IPv6 en de Cisco UCS B - Series

Los Cisco UCS B - Series soporta ipv6?

Hello Mario,
If your question is towards UCS management interfaces (FI and VIP interfaces) supporting IPv6 addresses - the answer is NO, UCS currently does not supports IPv6.
This is on the roadmap but nothing commited as of now.
./Abhinav

Similar Messages

  • Lync 2013 Standard Edition on Cisco UCS E-Series

    Hello,
    We have a working Lync 2013 deployment:
    - Front-End Enterprise Pool consisting of 3 FE servers
    - one Edge Server
    - one Back-End server
    - one Mediation Server
    - one IP PBX gateway, where ITSP's SIP trunks end.
    Because we have geographically distributed offices, we are considering deploying of branch offices deployments.
    Technet recommends to use SBA for branch offices where there are less than 1000 users. But in case of WAN outage, no conferencing will be available for branch users.
    Lync 2013 Standard edition branch deployment would offer all Lync features in case of WAN outage.
    In every branch, we consider deploying a Cisco ISR G2 router for terminating branch SIP trunks. This equipment have option to add Cisco UCS E-Series blade that supports CPU with hardware virtualization and supports decent amount of RAM (up to 16GB and up
    to 48GB).
    Have anyone experience with deploying Lync Standard Edition on this equipment - Cisco UCS E-Series blades? In every branch office there are up to 50 - 500 users that will use Lync.
    Thanks,
    Andrei Moraru Endava

    Hi,
    I don’t think you can deploy Lync server 2013 on Cisco UCS E-Series blades.
    Here is a link below of “System Requirements for Servers Running Lync Server 2013” may help you:
    http://technet.microsoft.com/en-us/library/gg398588.aspx
    Best Regards,
    Eason Huang
    Eason Huang
    TechNet Community Support

  • Just like HP servers, does Cisco UCS C-Series Standalone supports Network Fault Tolerance ?

    Just like HP servers, does Cisco UCS C-Series Standalone supports Network Fault Tolerance ? if yes then, where can i find this option
    Windows :- 2k8 R2

    Just like HP servers, does Cisco UCS C-Series Standalone supports Network Fault Tolerance ? if yes then, where can i find this option
    Windows :- 2k8 R2

  • Certification of Cisco UCS B-Series blades

    Are there any plans for certification of the Cisco UCS B-series blades?
    As far as i can find on the novell website they are already certified for SLES11 from Novell.
    Greetings, Stefan Dietz

    Hi Stefan,
    yes, we will certify CISCO hardware. Hopefully this will happen during the next 6 months. I cannot give more specific information at the moment. The SLES11 certification from SAP will also be available soon (see SLES11 thread in this forum as well).
    Thanks,
      Hannes

  • Ask the Expert: Cisco UCS B-Series Latest Version New Features

    Welcome to this Cisco Support Community Ask the Expert conversation. This is an opportunity to learn and ask questions about the Cisco UCS Manager 2.2(1) release, which delivers several important features and major enhancements in the fabric, compute, and operational areas. Some of these features include fabric scaling, VLANs, VIFs, IGMP groups, network endpoints, unidirectional link detection (UDLD) support, support for virtual machine queue (VMQ), direct connect C-Series to FI without FEX, direct KVM access, and several other features.
    Teclus Dsouza is a customer support engineer from the Server Virtualization team at the Cisco Technical Assistance Center in Bangalore, India. He has over 15 years of total IT experience. He has worked across different technologies and a wide range of data center products. He is an expert in Cisco Nexus 1000V and Cisco UCS products. He has more than 6 years of experience on VMware virtualization products.  
    Chetan Parik is a customer support engineer from the Server Virtualization team at the Cisco Technical Assistance Center in Bangalore, India. He has seven years of total experience. He has worked on a wide range of Cisco data center products such as Cisco UCS and Cisco Nexus 1000V. He also has five years of experience on VMware virtualization products.
    Remember to use the rating system to let Teclus and Chetan know if you have received an adequate response. 
    Because of the volume expected during this event, our experts might not be able to answer every question. Remember that you can continue the conversation in the Data Center community, under subcommunity Unified Computing, shortly after the event. This event lasts through May 9, 2014. Visit this forum often to view responses to your questions and the questions of other Cisco Support Community members.

    Hi Jackson,
    Yes its is possible.    Connect the storage array to the fabric interconnects using two 10GB links per storage processor.  Connect each SP to both fabric interconnects and configure the ports on the fabric interconnect as “Appliance” ports from UCSM
    For more information on how to connect Netapp storage using other protocols like iSCSI or FCOE  please check the url below.
    http://www.cisco.com/c/en/us/products/collateral/servers-unified-computing/ucs-6100-series-fabric-interconnects/whitepaper_c11-702584.html
    Regards
    Teclus Dsouza

  • Error Compilation MIBs Supported for Cisco UCS C-series software release 1.4(3) and later releases on IBM Director 6.3.2

    Hi,
    I have an IBM director 6.3.2 on a Windows Server 2008R2
    I try to install the MIB for manage Cisco UCS C-460 server.
    I downloaded the mib on the cisco ftp.
    the files extension was my. I cahgne it to .mib. For the moment I success to import some ones.
    But when I try to install Cisco-Unified-Computing-TC-MIB, I have got the error in the join file.
    Ho can I fix this issue...

    Hi,
    I have an IBM director 6.3.2 on a Windows Server 2008R2
    I try to install the MIB for manage Cisco UCS C-460 server.
    I downloaded the mib on the cisco ftp.
    the files extension was my. I cahgne it to .mib. For the moment I success to import some ones.
    But when I try to install Cisco-Unified-Computing-TC-MIB, I have got the error in the join file.
    Ho can I fix this issue...

  • Error: Failed to parse path in URl (Cisco UCS 6100 Series Fabric Interconnect)

    I have to shut down parts of my network due to an electrical outage this weekend. I have a Cisco UCS 6100 Server Fabric Interconnect. I am trying to backup the configuration. This is the command I am using create backup tftp://*.24.1.88 full-state enabled.  The error I receive is Error: failed to parse URI.  Which I believe URI means URL.

    Hi Parakiteiz,
    Looks like the format is incorrect and you have an extra 't' on the tftp command you provided.  Please take a look at the link below for configuration assistance.
    Creating backup operaiton.
    http://www.cisco.com/c/en/us/td/docs/unified_computing/ucs/sw/cli/config/guide/1-1-1/b_CLI_Config_Guide_1_1_1/CLI_Config_Guide_1_1_1_chapter38.html#task_4704260519853629974
    Please let me know if this help

  • IPv6 Support on Cisco UCS 6248UP Device

    Hi,
    We are in process of implementing IPv6 in our production environment and wanted to know what needs to be done on UCS level to achive the same ?
    We have Cisco 4948 and Nexus 3048 switches in our production environment above 6248 switch
    Thanks,
    Amit Vyas           

    Starting with 2.2.1b (El Capitan) IPv6 is supported (don't forget, Fabric Interconnect is a L2 switch, no L3 = routing)
    IPv6 Management Support:
    All 3 IP addresses  (2 physical and 1 cluster) are now able to have IPv6 addresses as are the new CIMC “in band” addresses. Services such as NTP, DNS are also reachable via IPv6.

  • Ask the Expert : Initial Set Up and LAN Connectivity for Cisco UCS Servers

    Welcome to the Cisco Support Community Ask the Expert conversation. This is an opportunity to learn and ask questions about related to the initial setup of UCS C & B Series which include LAN connectivity from the UCS perspective with Cisco subject matter expert Kenny Perez.
    In particularly, Kenny will cover topics such as: ESXi/Windows  installations, RAID configurations (best practices for good performance and configuration), VLAN/Jumbo Frames configuration for B series and C series servers, Pools/Policies/Upgrades/Templates/Troubleshooting Tips for blade and rack servers, Fabric Interconnects configuration, general compatibility of Hardware/Software/drivers amongst other topics
    Kenny Perez is a technical leader in Cisco Technical Assistance Center, where he works in Server Virtualization support team. His main job consists of supporting customers to implement and manage Cisco UCS B series and C series. He has background in computing, networking, and Vmware ESXi and has 3+ years of experience support UCS servers and is VCP certified.
    Remember to use the rating system to let Kenny know if he has given you an adequate response. 
    This event lasts through October 10th, 2014. Visit this forum often to view responses to your questions and the questions of other Cisco Support Community members.

    Hi,
    Actually  we have UCS 6248 fabric interconnect - first twelve ports are enabled  and same in Cisco UCS Manager.
    But when more port will be active by expansion module  then UCSM can manage that too or need any other licence  for UCSM too?

  • Cisco UCS components and Heartbleed bug

    I was reading about Cisco products affected by heartbleed vulnerability at following Cisco security advisory
    http://tools.cisco.com/security/center/content/CiscoSecurityAdvisory/cisco-sa-20140409-heartbleed#@ID
    I couldn't find whether below products/components are affected by this vulnerability.. can someone confirm if these products/components are vulnerable to heartbleed?
    Cisco UCS Manager
    Cisco Integrated Management Controller (CIMC)
    Cisco UCS Blade Chassis
    tia

    I agree that phrasing is a bit off, note that the notice is talking about _products_ affected (or not), not particular _components_ of a product. 
    UCS seems to be off the hook. Not affected are: 
    Cisco UCS B-Series (Blade) Servers
    Cisco UCS C-Series (Stand alone Rack) Servers
    Cisco UCS Central
    Cisco UCS Fabric Interconnects
    Cisco UCS Invicta Series Solid State Systems
    CIMC and UCSM would be part of FI or B-or-C-series, etc.

  • Cisco UCS 6248 and Dell EQ 6510x

            We have a Dell EQ 6510x we have in production and we are about to power on a Cisco UCS B series chassis and a pair of 6248UP FIs. I'm planning to connect the 4 6510x 10G ports directly to the 6248 FIs and set them as Applicance Ports.
    My question is would be be better to connect the 6510x Primary controller's two 10G ports directly to FI-A and the standby controller 10G ports directly to FI-B, or stagger them? Stagger meaning Primary Controller one10G to FI-A and one 10G to FI-B then Standby controller one 10G to FI-A and one10G to FI-B. Thanks!

    Hello there,
    In your design always keep in mind that both UCS FI are separate switches, they always will talk each other by the upstream switch. The best pratice is connect anything that have to talk with UCS domain in the upstream switch.
    If there is no option to do so, you can connect through the FIs, using a appliance port. In your case I believe that connect stagger mode is the best option, but I'm not sure, depends how your vnics are configured and if your Dell EQ can do port-channel in active-standby mode.

  • Cisco Unity Connection 8.X and Cisco UCS

    Hi
    We are in a planning phase for Unity Connection 8.X on Cisco UCS C-Series. The Cisco Unified Communications SRND 8.0 states that requires reserving one physical core per physical server.
    what does it really mean?

    See sample depiction below of applications and physical core usage on a server with 2 CPUs and 8 total physical cores. In white is the reservation of one physical core.
    Regards.

  • Cisco UCS

    Looking for a Design Guide where I can see how exactly design and configure Cisco UCS Blade Series Servers with (2) 2200 IOMs to Fabric Interconnects.  I like to see how Fabric Interconnects connect to Cisco FEXs.
    The design guides I have downloaded from Cisco only talks about Cisco FEXs at a very high level, not going into too much details how they connect to  Fabric Interconnects.
    As I understand correctly, Fabric Interconnects itself have may server ports that connect down to Chassis IOMs.  Trying to understand how Server Ports on Fabric Interconnects can work inconjuction with Cisco FEXs.

    Hi Abbasali,
    Cisco FEXes in UCS are use for C-Series server integrations. You won't be able use the FEXes to expand the number of ports on your fabric interconnect.
    C-Series integration documentation below
    http://www.cisco.com/c/en/us/td/docs/unified_computing/ucs/c-series_integration/ucsm2-1/b_UCSM2-1_C-Integration/b_UCSM2-1_C-Integration_chapter_01.html
    Don't forget to rate any useful posts.

  • Cisco UCS Managment interface

    Hi Dear
    Which is the function of the management interface of a Cisco UCS server? Only monitoring ?
    Best Regards

    Hi,
    The management interface present in the Cisco UCS C-Series is a out-of-band interface that provides to you access to Cisco Integrated Management Controller (CIMC) where you can perform all management/monitoring tasks related the hardware set.
    You can find more information about the CIMC in this link:
    http://www.cisco.com/c/en/us/support/servers-unified-computing/ucs-c-series-integrated-management-controller/tsd-products-support-series-home.html
    Regards,
    Richard

  • Nexus 5548 to UCS-C series network connectivity.

    Hi There,
    I am new to nexus world, mainly telecom side. I have a situation where a vendor like to deploy two Cisco UCS-C series servers for voice deployment.
    Each UCS C240 M3 server has 4 NICs, 2 nics bonded 802.1q will connect to primary nexus 5k switch and other two bonded will connect to secondary nexus switch. we have a vPC domain and no FEXes so we have to connect these two servers directly to Nexus 5ks.
    My question is it possible with teamed nics to coonect to 2 different nexus switches?
    Can anyone guide me how can I achieve this design? see attached.
    Thanks Much

    It will also depend on the Server network settings such as OS, software switch flavor and NIC teaming option on the server.
    x- if you run ESXi, then you may check out the following KB article. 
    http://kb.vmware.com/selfservice/microsites/search.do?language=en_US&cmd=displayKC&externalId=1004088
    x- if you use N1Kv, then you can use LACP or static port-channeling, but be sure to make it consistent on the upstream switches.
    hope it helps.
    Michael

Maybe you are looking for

  • 500 INternal server error on making ajax call to method of Application page

    HI I have a application page that have a method in code behond ..i need to call this method on usercontrol using jquey on client side..when i ma makeing the call to method using $.Ajax({definiotion}); then it gives me error 500 internal server error

  • Inbound ORDERS05, Ship-to party PO number

    Hello, we're trying to include the ship-to party's PO number in segment E1EDP02, qualifier 044 in an inbound ORDERS05 IDoc. However the data doesn't appear in the sales order. If we do the same on the header level and use E1EDK02, 044 instead it work

  • Iphone4s; Contacts : I want to order my contacts through their first name

    Good Day ! I just wanna ask if there is a possibility that i could sort my contacts through their first name because on my iphone (3Gs) it is possible. Example : John Smith                  Steve Jobbs -What I actually would like to happen is that th

  • T61 crashed and won't power back on

    He guys,  I have a 14" T61 (7662-CTO) that's been with me for 2 years. A few days ago, I was browsing and the laptop got very sluggish for a few minutes and then became unresponsive and crashed. I tried powering it back up, but it doesn't work. The b

  • Logic 8.01 is out!!!!

    Available via Software Update in OS X System Preferences. I cannot find any details of the changes. Richard