IPV6 on Cisco 3620 Router

Dear Sir,
I have a Cisco 3620 Router with 32 mb Dram and 16 MB flash.
Which IOS will support IPV6 addressing on this Router.
Thanks/Regard
Atul

Hello Atul,
the only way to get the IOS is to download it from CCO, or to get it from a reseller or partner.
Here is the link to the CCO download file:
c3620-is-mz.122-15.T16.bin
http://www.cisco.com/cgi-bin/Software/Iosplanner/Planner-tool/iosresult.cgi?get_crypto=&data_from=&hardware_name=3620&software_name=IP%20PLUS&release_name=12.2.15T16&majorRel=12.2&state=:HW:RL:SW&type=Early%20Deployment
Obviously, your access level needs to be sufficient to download the IOS...
HTH,
GP

Similar Messages

  • Cisco 3620 Router IOS CCIE lab

    Dear Sir,
    I procured one Cisco 3620 Router for CCIE R&S Lab.
    Which IOS should I download from www.cisco.com to support 12.2T and IPV6.
    Waiting for reply..
    Thanks/Regards
    Atul

    Hi Atul,
    This link may help you with the same
    http://tools.cisco.com/ITDIT/CFN/jsp/index.jsp
    Regards,
    Ankur

  • Configuring Cisco 3620 router

    I am quite new and haven't worked before with Cisco router. I have a Cisco 3620 router with only one ethernet interface (FastEthernet 0/0).
    I want to configure it so that the router will have ip address of 192.168.2.2 (255.255.255.0). I am not using DHCP so all the machines in the network are configured manually.
    My running-config is as follows.
    version 11.3
    service timestamps debug uptime
    service timestamps log uptime
    no service password-encryption
    hostname router
    enable secret xxxx
    enable password xxxx
    controller T1 0/0
    framing esf
    linecode b8zs
    channel-group 0 timeslots 1-24 speed 64
    interface FastEthernet0/0
    ip address 192.168.2.2 255.255.255.0
    interface Serial0/0:0
    no ip address
    shutdown
    ip classless
    dialer-list 1 protocol ip permit
    dialer-list 1 protocol ipx permit
    line con 0
    line aux 0
    line vty 0 4
    password xxxx
    login
    end
    Can someone give advise on what should I use for default-gateway, default-network and route?
    I want to use name-server which has class B ip address. 131.x.x.x.
    If my router can route all the traffic to 131.x.x.y (gateway in the same LAN as router) then I can connect to Internet.
    Can someone tell me how to do this?
    Regards,
    Amar.

    Hi
    i feel u need to have 2 ethernet interfaces in your router to have the reachability to the 131.x.x.x series from your local lan which is in 192.168.2.x series..
    eventually u need to deploy nat to have this kinda access in place...
    if you got to have that you can configure one of your interface on 131.x.x.x series and configure it as a nat outside interface and keep faeth0/0 as ur inside interface.
    you need to configure up a access list and also the necessary overloading to achieve the connectivity.
    i think this link will def help u out to find more details about the scenario and config details about which i m mentionining over here..
    http://www.cisco.com/en/US/tech/tk648/tk361/technologies_tech_note09186a0080094831.shtml
    And again you can have the ip reachability using normal static ip route in your box..pointing to the ip which can be used to go out to the public/outside world..
    regds

  • XMODEM FAIL with no notice in 3620 router

    Cisco 3620 router 16M*4 DRAM,16MB+8MB Flash SIMM
    PCMCIA Slot1: No Card Present
    System Bootstrap, Version 11.1(20)AA2, EARLY DEPLOYMENT RELEASE SOFTWARE (fc1)
    Copyright (c) 1999 by cisco Systems, Inc.
    C3600 processor with 65536 Kbytes of main memory
    Main memory is configured to 32 bit mode with parity disabled
    device does not contain a valid magic number
    boot: cannot open "flash:"
    boot: cannot determine first file name on device "flash:"
    System Bootstrap, Version 11.1(20)AA2, EARLY DEPLOYMENT RELEASE SOFTWARE (fc1)
    Copyright (c) 1999 by cisco Systems, Inc.
    C3600 processor with 65536 Kbytes of main memory
    Main memory is configured to 32 bit mode with parity disabled
    rommon 1 > xmodem -c c3620-ik9o3s6-mz.123-26.bin
    Do not start the sending program yet...
    device does not contain a valid magic number
    dir: cannot open device "flash:"
    WARNING: All existing data in flash will be lost!
    Invoke this application only for disaster recovery.
    Do you wish to continue? y/n  [n]:  y
    Ready to receive file c3620-ik9o3s6-mz.123-26.bin ...
    C
    after transfer is complete,nothing shows up   so I restart the router
    System Bootstrap, Version 11.1(20)AA2, EARLY DEPLOYMENT RELEASE SOFTWARE (fc1)
    Copyright (c) 1999 by cisco Systems, Inc.
    C3600 processor with 65536 Kbytes of main memory
    Main memory is configured to 32 bit mode with parity disabled
    device does not contain a valid magic number
    boot: cannot open "flash:"
    boot: cannot determine first file name on device "flash:"
    previous xmodem doesn't work out?
    System Bootstrap, Version 11.1(20)AA2, EARLY DEPLOYMENT RELEASE SOFTWARE (fc1)
    Copyright (c) 1999 by cisco Systems, Inc.
    C3600 processor with 65536 Kbytes of main memory
    Main memory is configured to 32 bit mode with parity disabled
    PCMCIA Slot0: No Card Present
    System Bootstrap, Version 11.1(20)AA2, EARLY DEPLOYMENT RELEASE SOFTWARE (fc1)
    Copyright (c) 1999 by cisco Systems, Inc.
    C3600 processor with 65536 Kbytes of main memory
    Main memory is configured to 32 bit mode with parity disabled
    PCMCIA Slot1: No Card Present
    System Bootstrap, Version 11.1(20)AA2, EARLY DEPLOYMENT RELEASE SOFTWARE (fc1)
    Copyright (c) 1999 by cisco Systems, Inc.
    C3600 processor with 65536 Kbytes of main memory
    Main memory is configured to 32 bit mode with parity disabled
    device does not contain a valid magic number
    boot: cannot open "flash:"
    boot: cannot determine first file name on device "flash:"
    System Bootstrap, Version 11.1(20)AA2, EARLY DEPLOYMENT RELEASE SOFTWARE (fc1)
    Copyright (c) 1999 by cisco Systems, Inc.
    C3600 processor with 65536 Kbytes of main memory
    Main memory is configured to 32 bit mode with parity disabled
    rommon 1 > ?
    alias               set and display aliases command
    boot                boot up an external process
    break               set/show/clear the breakpoint
    confreg             configuration register utility
    cont                continue executing a downloaded image
    context             display the context of a loaded image
    cookie              display contents of cookie PROM in hex
    dev                 list the device table
    dir                 list files in file system
    dis                 disassemble instruction stream
    dnld                serial download a program module
    frame               print out a selected stack frame
    help                monitor builtin command help
    history             monitor command history
    meminfo             main memory information
    repeat              repeat a monitor command
    reset               system reset
    set                 display the monitor variables
    stack               produce a stack trace
    sync                write monitor environment to NVRAM
    sysret              print out info from last system return
    unalias             unset an alias
    unset               unset a monitor variable
    xmodem              x/ymodem image download
    rommon 2 > xmodem -c c3620-ik9o3s7-mz.123-22.bin
    Do not start the sending program yet...
    device does not contain a valid magic number
    dir: cannot open device "flash:"
    WARNING: All existing data in flash will be lost!
    Invoke this application only for disaster recovery.
    Do you wish to continue? y/n  [n]:  y
    Ready to receive file c3620-ik9o3s7-mz.123-22.bin ...
    Erasing flash at 0x317c0000
    program flash location 0x30310000
    then stuck here ,I restart it
    System Bootstrap, Version 11.1(20)AA2, EARLY DEPLOYMENT RELEASE SOFTWARE (fc1)
    Copyright (c) 1999 by cisco Systems, Inc.
    C3600 processor with 65536 Kbytes of main memory
    Main memory is configured to 32 bit mode with parity disabled
    boot: cannot determine first file name on device "flash:"
    System Bootstrap, Version 11.1(20)AA2, EARLY DEPLOYMENT RELEASE SOFTWARE (fc1)
    Copyright (c) 1999 by cisco Systems, Inc.
    C3600 processor with 65536 Kbytes of main memory
    Main memory is configured to 32 bit mode with parity disabled
    PCMCIA Slot0: No Card Present
    System Bootstrap, Version 11.1(20)AA2, EARLY DEPLOYMENT RELEASE SOFTWARE (fc1)
    Copyright (c) 1999 by cisco Systems, Inc.
    C3600 processor with 65536 Kbytes of main memory
    Main memory is configured to 32 bit mode with parity disabled
    PCMCIA Slot1: No Card Present
    System Bootstrap, Version 11.1(20)AA2, EARLY DEPLOYMENT RELEASE SOFTWARE (fc1)
    Copyright (c) 1999 by cisco Systems, Inc.
    C3600 processor with 65536 Kbytes of main memory
    Main memory is configured to 32 bit mode with parity disabled
    boot: cannot determine first file name on device "flash:"
    System Bootstrap, Version 11.1(20)AA2, EARLY DEPLOYMENT RELEASE SOFTWARE (fc1)
    Copyright (c) 1999 by cisco Systems, Inc.
    C3600 processor with 65536 Kbytes of main memory
    Main memory is configured to 32 bit mode with parity disabled
    rommon 1 >
    rommon 2 > dir flash:
             File size           Checksum   File name
      15120140 bytes (0xe6b70c)   0x7f2e    c3620-ik9o3s7-mz.123-22.bin (bad checksu
    m: 0x5bd5)
    rommon 3 >
    c3620-ik9o3s6-mz.123-26.bin is 16.3MB and c3620-ik9o3s7-mz.123-22.bin is 14.4MB ,and I have one 8MB and one 16MB Flash SIMM installed.Will it work this way?or something else is wrong?
    my last try with only one 16MB SIMM,still stuck after transferring
    rommon 2 > xmodem -c c3620-ik9o3s7-mz.123-22.bin
    Do not start the sending program yet...
             File size           Checksum   File name
      15120140 bytes (0xe6b70c)   0x7f2e    c3620-ik9o3s7-mz.123-22.bin (bad checksu
    m: 0x5bd5)
    WARNING: All existing data in flash will be lost!
    Invoke this application only for disaster recovery.
    Do you wish to continue? y/n  [n]:  y
    Ready to receive file c3620-ik9o3s7-mz.123-22.bin ...
    Erasing flash at 0x30fc0000
    program flash location 0x30660000
    stuck
    Thanks
    Problem solved I guess the flash partition info is somehow corrupted
    solution
    1.rommon   xmodem -r
    2.IOS   format flash
    3.IOS copy xmodem: flash:
    If not necessary,don't jerk around with a actual router   simulators are pretty much enough for a lot of things

    rommon 6 > xmodem -r c3620-ik9o3s7-mz.123-22.bin
    Do not start the sending program yet...
    Invoke this application only for disaster recovery.
    Do you wish to continue? y/n  [n]:  y
    Ready to receive file  ...
    Download Complete!
    program load complete, entry point: 0x80008000, size: 0xe6b5c8
    Self decompressing the image : #################################################
    ########################################################## [OK]
    Smart Init is enabled
    smart init is sizing iomem
      ID            MEMORY_REQ                 TYPE
                    0X00098670 public buffer pools
                    0X00211000 public particle pools
    TOTAL:          0X002A9670
    If any of the above Memory Requirements are
    "UNKNOWN", you may be using an unsupported
    configuration or there is a software problem and
    system operation may be compromised.
    Rounded IOMEM up to: 3Mb.
    adjusted iome size up to minimum size of: 0X00400000
    Using 6 percent iomem. [4Mb/64Mb]
                  Restricted Rights Legend
    Use, duplication, or disclosure by the Government is
    subject to restrictions as set forth in subparagraph
    (c) of the Commercial Computer Software - Restricted
    Rights clause at FAR sec. 52.227-19 and subparagraph
    (c) (1) (ii) of the Rights in Technical Data and Computer
    Software clause at DFARS sec. 252.227-7013.
               cisco Systems, Inc.
               170 West Tasman Drive
               San Jose, California 95134-1706
    Cisco Internetwork Operating System Software
    IOS (tm) 3600 Software (C3620-IK9O3S7-M), Version 12.3(22), RELEASE SOFTWARE (fc
    2)
    Technical Support: http://www.cisco.com/techsupport
    Copyright (c) 1986-2007 by cisco Systems, Inc.
    Compiled Wed 24-Jan-07 17:37 by ccai
    Image text-base: 0x60008B00, data-base: 0x61950000
    This product contains cryptographic features and is subject to United
    States and local country laws governing import, export, transfer and
    use. Delivery of Cisco cryptographic products does not imply
    third-party authority to import, export, distribute or use encryption.
    Importers, exporters, distributors and users are responsible for
    compliance with U.S. and local country laws. By using this product you
    agree to comply with applicable laws and regulations. If you are unable
    to comply with U.S. and local laws, return this product immediately.
    A summary of U.S. laws governing Cisco cryptographic products may be found at:
    http://www.cisco.com/wwl/export/crypto/tool/stqrg.html
    If you require further assistance please contact us by sending email to
    [email protected].
    cisco 3620 (R4700) processor (revision 0x81) with 61440K/4096K bytes of memory.
    Processor board ID 26883880
    R4700 CPU at 80MHz, Implementation 33, Rev 1.0
    Bridging software.
    X.25 software, Version 3.0.0.
    DRAM configuration is 32 bits wide with parity disabled.
    29K bytes of non-volatile configuration memory.
    16384K bytes of processor board System flash (Read/Write)
    %Error: Invalid partition size parameters(s).
    %Error: Requested partitions not valid.
    Press RETURN to get started!
    *Mar  1 00:00:03.299: %LINEPROTO-5-UPDOWN: Line protocol on Interface VoIP-Null0
    , changed state to up
    *Mar  1 00:00:06.671: %LINK-4-NOMAC: A random default MAC address of 0000.0c86.3
    880 has
      been chosen.  Ensure that this address is unique, or specify MAC
      addresses for commands (such as 'novell routing') that allow the
      use of this address as a default.
    00:00:14: %SYS-5-CONFIG_I: Configured from memory by console
    00:00:17: %SYS-5-RESTART: System restarted --
    Cisco Internetwork Operating System Software
    IOS (tm) 3600 Software (C3620-IK9O3S7-M), Version 12.3(22), RELEASE SOFTWARE (fc
    2)
    Technical Support: http://www.cisco.com/techsupport
    Copyright (c) 1986-2007 by cisco Systems, Inc.
    Compiled Wed 24-Jan-07 17:37 by ccai
    00:00:17: %SNMP-5-COLDSTART: SNMP agent on host 64E32 is undergoing a cold start
    I'll do a format and see what will happen.Actually I am not sure if i need to format a Flash SIMM,its not a PCMCIA card.
    64E32>en
    64E32#erase /?
    /all  /no-squeeze-reserve-space
    64E32#format /?
    % Unrecognized command
    64E32#erase /all ?
      nvram:  Filesystem to be erased (how can I format flash?)
    64E32#dir
    Directory of flash:/
    No files in directory
    16777212 bytes total (1657008 bytes free)
    64E32#dir flash:
    Directory of flash:/
    No files in directory
    16777212 bytes total (1657008 bytes free)
    64E32#copy xmodem flash:
    Source filename []? c3620-ik9o3s7-mz.123-22.bin
    Destination filename [c3620-ik9o3s7-mz.123-22.bin]?
    %Error copying flash:c3620-ik9o3s7-mz.123-22.bin (destination path is identical)  (I Google this and find nothing about it)
    64E32#

  • IPv6 on CIsco 7200 VXR series router

    Dear Friends,
    I want to know, whether cisco 7200vxr router support ipv6? I want to use both ipv4 and ipv6. In that case whats about the performance.
    Do i need IOS upgradation to acheive this implementation.

    Hi -
    Our s/w development group is in the process of implementing ipv6 support in our products, and would like to use our Cisco 2650XM running ITP s/w for ipv6 interoperability tests.
    However, it appears that ipv6 is not supported in this s/w version:
    ITP1#sh version
    Cisco IOS Software, C2600 Software (C2600-ITPK9-M), Version 12.4(15)SW2, RELEASE SOFTWARE (fc3)
    Technical Support: http://www.cisco.com/techsupport
    Copyright (c) 1986-2008 by Cisco Systems, Inc.
    Compiled Tue 23-Sep-08 19:48 by prod_rel_team
    ROM: System Bootstrap, Version 12.2(7r) [cmong 7r], RELEASE SOFTWARE (fc1)
    ITP1#config
    Configuring from terminal, memory, or network [terminal]?
    Enter configuration commands, one per line. End with CNTL/Z.
    ITP1(config)#ipv6 ?
    % Unrecognized command
    My question is: Can I use this s/w version on the 2650XM in an ipv6 network? Do I need to upgrade the s/w?
    Thanks,
    Matt

  • ASA 5510 with Cisco 2811 Router Behind it - Not forwarding traffic

    Hi all,
    Some might know that I have been dealing with an issue where I cannot seem to get forwarded packets to reach their destinations behind an ASA 5510 that has a Cisco 2811 connected directly behind it.
    Some examples that work.
    I can SSH into the ASA.
    I can SSH to the Cisco Routers behind the ASA.
    I cannot reach items beind the Cisco Routers.
    My Configuration is this (I am sure I included a bunch of info I didn't need to, but I am hoping it'll help!):
    I have a static Ip assigned to my Ouside Interface Ethernet 0/1
    It has an IP address of 199.195.xxx.xxx
    I am trying to learn how to shape network traffic (this is all new to me) via the ASA and the Routers to specific devices.
    The Inside Interface on the ASA is 10.10.1.1 255.255.255.252
    The Outside Interface on the 2811 is 10.10.1.2 255.255.255.252
    I can ping the router from the ASA. I can SSH through the ASA to the router.
    BUT I CANNOT ACCESS DEVICES BEHIND THE ROUTER.
    So, I wanted to BAM that statement above because I just don't kjnow where the issue is. Is the issue on the router or the ASA, my guess is, the router, but I just don't know.
    Here are my configs, helpfully someone can help.
    ASA errors on the ASDM when I try and hit resources; specifically a web device behind the ASA and the 2811. It's Ip address 192.168.1.5 it's listening on port 80.Static IP, not assigned via DHCP.
    6
    Feb 14 2014
    19:38:56
    98.22.121.x
    41164
    192.168.1.5
    80
    Built inbound TCP connection 1922859 for Outside:98.22.121.x/41164 (98.22.121.x/41164) to Inside:192.168.1.5/80 (199.195.168.x/8080)
    6
    Feb 14 2014
    19:38:56
    10.10.1.2
    80
    98.22.121.x
    41164
    Deny TCP (no connection) from 10.10.1.2/80 to 98.22.121.x/41164 flags SYN ACK  on interface Inside
    ASA5510# sh nat
    Auto NAT Policies (Section 2)
    1 (DMZ) to (Outside) source static ROUTER-2821 interface   service tcp ssh 2222
        translate_hits = 1, untranslate_hits = 18
    2 (Inside) to (Outside) source static ROUTER-2811 interface   service tcp ssh 222
        translate_hits = 0, untranslate_hits = 13
    3 (VOIP) to (Outside) source static ROUTER-3745 interface   service tcp ssh 2223
        translate_hits = 0, untranslate_hits = 3
    4 (Inside) to (Outside) source static RDP-DC1 interface   service tcp 3389 3389
        translate_hits = 0, untranslate_hits = 236
    5 (Inside) to (Outside) source static WEBCAM-01 interface   service tcp www 8080
        translate_hits = 0, untranslate_hits = 162
    Manual NAT Policies (Section 3)
    1 (any) to (Outside) source dynamic PAT-SOURCE interface
        translate_hits = 1056862, untranslate_hits = 83506
    ASA5510# show access-list
    access-list cached ACL log flows: total 0, denied 0 (deny-flow-max 4096)
                alert-interval 300
    access-list USERS; 1 elements; name hash: 0x50681c1e
    access-list USERS line 1 standard permit 10.10.1.0 255.255.255.0 (hitcnt=0) 0xdd6ba495
    access-list Outside_access_in; 5 elements; name hash: 0xe796c137
    access-list Outside_access_in line 1 extended permit tcp host 98.22.121.x object ROUTER-2811 eq ssh (hitcnt=37) 0x5a53778d
      access-list Outside_access_in line 1 extended permit tcp host 98.22.121.x host 10.10.1.2 eq ssh (hitcnt=37) 0x5a53778d
    access-list Outside_access_in line 2 extended permit tcp host 98.22.121.x object ROUTER-2821 eq ssh (hitcnt=8) 0x9f32bc21
      access-list Outside_access_in line 2 extended permit tcp host 98.22.121.x host 10.10.0.2 eq ssh (hitcnt=8) 0x9f32bc21
    access-list Outside_access_in line 3 extended permit tcp host 98.22.121.x interface Outside eq https (hitcnt=0) 0x385488b2
    access-list Outside_access_in line 4 extended permit tcp host 98.22.121.x object WEBCAM-01 eq www (hitcnt=60) 0xe66674ec
      access-list Outside_access_in line 4 extended permit tcp host 98.22.121.x host 192.168.1.5 eq www (hitcnt=60) 0xe66674ec
    access-list Outside_access_in line 5 extended permit tcp host 98.22.121.x object RDP-DC1 eq 3389 (hitcnt=3) 0x02f13f4e
      access-list Outside_access_in line 5 extended permit tcp host 98.22.121.x host 192.168.1.2 eq 3389 (hitcnt=3) 0x02f13f4e
    access-list dmz-access-vlan1; 1 elements; name hash: 0xc3450860
    access-list dmz-access-vlan1 line 1 extended permit ip 128.162.1.0 255.255.255.0 any (hitcnt=0) 0x429fedf1
    access-list dmz-access; 3 elements; name hash: 0xf53f5801
    access-list dmz-access line 1 remark Permit all traffic to DC1
    access-list dmz-access line 2 extended permit ip 128.162.1.0 255.255.255.0 host 192.168.1.2 (hitcnt=0) 0xd2dced0a
    access-list dmz-access line 3 remark Permit only DNS traffic to DNS server
    access-list dmz-access line 4 extended permit udp 128.162.1.0 255.255.255.0 host 192.168.1.2 eq domain (hitcnt=0) 0xbb21093e
    access-list dmz-access line 5 remark Permit ICMP to all devices in DC
    access-list dmz-access line 6 extended permit icmp 128.162.1.0 255.255.255.0 192.168.1.0 255.255.255.0 (hitcnt=0) 0x71269ef7
    CISCO-2811#show access-lists
    Standard IP access list 1
        10 permit any (1581021 matches)
    CISCO-2811#show translate
    CISCO-2811#show route
    CISCO-2811#show route-map
    CISCO-2811#show host
    CISCO-2811#show hosts
    Default domain is maladomini.int
    Name/address lookup uses domain service
    Name servers are 192.168.1.2, 199.195.168.4, 205.171.2.65, 205.171.3.65, 8.8.8.8
    Codes: UN - unknown, EX - expired, OK - OK, ?? - revalidate
           temp - temporary, perm - permanent
           NA - Not Applicable None - Not defined
    Host                      Port  Flags      Age Type   Address(es)
    api.mixpanel.com          None  (temp, OK)  2   IP    198.23.64.21
                                                          198.23.64.22
                                                          198.23.64.18
                                                          198.23.64.19
                                                          198.23.64.20
    ASA5510:
    ASA5510# sh run all
    : Saved
    ASA Version 9.1(4)
    command-alias exec h help
    command-alias exec lo logout
    command-alias exec p ping
    command-alias exec s show
    terminal width 80
    hostname ASA5510
    domain-name maladomini.int
    enable password x encrypted
    no fips enable
    xlate per-session deny tcp any4 any4
    xlate per-session deny tcp any4 any6
    xlate per-session deny tcp any6 any4
    xlate per-session deny tcp any6 any6
    xlate per-session deny udp any4 any4 eq domain
    xlate per-session deny udp any4 any6 eq domain
    xlate per-session deny udp any6 any4 eq domain
    xlate per-session deny udp any6 any6 eq domain
    xlate per-session permit tcp any4 any4
    xlate per-session permit tcp any4 any6
    xlate per-session permit tcp any6 any4
    xlate per-session permit tcp any6 any6
    xlate per-session permit udp any4 any4 eq domain
    xlate per-session permit udp any4 any6 eq domain
    xlate per-session permit udp any6 any4 eq domain
    xlate per-session permit udp any6 any6 eq domain
    passwd x encrypted
    names
    dns-guard
    lacp system-priority 32768
    interface Ethernet0/0
    description LAN Interface
    speed auto
    duplex auto
    no  flowcontrol send on
    nameif Inside
    security-level 100
    ip address 10.10.1.1 255.255.255.252
    delay 10
    interface Ethernet0/1
    description WAN Interface
    speed auto
    duplex auto
    no  flowcontrol send on
    nameif Outside
    security-level 0
    ip address 199.195.168.xxx 255.255.255.240
    delay 10
    interface Ethernet0/2
    description DMZ
    speed auto
    duplex auto
    no  flowcontrol send on
    nameif DMZ
    security-level 100
    ip address 10.10.0.1 255.255.255.252
    delay 10
    interface Ethernet0/3
    description VOIP
    speed auto
    duplex auto
    no  flowcontrol send on
    nameif VOIP
    security-level 100
    ip address 10.10.2.1 255.255.255.252
    delay 10
    interface Management0/0
    speed auto
    duplex auto
    management-only
    shutdown
    nameif management
    security-level 0
    no ip address
    delay 10
    regex _default_gator "Gator"
    regex _default_firethru-tunnel_2 "[/\\]cgi[-]bin[/\\]proxy"
    regex _default_shoutcast-tunneling-protocol "1"
    regex _default_http-tunnel "[/\\]HT_PortLog.aspx"
    regex _default_x-kazaa-network "[\r\n\t ]+[xX]-[kK][aA][zZ][aA][aA]-[nN][eE][tT][wW][oO][rR][kK]"
    regex _default_msn-messenger "[Aa][Pp][Pp][Ll][Ii][Cc][Aa][Tt][Ii][Oo][Nn][/\\][Xx][-][Mm][Ss][Nn][-][Mm][Ee][Ss][Ss][Ee][Nn][Gg][Ee][Rr]"
    regex _default_GoToMyPC-tunnel_2 "[/\\]erc[/\\]Poll"
    regex _default_gnu-http-tunnel_uri "[/\\]index[.]html"
    regex _default_aim-messenger "[Hh][Tt][Tt][Pp][.][Pp][Rr][Oo][Xx][Yy][.][Ii][Cc][Qq][.][Cc][Oo][Mm]"
    regex _default_gnu-http-tunnel_arg "crap"
    regex _default_icy-metadata "[\r\n\t ]+[iI][cC][yY]-[mM][eE][tT][aA][dD][aA][tT][aA]"
    regex _default_GoToMyPC-tunnel "machinekey"
    regex _default_windows-media-player-tunnel "NSPlayer"
    regex _default_yahoo-messenger "YMSG"
    regex _default_httport-tunnel "photo[.]exectech[-]va[.]com"
    regex _default_firethru-tunnel_1 "firethru[.]com"
    checkheaps check-interval 60
    checkheaps validate-checksum 60
    boot system disk0:/asa914-k8.bin
    ftp mode passive
    clock timezone UTC 0
    dns domain-lookup Outside
    dns server-group DefaultDNS
    name-server 199.195.168.4
    name-server 205.171.2.65
    name-server 205.171.3.65
    domain-name maladomini.int
    same-security-traffic permit inter-interface
    object service ah pre-defined
    service ah
    description This is a pre-defined object
    object service eigrp pre-defined
    service eigrp
    description This is a pre-defined object
    object service esp pre-defined
    service esp
    description This is a pre-defined object
    object service gre pre-defined
    service gre
    description This is a pre-defined object
    object service icmp pre-defined
    service icmp
    description This is a pre-defined object
    object service icmp6 pre-defined
    service icmp6
    description This is a pre-defined object
    object service igmp pre-defined
    service igmp
    description This is a pre-defined object
    object service igrp pre-defined
    service igrp
    description This is a pre-defined object
    object service ip pre-defined
    service ip
    description This is a pre-defined object
    object service ipinip pre-defined
    service ipinip
    description This is a pre-defined object
    object service ipsec pre-defined
    service esp
    description This is a pre-defined object
    object service nos pre-defined
    service nos
    description This is a pre-defined object
    object service ospf pre-defined
    service ospf
    description This is a pre-defined object
    object service pcp pre-defined
    service pcp
    description This is a pre-defined object
    object service pim pre-defined
    service pim
    description This is a pre-defined object
    object service pptp pre-defined
    service gre
    description This is a pre-defined object
    object service snp pre-defined
    service snp
    description This is a pre-defined object
    object service tcp pre-defined
    service tcp
    description This is a pre-defined object
    object service udp pre-defined
    service udp
    description This is a pre-defined object
    object service tcp-aol pre-defined
    service tcp destination eq aol
    description This is a pre-defined object
    object service tcp-bgp pre-defined
    service tcp destination eq bgp
    description This is a pre-defined object
    object service tcp-chargen pre-defined
    service tcp destination eq chargen
    description This is a pre-defined object
    object service tcp-cifs pre-defined
    service tcp destination eq cifs
    description This is a pre-defined object
    object service tcp-citrix-ica pre-defined
    service tcp destination eq citrix-ica
    description This is a pre-defined object
    object service tcp-ctiqbe pre-defined
    service tcp destination eq ctiqbe
    description This is a pre-defined object
    object service tcp-daytime pre-defined
    service tcp destination eq daytime
    description This is a pre-defined object
    object service tcp-discard pre-defined
    service tcp destination eq discard
    description This is a pre-defined object
    object service tcp-domain pre-defined
    service tcp destination eq domain
    description This is a pre-defined object
    object service tcp-echo pre-defined
    service tcp destination eq echo
    description This is a pre-defined object
    object service tcp-exec pre-defined
    service tcp destination eq exec
    description This is a pre-defined object
    object service tcp-finger pre-defined
    service tcp destination eq finger
    description This is a pre-defined object
    object service tcp-ftp pre-defined
    service tcp destination eq ftp
    description This is a pre-defined object
    object service tcp-ftp-data pre-defined
    service tcp destination eq ftp-data
    description This is a pre-defined object
    object service tcp-gopher pre-defined
    service tcp destination eq gopher
    description This is a pre-defined object
    object service tcp-ident pre-defined
    service tcp destination eq ident
    description This is a pre-defined object
    object service tcp-imap4 pre-defined
    service tcp destination eq imap4
    description This is a pre-defined object
    object service tcp-irc pre-defined
    service tcp destination eq irc
    description This is a pre-defined object
    object service tcp-hostname pre-defined
    service tcp destination eq hostname
    description This is a pre-defined object
    object service tcp-kerberos pre-defined
    service tcp destination eq kerberos
    description This is a pre-defined object
    object service tcp-klogin pre-defined
    service tcp destination eq klogin
    description This is a pre-defined object
    object service tcp-kshell pre-defined
    service tcp destination eq kshell
    description This is a pre-defined object
    object service tcp-ldap pre-defined
    service tcp destination eq ldap
    description This is a pre-defined object
    object service tcp-ldaps pre-defined
    service tcp destination eq ldaps
    description This is a pre-defined object
    object service tcp-login pre-defined
    service tcp destination eq login
    description This is a pre-defined object
    object service tcp-lotusnotes pre-defined
    service tcp destination eq lotusnotes
    description This is a pre-defined object
    object service tcp-nfs pre-defined
    service tcp destination eq nfs
    description This is a pre-defined object
    object service tcp-netbios-ssn pre-defined
    service tcp destination eq netbios-ssn
    description This is a pre-defined object
    object service tcp-whois pre-defined
    service tcp destination eq whois
    description This is a pre-defined object
    object service tcp-nntp pre-defined
    service tcp destination eq nntp
    description This is a pre-defined object
    object service tcp-pcanywhere-data pre-defined
    service tcp destination eq pcanywhere-data
    description This is a pre-defined object
    object service tcp-pim-auto-rp pre-defined
    service tcp destination eq pim-auto-rp
    description This is a pre-defined object
    object service tcp-pop2 pre-defined
    service tcp destination eq pop2
    description This is a pre-defined object
    object service tcp-pop3 pre-defined
    service tcp destination eq pop3
    description This is a pre-defined object
    object service tcp-pptp pre-defined
    service tcp destination eq pptp
    description This is a pre-defined object
    object service tcp-lpd pre-defined
    service tcp destination eq lpd
    description This is a pre-defined object
    object service tcp-rsh pre-defined
    service tcp destination eq rsh
    description This is a pre-defined object
    object service tcp-rtsp pre-defined
    service tcp destination eq rtsp
    description This is a pre-defined object
    object service tcp-sip pre-defined
    service tcp destination eq sip
    description This is a pre-defined object
    object service tcp-smtp pre-defined
    service tcp destination eq smtp
    description This is a pre-defined object
    object service tcp-ssh pre-defined
    service tcp destination eq ssh
    description This is a pre-defined object
    object service tcp-sunrpc pre-defined
    service tcp destination eq sunrpc
    description This is a pre-defined object
    object service tcp-tacacs pre-defined
    service tcp destination eq tacacs
    description This is a pre-defined object
    object service tcp-talk pre-defined
    service tcp destination eq talk
    description This is a pre-defined object
    object service tcp-telnet pre-defined
    service tcp destination eq telnet
    description This is a pre-defined object
    object service tcp-uucp pre-defined
    service tcp destination eq uucp
    description This is a pre-defined object
    object service tcp-www pre-defined
    service tcp destination eq www
    description This is a pre-defined object
    object service tcp-http pre-defined
    service tcp destination eq www
    description This is a pre-defined object
    object service tcp-https pre-defined
    service tcp destination eq https
    description This is a pre-defined object
    object service tcp-cmd pre-defined
    service tcp destination eq rsh
    description This is a pre-defined object
    object service tcp-sqlnet pre-defined
    service tcp destination eq sqlnet
    description This is a pre-defined object
    object service tcp-h323 pre-defined
    service tcp destination eq h323
    description This is a pre-defined object
    object service tcp-udp-cifs pre-defined
    service tcp-udp destination eq cifs
    description This is a pre-defined object
    object service tcp-udp-discard pre-defined
    service tcp-udp destination eq discard
    description This is a pre-defined object
    object service tcp-udp-domain pre-defined
    service tcp-udp destination eq domain
    description This is a pre-defined object
    object service tcp-udp-echo pre-defined
    service tcp-udp destination eq echo
    description This is a pre-defined object
    object service tcp-udp-kerberos pre-defined
    service tcp-udp destination eq kerberos
    description This is a pre-defined object
    object service tcp-udp-nfs pre-defined
    service tcp-udp destination eq nfs
    description This is a pre-defined object
    object service tcp-udp-pim-auto-rp pre-defined
    service tcp-udp destination eq pim-auto-rp
    description This is a pre-defined object
    object service tcp-udp-sip pre-defined
    service tcp-udp destination eq sip
    description This is a pre-defined object
    object service tcp-udp-sunrpc pre-defined
    service tcp-udp destination eq sunrpc
    description This is a pre-defined object
    object service tcp-udp-tacacs pre-defined
    service tcp-udp destination eq tacacs
    description This is a pre-defined object
    object service tcp-udp-www pre-defined
    service tcp-udp destination eq www
    description This is a pre-defined object
    object service tcp-udp-http pre-defined
    service tcp-udp destination eq www
    description This is a pre-defined object
    object service tcp-udp-talk pre-defined
    service tcp-udp destination eq talk
    description This is a pre-defined object
    object service udp-biff pre-defined
    service udp destination eq biff
    description This is a pre-defined object
    object service udp-bootpc pre-defined
    service udp destination eq bootpc
    description This is a pre-defined object
    object service udp-bootps pre-defined
    service udp destination eq bootps
    description This is a pre-defined object
    object service udp-cifs pre-defined
    service udp destination eq cifs
    description This is a pre-defined object
    object service udp-discard pre-defined
    service udp destination eq discard
    description This is a pre-defined object
    object service udp-domain pre-defined
    service udp destination eq domain
    description This is a pre-defined object
    object service udp-dnsix pre-defined
    service udp destination eq dnsix
    description This is a pre-defined object
    object service udp-echo pre-defined
    service udp destination eq echo
    description This is a pre-defined object
    object service udp-www pre-defined
    service udp destination eq www
    description This is a pre-defined object
    object service udp-http pre-defined
    service udp destination eq www
    description This is a pre-defined object
    object service udp-nameserver pre-defined
    service udp destination eq nameserver
    description This is a pre-defined object
    object service udp-kerberos pre-defined
    service udp destination eq kerberos
    description This is a pre-defined object
    object service udp-mobile-ip pre-defined
    service udp destination eq mobile-ip
    description This is a pre-defined object
    object service udp-nfs pre-defined
    service udp destination eq nfs
    description This is a pre-defined object
    object service udp-netbios-ns pre-defined
    service udp destination eq netbios-ns
    description This is a pre-defined object
    object service udp-netbios-dgm pre-defined
    service udp destination eq netbios-dgm
    description This is a pre-defined object
    object service udp-ntp pre-defined
    service udp destination eq ntp
    description This is a pre-defined object
    object service udp-pcanywhere-status pre-defined
    service udp destination eq pcanywhere-status
    description This is a pre-defined object
    object service udp-pim-auto-rp pre-defined
    service udp destination eq pim-auto-rp
    description This is a pre-defined object
    object service udp-radius pre-defined
    service udp destination eq radius
    description This is a pre-defined object
    object service udp-radius-acct pre-defined
    service udp destination eq radius-acct
    description This is a pre-defined object
    object service udp-rip pre-defined
    service udp destination eq rip
    description This is a pre-defined object
    object service udp-secureid-udp pre-defined
    service udp destination eq secureid-udp
    description This is a pre-defined object
    object service udp-sip pre-defined
    service udp destination eq sip
    description This is a pre-defined object
    object service udp-snmp pre-defined
    service udp destination eq snmp
    description This is a pre-defined object
    object service udp-snmptrap pre-defined
    service udp destination eq snmptrap
    description This is a pre-defined object
    object service udp-sunrpc pre-defined
    service udp destination eq sunrpc
    description This is a pre-defined object
    object service udp-syslog pre-defined
    service udp destination eq syslog
    description This is a pre-defined object
    object service udp-tacacs pre-defined
    service udp destination eq tacacs
    description This is a pre-defined object
    object service udp-talk pre-defined
    service udp destination eq talk
    description This is a pre-defined object
    object service udp-tftp pre-defined
    service udp destination eq tftp
    description This is a pre-defined object
    object service udp-time pre-defined
    service udp destination eq time
    description This is a pre-defined object
    object service udp-who pre-defined
    service udp destination eq who
    description This is a pre-defined object
    object service udp-xdmcp pre-defined
    service udp destination eq xdmcp
    description This is a pre-defined object
    object service udp-isakmp pre-defined
    service udp destination eq isakmp
    description This is a pre-defined object
    object service icmp6-unreachable pre-defined
    service icmp6 unreachable
    description This is a pre-defined object
    object service icmp6-packet-too-big pre-defined
    service icmp6 packet-too-big
    description This is a pre-defined object
    object service icmp6-time-exceeded pre-defined
    service icmp6 time-exceeded
    description This is a pre-defined object
    object service icmp6-parameter-problem pre-defined
    service icmp6 parameter-problem
    description This is a pre-defined object
    object service icmp6-echo pre-defined
    service icmp6 echo
    description This is a pre-defined object
    object service icmp6-echo-reply pre-defined
    service icmp6 echo-reply
    description This is a pre-defined object
    object service icmp6-membership-query pre-defined
    service icmp6 membership-query
    description This is a pre-defined object
    object service icmp6-membership-report pre-defined
    service icmp6 membership-report
    description This is a pre-defined object
    object service icmp6-membership-reduction pre-defined
    service icmp6 membership-reduction
    description This is a pre-defined object
    object service icmp6-router-renumbering pre-defined
    service icmp6 router-renumbering
    description This is a pre-defined object
    object service icmp6-router-solicitation pre-defined
    service icmp6 router-solicitation
    description This is a pre-defined object
    object service icmp6-router-advertisement pre-defined
    service icmp6 router-advertisement
    description This is a pre-defined object
    object service icmp6-neighbor-solicitation pre-defined
    service icmp6 neighbor-solicitation
    description This is a pre-defined object
    object service icmp6-neighbor-advertisement pre-defined
    service icmp6 neighbor-advertisement
    description This is a pre-defined object
    object service icmp6-neighbor-redirect pre-defined
    service icmp6 neighbor-redirect
    description This is a pre-defined object
    object service icmp-echo pre-defined
    service icmp echo
    description This is a pre-defined object
    object service icmp-echo-reply pre-defined
    service icmp echo-reply
    description This is a pre-defined object
    object service icmp-unreachable pre-defined
    service icmp unreachable
    description This is a pre-defined object
    object service icmp-source-quench pre-defined
    service icmp source-quench
    description This is a pre-defined object
    object service icmp-redirect pre-defined
    service icmp redirect
    description This is a pre-defined object
    object service icmp-alternate-address pre-defined
    service icmp alternate-address
    description This is a pre-defined object
    object service icmp-router-advertisement pre-defined
    service icmp router-advertisement
    description This is a pre-defined object
    object service icmp-router-solicitation pre-defined
    service icmp router-solicitation
    description This is a pre-defined object
    object service icmp-time-exceeded pre-defined
    service icmp time-exceeded
    description This is a pre-defined object
    object service icmp-parameter-problem pre-defined
    service icmp parameter-problem
    description This is a pre-defined object
    object service icmp-timestamp-request pre-defined
    service icmp timestamp-request
    description This is a pre-defined object
    object service icmp-timestamp-reply pre-defined
    service icmp timestamp-reply
    description This is a pre-defined object
    object service icmp-information-request pre-defined
    service icmp information-request
    description This is a pre-defined object
    object service icmp-information-reply pre-defined
    service icmp information-reply
    description This is a pre-defined object
    object service icmp-mask-request pre-defined
    service icmp mask-request
    description This is a pre-defined object
    object service icmp-mask-reply pre-defined
    service icmp mask-reply
    description This is a pre-defined object
    object service icmp-traceroute pre-defined
    service icmp traceroute
    description This is a pre-defined object
    object service icmp-conversion-error pre-defined
    service icmp conversion-error
    description This is a pre-defined object
    object service icmp-mobile-redirect pre-defined
    service icmp mobile-redirect
    description This is a pre-defined object
    object network ROUTER-2811
    host 10.10.1.2
    object network ROUTER-2821
    host 10.10.0.2
    object network WEBCAM-01
    host 192.168.1.5
    object network DNS-SERVER
    host 192.168.1.2
    object network ROUTER-3745
    host 10.10.2.2
    object network RDP-DC1
    host 192.168.1.2
    object-group network PAT-SOURCE
    network-object 10.10.1.0 255.255.255.252
    network-object 10.10.0.0 255.255.255.252
    network-object 10.10.2.0 255.255.255.252
    network-object 192.168.0.0 255.255.255.0
    network-object 172.16.10.0 255.255.255.0
    network-object 172.16.20.0 255.255.255.0
    network-object 128.162.1.0 255.255.255.0
    network-object 128.162.10.0 255.255.255.0
    network-object 128.162.20.0 255.255.255.0
    object-group network DM_INLINE_NETWORK_2
    network-object host 98.22.121.x
    object-group network Outside_access_in
    object-group protocol DM_INLINE_PROTOCOL_1
    protocol-object gre
    access-list USERS standard permit 10.10.1.0 255.255.255.0
    access-list Outside_access_in extended permit tcp host 98.22.121.x object ROUTER-2811 eq ssh
    access-list Outside_access_in extended permit tcp host 98.22.121.x object ROUTER-2821 eq ssh
    access-list Outside_access_in extended permit tcp host 98.22.121.x interface Outside eq https
    access-list Outside_access_in extended permit tcp host 98.22.121.x object WEBCAM-01 eq www
    access-list Outside_access_in extended permit tcp host 98.22.121.x object RDP-DC1 eq 3389
    access-list dmz-access-vlan1 extended permit ip 128.162.1.0 255.255.255.0 any
    access-list dmz-access remark Permit all traffic to DC1
    access-list dmz-access extended permit ip 128.162.1.0 255.255.255.0 host 192.168.1.2
    access-list dmz-access remark Permit only DNS traffic to DNS server
    access-list dmz-access extended permit udp 128.162.1.0 255.255.255.0 host 192.168.1.2 eq domain
    access-list dmz-access remark Permit ICMP to all devices in DC
    access-list dmz-access extended permit icmp 128.162.1.0 255.255.255.0 192.168.1.0 255.255.255.0
    pager lines 24
    logging enable
    logging buffer-size 4096
    logging asdm-buffer-size 100
    logging asdm informational
    logging flash-minimum-free 3076
    logging flash-maximum-allocation 1024
    logging rate-limit 1 10 message 747001
    logging rate-limit 1 1 message 402116
    logging rate-limit 1 10 message 620002
    logging rate-limit 1 10 message 717015
    logging rate-limit 1 10 message 717018
    logging rate-limit 1 10 message 201013
    logging rate-limit 1 10 message 201012
    logging rate-limit 1 1 message 313009
    logging rate-limit 100 1 message 750003
    logging rate-limit 100 1 message 750002
    logging rate-limit 100 1 message 750004
    logging rate-limit 1 10 message 419003
    logging rate-limit 1 10 message 405002
    logging rate-limit 1 10 message 405003
    logging rate-limit 1 10 message 421007
    logging rate-limit 1 10 message 405001
    logging rate-limit 1 10 message 421001
    logging rate-limit 1 10 message 421002
    logging rate-limit 1 10 message 337004
    logging rate-limit 1 10 message 337005
    logging rate-limit 1 10 message 337001
    logging rate-limit 1 10 message 337002
    logging rate-limit 1 60 message 199020
    logging rate-limit 1 10 message 337003
    logging rate-limit 2 5 message 199011
    logging rate-limit 1 10 message 199010
    logging rate-limit 1 10 message 337009
    logging rate-limit 2 5 message 199012
    logging rate-limit 1 10 message 710002
    logging rate-limit 1 10 message 209003
    logging rate-limit 1 10 message 209004
    logging rate-limit 1 10 message 209005
    logging rate-limit 1 10 message 431002
    logging rate-limit 1 10 message 431001
    logging rate-limit 1 1 message 447001
    logging rate-limit 1 10 message 110003
    logging rate-limit 1 10 message 110002
    logging rate-limit 1 10 message 429007
    logging rate-limit 1 10 message 216004
    logging rate-limit 1 10 message 450001
    flow-export template timeout-rate 30
    flow-export active refresh-interval 1
    mtu Inside 1500
    mtu Outside 1500
    mtu management 1500
    mtu DMZ 1500
    mtu VOIP 1500
    icmp unreachable rate-limit 1 burst-size 1
    icmp deny any Outside
    asdm image disk0:/asdm-715.bin
    no asdm history enable
    arp timeout 14400
    no arp permit-nonconnected
    object network ROUTER-2811
    nat (Inside,Outside) static interface service tcp ssh 222
    object network ROUTER-2821
    nat (DMZ,Outside) static interface service tcp ssh 2222
    object network WEBCAM-01
    nat (Inside,Outside) static interface service tcp www 8080
    object network ROUTER-3745
    nat (VOIP,Outside) static interface service tcp ssh 2223
    object network RDP-DC1
    nat (Inside,Outside) static interface service tcp 3389 3389
    nat (any,Outside) after-auto source dynamic PAT-SOURCE interface
    access-group Outside_access_in in interface Outside
    ipv6 dhcprelay timeout 60
    router rip
    network 10.0.0.0
    version 2
    no auto-summary
    route Outside 0.0.0.0 0.0.0.0 199.195.168.113 1
    route Inside 128.162.1.0 255.255.255.0 10.10.0.2 1
    route Inside 128.162.10.0 255.255.255.0 10.10.0.2 1
    route Inside 128.162.20.0 255.255.255.0 10.10.0.2 1
    route Inside 172.16.10.0 255.255.255.0 10.10.1.2 1
    route Inside 172.16.20.0 255.255.255.0 10.10.1.2 1
    route Inside 192.168.1.0 255.255.255.0 10.10.1.2 1
    timeout xlate 3:00:00
    timeout pat-xlate 0:00:30
    timeout conn 1:00:00 half-closed 0:10:00 udp 0:02:00 icmp 0:00:02
    timeout sunrpc 0:10:00 h323 0:05:00 h225 1:00:00 mgcp 0:05:00 mgcp-pat 0:05:00
    timeout sip 0:30:00 sip_media 0:02:00 sip-invite 0:03:00 sip-disconnect 0:02:00
    timeout sip-provisional-media 0:02:00 uauth 0:05:00 absolute
    timeout tcp-proxy-reassembly 0:01:00
    timeout floating-conn 0:00:00
    dynamic-access-policy-record DfltAccessPolicy
    action continue
    no cts server-group
    no cts sxp enable
    no cts sxp default
    no cts sxp default source-ip
    cts sxp reconciliation period 120
    cts sxp retry period 120
    user-identity enable
    user-identity domain LOCAL
    user-identity default-domain LOCAL
    user-identity action mac-address-mismatch remove-user-ip
    user-identity inactive-user-timer minutes 60
    user-identity poll-import-user-group-timer hours 8
    user-identity ad-agent active-user-database full-download
    user-identity ad-agent hello-timer seconds 30 retry-times 5
    no user-identity user-not-found enable
    aaa authentication ssh console LOCAL
    http server enable 443
    http 0.0.0.0 0.0.0.0 Inside
    http 98.22.121.x 255.255.255.255 Outside
    no snmp-server location
    no snmp-server contact
    snmp-server enable traps snmp authentication linkup linkdown coldstart
    no snmp-server enable traps syslog
    no snmp-server enable traps ipsec start stop
    no snmp-server enable traps entity config-change fru-insert fru-remove fan-failure power-supply power-supply-presence cpu-temperature chassis-temperature power-supply-temperature chassis-fan-failure
    no snmp-server enable traps memory-threshold
    no snmp-server enable traps interface-threshold
    no snmp-server enable traps remote-access session-threshold-exceeded
    no snmp-server enable traps connection-limit-reached
    no snmp-server enable traps cpu threshold rising
    no snmp-server enable traps ikev2 start stop
    no snmp-server enable traps nat packet-discard
    snmp-server enable
    snmp-server listen-port 161
    fragment size 200 Inside
    fragment chain 24 Inside
    fragment timeout 5 Inside
    no fragment reassembly full Inside
    fragment size 200 Outside
    fragment chain 24 Outside
    fragment timeout 5 Outside
    no fragment reassembly full Outside
    fragment size 200 management
    fragment chain 24 management
    fragment timeout 5 management
    no fragment reassembly full management
    fragment size 200 DMZ
    fragment chain 24 DMZ
    fragment timeout 5 DMZ
    no fragment reassembly full DMZ
    fragment size 200 VOIP
    fragment chain 24 VOIP
    fragment timeout 5 VOIP
    no fragment reassembly full VOIP
    no sysopt connection timewait
    sysopt connection tcpmss 1380
    sysopt connection tcpmss minimum 0
    sysopt connection permit-vpn
    sysopt connection reclassify-vpn
    no sysopt connection preserve-vpn-flows
    no sysopt radius ignore-secret
    no sysopt noproxyarp Inside
    no sysopt noproxyarp Outside
    no sysopt noproxyarp management
    no sysopt noproxyarp DMZ
    no sysopt noproxyarp VOIP
    service password-recovery
    no crypto ipsec ikev2 sa-strength-enforcement
    crypto ipsec security-association lifetime seconds 28800
    crypto ipsec security-association lifetime kilobytes 4608000
    crypto ipsec security-association replay window-size 64
    crypto ipsec security-association pmtu-aging infinite
    crypto ipsec fragmentation before-encryption Inside
    crypto ipsec fragmentation before-encryption Outside
    crypto ipsec fragmentation before-encryption management
    crypto ipsec fragmentation before-encryption DMZ
    crypto ipsec fragmentation before-encryption VOIP
    crypto ipsec df-bit copy-df Inside
    crypto ipsec df-bit copy-df Outside
    crypto ipsec df-bit copy-df management
    crypto ipsec df-bit copy-df DMZ
    crypto ipsec df-bit copy-df VOIP
    crypto ca trustpool policy
    revocation-check none
    crl cache-time 60
    crl enforcenextupdate
    crypto isakmp identity auto
    crypto isakmp nat-traversal 20
    crypto ikev2 cookie-challenge 50
    crypto ikev2 limit max-in-negotiation-sa 100
    no crypto ikev2 limit max-sa
    crypto ikev2 redirect during-auth
    crypto ikev1 limit max-in-negotiation-sa 20
    telnet timeout 5
    ssh 0.0.0.0 0.0.0.0 Inside
    ssh 98.22.121.x 255.255.255.255 Outside
    ssh timeout 60
    ssh version 2
    ssh key-exchange group dh-group1-sha1
    console timeout 0
    vpn-addr-assign aaa
    vpn-addr-assign dhcp
    vpn-addr-assign local reuse-delay 0
    ipv6-vpn-addr-assign aaa
    ipv6-vpn-addr-assign local reuse-delay 0
    no vpn-sessiondb max-other-vpn-limit
    no vpn-sessiondb max-anyconnect-premium-or-essentials-limit
    no remote-access threshold
    l2tp tunnel hello 60
    tls-proxy maximum-session 100
    threat-detection rate dos-drop rate-interval 600 average-rate 100 burst-rate 400
    threat-detection rate dos-drop rate-interval 3600 average-rate 80 burst-rate 320
    threat-detection rate bad-packet-drop rate-interval 600 average-rate 100 burst-rate 400
    threat-detection rate bad-packet-drop rate-interval 3600 average-rate 80 burst-rate 320
    threat-detection rate acl-drop rate-interval 600 average-rate 400 burst-rate 800
    threat-detection rate acl-drop rate-interval 3600 average-rate 320 burst-rate 640
    threat-detection rate conn-limit-drop rate-interval 600 average-rate 100 burst-rate 400
    threat-detection rate conn-limit-drop rate-interval 3600 average-rate 80 burst-rate 320
    threat-detection rate icmp-drop rate-interval 600 average-rate 100 burst-rate 400
    threat-detection rate icmp-drop rate-interval 3600 average-rate 80 burst-rate 320
    threat-detection rate scanning-threat rate-interval 600 average-rate 5 burst-rate 10
    threat-detection rate scanning-threat rate-interval 3600 average-rate 4 burst-rate 8
    threat-detection rate syn-attack rate-interval 600 average-rate 100 burst-rate 200
    threat-detection rate syn-attack rate-interval 3600 average-rate 80 burst-rate 160
    threat-detection rate fw-drop rate-interval 600 average-rate 400 burst-rate 1600
    threat-detection rate fw-drop rate-interval 3600 average-rate 320 burst-rate 1280
    threat-detection rate inspect-drop rate-interval 600 average-rate 400 burst-rate 1600
    threat-detection rate inspect-drop rate-interval 3600 average-rate 320 burst-rate 1280
    threat-detection rate interface-drop rate-interval 600 average-rate 2000 burst-rate 8000
    threat-detection rate interface-drop rate-interval 3600 average-rate 1600 burst-rate 6400
    threat-detection basic-threat
    threat-detection statistics access-list
    no threat-detection statistics tcp-intercept
    ntp server 24.56.178.140 source Outside prefer
    ssl server-version any
    ssl client-version any
    ssl encryption rc4-sha1 dhe-aes128-sha1 dhe-aes256-sha1 aes128-sha1 aes256-sha1 3des-sha1
    ssl certificate-authentication fca-timeout 2
    webvpn
    memory-size percent 50
    port 443
    dtls port 443
    character-encoding none
    no http-proxy
    no https-proxy
    default-idle-timeout 1800
    portal-access-rule none
    no csd enable
    no anyconnect enable
    no tunnel-group-list enable
    no tunnel-group-preference group-url
    rewrite order 65535 enable resource-mask *
    no internal-password
    no onscreen-keyboard
    no default-language
    no smart-tunnel notification-icon
    no keepout
    cache
      no disable
      max-object-size 1000
      min-object-size 0
      no cache-static-content enable
      lmfactor 20
      expiry-time 1
    no auto-signon
    no error-recovery disable
    no ssl-server-check
    no mus password
    mus host mus.cisco.com
    no hostscan data-limit
    : # show import webvpn customization
    : Template
    : DfltCustomization
    : # show import webvpn url-list
    : Template
    : # show import webvpn translation-table
    : Translation Tables' Templates:
    :   PortForwarder
    :   banners
    :   customization
    :   url-list
    :   webvpn
    : Translation Tables:
    :   fr                   PortForwarder
    :   fr                   customization
    :   fr                   webvpn
    :   ja                   PortForwarder
    :   ja                   customization
    :   ja                   webvpn
    :   ru                   PortForwarder
    :   ru                   customization
    :   ru                   webvpn
    : # show import webvpn mst-translation
    : No MS translation tables defined
    : # show import webvpn webcontent
    : No custom webcontent is loaded
    : # show import webvpn AnyConnect-customization
    : No OEM resources defined
    : # show import webvpn plug-in
    group-policy DfltGrpPolicy internal
    group-policy DfltGrpPolicy attributes
    banner none
    wins-server none
    dns-server none
    dhcp-network-scope none
    vpn-access-hours none
    vpn-simultaneous-logins 3
    vpn-idle-timeout 30
    vpn-idle-timeout alert-interval 1
    vpn-session-timeout none
    vpn-session-timeout alert-interval 1
    vpn-filter none
    ipv6-vpn-filter none
    vpn-tunnel-protocol ikev1 ikev2 l2tp-ipsec ssl-clientless
    password-storage disable
    ip-comp disable
    re-xauth disable
    group-lock none
    pfs disable
    ipsec-udp disable
    ipsec-udp-port 10000
    split-tunnel-policy tunnelall
    ipv6-split-tunnel-policy tunnelall
    split-tunnel-network-list none
    default-domain none
    split-dns none
    split-tunnel-all-dns disable
    intercept-dhcp 255.255.255.255 disable
    secure-unit-authentication disable
    user-authentication disable
    user-authentication-idle-timeout 30
    ip-phone-bypass disable
    client-bypass-protocol disable
    gateway-fqdn none
    leap-bypass disable
    nem disable
    backup-servers keep-client-config
    msie-proxy server none
    msie-proxy method no-modify
    msie-proxy except-list none
    msie-proxy local-bypass disable
    msie-proxy pac-url none
    msie-proxy lockdown enable
    vlan none
    nac-settings none
    address-pools none
    ipv6-address-pools none
    smartcard-removal-disconnect enable
    scep-forwarding-url none
    client-firewall none
    client-access-rule none
    webvpn
      url-list none
      filter none
      homepage none
      html-content-filter none
      port-forward name Application Access
      port-forward disable
      http-proxy disable
      sso-server none
      anyconnect ssl dtls enable
      anyconnect mtu 1406
      anyconnect firewall-rule client-interface private none
      anyconnect firewall-rule client-interface public none
      anyconnect keep-installer installed
      anyconnect ssl keepalive 20
      anyconnect ssl rekey time none
      anyconnect ssl rekey method none
      anyconnect dpd-interval client 30
      anyconnect dpd-interval gateway 30
      anyconnect ssl compression none
      anyconnect dtls compression none
      anyconnect modules none
      anyconnect profiles none
      anyconnect ask none
      customization none
      keep-alive-ignore 4
      http-comp gzip
      download-max-size 2147483647
      upload-max-size 2147483647
      post-max-size 2147483647
      user-storage none
      storage-objects value cookies,credentials
      storage-key none
      hidden-shares none
      smart-tunnel disable
      activex-relay enable
      unix-auth-uid 65534
      unix-auth-gid 65534
      file-entry enable
      file-browsing enable
      url-entry enable
      deny-message value Login was successful, but because certain criteria have not been met or due to some specific group policy, you do not have permission to use any of the VPN features. Contact your IT administrator for more information
      smart-tunnel auto-signon disable
      anyconnect ssl df-bit-ignore disable
      anyconnect routing-filtering-ignore disable
      smart-tunnel tunnel-policy tunnelall
      always-on-vpn profile-setting
    password-policy minimum-length 3
    password-policy minimum-changes 0
    password-policy minimum-lowercase 0
    password-policy minimum-uppercase 0
    password-policy minimum-numeric 0
    password-policy minimum-special 0
    password-policy lifetime 0
    no password-policy authenticate-enable
    quota management-session 0
    tunnel-group DefaultL2LGroup type ipsec-l2l
    tunnel-group DefaultL2LGroup general-attributes
    no accounting-server-group
    default-group-policy DfltGrpPolicy
    tunnel-group DefaultL2LGroup ipsec-attributes
    no ikev1 pre-shared-key
    peer-id-validate req
    no chain
    no ikev1 trust-point
    isakmp keepalive threshold 10 retry 2
    no ikev2 remote-authentication
    no ikev2 local-authentication
    tunnel-group DefaultRAGroup type remote-access
    tunnel-group DefaultRAGroup general-attributes
    no address-pool
    no ipv6-address-pool
    authentication-server-group LOCAL
    secondary-authentication-server-group none
    no accounting-server-group
    default-group-policy DfltGrpPolicy
    no dhcp-server
    no strip-realm
    no nat-assigned-to-public-ip
    no scep-enrollment enable
    no password-management
    no override-account-disable
    no strip-group
    no authorization-required
    username-from-certificate CN OU
    secondary-username-from-certificate CN OU
    authentication-attr-from-server primary
    authenticated-session-username primary
    tunnel-group DefaultRAGroup webvpn-attributes
    customization DfltCustomization
    authentication aaa
    no override-svc-download
    no radius-reject-message
    no proxy-auth sdi
    no pre-fill-username ssl-client
    no pre-fill-username clientless
    no secondary-pre-fill-username ssl-client
    no secondary-pre-fill-username clientless
    dns-group DefaultDNS
    no without-csd
    tunnel-group DefaultRAGroup ipsec-attributes
    no ikev1 pre-shared-key
    peer-id-validate req
    no chain
    no ikev1 trust-point
    no ikev1 radius-sdi-xauth
    isakmp keepalive threshold 300 retry 2
    ikev1 user-authentication xauth
    no ikev2 remote-authentication
    no ikev2 local-authentication
    tunnel-group DefaultRAGroup ppp-attributes
    no authentication pap
    authentication chap
    authentication ms-chap-v1
    no authentication ms-chap-v2
    no authentication eap-proxy
    tunnel-group DefaultWEBVPNGroup type remote-access
    tunnel-group DefaultWEBVPNGroup general-attributes
    no address-pool
    no ipv6-address-pool
    authentication-server-group LOCAL
    secondary-authentication-server-group none
    no accounting-server-group
    default-group-policy DfltGrpPolicy
    no dhcp-server
    no strip-realm
    no nat-assigned-to-public-ip
    no scep-enrollment enable
    no password-management
    no override-account-disable
    no strip-group
    no authorization-required
    username-from-certificate CN OU
    secondary-username-from-certificate CN OU
    authentication-attr-from-server primary
    authenticated-session-username primary
    tunnel-group DefaultWEBVPNGroup webvpn-attributes
    customization DfltCustomization
    authentication aaa
    no override-svc-download
    no radius-reject-message
    no proxy-auth sdi
    no pre-fill-username ssl-client
    no pre-fill-username clientless
    no secondary-pre-fill-username ssl-client
    no secondary-pre-fill-username clientless
    dns-group DefaultDNS
    no without-csd
    tunnel-group DefaultWEBVPNGroup ipsec-attributes
    no ikev1 pre-shared-key
    peer-id-validate req
    no chain
    no ikev1 trust-point
    no ikev1 radius-sdi-xauth
    isakmp keepalive threshold 300 retry 2
    ikev1 user-authentication xauth
    no ikev2 remote-authentication
    no ikev2 local-authentication
    tunnel-group DefaultWEBVPNGroup ppp-attributes
    no authentication pap
    authentication chap
    authentication ms-chap-v1
    no authentication ms-chap-v2
    no authentication eap-proxy
    class-map type inspect http match-all _default_gator
    match request header user-agent regex _default_gator
    class-map type inspect http match-all _default_msn-messenger
    match response header content-type regex _default_msn-messenger
    class-map type inspect http match-all _default_yahoo-messenger
    match request body regex _default_yahoo-messenger
    class-map type inspect http match-all _default_windows-media-player-tunnel
    match request header user-agent regex _default_windows-media-player-tunnel
    class-map type inspect http match-all _default_gnu-http-tunnel
    match request args regex _default_gnu-http-tunnel_arg
    match request uri regex _default_gnu-http-tunnel_uri
    class-map type inspect http match-all _default_firethru-tunnel
    match request header host regex _default_firethru-tunnel_1
    match request uri regex _default_firethru-tunnel_2
    class-map type inspect http match-all _default_aim-messenger
    match request header host regex _default_aim-messenger
    class-map type inspect http match-all _default_http-tunnel
    match request uri regex _default_http-tunnel
    class-map type inspect http match-all _default_kazaa
    match response header regex _default_x-kazaa-network count gt 0
    class-map type inspect http match-all _default_shoutcast-tunneling-protocol
    match request header regex _default_icy-metadata regex _default_shoutcast-tunneling-protocol
    class-map class-default
    match any
    class-map inspection_default
    match default-inspection-traffic
    class-map type inspect http match-all _default_GoToMyPC-tunnel
    match request args regex _default_GoToMyPC-tunnel
    match request uri regex _default_GoToMyPC-tunnel_2
    class-map type inspect http match-all _default_httport-tunnel
    match request header host regex _default_httport-tunnel
    policy-map type inspect rtsp _default_rtsp_map
    description Default RTSP policymap
    parameters
    policy-map type inspect ipv6 _default_ipv6_map
    description Default IPV6 policy-map
    parameters
      verify-header type
      verify-header order
    match header routing-type range 0 255
      drop log
    policy-map type inspect h323 _default_h323_map
    description Default H.323 policymap
    parameters
      no rtp-conformance
    policy-map type inspect dns migrated_dns_map_1
    parameters
      message-length maximum client auto
      message-length maximum 512
      no message-length maximum server
      dns-guard
      protocol-enforcement
      nat-rewrite
      no id-randomization
      no id-mismatch
      no tsig enforced
    policy-map type inspect esmtp _default_esmtp_map
    description Default ESMTP policy-map
    parameters
      mask-banner
      no mail-relay
      no special-character
      no allow-tls
    match cmd line length gt 512
      drop-connection log
    match cmd RCPT count gt 100
      drop-connection log
    match body line length gt 998
      log
    match header line length gt 998
      drop-connection log
    match sender-address length gt 320
      drop-connection log
    match MIME filename length gt 255
      drop-connection log
    match ehlo-reply-parameter others
      mask
    policy-map type inspect ip-options _default_ip_options_map
    description Default IP-OPTIONS policy-map
    parameters
      router-alert action allow
    policy-map global_policy
    class inspection_default
      inspect dns migrated_dns_map_1
      inspect ftp
      inspect h323 h225 _default_h323_map
      inspect h323 ras _default_h323_map
      inspect rsh
      inspect rtsp
      inspect esmtp _default_esmtp_map
      inspect sqlnet
      inspect skinny
      inspect sunrpc
      inspect xdmcp
      inspect sip
      inspect netbios
      inspect tftp
      inspect ip-options _default_ip_options_map
      inspect icmp
      inspect icmp error
      inspect pptp
    class class-default
    policy-map type inspect sip _default_sip_map
    description Default SIP policymap
    parameters
      im
      no ip-address-privacy
      traffic-non-sip
      no rtp-conformance
    policy-map type inspect dns _default_dns_map
    description Default DNS policy-map
    parameters
      no message-length maximum client
      no message-le

    I ran those commands while I had the nat off on the router and here are the results. note, i didn't make any changes to the ASA as you only said to remove the router RIP which I did and reloaded and no change.
    As long as the statements ip nat outside on the Fastethernet 0/0 is off and the ip nat inside is off on the vlan and the overload statement is taken out, I cannot hit the internet.
    CISCO-2811#conf t
    Enter configuration commands, one per line.  End with CNTL/Z.
    CISCO-2811(config)#int
    CISCO-2811(config)#interface f
    CISCO-2811(config)#interface fastEthernet 0/1.3
    CISCO-2811(config-subif)#no ip nat inside
    CISCO-2811(config-subif)#exit
    CISCO-2811(config)#inter
    CISCO-2811(config)#interface f
    CISCO-2811(config)#interface fastEthernet 0/0
    CISCO-2811(config-if)#no ip nat outside
    CISCO-2811(config-if)#exit
    CISCO-2811(config)#$nside source list 1 interface FastEthernet0/0 overload
    Dynamic mapping in use, do you want to delete all entries? [no]: y
    CISCO-2811(config)#exit
    CISCO-2811#sh ip arp
    Protocol  Address          Age (min)  Hardware Addr   Type   Interface
    Internet  10.10.1.1             202   c47d.4f3b.8ea6  ARPA   FastEthernet0/0
    Internet  10.10.1.2               -   0019.55a7.2ae8  ARPA   FastEthernet0/0
    Internet  172.16.10.1             -   0019.55a7.2ae9  ARPA   FastEthernet0/1.1
    Internet  172.16.10.3           238   0011.5c73.28c1  ARPA   FastEthernet0/1.1
    Internet  172.16.10.50           72   cc2d.8c78.065a  ARPA   FastEthernet0/1.1
    Internet  172.16.20.1             -   0019.55a7.2ae9  ARPA   FastEthernet0/1.2
    Internet  172.16.20.3           196   0011.5c73.28c2  ARPA   FastEthernet0/1.2
    Internet  192.168.1.1             -   0019.55a7.2ae9  ARPA   FastEthernet0/1.3
    Internet  192.168.1.2             0   0024.e864.01a8  ARPA   FastEthernet0/1.3
    Internet  192.168.1.3           155   0011.5c73.28c0  ARPA   FastEthernet0/1.3
    Internet  192.168.1.5            61   4802.2a4c.1c74  ARPA   FastEthernet0/1.3
    Internet  192.168.1.20            0   5cf9.dd52.5fa9  ARPA   FastEthernet0/1.3
    Internet  192.168.1.50            0   308c.fb47.f2d9  ARPA   FastEthernet0/1.3
    Internet  192.168.1.51            1   ec35.8677.4057  ARPA   FastEthernet0/1.3
    Internet  192.168.1.52            1   b418.d136.ef72  ARPA   FastEthernet0/1.3
    Internet  192.168.1.53            1   8853.9572.e113  ARPA   FastEthernet0/1.3
    Internet  192.168.1.54           12   0009.b044.9f23  ARPA   FastEthernet0/1.3
    Internet  192.168.1.55            0   f47b.5e9a.7ae5  ARPA   FastEthernet0/1.3
    Internet  192.168.1.149           0   001e.4fc5.a199  ARPA   FastEthernet0/1.3
    Internet  192.168.1.174           0   b8ac.6fff.af83  ARPA   FastEthernet0/1.3
    CISCO-2811#sh ip route
    Codes: L - local, C - connected, S - static, R - RIP, M - mobile, B - BGP
           D - EIGRP, EX - EIGRP external, O - OSPF, IA - OSPF inter area
           N1 - OSPF NSSA external type 1, N2 - OSPF NSSA external type 2
           E1 - OSPF external type 1, E2 - OSPF external type 2
           i - IS-IS, su - IS-IS summary, L1 - IS-IS level-1, L2 - IS-IS level-2
           ia - IS-IS inter area, * - candidate default, U - per-user static route
           o - ODR, P - periodic downloaded static route, H - NHRP, l - LISP
           + - replicated route, % - next hop override
    Gateway of last resort is 10.10.1.1 to network 0.0.0.0
    S*    0.0.0.0/0 [1/0] via 10.10.1.1
          10.0.0.0/8 is variably subnetted, 2 subnets, 2 masks
    C        10.10.1.0/30 is directly connected, FastEthernet0/0
    L        10.10.1.2/32 is directly connected, FastEthernet0/0
          172.16.0.0/16 is variably subnetted, 4 subnets, 2 masks
    C        172.16.10.0/24 is directly connected, FastEthernet0/1.1
    L        172.16.10.1/32 is directly connected, FastEthernet0/1.1
    C        172.16.20.0/24 is directly connected, FastEthernet0/1.2
    L        172.16.20.1/32 is directly connected, FastEthernet0/1.2
          192.168.1.0/24 is variably subnetted, 2 subnets, 2 masks
    C        192.168.1.0/24 is directly connected, FastEthernet0/1.3
    L        192.168.1.1/32 is directly connected, FastEthernet0/1.3
    ASA
    ASA5510# sh arp
            Inside 10.10.1.2 0019.55a7.2ae8 12342
            Outside 199.195.168.113 000c.4243.581a 2
            Outside 199.195.168.116 e05f.b947.116b 2436
            Outside 199.195.168.120 0017.c58a.1123 9192
            DMZ 10.10.0.2 0025.849f.63e0 3192
            VOIP 10.10.2.2 000d.bcdc.fc40 7754
    ASA5510# sh route
    Codes: C - connected, S - static, I - IGRP, R - RIP, M - mobile, B - BGP
           D - EIGRP, EX - EIGRP external, O - OSPF, IA - OSPF inter area
           N1 - OSPF NSSA external type 1, N2 - OSPF NSSA external type 2
           E1 - OSPF external type 1, E2 - OSPF external type 2, E - EGP
           i - IS-IS, L1 - IS-IS level-1, L2 - IS-IS level-2, ia - IS-IS inter area
           * - candidate default, U - per-user static route, o - ODR
           P - periodic downloaded static route
    Gateway of last resort is 199.195.168.113 to network 0.0.0.0
    S    172.16.20.0 255.255.255.0 [1/0] via 10.10.1.2, Inside
    S    172.16.10.0 255.255.255.0 [1/0] via 10.10.1.2, Inside
    S    128.162.1.0 255.255.255.0 [1/0] via 10.10.0.2, DMZ
    S    128.162.10.0 255.255.255.0 [1/0] via 10.10.0.2, DMZ
    S    128.162.20.0 255.255.255.0 [1/0] via 10.10.0.2, DMZ
    C    199.195.168.112 255.255.255.240 is directly connected, Outside
    C    10.10.0.0 255.255.255.252 is directly connected, DMZ
    C    10.10.1.0 255.255.255.252 is directly connected, Inside
    S    192.168.1.0 255.255.255.0 [1/0] via 10.10.1.2, Inside
    S*   0.0.0.0 0.0.0.0 [1/0] via 199.195.168.113, Outside
    ASA5510# show xlate
    35 in use, 784 most used
    Flags: D - DNS, e - extended, I - identity, i - dynamic, r - portmap,
           s - static, T - twice, N - net-to-net
    TCP PAT from DMZ:10.10.0.2 22-22 to Outside:199.195.168.x 2222-2222
        flags sr idle 481:54:14 timeout 0:00:00
    TCP PAT from Inside:10.10.1.2 22-22 to Outside:199.195.168.x 222-222
        flags sr idle 51:06:46 timeout 0:00:00
    TCP PAT from VOIP:10.10.2.2 22-22 to Outside:199.195.168.x 2223-2223
        flags sr idle 687:32:27 timeout 0:00:00
    TCP PAT from Inside:192.168.1.2 3389-3389 to Outside:199.195.168.x 3389-3389
        flags sr idle 457:17:01 timeout 0:00:00
    TCP PAT from Inside:192.168.1.5 80-80 to Outside:199.195.168.x 8080-8080
        flags sr idle 52:18:58 timeout 0:00:00
    NAT from Outside:0.0.0.0/0 to any:0.0.0.0/0
        flags sIT idle 353:10:21 timeout 0:00:00
    UDP PAT from any:10.10.1.2/52581 to Outside:199.195.168.x/52581 flags ri idle 0:00:00 timeout 0:00:30
    UDP PAT from any:10.10.1.2/55389 to Outside:199.195.168.x/55389 flags ri idle 0:00:03 timeout 0:00:30
    UDP PAT from any:10.10.1.2/51936 to Outside:199.195.168.x/51936 flags ri idle 0:00:04 timeout 0:00:30
    UDP PAT from any:10.10.1.2/51345 to Outside:199.195.168.x/51345 flags ri idle 0:00:09 timeout 0:00:30
    UDP PAT from any:10.10.1.2/55985 to Outside:199.195.168.x/55985 flags ri idle 0:00:18 timeout 0:00:30
    UDP PAT from any:10.10.1.2/49368 to Outside:199.195.168.x/49368 flags ri idle 0:00:22 timeout 0:00:30
    UDP PAT from any:10.10.1.2/52441 to Outside:199.195.168.x/52441 flags ri idle 0:00:23 timeout 0:00:30
    TCP PAT from any:10.10.1.2/57908 to Outside:199.195.168.x/57908 flags ri idle 0:08:37 timeout 0:00:30
    TCP PAT from any:10.10.1.2/57907 to Outside:199.195.168.x/57907 flags ri idle 0:08:37 timeout 0:00:30
    TCP PAT from any:10.10.1.2/57906 to Outside:199.195.168.x/57906 flags ri idle 0:08:37 timeout 0:00:30
    TCP PAT from any:10.10.1.2/57896 to Outside:199.195.168.x/57896 flags ri idle 0:09:09 timeout 0:00:30
    TCP PAT from any:10.10.1.2/57879 to Outside:199.195.168.x/57879 flags ri idle 0:10:23 timeout 0:00:30
    TCP PAT from any:10.10.1.2/49441 to Outside:199.195.168.x/49441 flags ri idle 0:20:52 timeout 0:00:30
    TCP PAT from any:10.10.1.2/57868 to Outside:199.195.168.x/57868 flags ri idle 0:25:28 timeout 0:00:30
    TCP PAT from any:10.10.1.2/60519 to Outside:199.195.168.x/60519 flags ri idle 0:44:11 timeout 0:00:30
    TCP PAT from any:10.10.1.2/60491 to Outside:199.195.168.x/60491 flags ri idle 0:44:20 timeout 0:00:30
    TCP PAT from any:10.10.1.2/60484 to Outside:199.195.168.x/60484 flags ri idle 0:44:35 timeout 0:00:30
    TCP PAT from any:10.10.1.2/60480 to Outside:199.195.168.x/60480 flags ri idle 0:44:51 timeout 0:00:30
    TCP PAT from any:10.10.1.2/53851 to Outside:199.195.168.x/53851 flags ri idle 0:54:14 timeout 0:00:30
    TCP PAT from any:10.10.1.2/57812 to Outside:199.195.168.x/57812 flags ri idle 0:58:30 timeout 0:00:30
    TCP PAT from any:10.10.1.2/57810 to Outside:199.195.168.x/57810 flags ri idle 0:58:32 timeout 0:00:30
    TCP PAT from any:10.10.1.2/53847 to Outside:199.195.168.x/53847 flags ri idle 1:00:18 timeout 0:00:30
    TCP PAT from any:10.10.1.2/57808 to Outside:199.195.168.x/57808 flags ri idle 1:07:58 timeout 0:00:30
    TCP PAT from any:10.10.1.2/60406 to Outside:199.195.168.x/60406 flags ri idle 1:42:13 timeout 0:00:30
    TCP PAT from any:10.10.1.2/49259 to Outside:199.195.168.x/49259 flags ri idle 7:39:44 timeout 0:00:30
    TCP PAT from any:10.10.1.2/49191 to Outside:199.195.168.x/49191 flags ri idle 7:42:39 timeout 0:00:30
    TCP PAT from any:10.10.1.2/55951 to Outside:199.195.168.x/55951 flags ri idle 23:11:40 timeout 0:00:30
    TCP PAT from any:10.10.1.2/55944 to Outside:199.195.168.x/55944 flags ri idle 23:15:19 timeout 0:00:30
    TCP PAT from any:10.10.1.2/55942 to Outside:199.195.168.x/55942 flags ri idle 23:15:24 timeout 0:00:30
    ASA5510# sh conn all
    149 in use, 815 most used
    TCP Outside  74.125.193.108:993 Inside  10.10.1.2:57879, idle 0:12:37, bytes 6398, flags UIO
    TCP Outside  174.35.24.74:80 Inside  192.168.1.20:53879, idle 0:00:01, bytes 0, flags saA
    TCP Outside  174.35.24.74:80 Inside  192.168.1.20:53878, idle 0:00:01, bytes 0, flags saA
    TCP Outside  17.149.36.177:5223 Inside  10.10.1.2:60480, idle 0:16:53, bytes 4539, flags UIO
    TCP Outside  98.22.121.19:443 Inside  192.168.1.20:53877, idle 0:00:02, bytes 0, flags saA
    TCP Outside  98.22.121.19:443 Inside  192.168.1.20:53876, idle 0:00:02, bytes 0, flags saA
    TCP Outside  98.22.121.19:443 Inside  192.168.1.20:53875, idle 0:00:05, bytes 0, flags saA
    TCP Outside  98.22.121.19:443 Inside  192.168.1.20:53874, idle 0:00:05, bytes 0, flags saA
    TCP Outside  98.22.121.19:443 Inside  192.168.1.20:53872, idle 0:00:11, bytes 0, flags saA
    TCP Outside  98.22.121.19:443 Inside  192.168.1.20:53871, idle 0:00:11, bytes 0, flags saA
    TCP Outside  98.22.121.19:443 Inside  192.168.1.20:53868, idle 0:00:08, bytes 0, flags saA
    TCP Outside  98.22.121.19:443 Inside  192.168.1.20:53867, idle 0:00:08, bytes 0, flags saA
    TCP Outside  98.22.121.19:443 Inside  192.168.1.20:53860, idle 0:00:17, bytes 0, flags saA
    TCP Outside  98.22.121.19:443 Inside  192.168.1.20:53859, idle 0:00:17, bytes 0, flags saA
    TCP Outside  17.172.233.95:5223 Inside  10.10.1.2:49191, idle 0:18:48, bytes 7384, flags UIO
    TCP Outside  17.178.100.43:443 Inside  10.10.1.2:57810, idle 0:56:21, bytes 5797, flags UFIO
    TCP Outside  23.206.216.93:80 Inside  10.10.1.2:53847, idle 0:54:15, bytes 2683, flags UFIO
    TCP Outside  143.127.93.90:80 Inside  10.10.1.2:49259, idle 0:12:20, bytes 13315, flags UIO
    TCP Outside  74.125.225.53:443 Inside  192.168.1.20:53864, idle 0:00:11, bytes 0, flags saA
    UDP Outside  199.195.168.4:53 Inside  192.168.1.2:49204, idle 0:00:04, bytes 67, flags -
    UDP Outside  199.195.168.4:53 Inside  192.168.1.174:50122, idle 0:00:07, bytes 43, flags -
    UDP Outside  199.195.168.4:53 Inside  192.168.1.2:63275, idle 0:00:08, bytes 54, flags -
    UDP Outside  199.195.168.4:53 Inside  192.168.1.2:63306, idle 0:00:18, bytes 51, flags -
    UDP Outside  199.195.168.4:53 Inside  192.168.1.2:65059, idle 0:00:22, bytes 46, flags -
    UDP Outside  199.195.168.4:53 Inside  192.168.1.2:64681, idle 0:00:30, bytes 54, flags -
    UDP Outside  199.195.168.4:53 Inside  192.168.1.2:64661, idle 0:00:30, bytes 51, flags -
    UDP Outside  199.195.168.4:53 Inside  192.168.1.20:55618, idle 0:00:32, bytes 43, flags -
    UDP Outside  199.195.168.4:53 Inside  192.168.1.2:65056, idle 0:00:33, bytes 48, flags -
    UDP Outside  199.195.168.4:53 Inside  192.168.1.55:59433, idle 0:00:41, bytes 33, flags -
    UDP Outside  199.195.168.4:53 Inside  192.168.1.20:52178, idle 0:00:42, bytes 33, flags -
    UDP Outside  199.195.168.4:53 Inside  192.168.1.174:61414, idle 0:00:43, bytes 34, flags -
    UDP Outside  199.195.168.4:53 Inside  192.168.1.2:65438, idle 0:00:44, bytes 44, flags -
    UDP Outside  199.195.168.4:53 Inside  192.168.1.2:63686, idle 0:00:44, bytes 51, flags -
    UDP Outside  199.195.168.4:53 Inside  192.168.1.2:65416, idle 0:00:45, bytes 45, flags -
    UDP Outside  199.195.168.4:53 Inside  192.168.1.52:53047, idle 0:00:47, bytes 32, flags -
    UDP Outside  199.195.168.4:53 Inside  192.168.1.52:62213, idle 0:00:46, bytes 74, flags -
    UDP Outside  199.195.168.4:53 Inside  192.168.1.52:52347, idle 0:00:46, bytes 92, flags -
    UDP Outside  199.195.168.4:53 Inside  192.168.1.52:58069, idle 0:00:46, bytes 64, flags -
    UDP Outside  199.195.168.4:53 Inside  192.168.1.52:50753, idle 0:00:46, bytes 74, flags -
    UDP Outside  199.195.168.4:53 Inside  192.168.1.2:65381, idle 0:00:50, bytes 50, flags -
    UDP Outside  199.195.168.4:53 Inside  192.168.1.2:65082, idle 0:00:50, bytes 51, flags -
    UDP Outside  199.195.168.4:53 Inside  192.168.1.2:64038, idle 0:00:50, bytes 54, flags -
    UDP Outside  199.195.168.4:53 Inside  192.168.1.2:49309, idle 0:00:51, bytes 43, flags -
    UDP Outside  199.195.168.4:53 Inside  192.168.1.2:64034, idle 0:00:51, bytes 54, flags -
    UDP Outside  199.195.168.4:53 Inside  192.168.1.2:49197, idle 0:00:51, bytes 50, flags -
    UDP Outside  199.195.168.4:53 Inside  192.168.1.2:64728, idle 0:00:51, bytes 49, flags -
    UDP Outside  199.195.168.4:53 Inside  192.168.1.2:64309, idle 0:00:51, bytes 54, flags -
    UDP Outside  199.195.168.4:53 Inside  192.168.1.2:63289, idle 0:00:51, bytes 51, flags -
    UDP Outside  199.195.168.4:53 Inside  192.168.1.2:64174, idle 0:00:52, bytes 54, flags -
    UDP Outside  199.195.168.4:53 Inside  192.168.1.55:39286, idle 0:01:09, bytes 33, flags -
    UDP Outside  199.195.168.4:53 Inside  192.168.1.2:63726, idle 0:01:09, bytes 54, flags -
    UDP Outside  199.195.168.4:53 Inside  192.168.1.2:65482, idle 0:01:12, bytes 51, flags -
    UDP Outside  199.195.168.4:53 Inside  192.168.1.2:65091, idle 0:01:13, bytes 61, flags -
    UDP Outside  199.195.168.4:53 Inside  192.168.1.2:64976, idle 0:01:13, bytes 57, flags -
    UDP Outside  199.195.168.4:53 Inside  192.168.1.2:63749, idle 0:00:51, bytes 103, flags -
    UDP Outside  199.195.168.4:53 Inside  192.168.1.2:64043, idle 0:01:14, bytes 52, flags -
    UDP Outside  199.195.168.4:53 Inside  192.168.1.2:64267, idle 0:01:24, bytes 45, flags -
    UDP Outside  199.195.168.4:53 Inside  192.168.1.2:64467, idle 0:01:26, bytes 45, flags -
    UDP Outside  199.195.168.4:53 Inside  192.168.1.2:65504, idle 0:01:26, bytes 46, flags -
    UDP Outside  199.195.168.4:53 Inside  192.168.1.55:38946, idle 0:01:35, bytes 33, flags -
    UDP Outside  199.195.168.4:53 Inside  192.168.1.2:63701, idle 0:01:38, bytes 51, flags -
    UDP Outside  199.195.168.4:53 Inside  192.168.1.2:63879, idle 0:01:46, bytes 45, flags -
    UDP Outside  199.195.168.4:53 Inside  192.168.1.174:58516, idle 0:01:49, bytes 51, flags -
    UDP Outside  199.195.168.4:53 Inside  192.168.1.2:63227, idle 0:01:51, bytes 62, flags -
    UDP Outside  199.195.168.4:53 Inside  192.168.1.174:65446, idle 0:01:53, bytes 43, flags -
    UDP Outside  199.195.168.4:53 Inside  192.168.1.2:49166, idle 0:01:55, bytes 54, flags -
    UDP Outside  199.195.168.4:53 Inside  192.168.1.55:56680, idle 0:02:01, bytes 33, flags -
    UDP Outside  192.55.83.30:53 Inside  192.168.1.2:65073, idle 0:00:44, bytes 50, flags -
    TCP Outside  74.125.193.109:993 Inside  10.10.1.2:57808, idle 0:39:33, bytes 6392, flags UFIO
    TCP Outside  74.125.225.54:443 Inside  192.168.1.20:53863, idle 0:00:13, bytes 0, flags saA
    TCP Outside  143.127.93.89:80 Inside  10.10.1.2:60519, idle 0:46:30, bytes 346, flags UO
    TCP Outside  74.125.225.32:443 Inside  192.168.1.20:53881, idle 0:00:01, bytes 0, flags saA
    TCP Outside  74.125.225.32:443 Inside  192.168.1.20:53880, idle 0:00:01, bytes 0, flags saA
    UDP Outside  205.171.3.65:53 Inside  192.168.1.52:60627, idle 0:00:39, bytes 78, flags -
    UDP Outside  205.171.3.65:53 Inside  192.168.1.52:52088, idle 0:00:39, bytes 86, flags -
    UDP Outside  205.171.3.65:53 Inside  192.168.1.52:50533, idle 0:00:39, bytes 76, flags -
    UDP Outside  205.171.3.65:53 Inside  192.168.1.52:63347, idle 0:00:39, bytes 80, flags -
    UDP Outside  205.171.3.65:53 Inside  192.168.1.52:62213, idle 0:00:40, bytes 37, flags -
    UDP Outside  205.171.3.65:53 Inside  192.168.1.52:52347, idle 0:00:40, bytes 46, flags -
    UDP Outside  205.171.3.65:53 Inside  192.168.1.52:58069, idle 0:00:40, bytes 32, flags -
    UDP Outside  205.171.3.65:53 Inside  192.168.1.52:50753, idle 0:00:40, bytes 37, flags -
    UDP Outside  205.171.3.65:53 Inside  192.168.1.174:52254, idle 0:01:09, bytes 43, flags -
    UDP Outside  205.171.3.65:53 Inside  192.168.1.174:50791, idle 0:01:25, bytes 35, flags -
    TCP Outside  74.125.225.46:443 Inside  192.168.1.20:53870, idle 0:00:08, bytes 0, flags saA
    TCP Outside  17.173.255.101:443 Inside  10.10.1.2:53851, idle 0:56:33, bytes 58, flags UfIO
    TCP Outside  64.4.23.147:33033 Inside  10.10.1.2:55944, idle 0:44:45, bytes 558164, flags UFIO
    TCP Outside  74.125.225.35:443 Inside  192.168.1.20:53869, idle 0:00:09, bytes 0, flags saA
    UDP Outside  64.4.23.175:33033 Inside  192.168.1.174:26511, idle 0:01:17, bytes 28, flags -
    UDP Outside  192.54.112.30:53 Inside  192.168.1.2:65380, idle 0:00:44, bytes 49, flags -
    TCP Outside  74.125.142.108:993 Inside  10.10.1.2:57908, idle 0:10:47, bytes 7895, flags UIO
    TCP Outside  74.125.142.108:993 Inside  10.10.1.2:57907, idle 0:10:49, bytes 20323, flags UIO
    TCP Outside  74.125.142.108:993 Inside  10.10.1.2:57906, idle 0:10:47, bytes 6539, flags UIO
    TCP Outside  74.125.142.108:993 Inside  10.10.1.2:57868, idle 0:27:44, bytes 6395, flags UIO
    TCP Outside  91.190.218.59:443 Inside  10.10.1.2:55942, idle 0:41:39, bytes 2727, flags UFIO
    TCP Outside  17.172.233.123:5223 Inside  10.10.1.2:49441, idle 0:23:10, bytes 4409, flags UIO
    TCP Outside  74.125.225.41:443 Inside  192.168.1.20:53862, idle 0:00:16, bytes 0, flags saA
    TCP Outside  74.125.225.41:443 Inside  192.168.1.20:53861, idle 0:00:16, bytes 0, flags saA
    TCP Outside  143.127.93.115:80 Inside  10.10.1.2:60406, idle 0:42:59, bytes 970, flags UFIO
    TCP Outside  143.127.93.118:80 Inside  10.10.1.2:60484, idle 0:46:54, bytes 328, flags UO
    TCP Outside  17.172.233.98:5223 Inside  10.10.1.2:57896, idle 0:11:28, bytes 5081, flags UIO
    UDP Outside  111.221.74.16:33033 Inside  192.168.1.174:26511, idle 0:01:18, bytes 31, flags -
    TCP Outside  17.149.36.103:5223 Inside  192.168.1.174:60729, idle 0:00:04, bytes 0, flags saA
    UDP Outside  192.5.6.30:53 Inside  192.168.1.2:65317, idle 0:00:44, bytes 51, flags -
    UDP Outside  192.12.94.30:53 Inside  192.168.1.2:65356, idle 0:00:44, bytes 54, flags -
    TCP Outside  17.149.36.180:5223 Inside  10.10.1.2:55951, idle 0:46:08, bytes 14059, flags UFIO
    UDP Outside  111.221.74.28:33033 Inside  192.168.1.174:26511, idle 0:01:20, bytes 33, flags -
    TCP Outside  63.235.20.160:80 Inside  192.168.1.20:53873, idle 0:00:08, bytes 0, flags saA
    TCP Outside  50.19.127.112:443 Inside  192.168.1.50:60678, idle 0:00:00, bytes 0, flags saA
    TCP Outside  65.55.122.234:80 Inside  192.168.1.174:60728, idle 0:00:14, bytes 0, flags saA
    TCP Outside  65.55.122.234:80 Inside  192.168.1.174:60727, idle 0:00:15, bytes 0, flags saA
    TCP Outside  65.55.122.234:80 Inside  192.168.1.174:60726, idle 0:00:15, bytes 0, flags saA
    TCP Outside  65.55.122.234:443 Inside  192.168.1.174:2492, idle 0:00:16, bytes 0, flags saA
    TCP Outside  65.55.122.234:2492 Inside  192.168.1.174:2492, idle 0:00:16, bytes 0, flags saA
    UDP Outside  157.55.56.170:33033 Inside  192.168.1.174:26511, idle 0:01:21, bytes 37, flags -
    TCP Outside  74.125.230.207:443 Inside  192.168.1.20:53866, idle 0:00:11, bytes 0, flags saA
    TCP Outside  74.125.230.207:443 Inside  192.168.1.20:53865, idle 0:00:11, bytes 0, flags saA
    UDP Outside  111.221.74.18:33033 Inside  192.168.1.174:26511, idle 0:01:17, bytes 29, flags -
    UDP Outside  8.8.8.8:53 Inside  192.168.1.20:55546, idle 0:00:06, bytes 46, flags -
    UDP Outside  8.8.8.8:53 Inside  192.168.1.20:60277, idle 0:00:06, bytes 46, flags -
    UDP Outside  8.8.8.8:53 Inside  192.168.1.20:55618, idle 0:00:34, bytes 43, flags -
    UDP Outside  8.8.8.8:53 Inside  192.168.1.52:60627, idle 0:00:36, bytes 78, flags -
    UDP Outside  8.8.8.8:53 Inside  192.168.1.52:52088, idle 0:00:36, bytes 86, flags -
    UDP Outside  8.8.8.8:53 Inside  192.168.1.52:50533, idle 0:00:36, bytes 76, flags -
    UDP Outside  8.8.8.8:53 Inside  192.168.1.52:63347, idle 0:00:36, bytes 80, flags -
    UDP Outside  8.8.8.8:53 Inside  192.168.1.20:56958, idle 0:01:24, bytes 34, flags -
    UDP Outside  8.8.8.8:53 Inside  192.168.1.20:51360, idle 0:01:26, bytes 34, flags -
    UDP Outside  8.8.8.8:53 Inside  192.168.1.174:50791, idle 0:01:27, bytes 35, flags -
    UDP Outside  8.8.8.8:53 Inside  192.168.1.20:54134, idle 0:01:46, bytes 34, flags -
    UDP Outside  8.8.8.8:53 Inside  192.168.1.174:58516, idle 0:01:50, bytes 51, flags -
    TCP Outside  23.207.7.46:80 Inside  192.168.1.55:59350, idle 0:00:02, bytes 0, flags saA
    TCP Outside  23.207.7.46:80 Inside  192.168.1.55:59349, idle 0:00:16, bytes 0, flags saA
    UDP Outside  205.171.2.65:53 Inside  192.168.1.174:50122, idle 0:00:09, bytes 43, flags -
    UDP Outside  205.171.2.65:53 Inside  192.168.1.55:48088, idle 0:00:42, bytes 33, flags -
    UDP Outside  205.171.2.65:53 Inside  192.168.1.52:62213, idle 0:00:45, bytes 74, flags -
    UDP Outside  205.171.2.65:53 Inside  192.168.1.52:52347, idle 0:00:45, bytes 92, flags -
    UDP Outside  205.171.2.65:53 Inside  192.168.1.52:58069, idle 0:00:45, bytes 64, flags -
    UDP Outside  205.171.2.65:53 Inside  192.168.1.52:50753, idle 0:00:45, bytes 74, flags -
    UDP Outside  205.171.2.65:53 Inside  192.168.1.174:61414, idle 0:00:47, bytes 34, flags -
    UDP Outside  205.171.2.65:53 Inside  192.168.1.55:54481, idle 0:01:08, bytes 33, flags -
    UDP Outside  205.171.2.65:53 Inside  192.168.1.174:52254, idle 0:01:09, bytes 43, flags -
    UDP Outside  205.171.2.65:53 Inside  192.168.1.55:40285, idle 0:01:34, bytes 33, flags -
    UDP Outside  205.171.2.65:53 Inside  192.168.1.174:65446, idle 0:01:55, bytes 43, flags -
    UDP Outside  205.171.2.65:53 Inside  192.168.1.55:46155, idle 0:02:00, bytes 33, flags -
    UDP Outside  66.104.81.70:5070 Inside  192.168.1.174:57609, idle 0:00:11, bytes 46, flags -
    UDP Outside  64.4.23.156:33033 Inside  192.168.1.174:26511, idle 0:01:14, bytes 38, flags -
    TCP Outside  65.54.167.15:12350 Inside  10.10.1.2:60491, idle 0:11:02, bytes 1405, flags UIO
    TCP Outside  17.172.192.35:443 Inside  10.10.1.2:57812, idle 0:56:11, bytes 6116, flags UFIO
    UDP Outside  157.55.56.176:33033 Inside  192.168.1.174:26511, idle 0:01:16, bytes 32, flags -
    TCP Inside  192.168.1.20:53667 NP Identity Ifc  10.10.1.1:22, idle 0:00:00, bytes 37555, flags UOB
    TCP Inside  10.10.1.2:53431 NP Identity Ifc  10.10.1.1:22, idle 0:09:03, bytes 20739, flags UOB
    Ran on the ASA while overload statements were down on the router:
    ASA5510#   packet-tracer input Inside tcp 192.168.1.100 12345 8.8.8.8 80
    Phase: 1
    Type: ROUTE-LOOKUP
    Subtype: input
    Result: ALLOW
    Config:
    Additional Information:
    in   0.0.0.0         0.0.0.0         Outside
    Phase: 2
    Type: NAT
    Subtype: per-session
    Result: ALLOW
    Config:
    Additional Information:
    Phase: 3
    Type: IP-OPTIONS
    Subtype:
    Result: ALLOW
    Config:
    Additional Information:
    Phase: 4
    Type: NAT
    Subtype: per-session
    Result: ALLOW
    Config:
    Additional Information:
    Phase: 5
    Type: IP-OPTIONS
    Subtype:
    Result: ALLOW
    Config:
    Additional Information:
    Phase: 6
    Type: FLOW-CREATION
    Subtype:
    Result: ALLOW
    Config:
    Additional Information:
    New flow created with id 1988699, packet dispatched to next module
    Result:
    input-interface: Inside
    input-status: up
    input-line-status: up
    output-interface: Outside
    output-status: up
    output-line-status: up
    Action: allow
    Had to put these back in to get to the internet:
    CISCO-2811#conf t
    Enter configuration commands, one per line.  End with CNTL/Z.
    CISCO-2811(config)#inter
    CISCO-2811(config)#interface f
    CISCO-2811(config)#interface fastEthernet 0/0
    CISCO-2811(config-if)#ip nat
    CISCO-2811(config-if)#ip nat Outside
    CISCO-2811(config-if)#exit
    CISCO-2811(config)#in
    CISCO-2811(config)#interface f
    CISCO-2811(config)#interface fastEthernet 0/1.3
    CISCO-2811(config-subif)#ip nat inside
    CISCO-2811(config-subif)#exit
    CISCO-2811(config)#$de source list 1 interface FastEthernet0/0 overload
    CISCO-2811(config)#
    Screenshot of ASDM:

  • Cisco 877 router - Cisco IP phone won't register with SIP provider

    Hi all,
    I'm having a problem with a Cisco SPA504G phone not registering with the SIP carrier over the Internet. We've recently rolled out a Cisco 877 router onto a new NBN business connection and can't get the pre-configured IP phone to register.
    When we tested the phone with the NBN-provided Netgear router, it worked fine, as it did with the previous Cisco 1841 router we were using on a different link.
    The way it's setup is using VLANs to define the internal subnets, which are then assigned to the physical interfaces (since the 887 doesn't allow IP assignments to the interfaces directly).
    VLAN 100 is the internal network and has a SBS2011 server – assigned to F0 – IP range is 192.168.1.0
    VLAN 200 is the guest network and has Internet access only – assigned to F1 – IP range is 10.1.1.0
    VLAN 500 is the WAN network and connects to the NBN upstream box – assigned to F3 – external IP address assigned by DHCP
    I've been playing around with access lists, nat rules, basically everything in my limited Cisco knowledge to try and figure this out, but to no avail. I have even configured what I believe is unrestricted access to IP, UDP and TCP outbound and inbound to all VLANs and still can't get it to register.
    Tried isolating the issue by creating a new VLAN and assigning it to the spare interface and basically allowing everything in and out, but still no luck.
    The problem has to be something on the router – probably some small line of config I haven’t removed or added.
    I am going to pull my hair out soon, so would really appreciate some assistance from the Cisco gurus out there.
    My client has just purchased about 10 of these handsets from their provider so I need to fix this ASAP. The guy who provided them wasn't very helpful, and basically said I'm on my own once we tested using the NBN-provided Netgear router.
    Happy to post my config as well.
    Please help!!!!

    Current configuration : 4912 bytes
    version 15.1
    no service pad
    service timestamps debug datetime msec
    service timestamps log datetime msec
    no service password-encryption
    hostname Router1
    boot-start-marker
    boot-end-marker
    no aaa new-model
    memory-size iomem 10
    crypto pki token default removal timeout 0
    no ip source-route
    ip dhcp excluded-address 10.1.1.1
    ip dhcp pool GUEST
     network 10.1.1.0 255.255.255.0
     dns-server 10.1.1.1 203.50.2.71 139.130.4.4
     default-router 10.1.1.1
    ip cef
    no ip domain lookup
    ip domain name network.local
    ip name-server 192.168.1.123
    ip name-server 203.23.53.12
    ip name-server 197.12.32.86
    ip name-server 8.8.8.8
    no ipv6 cef
    license udi pid CISCO887VA-K9 sn FGL171220XY
    username admin privilege 15 secret 5 $1$aNsm$N1BCQYkoi8gnURyvloYEX/
    controller VDSL 0
    interface Ethernet0
     no ip address
     shutdown
    interface ATM0
     no ip address
     no atm ilmi-keepalive
     bridge-group 10
     pvc 8/35
    interface FastEthernet0
     description NAC - Internal network
     switchport access vlan 100
     no ip address
    interface FastEthernet1
     description NAC - Guest network
     switchport access vlan 200
     no ip address
    interface FastEthernet2
     no ip address
     shutdown
    interface FastEthernet3
     description **** WAN Port ****
     switchport access vlan 500
     no ip address
    interface Vlan1
     no ip address
     bridge-group 10
     hold-queue 100 out
    interface Vlan100
     description NAC - Internal Vlan
     ip address 192.168.1.1 255.255.255.0
     ip access-group IN-100 in
     ip access-group OUT-100 out
     ip nat inside
     ip virtual-reassembly in
    interface Vlan200
     description NAC - Guest Vlan
     ip address 10.1.1.1 255.255.255.0
     ip access-group IN-200 in
     ip access-group OUT-200 out
     ip nat inside
     ip virtual-reassembly in
    interface Vlan500
     description **** WAN Vlan ****
     ip address dhcp
     ip nat outside
     no ip virtual-reassembly in
    no ip forward-protocol nd
    ip http server
    ip http access-class 23
    ip http secure-server
    ip dns server
    ip nat inside source list NAT-100 interface Vlan500 overload
    ip nat inside source list NAT-200 interface Vlan500 overload
    ip nat inside source static tcp 192.168.1.123 25 interface Vlan500 25
    ip nat inside source static tcp 192.168.1.123 443 interface Vlan500 443
    ip nat inside source static tcp 192.168.1.123 3389 interface Vlan500 3399
    ip nat inside source static tcp 192.168.1.123 80 interface Vlan500 80
    ip nat inside source static tcp 192.168.1.123 4125 interface Vlan500 4125
    ip nat inside source static tcp 192.168.1.124 3389 interface Vlan500 3390
    ip nat inside source static tcp 192.168.1.123 987 interface Vlan500 987
    ip nat inside source static tcp 192.168.1.123 1723 interface Vlan500 1723
    ip route 0.0.0.0 0.0.0.0 55.234.52.43
    ip access-list extended IN-100
     permit udp any any range bootps bootpc
     deny   ip 10.1.1.0 0.0.0.255 any
     permit ip 192.168.1.0 0.0.0.255 any
    ip access-list extended IN-200
     permit udp any any range bootps bootpc
     permit ip 10.1.1.0 0.0.0.255 any
    ip access-list extended NAT-100
     deny   ip 192.168.0.0 0.0.255.255 192.168.0.0 0.0.255.255
     permit ip 192.168.1.0 0.0.0.255 any
    ip access-list extended NAT-200
     deny   ip 10.1.0.0 0.0.255.255 10.1.0.0 0.0.255.255
     permit ip 10.1.1.0 0.0.0.255 any
    ip access-list extended OUT-100
     permit udp any range bootps bootpc any
     deny   ip 10.1.1.0 0.0.0.255 any
     permit ip any 192.168.1.0 0.0.0.255
    ip access-list extended OUT-200
     permit udp any range bootps bootpc any
     deny   ip 10.1.1.0 0.0.0.255 192.168.1.0 0.0.0.255
     permit ip any 10.1.1.0 0.0.0.255
    access-list 23 permit 59.23.164.52
    access-list 23 permit 192.168.1.0 0.0.0.255
    access-list 23 permit 10.1.1.0 0.0.0.255
    access-list 23 permit 120.146.0.0 0.0.255.255
    access-list 23 permit 149.185.12.0 0.0.0.255
    access-list 23 permit 110.44.28.0 0.0.0.255
    access-list 23 permit 110.44.26.0 0.0.0.255
    access-list 23 permit 103.25.212.0 0.0.0.255
    access-list 23 permit any
    bridge 10 protocol ieee
    banner motd ^C
    *      Authorized personnel only!       *
    ^C
    line con 0
     login local
     no modem enable
    line aux 0
    line vty 0 4
     password password01
     login local
     transport input all
    end

  • Cisco 1941 Router-on-a-Stick w/ 11VLANs trunked to a Cisco 2960: Can Ping a device in another VLAN, that device cannot ping back

    Cisco 1941 Router-on-a-Stick w/ 11VLANs trunked to a Cisco 2960: From the Switch I can Ping a device in another VLAN, that device cannot ping back. Some devices can ping devices in other VLANs and the device in the other VLAN can successfully return the Ping. Have a look at the attached diagram.
    Router Config:
    show run
    Building configuration...
    Current configuration : 7224 bytes
    ! Last configuration change at 09:05:48 EDT Wed Aug 6 2014
    version 15.2
    service timestamps debug datetime msec
    service timestamps log datetime msec
    no service password-encryption
    hostname ROUTER
    boot-start-marker
    boot-end-marker
    no aaa new-model
    clock timezone EDT -8 0
    ip cef
    ip name-server 8.8.8.8
    no ipv6 cef
    multilink bundle-name authenticated
    license udi pid CISCO1941/K9
    object-group network Net_Obj_Group1 
     description This network group allows all 10.0.0.0 and Email Forwarder server through to the Plt PCs
     205.191.0.0 255.255.0.0
     10.0.0.0 255.0.0.0
    object-group network Net_Obj_Group2 
     description This Network Group includes the Host IPs allowed through the Plant Router
     host 10.194.28.23
     host 10.194.28.25
     host 10.194.28.26
     host 10.194.28.27
     host 10.194.28.28
     host 10.194.28.29
     host 10.194.28.37
     host 10.194.28.39
     host 10.194.28.40
     host 10.194.28.70
     host 10.194.28.130
     host 10.194.28.131
     host 10.194.28.132
     host 10.194.28.133
     host 10.194.28.134
     host 10.194.28.135
     host 10.194.28.136
     host 10.194.28.137
     host 10.194.28.138
     host 10.194.28.139
     host 10.194.28.140
     host 10.194.28.141
    interface Embedded-Service-Engine0/0
     no ip address
     shutdown
    interface GigabitEthernet0/0
     description Port Ge0/0 to IT Enterprise network Switch GE1/0/38
     ip address 10.194.28.111 255.255.255.0
     ip access-group 105 in
     ip access-group 106 out
     ip nat outside
     ip virtual-reassembly in
     shutdown
     duplex full
     speed auto
     no mop enabled
    interface GigabitEthernet0/1
     description Port to Plant PCN-K/L24 Sw1 Port 0/24
     no ip address
     duplex auto
     speed auto
     no mop enabled
    interface GigabitEthernet0/1.102
     description Port to VLAN 102
     encapsulation dot1Q 102
     ip address 192.168.102.1 255.255.255.0
     ip nat inside
     ip virtual-reassembly in
    interface GigabitEthernet0/1.104
     description Port to VLAN 104
     encapsulation dot1Q 104
     ip address 192.168.104.1 255.255.255.0
     ip nat inside
     ip virtual-reassembly in
    interface GigabitEthernet0/1.105
     description Port to VLAN 105
     encapsulation dot1Q 105
     ip address 192.168.105.1 255.255.255.0
     ip nat inside
     ip virtual-reassembly in
    interface GigabitEthernet0/1.106
     description Port to VLAN 106
     encapsulation dot1Q 106
     ip address 192.168.106.1 255.255.255.0
     ip nat inside
     ip virtual-reassembly in
    interface GigabitEthernet0/1.107
     description Port to VLAN 107
     encapsulation dot1Q 107
     ip address 192.168.107.1 255.255.255.0
     ip nat inside
     ip virtual-reassembly in
    interface GigabitEthernet0/1.111
     description Port to VLAN 111
     encapsulation dot1Q 111
     ip address 192.168.111.1 255.255.255.0
     ip nat inside
     ip virtual-reassembly in
    interface GigabitEthernet0/1.117
     description Port to VLAN 117
     encapsulation dot1Q 117
     ip address 192.168.117.1 255.255.255.0
     ip nat inside
     ip virtual-reassembly in
    interface GigabitEthernet0/1.121
     description Port to VLAN 121
     encapsulation dot1Q 121
     ip address 192.168.121.1 255.255.255.0
     ip nat inside
     ip virtual-reassembly in
    interface GigabitEthernet0/1.125
     description Port to VLAN 125
     encapsulation dot1Q 125
     ip address 192.168.125.1 255.255.255.0
     ip nat inside
     ip virtual-reassembly in
    interface GigabitEthernet0/1.150
     description Port to to VLAN 150
     encapsulation dot1Q 150
     ip address 192.168.150.1 255.255.255.0
     ip nat inside
     ip virtual-reassembly in
    interface GigabitEthernet0/1.999
     description Port to VLAN 999
     encapsulation dot1Q 999
     ip address 192.168.0.1 255.255.255.0
     ip nat inside
     ip virtual-reassembly in
    ip forward-protocol nd
    ip http server
    no ip http secure-server
    ip nat inside source static 192.168.102.201 10.194.28.23
    ip nat inside source static 192.168.121.201 10.194.28.25
    ip nat inside source static 192.168.106.251 10.194.28.26
    ip nat inside source static 192.168.107.245 10.194.28.27
    ip nat inside source static 192.168.102.251 10.194.28.28
    ip nat inside source static 192.168.150.201 10.194.28.29
    ip nat inside source static 192.168.107.179 10.194.28.37
    ip nat inside source static 192.168.111.201 10.194.28.39
    ip nat inside source static 192.168.105.201 10.194.28.40
    ip nat inside source static 192.168.106.21 10.194.28.70
    ip nat inside source static 192.168.107.146 10.194.28.130
    ip nat inside source static 192.168.107.156 10.194.28.131
    ip nat inside source static 192.168.107.161 10.194.28.132
    ip nat inside source static 192.168.107.181 10.194.28.133
    ip nat inside source static 192.168.107.191 10.194.28.134
    ip nat inside source static 192.168.106.202 10.194.28.135
    ip nat inside source static 192.168.106.212 10.194.28.136
    ip nat inside source static 192.168.117.190 10.194.28.137
    ip nat inside source static 192.168.117.100 10.194.28.138
    ip nat inside source static 192.168.106.242 10.194.28.139
    ip nat inside source static 192.168.125.100 10.194.28.140
    ip nat inside source static 192.168.125.99 10.194.28.141
    ip nat outside source static 10.194.28.23 10.194.28.23
    ip nat outside source static 10.194.28.25 10.194.28.25
    ip nat outside source static 10.194.28.26 10.194.28.26
    ip nat outside source static 10.194.28.27 10.194.28.27
    ip nat outside source static 10.194.28.28 10.194.28.28
    ip nat outside source static 10.194.28.29 10.194.28.29
    ip nat outside source static 10.194.28.37 10.194.28.37
    ip nat outside source static 10.194.28.39 10.194.28.39
    ip nat outside source static 10.194.28.40 10.194.28.40
    ip nat outside source static 10.194.28.70 10.194.28.70
    ip nat outside source static 10.194.28.130 10.194.28.130
    ip nat outside source static 10.194.28.131 10.194.28.131
    ip nat outside source static 10.194.28.132 10.194.28.132
    ip nat outside source static 10.194.28.133 10.194.28.133
    ip nat outside source static 10.194.28.134 10.194.28.134
    ip nat outside source static 10.194.28.135 10.194.28.135
    ip nat outside source static 10.194.28.136 10.194.28.136
    ip nat outside source static 10.194.28.137 10.194.28.137
    ip nat outside source static 10.194.28.138 10.194.28.138
    ip nat outside source static 10.194.28.139 10.194.28.139
    ip nat outside source static 10.194.28.140 10.194.28.140
    ip nat outside source static 10.194.28.141 10.194.28.141
    ip route 0.0.0.0 0.0.0.0 10.194.28.1
    access-list 105 permit ip object-group Net_Obj_Group1 object-group Net_Obj_Group2
    access-list 106 permit ip object-group Net_Obj_Group2 object-group Net_Obj_Group1
    dialer-list 1 protocol ip permit
    control-plane
    banner login ^CC
    Login banner for Plant Router #01^C
    banner motd ^CC
    MOTD Banner for Plant Router^C
    line con 0
     password XXXXXXXXX
     logging synchronous
     login
    line aux 0
    line 2
     no activation-character
     no exec
     transport preferred none
     transport output pad telnet rlogin lapb-ta mop udptn v120 ssh
     stopbits 1
    line vty 0 4
     password XXXXXXXXX
     logging synchronous
     login
     transport input all
    scheduler allocate 20000 1000
    ntp server 10.199.100.92
    end
    Switch Config:
    sh ru
    Building configuration...
    Current configuration : 6513 bytes
    version 12.2
    no service pad
    service timestamps debug uptime
    service timestamps log datetime localtime show-timezone
    service password-encryption
    hostname K24Sw01
    boot-start-marker
    boot-end-marker
    no aaa new-model
    clock timezone EDT -5
    clock summer-time EDT recurring
    udld aggressive
    crypto pki trustpoint TP-self-signed-593746944
     enrollment selfsigned
     subject-name cn=IOS-Self-Signed-Certificate-593746944
     revocation-check none
     rsakeypair TP-self-signed-593746944
      4B58BCE9 44
      quit
    spanning-tree mode pvst
    spanning-tree extend system-id
    vlan internal allocation policy ascending
    interface FastEthernet0
     no ip address
    interface GigabitEthernet0/1
     description Trunk port for vlans 105, 111, 125 and 999 from K24Sw01 port Ge0/1 to P22Sw01 port Ge0/24
     switchport trunk allowed vlan 105,111,125,999
     switchport mode trunk
    interface GigabitEthernet0/2
     description Trunk port for vlans 150 and 999 from K24Sw01 port Ge0/2 to N25Sw01 port Ge0/26
     switchport trunk allowed vlan 150,999
     switchport mode trunk
    interface GigabitEthernet0/3
     description Trunk port for vlans 102, 104, 106, 107, 117 and 999 from K24Sw01 port Ge0/3 to K28Sw01 port Ge0/26
     switchport trunk allowed vlan 102,104,106,107,117,999
     switchport mode trunk
    interface GigabitEthernet0/4
     description Trunk port for vlans 102, 106, 107 and 999 from K24Sw01 port Ge0/4 to H23Sw01 port Ge0/26
     switchport trunk allowed vlan 102,106,107,999
     switchport mode trunk
    interface GigabitEthernet0/5
     description Trunk port for vlans 121, 125 and 999 from K24Sw01 port Ge0/5 to M21Sw01 port Ge0/24
     switchport trunk allowed vlan 121,125,999
     switchport mode trunk
    interface GigabitEthernet0/6
     description OPEN
     spanning-tree portfast
    interface GigabitEthernet0/7
     description OPEN
     spanning-tree portfast
    interface GigabitEthernet0/8
     description OPEN
     spanning-tree portfast
    interface GigabitEthernet0/9
     description OPEN
     spanning-tree portfast
    interface GigabitEthernet0/10
     description VLan 102 access port
     switchport access vlan 102
     spanning-tree portfast
    interface GigabitEthernet0/11
     description - VLan 104 access port
     switchport access vlan 104
     spanning-tree portfast
    interface GigabitEthernet0/12
     description - VLan 105 access port
     switchport access vlan 105
     spanning-tree portfast
    interface GigabitEthernet0/13
     description - VLan 106 access port
     switchport access vlan 106
     spanning-tree portfast
    interface GigabitEthernet0/14
     description - VLan 107 access port
     switchport access vlan 107
     spanning-tree portfast
    interface GigabitEthernet0/15
     description - VLan 111 access port
     switchport access vlan 111
     spanning-tree portfast
    interface GigabitEthernet0/16
     description - VLan 117 access port
     switchport access vlan 117
     spanning-tree portfast
    interface GigabitEthernet0/17
     description - VLan 121 access port
     switchport access vlan 121
     spanning-tree portfast
    interface GigabitEthernet0/18
     description - VLan 125 access port
     switchport access vlan 125
     spanning-tree portfast
    interface GigabitEthernet0/19
     description - VLan 150 access port
     switchport access vlan 150
     spanning-tree portfast
    interface GigabitEthernet0/20
     description - VLan 999 access port
     switchport access vlan 999
     spanning-tree portfast
    interface GigabitEthernet0/21
     description OPEN
     spanning-tree portfast
    interface GigabitEthernet0/22
     description OPEN
     spanning-tree portfast
    interface GigabitEthernet0/23
     description OPEN
     spanning-tree portfast
    interface GigabitEthernet0/24
     description From ROUTER Gw ge0/1
     switchport trunk allowed vlan 102,104-107,111,117,121,125,150,999
     switchport mode trunk
    interface GigabitEthernet0/25
    interface GigabitEthernet0/26
    interface Vlan1
     no ip address
     no ip route-cache
     shutdown
    interface Vlan102
     ip address 192.168.102.253 255.255.255.0
    interface Vlan104
     no ip address
     no ip route-cache
    interface Vlan105
     no ip address
     no ip route-cache
    interface Vlan106
     no ip address
     no ip route-cache
    interface Vlan107
     no ip address
     no ip route-cache
    interface Vlan111
     no ip address
     no ip route-cache
    interface Vlan117
     no ip address
     no ip route-cache
    interface Vlan121
     no ip address
     no ip route-cache
    interface Vlan125
     no ip address
     no ip route-cache
    interface Vlan150
     no ip address
     no ip route-cache
    interface Vlan999
     no ip address
     no ip route-cache
    ip default-gateway 192.168.102.1
    ip http server
    ip http secure-server
    snmp-server engineID local 00000009020000019634C2C0
    snmp-server community public RO
    snmp-server location 
    snmp-server contact 
    banner motd ^CCC ADMIN USE ONLY! ^C
    line con 0
     session-timeout 10 
     password xxxxxx
     logging synchronous
     login
     stopbits 1
    line vty 0 4
     session-timeout 10 
     password xxxxxxx
     login
    line vty 5 15
     session-timeout 10 
     password xxxxxxxx
     login
    ntp server 10.199.100.92
    end
    K24Sw01#

    HI Mark,
    Here is the my config:
    Create sub-interfaces, set 802.1Q trunking protocol and ip address on each sub-interface
    Router(config)#interface f0/0
    Router(config-if)#no shutdown
    (Note: The main interface f0/0 doesn’t need an IP address but it must be turned on)
    Router(config)#interface f0/0.10
    Router(config-subif)#encapsulation dot1q 10
    Router(config-subif)#ip address 192.168.10.1 255.255.255.0
    Router(config-subif)#interface f0/0.20
    Router(config-subif)#encapsulation dot11 20
    Router(config-subif)#ip address 192.168.20.1 255.255.255.0
    (Note: In the “encapsulation dot1q 10″ command, 10 is the VLAN ID this interface operates in)
    Configure VLAN
    Switch(config)#vlan 10
    Switch(config-vlan)#name SALES
    Switch(config-vlan)#vlan 20
    Switch(config-vlan)#name TECH
    Set ports to access mode & assign ports to VLAN
    Switch(config)#interface range fa0/1
    Switch(config-if)#no shutdown
    Switch(config-if)# switchport mode access
    Switch(config-if)# switchport access vlan 15
    Switch(config-if)#interface range fa0/3
    Switch(config-if)#no shutdown
    Switch(config-if)#switchport mode access
    Switch(config-if)# switchport access vlan 20
    Switch(config-if)#interface range fa0/5
    Switch(config-if)#no shutdown
    Switch(config-if)#switchport mode trunk
    1. Please check all your port are up.
    2. Check the config once again.
    3. Make sure the swicth and router connection port configured as trunk and it should be up.
    This config is working for me,
    Regards
    Dont forget to rate helpful posts.

  • I am loosing configuration when I power off my Cisco 857 router

    I bought new Cisco 857 router from the shop. Router must have been used before as I couln't go in with default username/password cisco/cisco.
    Well I followed instruciton and reset password to username and password. Now I finally connected to the Cisco CP express over my IE browser.
    I found out that somebody was using a router from the shop so this is why I coun't log to it in the first place. Anyway problem is that when I changed configuration and applied settings it remembers it until I power it off. When I power it on again it remembers all settings from that shop.
    It reverts everything back: IP address, previous level 15 account and password - everything like after password reset.
    I tried it again and it again lost settings. So I found following instruction:
    http://www.cisco.com/en/US/products/hw/routers/ps233/products_tech_note09186a00800a65a5.shtml
    I followed it and changed again all settings on the router. My settings are again lost after power off/on. I noticed that when I do first bit it does show
    0x2102 not 0x2142 like they think that is password reset mode.
    Here is my output from Hyper Terminal:
    =============================
    Cisco#enableCisco#show startUsing 3359 out of 131072 bytes!version 12.4no service padservice timestamps debug datetime msecservice timestamps log datetime msecno service password-encryption!hostname Cisco!boot-start-markerboot-end-marker!logging buffered 51200 warningsenable secret 5 $1$hpKF$Rc1tl6r45J8iHG7EN5jSk.!no aaa new-model!crypto pki trustpoint TP-self-signed-3185909327 enrollment selfsigned subject-name cn=IOS-Self-Signed-Certificate-3185909327 revocation-check none rsakeypair TP-self-signed-3185909327!!crypto pki certificate chain TP-self-signed-3185909327 certificate self-signed 01 nvram:IOS-Self-Sig#5.cerdot11 syslogno ip dhcp use vrf connectedip dhcp excluded-address 10.10.10.1!ip dhcp pool ccp-pool   import all   network 10.10.10.0 255.255.255.248   default-router 10.10.10.1   lease 0 2!!ip cefno ip domain lookupip domain name molinary.com!!!username admin privilege 15 secret 5 $1$jD3j$r6ROikgGsIlcMTGjkxFQ6.username username privilege 15 password 0 password!!archive log config  hidekeys!!!!!interface ATM0 no ip address shutdown no atm ilmi-keepalive dsl operating-mode auto!interface ATM0.1 point-to-point description $ES_WAN$ ip nat outside ip virtual-reassembly pvc 0/38  encapsulation aal5mux ppp dialer  dialer pool-member 1 !!interface FastEthernet0!interface FastEthernet1!interface FastEthernet2!interface FastEthernet3!interface Vlan1 description $ETH-SW-LAUNCH$$INTF-INFO-HWIC 4ESW$$ES_LAN$ ip address 10.10.10.1 255.255.255.248 ip nat inside ip virtual-reassembly ip tcp adjust-mss 1452!interface Dialer0 ip address dhcp encapsulation ppp dialer pool 1 dialer-group 1 no cdp enable ppp authentication chap pap callin ppp chap hostname [email protected] ppp chap password 0 netgear01 ppp pap sent-username [email protected] password 0 netgear01!ip forward-protocol nd!ip http serverip http access-class 23ip http authentication localip http secure-serverip http timeout-policy idle 60 life 86400 requests 10000ip nat inside source list 1 interface ATM0.1 overload!access-list 1 remark INSIDE_IF=Vlan1access-list 1 remark CCP_ACL Category=2access-list 1 permit 10.10.10.0 0.0.0.7dialer-list 1 protocol ip permitno cdp run!control-plane!banner exec ^C% Password expiration warning.-----------------------------------------------------------------------Cisco Configuration Professional (Cisco CP) is installed on this deviceand it provides the default username "cisco" for  one-time use. If you havealready used the username "cisco" to login to the router and your IOS imagesupports the "one-time" user option, then this username has already expired.You will not be able to login to the router with this username after you exitthis session.It is strongly suggested that you create a new username with a privilege levelof 15 using the following command.username <myuser> privilege 15 secret 0 <mypassword>Replace <myuser> and <mypassword> with the username and password youwant to use.-----------------------------------------------------------------------^Cbanner login ^CAuthorized access only! Disconnect IMMEDIATELY if you are not an authorized user!^C!line con 0 login local no modem enableline aux 0line vty 0 4 privilege level 15 login local transport input telnet ssh!scheduler max-task-time 5000endCisco#Cisco#Cisco#Cisco#Cisco#Cisco#Cisco#Cisco#Cisco#show versionCisco IOS Software, C850 Software (C850-ADVSECURITYK9-M), Version 12.4(15)T12, RELEASE SOFTWARE (fc3)Technical Support: http://www.cisco.com/techsupportCopyright (c) 1986-2010 by Cisco Systems, Inc.Compiled Fri 22-Jan-10 14:46 by prod_rel_teamROM: System Bootstrap, Version 12.3(8r)YI4, RELEASE SOFTWARECisco uptime is 20 minutesSystem returned to ROM by power-onSystem image file is "flash:c850-advsecurityk9-mz.124-15.T12.bin"This product contains cryptographic features and is subject to UnitedStates and local country laws governing import, export, transfer anduse. Delivery of Cisco cryptographic products does not implythird-party authority to import, export, distribute or use encryption.Importers, exporters, distributors and users are responsible forcompliance with U.S. and local country laws. By using this product youagree to comply with applicable laws and regulations. If you are unableto comply with U.S. and local laws, return this product immediately.A summary of U.S. laws governing Cisco cryptographic products may be found at:http://www.cisco.com/wwl/export/crypto/tool/stqrg.htmlIf you require further assistance please contact us by sending email [email protected] 857 (MPC8272) processor (revision 0x400) with 59392K/6144K bytes of memory.Processor board ID FCZ140792J5MPC8272 CPU Rev: Part Number 0xC, Mask Number 0x104 FastEthernet interfaces1 ATM interface128K bytes of non-volatile configuration memory.20480K bytes of processor board System flash (Intel Strataflash)Configuration register is 0x2102Cisco#Cisco#Cisco#Cisco#endTranslating "end"% Unknown command or computer name, or unable to find computer addressCisco#reloadProceed with reload? [confirm]*Mar  1 01:19:27.786: %SYS-5-RELOAD: Reload requested  by username on console. Reload Reason: Reload Command.System Bootstrap, Version 12.3(8r)YI4, RELEASE SOFTWARETechnical Support: http://www.cisco.com/techsupportCopyright (c) 2006 by cisco Systems, Inc.C850 series (Board ID: 2-149) platform with 65536 Kbytes of main memoryBooting flash:/c850-advsecurityk9-mz.124-15.T12.binSelf decompressing the image : ############################################## [OK]              Restricted Rights LegendUse, duplication, or disclosure by the Government issubject to restrictions as set forth in subparagraph(c) of the Commercial Computer Software - RestrictedRights clause at FAR sec. 52.227-19 and subparagraph(c) (1) (ii) of the Rights in Technical Data and ComputerSoftware clause at DFARS sec. 252.227-7013.           cisco Systems, Inc.           170 West Tasman Drive           San Jose, California 95134-1706Cisco IOS Software, C850 Software (C850-ADVSECURITYK9-M), Version 12.4(15)T12, RELEASE SOFTWARE (fc3)Technical Support: http://www.cisco.com/techsupportCopyright (c) 1986-2010 by Cisco Systems, Inc.Compiled Fri 22-Jan-10 14:46 by prod_rel_teamImage text-base: 0x8002007C, data-base: 0x814E7240This product contains cryptographic features and is subject to UnitedStates and local country laws governing import, export, transfer anduse. Delivery of Cisco cryptographic products does not implythird-party authority to import, export, distribute or use encryption.Importers, exporters, distributors and users are responsible forcompliance with U.S. and local country laws. By using this product youagree to comply with applicable laws and regulations. If you are unableto comply with U.S. and local laws, return this product immediately.A summary of U.S. laws governing Cisco cryptographic products may be found at:http://www.cisco.com/wwl/export/crypto/tool/stqrg.htmlIf you require further assistance please contact us by sending email [email protected] 857 (MPC8272) processor (revision 0x400) with 59392K/6144K bytes of memory.Processor board ID FCZ140792J5MPC8272 CPU Rev: Part Number 0xC, Mask Number 0x104 FastEthernet interfaces1 ATM interface128K bytes of non-volatile configuration memory.20480K bytes of processor board System flash (Intel Strataflash)no ip dhcp use vrf connected               ^% Invalid input detected at '^' marker.SETUP: new interface NVI0 placed in "shutdown" statePress RETURN to get started!*Mar  1 00:00:03.952: %VPN_HW-6-INFO_LOC: Crypto engine: onboard 0  State changed to: Initialized*Mar  1 00:00:03.960: %VPN_HW-6-INFO_LOC: Crypto engine: onboard 0  State changed to: Enabled*Mar  1 00:00:07.244: %LINK-3-UPDOWN: Interface FastEthernet0, changed state toup*Mar  1 00:00:08.413: %LINEPROTO-5-UPDOWN: Line protocol on Interface FastEthernet0, changed state to up*Mar  1 00:00:08.821: %SYS-5-CONFIG_I: Configured from memory by console*Mar  1 01:19:27.072: %LINK-3-UPDOWN: Interface Virtual-Access1, changed state to up*Mar  1 01:19:27.352: %SYS-5-RESTART: System restarted --Cisco IOS Software, C850 Software (C850-ADVSECURITYK9-M), Version 12.4(15)T12, RELEASE SOFTWARE (fc3)Technical Support: http://www.cisco.com/techsupportCopyright (c) 1986-2010 by Cisco Systems, Inc.Compiled Fri 22-Jan-10 14:46 by prod_rel_team*Mar  1 01:19:27.352: %SNMP-5-COLDSTART: SNMP agent on host Cisco is undergoinga cold start*Mar  1 01:19:27.436: %CRYPTO-6-ISAKMP_ON_OFF: ISAKMP is OFF*Mar  1 01:19:27.436: %CRYPTO-6-ISAKMP_ON_OFF: ISAKMP is OFF*Mar  1 01:19:27.540: %LINEPROTO-5-UPDOWN: Line protocol on Interface NVI0, changed state to down*Mar  1 01:19:28.072: %LINEPROTO-5-UPDOWN: Line protocol on Interface Virtual-Access1, changed state to up*Mar  1 01:19:28.484: %LINEPROTO-5-UPDOWN: Line protocol on Interface Vlan1, changed state to up*Mar  1 01:19:28.484: %LINK-5-CHANGED: Interface ATM0, changed state to administratively down*Mar  1 01:19:28.848: %LINK-5-CHANGED: Interface NVI0, changed state to administratively down*Mar  1 01:19:28.932: %LINK-3-UPDOWN: Interface FastEthernet3, changed state toup*Mar  1 01:19:28.936: %LINK-3-UPDOWN: Interface FastEthernet2, changed state toup*Mar  1 01:19:28.940: %LINK-3-UPDOWN: Interface FastEthernet1, changed state toup*Mar  1 01:19:29.484: %LINEPROTO-5-UPDOWN: Line protocol on Interface ATM0, changed state to down*Mar  1 01:19:29.932: %LINEPROTO-5-UPDOWN: Line protocol on Interface FastEthernet3, changed state to down*Mar  1 01:19:29.936: %LINEPROTO-5-UPDOWN: Line protocol on Interface FastEthernet2, changed state to down*Mar  1 01:19:29.940: %LINEPROTO-5-UPDOWN: Line protocol on Interface FastEthernet1, changed state to down*Mar  1 01:19:29.948: %LINEPROTO-5-UPDOWN: Line protocol on Interface FastEthernet0, changed state to upAuthorized access only!===========================================
    Please help me as I am stuck and can't go any further....

    Hi David White,
    Alternatively, after password recovery you can modify the configuration to be what you want, and then issue:
       write memory
    to save the configuration.  You can then verify that your changes have been saved to the startup config by issuing:
       show startup-config"
    The only good thing is that when I switch off a router it erase configuration except my new password which I created after password reset. Everything else is getting vanished (ADSL settings, DHCP, routing ) everything. Even new admin accounts I created.
    Well have a question to your above comments. I am new in Cisco so please put as much detail as you can for me to understand. When you say modify configuration do you mean to go to Cisco CP Express graphical interface and then connect router to hyper terminal and execute above commands?
    Why router doesn't remember this anyway. There must be some option to change in configuration to make thing permanent when I hit apply changes in Cisco CO Express otherwise it is pointless to heve it.
    Phillip
    write memory
    is
    copy running-config startup-config"
    Can't this be done via Cisco CP Express or set up router to copy this every time I change this in graphical interface rather going to command line to achnoledge it?
    I understand your concern about this router and somebodie's configuration details as you want things to be un-used when you buy them - true. ADSL details belongs to the shop which sold me the router so that is why I don't make a big problem about this. We take most of hardware from this shop and have discount and many good deals with them so I think they have been just testing it and forgot to erease their config. It might be that someone has returned router to the shop and they have repaired it and tested it.
    I hope this is a normal behaviour of this router as I have option to replace it in case this is a fault.
    Could you please write me step by step guide how can I make changed options stay permanently on router?
    thank you
    Dragan

  • I have a Cisco wireless router.  Can I buy an Airport Express plug in booster for a distant part of my house or do I need an Airport Extreme base station instead to make the Airport Express plug in booster work?

    Can I buy an Airport Express plug-in wifi signal booster to connect to a Cisco wireless router, or do I have to buy an Airport Extreme base station to make the Airport Express plug-in work?

    You would need either an AirPort Extreme or an AirPort Express connected to the Cisco router, with a permanent Ethernet cable connection.
    Configure the Extreme or Express that is connected to the Cisco router to "create a wireless network".
    Then, you could add an AirPort Express to "extend a wireless network" to provide more wireless coverage for the network that the Extreme or Express would be creating.
    Remember that the Express can only "extend" the quality of signal that it receives, so it must be located where it can receive a strong signal from the "main" AirPort.
    If you don't need the Cisco wireless signal, you could turn it off.....or use that network for guests or something similar.
    The bottom line here......you always need two Apple routers if you want to extend the network wirelessly.

  • Cisco 2951 router AC-PoE power consumption, meaning of the mention "Platform Only" in the datasheet.

    Hello,
    I have a question regarding the power consumption of a Cisco 2951 router with an AC-PoE power supply (without PoE boost).
    In fact in the table (n°7) of the Cisco 2900 Series ISR (G2) datasheet, that sum up the power consumption data for Cisco 2900 series routers there is the line : "Maximum Power with PoE Power Supply (Platform Only) (Watts)", and I would like to know what is exactly the meaning about the mention "Platform Only".
    Thank you for your help, best regards,

    Hi @francois.trarieux,
    This is the maximum power that is consumed exclusively by the router from the PoE PS (Power Supply). The power capacity that the PoE PS gives to other PoE devices (IP Phones, Cameras, APs, etc) is specified in the line below "Maximum End-Point PoE Power  Available from PoE Power Supply (Watts)" of the datasheet.
    HTH.
    Regards,
    Martin, IT Specialist

  • Configuration Issue with my Cisco 871 Router

    Hi all,
    I am a newbie to the Cisco IOS.
    I got a Cisco 871 Router that I'd like to use for internet connection. My LAN network is 192.168.1.0/24 and the ISP has assigned us the IP 41.212.79.108/24 and gateway 41.212.79.1.
    With my current configuration, I can hit the router - 192.168.1.1 - and it's WAN port - 41.212.79.108 - but not the gateway.
    Below is my current config:
    Hoggers#show config
    Using 4414 out of 131072 bytes
    version 12.4
    no service pad
    service timestamps debug datetime msec
    service timestamps log datetime msec
    no service password-encryption
    hostname Hoggers
    boot-start-marker
    boot-end-marker
    logging buffered 51200 warnings
    enable secret 5 **********************.
    no aaa new-model
    crypto pki trustpoint TP-self-signed-568493463
    enrollment selfsigned
    subject-name cn=IOS-Self-Signed-Certificate-568493463
    revocation-check none
    rsakeypair TP-self-signed-568493463
    crypto pki certificate chain TP-self-signed-568493463
    certificate self-signed 01 nvram:IOS-Self-Sig#7.cer
    dot11 syslog
    ip cef
    no ip dhcp use vrf connected
    ip dhcp excluded-address 10.10.10.1
    ip dhcp excluded-address 192.168.1.1
    ip dhcp excluded-address 192.168.1.2
    ip dhcp excluded-address 192.168.1.3
    ip dhcp excluded-address 192.168.1.4
    ip dhcp excluded-address 192.168.1.5
    ip dhcp excluded-address 192.168.1.6
    ip dhcp excluded-address 192.168.1.7
    ip dhcp excluded-address 192.168.1.8
    ip dhcp excluded-address 192.168.1.9
    ip dhcp excluded-address 192.168.1.10
    ip dhcp excluded-address 192.168.1.100
    ip dhcp excluded-address 192.168.1.90
    ip dhcp pool ccp-pool
       import all
       network 10.10.10.0 255.255.255.248
       default-router 10.10.10.1
       lease 0 2
    ip dhcp pool LANPOOL
       network 192.168.1.0 255.255.255.0
       default-router 192.168.1.1
       dns-server 41.212.3.2 41.212.3.253
    ip domain name yourdomain.com
    ip name-server 41.212.3.2
    ip name-server 41.212.3.253
    archive
    log config
      hidekeys
    interface FastEthernet0
    interface FastEthernet1
    interface FastEthernet2
    interface FastEthernet3
    interface FastEthernet4
    description Wan to Outside World
    ip address 41.212.79.108 255.255.255.0
    duplex auto
    speed auto
    interface Vlan1
    description $ETH-SW-LAUNCH$$INTF-INFO-HWIC 4ESW$
    ip address 192.168.1.1 255.255.255.0
    ip tcp adjust-mss 1452
    ip forward-protocol nd
    ip route 0.0.0.0 0.0.0.0 41.212.79.1
    ip http server
    ip http access-class 23
    ip http authentication local
    ip http secure-server
    ip http timeout-policy idle 60 life 86400 requests 10000
    ip dns server
    ip nat inside source static tcp 192.168.1.31 80 interface FastEthernet4 80
    access-list 23 permit 10.10.10.0 0.0.0.7
    no cdp run
    control-plane
    scheduler max-task-time 5000
    end
    I'll appreciate any light you can shed on what am missing.

    2 wireless routers can not communicate wirelessly with each other.
    You need to connect cable between 2 routers and use the second wireless router as access point.
    Follow this link to connect Linksys router to another router.
    Some of your devices are getting same IP address. This might be the issue with DHCP server of the router. You can try DHCP reservation on the router so that each device will get unique IP address.

  • How to install 2-port vic3 2fxs/DID and 2-port vic2 fxo on cisco 2801 router

    Hello
    I'm looking for information on how to install 2 newly purchased cards  and keep running into dead links. The cards I bought are for a  CISCO-2801-CCME/K9 with PVDM2-8, FL-CCME-25, SP Services 128F/256D cisco  router:
    vic3 2fxs/DID and a vic2 2fxo.
    I keep finding documents on how to  install these cards but all links are dead and leading to nowhere.
    http://www.cisco.com/en/US/docs/routers/access/interfaces/ic/hardware/installation/guide/2port_FXS_DID_VIC.html#wp1065062
    The  2 documents i'm looking for are: how to install a 2-port vic2 fxo cards on cisco  2801 router and how to install 2-port vic3 2fxs/DID cards on the same 2801 cisco  router.
    NOTE: I've never installed these cards and am not sure if:
    Does my  ios support both of these cards?
    and which slots do I install those in the  router.
    I have 4 slots like this:
    slot 0: This slot only accepts VIC's   ***This could be used for the vic3 2fxs/DID card correct?
    slot 1: Nothing  written here  ****What can i install in this slot?
    slot 2: This slot only  accepts VIC's and WIC's  ***If I buy a WIC and install here which other slot can  i install my VIC2-2FXO card in ?
    slot 3: Nothing written here  ***What can i  install in this slot?
    Any chance someone can help me out with this.
    Thanks  very much

    Ok
    I was able to figure out what goes where and found out that the IOS i had c-2801-spservicesk9-mz.124-15.T10.bin with cme-full-4.1.0.2 tar didn't support the vic3 2fxs/DID card. I then found the one that works which is the c2801-spservicesk9-mz.124-22.YB5.bin.I am now able to see my new hardware interfaces. The question I have now is since the previous version ran with cme-full-4.1.0.2 tar i'm not sure if this needs to be changed since in the compatibility matrix i found this IOS c2801-spservicesk9-mz.124-22.YB5.bin to be compatible with cme-full-7.1.0.0 tar
    Do i need to remove cme-full-4.1.0.2 tar and install the cme-full-7.1.0.0 tar?
    If yes, i know how to install the cme-full-7.1.0.0 tar but how do i remove the other cme-full-4.1.0.2 tar file in order to be able to install the other version?
    Thanks

  • What are the ideal settings for my TC with Shaw's Cisco DPC3825 router/modem

    My old 2nd Gen Time Capsule crapped out and now I am about to set up my new 2TB TC.  My provider is Shaw Communications and they have upgraded me to their Broadband 100 Mbps service.  This came with a new modem/router combo made by Cisco and is model DPC3825.  Before I start plugging things in I'd like to know what are the ideal settings such that I gain the most of the BB100 service.  Should I be setting the Cisco modem/router to Bridge mode or the TC?  Should I have Shaw disable anything?  Any insight is greatly appreciated.

    Unless you specifically need to have the TC perform as the main router for your network, life will be a lot easier if you configure the TC to operate in Bridge Mode.
    Whether the Cisco modem/router or gateway can possibly be configured to act as a simple bridge mode modem is one thing to consider.
    Whether Shaw would support you in the event of any connection difficulties with the modem/router configured this way is another.
    Since Shaw is your provider, it might make sense to talk with them about best practice as far as configuring the DPC3825.
    Once you have that information in hand, you will then have the answer on how best to configure the TC.....which will very likely be in Bridge Mode.

  • Problem with Cisco 861W router and outgoing VPN

    We have a Cisco 861W router that is blocking an outgoing PPTP on the internal access point only. The outgoing VPN works when the traffic is through a wired connection or the connection is on another access point. We fail to make a connection only when connection to the 861W's internal Access Point.
    Here is the Access Point Configuration:
    Current configuration : 2100 bytes
    version 12.4
    no service pad
    service timestamps debug datetime msec
    service timestamps log datetime msec
    no service password-encryption
    hostname obap
    enable secret 5 $1$.1RF$go1D7WITXUn3s8TUaw3tC.
    no aaa new-model
    dot11 syslog
    dot11 ssid OLIVER
       authentication open
       authentication key-management wpa
       guest-mode
       wpa-psk ascii 0 XXXXXXXXXXX
    username XXXXXX privilege 15 secret 5 $1$Wc0K$OzcQDDQfjHP6La31eXMoG/
    bridge irb
    interface Dot11Radio0
    no ip address
    no ip route-cache
    encryption mode ciphers aes-ccm tkip
    ssid OLIVER
    antenna gain 0
    station-role root
    bridge-group 1
    bridge-group 1 subscriber-loop-control
    bridge-group 1 block-unknown-source
    no bridge-group 1 source-learning
    no bridge-group 1 unicast-flooding
    bridge-group 1 spanning-disabled
    interface GigabitEthernet0
    description the embedded AP GigabitEthernet 0 is an internal interface connecti
    ng AP with the host router
    no ip address
    no ip route-cache
    bridge-group 1
    no bridge-group 1 source-learning
    bridge-group 1 spanning-disabled
    interface BVI1
    ip address 192.168.0.2 255.255.255.0
    no ip route-cache
    ip http server
    no ip http secure-server
    ip http help-path http://www.cisco.com/warp/public/779/smbiz/prodconfig/help/eag
    bridge 1 route ip
    banner login ^CC
    % Password change notice.
    Default username/password setup on AP is cisco/cisco with priv¾ilege level 15.
    It is strongly suggested that you create a new username with privilege level
    15 using the following command for console security.
    username <myuser> privilege 15 secret 0 <mypassword>
    no username cisco
    Replace <myuser> and <mypassword> with the username and password you want to
    use. After you change your username/password you can turn off this message
    by configuring  "no banner login" and "no banner exec" in privileged mode.
    ^C
    line con 0
    privilege level 15
    login local
    no activation-character
    line vty 0 4
    login local
    cns dhcp
    end
    obap#
    Here is the Router's Configuration:
    Current configuration : 5908 bytes
    ! No configuration change since last restart
    version 15.0
    no service pad
    service tcp-keepalives-in
    service tcp-keepalives-out
    service timestamps debug datetime msec localtime show-timezone
    service timestamps log datetime msec localtime show-timezone
    service password-encryption
    service sequence-numbers
    hostname obrouter
    boot-start-marker
    boot-end-marker
    logging buffered 51200
    logging console critical
    enable secret 5 $1$i9XE$DjxFVAEC9nC4/r6EQKCd6/
    no aaa new-model
    memory-size iomem 10
    clock timezone PCTime -5
    clock summer-time PCTime date Apr 6 2003 2:00 Oct 26 2003 2:00
    crypto pki trustpoint TP-self-signed-1856757619
    enrollment selfsigned
    subject-name cn=IOS-Self-Signed-Certificate-1856757619
    revocation-check none
    rsakeypair TP-self-signed-1856757619
    crypto pki certificate chain TP-self-signed-1856757619
    certificate self-signed 01
      3082024D 308201B6 A0030201 02020101 300D0609 2A864886 F70D0101 04050030
      31312F30 2D060355 04031326 494F532D 53656C66 2D536967 6E65642D 43657274
      69666963 6174652D 31383536 37353736 3139301E 170D3036 30313032 31323030
      34345A17 0D323030 31303130 30303030 305A3031 312F302D 06035504 03132649
      4F532D53 656C662D 5369676E 65642D43 65727469 66696361 74652D31 38353637
      35373631 3930819F 300D0609 2A864886 F70D0101 01050003 818D0030 81890281
      8100B1A4 FB786547 3D582260 03DB768D 116BDE9A 309FBA04 B53F77B0 BFE32344
      7C3439B3 97192B36 760A9411 1D5C7549 8D86F532 ABA44F53 0D08B7F4 A9A747D5
      071330C3 65BF25A8 927F3596 29BB5A80 90C8D169 22268476 3B8DDE1E FDB7170D
      B4820D03 5580A849 A92C7E76 9AC10867 505A2FEE 64360741 7F9DBDBF 3D79982C
      F81D0203 010001A3 75307330 0F060355 1D130101 FF040530 030101FF 30200603
      551D1104 19301782 156F6272 6F757465 722E6272 75736868 6F672E63 6F6D301F
      0603551D 23041830 168014D8 5BC2FFB2 967A4C7B 11B44122 5C8D31F7 749B9230
      1D060355 1D0E0416 0414D85B C2FFB296 7A4C7B11 B441225C 8D31F774 9B92300D
      06092A86 4886F70D 01010405 00038181 005901F1 C239074B B8213567 CF7B65BF
      DAFE4557 69B2A3B1 5F2593C7 A54B9598 23FD5E7A 563AA6E0 AFB25801 FA0061E8
      F9545372 DB600B3A BE68AE65 1EDA593E 6A0C96B8 5A4136AF 393F9AAC 651E1C36
      B8B7C6C0 47936C24 D2ECE9A5 9446EE32 FC7461FA AD8CF1CE A7FBF341 07E9C3C6
      505AB88D 0E7FCAFC 5792298A E5E4D1FE CC
            quit
    no ip source-route
    ip dhcp excluded-address 192.168.0.1 192.168.0.99
    ip dhcp pool ccp-pool1
       import all
       network 192.168.0.0 255.255.255.0
       dns-server 216.49.160.10 216.49.160.66
       default-router 192.168.0.1
    ip cef
    no ip bootp server
    ip domain name brushhog.com
    ip name-server 216.49.160.10
    ip name-server 216.49.160.66
    license udi pid CISCO861W-GN-A-K9 sn FTX155281FY
    username tech38 privilege 15 secret 5 $1$d/4Z$n/23EsXbzfHF5XfJ8Nv.y0
    ip tcp synwait-time 10
    ip ssh time-out 60
    ip ssh authentication-retries 2
    interface FastEthernet0
    interface FastEthernet1
    interface FastEthernet2
    interface FastEthernet3
    interface FastEthernet4
    description $ES_WAN$$FW_OUTSIDE$
    no ip address
    no ip redirects
    no ip unreachables
    no ip proxy-arp
    ip flow ingress
    duplex auto
    speed auto
    pppoe-client dial-pool-number 1
    interface wlan-ap0
    description Service module interface to manage the embedded AP
    ip unnumbered Vlan1
    no ip redirects
    no ip unreachables
    no ip proxy-arp
    ip flow ingress
    arp timeout 0
    interface Wlan-GigabitEthernet0
    description Internal switch interface connecting to the embedded AP
    interface Vlan1
    description $ETH-SW-LAUNCH$$INTF-INFO-HWIC 4ESW$$ES_LAN$$FW_INSIDE$
    ip address 192.168.0.1 255.255.255.0
    no ip redirects
    no ip unreachables
    no ip proxy-arp
    ip flow ingress
    ip nat inside
    ip virtual-reassembly
    ip tcp adjust-mss 1412
    interface Dialer0
    ip address negotiated
    no ip redirects
    no ip unreachables
    no ip proxy-arp
    ip mtu 1452
    ip flow ingress
    ip nat outside
    ip virtual-reassembly
    encapsulation ppp
    dialer pool 1
    dialer-group 1
    ppp authentication chap pap callin
    ppp chap hostname XXXXXXXXXXXXX
    ppp chap password 7 XXXXXXXXXXXXXXXX
    ppp pap sent-username XXXXXXXXXXXXXX password 7 XXXXXXXXXXX
    no cdp enable
    ip forward-protocol nd
    ip http server
    ip http authentication local
    ip http secure-server
    ip http timeout-policy idle 60 life 86400 requests 10000
    ip nat inside source static tcp 192.168.0.25 80 interface Dialer0 80
    ip nat inside source list 1 interface Dialer0 overload
    ip route 0.0.0.0 0.0.0.0 Dialer0
    logging trap debugging
    access-list 1 remark INSIDE_IF=Vlan1
    access-list 1 remark CCP_ACL Category=2
    access-list 1 permit 192.168.0.0 0.0.0.255
    dialer-list 1 protocol ip permit
    no cdp run
    control-plane
    banner exec ^C
    % Password expiration warning.
    Cisco Configuration Professional (Cisco CP) is installed on this device
    and it provides the default username "cisco" for  one-time use. If you have
    already used the username "cisco" to login to the router and your IOS image
    supports the "one-time" user option, then this username has already expired.
    You will not be able to login to the router with this username after you exit
    this session.
    It is strongly suggested that you create a new username with a privilege level
    of 15 using the following command.
    username <myuser> privilege 15 secret 0 <mypassword>
    Replace <myuser> and <mypassword> with the username and password you
    want to use.
    ^C
    banner login ^CAuthorized access only!
    Disconnect IMMEDIATELY if you are not an authorized user!^C
    line con 0
    login local
    no modem enable
    transport output telnet
    line aux 0
    login local
    transport output telnet
    line 2
    no activation-character
    no exec
    transport preferred none
    transport input all
    line vty 0 4
    privilege level 15
    login local
    transport input telnet ssh
    scheduler max-task-time 5000
    scheduler allocate 4000 1000
    scheduler interval 500
    end
    Any help would be appreciated

    Hello,
    i have the same problem with router CISCO861W-GN-E-K9. Version 12.4(22r)YB5, RELEASE SOFTWARE (fc1)
    Can someone help?
    Thank you.
    Here is my config for internal AP and router.

Maybe you are looking for