IPv6 support on ME 3400 Series?

Hello,
I'm looking into deploying a couple ME-3400G-12CS-A metro ethernet switches in our network. All the features listed on data sheet look great, however IPv6 support appears to be missing.
Assuming the ME 3400 series does not support IPv6, will IPv6 support be available in the future through a mean of software upgrade for ME 3400's product roadmap? Or will enablement of IPv6 require complete replacement of ME3400 series products with something else (i.e. for example, Cat3550's hardware TCAM could not support IPv6, thus cat3560 is the right platform to upgrade into for v6 support).
Thanks in advance for any suggestion that you can provide.

ME 3400 does not support IPv6 currently in software. But there is no such limitation in ME 3400 hardware. So you can expect that IPv6 may be supported in near future.

Similar Messages

IPv6 support for sx300 series?

Hi all,
I'm wondering if we are going to be seeing some better IPv6 support on these switches? Maybe even some static IPv6 routing?
Thanks.

Apparently it's on the roadmap for 2012, so with a bit of luck we'll see it some time then:
https://supportforums.cisco.com/thread/2113913
Oh, whoops, it's already 2013!
Seriously though, an update on where this feature request got to would be appreciated - is there anyone at Cisco who can give us an update?. Perhaps there's a version 8.0 of software for these phones about to be released with new support or something? v7 has been out there a while now.

No sound on Intel HD Audio (3400 series 5)

$ lspci | grep -i audio
00:1b.0 Audio device: Intel Corporation 5 Series/3400 Series Chipset High Definition Audio (rev 06)
$ lsmod | grep '^snd_' | column -t
snd_pcm_oss 38914 0
snd_mixer_oss 15315 1 snd_pcm_oss
snd_hda_codec_hdmi 22784 1
snd_hda_codec_conexant 42084 1
snd_hda_intel 22186 0
snd_hda_codec 77703 3 snd_hda_codec_hdmi,snd_hda_codec_conexant,snd_hda_intel
snd_hwdep 6342 1 snd_hda_codec
snd_pcm 73736 4 snd_pcm_oss,snd_hda_codec_hdmi,snd_hda_intel,snd_hda_codec
snd_timer 19488 1 snd_pcm
snd_page_alloc 7161 2 snd_hda_intel,snd_pcm
alsaconf complains that no "No supported PnP or PCI card found"
This is a shiny new Lenovo X201 total lack of sound is completely killing the Arch experience. Any pointers/advice is very appreciated
regards
srp

lostone wrote:I cant seem to find the one for hp pavilion dv7 1183cl
It's not important, I've never found nowhere stated that dell M2400 uses dell-m4-2 but I've tried and it worked...
Start with option snd_hda_intel model=hp-bpc-d7000 and reboot your computer. If it doesn't work, try with some other option from the list bellow... Good luck!
ALC262
47 ======
48    fujitsu Fujitsu Laptop
49    hp-bpc HP xw4400/6400/8400/9400 laptops
50    hp-bpc-d7000 HP BPC D7000
51    hp-tc-t5735 HP Thin Client T5735
52    hp-rp5700 HP RP5700
53    benq Benq ED8
54    benq-t31 Benq T31
55    hippo Hippo (ATI) with jack detection, Sony UX-90s
56    hippo_1 Hippo (Benq) with jack detection
57    sony-assamd Sony ASSAMD
58    toshiba-s06 Toshiba S06
59    toshiba-rx1 Toshiba RX1
60    tyan Tyan Thunder n6650W (S2915-E)
61    ultra Samsung Q1 Ultra Vista model
62    lenovo-3000 Lenovo 3000 y410
63    nec NEC Versa S9100
64    basic fixed pin assignment w/o SPDIF
65    auto auto-config reading BIOS (default)

Win7 and ATI hd 3400 series driver problem

Hi guys
i have installed win7 on my T400. generally there is not driver problem. but in device manager window there is a '!' on ATI mobility Radeon hd 3400 Series. i have downloaded ATI Display Driver for Windows 7 32bit and 64bit from http://www-307.ibm.com/pc/support/site.wss/WIN7-BETA.html#m8xdiscrete but there is not any change.
1-is it a serious problem?
2-how can i solve this problem?
best regards
Solved!
Go to Solution.

Since your system shows two display adapters, you do have switchable graphics. Deinstall the ATI driver and install the Switchable Graphics driver. This package contains drivers for both cards and allows them to cooperate.
Lenovo Premium Business Partner
X1 Carbon Touch | i7-3667U | 8Gb | 256Gb | HD 4000 | 14HD+ | WWAN | W8.1 Pro RTM x64 |

HP PRO 3400 Series desktop won't boot CPU fan starts and stops , no video, no beeps

I have the above computer with an i3-2125 CPU, Windows 7 Home Premium 64 bit, and a 300GB Seagate Hard drive. I've had it for about 2 years and been working fine. It started acting up about 2 months ago. It would lose the date and time. I checked the battery, and it was OK, so I kept using the computer. Then on 9/15/2014 it hung on "Starting Windows", I did the following:
1. Ran the built in HP diagnostic on hard drive and memory and they both passed.
2. Tried to go to last known good configuration and nothing happened.
3. Noticed the date and time were off, replaced the battery, nothing changed.
4. Tried another hard drive from another HP PRO 3400 Series and it would boot up but could not set date in bios.
5. Tried all kinds of things but could not set date in bios.
      a. Bios date read 48/00/0048 after removing and replacing battery.
      b, Tried to reset date to 9/16/2914 and it gets 56/00/0051
6. Then it wouldn't boot at all.   So now when you turn on the power, the CPU fan starts and runs for about 1 second, then shuts off for 4 seconds, then starts and runs for another 1 sec and it does this continuously. There is  no video and no beeps and no difference when all memory is removed.
7. I removed the power supply, and checked voltages. It appears to be OK.
8. I removed the motherboard, and inspected it- saw nothing obvious.
9. I connected the power supply to the motherboard with nothing else connected to the motherboard, and I get the same thing. CPU fan starts then stops continuously, no video no beeps.
10. I am thinking it is the Motherboard, but I sure could use some suggestions as to what to do next.
Thanks
Maxgle from CA

Maxgle, welcome to the forum.
I believe that you would get more responses to your problem if you start a thread here. They are the members who know your computer best.
Please click the "Thumbs up + button" if I have helped you and click "Accept as Solution" if your problem is solved.
Signature:
HP TouchPad - 1.2 GHz; 1 GB memory; 32 GB storage; WebOS/CyanogenMod 11(Kit Kat)
HP 10 Plus; Android-Kit Kat; 1.0 GHz Allwinner A31 ARM Cortex A7 Quad Core Processor ; 2GB RAM Memory Long: 2 GB DDR3L SDRAM (1600MHz); 16GB disable eMMC 16GB v4.51
HP Omen; i7-4710QH; 8 GB memory; 256 GB San Disk SSD; Win 8.1
HP Photosmart 7520 AIO
++++++++++++++++++
**Click the Thumbs Up+ to say 'Thanks' and the 'Accept as Solution' if I have solved your problem.**
Intelligence is God given; Wisdom is the sum of our mistakes!
I am not an HP employee.

IPv6 support in JDMK 4.2

Hi,
We are working on enhancing our product to support IPv6. Currently we are using JDMK 4.2 with JDK 1.5. Wanted to know if there is any information about JDMK 4.2 support for IPv6?
1) Does it support binding using IPv6 interface
2) Can it accept SNMP request over IPv6 and send traps over IPv6 interface?
Or should we migrate our application to newer version of JDMK?
Regards
-murali

There is IPv6 support in the ASA version 8.2.
We just posted an IPv6 Quick Start guide at https://supportforums.cisco.com/docs/DOC-15973 and would appreciate feedback on it.
The Public Servers features is a NAT/PAT feature. The good news is that the immense address space of IPv6 eliminates the need for NAT, you can just use use access lists to set up your policy.

IPv6 support in IOS

hi,
we have a Cisco 2851 router and bought the following IOS::
System image file is "flash:c2800nm-spservicesk9-mz.124-25d.bin"
Cisco IOS Software, 2800 Software (C2800NM-SPSERVICESK9-M), Version 12.4(25d), RELEASE SOFTWARE (fc1)
I thought this version was supposed to have IPv6 support?
TEST(config)#ipv6 unicast-routing
^
% Invalid input detected at '^' marker.
TEST(config)#
which IOS should we buy?
regards,
Paal

I think you need the IOS advanced IP Services.
Cheers,
Eehab
- Please rate the asnwers you find useful.

Question about Oracle10g Net Services'IPv6 Support

I'm working in a network group which is studying the IPv6.Recently I installed oracle10g in the RedHat Linux-9(kernel-2.4.22,which supported the IPv4/IPv6 dual mode),but I can't configure the oracle10g in IPv6.
I tried every method to find the solution,including read the oracle10g document,use the google,ask the support service,but there was no answer.And I can't login into the metlink to ask question because I didn't have the CSI number.
So who can give me some advice about the configuration.Thank you very muck!

I read the document before it was taken down a couple weeks ago. It said that IPv6 support would be introduced with Oracle11g and not back ported.
Kind regards,
Russ Cannon

What is the maximum number of ARP entries (IPv4) and ND entries (IPv6) supported in our controllers?

Q: What is the maximum number of ARP entries (IPv4) and ND entries (IPv6) supported in Aruba controllers?
A: The maximum number of static ARP entries supported is about 2048 for M3/72xx/70xx platforms.
The maximum number of static ARP entries supported is about 128 for 6xx platforms.
The maximum number of static ND entries supported is about 2048 for M3/72xx/70xx platforms.
The maximum number of static ND entries supported is about 128 for 6xx platforms.

a)It depends upon software level. b) 16,000 per card, With release 9.3:
60K Connections Support on BXM-E—Provides the ability to support a maximum of 60K per card for VSI applications for the BPX 8600, for example, PNNI or MPLS, used on enhanced BXM-E cards.

E4200 IPV6 support (and the removal of it)

Dear Linksys representatives,
Could you please provide some detail on why IPv6 was available in the first builds of the router but then got removed in later firmware versions and the official lecture is that IPv6 is not being supported at all.
I've had a nice little chat with one of your representatives and they could not clarify this at all. Actually, they say no Linksys devices EVER supported IPv6 period, which does not seem to be entirely true. Saw that 1.0.00 (build 13) for the e4200 actaully has IPv6 support in it and the current build has not.
Could you also make a sticky post about IPv6 support on all Linksys devices with wether they will be supporting it in the future or not? Depending on the outcome to this question I'm deciding to return my Linksys device or not, since I actually need to have IPv6 support for development of new soft- and hardware.
Kind regards,
Michel
ps: happy IPv6 day!
http://www.worldipv6day.org/

The E4200v1 and E4200v2 both support IPv6 in the latest firmware. Do you still have a problem? See also: http://home.cisco.com/ipv6 for a list of routers and the test suites that they have past.
All future home routers are expected to have IPv6.

Oracle Lite Support for Nokia E-Series (Symbian OS 9.2)

Are there any plans to support the Nokia Enterprise Series of handsets running the Symbian OS 9.2 in the near future (i.e. E60/E61/E70).
Thanks.

Ciao
all Nokia 3rd edition have Flash Lite 1.1 embedded so they
currently do not support FL2.
Nokia will release FL2 on the 3rd edition feature pack
1models, probably next year.
Alessandro

LMS prime 4.2.5 IPV6 support

I'm attempting to configure LMS 4.2.5 to perform IPV6 addressing for polling and device management I need advice on how to proceed as I see very little documentation and I'm not seeing any options in the configuration web GUI

I've not had a chance to exercise the features, but there's a table in Chapter 1 of the LMS 4.2 Admin Guide in the section "IPv6 Support In LMS" that outlines exactly where you can use IPv6 device addresses across the various LMS functions.

IPv6 Support on RV042

Hi,
Any update is planified for add IPv6 support to Cisco Small Business RV042 Router ? My ISP, My modem and server software have IPv6 support but not the RV042

Thanks for participating in the Small Business Support Community. Your feedback is important to us and we do pay attention. IPv6 will be supported on an upcoming RV042 hardware version 3. IPv6 support is not forthcoming for earlier hardware versions.
Please keep the feedback coming. It's how we improve.
Thanks,
Stephanie Reaves
Cisco Small Business Technology Group

IPv6 on CIsco 7200 VXR series router

Dear Friends,
I want to know, whether cisco 7200vxr router support ipv6? I want to use both ipv4 and ipv6. In that case whats about the performance.
Do i need IOS upgradation to acheive this implementation.

Hi -
Our s/w development group is in the process of implementing ipv6 support in our products, and would like to use our Cisco 2650XM running ITP s/w for ipv6 interoperability tests.
However, it appears that ipv6 is not supported in this s/w version:
ITP1#sh version
Cisco IOS Software, C2600 Software (C2600-ITPK9-M), Version 12.4(15)SW2, RELEASE SOFTWARE (fc3)
Technical Support: http://www.cisco.com/techsupport
Copyright (c) 1986-2008 by Cisco Systems, Inc.
Compiled Tue 23-Sep-08 19:48 by prod_rel_team
ROM: System Bootstrap, Version 12.2(7r) [cmong 7r], RELEASE SOFTWARE (fc1)
ITP1#config
Configuring from terminal, memory, or network [terminal]?
Enter configuration commands, one per line. End with CNTL/Z.
ITP1(config)#ipv6 ?
% Unrecognized command
My question is: Can I use this s/w version on the 2650XM in an ipv6 network? Do I need to upgrade the s/w?
Thanks,
Matt

2620 IPV6 support

                   Hi Everyone,
On 2620 Router is there any ios version that supports IPV6 ospf under interface config as shown below
(config)#int fastEthernet 1
(config-if)#ipv?
ipv6
1(config-if)#ipv6 ?
IPv6 interface subcommands:
    ospf                OSPF interface commands
    sh ver
Cisco Internetwork Operating System Software
IOS (tm) C2600 Software (C2600-A3JS-M), Version 12.2(26c), RELEASE SOFTWARE (fc1)
Copyright (c) 1986-2007 by cisco Systems, Inc.
Compiled Mon 30-Jul-07 18:03 by ccai
Image text-base: 0x8000808C, data-base: 0x815F24E0
ROM: System Bootstrap, Version 11.3(2)XA4, RELEASE SOFTWARE (fc1)
R2 uptime is 38 minutes
System returned to ROM by reload
System image file is "flash:c2600-a3js-mz.122-26c.bin"
cisco 2620 (MPC860) processor (revision 0x00) with 61440K/4096K bytes of memory.
Processor board ID JAD0650058C (300495423)
M860 processor: part number 0, mask 49
Bridging software.
X.25 software, Version 3.0.0.
SuperLAT software (copyright 1990 by Meridian Technology Corp).
TN3270 Emulation software.
2 FastEthernet/IEEE 802.3 interface(s)
2 Serial network interface(s)
32K bytes of non-volatile configuration memory.
16384K bytes of processor board System flash (Read/Write)
Configuration register is 0x2102
Regards
Mahesh

Hi Mahesh,
It appears that you already have IPv6 support (under the interface) with the current version of the IOS. The IOS should be the same for 2620 and 2621 routers.
HTH

IPv6 support on ME 3400 Series?

Similar Messages

Maybe you are looking for