C
DRAM: DDR module detected, total size:512MB.
512 MB
8540 in PCI Host Mode.
8540 not PCI Arbiter.
Memory Test PASS
FLASH:
Flash Bank 0: portsize = 2, size = 8 MB in 142 Sectors
8 MB
L2 cache enabled: 256KB
Card Id: 1537
Card Revision Id: 1
Card CPU Id: 1287
Number of MAC Addresses: 32
Number of Slots Supported: 4
Serial Number: FAM133200D6
Manufacturers ID: 30464
Board Maintenance Level: 00
In: serial
Out: serial
Err: serial
.o88b. d888888b .d8888. .o88b. .d88b.
d8P Y8 `88' 88' YP d8P Y8 .8P Y8.
8P 88 `8bo. 8P 88 88
8b 88 `Y8b. 8b 88 88
Y8b d8 .88. db 8D Y8b d8 `8b d8'
`Y88P' Y888888P `8888Y' `Y88P' `Y88P'
Model SVC-WiSM S/N: FAM133200D6
Net: TSEC ETHERNET
IDE: Bus 0: OK
Device 0: Model: STI Flash 8.0.0 Firm: 01/17/07 Ser#: STI1MMJ109198093647
Type: Removable Hard Disk
Capacity: 488.7 MB = 0.4 GB (1000944 x 512)
Device 1: not available
Booting Primary Image...
Press <ESC> now for additional boot options...
Detecting Hardware . . .
Cryptographic library self-test....passed!
XML config selected
Validating XML configuration
Cisco is a trademark of Cisco Systems, Inc.
Software Copyright Cisco Systems, Inc. All rights reserved.
Cisco AireOS Version 5.2.178.0
Initializing OS Services: ok
Initializing Serial Services: ok
Initializing Internal Interfaces: ok
Initializing Network Services: ok
Initializing Licensing Services: ok
Starting ARP Services: ok
Starting Trap Manager: ok
Starting Network Interface Management Services: ok
Starting System Services: ok
Starting FIPS Features: ok : Not enabled
Starting Fast Path Hardware Acceleration: ok
Starting Switching Services: ok
Starting QoS Services: ok
Starting Policy Manager: ok
Starting Data Transport Link Layer: ok
Starting Access Control List Services: ok
Starting System Interfaces: ok
Starting Client Troubleshooting Service: ok
Starting Management Frame Protection: ok
Starting LWAPP: ok
Starting CAPWAP: ok
Starting Certificate Database: ok
Starting VPN Services: ok
Starting Security Services: ok
Starting Policy Manager: ok
Starting Authentication Engine: ok
Starting Mobility Management: ok
Starting LOCP: ok
Starting Virtual AP Services: ok
Starting AireWave Director: ok
Starting Network Time Services: ok
Starting Cisco Discovery Protocol: ok
Starting Broadcast Services: ok
Starting Logging Services: ok
Starting DHCP Server: ok
Starting IDS Signature Manager: ok
Starting RFID Tag Tracking: ok
Starting WLAN Control Protocol (WCP): ok
Starting Mesh Services: ok
Starting TSM: ok
Starting CIDS Services: ok
Starting Ethernet-over-IP: ok
Starting DTLS server: enabled in CAPWAP
Starting FMC HS: ok
Starting WIPS: ok
Starting SSHPM LSC PROV LIST: ok
Starting Management Services:
Web Server: ok
CLI: ok
Secure Web: Web Authentication Certificate not found (error). If you cannot access management interface via HTTPS please reconfigure Virtual Interface.
(Cisco Controller)
Welcome to the Cisco Wizard Configuration Tool
Use the '-' character to backup
Would you like to terminate autoinstall? [yes]:
AUTO-INSTALL: starting now...
Through Session
HO2NET0001##session switch 1 slot 4 proc 1
The default escape character is Ctrl-^, then x. You can also type 'exit' at the remote prompt to end the session Trying 0.0.0.0 ...
Any assistance or ideas offered will be greatly appreciated.
Thanks,Hi Tabish,
How many times do you have to open this same topic?
In my opinion, this is your THIRD thread for the same topic.
Maybe you are looking for
-
I am on a Mac running the last version of Snow Leopard before Mavericks, 10.8.5. I am unable to install the new Flash Player 12.0.0.4--at about the 50% mark on the installing bar, it stops and I get an error message that installation failed. The ve
-
Fine positioning of objects in Keynote
Does anyone have any tips to help me create Keynotes on the iPad - specifically to do with aligning and positioning objects? Examples: I imported a Keynote from my Mac and noticed later that the new font had moved a few objects. I needed to shift a c
-
Converse 2300 - Problem with storing similar numbe...
Hi. We have several Converse 2300 phones in the office and I am trying to store two numbers we use the most under the one-touch memory buttons. The trouble that I am having is that because these two numbers coincidentally have the same last 6 digit
-
Database Migration 10g, difference in export/import from 8.1.6 and DBUA
i would like to know if there is any difference in migrating using export/import methods from 8.1.6 and migration using dbua from 8.1.6 -> 8.1.7 -> 10g. In terms of tablespaces, datafiles performance . Will the DBUA convert the tablespaces automatica
-
Not able to select a row in ALV?
Hi Experts, I am enhancing a standard e-recruiting WD ABAP component. It produces a search result as ALV. I am not able to select any row in ALV by clicking it like we normally do in ALV. I wrote below code to allow selection: lo_value->if_wd_salv_ta