Ipx configuration for router 2800

please help me to have ipx configuration for router 2800 work with novel ver4 server.

please help me to have ipx configuration for router 2800 work with novel ver 4 server.

Similar Messages

Optimal configuration for Cisco E3000 Router

Hi All,
Following are the details of my current home network setup, I would like to hear more recommendations and drawbacks of this setup.
ISP has provided with a Cisco DPC3825 DOCSIS 3.0 Gateway which has 4 Ethernet ports and a wireless networking but only 2.4 GHz.. This router is connected to the cable CPE box to internet. I have enabled the Firewall features of this router and disabled the Wireless network. This has also the DHCP server running.
The Second router is a Cisco E3000 which supports 2.4 GHz / GHz wireless networking. Connection to gateway is made via the 1st Ethernet port of gateway and then to the Internet port of E3000 router. I have connected my wireless devices to E3000 with GHz wifi lan. This router also has the firewall activated and DHCP server running as well.
Both routers have WEP2 Personal / AES security configured. Currently these two devices are on two different IP ranges ..etc gateway is 192.168.0.1 and e3000 is 192.168.1.1.
The E3000 is primarily configured for my online video for TV (Panasonic Vireacast). Please let me know if this is the best configuration or any other possible options.
Thanks,
RG

This configuration is called LAN to WAN configuration and this is the best configuration considering that you want to behave both the router as a router.
Because the other confiuration would be LAN to LAN then you can only use 1 router as a router and 2nd router as a switch.
http://www6.nohold.net/Cisco2/ukp.aspx?vw=1&docid=529c188bc0ee4f7da79ffc22f2be33ec_4579.xml&pid=80&r...
The first configuration in the article is is LAN to LAN, scroll down the window for LAN to WAN configuration.

Cisco works LMS 3.0.1 does not archiever configuration for cisco 7201 router

Hi All,
We have Cisco works LMS 3.0.1 and it does not archiever configuration for cisco 7201 router.
Any help would be appriciated.
Thanks in advance
Samir

Hi,
*** Device Details for d0151-100 ***
Protocol ==> Unknown / Not Applicable
Selected Protocols with order ==> TFTP,SSH,HTTPS
Execution Result:
Unable to get results of job execution for device. Retry the job after increasing the job result wait time using the option:Resource Manager Essentials -> Admin -> Config Mgmt -> Archive Mgmt ->Fetch Settings
This is the error while doing syn archieve.
I am not sure about Rtr7000 version but we have latest Rtr7000.
Waiting for your kind reply.
Samir

Configuring Cisco Router for use with Syslog Server

Configuring Cisco Router for use with Syslog Server:
Does anyone know of a good doc for this?
-Ashley

Start with that one: http://security-planet.de/wp-content/uploads/2008/12/logging-ios.pdf
And if you need more informations, just ask what you want to achieve.
Don't stop after you've improved your network! Improve the world by lending money to the working poor:
http://www.kiva.org/invitedby/karsteni

Please help me in configuring a Cisco 2800 series router!

Hi! I have to configure a new router with a static route. No routing protocol will be used. I just have to set default route on it and NAT. My senior Network Engineer has asked me to configure this router. There's an apartment where our Overseas employees stay, earlier this apartment had a broadband connection which was further divided through the APs(Cisco Wireless Access Points) and made usable to around 20 users. Now, they have bought in their own lease line and I have to configure this router. We just have to connect it with the ISP using Ethernet (not serial link). I would be so so grateful if you can just type in complete configuration for this. Thanks a ton in advance!

Hi There,
Thanks for your great help!
Below is the final template which my NE provided me:
Now I have to configure this router and then further need to connect various workstations with the same network. Please let me know what needs to be done further.
Thanks!
Configuration:::
service timestamps debug datetime msec
service timestamps log datetime msec
service password-encryption
ip domain-name CVT.net
logging buffered 128000 informational
logging console errors
logging monitor notifications
no aaa new-model
clock timezone IST 5 30
ip cef
no ip domain lookup
username aptadmin secret
enable secret
crypto key generate rsa
ip ssh time-out 60
ip ssh authentication-retries 2
ip ssh version 2
service dhcp
ip dhcp pool LAN-POOL
network 192.168.1.0 255.255.255.0
default-router 192.168.1.1
dns-server 8.8.8.8 4.2.2.2
domain-name CVT.net
lease 1
interface FastEthernet0/0
description *********Spectranet WAN*********
ip address x.x.x.x 255.255.255.252
load-interval 30
duplex full
speed 100
ntp disable
no cdp enable
interface FastEthernet0/1
description Connect to LAN
ip address 192.168.1.0 255.255.255.0
no ip redirects
duplex auto
speed auto
ntp disable
ip forward-protocol nd
no ip http server
no ip https server
control-plane
banner exec $
Network Provided by CVT
This system is restricted to authorized individuals. Unauthorized access is a
criminal violation of the law and is subject to prosecution. Please disconnect
if you are not an authorized individual. Otherwise, you will be prosecuted
to the full extent of State and Federal law.
All connections and changes are logged.
************** Warning - Warning - Warning **************
$
banner login $
Authorized Associates only! Please disconnect your connection if
you are not an authorized Associate. Otherwise, you will be
prosecuted to the full extent of State and Federal law.
All connections and changes are logged.
$
line con 0
exec-timeout 15 0
password 7
login local
line aux 0
exec-timeout 15 0
password 7 C@pt
login local
line vty 0 4
access-class 50 in
exec-timeout 5 0
login local
transport preferred ssh
transport input ssh
line vty 5 15
access-class 50 in
exec-timeout 5 0
login local
transport preferred ssh
transport input ssh
end

6602: Want to route a dedicated DIO (0-7) Line configured for output to a RTSI line

PXI-6602: I want to use a dedicated DIO (0-7) line configured for output to trigger all 8 counters on the 6602 card. The counters are configured for two-signal-edge-separation measurement. I Have tried to use Route-Signal.vi to route PFIn (0-7) to RTSI bus with no luck.

You should be able to trigger counters on the 6602 using the Digital Lines DIO (0-7).
Use the Set Attribute VI and set the attribute value type to Enabled and attribute ID to Start Trigger.
Wire the output of Set Attribute Task ID to the Task ID input of the Route Signal VI. Select the start trigger for the Signal Name input, PFI n for Signal Source input and PFI line Number for Signal Source Line Number input. Try this and see if this works.
Regards,
Bharat Sandhu
Applications Engineering
National Instruments."
Penny

Ea 2700 has anyone been able to configure this router for trapping on a port

ea 2700 has anyone been able to configure this router for trapping on a port....if so can you help us?

Hi,
What do you mean by trapping on a port? Is it the same as port forwarding? The following link might help:
Setting up single Port Forwarding on Linksys Wi-Fi Routers and Smart Wi-Fi Routers

How do I Configure my Router to forward incoming data for port x ???

How do I configure my router to forward incoming data for port whatever?
I need this for my video games.

Depending on which router you have look under Gaming and Applications or system management for a Forwarding tab. From there you select (or create) the port needed for your game with the IP address to the PC with the games you are using. You may also have to configure Port Triggering for that game/port range/and IP to the hosting PC.
Richard Aichner (Ikester)

Related to vmic2-2mft-g703 module on Router 2800

I have purchased the vmic2-2mft-g703 for CISCO 2800 series router and want to know that can I configure this card two interfaces act as a simple data interfaces like router inbuilt ethernet interfaces? If yes then how? Please help me.

Hello Ganesh,
try to see if
conf t
controller e1 0/2/0
is supported it it looks like you need to go this way
see
http://www.cisco.com/en/US/products/hw/modules/ps2617/products_configuration_example09186a008052c920.shtml
if so you need to configure a channel-group
controller e1 0/2/0
no shut
channel-group 0 unframed
a serial interface is created
serial 0/2/0:0
verify with your provider if you need an unframed or all timeslots in a group config
Hope to help
Giuseppe

How do I configure for port forwarding?

I just relpaced my CISCO E3000 wireless router with an Apple Airport Extreme and need to set up port forwarding. I find the Airport Utility confusing and very limited in capabilities. How do I configure the router for Port Forwarding?

Here's a document that you can follow: https://discussions.apple.com/docs/DOC-3415
However, I ran into an issue with setting this up and had to do a work-around: Custom Port Forwarding Config Not Working

Upgrading from Exchange 2003 Bridgehead servers to Exchange 2010 Transport Hub servers for routing SMTP only

Our company moved from on-premises Exchange 2003 to Office365 and only have 4 Exchange 2003 servers on-prem that we use for Routing email from application servers to Office365. We need to migrate these servers to Exchange 2010 then to Exchange 2013 and
only route email only. Is it possible to upgrade to Exchange 2010 by installing the transport Hub & Mailbox server options only? Our OAB and EWS services come from the CAS servers located on Office365 so we should not need a CAS server to set up Transport
rules or route mail would we? Any assistance with this would be greatly appreciated! - Thanks, DWB
Dave

Since it is not internet facing we will not have to worry about configuring an Internet Domain Name when installing the first server, correct? in my planning I was going to
install the Exchange 2010 CAS/Mailbox/Transport Hub roles on one server, then upgrade it to Exchange 2013. Once this is completed I'll then install the 2 mailbox role servers in one Datacenter, and 3 more in our DRP DC. If something happens to the
primary Datacenter I would want it to fail over to the other site. For this I would have to install another CAS/mailbox server in the secondary DC. Would this plan sound about right? Since we moved to Office365 in 2010 I have not had a chance to deal with
actual servers except for the Exchange 2003 servers we still have on-premises. Each of these are located in 4 Regional offices along with single Windows 2008 R2 servers using only the IIS SMTP service for routing mail from on-prem application servers
and print/scanners which email back to the users. The plan is to move to a routing system which will provide both MTA and redundancy if one has an issue.
Dave

QOS for Routing updates, LDP, etc

Hi.
We are needing to provide QOS to our voice traffic and we were thinking in configure Precedence 7 to this traffic. The traffic goes through an MPLS Network of 7600 as PE and 12000 as P. Can we configure the routing traffic, LDP and other signaling generated on the routers to use a service class as if the traffic were marked as precedence 6? how can we mark this traffic as precedence 6 changing the default? Is 7 the default value?
Thanks

Hello Pedro,
I did some tests years ago
all routing protocols including OSPF, LDP and BGP uses precedence 6 with the execption of some RSVP-TE messages that are sent out with precedence 0.
Precedence 7 is not used in protocol messages.
However, the recommended value for voip bearer packets is precedence 5 that fits with DSCP EF Expedite Forwarding.
Using precedence 7 is not recommended but you can and you don't need to remark signalling packets.
I would use precedence 5 and I did in the past and also now we use it for voip.
Hope to help
Giuseppe

ESB: Is it possible to create custom WSDL for routing service?

Hello all!
I have an unchangeable requirement in my project - ESB routing services must confom to WSDL specifications that are already used before we started this integration project.
For example, we have to implement not only the same logical part of WSDL description:
<message name="AuthorisationRequestSoapIn">
<part name="AuthorisationRequest" element="tns:AuthorisationRequest"/>
</message>
<message name="AuthorisationRequestResponseSoapOut">
<part name="AuthorisationRequestResponse" element="tns:AuthorisationRequestResponse"/>
</message>
<portType name="OnlineServicesSoap">
<operation name="AuthorisationRequest">
<input message="tns:AuthorisationRequestSoapIn"/>
<output message="tns:AuthorisationRequestResponseSoapOut"/>
</operation>
</portType>
but the binding and service sections must conform to WSDL document too:
<binding name="OnlineServicesSoapBinding" type="tns:OnlineServicesSoap">
<soap:binding transport="http://schemas.xmlsoap.org/soap/http"/>
<operation name="AuthorisationRequest">
<soap:operation style="document" soapAction="AuthorisationRequest"/>
<input>
<soap:body use="literal" namespace="http://..../OnlineServices"/>
</input>
<output>
<soap:body use="literal" namespace="http://..../OnlineServices"/>
</output>
</operation>
</binding>
<service name="OnlineServicesSoapService">
<port name="OnlineServicesSoapPort" binding="tns:OnlineServicesSoapBinding">
<soap:address location="....."/>
</port>
</service>
And after registration of ESB routing service I've got the following service description (I ommit esb bindings and logical part here, it's ok with messages and portTypes):
<binding name="__soap_OnlineServicesSoapService_OnlineServicesSoap" type="import:OnlineServicesSoap">
<soap:binding xmlns:soap="http://schemas.xmlsoap.org/wsdl/soap/" style="document" transport="http://schemas.xmlsoap.org/soap/http"/>
<operation name="AuthorisationRequest">
<soap:operation xmlns:soap="http://schemas.xmlsoap.org/wsdl/soap/" style="document" soapAction="AuthorisationRequest"/>
<input>
<soap:body xmlns:soap="http://schemas.xmlsoap.org/wsdl/soap/" use="literal"/>
</input>
<output>
<soap:body xmlns:soap="http://schemas.xmlsoap.org/wsdl/soap/" use="literal"/>
</output>
</operation>
</binding>
<service name="ESB_OnlineServicesSoapService_Service">
<port name="__soap_OnlineServicesSoapService_OnlineServicesSoap" binding="tns:__soap_OnlineServicesSoapService_OnlineServicesSoap">
<soap:address xmlns:soap="http://schemas.xmlsoap.org/wsdl/soap/" location="http://..../event/DefaultSystem/OnlineServicesSoapService"/>
</port>
</service>
How can I change WSDL that is generated for routing services? Is it possible to change the names of port and binding element?
Thanks in advance,
Oleg Olenin

So, no docs, no answers, no life :) - I have only one way to get the answers:
oracle.tip.esb.configuration.util.WSDLGenerator.addSOAPBindings():
binding.setQName(new QName(targetNamespace, WSDLConstants.generateSOAPPortName(service.getName(),portType.getQName().getLocalPart())));
oracle.tip.esb.configuration.util.WSDLConstants:
public static final String generateSOAPPortName(String service, String operation)
return "__soap_" + service + "_" + operation;
So it is not possible to change the names of SOAP binding and port.
And I guess there is no way to change WSDL that is generated for routing services.

Re-Org/Update Program for Route determination

Hi
does anyone know if there is a Re-org / Update program for Routes ?
I have added new routes, against Shipping conditions from NO and SE to many Western European Countries , and would like to update Sales orders/ deliveries with these new routes
Many thanks for your advice
Tony

Hello Tony
For the orders, if you have configured 'Define New Route Determination By Delivery Type', then route redetermination takes place during delivery creation and finds the new route. So I would say don't bother about fixing the orders.
Just ensure you have configured these 2 items in IMG:
LE/Shipping/Basic Shipping Functions/Routes/Define New Route Determination By Delivery Type,
and
LE/Shipping/Basic Shipping Functions/Routes/Define Allowed Actual Route By Proposed Route.
That leaves open deliveries which are not PGIed to be taken care of.

Minimum Configuration for SDM.

Hi I would like to know what is the minimum configuration for access by sdm my router with volares manufactured, is a 877. Greetings

Your 877 device is sufficent . Make sure you are using IOS 12.3(8)YI or 12.4(2)T or later releases .
More info:Cisco Router and Security Device Manager Introduction
http://www.cisco.com/en/US/products/sw/secursw/ps5318/tsd_products_support_series_home.html

Ipx configuration for router 2800

Similar Messages

Maybe you are looking for