IPSEC Tunnel Failover MPLS

Thank you all for your help. I've been looking through the threads and found a few good ideas however my search found things I had already gotten to work. So here is my task.
Main Office
Backup Office
Small Remote Offices (20+)
All IPSEC VPN's come into the main office. When the main office internet fails we route all of the main office traffic to our Backup office that has a large internet connection that we can see over our MPLS network.
This back up works for basic internet connections. However the "non MPLS" offices loose access to email and our corporate resources that they see via IPSec.
How do I set up the ASA(or networks) so that the Corporate network can automatically be seen via the IPSec tunnels coming out of the Backup Office.

This link shows the process of creating and applying a profile to an IPSec tunnel. The necessary preliminary steps are also shown. You must first define a transform set and then create a profile before configuring the IPSec tunnel.
http://www.cisco.com/en/US/docs/ios_xr_sw/iosxr_r3.0/interfaces/configuration/guide/hc3tunne.html#wp1356228

Similar Messages

IPSec tunnel on sub-interface on ASA 5510

Hello All,
I working on a security solution using ASA firewall and need some technical advice on ASA. Is it possible to setup a IPSec tunnels on each subinterface of a physical interface on ASA 5510?
I would be greatul if someone please reply post this with some details.
Regards,
Muds

Hi Jennifer,
Thanks very much for your reply. I understand where you coming from, but the reason of using sub-interfaces is that, we have only one physical interface on the firewall connected to the MPLS cloud, and we need to setup a seperate IPSec tunnels for each client for security and integrity. In the current scenario, I have static peers and we can easily setup a static route to peer address.
Many thanks for your assistance, please feel free to to advise if you have any other suggestion.
Regards,
Muds

The tale of two IPSec Tunnels...

I'm trying to set up an ipsec tunnel at a particular site, and I am just stumped at this point. I have two sites I'm working with, a test site on my bench and the other actual site at another location. Both are ASA 5510's, both are running ASA v8.2(5). The test site has a 3560 off of it, and the production site has a 3750 stack off it. I don't think that part should matter, though.
I used the wizard to create the ipsec configuration on both devices, test and prod, and used the same naming on both to help compare. The test site connects and I can ssh to the 3560 behind it just fine. The production site, however, cannot connect to that 3750 or ping it to save my life. I've poured through the configs on both, and although there are just a couple of differences, the two ASA's are pretty close in configs.
At first I thought it was an acl issue, but I've filtered the logs by syslog id 106023 to watch for denys by access group. When I try to connect to the 3750, I get absolutely no entry in the log that anything is being denied, so I figure that's not it.
Then I thought it may be a routing issue. The one difference between the two sites is that the test site is using eigrp to disperse routes between the asa and switch, while the production site is using static routes. But I also didn't think that would've mattered, because on the static route switch I even put a static route in there to the vpn network which didn't make a difference.
I've also run packet traces on the firewall when doing a ping, and on the test siteI see echo requests and replies. Oon the production site I only see requests, no replies. My encap counters don't increment during pings, but the decap counters do, which make sense.
Other things to note: The test site that works also has a site-to-site vpn up and runnning, so you'll see that in the config as well. Client is Mac OS X 10.6.8, using the Cisco IPSec Config.
I'm hoping someone can look at my configs and tell me if they see anything I'm missing on them that could help solve my problems. I'd appreciate it! Thanks
Test Site that works
Production Site that Doesn't
testasa01-5510# sh run
: Saved
ASA Version 8.2(5)
hostname testasa01-5510
names
interface Ethernet0/0
nameif outside
security-level 0
ip address <outsideif> 255.255.255.240
interface Ethernet0/1
nameif inside
security-level 100
ip address 10.39.194.2 255.255.255.248
interface Ethernet0/2
shutdown
no nameif
no security-level
no ip address
interface Ethernet0/3
shutdown
no nameif
no security-level
no ip address
interface Management0/0
nameif management
security-level 100
no ip address
management-only
boot system disk0:/asa825-k8.bin
ftp mode passive
clock timezone PST -8
clock summer-time PDT recurring
access-list inside_access_in extended permit ip 10.39.0.0 255.255.0.0 any log disable
access-list RemoteAccess_splitTunnelAcl standard permit 10.0.0.0 255.0.0.0
access-list inside_nat0_outbound extended permit ip 10.39.0.0 255.255.0.0 10.0.0.0 255.0.0.0
access-list inside_nat0_outbound extended permit ip 10.0.0.0 255.0.0.0 172.16.139.0 255.255.255.240
access-list outside_cryptomap extended permit ip 10.39.0.0 255.255.0.0 10.0.0.0 255.0.0.0
access-list remoteaccess extended permit ip 172.16.139.0 255.255.255.240 any log disable
tcp-map WSOptions
tcp-options range 24 31 allow
pager lines 24
logging enable
logging asdm informational
mtu outside 1500
mtu inside 1500
mtu management 1500
ip local pool vpn_ip_pool 172.16.139.0-172.16.139.10 mask 255.255.255.0
no failover
icmp unreachable rate-limit 1 burst-size 1
asdm image disk0:/asdm-713.bin
no asdm history enable
arp timeout 14400
global (outside) 100 interface
nat (inside) 0 access-list inside_nat0_outbound
nat (inside) 100 10.39.0.0 255.255.0.0
access-group inside_access_in in interface inside
router eigrp 100
network 10.0.0.0 255.0.0.0
passive-interface default
no passive-interface inside
route outside 0.0.0.0 0.0.0.0 <outsideif> 1
timeout xlate 3:00:00
timeout conn 1:00:00 half-closed 0:10:00 udp 0:02:00 icmp 0:00:02
timeout sunrpc 0:10:00 h323 0:05:00 h225 1:00:00 mgcp 0:05:00 mgcp-pat 0:05:00
timeout sip 0:30:00 sip_media 0:02:00 sip-invite 0:03:00 sip-disconnect 0:02:00
timeout sip-provisional-media 0:02:00 uauth 0:05:00 absolute
timeout tcp-proxy-reassembly 0:01:00
timeout floating-conn 0:00:00
dynamic-access-policy-record DfltAccessPolicy
aaa authentication ssh console LOCAL
http server enable
http 10.0.0.0 255.0.0.0 management
http 10.0.0.0 255.0.0.0 inside
no snmp-server location
no snmp-server contact
snmp-server enable traps snmp authentication linkup linkdown coldstart
crypto ipsec transform-set ESP-AES-128-SHA esp-aes esp-sha-hmac
crypto ipsec transform-set ESP-AES-128-MD5 esp-aes esp-md5-hmac
crypto ipsec transform-set ESP-AES-192-SHA esp-aes-192 esp-sha-hmac
crypto ipsec transform-set ESP-AES-192-MD5 esp-aes-192 esp-md5-hmac
crypto ipsec transform-set ESP-AES-256-SHA esp-aes-256 esp-sha-hmac
crypto ipsec transform-set ESP-AES-256-MD5 esp-aes-256 esp-md5-hmac
crypto ipsec transform-set ESP-AES-128-SHA-TRANS esp-aes esp-sha-hmac
crypto ipsec transform-set ESP-AES-128-SHA-TRANS mode transport
crypto ipsec transform-set ESP-AES-128-MD5-TRANS esp-aes esp-md5-hmac
crypto ipsec transform-set ESP-AES-128-MD5-TRANS mode transport
crypto ipsec transform-set ESP-AES-192-SHA-TRANS esp-aes-192 esp-sha-hmac
crypto ipsec transform-set ESP-AES-192-SHA-TRANS mode transport
crypto ipsec transform-set ESP-AES-192-MD5-TRANS esp-aes-192 esp-md5-hmac
crypto ipsec transform-set ESP-AES-192-MD5-TRANS mode transport
crypto ipsec transform-set ESP-AES-256-SHA-TRANS esp-aes-256 esp-sha-hmac
crypto ipsec transform-set ESP-AES-256-SHA-TRANS mode transport
crypto ipsec transform-set ESP-AES-256-MD5-TRANS esp-aes-256 esp-md5-hmac
crypto ipsec transform-set ESP-AES-256-MD5-TRANS mode transport
crypto ipsec transform-set ESP-3DES-MD5 esp-3des esp-md5-hmac
crypto ipsec transform-set ESP-3DES-SHA-TRANS esp-3des esp-sha-hmac
crypto ipsec transform-set ESP-3DES-SHA-TRANS mode transport
crypto ipsec transform-set ESP-3DES-MD5-TRANS esp-3des esp-md5-hmac
crypto ipsec transform-set ESP-3DES-MD5-TRANS mode transport
crypto ipsec transform-set ESP-DES-SHA esp-des esp-sha-hmac
crypto ipsec transform-set ESP-DES-MD5 esp-des esp-md5-hmac
crypto ipsec transform-set ESP-DES-SHA-TRANS esp-des esp-sha-hmac
crypto ipsec transform-set ESP-DES-SHA-TRANS mode transport
crypto ipsec transform-set ESP-DES-MD5-TRANS esp-des esp-md5-hmac
crypto ipsec transform-set ESP-DES-MD5-TRANS mode transport
crypto ipsec transform-set ESP-3DES-SHA esp-3des esp-sha-hmac
crypto ipsec security-association lifetime seconds 28800
crypto ipsec security-association lifetime kilobytes 4608000
crypto dynamic-map SYSTEM_DEFAULT_CRYPTO_MAP 65535 set pfs group1
crypto dynamic-map SYSTEM_DEFAULT_CRYPTO_MAP 65535 set transform-set ESP-AES-128-SHA ESP-AES-128-MD5 ESP-AES-192-SHA ESP-AES-192-MD5 ESP-AES-256-SHA ESP-AES-256-MD5 ESP-3DES-SHA ESP-3DES-MD5 ESP-DES-SHA ESP-DES-MD5
crypto map outside_map1 1 match address outside_cryptomap
crypto map outside_map1 1 set pfs group1
crypto map outside_map1 1 set peer 209.242.145.200
crypto map outside_map1 1 set transform-set ESP-AES-128-SHA ESP-AES-128-MD5 ESP-AES-192-SHA ESP-AES-192-MD5 ESP-AES-256-SHA ESP-AES-256-MD5 ESP-3DES-SHA ESP-3DES-MD5 ESP-DES-SHA ESP-DES-MD5
crypto map outside_map1 65535 ipsec-isakmp dynamic SYSTEM_DEFAULT_CRYPTO_MAP
crypto map outside_map1 interface outside
crypto isakmp enable outside
crypto isakmp policy 10
authentication crack
encryption aes-256
hash sha
group 2
lifetime 86400
crypto isakmp policy 20
authentication rsa-sig
encryption aes-256
hash sha
group 2
lifetime 86400
crypto isakmp policy 30
authentication pre-share
encryption aes-256
hash sha
group 2
lifetime 86400
crypto isakmp policy 40
authentication crack
encryption aes-192
hash sha
group 2
lifetime 86400
crypto isakmp policy 50
authentication rsa-sig
encryption aes-192
hash sha
group 2
lifetime 86400
crypto isakmp policy 60
authentication pre-share
encryption aes-192
hash sha
group 2
lifetime 86400
crypto isakmp policy 70
authentication crack
encryption aes
hash sha
group 2
lifetime 86400
crypto isakmp policy 80
authentication rsa-sig
encryption aes
hash sha
group 2
lifetime 86400
crypto isakmp policy 90
authentication pre-share
encryption aes
hash sha
group 2
lifetime 86400
crypto isakmp policy 100
authentication crack
encryption 3des
hash sha
group 2
lifetime 86400
crypto isakmp policy 110
authentication rsa-sig
encryption 3des
hash sha
group 2
lifetime 86400
crypto isakmp policy 120
authentication pre-share
encryption 3des
hash sha
group 2
lifetime 86400
crypto isakmp policy 130
authentication crack
encryption des
hash sha
group 2
lifetime 86400
crypto isakmp policy 140
authentication rsa-sig
encryption des
hash sha
group 2
lifetime 86400
crypto isakmp policy 150
authentication pre-share
encryption des
hash sha
group 2
lifetime 86400
crypto isakmp policy 170
authentication pre-share
encryption 3des
hash sha
group 1
lifetime 86400
telnet timeout 5
ssh 10.0.0.0 255.0.0.0 inside
ssh 0.0.0.0 0.0.0.0 management
ssh timeout 60
console timeout 0
management-access inside
threat-detection basic-threat
threat-detection statistics access-list
no threat-detection statistics tcp-intercept
ntp server <server> source inside
webvpn
group-policy GroupPolicy1 internal
group-policy GroupPolicy1 attributes
vpn-tunnel-protocol IPSec
group-policy RemoteAccess internal
group-policy RemoteAccess attributes
dns-server value 8.8.8.8
vpn-filter value remoteaccess
vpn-tunnel-protocol IPSec
split-tunnel-policy tunnelspecified
split-tunnel-network-list value RemoteAccess_splitTunnelAcl
split-tunnel-all-dns disable
vlan none
tunnel-group RemoteAccess type remote-access
tunnel-group RemoteAccess general-attributes
address-pool vpn_ip_pool
default-group-policy RemoteAccess
tunnel-group RemoteAccess ipsec-attributes
pre-shared-key *****
tunnel-group 111.222.333.444 type ipsec-l2l
tunnel-group 111.222.333.444
general-attributes
default-group-policy GroupPolicy1
tunnel-group 111.222.333.444
ipsec-attributes
pre-shared-key *****
class-map WSOptions-class
match any
class-map inspection_default
match default-inspection-traffic
policy-map type inspect dns preset_dns_map
parameters
message-length maximum 512
policy-map global_policy
class inspection_default
inspect dns preset_dns_map
inspect ftp
inspect h323 h225
inspect h323 ras
inspect rsh
inspect rtsp
inspect esmtp
inspect sqlnet
inspect skinny
inspect sunrpc
inspect xdmcp
inspect sip
inspect netbios
inspect tftp
inspect ip-options
class WSOptions-class
set connection advanced-options WSOptions
policy-map type inspect ip-options ip-options-map
parameters
eool action allow
nop action allow
router-alert action allow
service-policy global_policy global
prompt hostname context
no call-home reporting anonymous
call-home
profile CiscoTAC-1
no active
destination address http https://tools.cisco.com/its/service/oddce/services/DDCEService
destination address email [email protected]
destination transport-method http
subscribe-to-alert-group diagnostic
subscribe-to-alert-group environment
subscribe-to-alert-group inventory periodic monthly
subscribe-to-alert-group configuration periodic monthly
subscribe-to-alert-group telemetry periodic daily
: end
mp01-5510asa# sh run
: Saved
ASA Version 8.2(5)
hostname mp01-5510asa
names
interface Ethernet0/0
nameif inside
security-level 100
ip address 10.29.194.2 255.255.255.252
interface Ethernet0/1
nameif dmz
security-level 50
ip address 172.16.29.1 255.255.255.0
interface Ethernet0/2
description
nameif backup
security-level 0
ip address <backupif> 255.255.255.252
interface Ethernet0/3
description
speed 100
duplex full
nameif outside
security-level 0
ip address <outsideif> 255.255.255.248
interface Management0/0
nameif management
security-level 100
ip address 10.29.199.11 255.255.255.0
management-only
banner login Authorized Use Only
boot system disk0:/asa825-k8.bin
ftp mode passive
clock timezone PST -8
clock summer-time PDT recurring
object-group network DM_INLINE_NETWORK_1
network-object 10.29.1.0 255.255.255.0
network-object 10.29.15.0 255.255.255.0
network-object 10.29.199.0 255.255.255.0
network-object 10.29.200.0 255.255.255.0
network-object 10.29.31.0 255.255.255.0
access-list inside_access_in extended permit ip 10.29.0.0 255.255.0.0 any log warnings
access-list inside_access_in extended permit ip object-group DM_INLINE_NETWORK_1 any log warnings
access-list inside_access_in extended permit ip 192.168.29.0 255.255.255.0 any log warnings
access-list inside_access_in extended permit ip 10.29.32.0 255.255.255.0 any log warnings
access-list outside_access_in extended permit ip any host 50.59.30.116 log warnings
access-list RemoteAccess_splitTunnelAcl standard permit 10.0.0.0 255.0.0.0
access-list inside_nat0_outbound extended permit ip 10.0.0.0 255.0.0.0 10.254.29.0 255.255.255.0 log warnings
access-list remoteaccess extended permit ip 10.254.29.0 255.255.255.0 any log warnings
access-list RemoteAccess2_splitTunnelAcl standard permit 10.29.0.0 255.255.0.0
pager lines 24
logging enable
logging list acl-messages message 106023
logging buffered acl-messages
logging asdm acl-messages
mtu inside 1500
mtu dmz 1500
mtu backup 1500
mtu outside 1500
mtu management 1500
ip local pool vpn_ip_pool3 10.254.29.0-10.254.29.10 mask 255.255.255.0
no failover
icmp unreachable rate-limit 1 burst-size 1
asdm image disk0:/asdm-645.bin
asdm history enable
arp timeout 14400
global (inside) 201 interface
global (dmz) 101 interface
global (backup) 101 interface
global (outside) 101 interface
nat (inside) 0 access-list inside_nat0_outbound
nat (inside) 101 10.29.1.0 255.255.255.0
nat (inside) 101 10.29.15.0 255.255.255.0
nat (inside) 101 10.29.31.0 255.255.255.0
nat (inside) 101 10.29.32.0 255.255.255.0
nat (inside) 101 10.29.199.0 255.255.255.0
nat (inside) 101 10.29.200.0 255.255.255.0
nat (inside) 101 192.168.29.0 255.255.255.0
static (inside,outside) <outsideif> 10.29.15.10 netmask 255.255.255.255
access-group inside_access_in in interface inside
access-group outside_access_in in interface outside
route outside 0.0.0.0 0.0.0.0 50.59.30.113 1 track 1
route backup 0.0.0.0 0.0.0.0 205.179.122.165 254
route management 10.0.0.0 255.0.0.0 10.29.199.1 1
route inside 10.29.0.0 255.255.0.0 10.29.194.1 1
route inside 192.168.29.0 255.255.255.0 10.29.194.1 1
timeout xlate 3:00:00
timeout conn 1:00:00 half-closed 0:10:00 udp 0:02:00 icmp 0:00:02
timeout sunrpc 0:10:00 h323 0:05:00 h225 1:00:00 mgcp 0:05:00 mgcp-pat 0:05:00
timeout sip 0:30:00 sip_media 0:02:00 sip-invite 0:03:00 sip-disconnect 0:02:00
timeout sip-provisional-media 0:02:00 uauth 0:05:00 absolute
timeout tcp-proxy-reassembly 0:01:00
timeout floating-conn 0:00:00
dynamic-access-policy-record DfltAccessPolicy
aaa authentication ssh console LOCAL
aaa authentication enable console LOCAL
http server enable
http 10.0.0.0 255.0.0.0 management
http 10.0.0.0 255.0.0.0 inside
no snmp-server location
no snmp-server contact
snmp-server enable traps snmp authentication linkup linkdown coldstart
sla monitor 100
type echo protocol ipIcmpEcho 74.125.239.16 interface outside
num-packets 3
frequency 10
sla monitor schedule 100 life forever start-time now
crypto ipsec transform-set ESP-AES-256-MD5 esp-aes-256 esp-md5-hmac
crypto ipsec transform-set ESP-DES-SHA esp-des esp-sha-hmac
crypto ipsec transform-set ESP-DES-MD5 esp-des esp-md5-hmac
crypto ipsec transform-set ESP-AES-192-MD5 esp-aes-192 esp-md5-hmac
crypto ipsec transform-set ESP-3DES-MD5 esp-3des esp-md5-hmac
crypto ipsec transform-set ESP-AES-256-SHA esp-aes-256 esp-sha-hmac
crypto ipsec transform-set ESP-AES-128-SHA esp-aes esp-sha-hmac
crypto ipsec transform-set ESP-AES-192-SHA esp-aes-192 esp-sha-hmac
crypto ipsec transform-set ESP-AES-128-MD5 esp-aes esp-md5-hmac
crypto ipsec transform-set ESP-3DES-SHA esp-3des esp-sha-hmac
crypto ipsec security-association lifetime seconds 28800
crypto ipsec security-association lifetime kilobytes 4608000
crypto dynamic-map SYSTEM_DEFAULT_CRYPTO_MAP 65535 set pfs group1
crypto dynamic-map SYSTEM_DEFAULT_CRYPTO_MAP 65535 set transform-set ESP-AES-128-SHA ESP-AES-128-MD5 ESP-AES-192-SHA ESP-AES-192-MD5 ESP-AES-256-SHA ESP-AES-256-MD5 ESP-3DES-SHA ESP-3DES-MD5 ESP-DES-SHA ESP-DES-MD5
crypto map outside_map 65535 ipsec-isakmp dynamic SYSTEM_DEFAULT_CRYPTO_MAP
crypto map outside_map interface outside
crypto isakmp enable outside
crypto isakmp policy 10
authentication pre-share
encryption 3des
hash md5
group 2
lifetime 86400
crypto isakmp policy 30
authentication pre-share
encryption 3des
hash sha
group 2
lifetime 86400
track 1 rtr 100 reachability
telnet timeout 5
ssh 10.0.0.0 255.0.0.0 inside
ssh 10.0.0.0 255.0.0.0 management
ssh timeout 60
console timeout 0
threat-detection basic-threat
threat-detection statistics access-list
no threat-detection statistics tcp-intercept
ntp server 10.200.1.41 source inside
webvpn
group-policy RemoteAccess internal
group-policy RemoteAccess attributes
dns-server value 8.8.8.8
vpn-filter value remoteaccess
vpn-tunnel-protocol IPSec
split-tunnel-policy tunnelspecified
split-tunnel-network-list value RemoteAccess_splitTunnelAcl
split-tunnel-all-dns disable
vlan none
tunnel-group RemoteAccess type remote-access
tunnel-group RemoteAccess general-attributes
address-pool vpn_ip_pool3
default-group-policy RemoteAccess
tunnel-group RemoteAccess ipsec-attributes
pre-shared-key *****
class-map inspection_default
match default-inspection-traffic
policy-map type inspect dns preset_dns_map
parameters
message-length maximum 512
policy-map global_policy
class inspection_default
inspect ftp
inspect h323 h225
inspect h323 ras
inspect rsh
inspect rtsp
inspect esmtp
inspect sqlnet
inspect skinny
inspect sunrpc
inspect xdmcp
inspect sip
inspect netbios
inspect tftp
inspect icmp
prompt hostname context
no call-home reporting anonymous
call-home
profile CiscoTAC-1
no active
destination address http https://tools.cisco.com/its/service/oddce/services/DDCEService
destination address email [email protected]
destination transport-method http
subscribe-to-alert-group diagnostic
subscribe-to-alert-group environment
subscribe-to-alert-group inventory periodic monthly
subscribe-to-alert-group configuration periodic monthly
subscribe-to-alert-group telemetry periodic daily
testasa01-5510# sh crypto ipsec sa
interface: outside
    Crypto map tag: SYSTEM_DEFAULT_CRYPTO_MAP, seq num: 65535, local addr: <outsideif>
      local ident (addr/mask/prot/port): (10.0.0.0/255.0.0.0/0/0)
      remote ident (addr/mask/prot/port): (172.16.139.1/255.255.255.255/0/0)
      current_peer: <peer ip>, username: blah
      dynamic allocated peer ip: 172.16.139.1
      #pkts encaps: 0, #pkts encrypt: 0, #pkts digest: 0
      #pkts decaps: 30, #pkts decrypt: 30, #pkts verify: 30
      #pkts compressed: 0, #pkts decompressed: 0
      #pkts not compressed: 0, #pkts comp failed: 0, #pkts decomp failed: 0
      #pre-frag successes: 0, #pre-frag failures: 0, #fragments created: 0
      #PMTUs sent: 0, #PMTUs rcvd: 0, #decapsulated frgs needing reassembly: 0
      #send errors: 0, #recv errors: 0
      local crypto endpt.: <outsideif>/4500, remote crypto endpt.: <peer ip>/37291
      path mtu 1500, ipsec overhead 82, media mtu 1500
      current outbound spi: 0A7F396F
      current inbound spi : E87AF806
    inbound esp sas:
      spi: 0xE87AF806 (3900372998)
         transform: esp-aes esp-sha-hmac no compression
         in use settings ={RA, Tunnel, NAT-T-Encaps, }
         slot: 0, conn_id: 49152, crypto-map: SYSTEM_DEFAULT_CRYPTO_MAP
         sa timing: remaining key lifetime (sec): 3587
         IV size: 16 bytes
         replay detection support: Y
         Anti replay bitmap:
          0x00000000 0x7FFFFFFF
    outbound esp sas:
      spi: 0x0A7F396F (176109935)
         transform: esp-aes esp-sha-hmac no compression
         in use settings ={RA, Tunnel, NAT-T-Encaps, }
         slot: 0, conn_id: 49152, crypto-map: SYSTEM_DEFAULT_CRYPTO_MAP
         sa timing: remaining key lifetime (sec): 3587
         IV size: 16 bytes
         replay detection support: Y
         Anti replay bitmap:
          0x00000000 0x00000001
mp01-5510asa# sh crypto ipsec sa
interface: outside
    Crypto map tag: SYSTEM_DEFAULT_CRYPTO_MAP, seq num: 65535, local addr: <outsideif>
      local ident (addr/mask/prot/port): (10.0.0.0/255.0.0.0/0/0)
      remote ident (addr/mask/prot/port): (10.254.29.1/255.255.255.255/0/0)
      current_peer: <peer ip>, username: blah
      dynamic allocated peer ip: 10.254.29.1
      #pkts encaps: 0, #pkts encrypt: 0, #pkts digest: 0
      #pkts decaps: 51, #pkts decrypt: 51, #pkts verify: 51
      #pkts compressed: 0, #pkts decompressed: 0
      #pkts not compressed: 0, #pkts comp failed: 0, #pkts decomp failed: 0
      #pre-frag successes: 0, #pre-frag failures: 0, #fragments created: 0
      #PMTUs sent: 0, #PMTUs rcvd: 0, #decapsulated frgs needing reassembly: 0
      #send errors: 0, #recv errors: 0
      local crypto endpt.: <outsideif>/4500, remote crypto endpt.: <peer ip>/37291
      path mtu 1500, ipsec overhead 82, media mtu 1500
      current outbound spi: 096265D4
      current inbound spi : F5E4780C
    inbound esp sas:
      spi: 0xF5E4780C (4125390860)
         transform: esp-aes esp-sha-hmac no compression
         in use settings ={RA, Tunnel, NAT-T-Encaps, }
         slot: 0, conn_id: 102400, crypto-map: SYSTEM_DEFAULT_CRYPTO_MAP
         sa timing: remaining key lifetime (sec): 3576
         IV size: 16 bytes
         replay detection support: Y
         Anti replay bitmap:
          0x001FFFFF 0xFFFFFFFF
    outbound esp sas:
      spi: 0x096265D4 (157443540)
         transform: esp-aes esp-sha-hmac no compression
         in use settings ={RA, Tunnel, NAT-T-Encaps, }
         slot: 0, conn_id: 102400, crypto-map: SYSTEM_DEFAULT_CRYPTO_MAP
         sa timing: remaining key lifetime (sec): 3576
         IV size: 16 bytes
         replay detection support: Y
         Anti replay bitmap:
          0x00000000 0x00000001

Config (non working site) looks fine(unless I missed something:)) . You may want to add :
access-list RemoteAccess_splitTunnelAcl standard permit 192.168.29.0 255.255.255.0
Try by taking out vpnfilter : vpn-filter value remoteaccess
To further t-shoot, try using packet tracer from ASA to the client...
https://supportforums.cisco.com/docs/DOC-5796
Thx
MS

Ipsec tunnel possible with Checkpoint ngx 6.5 and Cisco ISR-dual ISP?

Hi Gurus,
I have a requirement to fulfill in that there are 2 sites that I need to create an ipsec tunnel. A remote site running a Checkpoint ngx 6.5 and a local site with 2 different ISPs and 2 x ISR 29xx routers for both ISP and hardware redundancy. I have only done the vpn setup with one ISR and ISP1 so far.
I am planning to have just 1 ISR (ISR1) and ISP1 being active at any given time. If ISP1 or ISR 1 goes out, all traffic should fail over to ISR2 with ISP2.
is this possible with the ISRs?
Checkpoint does not appear to allow seeing the different ISRs with 2 possible WAN ip addresses with the same encryption domain or 'interesting traffic', so i am not sure if this work at all.
BGP won't be used.
I have looked at ip sla, pbr, and it appears that the best I could achieve would be vpn traffic via ISR1 and ISP1, and could failover only the non vpn traffic to ISR2 and ISP2. Please correct me if I am wrong....many thanks.
Any ideas will be greatly appreciated..
Civicfan

I found the problem but dont know how to fix it now!
Problem is on siteB with using the same ACL name "siteA" in both sequence numbers in cryptomap "outside_map"
crypto map outside_map 9 match address SiteA
crypto map outside_map 9 set peer 212.89.229.xx
crypto map outside_map 9 set transform-set ESP-AES-256-SHA
crypto map outside_map 9 set security-association lifetime seconds 28800
crypto map outside_map 9 set security-association lifetime kilobytes 4608000
crypto map outside_map 10 match address SiteA
crypto map outside_map 10 set peer 212.89.235.yy
crypto map outside_map 10 set transform-set ESP-AES-256-SHA
crypto map outside_map 10 set security-association lifetime seconds 28800
crypto map outside_map 10 set security-association lifetime kilobytes 4608000
If I remove:
no crypto map outside_map 9 match address SiteA
the IPSEC through 2nd ISP on siteA is working correct

IPSEC Tunnel Redundancy

I've got two ASA5510's, I have SITE-A and SITE-B
SITE-A connects to the INTERNET on one circuit and an MPLS circuit on different interfaces on the router.
SITE-B connects to the INTERNET and MPLS on the same circuit.
My outside interface on the ASA at SITE-A has a public address of: 1.2.3.4. On the router, it NAT's that address to 10.25.25.5/29 when going out the MPLS interface.
At SITE-B, the outside interface on the ASA is 10.25.25.13/30 which has public ip address 4.3.2.1 nat'ed to it.
Currently, I am able to create two distinct (one at a time) tunnels which route the appropriate traffic through them. One tunnel is done completely over the MPLS circuit from site to site. The other tunnel goes out of SITE-A's internet connection, and jumps on the MPLS providers public network, then onto the MPLS network to get to SITE-B.
These both work marvelously. I am trying to accomplish haveing the IPSEC tunnel go over the MPLS circuit by default, but in the event that SITE-A loses MPLS connectivity, the tunnel will go over the internet.
These tunnels are currently landing on the ASA's and are not originating or landing on the routers, so I can't use (that I know of) routing on the router to determine which site to connect to.
TUNNEL-A = 10.25.25.5 to 10.25.25.13
TUNNEL-B = 1.2.3.4 to 4.3.2.1
Any information, or advice about this configuration would be greatly appreciated.
Thank you.

I don't know if this will solve your issue, but have you tried static route tracking?
http://www.cisco.com/en/US/products/hw/vpndevc/ps2030/products_configuration_example09186a00806e880b.shtml

IPSec Tunnel and Making Changes While Up

My main MPLS circuit is down and i have two IPSec tunnels up to my remote sites.
Everything is routing fine but i wanted to add a sub net to my NAT and Tunnels.
Can i add a new subnet to my local network/remote network and save/apply without killing or reseting my active IPSec tunnels?

Reza has interpreted your question in terms of NAT and I agree with him that you should be able to change the NAT configuration without impacting other parts of the router operation and connectivity.
But I read your question as involving both NAT and IPSec tunnels. And I believe that the answer is different when you consider IPSec tunnels. You can go ahead and change the configuration of the tunnels while they are up. But the tunnels negotiated their Security Associations based on the config in place when the tunnels came up. They will continue to use those Security Associations after you make your config change. So if you are changing things like what subnets are in the access list used to identify traffic for IPSec these changes will not take effect until a new Security Association is negotiated. You can either wait for the lifetime to expire and new SA negotiated or your can reset the IPSec tunnels and force a new negotiation. Also note that if you are changing the access list on your end that someone on the other end needs to make a corresponding change on their end.
HTH
Rick

Cisco ASA 5505 Site to site VPN IPSEC tunnel to an Clavister Firewall

Hi,
I have weird problem with a Site to site VPN tunnel from a Cisco ASA 5505 to an Clavister Firewall.
When I restart the Cisco ASA 5505 the tunnel is up and down,up, down, down, and I get all strange messages when I see if the tunnel is up or down with the syntax: show crypto isakmp sa
After a while like 5-10 min the vpn site to site tunnel is up and here is the strange thing happening I have all accesslists and tunnel accesslists right I can only access one remote network (Main site Clavister Firewall) trought the vpn tunnel behind the Cisco ASA 5505, and I have 5 more remote networks that I want to access but only one remote network is working trought the vpn tunnel behind the Cisco ASA. I see that when I do this syntax in ASA: show crypto ipsec sa.
They had a Clavister Firewall before on that site before and now they have a Cisco ASA 5505 and all the rules on the main site thats have the big Clavister Firewall is intact so the problems are in the Cisco ASA 5505.
Here is some logs that ASDM give me about the tunnel issue, but like I said, the tunnel is up and only one remote network is reachable in that tunnel.....
3
Nov 21 2012
07:11:09
713902
Group = 195.149.180.254, IP = 195.149.169.254, Removing peer from correlator table failed, no match!
3
Nov 21 2012
07:11:09
713902
Group = 195.149.180.254, IP = 195.149.169.254, QM FSM error (P2 struct &0xc92462d0, mess id 0x1c6bf927)!
3
Nov 21 2012
07:11:09
713061
Group = 195.149.180.254, IP = 195.149.169.254, Rejecting IPSec tunnel: no matching crypto map entry for remote proxy 0.0.0.0/0.0.0.0/0/0 local proxy 0.0.0.0/0.0.0.0/0/0 on interface outside
5
Nov 21 2012
07:11:09
713119
Group = 195.149.180.254, IP = 195.149.169.254, PHASE 1 COMPLETED
Here is from the syntax: show crypto isakmp sa
Result of the command: "show crypto isakmp sa"
   Active SA: 1
    Rekey SA: 0 (A tunnel will report 1 Active and 1 Rekey SA during rekey)
Total IKE SA: 1
1   IKE Peer: 195.149.180.254
    Type    : L2L             Role    : responder
    Rekey   : no              State   : MM_ACTIVE
Result of the command: "show crypto ipsec sa"
interface: outside
    Crypto map tag: CustomerCryptoMap, seq num: 10, local addr: 213.180.90.29
      access-list arvika_garnisonen permit ip 172.22.65.0 255.255.255.0 192.168.123.0 255.255.255.0
      local ident (addr/mask/prot/port): (172.22.65.0/255.255.255.0/0/0)
      remote ident (addr/mask/prot/port): (192.168.123.0/255.255.255.0/0/0)
      current_peer:195.149.180.254
      #pkts encaps: 2188, #pkts encrypt: 2188, #pkts digest: 2188
      #pkts decaps: 2082, #pkts decrypt: 2082, #pkts verify: 2082
      #pkts compressed: 0, #pkts decompressed: 0
      #pkts not compressed: 2188, #pkts comp failed: 0, #pkts decomp failed: 0
      #pre-frag successes: 0, #pre-frag failures: 0, #fragments created: 0
      #PMTUs sent: 0, #PMTUs rcvd: 0, #decapsulated frgs needing reassembly: 0
      #send errors: 0, #recv errors: 0
      local crypto endpt.: 213.180.67.29, remote crypto endpt.: 195.149.180.254
      path mtu 1500, ipsec overhead 74, media mtu 1500
      current outbound spi: E715B315
    inbound esp sas:
      spi: 0xFAC769EB (4207372779)
         transform: esp-aes-256 esp-sha-hmac no compression
         in use settings ={L2L, Tunnel, PFS Group 5, }
         slot: 0, conn_id: 2879488, crypto-map: CustomerCryptoMap
         sa timing: remaining key lifetime (kB/sec): (38738/2061)
         IV size: 16 bytes
         replay detection support: Y
         Anti replay bitmap:
          0xFFFFFFFF 0xFFFFFFFF
    outbound esp sas:
      spi: 0xE715B315 (3876958997)
         transform: esp-aes-256 esp-sha-hmac no compression
         in use settings ={L2L, Tunnel, PFS Group 5, }
         slot: 0, conn_id: 2879488, crypto-map: CustomerCryptoMap
         sa timing: remaining key lifetime (kB/sec): (38673/2061)
         IV size: 16 bytes
         replay detection support: Y
         Anti replay bitmap:
          0x00000000 0x00000001
And here are my Accesslists and vpn site to site config:
crypto isakmp enable outside
crypto isakmp policy 10
authentication pre-share
encryption aes-256
hash sha
group 5
lifetime 84600
crypto isakmp nat-traversal 40
crypto ipsec transform-set ESP-AES-256-SHA esp-aes-256 esp-sha-hmac
crypto ipsec security-association lifetime seconds 28800
crypto ipsec security-association lifetime kilobytes 4608000
crypto map CustomerCryptoMap 10 match address VPN_Tunnel
crypto map CustomerCryptoMap 10 set pfs group5
crypto map CustomerCryptoMap 10 set peer 195.149.180.254
crypto map CustomerCryptoMap 10 set transform-set ESP-AES-256-SHA
crypto map CustomerCryptoMap interface outside
access-list VPN_Tunnel extended permit ip 172.22.65.0 255.255.255.0 192.168.123.0 255.255.255.0 -------> This is the only remote network I can reach behind the Cisco ASA and the other remote networks dont work..
access-list VPN_Tunnel extended permit ip 172.22.65.0 255.255.255.0 host 10.1.34.5
access-list VPN_Tunnel extended permit ip 172.22.65.0 255.255.255.0 host 10.1.20.76
access-list VPN_Tunnel extended permit ip 172.22.65.0 255.255.255.0 host 62.88.129.221
access-list VPN_Tunnel extended permit ip 172.22.65.0 255.255.255.0 172.22.71.0 255.255.255.0
access-list nonat extended permit ip 172.22.65.0 255.255.255.0 192.168.123.0 255.255.255.0
access-list nonat extended permit ip 172.22.65.0 255.255.255.0 host 10.1.34.5
access-list nonat extended permit ip 172.22.65.0 255.255.255.0 host 10.1.20.76
access-list nonat extended permit ip 172.22.65.0 255.255.255.0 host 62.88.129.221
access-list nonat extended permit ip 172.22.65.0 255.255.255.0 172.22.71.0 255.255.255.0
nat (inside) 0 access-list nonat
All these remote networks are at the Main Site Clavister Firewall.
Best Regards
Michael

Hi,
I'd start by getting the configuration of the remote site related to Local/Remote network configurations and go through them. Even though no changes have been made.
If they are mirror images of eachother already I'd say its probably some problem related to Cisco/Clavister setup
Seems especially wierd to me that one of the error messages includes 0.0.0.0 lines.
I have run into some problems with L2L VPN configurations when our Cisco device just doesnt want to work with the remote end device. In some cases we have confirmed that our networks defined for the L2L VPN are exactly the same and yet when checking debugs on the ASA side we can see the remote end device using totally wrong network masks for the VPN negotiaton and therefore it failed. That problem we corrected with changing the network masks a bit.
Maybe you could try to change the Encryption Domain configurations a bit and test it then.
You could also maybe take some debugs on the Phase2 and see if you get anymore hints as to what could be the problem when only one network is working for the L2L VPN.
- Jouni

Multiple site to site IPSec tunnels to one ASA5510

Question on ASA VPN tunnels. I have one ASA 5510 in our corporate office, I have two subnets in our corporate office that are configured in the ASA in a Object group. I have a site to site IPSEC tunnel already up and that has been working. I am trying to set up another site to site IPSEC tunnel to a different location that will need to be setup to access the same two subnets. I'm not sure if this can be setup or not, I think I had a problem with setting up two tunnels that were trying to connect to the same subnet but that was between the same two ASA's. Anyways the new tunnel to a new site is not coming up and I want to make sure it is not the subnet issue. The current working tunnel is between two ASA 5510's, the new tunnel we are trying to build is between the ASA and a Sonicwall firewall. Any help would be appreciated.

Hi,
Regarding setting up the new L2L VPN connection..
Should be no problem (to my understanding) to configure the new L2L VPN connection through the other ISP interface (0/3). You will need to atleast route the remote VPN peers IP address towards that link. The L2L VPN forming should add a route for the remote networks through that L2L VPN. If not reverse route injection should handle it in the cryptomap configurations.
I guess rest of the setup depends on what will be using the 0/0 ISP and what will be using the 0/3 ISP.
If you are going to put the default route towards the 0/3 ISP you will have to think of something for the 0/0 ISP if some of your local LAN devices are going to use it for Internet also. (Possible routing problems) On the other hand if you have remote VPN Client users using the 0/0 ISP there should be no routing problem for them as they would be initiating connection through that 0/0 ISP link through ASA so ASA should know where to forward the return traffic.
Most of my 2 ISP setups have been implemented with a router in front of the actual ASA/PIX/FWSM firewalls where the router has performed Policy Routing based on the source IP address from the firewalls and then settings the correct gateway towards the correct ISP.
- Jouni

Cisco ASA 5505 IPSec tunnel won't establish until remote site attempts to connect

I have a site to site IPSec tunnel setup and operational but periodically the remote site goes down, because of a somewhat reliable internet connection. The only way to get the tunnel to re-establish is to go to the remote site and simply issue a ping from a workstation on the remote network. We were having this same issue with a Cisco PIX 506E but decided to upgrade the hardware and see if that resolve the issue. It ran for well over a year and our assumtions was that the issue was resolved. I was looking in the direction of the security-association lifetime but if we power cycle the unit, I would expect that it would kill the SA but even after power cycling, the VPN does not come up automatically.
Any assistance would be appreciated.
ASA Version 8.2(1)
hostname KRPS-FW
domain-name lottonline.org
enable password uniQue
passwd uniQue
names
interface Vlan1
nameif inside
security-level 100
ip address 10.20.30.1 255.255.255.0
interface Vlan2
nameif outside
security-level 0
ip address xxx.xxx.xxx.xxx 255.255.255.248
interface Ethernet0/0
switchport access vlan 2
interface Ethernet0/1
description Inside Network on VLAN1
interface Ethernet0/2
shutdown
interface Ethernet0/3
shutdown
interface Ethernet0/4
shutdown
interface Ethernet0/5
shutdown
interface Ethernet0/6
shutdown
interface Ethernet0/7
description Inside Network on VLAN1
ftp mode passive
dns server-group DefaultDNS
domain-name lottonline.org
access-list NONAT extended permit ip 10.20.30.0 255.255.255.0 10.20.20.0 255.255.255.0
access-list NONAT extended permit ip 10.20.30.0 255.255.255.0 192.168.0.0 255.255.255.0
access-list NONAT extended permit ip 10.20.30.0 255.255.255.0 192.168.15.0 255.255.255.0
access-list KWPS-BITP extended permit ip 10.20.30.0 255.255.255.0 10.20.20.0 255.255.255.0
access-list KWPS-BITP extended permit ip 10.20.30.0 255.255.255.0 192.168.0.0 255.255.255.0
access-list KWPS-BITP extended permit ip 10.20.30.0 255.255.255.0 192.168.15.0 255.255.255.0
icmp unreachable rate-limit 1 burst-size 1
no asdm history enable
arp timeout 14400
global (outside) 1 interface
nat (inside) 0 access-list NONAT
nat (inside) 1 0.0.0.0 0.0.0.0
access-group OUTSIDE_ACCESS_IN in interface outside
route outside 0.0.0.0 0.0.0.0 xxx.xxx.xxx.xxx 1
timeout xlate 3:00:00
timeout conn 1:00:00 half-closed 0:10:00 udp 0:02:00 icmp 0:00:02
timeout sunrpc 0:10:00 h323 0:05:00 h225 1:00:00 mgcp 0:05:00 mgcp-pat 0:05:00
timeout sip 0:30:00 sip_media 0:02:00 sip-invite 0:03:00 sip-disconnect 0:02:00
timeout sip-provisional-media 0:02:00 uauth 0:05:00 absolute
timeout tcp-proxy-reassembly 0:01:00
dynamic-access-policy-record DfltAccessPolicy
http server enable
http 10.20.30.0 255.255.255.0 inside
http 10.20.20.0 255.255.255.0 inside
snmp-server enable traps snmp authentication linkup linkdown coldstart
crypto ipsec transform-set ESP-AES-256-SHA esp-aes-256 esp-sha-hmac
crypto ipsec security-association lifetime seconds 28800
crypto ipsec security-association lifetime kilobytes 4608000
crypto dynamic-map DYNMAP 65535 set transform-set ESP-AES-256-SHA
crypto map VPNMAP 1 match address KWPS-BITP
crypto map VPNMAP 1 set peer xxx.xxx.xxx.001
crypto map VPNMAP 1 set transform-set ESP-AES-256-SHA
crypto map VPNMAP 65535 ipsec-isakmp dynamic DYNMAP
crypto map VPNMAP interface outside
crypto isakmp enable outside
crypto isakmp policy 5
authentication pre-share
encryption 3des
hash sha
group 2
lifetime 86400
crypto isakmp policy 65535
authentication pre-share
encryption 3des
hash sha
group 2
lifetime 86400
ssh timeout 5
console timeout 0
management-access inside
tunnel-group xxx.xxx.xxx.001 type ipsec-l2l
tunnel-group xxx.xxx.xxx.001 ipsec-attributes
pre-shared-key somekey

Hi there,
I had same issue with PIX 506E and it was not even a circuit issue and I got ride of it and problem got fixed with PIX515E
I don't know, the device is too old to stay alive.
thanks

All the traffic go through IPsec tunnel(site to site ) ,but something seems not working correctly

Hi, all,
I have seen a good post in google.com about how to make all the client's traffic though IPsec tunnel then out to the Internet from the Main site,now I attach this configuration and application for discussion, and what the problem is that I am still confused with the configuration on Main site , I hope anyone who can tell me more detail and how to accomplish it. Any answer will be appreciated , thank you !
Quote :
Question ? :
Mine is a very simple configuration. I have 2 sites linked via an IPsec tunnel. Dallas is my Main HQ R1 and Austin R2 is my remote office. I want all traffic from Austin to route thru the tunnel up to Dallas, then out to the Internet.
Dallas (Main) Lan Net is: 10.10.200.0/24
Austin (Remote) LAN Net is: 10.20.2.0/24
The Dallas (Main) site has a VPN config of:
Local Net: 0.0.0.0/0
Remote Net: 10.20.2.0/24
The Austin (Remote) site has a VPN config of:
10.20.2.0/24
Remote Net: 0.0.0.0/0
The tunnel gets established just fine. From the Austin LAN clients, I can ping the router at the main site (10.10.200.1). This is how I know the tunnel is created, but I cannot ping anything beyond the router from the Austin LAN, e.g. 8.8.8.8.
I'm sure it's something simple I failed to configure. Anyone have any pointers or hints?
Answer:
Thanks to Jimp from the other thread, I was able to see why it was not working. To fix, I had to change the Outbound NAT on the main side to Manual. Then I created a new Outbound NAT rule that included the subnet from the Austin network (10.20.2.0). Basically, I just created a copy of the default rule and changed the Source network.
Once I made this change, Voila! Traffic from the remote side started heading out to the Internet. Now all traffic flows thru the Main site. It makes perfect sense why I needed to make this change, it just took a slap in the head from Jimp to point me in the right direction.
My question ?
The answer said "To fix, I had to change the Outbound NAT on the main side to Manual. Then I created a new Outbound NAT rule that included the subnet from the Austin network (10.20.2.0). Basically, I just created a copy of the default rule and changed the Source network." what this mean and
how to do it , could anybody give me the specific configuration ? thanks a lot.

Thank you for Jouni's reply, following is the configuration on Cisco 2800 router ,no firewall enable, :
crypto isakmp policy 100
encr aes 256
authentication pre-share
group 2
crypto isakmp key x.x.x address 0.0.0.0 0.0.0.0
crypto isakmp keepalive 60
crypto ipsec transform-set IPsectrans esp-3des esp-md5-hmac
crypto dynamic-map IPsecdyn 100
set transform-set IPsectrans
match address 102
crypto map IPsecmap 100 ipsec-isakmp dynamic IPsecdyn
interface Loopback1
ip address 10.10.200.1 255.255.255.0
interface FastEthernet0/0
ip address 113.113.1.1 255.255.255.128
ip nat outside
ip virtual-reassembly
duplex auto
speed auto
crypto map IPsecmap
interface FastEthernet0/1
ip address 192.168.1.1 255.255.255.0
ip nat inside
ip virtual-reassembly
duplex auto
speed auto
ip route 0.0.0.0 0.0.0.0 113.113.1.2
ip http server
no ip http secure-server
ip nat inside source list 100 interface FastEthernet0/0 overload
access-list 100 permit ip 192.168.1.0 0.0.0.255 any
access-list 102 permit ip any 10.20.2.0 0.0.0.255

Static NAT with IPSec tunnel

Hi,
I have a hopefully fairly basic question regarding configuring some static NAT entries on a remote site 887 router which also has a IPSec tunnel configured back to our main office. I am fairly new to networking so forgive me if I ask some really silly questions!
I have been asked to configure some mobile phone "boost" boxes, which will take a mobile phone and send the traffic over the Internet - this is required because of the poor signal at the branch. These boxes connect via Ethernet to the local network and need a direct connection to the Internet and also certain UDP and TCP ports opening up.
There is only one local subnet on site and the ACL for the crypto map dictates that all traffic from this network to our head office go over the tunnel. What I wanted to do was create another vlan, give this a different subnet. Assign these mobile boost boxes DHCP reservations (there is no interface to them so they cannot be configured) and then allow them to break out to the Internet locally rather than send the traffic back to our head office and have to open up ports on our main ASA firewall.
From my research I came across this article (http://www.cisco.com/en/US/tech/tk583/tk372/technologies_configuration_example09186a0080094634.shtml
So I went ahead and created a separate vlan and DHCP reservation and then also followed the guidelines outlined above about using a route-map to stop the traffic being sent down the tunnel and then configured static NAT statements for each of the four ports these boost boxes need to work. I configure the ip nat inside/outside on the relevant ports (vlan 3 for inside, dialer 1 for outside)
The configuration can be seen below for the NAT part;
! Denies vpn interesting traffic but permits all other
ip access-list extended NAT-Traffic
deny ip 172.19.191.0 0.0.0.255 172.16.0.0 0.3.255.255
deny ip 172.19.191.0 0.0.0.255 10.0.0.0 0.255.255.255
deny ip 172.19.191.0 0.0.0.255 192.168.128.0 0.0.3.255
deny ip 172.19.191.0 0.0.0.255 12.15.28.0 0.0.0.255
deny ip 172.19.191.0 0.0.0.255 137.230.0.0 0.0.255.255
deny ip 172.19.191.0 0.0.0.255 165.26.0.0 0.0.255.255
deny ip 172.19.191.0 0.0.0.255 192.56.231.0 0.0.0.255
deny ip 172.19.191.0 0.0.0.255 192.168.49.0 0.0.0.255
deny ip 172.19.191.0 0.0.0.255 192.168.61.0 0.0.0.255
deny ip 172.19.191.0 0.0.0.255 192.168.240.0 0.0.7.255
deny ip 172.19.191.0 0.0.0.255 205.206.192.0 0.0.3.255
permit ip any any
! create route map
route-map POLICY-NAT 10
match ip address NAT-Traffic
! static nat
ip nat inside source static tcp 192.168.1.2 50 85.233.188.47 50 route-map POLICY-NAT extendable
ip nat inside source static udp 192.168.1.2 123 85.233.188.47 123 route-map POLICY-NAT extendable
ip nat inside source static udp 192.168.1.2 500 85.233.188.47 500 route-map POLICY-NAT extendable
ip nat inside source static udp 192.168.1.2 4500 85.233.188.47 4500 route-map POLICY-NAT extendable
Unfortunately this didn't work as expected, and soon after I configured this the VPN tunnel went down. Am I right in thinking that UDP port 500 is also the same port used by ISAKMP so by doing this configuration it effectively breaks IPSec?
Am I along the right lines in terms of configuration? And if not can anyone point me in the direction of anything that may help at all please?
Many thanks in advance
Brian

Hi,
Sorry to bump this thread up but is anyone able to assist in configuration? I am now thinking that if I have another public IP address on the router which is not used for the VPN tunnel I can perform the static NAT using that IP which should not break anything?
Thanks
Brian

Multiple IPSEC tunnels on ASA 5505

Configuring Multiple IPSEC tunnels on ASA 5505
Hi,
I need to configure 2 diffrent type of IPSEC tunnels on my ASA 5505. 1st one is static ipsec tunnel already configured between HO to site A and 2nd one is dynamic to be configure between HO to site B since site B does not have static IP so I have to configure dynamic ipsec vpn.
I have following clarification
1. After configuring dynamic ipsec Is my existing static ipsec tunnel will work simultenously?
2. can I apply different crypmap on the same outside interface? if not then what setting i need to do to make this work?
3. Do i need to create 1 more Nat0 or can i add in existing ACL which i have already created for previous.
kindly help me on this
Thanks in advance
Subhan Shaikh
France Telecom

Configuring Multiple IPSEC tunnels on ASA 5505
Hi,
I need to configure 2 diffrent type of IPSEC tunnels on my ASA 5505. 1st one is static ipsec tunnel already configured between HO to site A and 2nd one is dynamic to be configure between HO to site B since site B does not have static IP so I have to configure dynamic ipsec vpn.
I have following clarification
1. After configuring dynamic ipsec Is my existing static ipsec tunnel will work simultenously?
2. can I apply different crypmap on the same outside interface? if not then what setting i need to do to make this work?
3. Do i need to create 1 more Nat0 or can i add in existing ACL which i have already created for previous.
kindly help me on this
Thanks in advance
Subhan Shaikh
France Telecom

IPsec tunnel to a windows 2008 R2 server

I have an application that uses FTP to a win2k8r2 server. I'd like to setup an IPSEC tunnel to the windows server to encapsulate this traffic.
I've configured IPSEC in Solaris before, but not in LINUX. The implementation eludes me. I've searched online and not found anything that appears to work.
anyone got any ideas or secret documents that lines out how to do this?

yes, but not very helpful educationally. What I am trying to do is establish a permanent tunnel to a win2k8r2 server. I've got it to the point where it will establish a tunnel if the windows box initiates the transaction but my attempts fail. addtionally, the connection is not permanent. it drops every so often.
I keep getting the following errors over and over again until the windows box tries to send something.
Apr 16 13:47:01 LINUXHOST pluto[12025]: "WINHOST_Conn" #29: initiating Quick Mode PSK+ENCRYPT+TUNNEL+DONTREKEY+UP+IKEv2ALLOW+SAREFTRACK to replace #27 {using isakmp#14 msgid:41efece2 proposal=defaults pfsgroup=no-pfs}
Apr 16 13:47:01 LINUXHOST pluto[12025]: "WINHOST_Conn" #14: ignoring informational payload, type INVALID_ID_INFORMATION msgid=00000000
Apr 16 13:47:01 LINUXHOST pluto[12025]: "WINHOST_Conn" #14: received and ignored informational message
Apr 16 13:47:11 LINUXHOST pluto[12025]: "WINHOST_Conn" #14: ignoring informational payload, type INVALID_ID_INFORMATION msgid=00000000
Apr 16 13:47:11 LINUXHOST pluto[12025]: "WINHOST_Conn" #14: received and ignored informational message
Apr 16 13:47:12 LINUXHOST pluto[12025]: "WINHOST_Conn" #14: ignoring informational payload, type INVALID_ID_INFORMATION msgid=00000000
Apr 16 13:47:12 LINUXHOST pluto[12025]: "WINHOST_Conn" #14: received and ignored informational message
Apr 16 13:47:26 LINUXHOST pluto[12025]: "WINHOST_Conn" #14: received Delete SA payload: replace IPSEC State #16 in 10 seconds
Apr 16 13:47:26 LINUXHOST pluto[12025]: "WINHOST_Conn" #14: received and ignored informational message
Apr 16 13:47:31 LINUXHOST pluto[12025]: "WINHOST_Conn" #14: ignoring informational payload, type INVALID_ID_INFORMATION msgid=00000000
Apr 16 13:47:31 LINUXHOST pluto[12025]: "WINHOST_Conn" #14: received and ignored informational message
Apr 16 13:47:36 LINUXHOST pluto[12025]: "WINHOST_Conn" #30: initiating Quick Mode PSK+ENCRYPT+TUNNEL+DONTREKEY+UP+IKEv2ALLOW+SAREFTRACK to replace #16 {using isakmp#14 msgid:219d57e8 proposal=defaults pfsgroup=no-pfs}
problem is the windows server is the recipient in these transactions.

ASA5500: TCP state bypass for traffic, coming from IPsec tunnel

Hello!
We have problems on central firewall with restricting traffic coming from remote office from IPsec. (The network sheme is attached)
All branch offices are connected to central asa though IPsec.
The main aim is to rule access from branch offices only on the central firewall, NOT on each IPsec tunnel
According to the sheme:
172.16.1.0/24 is on of the branch office LANs
10.1.1.0/24 and 10.2.2.0/24 are central office LAN
The crypto ACL looks like permit ip 172.16.1.0/24 10.0.0.0/8
The aim is to
restrict access from 172.16.1.0/24 to 10.1.1.0/24
When packets are generated from host 10.1.1.10 to 172.16.1.0/24 all is ok - they are dropped by acl2
When packets are generated from 172.16.1.0/24 to 10.1.1.10 they are not dropped by any ACL - the reason is stateful firewall - traffic bypasses all access lists on a back path
I thought that TCP State Bypass feature can solve this problem and disable stateful firewall inspection for traffic coming from 172.16.1.0/24 to 10.1.1.0/24, but it didn't help.
The central asa 5500 is configured according to cisco doc http://www.cisco.com/en/US/docs/security/asa/asa82/configuration/guide/conns_tcpstatebypass.html
access-list tcp_bypass_acl extended permit tcp 172.16.1.0 255.255.255.0 10.1.1.0 255.255.255.0
class-map tcp_bypass_map
description "TCP traffic that bypasses stateful firewall"
match access-list tcp_bypass_acl
policy-map tcp_bypass_policy
class tcp_bypass_map
set connection advanced-options tcp-state-bypass
service-policy tcp_bypass_policy interface outside
service-policy tcp_bypass_policy interface inside
Does anyone know, how to make TCP State Bypass works properly?

I understand the pain of creating diffrent crypto for diffrent tunnels but i never come across better solution. However TCP state bypass is not going to help in regards to restrict access. TCP state bypass is a way to for FW to act like router which does not do statefull and I dont think that fits in your scenario.
You can still control access on center site by using vpn-filters.
http://www.cisco.com/en/US/products/hw/vpndevc/ps2030/products_configuration_example09186a00808c9a87.shtml
Thanks
Ajay

GRE traffic can not pass through LRT224 IPSec Tunnel

Hi,
We have a trouble when using Cisco Router GRE tunnel plus LRT224 IPSec Gateway-Gateway Tunnel.
We found after reboot, GRE packets can not pass trough LRT224 IPSec tunnel. need to restart serval time then gre will back to normal.
Besides that, GRE keepalive packets can not pass trough LRT224 IPSec Tunnel.
please help. I had tried to upgrade to latest firmware version.
Firmware Version : v1.0.3.09 (Dec 26 2014 14:28:46)
A-END:
interface Tunnel1
ip address 10.216.80.105 255.255.255.252
ip mtu 1400
ip nat outside
ip virtual-reassembly in
ip tcp adjust-mss 1360
ip ospf network point-to-point
ip ospf hello-interval 3
ip ospf cost 10000
tunnel source 10.216.81.2
tunnel destination 10.216.80.90
end
B-END:
interface Tunnel11
ip address 10.216.80.110 255.255.255.252
ip mtu 1400
ip tcp adjust-mss 1360
ip ospf network point-to-point
ip ospf cost 10000
ip ospf hello-interval 3
tunnel source 10.216.80.91
tunnel destination 10.216.81.3
end
CISCO2911 <> LRT224 <> INTERNET <> LRT224 <> CISCO 2621
San

Can you post the results from the below command for the Cisco Routers?
IOS Command: "sh version"
Why not static route without NAT through the LRT224 IPSec VPN?
Just curious why did you use LRT224's for the Site to Site VPN instead of the Cisco Routers?
Please remember to Kudo those that help you.
Linksys
Communities Technical Support

IPSEC Tunnel Failover MPLS

Similar Messages

Maybe you are looking for