Ipv6 HSRP gloabl unicast address on cisco 3560 switch

Dear Team,
We are using cisco 3560 switch. Now we are going to implement ipv6 in our network. But we are not disturbing to existing ipv4. my question is 1) Can we confiure the global unicast ipv6 address in ipv6 HSRP and 2) can cisco 3560 switch will support ipv4 and ipv6 standby group on same SVI ?                 

YES

Similar Messages

  • Embeded Event Manager on cisco 3560 switch

    Can someone help me please? I have EEM configured on cisco 3560 switch. The configuration is below. I want that switch inform me through email when device with particilular IP address become unavailable. For some reason this configuration is not good and I can't tell why. I already try to debug this with debug event manager action mail but didn't see any output .
    ip sla 11
    icmp-echo ip address
    frequency 20
    ip sla schedule 11 life forever start-time now
    event manager applet device-TEST
    event snmp oid 1.3.6.1.4.1.9.9.42.1.2.9.1.6.11 get-type exact entry-op lt entry-val "2" poll-interval 20
    trigger occurs 5 period 120
    action 02.0 mail server "ip address" to "[email protected]" from "[email protected]" subject "device is down"

    The mail part looks good, I'm not sure you are hitting the trigger right.
    Why not do a track on the ip sla instead of the snmp stuff?
    Here's a good example of that.
    https://learningnetwork.cisco.com/blogs/network-sheriff/2009/06/19/writing-your-first-eem-applet

  • MTU Size Issue on Cisco 3560 Switch

    Could anybody tell me how to change MTU Size on a Cisco 3560 Switch.i mean to say whether it is to be changed on FastEthernet Interfaces or on VLAN 1 or on Global Configuration Mode and with which Command to change it.

    I am using MPLS on my Routers and the MTU size i have set on my Router Interfaces is 1524.
    When i do a normal ping from Customer's one site to another (where my Traffic has to pass through this Switch VLAN)i get a reply , but when a Ping with a Byte Size of 1500 or more the Packets get completely dropped.
    I think due to MTU Mistach bet. Switch and Router the Packets r getting droped,that is why i was trying to change it.
    could the Packets get dropped because of this reason.Please suggest.

  • DHCP and voice vlan on Cisco 3560 switch

    Greetings,
    I'm setting up a Cisco 3560 switch for voice and data comms. I'm looking for documentation with best practice guidelines for the following requirements.
    1. Using the Cisco 3560 as a DHCP server - Config examples.  Do I need to use different subnets for the voice and data vlans?
    2. Layer 2 CoS QoS  - I'm connecting Aastra phones as well as notebooks - I've been told that Aastra also makes use of the voice vlan config through LLDP and that Aastra phones supports CDP.
    Your assistance will be appreciated.

    Hi ,
    Cisco recommends that you have a separate vlan for  voice and data with different ip subnets for voice and data. You will need to configure the dhcp pool accordingly.
    Here is the config guide for setting up IOS DHCP server:
    http://www.cisco.com/en/US/docs/ios/12_0t/12_0t1/feature/guide/Easyip2.html
    Here is the LAN qos recommendations:
    http://www.cisco.com/en/US/docs/voice_ip_comm/cucm/srnd/7x/netstruc.html#wp1044009

  • Multilayer Cisco 3560 Switched network

    Hi,
    I have a multilayer Cisco 3560 network. All sites are connected to each other using RIP V2. The area marked in red is what we are having an issue with.
    1. We have remote sites connected by microwave links using Cisco 3560.
    2. In the attached image "Site-1" inherits all the configuration from the Headoffice. They also get their internet connection from the Headoffice over the " 256Kbps DSL-DATALINK".
    3. The area marked in red are the 2 sites, they were connected to each other using a data link.
    4. The 100 Mbps microwave links were commissioned lately so we want to use these links for our Internet + Data connections.
    5. HEAD OFFICE switch is running the VTP Domain.
    Question
    1. I have rip version 2 running how do I get "SITE-1" to share the internet connection from Headoffice over the Wireless Links
    2. Site-1 should get the IP address from the HeadOffice DHCP server over the wireless links.
    3. The "DSL-DATALINK" should work as a backup/redundant link. If my 100 Mbps link is down it should automatically switch to the DSL link.
    Kindly give me your expert comments/suggestions in how do I go about achieving the above.
    Regards
    Sarfaraz

    RIP works on hop-count and it will prefer the DSL connection over the Wireless link (1 hop vs 4 hops).
    You can alter this behavior by creating an offset list on routes incoming the data link.
    router rip
    version 2
    offset-list 0 in 5 [data link interface]
    http://www.cisco.com/univercd/cc/td/doc/product/software/ios124/124cr/hirp_r/rte_rih.htm#wp999452
    You need to this on both routers (site1 and HQ).

  • Configuring rcp on ciscoworks LMS 2.5 and cisco 3560 switch

    Dear All,
    i am having LMS 2.5 and nearly 50 cisco 3560 in my network. And I want to configure rcp. How can I do it. Kindly help
    regards,
    RAHIL KHAN

    Have a look at this link for the server:
    http://www.cisco.com/en/US/docs/net_mgmt/ciscoworks_resource_manager_essentials/4.0/user/guide/swmgt.html#wp1328314
    For the device you'll need something like:
    username cwuser password 7 000C1C0A05
    ip rcmd rcp-enable
    ip rcmd remote-host cwuser 172.17.246.221 cwuser enable
    ip rcmd remote-username cwuser

  • Cisco 3560 switch| mls qos trust dscp question

    Hi everybody
    Hi everybody .
    Please consider the following example:
    3560 sw f1/1--------trunk---SW2
    3560 sw
    f1/1
    mls qos trust dscp
    3560 is using default cos-dscp map, assume a 3560 receives a frame carrying IP packet on f1/1 with COS 4, what will 3560 switch do?
    1) will it use its default cos --dscp map  ( cos 4--.dscp 32) and rewrite 32 in dscp field  of the packet in the frame and provide PHB for dscp 32 ?
    Much appreciated!!
    Have  a great weekend.

    Hi
    No it will not trust the cos value, because You have configured to trust dcsp. So, the switch will trust the dcsp value in the incoming frame.
    /Mikael

  • Physical position of backup Cisco 3560 switch in relation to other produciton switches

    We currently have three 3560 switches connected to each other using SPF interconnect cables. I have a backup switch ready in the event one of the three switches fails. I'd like to keep the backup switch configured and in the rack connected to the three switches. If a switch fails, do the interconnect cables have to be routed in the same way they're currently setup or can they be connected in any order. In other words, if I have the replacement switch in the rack at the bottom with the other three switches and the top switch fails, after loading the config of the top switch onto the replacement switch, can I keep the cables from the second switch connected to the third switch and run the interconnect cables from the failed switch, now switch 1, to the third switch, which is situated in the rack just above the replacement switch? 
    Thanks in advance. 

    Disclaimer
    The Author of this posting offers the information contained within this posting without consideration and with the reader's understanding that there's no implied or expressed suitability or fitness for any purpose. Information provided is for informational purposes only and should not be construed as rendering professional advice of any kind. Usage of this posting's information is solely at reader's own risk.
    Liability Disclaimer
    In no event shall Author be liable for any damages whatsoever (including, without limitation, damages for loss of use, data or profit) arising out of the use or inability to use the posting's information even if Author has been advised of the possibility of such damage.
    Posting
    For 3560s, what SPF ports you use doesn't really matter.
    If the backup will be a cold spare, you may need to worry about port configurations, before you connect it.
    If the backup will be warm spare, again, you can interconnect the SPF ports however you like.  If, though, you create any L2 loops, you need something to break the loop, e.g. STP, FlexLink.
    If you want intentional redundancy, the simplest configuration would be a ring, and assuming the backup is just a warm spare, a root switch defined with the other two non-backup switches connected to it (on the ring).  (The backup would connect to the two non-root switches.)
    Besides a ring topology for redundancy, you might setup a dual star topology, or as you only have four switches, even a full mesh.

  • Service-policy output not working in Cisco 3560 switch

    We got some Cisco catalyst 3560 that we want to control the bandwidth
    on the ports. Can this be done, and how do i do it?
    Ive got 3550s that can do policy-map with the interface command;
    service-policy output(and input) <policyname>
    But 3560 only seems to handle service-policy input.
    If i try to configure output, it says the following:
    SW(config-if)#service-policy output 4mbit-out
    police command is not supported for this interface
    Configuration failed!
    Warning: Assigning a policy map to the output side of an interface not
    supported
    Any workarounds or new ways to accomplish bandwith-control on a 3560 ?
    regards,
    Rajib

    The 3560 & 3750 (& 2960) don't support egress policy-maps. They do however support queueing so it is possible to achieve similar results by applying an ingress policer to your user ports to classify (& police?) the traffic, at the egress port you can then queue the traffic based on it's DSCP or CoS value that it was classified with (same as 3550).
    It is also possible to restrict the bandwidth in use at an egress port with the interface command 'srr-queue bandwidth limit <10-90>' where 10-90 represents a percentage of the links bandwidth. For example if you want to restrict a 100Mbps port to 10Mbps you would use the command 'srr-queue bandwidth limit 10'
    HTH
    Andy

  • Can cisco 3560 switch act as wireless controlrer

    wireless issue

    Not 3560, but 3650 can do that
    http://www.cisco.com/c/en/us/products/collateral/switches/catalyst-3650-series-switches/data_sheet_c78-729449.html
    If you have 3650 model & having some issue, then refer below post that may help you. Even though it refer 3850 configuration should be very similar on 3650
    http://mrncciew.com/2013/09/29/getting-started-with-3850/
    HTH
    Rasika
    **** Pls rate all useful respones ****

  • NTP Issue on cisco 3560 switch

    Hi all 
    Here is my ntp configuration 
    clock timezone GMT 4
    clock summer-time UAE recurring
    ntp server 192.168.10.254 version 2 prefer
    end
    sh ntp status 
    Clock is unsynchronized, stratum 16, no reference clock
    nominal freq is 119.2092 Hz, actual freq is 119.2092 Hz, precision is 2**17
    reference time is 00000000.00000000 (04:00:00.000 GMT Mon Jan 1 1900)
    clock offset is 0.0000 msec, root delay is 0.00 msec
    root dispersion is 0.00 msec, peer dispersion is 0.00 msec
    -SW1#sh ntp associations
          address         ref clock     st  when  poll reach  delay  offset    disp
     ~192.168.10.254   0.0.0.0          16     -    64    0     0.0    0.00  16000.
     * master (synced), # master (unsynced), + selected, - candidate, ~ configured
    -SW1#
    Please help me what i have did wrong 
    regards
    raja

    You are still not answering the question.  
    Is the appliance, with IP Address 192.168.10.254, synchronized with a valid SNTP/NTP address or not. 
    Even if you enable NTP Master (which I personally don't recommend) and your appliance is NOT synchronized to a valid NTP source, then the appliance 192.168.10.254 can potentially broadcast the WRONG time to all the appliance.  Since you've forced all downstream appliances to synchronize with a source that has the wrong NTP data (using the command "ntp master") all your network equipment will be sporting the wrong time.

  • Communication problem between Cisco 3560 and Cisco SG300.

    Dear Support,
    I have a Cisco SG300 and Cisco 3560 switches.
    3560 is my Core Switch and SG300 is access switch.
    From 3560 VLAN information is not passed to SG300.
    3560 Configuration:
    interface GigabitEthernet0/23
    switchport trunk encapsulation dot1q
    switchport trunk allowed vlan 1,2,10,11
    switchport mode trunk
    SG300 Configuration:
    interface gigabitethernet49
    spanning-tree link-type point-to-point
    switchport mode general
    switchport general allowed vlan add 2,10-11 tagged
    macro description switch
    Please suggest how this issue is resolve.
    Regards,
    JItesh Mahajan.

    Dear Aleksandra,
    Below Configuration is right or wrong for 3560 and SG300.
    3560 Configuration:
    interface GigabitEthernet0/23
    switchport trunk encapsulation dot1q
    switchport trunk allowed vlan remove VLAN 1
    switchport native vlan 1
    switchport trunk allowed vlan 1,2,10,11
    switchport mode trunk
    SG300 Configuration:
    interface gigabitethernet49
    spanning-tree link-type point-to-point
    switchport mode general
    switchport general allowed vlan add 2,10-11 tagged
    macro description switch
    Regards,
    JItesh Mahajan.

  • Ivette manzur : Interface errors problems on cisco 3560

    Hello,
    I have a problem on one of the interfaces on a cisco 3560 switch. In fact, I set up a monitoring network recently (cacti), and I have a significant number of errors on the interfaces. the problem is that when I do a sh interface I see no errors, and even by making a clear counters it does not solve my problem .. I also changed the wiring with cat 6 cables but nothing has changed ..
    What are the main causes of errors on an interface of a switch? what should I do in this case?
    Thank you for your help in advance
    ivette manzur

    Hello,
    I've a e61i and I experience a similar problem. My phone work very well on WiFi network with no encryption as well as 64-bit wep.
    At home I've 2 wireless routers, both encrypted at 128 bits, one with WEP and the other with WPA. On both of them I can correctly obtain an IP thru DHCP, but the traffic do not go thru.
    By using IfInfo I think I discovered the reason of the problem (unless IfInfo is not working properly...) and it seems a bug related to the netmask, broadcast and gateway settings. The router is 192.168.15.1 and this is what I get:
    1) DHCP case -- I get two IP adresses: the 169.254.x.x and the one assigned to the router. DNS is also set properly, but both gateway, broadcast and netmask are set to 0.0.0.0 for both IPs.
    IP Addr: 169.254.162.106
    Netmask: 0.0.0.0
    Broadcast: 0.0.0.0
    Gateway: 0.0.0.0
    DNS1: 192.168.15.1
    IP Addr: 192.168.15.100
    Netmask: 0.0.0.0
    Broadcast: 0.0.0.0
    Gateway: 0.0.0.0
    DNS1: 192.168.15.1
    2) Static IP 192.168.15.64, netmask set to 255.255.255.0 and gateway and DNS set to 192.168.15.1. The 169.254.x.x disappears and I get only one IP which is set to:
    IP Addr: 192.168.15.64
    Netmask: 0.0.0.0
    Broadcast:192.168.15.255
    Gateway: 192.168.15.1
    DNS1: 192.168.15.1
    So in conclusion, it seems that with 128bit encryption, in the DHCP case gateway, broadcast and netmask are not assigned correctly! While in the Static IP case the netmask is still not assigned correctly!!!
    Hope this can help...
    --AP

  • MAC Addressess not showing on my new 3560 switch

    I have a Cisco 3560 (Switch B) switch I just introduced into my network.  The gigabit ports are trunked from another switch (Switch A) to a Cisco 6509 WS (Main Switch).
    crpf4bsw3#show cdp neighbors
    Device ID            Local Intrfce         Holdtme   Capability    Platform   Port ID
    crpf4bsw2.mdch.com
                        Gig 0/1               124            S I      WS-C3560-4Gig 0/4
    crpcorsw1.mdch.com
                        Gig 0/4               127           R S I     WS-C6509-EGig 2/8
    interface GigabitEthernet0/4
     switchport trunk encapsulation dot1q
     switchport trunk allowed vlan 1,19,124,150,160,164,168,224
     switchport mode trunk
     mls qos trust dscp
     spanning-tree link-type point-to-point
    interface GigabitEthernet0/1
     switchport trunk encapsulation dot1q
     switchport trunk allowed vlan 1,19,124,150,160,164,168,224
     switchport mode trunk
     mls qos trust dscp
     spanning-tree link-type point-to-point
    The trunk ports are working just fine.  I have configured all necessary remote management with no issues.  However, my access ports are not working.  I have set them up exactly the same as the adjacent switch A and it works just fine, but the same configuration on the new switch has not been able to pull IP information.  I have provided information as to how the switch access ports are configured on both Switch A (working) and Switch B (not working).  I should note that I tried this with a Cisco 7940 phone and it got stuck on "configuring IP" then I tried it with my laptop and it pulled a 169 IP address.  Both were direct connections into switch B.  When I run a show mac-address-table, neither device shows up in the table.  Only the gig port MACs.  Any thoughts? Please let me know if you need any more information.
    interface FastEthernet0/3
     switchport access vlan 124
     switchport mode access
     switchport voice vlan 224
     switchport port-security maximum 3
     switchport port-security
     switchport port-security aging time 2
     switchport port-security violation restrict
     switchport port-security aging type inactivity
     srr-queue bandwidth share 10 10 60 20
     srr-queue bandwidth shape  10  0  0  0
     mls qos trust device cisco-phone
     mls qos trust cos
     auto qos voip cisco-phone
     spanning-tree portfast
     spanning-tree bpduguard enable

    Hi Mike,
    It looks like you're guiding me in the right direction.  I did a "show port security interface fa0/2" on the new switch and nothing was out of the ordinary with the exception of the 0 MAC addresses learned.  But then I did a "show spanning tree vlan 224" Here's what I found:
    Switch A (existing switch):
    crpf4bsw2#show spanning-tree vlan 224
    VLAN0224
      Spanning tree enabled protocol rstp
      Root ID    Priority    4096
                 Address     0012.44cc.68e0
                 Cost        8
                 Port        1 (GigabitEthernet0/1)
                 Hello Time   2 sec  Max Age 20 sec  Forward Delay 15 sec
      Bridge ID  Priority    32992  (priority 32768 sys-id-ext 224)
                 Address     0013.60aa.7400
                 Hello Time   2 sec  Max Age 20 sec  Forward Delay 15 sec
                 Aging Time 300
    Interface        Role Sts Cost      Prio.Nbr Type
    Gi0/1            Root FWD 4         128.1    P2p
    Fa0/1            Desg FWD 19        128.3    Edge P2p
    Fa0/2            Desg FWD 19        128.4    Edge P2p
    Fa0/3            Desg FWD 19        128.5    Edge P2p
    Fa0/4            Desg FWD 19        128.6    Edge P2p
    Fa0/5            Desg FWD 19        128.7    Edge P2p
    Fa0/6            Desg FWD 19        128.8    P2p Peer(STP)
    Interface        Role Sts Cost      Prio.Nbr Type
    Fa0/7            Desg FWD 19        128.9    Edge P2p
    Fa0/8            Desg FWD 19        128.10   Edge P2p
    Fa0/9            Desg FWD 19        128.11   Edge P2p
    Fa0/10           Desg FWD 19        128.12   Edge P2p
    Fa0/11           Desg FWD 19        128.13   Edge P2p
    Fa0/12           Desg FWD 19        128.14   Edge P2p
    Fa0/13           Desg FWD 19        128.15   Edge P2p
    Fa0/15           Desg FWD 19        128.17   Edge P2p
    Fa0/19           Desg FWD 19        128.21   Edge P2p
    Fa0/20           Desg FWD 19        128.22   Edge P2p
    Gi0/4            Desg FWD 4         128.28   P2p
    Fa0/29           Desg FWD 19        128.33   Edge P2p
    Fa0/30           Desg FWD 19        128.34   Edge P2p
    Fa0/31           Desg FWD 19        128.35   Edge P2p
    Fa0/32           Desg FWD 19        128.36   Edge P2p
    Fa0/33           Desg FWD 19        128.37   Edge P2p
    Fa0/34           Desg FWD 19        128.38   Edge P2p
    Fa0/35           Desg FWD 19        128.39   Edge P2p
    Fa0/37           Desg FWD 19        128.41   Edge P2p
    Fa0/38           Desg FWD 19        128.42   Edge P2p
    Fa0/39           Desg FWD 19        128.43   Edge P2p
    Fa0/40           Desg FWD 19        128.44   Edge P2p
    Fa0/41           Desg FWD 19        128.45   Edge P2p
    Interface        Role Sts Cost      Prio.Nbr Type
    Fa0/42           Desg FWD 19        128.46   Edge P2p
    Fa0/43           Desg FWD 19        128.47   Edge P2p
    Fa0/44           Desg FWD 19        128.48   Edge P2p
    Fa0/45           Desg FWD 19        128.49   Edge P2p
    Fa0/46           Desg FWD 19        128.50   Edge P2p
    Switch B (new switch):
    Spanning tree instance(s) for vlan 224 does not exist.
    So with this new information, and with my trunk configurations above, what did you mean by a disconnect on the trunk?

  • Setting CoS value in 3560 switch

    Hello,
    Can someone help me how can I set the CoS value under policy map in Cisco 3560 switch IOS release 15.0. It gives me the option to set either IP Precedence or DSCP but there is no option for setting Class of Service (CoS).
    Please see attached screenshot for clarity. Thanks in advance.
    Tilawat

    Thanks Reza for responding. However, I want to assign the CoS value based on some classification specified in class map like MAC address. Therefore, I am considering this to be under policy map. How can I mark the traffic with some CoS value based on the classification. I just don't want to assign CoS to every frame that lands on an interface of the switch by adding CoS to the switch interface.
    Thanks,
    Tilawat

Maybe you are looking for

  • When I try to connect to itunes this appears: An unknown error occurred (-3221). What should I do?

    When I try to connect to iTunes Store via iTunes, this pops up: An unknown error occurred (-3221). What does this mean? What should I do to connect?

  • Trouble importing .mxf files into Premiere Pro CS6

    Having problems importing MXF. file types into my Premiere CS6 project. I will go to import the folder and the yellow loading bar will come up to say that it's importing. Then it will freeze and the color wheeled loading symbol will come up (I'm usin

  • Preferences, Screen Saver - Not Responding

    Hey everyone, I am having trouble with a computer that's not responding amongst other things. It started with iPhoto....when opened it would take forever to load and then basically couldn't do anything within it. I made a new library and opened it an

  • Data Buffers and VMware

    I have virtualized a bare metal db machine.   The vm host is esxi 5.5.  The disk subsystem, as it pertains to sql, on vmware is much faster than bare metal.  However, cashed operation is taking much longer.  For instance, I have a query which joins 2

  • Single and Double Underlines When Showing Cross Tab Data

    Hi, I am trying to generate an XML Publisher rtf report in which I need to show the cross tab data which is in number format underlined and totals as double underlined. Is there a way to do that; I am using XML Publisher 5.6.2 version , Build 45 and