IRQ help

I was checking my irq settings and I have no Irq conflick problems I dont think all are listed status of OK.But I do have three things asigned to IRQ 11.
1.Video card
2.Network card
3.USB host controller
My question is how do I change it so my video card is byitself.Could this cause problems at high fsb or would it be a issue the would cause problems all the time. Any help would be useful.
I have MSI K7N2 Delta with bios v. 5.7 . I have disabled both serrial port and parrellel ports but it doesnt move the IRQ 11 asignment at all.I do see in bios where I can do manual irq setting but when you go into options for manual setting you just have enable or disable.How do I asign my agp video card to a irq all alone?
Thanks for anyhelp

well i moved my pci either card up one slot and it did move my video card to irq 10 it shares IRQ 10 with nvidia pci system management.Should I just try other pci slots til it ends up with my video by itself.
as to the other question I did a fresh install with apic disabled. I have had trouble with the apic funtions on my abit kd7 motherboard and in abit fourms it was recommended to do a fresh install with apic disabled. When I changed to the nvidia chip set I just did a fresh install with it disabled again.Not really hip on reformating hard drive when the are no troubles.I just want to move my video card to its own irq.I know little about apic just cause issues on the abit in past.
thanks for your help guys.
One thing I am curious about, would a irq conflick cause problems at any fsb/clock setting or would raising the fsb make it worse.I have had a irq not less or equal crash error when I was tring for 430 fsb.That is why i looked into my irq settings but like I stated I have no irq problems even when I had the 3 things asigned to the irq 11.When running at lower fsb settings.I usally run 380 fsb with 5-2-2-2 ram timings.No conflicts at all.
Thanks again for your help

Similar Messages

  • Audigy 2 ZS Interfering with WIFI c

    System Specs:
    P4 .6 GHz on an Intel D845HV Board
    Audigy 2 ZS
    Linksys WMP 802.b Wireless Network Card
    Windows 2000 Professional (SP4)
    Upon installation of my sound card, the wireless network card installed next to my new sound card stopped functioning properly. When I have my sound card enabled, my internet connection becomes slow and laggy. Under these conditions, even simple tasks like downloading email from an email server become impossible. However, when I disable the sound card with the device manager in windows control panel, my wireless network card works as normal.
    I have tried installing both cards in different PCI slots (I only have 2 PCI slots availabe because one is blocked by my video card cooler), updating drivers, and creative customer support, but nothing seems to make my wireless network card work properly while my sound card is enabled
    Any suggestions are greatly appreciated and thx ahead of time

    Ok, Customer Support is leaning towards a resource problem and has suggested that I change the IRQ of my soundcard; however, I am using Windows 2000 with ACPI mode. When I looked at the Intel webpage (Intel is the maker of my motherboard), I found this:
    "In Windows* 2000, some or all of the devices on your ACPI motherboard may be listed on the Resources tab in Device Manager as using the same IRQ (IRQ 9). You cannot change the IRQ setting because the setting is unavailable. This occurs because Windows* 2000 takes advantage of the ACPI features of the motherboard, including advanced PCI sharing. IRQ 9 is used by the PCI bus for IRQ steering. This feature lets you add more devices without generating IRQ conflicts."
    While my sound card and WIFI card are not on the same IRQ (WIFI IRQ is 22, and Sound Card IRQ is 23) and the IRQ is clearly not 9 like this excerpt exemplifies, it leads me to believe that I cannot manually assign an IRQ with ACPI enabled.
    Again, this seems to be a problem only in Windows 2K, so would a switch to Windows XP fix this situation? Also, if they are not on the same IRQ right now, how would changing the IRQs help anything in this situation. Any feedback is welcome.

  • Screwy IRQ's Help!!

    Need help trying to install XP on a athlon , k7t turbo limited edition mother board , 1 stick 128 mb 133mhz , 40 gig ata100 "only can run a 66 cable cause Im poor" 32 mb radeon pci . I also dont know how many mhz I got, its running at 1.3 but the overclocking options dont look right either. I would take off the cooler and find out but i dont got any of that compound stuff.
    Just trying to through a cheap system together and never thought id run into so many problems. When it boots up I look at the driver list and 3 or 4 devices are all on a same IRQ "just dont look right" It doesnt seem to be a problem but then when I try to install windows it gives me the IRQ_IS_REALLY_FUCKED up message. Now Ive tried Everything possible in BIOS and now im going through this forum reading about similar problems and I found one solution that is working now as im typing this. I had to disable the cpu's cache " This did not fix the irq problem but it did let me get by the blue screen with the irq problem on it. Besides that ive also tried putting my pci cards in differnt slots and Ive read the manual to the board maybe 10 times over and tried just about all the jumper settings only one that helped is when i messed around with the RAID. Now im wondering about a couple of things i hope you can answer.
    1. cpu's temp was running in low 60's
              ? could it be the cooler
    2. Couldnt install new bios cause my a: was not letting me copy files in dos to the ramdrive.
              ?If its that how do i fix it
    3 once xp is done installing will it be ok if i enable cpu caching ???
    4 and how can i figure out what kinda cpu i got without taking fan and cooler off.
    Id apreciate any replies or messages ill be on icq and aim trying to fix this crap.
     "Ive never had a prob like this before thats taken me all night to fix please someone relieve me LET ME SLEEP"
    sorry about spelling to just noticed a little tired.

    did you try resetting the bios to bios defaults?  IRQ errors are usually due to driver or bad hardware.  Try running the cpu/ram at 100mhz to see if that stabilizes the system.

  • Nic transfers out but can't receive packets.  Need (IRQ?) help.

    The other day, I was having trouble with an Intel board with an on board Realtek nic. (see http://forum.java.sun.com/thread.jspa?threadID=5282653&tstart=0)
    I'm having a similar problem now with a Gigabyte 8i865GME-775 with an Intel 8550 onboard nic.
    The interface is plumbed, up, running and properly configured as iprb0 once I added the appropriate line in /etc/driver_aliases which was irpd "pci8086,1051"
    I did some snooping around in logs and I noticed that packets are going out but there are no packets coming in according to kstat iprd.
    I tried apci_user_options = 0x2 as well as 0x4, 0x8 and 0. Didn't seem to make a difference. Is there something else besides just rebooting to do? I also tried the two set pcplusmp:apic_forceload = -1 and set pcplusmp:apic_use_apci = 0 separately without any luck.
    I administer the machines I use to test and develop on so my administrative talents are obviously lacking and I'm in need of help with this.
    There seems to be a shared resource conflict indicated by this line in dmesg
    pcplusmp: [ID 637496 kern.info] pcplusmp: pci8086,1051 (iprb) instance 0 vector 0x14 ioapic0x2 intin 0x14 is bound to cpu 1     
    The first time I saw it I was pretty sure it was cpu0 with the same vector.
    According to the POST messages, the IRQ assigned to the nic card is 10, which doesn't seem to conflict with any of the other pci devices listed at that time. Is there a way to resolve this conflict from within Solaris? Or at least a way to view the currently assigned IRQ addresses? What's the relationship between vectors and irq's?
    I'm going to disable some of the devices that are not needed to see if that helps. But I didn't find any way to change the irq of the nic or the cpu in this Award Bios.
    There are a lot of great cutting edge features in Solaris 10, but these types of problems seem to have been plaguing people since at least 2003 from what I've seen. The last time I even worried about IRQ's, Intell processors came in two flavors SX and DX, and 9600bps was really fast. This seems to be a problem with the way Solaris 10's PnP code and not with the drivers.
    Is there anything else that can be done to get this resolved?

    Had to post this first thing in the morning because I'm all confused.
    First, mother board is actually GA-8i865GME-775-RH. The onboard nic is EP82562G chip (10/100Mbit) which I believe is also referenced as just 82562G by Intel.
    From prtpicl for the device I get:
    pci1458,e000 (obp-device, 70000001c4)
    :DeviceID     0x0
    :UnitAddress     1
    :device_id     0x1051
    :vendor-id     0x8086
    :revision-id     0x2
    :class-code     0x2000
    :unit-address     8
    :subsystem-id     0xe000
    :subsystem-vendor-id     0x1458
    :min-grant     0x8
    :max-latency     0x38
    :interrupts     0x1
    :devsel-speed     0x1
    :fast-back-to-back
    :power-consumption     01 00 00 00 01 00 00 00
    :model     Ethernet controller
    :compatible     (70000001cfTBL)
    | pci8086,1051.1458.e000.2 |
    | pci8086,1051.1458.e000 |
    | pci1458,e000 |
    | pci8086,1051.2 |
    | pci8086,1051 |
    | pciclass,020000 |
    | pciclass,0200 |
    :reg
    From http://www.pcidatabase.com/ I found,
    8086 is Intel
    1051 is PRO/100 VE Network Connection
    /boot/solaris/devicedb/master lists iprb when I grep for "PRO/100 VE". iprb plumbed but isn't working. From here http://blogs.sun.com/coolzephyr/date/200704 it's listed as ife
    On another Sun Blog and a couple other sites I saw the pci1458,e000 part refered to Syskonnect and the skge driver. On other's that id series was also linked to nge, rtls, rge and gani. So I'm not even sure if I'm using the correct driver. Intel no longer seems to have Solaris drivers for the Pro/100 VE chips, the link to Syskonnect is old and broken and I'm not sure what their actual product is.
    In /etc/driver_aliases and /boot/solaris/devicedb/master for pci8086,1005
    But if that's the case, why wasn't it detected during the installation?
    I tried loading the nge, rtls, rge and even e1000g drivers just in case. devfsadm failed to attach them.
    I went back to iprb. Made sure /etc/driver_aliases and /boot/solaris/devicedb/master reflected the correct pci8086,1051 location.
    iprb0 gets plumbed but "no MII link detected" still shows up on boot.
    I'm at a complete loss.

  • Brand New mobo (P6NGM) with IRQ Conflicts, PLEASE help

    I've posted multiple times in another well respected PC forum and have not resolved my issue yet. Would GREATLY appreciate assistance.
    Here's my story and attempts:
    I'm building a new PC for my parents:
    mobo: MSI P6NGM
    cpu: Pentium dual core e2200 (800fsb)
    memory: 2g DDR2
    video: Radeon 9600PRO 256MB PCI-E
    I'm having problems in Device Manager.
    the modem (Smart Link 5k Voice Modem) and something called the NVIDIA nForce System Management Controller both have a yellow-exclamation point on them and when I looked at their properties\device status says:
    Quote
    This device cannot find enough free resources that it can use (code 12).
    If you want to use this device, you will need to disable one of the other devices on this system. 
    I have all of the current drivers and latest BIOS installed (and confirmed).
    I believe it's telling me I have an IRQ conflict and when I looked at the Device Manager \ Resources by Type, it tells me that there are 3 devices on IRQ 7, 2 devices on IRQ10 (my PCI-E video card and the 56k modem), and 2 devices on IRQ11 (the NVIDIA nForce PCI System Management).
    I did a google search and tried disabling the com ports 1 & 2 (but could only find & disable com port 1)
    but this didn't improve the problem.
    I also tried un-plugging 2 front USB-2 ports from the mobo.
    no improvement there either.
    meanwhile, IRQs 2, 3, 4, 9, 14, and 15 are empty. Is there any way to assign to these?
    Please help.  I just built a dual core AMD with another MSI mobo for my daughter last month and didn't have any issues with it.

    yes, i tried switching to the other PCI slot (this mobo only has 2). no improvement
    Last night, I also tried disconnecting everything (3 USB ports connected to the mobo) and performing a fresh install of XP. I was extremely disappointed that this didn't work either.
    I also tried unistalling all of the devices on IRQ10 and rebooting with IRQ10 Reserved (so all of the devices would be assigned to something else). Then I uninstalled the modem again and enabled IRQ10, hoping that everything would have been assigned elsewhere and only the modem would be assigned to IRQ10 this time.
    NO LUCK!
    I've NEVER had so much difficulty with IRQs, and only installed 2 devices: the PCI-E video and a PCI modem.

  • Cannot install windows, starting to get really pissed off with this PLEASE HELP

    ok, i'm starting to get agitated with this.
    i cannot install windows XP, 2003, OR Longhorn on my machine.
    right now, i have the following setup:
    msi 865pe neo2 motherboard
    intel p4 3.2ghz w/HT (factory HS/Fan currently)
    1 dimm of PC3200 crucial DDR400
    30GB maxtor HD plugged into primary IDE
    pioneer dvd/cd drive as sencondary IDE
    alps 3.5" floppy drive
    antec true blue 480wt PSU
    i do the following:
    format with maxtor cd
    boot from OS cd
    start setup, reboot, continue
    the farthest i can get is 'registering components/completing installation' i either get a blue screen stop error which isnt the same everytime, or it just locks up and doesnt do anything.
    ran the memtest checker and get errors on test #4
    i had a DIMM of kingston that gave the same errors, so i RMA'd it and got another. same errors, so i RMA'd again and got a Crucial stick. same errors.
    so i RMA'd the motherboard since i figured it had to be that. and it improved from the problems i had earlier. (the problems i had before were worse before.)
    below are my BIOS settings. SOMEONE WHO KNOWS PLEASE HELP ME!
    advanced bios features:
    quick boot - enabled
    boot order - floppy, cd, HDD
    full logo - disabled
    s.m.a.r.t - enabled
    num-lock on boot - enabled
    floppy swap - disabled
    floppy seek - enabled
    save rom to HD - no
    boot to os/2 - no
    hyper threading - disabled
    mps revision - 1.4
    apic acpi sci irq - disabled
    cpu l1 & l2 cache - enabled
    bios cacheable - disabled
    c000, 32k shadow - disabled
    advanced chipset:
    dram timing...
    configure by spd - enabled
    (i dont know what to set timing to, nothing anyone has since said helps)
    integrated perfs:
    usb controller - enabled (same errors if its disabled too so its not USB)
    usb device legacy support - disabled
    on chip IDE:
    operate mode - legacy mode
    ata config - pata only
    sata keep enabled - yes (for sata drive i have, error either way)
    pata channel selection - both
    onboard ethernet, 1394, prmoise ide and audio all DISABLED
    pc healt status:
    cpu - 49°C/120°F (idle sitting in bios)
    system temp - 28°C/82ºF
    cpu fan - 2678rpm
    nb fan speed - 6490rpm
    vcore - 1.456 up to 1.502
    3.3v - 3.232v
    +5.0v - 5.003v
    +12v - 11.680v
    -12v - -11.743v
    -5.0v - -4.826v
    battery - 2.896v
    +5V SB - 4.945
    freq/voltage control
    Dynamic OC - disabled
    cpu ratio locked
    dram freq - auto
    spread spectrum - enabled
    cpu bus clock - 200
    ddr clock (grayed out) - 400
    adjust agp/pci - 66.66/33.33
    cpu vcore adjust - no
    cpu vcore (grayed out) - 1.5500v
    ddr power voltage - 2.65v
    agp power voltage - 1.50v
    SOMEONE PLEASE HELP ME!!!!!
    i'm running out of time, money, patience.
    if it cant be solved i'm going to set myself on fire!

    Quote
    Originally posted by REILLY875
    Do NOT try the 250 Watt PSU!!, As "Wonk" said if you happen to Blow it, the PSU will most likely Take out the Mo-Bo with it! And maybe the CPU to, due to the Voltage Spike you would get ...I would not put to much Credence into the fact that as of now the +12V and the +3.3V Rails are reading a little low,(I say this because it is indeed a ANTEC), as this could be the Monitoring Hardware, or the Software that might be reading wrong....If I where you I would First set the Memory Timings Manually to 3-4-4-7-8, And up the DRAM (VDIMM) Voltage to 2.7 Volts, and if it still wont Load, I would Definitly try a different DIMM Slot, and Rince and Repeat .....If you dont mind me asking , Why are you running with just 1 Module?....Is it on purpose or are you saving up for More?................Sean REILLY875
    yea, i dont plan to run the 250. im gonna wait for the new 480.
    thanks for the info about ram timings as well. i havnt gotten any solid answers about what to set it to.
    even with new mobo and ram, i'm getting errors in memtest86 #4 test as i always have. i've tried different slots with same problems.
    i only have one module because i dont want to waste anymore money on a non-working system. once i get it up and running i'll add another 512.

  • MSI TI 4200 - TD8X - PC freezes while playing games.. Dx problem? Settings? HELP!

    Hi
    I bought a MSI GF4 TI-4200 TD 8x about 2 months ago, and it has been running fine 'till now...I'm having a few problems in a few games (HALO, homeworld 2), ocasionally my computer freezes completely in the middle of these games, and I have to reboot...I've tried lots of things to solve this problem, but I wasn't able to just yet...As I know these 2 games use directx 9, I was wondering if my graphics card supports or is compatible with dx9...In the manual and on the site it says dx 8.1 compatible...doesn't mention dx 9... So I'd like to know if it is compatible, and if this may be the cause for all these gaming problems...If not, I'd like to know what can I do to detect where the problem is...
    When the game crashes, a long beeping sound occurs...I think this may be relevant too...
    I've updated the SB drivers, mobo drivers, nvidia drivers (tried 45.23 and 44.03), tried changing AGP aperture size on BIOS (64 or 128),
    MSI K7N2 DELTA-L
    AMD Athlon XP 2100+
    512 MB DDR333 (Kingston)
    MSI GF4 TI 4200 - TD8X
    Creative Sound Blaster Audigy Player
    Pinnacle Studio-TV
    Realtek RTL8139/810x Family Fast Ethernet NIC
    IBM 80GB 7200 RPM HD
    Samsung DVD-ROM
    LG CD-RW
    Windows XP Professional with SP1 and fully updated.
    450w PSU
    Samtron 96B
    IRQ Settings :
    (ISA) 0 System timer
    (ISA) 1 Standard 101/102-Key or Microsoft Natural PS/2 Keyboard
    (ISA) 3 Communications Port (COM2)
    (ISA) 4 Communications Port (COM1)
    (PCI) 5 NVIDIA nForce PCI System Management
    (PCI) 5 Studio PCTV (Audio)
    (ISA) 6 Standard floppy disk controller
    (ISA) 8 System CMOS/real time clock
    (ISA) 9 Microsoft ACPI-Compliant System
    (ISA) 13 Numeric data processor
    (ISA) 14 Primary IDE Channel
    (ISA) 15 Secondary IDE Channel
    (PCI) 16 Creative SB Audigy
    (PCI) 16 Studio PCTV
    (PCI) 17 OHCI Compliant IEEE 1394 Host Controller
    (PCI) 17 Realtek RTL8139/810x Family Fast Ethernet NIC
    (PCI) 19 NVIDIA GeForce4 Ti 4200 with AGP8X
    (PCI) 20 Standard OpenHCD USB Host Controller
    (PCI) 21 Standard Enhanced PCI to USB Host Controller
    (PCI) 22 Standard OpenHCD USB Host Controller

    Disable Spread Spectrum for both the CPU and AGP, Disable any BIOS caching and shadowing
    What unified driver package did you install? I recommend using the 2.03's
    Please create a signature in your profile like mine.
    I don't think this is directly related to your video card.
    If no help here:
    Post this question in the nForce forum too and tell them I told you to.
    The reason is someone may have had this problem from that forum but deos not visit this one. I also suggest you post this question over at http://www.nforcershq.com/forum/ to see if they have experienced it.
    I know I have experienced this problem but for the life of me I cannot remember what it was that fixed it.
    Your sound and TV card are sharing IRQ's, you really should try to swap PCI slots so the Audigy is on it's own and the same goes with the TV card. I know slot 3 is a good spot for the TV card, you may have to swap till you get the best IRQ allocation.
    Post about the SOD not the VGA in the nForce forum

  • [Solved] HP Omen 15 - Slow SSD after IRQ 16 error

    [EDIT]
    Sorry for wasting everyone's time. It turned out that I had only tried installing nvidia/bumblebee without the nomodeset option..and apparently that didn't work properly for some reason.
    So if anyone else runs into this problem here's the solution:
    1) Boot your installation media with the 'nomodeset' kernel option (this is especially important for live images (fedora,ubuntu,...) which are completely unusable otherwise
    2) With nomodeset still enabled, install the nvidia driver, bumblebee and bbswitch
    4) Enable bumblebeed.service
    3) remove the nomodeset option
    Also I updated the microcode on the CPU, but as far as I could tell that didn't affect anything.
    [/EDIT]
    Hi everyone,
    I bought a new HP Omen 15 laptop. In Windows everything runs fine, but on Linux I get an IRQ 16 error after which SSD reads become so painfully slow that the system becomes mostly unusable. This issue has been posted by someone on the Ubuntu forums, but nobody had a solution there.
    Hopefully one of you will be able to help me, because right now I'm stuck on Windows for doing my work...and I get absolutely no joy out of that
    Hardware:
    i7-4710HQ
    Nvidia GeForce GTX 860 and Intel® HD Graphics 4600
    512GB Samsung XP941 SSD (M.2)
    Currently the system dual-boots with Windows 8.1, secure boot disabled, using gummiboot on the windows UEFI partition.
    The actual error that (I think) leads to the performance hit is
    [ 13.608625] 0000000000000000 96859b6ad089d33d ffff88045f243e28 ffffffff8154fb74
    [ 13.608632] 0000000000000000 ffff880083514e00 ffff88045f243e58 ffffffff810cd406
    [ 13.608637] 000000013ffeb056 ffff880083514e00 0000000000000000 0000000000000010
    [ 13.608643] Call Trace:
    [ 13.608646] <IRQ> [<ffffffff8154fb74>] dump_stack+0x4e/0x71
    [ 13.608665] [<ffffffff810cd406>] __report_bad_irq+0x36/0xd0
    [ 13.608671] [<ffffffff810cd7b7>] note_interrupt+0x257/0x2a0
    [ 13.608677] [<ffffffff810cacee>] handle_irq_event_percpu+0xae/0x1f0
    [ 13.608682] [<ffffffff810cae71>] handle_irq_event+0x41/0x70
    [ 13.608689] [<ffffffff810cdd47>] handle_fasteoi_irq+0x87/0x140
    [ 13.608698] [<ffffffff81017362>] handle_irq+0x22/0x40
    [ 13.608704] [<ffffffff815581b1>] do_IRQ+0x51/0xf0
    [ 13.608711] [<ffffffff815561ad>] common_interrupt+0x6d/0x6d
    [ 13.608714] <EOI> [<ffffffff81403aa5>] ? cpuidle_enter_state+0x65/0x1a0
    [ 13.608730] [<ffffffff81403a91>] ? cpuidle_enter_state+0x51/0x1a0
    [ 13.608737] [<ffffffff81403cc7>] cpuidle_enter+0x17/0x20
    [ 13.608745] [<ffffffff810b3539>] cpu_startup_entry+0x3d9/0x460
    [ 13.608752] [<ffffffff8104a994>] start_secondary+0x1b4/0x1f0
    [ 13.608756] handlers:
    [ 13.608809] [<ffffffffa0128410>] ahci_single_irq_intr [libahci]
    [ 13.608873] Disabling IRQ #16
    What's interesting is, that this problem does not occur if I set the 'nomodeset' kernel option. So probably it's somehow related to graphics. The performance drop is quite visible:
    With nomodeset:
    hdparm -Tt --verbose /dev/sda
    /dev/sda:
    Timing cached reads: 21006 MB in 2.00 seconds = 10513.48 MB/sec
    Timing buffered disk reads: 2378 MB in 3.00 seconds = 792.36 MB/sec
    ...and without:
    hdparm -Tt --verbose /dev/sda
    /dev/sda:
    Timing cached reads: 12274 MB in 2.00 seconds = 6140.85 MB/sec
    Timing buffered disk reads: 8 MB in 3.20 seconds = 2.50 MB/sec
    So just about 0.3% of the original speed.
    The above information are form a fresh install without any additional packages installed. Installing nvidia/intel/bumblebee did not help either, so I've left it in the fresh state to be debuggable.
    Here are various outputs from some commands that might be useful to determine the error source, let me know if you need anything else!
    hdparm /dev/sda
    /dev/sda:
    multcount = 0 (off)
    IO_support = 1 (32-bit)
    readonly = 0 (off)
    readahead = 256 (on)
    geometry = 62260/255/63, sectors = 1000215216, start = 0
    lspci
    00:00.0 Host bridge: Intel Corporation Xeon E3-1200 v3/4th Gen Core Processor DRAM Controller (rev 06)
    00:01.0 PCI bridge: Intel Corporation Xeon E3-1200 v3/4th Gen Core Processor PCI Express x16 Controller (rev 06)
    00:02.0 VGA compatible controller: Intel Corporation 4th Gen Core Processor Integrated Graphics Controller (rev 06)
    00:03.0 Audio device: Intel Corporation Xeon E3-1200 v3/4th Gen Core Processor HD Audio Controller (rev 06)
    00:14.0 USB controller: Intel Corporation 8 Series/C220 Series Chipset Family USB xHCI (rev 05)
    00:16.0 Communication controller: Intel Corporation 8 Series/C220 Series Chipset Family MEI Controller #1 (rev 04)
    00:1b.0 Audio device: Intel Corporation 8 Series/C220 Series Chipset High Definition Audio Controller (rev 05)
    00:1c.0 PCI bridge: Intel Corporation 8 Series/C220 Series Chipset Family PCI Express Root Port #1 (rev d5)
    00:1c.4 PCI bridge: Intel Corporation 8 Series/C220 Series Chipset Family PCI Express Root Port #5 (rev d5)
    00:1c.5 PCI bridge: Intel Corporation 8 Series/C220 Series Chipset Family PCI Express Root Port #6 (rev d5)
    00:1f.0 ISA bridge: Intel Corporation HM87 Express LPC Controller (rev 05)
    00:1f.2 SATA controller: Intel Corporation 8 Series/C220 Series Chipset Family 6-port SATA Controller 1 [AHCI mode] (rev 05)
    00:1f.3 SMBus: Intel Corporation 8 Series/C220 Series Chipset Family SMBus Controller (rev 05)
    01:00.0 3D controller: NVIDIA Corporation GM107M [GeForce GTX 860M] (rev a2)
    07:00.0 SATA controller: Samsung Electronics Co Ltd XP941 PCIe SSD (rev 01)
    08:00.0 Unassigned class [ff00]: Realtek Semiconductor Co., Ltd. RTS5227 PCI Express Card Reader (rev 01)
    09:00.0 Network controller: Intel Corporation Wireless 7260 (rev c3)
    cat /proc/interrupts
    CPU0 CPU1 CPU2 CPU3 CPU4 CPU5 CPU6 CPU7
    0: 24 0 0 0 0 0 0 0 IR-IO-APIC-edge timer
    1: 901 2 2 1 3 1 1 0 IR-IO-APIC-edge i8042
    8: 1 0 0 0 0 0 0 0 IR-IO-APIC-edge rtc0
    9: 199 49 37 75 13 25 6 18 IR-IO-APIC-fasteoi acpi
    12: 4419 17 5 8 2 6 7 7 IR-IO-APIC-edge i8042
    16: 3146 195401 312 395 353 184 102 108 IR-IO-APIC 16-fasteoi 0000:07:00.0
    24: 0 0 0 0 0 0 0 0 DMAR_MSI-edge dmar0
    25: 0 0 0 0 0 0 0 0 DMAR_MSI-edge dmar1
    26: 0 0 0 0 0 0 0 0 IR-PCI-MSI-edge PCIe PME
    27: 0 0 0 0 0 0 0 0 IR-PCI-MSI-edge PCIe PME
    28: 0 0 0 0 0 0 0 0 IR-PCI-MSI-edge PCIe PME
    29: 0 0 0 0 0 0 0 0 IR-PCI-MSI-edge PCIe PME
    30: 6 1 2 9 1 0 1 2 IR-PCI-MSI-edge rtsx_pci
    31: 574 190 28 34 154 29 11 7 IR-PCI-MSI-edge xhci_hcd
    32: 0 0 0 0 0 0 0 0 IR-PCI-MSI-edge 0000:00:1f.2
    33: 1 0 0 0 0 0 3 7 IR-PCI-MSI-edge mei_me
    34: 5 138 79 0 5 76 10 0 IR-PCI-MSI-edge snd_hda_intel
    35: 169 0 1 0 1 0 0 0 IR-PCI-MSI-edge i915
    36: 17 3 2 7 6 14 2 11 IR-PCI-MSI-edge iwlwifi
    37: 1 26 0 0 32 0 0 0 IR-PCI-MSI-edge snd_hda_intel
    NMI: 0 0 0 0 0 0 0 0 Non-maskable interrupts
    LOC: 958 2678 1069 355 1505 562 682 321 Local timer interrupts
    SPU: 0 0 0 0 0 0 0 0 Spurious interrupts
    PMI: 0 0 0 0 0 0 0 0 Performance monitoring interrupts
    IWI: 1 1 0 1 0 0 0 0 IRQ work interrupts
    RTR: 0 0 0 0 0 0 0 0 APIC ICR read retries
    RES: 204 193 207 200 136 177 195 285 Rescheduling interrupts
    CAL: 898 819 847 830 822 853 843 869 Function call interrupts
    TLB: 10 6 8 3 4 7 3 5 TLB shootdowns
    TRM: 0 0 0 0 0 0 0 0 Thermal event interrupts
    THR: 0 0 0 0 0 0 0 0 Threshold APIC interrupts
    MCE: 0 0 0 0 0 0 0 0 Machine check exceptions
    MCP: 2 2 2 2 2 2 2 2 Machine check polls
    HYP: 0 0 0 0 0 0 0 0 Hypervisor callback interrupts
    ERR: 0
    MIS: 0
    dmesg
    [ 0.000000] Initializing cgroup subsys cpuset
    [ 0.000000] Initializing cgroup subsys cpu
    [ 0.000000] Initializing cgroup subsys cpuacct
    [ 0.000000] Linux version 3.18.6-1-ARCH (builduser@tobias) (gcc version 4.9.2 20141224 (prerelease) (GCC) ) #1 SMP PREEMPT Sat Feb 7 08:44:05 CET 2015
    [ 0.000000] Command line: initrd=\initramfs-linux.img root=/dev/mapper/VolGroup00-lv_root rw
    [ 0.000000] e820: BIOS-provided physical RAM map:
    [ 0.000000] BIOS-e820: [mem 0x0000000000000000-0x000000000006efff] usable
    [ 0.000000] BIOS-e820: [mem 0x000000000006f000-0x000000000006ffff] reserved
    [ 0.000000] BIOS-e820: [mem 0x0000000000070000-0x0000000000087fff] usable
    [ 0.000000] BIOS-e820: [mem 0x0000000000088000-0x00000000000bffff] reserved
    [ 0.000000] BIOS-e820: [mem 0x0000000000100000-0x000000009c07efff] usable
    [ 0.000000] BIOS-e820: [mem 0x000000009c07f000-0x000000009ce7efff] reserved
    [ 0.000000] BIOS-e820: [mem 0x000000009ce7f000-0x000000009cf7efff] ACPI NVS
    [ 0.000000] BIOS-e820: [mem 0x000000009cf7f000-0x000000009cffefff] ACPI data
    [ 0.000000] BIOS-e820: [mem 0x000000009cfff000-0x000000009cffffff] usable
    [ 0.000000] BIOS-e820: [mem 0x000000009d000000-0x000000009f9fffff] reserved
    [ 0.000000] BIOS-e820: [mem 0x00000000e0000000-0x00000000efffffff] reserved
    [ 0.000000] BIOS-e820: [mem 0x00000000feb00000-0x00000000feb0ffff] reserved
    [ 0.000000] BIOS-e820: [mem 0x00000000fec00000-0x00000000fec00fff] reserved
    [ 0.000000] BIOS-e820: [mem 0x00000000fed00000-0x00000000fee00fff] reserved
    [ 0.000000] BIOS-e820: [mem 0x00000000ffb00000-0x00000000ffffffff] reserved
    [ 0.000000] BIOS-e820: [mem 0x0000000100000000-0x000000045f5fffff] usable
    [ 0.000000] NX (Execute Disable) protection: active
    [ 0.000000] e820: update [mem 0x78e8e018-0x78ea7657] usable ==> usable
    [ 0.000000] e820: update [mem 0x78e7d018-0x78e8d057] usable ==> usable
    [ 0.000000] extended physical RAM map:
    [ 0.000000] reserve setup_data: [mem 0x0000000000000000-0x000000000006efff] usable
    [ 0.000000] reserve setup_data: [mem 0x000000000006f000-0x000000000006ffff] reserved
    [ 0.000000] reserve setup_data: [mem 0x0000000000070000-0x0000000000087fff] usable
    [ 0.000000] reserve setup_data: [mem 0x0000000000088000-0x00000000000bffff] reserved
    [ 0.000000] reserve setup_data: [mem 0x0000000000100000-0x0000000078e7d017] usable
    [ 0.000000] reserve setup_data: [mem 0x0000000078e7d018-0x0000000078e8d057] usable
    [ 0.000000] reserve setup_data: [mem 0x0000000078e8d058-0x0000000078e8e017] usable
    [ 0.000000] reserve setup_data: [mem 0x0000000078e8e018-0x0000000078ea7657] usable
    [ 0.000000] reserve setup_data: [mem 0x0000000078ea7658-0x000000009c07efff] usable
    [ 0.000000] reserve setup_data: [mem 0x000000009c07f000-0x000000009ce7efff] reserved
    [ 0.000000] reserve setup_data: [mem 0x000000009ce7f000-0x000000009cf7efff] ACPI NVS
    [ 0.000000] reserve setup_data: [mem 0x000000009cf7f000-0x000000009cffefff] ACPI data
    [ 0.000000] reserve setup_data: [mem 0x000000009cfff000-0x000000009cffffff] usable
    [ 0.000000] reserve setup_data: [mem 0x000000009d000000-0x000000009f9fffff] reserved
    [ 0.000000] reserve setup_data: [mem 0x00000000e0000000-0x00000000efffffff] reserved
    [ 0.000000] reserve setup_data: [mem 0x00000000feb00000-0x00000000feb0ffff] reserved
    [ 0.000000] reserve setup_data: [mem 0x00000000fec00000-0x00000000fec00fff] reserved
    [ 0.000000] reserve setup_data: [mem 0x00000000fed00000-0x00000000fee00fff] reserved
    [ 0.000000] reserve setup_data: [mem 0x00000000ffb00000-0x00000000ffffffff] reserved
    [ 0.000000] reserve setup_data: [mem 0x0000000100000000-0x000000045f5fffff] usable
    [ 0.000000] efi: EFI v2.31 by INSYDE Corp.
    [ 0.000000] efi: ACPI=0x9cffe000 ACPI 2.0=0x9cffe014 SMBIOS=0x9ce7df18
    [ 0.000000] efi: mem00: [Boot Code | | | | | |WB|WT|WC|UC] range=[0x0000000000000000-0x0000000000001000) (0MB)
    [ 0.000000] efi: mem01: [Loader Data | | | | | |WB|WT|WC|UC] range=[0x0000000000001000-0x0000000000007000) (0MB)
    [ 0.000000] efi: mem02: [Conventional Memory| | | | | |WB|WT|WC|UC] range=[0x0000000000007000-0x000000000006f000) (0MB)
    [ 0.000000] efi: mem03: [Reserved | | | | | |WB|WT|WC|UC] range=[0x000000000006f000-0x0000000000070000) (0MB)
    [ 0.000000] efi: mem04: [Conventional Memory| | | | | |WB|WT|WC|UC] range=[0x0000000000070000-0x0000000000088000) (0MB)
    [ 0.000000] efi: mem05: [Runtime Data |RUN| | | | |WB|WT|WC|UC] range=[0x0000000000088000-0x000000000009f000) (0MB)
    [ 0.000000] efi: mem06: [Reserved | | | | | |WB|WT|WC|UC] range=[0x000000000009f000-0x00000000000a0000) (0MB)
    [ 0.000000] efi: mem07: [Conventional Memory| | | | | |WB|WT|WC|UC] range=[0x0000000000100000-0x0000000001000000) (15MB)
    [ 0.000000] efi: mem08: [Loader Data | | | | | |WB|WT|WC|UC] range=[0x0000000001000000-0x0000000001e3b000) (14MB)
    [ 0.000000] efi: mem09: [Conventional Memory| | | | | |WB|WT|WC|UC] range=[0x0000000001e3b000-0x0000000078680000) (1896MB)
    [ 0.000000] efi: mem10: [Boot Data | | | | | |WB|WT|WC|UC] range=[0x0000000078680000-0x00000000786a0000) (0MB)
    [ 0.000000] efi: mem11: [Conventional Memory| | | | | |WB|WT|WC|UC] range=[0x00000000786a0000-0x0000000078e7d000) (7MB)
    [ 0.000000] efi: mem12: [Loader Data | | | | | |WB|WT|WC|UC] range=[0x0000000078e7d000-0x0000000078ea8000) (0MB)
    [ 0.000000] efi: mem13: [Loader Code | | | | | |WB|WT|WC|UC] range=[0x0000000078ea8000-0x000000007ace3000) (30MB)
    [ 0.000000] efi: mem14: [Boot Data | | | | | |WB|WT|WC|UC] range=[0x000000007ace3000-0x000000007b670000) (9MB)
    [ 0.000000] efi: mem15: [Conventional Memory| | | | | |WB|WT|WC|UC] range=[0x000000007b670000-0x000000007b67a000) (0MB)
    [ 0.000000] efi: mem16: [Loader Data | | | | | |WB|WT|WC|UC] range=[0x000000007b67a000-0x000000007b67f000) (0MB)
    [ 0.000000] efi: mem17: [Conventional Memory| | | | | |WB|WT|WC|UC] range=[0x000000007b67f000-0x000000007b865000) (1MB)
    [ 0.000000] efi: mem18: [Loader Code | | | | | |WB|WT|WC|UC] range=[0x000000007b865000-0x000000007b87f000) (0MB)
    [ 0.000000] efi: mem19: [Conventional Memory| | | | | |WB|WT|WC|UC] range=[0x000000007b87f000-0x000000007f7d2000) (63MB)
    [ 0.000000] efi: mem20: [Loader Data | | | | | |WB|WT|WC|UC] range=[0x000000007f7d2000-0x000000008001a000) (8MB)
    [ 0.000000] efi: mem21: [Boot Data | | | | | |WB|WT|WC|UC] range=[0x000000008001a000-0x0000000081106000) (16MB)
    [ 0.000000] efi: mem22: [Conventional Memory| | | | | |WB|WT|WC|UC] range=[0x0000000081106000-0x00000000815f5000) (4MB)
    [ 0.000000] efi: mem23: [Boot Data | | | | | |WB|WT|WC|UC] range=[0x00000000815f5000-0x000000008161b000) (0MB)
    [ 0.000000] efi: mem24: [Conventional Memory| | | | | |WB|WT|WC|UC] range=[0x000000008161b000-0x0000000081659000) (0MB)
    [ 0.000000] efi: mem25: [Boot Data | | | | | |WB|WT|WC|UC] range=[0x0000000081659000-0x00000000819e1000) (3MB)
    [ 0.000000] efi: mem26: [Conventional Memory| | | | | |WB|WT|WC|UC] range=[0x00000000819e1000-0x00000000819e2000) (0MB)
    [ 0.000000] efi: mem27: [Boot Data | | | | | |WB|WT|WC|UC] range=[0x00000000819e2000-0x00000000819fe000) (0MB)
    [ 0.000000] efi: mem28: [Conventional Memory| | | | | |WB|WT|WC|UC] range=[0x00000000819fe000-0x0000000081a04000) (0MB)
    [ 0.000000] efi: mem29: [Boot Data | | | | | |WB|WT|WC|UC] range=[0x0000000081a04000-0x0000000081a0c000) (0MB)
    [ 0.000000] efi: mem30: [Conventional Memory| | | | | |WB|WT|WC|UC] range=[0x0000000081a0c000-0x0000000081a0d000) (0MB)
    [ 0.000000] efi: mem31: [Boot Data | | | | | |WB|WT|WC|UC] range=[0x0000000081a0d000-0x0000000081a38000) (0MB)
    [ 0.000000] efi: mem32: [Conventional Memory| | | | | |WB|WT|WC|UC] range=[0x0000000081a38000-0x0000000081a3a000) (0MB)
    [ 0.000000] efi: mem33: [Boot Data | | | | | |WB|WT|WC|UC] range=[0x0000000081a3a000-0x0000000081b48000) (1MB)
    [ 0.000000] efi: mem34: [Conventional Memory| | | | | |WB|WT|WC|UC] range=[0x0000000081b48000-0x0000000081b49000) (0MB)
    [ 0.000000] efi: mem35: [Boot Data | | | | | |WB|WT|WC|UC] range=[0x0000000081b49000-0x0000000081bcc000) (0MB)
    [ 0.000000] efi: mem36: [Conventional Memory| | | | | |WB|WT|WC|UC] range=[0x0000000081bcc000-0x0000000081bd4000) (0MB)
    [ 0.000000] efi: mem37: [Boot Data | | | | | |WB|WT|WC|UC] range=[0x0000000081bd4000-0x0000000081bd5000) (0MB)
    [ 0.000000] efi: mem38: [Conventional Memory| | | | | |WB|WT|WC|UC] range=[0x0000000081bd5000-0x0000000081bd7000) (0MB)
    [ 0.000000] efi: mem39: [Boot Data | | | | | |WB|WT|WC|UC] range=[0x0000000081bd7000-0x0000000081bd8000) (0MB)
    [ 0.000000] efi: mem40: [Conventional Memory| | | | | |WB|WT|WC|UC] range=[0x0000000081bd8000-0x0000000081bd9000) (0MB)
    [ 0.000000] efi: mem41: [Boot Data | | | | | |WB|WT|WC|UC] range=[0x0000000081bd9000-0x0000000081c1b000) (0MB)
    [ 0.000000] efi: mem42: [Conventional Memory| | | | | |WB|WT|WC|UC] range=[0x0000000081c1b000-0x0000000081c1c000) (0MB)
    [ 0.000000] efi: mem43: [Boot Data | | | | | |WB|WT|WC|UC] range=[0x0000000081c1c000-0x0000000081c20000) (0MB)
    [ 0.000000] efi: mem44: [Conventional Memory| | | | | |WB|WT|WC|UC] range=[0x0000000081c20000-0x0000000081c22000) (0MB)
    [ 0.000000] efi: mem45: [Boot Data | | | | | |WB|WT|WC|UC] range=[0x0000000081c22000-0x0000000081c2d000) (0MB)
    [ 0.000000] efi: mem46: [Conventional Memory| | | | | |WB|WT|WC|UC] range=[0x0000000081c2d000-0x0000000081c30000) (0MB)
    [ 0.000000] efi: mem47: [Boot Data | | | | | |WB|WT|WC|UC] range=[0x0000000081c30000-0x0000000081c52000) (0MB)
    [ 0.000000] efi: mem48: [Conventional Memory| | | | | |WB|WT|WC|UC] range=[0x0000000081c52000-0x0000000081c53000) (0MB)
    [ 0.000000] efi: mem49: [Boot Data | | | | | |WB|WT|WC|UC] range=[0x0000000081c53000-0x0000000081c76000) (0MB)
    [ 0.000000] efi: mem50: [Conventional Memory| | | | | |WB|WT|WC|UC] range=[0x0000000081c76000-0x0000000081c77000) (0MB)
    [ 0.000000] efi: mem51: [Boot Data | | | | | |WB|WT|WC|UC] range=[0x0000000081c77000-0x0000000081c78000) (0MB)
    [ 0.000000] efi: mem52: [Conventional Memory| | | | | |WB|WT|WC|UC] range=[0x0000000081c78000-0x0000000081c7a000) (0MB)
    [ 0.000000] efi: mem53: [Boot Data | | | | | |WB|WT|WC|UC] range=[0x0000000081c7a000-0x000000008387f000) (28MB)
    [ 0.000000] efi: mem54: [Conventional Memory| | | | | |WB|WT|WC|UC] range=[0x000000008387f000-0x000000009bc0e000) (387MB)
    [ 0.000000] efi: mem55: [Boot Code | | | | | |WB|WT|WC|UC] range=[0x000000009bc0e000-0x000000009c07f000) (4MB)
    [ 0.000000] efi: mem56: [Runtime Code |RUN| | | | |WB|WT|WC|UC] range=[0x000000009c07f000-0x000000009c47f000) (4MB)
    [ 0.000000] efi: mem57: [Runtime Data |RUN| | | | |WB|WT|WC|UC] range=[0x000000009c47f000-0x000000009c67f000) (2MB)
    [ 0.000000] efi: mem58: [Reserved | | | | | |WB|WT|WC|UC] range=[0x000000009c67f000-0x000000009ce7f000) (8MB)
    [ 0.000000] efi: mem59: [ACPI Memory NVS | | | | | |WB|WT|WC|UC] range=[0x000000009ce7f000-0x000000009cf7f000) (1MB)
    [ 0.000000] efi: mem60: [ACPI Reclaim Memory| | | | | |WB|WT|WC|UC] range=[0x000000009cf7f000-0x000000009cfff000) (0MB)
    [ 0.000000] efi: mem61: [Boot Data | | | | | |WB|WT|WC|UC] range=[0x000000009cfff000-0x000000009d000000) (0MB)
    [ 0.000000] efi: mem62: [Conventional Memory| | | | | |WB|WT|WC|UC] range=[0x0000000100000000-0x000000045f600000) (13814MB)
    [ 0.000000] efi: mem63: [Reserved | | | | | | | | | ] range=[0x00000000000a0000-0x00000000000c0000) (0MB)
    [ 0.000000] efi: mem64: [Reserved | | | | | | | | | ] range=[0x000000009d000000-0x000000009fa00000) (42MB)
    [ 0.000000] efi: mem65: [Memory Mapped I/O |RUN| | | | | | | |UC] range=[0x00000000e0000000-0x00000000f0000000) (256MB)
    [ 0.000000] efi: mem66: [Memory Mapped I/O |RUN| | | | | | | |UC] range=[0x00000000feb00000-0x00000000feb10000) (0MB)
    [ 0.000000] efi: mem67: [Memory Mapped I/O |RUN| | | | | | | |UC] range=[0x00000000fec00000-0x00000000fec01000) (0MB)
    [ 0.000000] efi: mem68: [Memory Mapped I/O |RUN| | | | | | | |UC] range=[0x00000000fed00000-0x00000000fed1c000) (0MB)
    [ 0.000000] efi: mem69: [Memory Mapped I/O |RUN| | | | | | | | ] range=[0x00000000fed1c000-0x00000000fed20000) (0MB)
    [ 0.000000] efi: mem70: [Memory Mapped I/O |RUN| | | | | | | |UC] range=[0x00000000fed20000-0x00000000fee01000) (0MB)
    [ 0.000000] efi: mem71: [Memory Mapped I/O |RUN| | | | | | | |UC] range=[0x00000000ffb00000-0x0000000100000000) (5MB)
    [ 0.000000] SMBIOS 2.8 present.
    [ 0.000000] DMI: Hewlett-Packard HP OMEN Notebook PC 15/2332, BIOS F.09 12/27/2014
    [ 0.000000] e820: update [mem 0x00000000-0x00000fff] usable ==> reserved
    [ 0.000000] e820: remove [mem 0x000a0000-0x000fffff] usable
    [ 0.000000] AGP: No AGP bridge found
    [ 0.000000] e820: last_pfn = 0x45f600 max_arch_pfn = 0x400000000
    [ 0.000000] MTRR default type: uncachable
    [ 0.000000] MTRR fixed ranges enabled:
    [ 0.000000] 00000-9FFFF write-back
    [ 0.000000] A0000-BFFFF uncachable
    [ 0.000000] C0000-E7FFF write-protect
    [ 0.000000] E8000-EFFFF write-combining
    [ 0.000000] F0000-FFFFF write-protect
    [ 0.000000] MTRR variable ranges enabled:
    [ 0.000000] 0 base 0000000000 mask 7800000000 write-back
    [ 0.000000] 1 base 009D000000 mask 7FFF000000 uncachable
    [ 0.000000] 2 base 009E000000 mask 7FFE000000 uncachable
    [ 0.000000] 3 base 00A0000000 mask 7FE0000000 uncachable
    [ 0.000000] 4 base 00C0000000 mask 7FC0000000 uncachable
    [ 0.000000] 5 disabled
    [ 0.000000] 6 disabled
    [ 0.000000] 7 disabled
    [ 0.000000] 8 disabled
    [ 0.000000] 9 disabled
    [ 0.000000] x86 PAT enabled: cpu 0, old 0x7040600070406, new 0x7010600070106
    [ 0.000000] e820: update [mem 0x9d000000-0xffffffff] usable ==> reserved
    [ 0.000000] e820: last_pfn = 0x9d000 max_arch_pfn = 0x400000000
    [ 0.000000] Scanning 1 areas for low memory corruption
    [ 0.000000] Base memory trampoline at [ffff880000082000] 82000 size 24576
    [ 0.000000] Using GB pages for direct mapping
    [ 0.000000] init_memory_mapping: [mem 0x00000000-0x000fffff]
    [ 0.000000] [mem 0x00000000-0x000fffff] page 4k
    [ 0.000000] BRK [0x01b36000, 0x01b36fff] PGTABLE
    [ 0.000000] BRK [0x01b37000, 0x01b37fff] PGTABLE
    [ 0.000000] BRK [0x01b38000, 0x01b38fff] PGTABLE
    [ 0.000000] init_memory_mapping: [mem 0x45f400000-0x45f5fffff]
    [ 0.000000] [mem 0x45f400000-0x45f5fffff] page 2M
    [ 0.000000] BRK [0x01b39000, 0x01b39fff] PGTABLE
    [ 0.000000] init_memory_mapping: [mem 0x45c000000-0x45f3fffff]
    [ 0.000000] [mem 0x45c000000-0x45f3fffff] page 2M
    [ 0.000000] init_memory_mapping: [mem 0x400000000-0x45bffffff]
    [ 0.000000] [mem 0x400000000-0x43fffffff] page 1G
    [ 0.000000] [mem 0x440000000-0x45bffffff] page 2M
    [ 0.000000] init_memory_mapping: [mem 0x00100000-0x9c07efff]
    [ 0.000000] [mem 0x00100000-0x001fffff] page 4k
    [ 0.000000] [mem 0x00200000-0x3fffffff] page 2M
    [ 0.000000] [mem 0x40000000-0x7fffffff] page 1G
    [ 0.000000] [mem 0x80000000-0x9bffffff] page 2M
    [ 0.000000] [mem 0x9c000000-0x9c07efff] page 4k
    [ 0.000000] init_memory_mapping: [mem 0x9cfff000-0x9cffffff]
    [ 0.000000] [mem 0x9cfff000-0x9cffffff] page 4k
    [ 0.000000] BRK [0x01b3a000, 0x01b3afff] PGTABLE
    [ 0.000000] init_memory_mapping: [mem 0x100000000-0x3ffffffff]
    [ 0.000000] [mem 0x100000000-0x3ffffffff] page 1G
    [ 0.000000] RAMDISK: [mem 0x7f7d2000-0x80019fff]
    [ 0.000000] ACPI: Early table checksum verification disabled
    [ 0.000000] ACPI: RSDP 0x000000009CFFE014 000024 (v02 HPQOEM)
    [ 0.000000] ACPI: XSDT 0x000000009CFFE210 0000F4 (v01 HPQOEM SLIC-MPC 00000001 HP 01000013)
    [ 0.000000] ACPI: FACP 0x000000009CFF7000 00010C (v05 HPQOEM SLIC-MPC 00000001 HP 00040000)
    [ 0.000000] ACPI: DSDT 0x000000009CFDB000 018700 (v02 HPQOEM SLIC-MPC 00000000 ACPI 00040000)
    [ 0.000000] ACPI: FACS 0x000000009CF67000 000040
    [ 0.000000] ACPI: TCPA 0x000000009CFFD000 000032 (v02 HPQOEM INSYDE 00000000 HP 00040000)
    [ 0.000000] ACPI: UEFI 0x000000009CFFC000 000236 (v01 HPQOEM INSYDE 00000001 HP 00040000)
    [ 0.000000] ACPI: FPDT 0x000000009CFFA000 000044 (v01 HPQOEM SLIC-MPC 00000001 HP 00040000)
    [ 0.000000] ACPI: MSDM 0x000000009CFF9000 000055 (v03 HPQOEM SLIC-MPC 00000001 HP 00040000)
    [ 0.000000] ACPI: ASF! 0x000000009CFF8000 0000A5 (v32 HPQOEM INSYDE 00000001 HP 00040000)
    [ 0.000000] ACPI: HPET 0x000000009CFF6000 000038 (v01 HPQOEM INSYDE 00000001 HP 00040000)
    [ 0.000000] ACPI: APIC 0x000000009CFF5000 00008C (v03 HPQOEM SLIC-MPC 00000001 HP 00040000)
    [ 0.000000] ACPI: MCFG 0x000000009CFF4000 00003C (v01 HPQOEM INSYDE 00000001 HP 00040000)
    [ 0.000000] ACPI: WDAT 0x000000009CFDA000 000224 (v01 HPQOEM INSYDE 00000001 HP 00040000)
    [ 0.000000] ACPI: SSDT 0x000000009CFD9000 0007F6 (v01 HPQOEM INSYDE 00001000 ACPI 00040000)
    [ 0.000000] ACPI: BOOT 0x000000009CFD7000 000028 (v01 HPQOEM INSYDE 00000001 HP 00040000)
    [ 0.000000] ACPI: LPIT 0x000000009CFD6000 000094 (v01 HPQOEM INSYDE 00000000 HP 00040000)
    [ 0.000000] ACPI: SSDT 0x000000009CFD5000 0003E1 (v01 HPQOEM INSYDE 00001000 ACPI 00040000)
    [ 0.000000] ACPI: ASPT 0x000000009CFD4000 000034 (v07 HPQOEM INSYDE 00000001 HP 00040000)
    [ 0.000000] ACPI: DBGP 0x000000009CFD3000 000034 (v01 HPQOEM SLIC-MPC 00000001 HP 00040000)
    [ 0.000000] ACPI: SSDT 0x000000009CFCB000 000539 (v01 HPQOEM INSYDE 00003000 ACPI 00040000)
    [ 0.000000] ACPI: SSDT 0x000000009CFCA000 000AD8 (v01 HPQOEM INSYDE 00003000 ACPI 00040000)
    [ 0.000000] ACPI: SSDT 0x000000009CFC6000 003361 (v01 HPQOEM INSYDE 00003000 ACPI 00040000)
    [ 0.000000] ACPI: SSDT 0x000000009CFBE000 003FC4 (v01 HPQOEM INSYDE 00001000 ACPI 00040000)
    [ 0.000000] ACPI: SSDT 0x000000009CFC5000 00040A (v01 HPQOEM INSYDE 00001000 ACPI 00040000)
    [ 0.000000] ACPI: WDTT 0x000000009CFC4000 000224 (v02 HPQOEM INSYDE 00000001 HP 00040000)
    [ 0.000000] ACPI: SSDT 0x000000009CFC3000 00006B (v01 HPQOEM INSYDE 00001000 ACPI 00040000)
    [ 0.000000] ACPI: BGRT 0x000000009CFC2000 000038 (v01 HPQOEM INSYDE 00000001 HP 00040000)
    [ 0.000000] ACPI: TPM2 0x000000009CFBD000 000044 (v03 HPQOEM INSYDE 00000001 HP 00040000)
    [ 0.000000] ACPI: DMAR 0x000000009CFBC000 0000A8 (v01 HPQOEM INSYDE 00000001 HP 00040000)
    [ 0.000000] ACPI: Local APIC address 0xfee00000
    [ 0.000000] No NUMA configuration found
    [ 0.000000] Faking a node at [mem 0x0000000000000000-0x000000045f5fffff]
    [ 0.000000] NODE_DATA(0) allocated [mem 0x45f5fa000-0x45f5fdfff]
    [ 0.000000] [ffffea0000000000-ffffea00117fffff] PMD -> [ffff88044ec00000-ffff88045ebfffff] on node 0
    [ 0.000000] Zone ranges:
    [ 0.000000] DMA [mem 0x00001000-0x00ffffff]
    [ 0.000000] DMA32 [mem 0x01000000-0xffffffff]
    [ 0.000000] Normal [mem 0x100000000-0x45f5fffff]
    [ 0.000000] Movable zone start for each node
    [ 0.000000] Early memory node ranges
    [ 0.000000] node 0: [mem 0x00001000-0x0006efff]
    [ 0.000000] node 0: [mem 0x00070000-0x00087fff]
    [ 0.000000] node 0: [mem 0x00100000-0x9c07efff]
    [ 0.000000] node 0: [mem 0x9cfff000-0x9cffffff]
    [ 0.000000] node 0: [mem 0x100000000-0x45f5fffff]
    [ 0.000000] Initmem setup node 0 [mem 0x00001000-0x45f5fffff]
    [ 0.000000] On node 0 totalpages: 4175366
    [ 0.000000] DMA zone: 64 pages used for memmap
    [ 0.000000] DMA zone: 21 pages reserved
    [ 0.000000] DMA zone: 3974 pages, LIFO batch:0
    [ 0.000000] DMA32 zone: 9922 pages used for memmap
    [ 0.000000] DMA32 zone: 635008 pages, LIFO batch:31
    [ 0.000000] Normal zone: 55256 pages used for memmap
    [ 0.000000] Normal zone: 3536384 pages, LIFO batch:31
    [ 0.000000] Reserving Intel graphics stolen memory at 0x9da00000-0x9f9fffff
    [ 0.000000] ACPI: PM-Timer IO Port: 0x1808
    [ 0.000000] ACPI: Local APIC address 0xfee00000
    [ 0.000000] ACPI: LAPIC (acpi_id[0x01] lapic_id[0x00] enabled)
    [ 0.000000] ACPI: LAPIC (acpi_id[0x02] lapic_id[0x01] enabled)
    [ 0.000000] ACPI: LAPIC (acpi_id[0x03] lapic_id[0x02] enabled)
    [ 0.000000] ACPI: LAPIC (acpi_id[0x04] lapic_id[0x03] enabled)
    [ 0.000000] ACPI: LAPIC (acpi_id[0x05] lapic_id[0x04] enabled)
    [ 0.000000] ACPI: LAPIC (acpi_id[0x06] lapic_id[0x05] enabled)
    [ 0.000000] ACPI: LAPIC (acpi_id[0x07] lapic_id[0x06] enabled)
    [ 0.000000] ACPI: LAPIC (acpi_id[0x08] lapic_id[0x07] enabled)
    [ 0.000000] ACPI: IOAPIC (id[0x02] address[0xfec00000] gsi_base[0])
    [ 0.000000] IOAPIC[0]: apic_id 2, version 32, address 0xfec00000, GSI 0-23
    [ 0.000000] ACPI: INT_SRC_OVR (bus 0 bus_irq 0 global_irq 2 dfl dfl)
    [ 0.000000] ACPI: INT_SRC_OVR (bus 0 bus_irq 9 global_irq 9 high level)
    [ 0.000000] ACPI: IRQ0 used by override.
    [ 0.000000] ACPI: IRQ9 used by override.
    [ 0.000000] Using ACPI (MADT) for SMP configuration information
    [ 0.000000] ACPI: HPET id: 0x8086a201 base: 0xfed00000
    [ 0.000000] smpboot: Allowing 8 CPUs, 0 hotplug CPUs
    [ 0.000000] PM: Registered nosave memory: [mem 0x00000000-0x00000fff]
    [ 0.000000] PM: Registered nosave memory: [mem 0x0006f000-0x0006ffff]
    [ 0.000000] PM: Registered nosave memory: [mem 0x00088000-0x000bffff]
    [ 0.000000] PM: Registered nosave memory: [mem 0x000c0000-0x000fffff]
    [ 0.000000] PM: Registered nosave memory: [mem 0x78e7d000-0x78e7dfff]
    [ 0.000000] PM: Registered nosave memory: [mem 0x78e8d000-0x78e8dfff]
    [ 0.000000] PM: Registered nosave memory: [mem 0x78e8e000-0x78e8efff]
    [ 0.000000] PM: Registered nosave memory: [mem 0x78ea7000-0x78ea7fff]
    [ 0.000000] PM: Registered nosave memory: [mem 0x9c07f000-0x9ce7efff]
    [ 0.000000] PM: Registered nosave memory: [mem 0x9ce7f000-0x9cf7efff]
    [ 0.000000] PM: Registered nosave memory: [mem 0x9cf7f000-0x9cffefff]
    [ 0.000000] PM: Registered nosave memory: [mem 0x9d000000-0x9f9fffff]
    [ 0.000000] PM: Registered nosave memory: [mem 0x9fa00000-0xdfffffff]
    [ 0.000000] PM: Registered nosave memory: [mem 0xe0000000-0xefffffff]
    [ 0.000000] PM: Registered nosave memory: [mem 0xf0000000-0xfeafffff]
    [ 0.000000] PM: Registered nosave memory: [mem 0xfeb00000-0xfeb0ffff]
    [ 0.000000] PM: Registered nosave memory: [mem 0xfeb10000-0xfebfffff]
    [ 0.000000] PM: Registered nosave memory: [mem 0xfec00000-0xfec00fff]
    [ 0.000000] PM: Registered nosave memory: [mem 0xfec01000-0xfecfffff]
    [ 0.000000] PM: Registered nosave memory: [mem 0xfed00000-0xfee00fff]
    [ 0.000000] PM: Registered nosave memory: [mem 0xfee01000-0xffafffff]
    [ 0.000000] PM: Registered nosave memory: [mem 0xffb00000-0xffffffff]
    [ 0.000000] e820: [mem 0x9fa00000-0xdfffffff] available for PCI devices
    [ 0.000000] Booting paravirtualized kernel on bare hardware
    [ 0.000000] setup_percpu: NR_CPUS:128 nr_cpumask_bits:128 nr_cpu_ids:8 nr_node_ids:1
    [ 0.000000] PERCPU: Embedded 30 pages/cpu @ffff88045f200000 s82880 r8192 d31808 u262144
    [ 0.000000] pcpu-alloc: s82880 r8192 d31808 u262144 alloc=1*2097152
    [ 0.000000] pcpu-alloc: [0] 0 1 2 3 4 5 6 7
    [ 0.000000] Built 1 zonelists in Node order, mobility grouping on. Total pages: 4110103
    [ 0.000000] Policy zone: Normal
    [ 0.000000] Kernel command line: initrd=\initramfs-linux.img root=/dev/mapper/VolGroup00-lv_root rw
    [ 0.000000] PID hash table entries: 4096 (order: 3, 32768 bytes)
    [ 0.000000] xsave: enabled xstate_bv 0x7, cntxt size 0x340 using standard form
    [ 0.000000] AGP: Checking aperture...
    [ 0.000000] AGP: No AGP bridge found
    [ 0.000000] Calgary: detecting Calgary via BIOS EBDA area
    [ 0.000000] Calgary: Unable to locate Rio Grande table in EBDA - bailing!
    [ 0.000000] Memory: 16285004K/16701464K available (5481K kernel code, 908K rwdata, 1720K rodata, 1160K init, 1184K bss, 416460K reserved)
    [ 0.000000] SLUB: HWalign=64, Order=0-3, MinObjects=0, CPUs=8, Nodes=1
    [ 0.000000] Preemptible hierarchical RCU implementation.
    [ 0.000000] RCU dyntick-idle grace-period acceleration is enabled.
    [ 0.000000] Dump stacks of tasks blocking RCU-preempt GP.
    [ 0.000000] RCU restricting CPUs from NR_CPUS=128 to nr_cpu_ids=8.
    [ 0.000000] RCU: Adjusting geometry for rcu_fanout_leaf=16, nr_cpu_ids=8
    [ 0.000000] NR_IRQS:8448 nr_irqs:488 0
    [ 0.000000] Console: colour dummy device 80x25
    [ 0.000000] console [tty0] enabled
    [ 0.000000] allocated 67108864 bytes of page_cgroup
    [ 0.000000] please try 'cgroup_disable=memory' option if you don't want memory cgroups
    [ 0.000000] hpet clockevent registered
    [ 0.000000] tsc: Fast TSC calibration using PIT
    [ 0.000000] tsc: Detected 2494.211 MHz processor
    [ 0.000021] Calibrating delay loop (skipped), value calculated using timer frequency.. 4990.27 BogoMIPS (lpj=8314036)
    [ 0.000023] pid_max: default: 32768 minimum: 301
    [ 0.000028] ACPI: Core revision 20140926
    [ 0.014940] ACPI: All ACPI Tables successfully acquired
    [ 0.048477] Security Framework initialized
    [ 0.048484] Yama: becoming mindful.
    [ 0.049168] Dentry cache hash table entries: 2097152 (order: 12, 16777216 bytes)
    [ 0.051306] Inode-cache hash table entries: 1048576 (order: 11, 8388608 bytes)
    [ 0.052245] Mount-cache hash table entries: 32768 (order: 6, 262144 bytes)
    [ 0.052257] Mountpoint-cache hash table entries: 32768 (order: 6, 262144 bytes)
    [ 0.052448] Initializing cgroup subsys memory
    [ 0.052452] Initializing cgroup subsys devices
    [ 0.052454] Initializing cgroup subsys freezer
    [ 0.052455] Initializing cgroup subsys net_cls
    [ 0.052457] Initializing cgroup subsys blkio
    [ 0.052472] CPU: Physical Processor ID: 0
    [ 0.052473] CPU: Processor Core ID: 0
    [ 0.052476] ENERGY_PERF_BIAS: Set to 'normal', was 'performance'
    ENERGY_PERF_BIAS: View and update with x86_energy_perf_policy(8)
    [ 0.053226] mce: CPU supports 9 MCE banks
    [ 0.053236] CPU0: Thermal monitoring enabled (TM1)
    [ 0.053246] Last level iTLB entries: 4KB 1024, 2MB 1024, 4MB 1024
    Last level dTLB entries: 4KB 1024, 2MB 1024, 4MB 1024, 1GB 4
    [ 0.053323] Freeing SMP alternatives memory: 20K (ffffffff81a07000 - ffffffff81a0c000)
    [ 0.053911] Ignoring BGRT: invalid status 0 (expected 1)
    [ 0.055124] ftrace: allocating 20931 entries in 82 pages
    [ 0.061596] dmar: Host address width 39
    [ 0.061597] dmar: DRHD base: 0x000000fed90000 flags: 0x0
    [ 0.061601] dmar: IOMMU 0: reg_base_addr fed90000 ver 1:0 cap c0000020660462 ecap f0101a
    [ 0.061602] dmar: DRHD base: 0x000000fed91000 flags: 0x1
    [ 0.061605] dmar: IOMMU 1: reg_base_addr fed91000 ver 1:0 cap d2008020660462 ecap f010da
    [ 0.061606] dmar: RMRR base: 0x0000009cd6f000 end: 0x0000009cd8efff
    [ 0.061606] dmar: RMRR base: 0x0000009d800000 end: 0x0000009f9fffff
    [ 0.061670] IOAPIC id 2 under DRHD base 0xfed91000 IOMMU 1
    [ 0.061671] HPET id 0 under DRHD base 0xfed91000
    [ 0.061671] Queued invalidation will be enabled to support x2apic and Intr-remapping.
    [ 0.061783] Enabled IRQ remapping in x2apic mode
    [ 0.061784] Enabling x2apic
    [ 0.061784] Enabled x2apic
    [ 0.061789] Switched APIC routing to cluster x2apic.
    [ 0.062206] ..TIMER: vector=0x30 apic1=0 pin1=2 apic2=-1 pin2=-1
    [ 0.095245] smpboot: CPU0: Intel(R) Core(TM) i7-4710HQ CPU @ 2.50GHz (fam: 06, model: 3c, stepping: 03)
    [ 0.095250] TSC deadline timer enabled
    [ 0.095266] Performance Events: PEBS fmt2+, 16-deep LBR, Haswell events, full-width counters, Intel PMU driver.
    [ 0.095280] ... version: 3
    [ 0.095281] ... bit width: 48
    [ 0.095281] ... generic registers: 4
    [ 0.095282] ... value mask: 0000ffffffffffff
    [ 0.095283] ... max period: 0000ffffffffffff
    [ 0.095283] ... fixed-purpose events: 3
    [ 0.095284] ... event mask: 000000070000000f
    [ 0.118723] x86: Booting SMP configuration:
    [ 0.118724] .... node #0, CPUs: #1
    [ 0.132727] NMI watchdog: enabled on all CPUs, permanently consumes one hw-PMU counter.
    [ 0.139403] #2 #3 #4 #5 #6 #7
    [ 0.253216] x86: Booted up 1 node, 8 CPUs
    [ 0.253219] smpboot: Total of 8 processors activated (39923.18 BogoMIPS)
    [ 0.259240] devtmpfs: initialized
    [ 0.261225] PM: Registering ACPI NVS region [mem 0x9ce7f000-0x9cf7efff] (1048576 bytes)
    [ 0.261788] pinctrl core: initialized pinctrl subsystem
    [ 0.261821] RTC time: 15:05:14, date: 03/07/15
    [ 0.261896] NET: Registered protocol family 16
    [ 0.272461] cpuidle: using governor ladder
    [ 0.285819] cpuidle: using governor menu
    [ 0.285860] ACPI FADT declares the system doesn't support PCIe ASPM, so disable it
    [ 0.285861] ACPI: bus type PCI registered
    [ 0.285863] acpiphp: ACPI Hot Plug PCI Controller Driver version: 0.5
    [ 0.285923] PCI: MMCONFIG for domain 0000 [bus 00-ff] at [mem 0xe0000000-0xefffffff] (base 0xe0000000)
    [ 0.285925] PCI: MMCONFIG at [mem 0xe0000000-0xefffffff] reserved in E820
    [ 0.286198] PCI: Using configuration type 1 for base access
    [ 0.299479] ACPI: Added _OSI(Module Device)
    [ 0.299481] ACPI: Added _OSI(Processor Device)
    [ 0.299482] ACPI: Added _OSI(3.0 _SCP Extensions)
    [ 0.299483] ACPI: Added _OSI(Processor Aggregator Device)
    [ 0.302912] ACPI: Executed 1 blocks of module-level executable AML code
    [ 0.305266] [Firmware Bug]: ACPI: BIOS _OSI(Linux) query ignored
    [ 0.306241] ACPI: Dynamic OEM Table Load:
    [ 0.306250] ACPI: SSDT 0xFFFF880448503800 0003D3 (v01 PmRef Cpu0Cst 00003001 INTL 20131115)
    [ 0.319415] ACPI: Dynamic OEM Table Load:
    [ 0.319425] ACPI: SSDT 0xFFFF8804485D2000 0005AA (v01 PmRef ApIst 00003000 INTL 20131115)
    [ 0.332651] ACPI: Dynamic OEM Table Load:
    [ 0.332660] ACPI: SSDT 0xFFFF88044858EE00 000119 (v01 PmRef ApCst 00003000 INTL 20131115)
    [ 0.384073] ACPI: Interpreter enabled
    [ 0.384081] ACPI Exception: AE_NOT_FOUND, While evaluating Sleep State [\_S1_] (20140926/hwxface-580)
    [ 0.384088] ACPI Exception: AE_NOT_FOUND, While evaluating Sleep State [\_S2_] (20140926/hwxface-580)
    [ 0.384107] ACPI: (supports S0 S3 S4 S5)
    [ 0.384108] ACPI: Using IOAPIC for interrupt routing
    [ 0.384130] PCI: Using host bridge windows from ACPI; if necessary, use "pci=nocrs" and report a bug
    [ 0.388473] ACPI: Power Resource [PG00] (on)
    [ 0.390539] ACPI: PCI Root Bridge [PCI0] (domain 0000 [bus 00-fe])
    [ 0.390543] acpi PNP0A08:00: _OSC: OS supports [ExtendedConfig ASPM ClockPM Segments MSI]
    [ 0.390880] acpi PNP0A08:00: _OSC: OS now controls [PCIeHotplug PME AER PCIeCapability]
    [ 0.391231] PCI host bridge to bus 0000:00
    [ 0.391233] pci_bus 0000:00: root bus resource [bus 00-fe]
    [ 0.391234] pci_bus 0000:00: root bus resource [io 0x0000-0x0cf7]
    [ 0.391236] pci_bus 0000:00: root bus resource [io 0x0d00-0xffff]
    [ 0.391237] pci_bus 0000:00: root bus resource [mem 0x000a0000-0x000bffff]
    [ 0.391237] pci_bus 0000:00: root bus resource [mem 0x000c0000-0x000c3fff]
    [ 0.391238] pci_bus 0000:00: root bus resource [mem 0x000c4000-0x000c7fff]
    [ 0.391239] pci_bus 0000:00: root bus resource [mem 0x000c8000-0x000cbfff]
    [ 0.391240] pci_bus 0000:00: root bus resource [mem 0x000cc000-0x000cffff]
    [ 0.391241] pci_bus 0000:00: root bus resource [mem 0x000d0000-0x000d3fff]
    [ 0.391242] pci_bus 0000:00: root bus resource [mem 0x000d4000-0x000d7fff]
    [ 0.391243] pci_bus 0000:00: root bus resource [mem 0x000d8000-0x000dbfff]
    [ 0.391244] pci_bus 0000:00: root bus resource [mem 0x000dc000-0x000dffff]
    [ 0.391245] pci_bus 0000:00: root bus resource [mem 0x000e0000-0x000e3fff]
    [ 0.391246] pci_bus 0000:00: root bus resource [mem 0x000e4000-0x000e7fff]
    [ 0.391247] pci_bus 0000:00: root bus resource [mem 0x000e8000-0x000ebfff]
    [ 0.391248] pci_bus 0000:00: root bus resource [mem 0x000ec000-0x000effff]
    [ 0.391248] pci_bus 0000:00: root bus resource [mem 0x000f0000-0x000fffff]
    [ 0.391249] pci_bus 0000:00: root bus resource [mem 0x9fa00000-0xfeafffff]
    [ 0.391255] pci 0000:00:00.0: [8086:0c04] type 00 class 0x060000
    [ 0.391363] pci 0000:00:01.0: [8086:0c01] type 01 class 0x060400
    [ 0.391390] pci 0000:00:01.0: PME# supported from D0 D3hot D3cold
    [ 0.391467] pci 0000:00:01.0: System wakeup disabled by ACPI
    [ 0.391495] pci 0000:00:02.0: [8086:0416] type 00 class 0x030000
    [ 0.391503] pci 0000:00:02.0: reg 0x10: [mem 0xd1000000-0xd13fffff 64bit]
    [ 0.391507] pci 0000:00:02.0: reg 0x18: [mem 0xc0000000-0xcfffffff 64bit pref]
    [ 0.391511] pci 0000:00:02.0: reg 0x20: [io 0x4000-0x403f]
    [ 0.391611] pci 0000:00:03.0: [8086:0c0c] type 00 class 0x040300
    [ 0.391617] pci 0000:00:03.0: reg 0x10: [mem 0xd1710000-0xd1713fff 64bit]
    [ 0.391739] pci 0000:00:14.0: [8086:8c31] type 00 class 0x0c0330
    [ 0.391754] pci 0000:00:14.0: reg 0x10: [mem 0xd1700000-0xd170ffff 64bit]
    [ 0.391806] pci 0000:00:14.0: PME# supported from D3hot D3cold
    [ 0.391878] pci 0000:00:14.0: System wakeup disabled by ACPI
    [ 0.391904] pci 0000:00:16.0: [8086:8c3a] type 00 class 0x078000
    [ 0.391922] pci 0000:00:16.0: reg 0x10: [mem 0xd1718000-0xd171800f 64bit]
    [ 0.391977] pci 0000:00:16.0: PME# supported from D0 D3hot D3cold
    [ 0.392081] pci 0000:00:1b.0: [8086:8c20] type 00 class 0x040300
    [ 0.392094] pci 0000:00:1b.0: reg 0x10: [mem 0xd1714000-0xd1717fff 64bit]
    [ 0.392153] pci 0000:00:1b.0: PME# supported from D0 D3hot D3cold
    [ 0.392226] pci 0000:00:1b.0: System wakeup disabled by ACPI
    [ 0.392251] pci 0000:00:1c.0: [8086:8c10] type 01 class 0x060400
    [ 0.392316] pci 0000:00:1c.0: PME# supported from D0 D3hot D3cold
    [ 0.392392] pci 0000:00:1c.0: System wakeup disabled by ACPI
    [ 0.392418] pci 0000:00:1c.4: [8086:8c18] type 01 class 0x060400
    [ 0.392477] pci 0000:00:1c.4: PME# supported from D0 D3hot D3cold
    [ 0.392552] pci 0000:00:1c.4: System wakeup disabled by ACPI
    [ 0.392576] pci 0000:00:1c.5: [8086:8c1a] type 01 class 0x060400
    [ 0.392635] pci 0000:00:1c.5: PME# supported from D0 D3hot D3cold
    [ 0.392713] pci 0000:00:1c.5: System wakeup disabled by ACPI
    [ 0.392742] pci 0000:00:1f.0: [8086:8c4b] type 00 class 0x060100
    [ 0.392924] pci 0000:00:1f.2: [8086:8c03] type 00 class 0x010601
    [ 0.392937] pci 0000:00:1f.2: reg 0x10: [io 0x4088-0x408f]
    [ 0.392943] pci 0000:00:1f.2: reg 0x14: [io 0x4094-0x4097]
    [ 0.392950] pci 0000:00:1f.2: reg 0x18: [io 0x4080-0x4087]
    [ 0.392956] pci 0000:00:1f.2: reg 0x1c: [io 0x4090-0x4093]
    [ 0.392962] pci 0000:00:1f.2: reg 0x20: [io 0x4060-0x407f]
    [ 0.392968] pci 0000:00:1f.2: reg 0x24: [mem 0xd171b000-0xd171b7ff]
    [ 0.393001] pci 0000:00:1f.2: PME# supported from D3hot
    [ 0.393092] pci 0000:00:1f.3: [8086:8c22] type 00 class 0x0c0500
    [ 0.393105] pci 0000:00:1f.3: reg 0x10: [mem 0xd1719000-0xd17190ff 64bit]
    [ 0.393121] pci 0000:00:1f.3: reg 0x20: [io 0x4040-0x405f]
    [ 0.393269] pci 0000:01:00.0: [10de:1392] type 00 class 0x030200
    [ 0.393285] pci 0000:01:00.0: reg 0x10: [mem 0xd0000000-0xd0ffffff]
    [ 0.393301] pci 0000:01:00.0: reg 0x14: [mem 0xa0000000-0xafffffff 64bit pref]
    [ 0.393317] pci 0000:01:00.0: reg 0x1c: [mem 0xb0000000-0xb1ffffff 64bit pref]
    [ 0.393328] pci 0000:01:00.0: reg 0x24: [io 0x3000-0x307f]
    [ 0.393338] pci 0000:01:00.0: reg 0x30: [mem 0xfff80000-0xffffffff pref]
    [ 0.393417] pci 0000:01:00.0: System wakeup disabled by ACPI
    [ 0.399365] pci 0000:00:01.0: PCI bridge to [bus 01-06]
    [ 0.399367] pci 0000:00:01.0: bridge window [io 0x3000-0x3fff]
    [ 0.399370] pci 0000:00:01.0: bridge window [mem 0xd0000000-0xd0ffffff]
    [ 0.399373] pci 0000:00:01.0: bridge window [mem 0xa0000000-0xbfffffff 64bit pref]
    [ 0.399511] pci 0000:07:00.0: [144d:a800] type 00 class 0x010601
    [ 0.399581] pci 0000:07:00.0: reg 0x24: [mem 0xd1600000-0xd1601fff]
    [ 0.399611] pci 0000:07:00.0: reg 0x30: [mem 0xffff0000-0xffffffff pref]
    [ 0.399698] pci 0000:07:00.0: PME# supported from D3hot D3cold
    [ 0.399751] pci 0000:07:00.0: System wakeup disabled by ACPI
    [ 0.406055] pci 0000:00:1c.0: PCI bridge to [bus 07]
    [ 0.406061] pci 0000:00:1c.0: bridge window [mem 0xd1600000-0xd16fffff]
    [ 0.406133] pci 0000:08:00.0: [10ec:5227] type 00 class 0xff0000
    [ 0.406153] pci 0000:08:00.0: reg 0x10: [mem 0xd1500000-0xd1500fff]
    [ 0.406285] pci 0000:08:00.0: supports D1 D2
    [ 0.406286] pci 0000:08:00.0: PME# supported from D1 D2 D3hot D3cold
    [ 0.406316] pci 0000:08:00.0: System wakeup disabled by ACPI
    [ 0.412720] pci 0000:00:1c.4: PCI bridge to [bus 08]
    [ 0.412725] pci 0000:00:1c.4: bridge window [mem 0xd1500000-0xd15fffff]
    [ 0.412836] pci 0000:09:00.0: [8086:08b1] type 00 class 0x028000
    [ 0.412890] pci 0000:09:00.0: reg 0x10: [mem 0xd1400000-0xd1401fff 64bit]
    [ 0.413128] pci 0000:09:00.0: PME# supported from D0 D3hot D3cold
    [ 0.413183] pci 0000:09:00.0: System wakeup disabled by ACPI
    [ 0.419415] pci 0000:00:1c.5: PCI bridge to [bus 09]
    [ 0.419420] pci 0000:00:1c.5: bridge window [mem 0xd1400000-0xd14fffff]
    [ 0.419464] acpi PNP0A08:00: Disabling ASPM (FADT indicates it is unsupported)
    [ 0.420118] ACPI: PCI Interrupt Link [LNKA] (IRQs 3 4 5 6 10 11 12 14 15) *0, disabled.
    [ 0.420157] ACPI: PCI Interrupt Link [LNKB] (IRQs 3 4 5 6 10 11 12 14 15) *0, disabled.
    [ 0.420195] ACPI: PCI Interrupt Link [LNKC] (IRQs 3 4 5 6 10 11 12 14 15) *0, disabled.
    [ 0.420233] ACPI: PCI Interrupt Link [LNKD] (IRQs 3 4 5 6 10 11 12 14 15) *0, disabled.
    [ 0.420269] ACPI: PCI Interrupt Link [LNKE] (IRQs 3 4 5 6 10 11 12 14 15) *0, disabled.
    [ 0.420305] ACPI: PCI Interrupt Link [LNKF] (IRQs 3 4 5 6 10 11 12 14 15) *0, disabled.
    [ 0.420341] ACPI: PCI Interrupt Link [LNKG] (IRQs 3 4 5 6 10 11 12 14 15) *0, disabled.
    [ 0.420377] ACPI: PCI Interrupt Link [LNKH] (IRQs 3 4 5 6 10 11 12 14 15) *0, disabled.
    [ 0.420652] ACPI: Enabled 6 GPEs in block 00 to 3F
    [ 0.420689] ACPI : EC: GPE = 0x17, I/O: command/status = 0x66, data = 0x62
    [ 0.420760] vgaarb: setting as boot device: PCI:0000:00:02.0
    [ 0.420762] vgaarb: device added: PCI:0000:00:02.0,decodes=io+mem,owns=io+mem,locks=none
    [ 0.420764] vgaarb: loaded
    [ 0.420765] vgaarb: bridge control possible 0000:00:02.0
    [ 0.420853] PCI: Using ACPI for IRQ routing
    [ 0.425911] PCI: pci_cache_line_size set to 64 bytes
    [ 0.425949] e820: reserve RAM buffer [mem 0x0006f000-0x0006ffff]
    [ 0.425950] e820: reserve RAM buffer [mem 0x00088000-0x0008ffff]
    [ 0.425951] e820: reserve RAM buffer [mem 0x78e7d018-0x7bffffff]
    [ 0.425952] e820: reserve RAM buffer [mem 0x78e8e018-0x7bffffff]
    [ 0.425953] e820: reserve RAM buffer [mem 0x9c07f000-0x9fffffff]
    [ 0.425954] e820: reserve RAM buffer [mem 0x9d000000-0x9fffffff]
    [ 0.425955] e820: reserve RAM buffer [mem 0x45f600000-0x45fffffff]
    [ 0.426019] NetLabel: Initializing
    [ 0.426020] NetLabel: domain hash size = 128
    [ 0.426021] NetLabel: protocols = UNLABELED CIPSOv4
    [ 0.426028] NetLabel: unlabeled traffic allowed by default
    [ 0.426041] hpet0: at MMIO 0xfed00000, IRQs 2, 8, 0, 0, 0, 0, 0, 0
    [ 0.426044] hpet0: 8 comparators, 64-bit 14.318180 MHz counter
    [ 0.428075] Switched to clocksource hpet
    [ 0.431534] pnp: PnP ACPI init
    [ 0.431620] system 00:00: [io 0x0680-0x069f] has been reserved
    [ 0.431622] system 00:00: [io 0xffff] has been reserved
    [ 0.431623] system 00:00: [io 0xffff] has been reserved
    [ 0.431624] system 00:00: [io 0xffff] has been reserved
    [ 0.431625] system 00:00: [io 0x1800-0x18fe] could not be reserved
    [ 0.431626] system 00:00: [io 0x164e-0x164f] has been reserved
    [ 0.431628] system 00:00: Plug and Play ACPI device, IDs PNP0c02 (active)
    [ 0.431656] system 00:01: [io 0x0800-0x087f] has been reserved
    [ 0.431658] system 00:01: Plug and Play ACPI device, IDs PNP0c02 (active)
    [ 0.431677] pnp 00:02: Plug and Play ACPI device, IDs PNP0b00 (active)
    [ 0.431703] system 00:03: [io 0x1854-0x1857] has been reserved
    [ 0.431705] system 00:03: Plug and Play ACPI device, IDs INT3f0d PNP0c02 (active)
    [ 0.431750] pnp 00:04: Plug and Play ACPI device, IDs HPQ8001 PNP0303 (active)
    [ 0.431766] pnp 00:05: Plug and Play ACPI device, IDs SYN1ed8 SYN1e00 SYN0002 PNP0f13 (active)
    [ 0.431848] system 00:06: [mem 0xfed1c000-0xfed1ffff] has been reserved
    [ 0.431849] system 00:06: [mem 0xfed10000-0xfed17fff] has been reserved
    [ 0.431850] system 00:06: [mem 0xfed18000-0xfed18fff] has been reserved
    [ 0.431852] system 00:06: [mem 0xfed19000-0xfed19fff] has been reserved
    [ 0.431853] system 00:06: [mem 0xe0000000-0xefffffff] has been reserved
    [ 0.431854] system 00:06: [mem 0xfed20000-0xfed3ffff] has been reserved
    [ 0.431855] system 00:06: [mem 0xfed90000-0xfed93fff] could not be reserved
    [ 0.431856] system 00:06: [mem 0xff000000-0xffffffff] could not be reserved
    [ 0.431857] system 00:06: [mem 0xfee00000-0xfeefffff] could not be reserved
    [ 0.431858] system 00:06: [mem 0x9fa20000-0x9fa20fff] has been reserved
    [ 0.431860] system 00:06: [mem 0x9fa10000-0x9fa1ffff] has been reserved
    [ 0.431861] system 00:06: Plug and Play ACPI device, IDs PNP0c02 (active)
    [ 0.432212] pnp: PnP ACPI: found 7 devices
    [ 0.438072] pci 0000:01:00.0: can't claim BAR 6 [mem 0xfff80000-0xffffffff pref]: no compatible bridge window
    [ 0.438074] pci 0000:07:00.0: can't claim BAR 6 [mem 0xffff0000-0xffffffff pref]: no compatible bridge window
    [ 0.438102] pci 0000:01:00.0: BAR 6: assigned [mem 0xb2000000-0xb207ffff pref]
    [ 0.438103] pci 0000:00:01.0: PCI bridge to [bus 01-06]
    [ 0.438105] pci 0000:00:01.0: bridge window [io 0x3000-0x3fff]
    [ 0.438107] pci 0000:00:01.0: bridge window [mem 0xd0000000-0xd0ffffff]
    [ 0.438109] pci 0000:00:01.0: bridge window [mem 0xa0000000-0xbfffffff 64bit pref]
    [ 0.438112] pci 0000:07:00.0: BAR 6: assigned [mem 0xd1610000-0xd161ffff pref]
    [ 0.438113] pci 0000:00:1c.0: PCI bridge to [bus 07]
    [ 0.438117] pci 0000:00:1c.0: bridge window [mem 0xd1600000-0xd16fffff]
    [ 0.438123] pci 0000:00:1c.4: PCI bridge to [bus 08]
    [ 0.438127] pci 0000:00:1c.4: bridge window [mem 0xd1500000-0xd15fffff]
    [ 0.438133] pci 0000:00:1c.5: PCI bridge to [bus 09]
    [ 0.438137] pci 0000:00:1c.5: bridge window [mem 0xd1400000-0xd14fffff]
    [ 0.438143] pci_bus 0000:00: resource 4 [io 0x0000-0x0cf7]
    [ 0.438144] pci_bus 0000:00: resource 5 [io 0x0d00-0xffff]
    [ 0.438145] pci_bus 0000:00: resource 6 [mem 0x000a0000-0x000bffff]
    [ 0.438146] pci_bus 0000:00: resource 7 [mem 0x000c0000-0x000c3fff]
    [ 0.438147] pci_bus 0000:00: resource 8 [mem 0x000c4000-0x000c7fff]
    [ 0.438148] pci_bus 0000:00: resource 9 [mem 0x000c8000-0x000cbfff]
    [ 0.438149] pci_bus 0000:00: resource 10 [mem 0x000cc000-0x000cffff]
    [ 0.438150] pci_bus 0000:00: resource 11 [mem 0x000d0000-0x000d3fff]
    [ 0.438151] pci_bus 0000:00: resource 12 [mem 0x000d4000-0x000d7fff]
    [ 0.438152] pci_bus 0000:00: resource 13 [mem 0x000d8000-0x000dbfff]
    [ 0.438153] pci_bus 0000:00: resource 14 [mem 0x000dc000-0x000dffff]
    [ 0.438154] pci_bus 0000:00: resource 15 [mem 0x000e0000-0x000e3fff]
    [ 0.438155] pci_bus 0000:00: resource 16 [mem 0x000e4000-0x000e7fff]
    [ 0.438156] pci_bus 0000:00: resource 17 [mem 0x000e8000-0x000ebfff]
    [ 0.438157] pci_bus 0000:00: resource 18 [mem 0x000ec000-0x000effff]
    [ 0.438158] pci_bus 0000:00: resource 19 [mem 0x000f0000-0x000fffff]
    [ 0.438159] pci_bus 0000:00: resource 20 [mem 0x9fa00000-0xfeafffff]
    [ 0.438160] pci_bus 0000:01: resource 0 [io 0x3000-0x3fff]
    [ 0.438161] pci_bus 0000:01: resource 1 [mem 0xd0000000-0xd0ffffff]
    [ 0.438161] pci_bus 0000:01: resource 2 [mem 0xa0000000-0xbfffffff 64bit pref]
    [ 0.438163] pci_bus 0000:07: resource 1 [mem 0xd1600000-0xd16fffff]
    [ 0.438164] pci_bus 0000:08: resource 1 [mem 0xd1500000-0xd15fffff]
    [ 0.438165] pci_bus 0000:09: resource 1 [mem 0xd1400000-0xd14fffff]
    [ 0.438182] NET: Registered protocol family 2
    [ 0.438329] TCP established hash table entries: 131072 (order: 8, 1048576 bytes)
    [ 0.438470] TCP bind hash table entries: 65536 (order: 8, 1048576 bytes)
    [ 0.438574] TCP: Hash tables configured (established 131072 bind 65536)
    [ 0.438585] TCP: reno registered
    [ 0.438597] UDP hash table entries: 8192 (order: 6, 262144 bytes)
    [ 0.438635] UDP-Lite hash table entries: 8192 (order: 6, 262144 bytes)
    [ 0.438690] NET: Registered protocol family 1
    [ 0.438701] pci 0000:00:02.0: Video device with shadowed ROM
    [ 0.440063] PCI: CLS 64 bytes, default 64
    [ 0.440092] Unpacking initramfs...
    [ 0.535471] Freeing initrd memory: 8480K (ffff88007f7d2000 - ffff88008001a000)
    [ 0.535494] PCI-DMA: Using software bounce buffering for IO (SWIOTLB)
    [ 0.535496] software IO TLB [mem 0x97c0e000-0x9bc0e000] (64MB) mapped at [ffff880097c0e000-ffff88009bc0dfff]
    [ 0.535525] Simple Boot Flag at 0x44 set to 0x1
    [ 0.535703] RAPL PMU detected, hw unit 2^-14 Joules, API unit is 2^-32 Joules, 4 fixed counters 655360 ms ovfl timer
    [ 0.535742] microcode: CPU0 sig=0x306c3, pf=0x20, revision=0x1c
    [ 0.535747] microcode: CPU1 sig=0x306c3, pf=0x20, revision=0x1c
    [ 0.535753] microcode: CPU2 sig=0x306c3, pf=0x20, revision=0x1c
    [ 0.535759] microcode: CPU3 sig=0x306c3, pf=0x20, revision=0x1c
    [ 0.535764] microcode: CPU4 sig=0x306c3, pf=0x20, revision=0x1c
    [ 0.535770] microcode: CPU5 sig=0x306c3, pf=0x20, revision=0x1c
    [ 0.535775] microcode: CPU6 sig=0x306c3, pf=0x20, revision=0x1c
    [ 0.535781] microcode: CPU7 sig=0x306c3, pf=0x20, revision=0x1c
    [ 0.535821] microcode: Microcode Update Driver: v2.00 <[email protected]>, Peter Oruba
    [ 0.535836] Scanning for low memory corruption every 60 seconds
    [ 0.536021] futex hash table entries: 2048 (order: 5, 131072 bytes)
    [ 0.536041] Initialise system trusted keyring
    [ 0.536249] HugeTLB registered 2 MB page size, pre-allocated 0 pages
    [ 0.537029] zpool: loaded
    [ 0.537031] zbud: loaded
    [ 0.537161] VFS: Disk quotas dquot_6.5.2
    [ 0.537181] Dquot-cache hash table entries: 512 (order 0, 4096 bytes)
    [ 0.537256] msgmni has been set to 31953
    [ 0.537287] Key type big_key registered
    [ 0.537431] Block layer SCSI generic (bsg) driver version 0.4 loaded (major 252)
    [ 0.537471] io scheduler noop registered
    [ 0.537473] io scheduler deadline registered
    [ 0.537490] io scheduler cfq registered (default)
    [ 0.537616] pcieport 0000:00:01.0: irq 26 for MSI/MSI-X
    [ 0.537711] pcieport 0000:00:1c.0: irq 27 for MSI/MSI-X
    [ 0.537809] pcieport 0000:00:1c.4: irq 28 for MSI/MSI-X
    [ 0.537906] pcieport 0000:00:1c.5: irq 29 for MSI/MSI-X
    [ 0.537967] pcieport 0000:00:01.0: Signaling PME through PCIe PME interrupt
    [ 0.537968] pci 0000:01:00.0: Signaling PME through PCIe PME interrupt
    [ 0.537970] pcie_pme 0000:00:01.0:pcie01: service driver pcie_pme loaded
    [ 0.537981] pcieport 0000:00:1c.0: Signaling PME through PCIe PME interrupt
    [ 0.537982] pci 0000:07:00.0: Signaling PME through PCIe PME interrupt
    [ 0.537986] pcie_pme 0000:00:1c.0:pcie01: service driver pcie_pme loaded
    [ 0.537996] pcieport 0000:00:1c.4: Signaling PME through PCIe PME interrupt
    [ 0.537997] pci 0000:08:00.0: Signaling PME through PCIe PME interrupt
    [ 0.538000] pcie_pme 0000:00:1c.4:pcie01: service driver pcie_pme loaded
    [ 0.538010] pcieport 0000:00:1c.5: Signaling PME through PCIe PME interrupt
    [ 0.538011] pci 0000:09:00.0: Signaling PME through PCIe PME interrupt
    [ 0.538014] pcie_pme 0000:00:1c.5:pcie01: service driver pcie_pme loaded
    [ 0.538023] pci_hotplug: PCI Hot Plug PCI Core version: 0.5
    [ 0.538035] pciehp: PCI Express Hot Plug Controller Driver version: 0.4
    [ 0.538055] efifb: probing for efifb
    [ 0.538070] efifb: framebuffer at 0xc0000000, mapped to 0xffffc90011c00000, using 8100k, total 8100k
    [ 0.538071] efifb: mode is 1920x1080x32, linelength=7680, pages=1
    [ 0.538071] efifb: scrolling: redraw
    [ 0.538072] efifb: Truecolor: size=8:8:8:8, shift=24:16:8:0
    [ 0.541482] Console: switching to colour frame buffer device 240x67
    [ 0.544794] fb0: EFI VGA frame buffer device
    [ 0.544800] intel_idle: MWAIT substates: 0x42120
    [ 0.544801] intel_idle: v0.4 model 0x3C
    [ 0.544801] intel_idle: lapic_timer_reliable_states 0xffffffff
    [ 0.545023] GHES: HEST is not enabled!
    [ 0.545063] Serial: 8250/16550 driver, 4 ports, IRQ sharing disabled
    [ 0.545351] Linux agpgart interface v0.103
    [ 0.545389] rtc_cmos 00:02: RTC can wake from S4
    [ 0.545490] rtc_cmos 00:02: rtc core: registered rtc_cmos as rtc0
    [ 0.545516] rtc_cmos 00:02: alarms up to one month, 242 bytes nvram, hpet irqs
    [ 0.545524] Intel P-state driver initializing.
    [ 0.545680] ledtrig-cpu: registered to indicate activity on CPUs
    [ 0.545994] TCP: cubic registered
    [ 0.546216] NET: Registered protocol family 10
    [ 0.546732] NET: Registered protocol family 17
    [ 0.547560] Loading compiled-in X.509 certificates
    [ 0.547591] registered taskstats version 1
    [ 0.548780] Magic number: 7:609:82
    [ 0.548952] rtc_cmos 00:02: setting system clock to 2015-03-07 15:05:15 UTC (1425740715)
    [ 0.549136] PM: Hibernation image not present or could not be loaded.
    [ 0.551123] Freeing unused kernel memory: 1160K (ffffffff818e5000 - ffffffff81a07000)
    [ 0.551126] Write protecting the kernel read-only data: 8192k
    [ 0.555482] Freeing unused kernel memory: 652K (ffff88000155d000 - ffff880001600000)
    [ 0.557272] Freeing unused kernel memory: 328K (ffff8800017ae000 - ffff880001800000)
    [ 0.570421] random: systemd-tmpfile urandom read with 5 bits of entropy available
    [ 0.584356] device-mapper: uevent: version 1.0.3
    [ 0.584470] device-mapper: ioctl: 4.28.0-ioctl (2014-09-17) initialised: [email protected]
    [ 0.597541] i8042: PNP: PS/2 Controller [PNP0303:KBD0,PNP0f13:PS2M] at 0x60,0x64 irq 1,12
    [ 0.602695] serio: i8042 KBD port at 0x60,0x64 irq 1
    [ 0.602710] serio: i8042 AUX port at 0x60,0x64 irq 12
    [ 0.603099] rtsx_pci 0000:08:00.0: irq 30 for MSI/MSI-X
    [ 0.603111] rtsx_pci 0000:08:00.0: rtsx_pci_acquire_irq: pcr->msi_en = 1, pci->irq = 30
    [ 0.604239] ACPI: bus type USB registered
    [ 0.604267] usbcore: registered new interface driver usbfs
    [ 0.604273] SCSI subsystem initialized
    [ 0.604279] usbcore: registered new interface driver hub
    [ 0.604330] usbcore: registered new device driver usb
    [ 0.605601] libata version 3.00 loaded.
    [ 0.605678] xhci_hcd 0000:00:14.0: xHCI Host Controller
    [ 0.605685] xhci_hcd 0000:00:14.0: new USB bus registered, assigned bus number 1
    [ 0.605779] xhci_hcd 0000:00:14.0: cache line size of 64 is not supported
    [ 0.605808] xhci_hcd 0000:00:14.0: irq 31 for MSI/MSI-X
    [ 0.606024] hub 1-0:1.0: USB hub found
    [ 0.606063] hub 1-0:1.0: 14 ports detected
    [ 0.609623] xhci_hcd 0000:00:14.0: xHCI Host Controller
    [ 0.609626] xhci_hcd 0000:00:14.0: new USB bus registered, assigned bus number 2
    [ 0.609780] hub 2-0:1.0: USB hub found
    [ 0.609795] hub 2-0:1.0: 6 ports detected
    [ 0.610944] ahci 0000:00:1f.2: version 3.0
    [ 0.611066] ahci 0000:00:1f.2: irq 32 for MSI/MSI-X
    [ 0.611083] ahci 0000:00:1f.2: SSS flag set, parallel bus scan disabled
    [ 0.611102] ahci 0000:00:1f.2: AHCI 0001.0300 32 slots 4 ports 6 Gbps 0x1 impl SATA mode
    [ 0.611105] ahci 0000:00:1f.2: flags: 64bit ncq stag pm led clo pio slum part ems sxs apst
    [ 0.611516] scsi host0: ahci
    [ 0.611639] scsi host1: ahci
    [ 0.611727] scsi host2: ahci
    [ 0.611822] scsi host3: ahci
    [ 0.611861] ata1: SATA max UDMA/133 abar m2048@0xd171b000 port 0xd171b100 irq 32
    [ 0.611863] ata2: DUMMY
    [ 0.611864] ata3: DUMMY
    [ 0.611865] ata4: DUMMY
    [ 0.621966] input: AT Translated Set 2 keyboard as /devices/platform/i8042/serio0/input/input0
    [ 0.624998] ahci 0000:07:00.0: AHCI 0001.0300 32 slots 1 ports 6 Gbps 0x1 impl SATA mode
    [ 0.625001] ahci 0000:07:00.0: flags: 64bit ncq led clo only pio ccc
    [ 0.625238] scsi host4: ahci
    [ 0.625288] ata5: SATA max UDMA/133 abar m8192@0xd1600000 port 0xd1600100 irq 16
    [ 0.808604] xhci_hcd 0000:00:14.0: Error while assigning device slot ID
    [ 0.808642] xhci_hcd 0000:00:14.0: Max number of devices this xHCI host supports is 32.
    [ 0.808673] usb usb2-port2: couldn't allocate usb_device
    [ 0.808738] xhci_hcd 0000:00:14.0: Error while assigning device slot ID
    [ 0.808768] xhci_hcd 0000:00:14.0: Max number of devices this xHCI host supports is 32.
    [ 0.808798] usb usb2-port6: couldn't allocate usb_device
    [ 0.932036] ata1: SATA link down (SStatus 0 SControl 300)
    [ 0.952070] ata5: SATA link up 6.0 Gbps (SStatus 133 SControl 300)
    [ 0.952367] ata5.00: ATA-9: SAMSUNG MZHPU512HCGL-000H1, UXM62H1Q, max UDMA/133
    [ 0.952370] ata5.00: 1000215216 sectors, multi 16: LBA48 NCQ (depth 31/32), AA
    [ 0.952660] ata5.00: configured for UDMA/133
    [ 0.952785] scsi 4:0:0:0: Direct-Access ATA SAMSUNG MZHPU512 2H1Q PQ: 0 ANSI: 5
    [ 0.955003] sd 4:0:0:0: [sda] 1000215216 512-byte logical blocks: (512 GB/476 GiB)
    [ 0.955028] sd 4:0:0:0: [sda] Write Protect is off
    [ 0.955030] sd 4:0:0:0: [sda] Mode Sense: 00 3a 00 00
    [ 0.955038] sd 4:0:0:0: [sda] Write cache: enabled, read cache: enabled, doesn't support DPO or FUA
    [ 0.956407] sda: sda1 sda2 sda3 sda4 sda5
    [ 0.956825] sd 4:0:0:0: [sda] Attached SCSI disk
    [ 0.968695] usb 1-3: new full-speed USB device number 2 using xhci_hcd
    [ 1.302451] usb 1-4: new high-speed USB device number 3 using xhci_hcd
    [ 1.539371] tsc: Refined TSC clocksource calibration: 2494.224 MHz
    [ 1.646163] usb 1-13: new full-speed USB device number 4 using xhci_hcd
    [ 1.718430] EXT4-fs (dm-1): mounted filesystem with ordered data mode. Opts: (null)
    [ 1.821454] usb 1-13: ep 0x2 - rounding interval to 64 microframes, ep desc says 80 microframes
    [ 1.972758] systemd[1]: systemd 218 running in system mode. (+PAM -AUDIT -SELINUX -IMA -APPARMOR +SMACK -SYSVINIT +UTMP +LIBCRYPTSETUP +GCRYPT +GNUTLS +ACL +XZ +LZ4 +SECCOMP +BLKID -ELFUTILS +KMOD +IDN)
    [ 1.972914] systemd[1]: Detected architecture 'x86-64'.
    [ 1.973342] systemd[1]: Set hostname to <hp_arch>.
    [ 2.046

    Sorry should have mentioned that. Yeah I tried that and it delays the error message a little bit (about 20 seconds after boot vs instantly). In the end it leads to the exact same error though.

  • BSOD ha20x2k.sys.. help from

    IRQ_LESS_OR_EQUAL
    that happened after playing starship troopers for a while....
    i got latest firmware and drivers for everything..
    AMD Athlon 64 X2 4400++ABIT Fatalty AN8-SLI2x XFX 7800GTX Extreme Gamers Edition in SLISound Blaster X-FI Fatalty FPSOCZ EL DDR PC-3500 Gold GX Dual ChannelEnermax EG70AX-VE(W)SFMA 600W ATX V2.00

    Have you done any other troubleshooting on the system yet? If so, perhaps post up some quick detail on what you've tried.
    For instance, it could help to move the card to another PCI slot, as that will make sure it's assigned other resources (like a different IRQ). Don't put it in the slot directly nexto the graphics card, if you can avoid it.
    Are all the latest system updates (where available) loaded aswell?
    Cat

  • HELP! k7t266 pro2-u winxp install

    Hi,
    I have a problem with installation of winXP SP1 on my computer. First i got a blue screen in the first step of installation (windows loads drivers, then freezes).  It said that acpi.sys is the problem. I disabled it and then the problem was irq not less... . Then i disabled
    internal cache,  system bios cacheable and shadowing options and installation started but the computer was too slow ( it took about an hour to copy the files on hard disk). After the installation was finished i put back the fields internal cache to writeback and c00 32k shadow to cached and left system bios cacheable on disabled ( i read in the manual that it might be a reason for system hangups) to speed it up.  For a while it seemed like it was working ok, i installed the drivers, software... but  tomorrow everything up. windows started to freeze when i tried to encode mp3's from audio cd's, when i tried to install new sofware...
    I dont know what to do and don't want to disable   internal cache because of the huge system slowdown...
    Can anyone help !!!
    my config is
    amd athlon xp 1800+
    microstar  k7t266 pro2-u with lan
    256mb kingston 266 ddr
    maxtor 40gb ata133
    teac w540e writer
    nvidia g-force 2 mx400 64mb

    Quote
    Hi!
    What can your PSU provide in terms of ampères?
    Load BIOS setup defaults. Open case.
    Have the HDD and the CDRW on different IDE channels and cables, with both as Master respectively at the end of the cable.
    Install VIA 4in1 drivers.
    When everything works, make proper BIOS adjustments.
    Best wishes, and good night!
    Can't provide the data about my PSU because i'm not at home right now.
    I will do it tomorow.
    Cables are already set up like that.
    Thank you

  • Why is PS CC2014 crashing all the time? Can anyone with experience help?

    Hi there
    I have had relentless problems with all versions of PS CC and PS CC 2014. It crashes almost every time I use it. Some days I get away with it, but mostly I don't. It is basically becoming unusable which is a nightmare because I rely on it for my work. I lose time and work frequently. I have to manually save my files every few minutes for fear of losing everything. A classic cause of it crashing is just opening a file, grabbing a folder of layers, holding down shift to restrain vertical / horizontal direction and dragging with the move tool to reposition in the document. Bam, APPCRASH. A typical fault message is this, which I just generated now, by doing just that:
    Problem signature:
      Problem Event Name:    APPCRASH
      Application Name:    Photoshop.exe
      Application Version:    15.2.0.236
      Application Timestamp:    542531ba
      Fault Module Name:    ntdll.dll
      Fault Module Version:    6.1.7601.18247
      Fault Module Timestamp:    521eaf24
      Exception Code:    c0000005
      Exception Offset:    0000000000027b0b
      OS Version:    6.1.7601.2.1.0.256.48
      Locale ID:    2057
      Additional Information 1:    f116
      Additional Information 2:    f1169e5949b625e6ff320471dc2e63c2
      Additional Information 3:    ca58
      Additional Information 4:    ca58819a9254a4ddaed3ec0fe7f101b2
    I have looked up this C0000005 code and it suggests that the application is trying to address illegal blocks of memory. If that helps.
    Another classic is when I try to SAVE AS and the dialogue fails to display the folder structure in the window so I cannot select a location. Once this happens, we're heading into crash land.
    Only PHOTOSHOP does this. I have plenty of professional software and tools on my system.
    BEFORE ANYONE SUGGESTS I UPDATE MY VIDEO CARD DRIVERS, PLEASE READ:
    I have a Radeon HD7750 card, which is approved for use with PS.
    I have the very latest drivers for it (not the BETA release, but the very latest stable drivers and latest Catalyst Control Centre update). I have had problems with all versions of PS CC and CC 2014 and that's through various video card driver updates.
    I have completely uninstalled PS CC2014 and all other versions of PS and uninstalled Creative Cloud and reinstalled both from scratch to try to solve this but it hasn't helped.
    I have no third party plugins in PS
    I have done regular and recent comprehensive checks on all my hardware and updated drivers, from BIOS, to CHIPSET and everything else.
    I have no IRQ conflicts, no problems in device manager
    I have monitored my system temperatures and they are fine
    I have done 16 hours of MEMTEST+ on my 16GB of DDR3 RAM - over 4 complete passes, with no errors
    I have stress-tested my video card with FUTUREMARK and it is perfectly fine within its capabilities
    I have even installed Steam and the a PC game (which I don't normally do) and it stands up just fine, no crashes.
    I have run a Windows System Health Check and his shows green lights for everything
    I have done a file system integrity check and no errors are found
    No other software on my system crashes like this, but PS does it all the time
    I use Adobe Bridge, and I've never had it crash. I use Adobe Reader, it's fine. I use Adobe Premier Elements 12 sometimes, it's fine. Adobe Photoshop CC / 2014 is not fine.
    I don't want to moan, I really need a solution and if anyone experienced can suggest something that goes beyond doing the the above I would be very grateful for your help
    PERFORMANCE SETTINGS:
    PS SYSTEM INFO:
    Adobe Photoshop Version: 2014.2.0 20140926.r.236 2014/09/26:23:59:59  x64
    Operating System: Windows 7 64-bit
    Version: 6.1 Service Pack 1
    System architecture: Intel CPU Family:6, Model:10, Stepping:9 with MMX, SSE Integer, SSE FP, SSE2, SSE3, SSE4.1, SSE4.2, AVX, HyperThreading
    Physical processor count: 4
    Logical processor count: 8
    Processor speed: 3500 MHz
    Built-in memory: 16268 MB
    Free memory: 9930 MB
    Memory available to Photoshop: 14551 MB
    Memory used by Photoshop: 70 %
    3D Multitone Printing: Disabled.
    Windows 2x UI: Disabled.
    Highbeam: Enabled.
    Image tile size: 1024K
    Image cache levels: 4
    Font Preview: Medium
    TextComposer: Latin
    Display: 1
    Display Bounds: top=0, left=0, bottom=1080, right=1920
    Display: 2
    Display Bounds: top=0, left=1920, bottom=1024, right=3200
    OpenGL Drawing: Enabled.
    OpenGL Allow Old GPUs: Not Detected.
    OpenGL Drawing Mode: Advanced
    OpenGL Allow Normal Mode: True.
    OpenGL Allow Advanced Mode: True.
    AIFCoreInitialized=1
    AIFOGLInitialized=1
    OGLContextCreated=1
    NumGLGPUs=1
    NumCLGPUs=1
    glgpu[0].GLVersion="3.0"
    glgpu[0].GLMemoryMB=1024
    glgpu[0].GLName="AMD Radeon HD 7700 Series"
    glgpu[0].GLVendor="ATI Technologies Inc."
    glgpu[0].GLVendorID=4098
    glgpu[0].GLDriverVersion="14.301.1001.0"
    glgpu[0].GLRectTextureSize=16384
    glgpu[0].GLRenderer="AMD Radeon HD 7700 Series"
    glgpu[0].GLRendererID=26687
    glgpu[0].HasGLNPOTSupport=1
    glgpu[0].GLDriver="aticfx64.dll,aticfx64.dll,aticfx64.dll,aticfx32,aticfx32,aticfx32,atium d64.dll,atidxx64.dll,atidxx64.dll,atiumdag,atidxx32,atidxx32,atiumdva,atiumd6a.cap,atitmm6 4.dll"
    glgpu[0].GLDriverDate="20140915000000.000000-000"
    glgpu[0].CanCompileProgramGLSL=1
    glgpu[0].GLFrameBufferOK=1
    glgpu[0].glGetString[GL_SHADING_LANGUAGE_VERSION]="4.40"
    glgpu[0].glGetProgramivARB[GL_FRAGMENT_PROGRAM_ARB][GL_MAX_PROGRAM_INSTRUCTIONS_ARB]=[2147 483647]
    glgpu[0].glGetIntegerv[GL_MAX_TEXTURE_UNITS]=[8]
    glgpu[0].glGetIntegerv[GL_MAX_COMBINED_TEXTURE_IMAGE_UNITS]=[192]
    glgpu[0].glGetIntegerv[GL_MAX_VERTEX_TEXTURE_IMAGE_UNITS]=[32]
    glgpu[0].glGetIntegerv[GL_MAX_TEXTURE_IMAGE_UNITS]=[32]
    glgpu[0].glGetIntegerv[GL_MAX_DRAW_BUFFERS]=[8]
    glgpu[0].glGetIntegerv[GL_MAX_VERTEX_UNIFORM_COMPONENTS]=[16384]
    glgpu[0].glGetIntegerv[GL_MAX_FRAGMENT_UNIFORM_COMPONENTS]=[16384]
    glgpu[0].glGetIntegerv[GL_MAX_VARYING_FLOATS]=[128]
    glgpu[0].glGetIntegerv[GL_MAX_VERTEX_ATTRIBS]=[29]
    glgpu[0].extension[AIF::OGL::GL_ARB_VERTEX_PROGRAM]=1
    glgpu[0].extension[AIF::OGL::GL_ARB_FRAGMENT_PROGRAM]=1
    glgpu[0].extension[AIF::OGL::GL_ARB_VERTEX_SHADER]=1
    glgpu[0].extension[AIF::OGL::GL_ARB_FRAGMENT_SHADER]=1
    glgpu[0].extension[AIF::OGL::GL_EXT_FRAMEBUFFER_OBJECT]=1
    glgpu[0].extension[AIF::OGL::GL_ARB_TEXTURE_RECTANGLE]=1
    glgpu[0].extension[AIF::OGL::GL_ARB_TEXTURE_FLOAT]=1
    glgpu[0].extension[AIF::OGL::GL_ARB_OCCLUSION_QUERY]=1
    glgpu[0].extension[AIF::OGL::GL_ARB_VERTEX_BUFFER_OBJECT]=1
    glgpu[0].extension[AIF::OGL::GL_ARB_SHADER_TEXTURE_LOD]=1
    clgpu[0].CLPlatformVersion="1.2 AMD-APP (1573.4)"
    clgpu[0].CLDeviceVersion="1.2 AMD-APP (1573.4)"
    clgpu[0].CLMemoryMB=1024
    clgpu[0].CLName="Capeverde"
    clgpu[0].CLVendor="Advanced Micro Devices, Inc."
    clgpu[0].CLVendorID=4098
    clgpu[0].CLDriverVersion="1573.4 (VM)"
    clgpu[0].CUDASupported=0
    clgpu[0].CLBandwidth=5.25736e+010
    clgpu[0].CLCompute=379.453
    License Type: Subscription
    Serial number: {REMOVED FOR PRIVACY}
    Application folder: C:\Program Files\Adobe\Adobe Photoshop CC 2014\
    Temporary file path: C:\Users\Em\AppData\Local\Temp\
    Photoshop scratch has async I/O enabled
    Scratch volume(s):
      K:\, 221.6G, 221.2G free
      J:\, 244.1G, 233.8G free
    Required Plug-ins folder: C:\Program Files\Adobe\Adobe Photoshop CC 2014\Required\Plug-Ins\
    Primary Plug-ins folder: C:\Program Files\Adobe\Adobe Photoshop CC 2014\Plug-ins\
    Installed components:
       A3DLIBS.dll   A3DLIB Dynamic Link Library   9.2.0.112 
       ACE.dll   ACE 2014/08/12-23:42:09   79.557478   79.557478
       adbeape.dll   Adobe APE 2013/02/04-09:52:32   0.1160850   0.1160850
       AdbePM.dll   PatchMatch 2014/09/07-21:07:38   79.558079   79.558079
       AdobeLinguistic.dll   Adobe Linguisitc Library   8.0.0 
       AdobeOwl.dll   Adobe Owl   5.2.4 
       AdobePDFL.dll   PDFL 2014/08/18-15:13:12   79.512424   79.512424
       AdobePIP.dll   Adobe Product Improvement Program   7.2.1.3399 
       AdobeXMP.dll   Adobe XMP Core 2014/08/20-09:53:02   79.156797   79.156797
       AdobeXMPFiles.dll   Adobe XMP Files 2014/08/20-09:53:02   79.156797   79.156797
       AdobeXMPScript.dll   Adobe XMP Script 2014/08/20-09:53:02   79.156797   79.156797
       adobe_caps.dll   Adobe CAPS   8,0,0,13 
       AGM.dll   AGM 2014/08/12-23:42:09   79.557478   79.557478
       ahclient.dll    AdobeHelp Dynamic Link Library   1,8,0,31 
       amtlib.dll   AMTLib (64 Bit)   8.0.0.122212002 BuildVersion: 8.0; BuildDate: Wed Jul 30 2014 15:59:34)   1.000000
       ARE.dll   ARE 2014/08/12-23:42:09   79.557478   79.557478
       AXE8SharedExpat.dll   AXE8SharedExpat 2013/12/20-21:40:29   79.551013   79.551013
       AXEDOMCore.dll   AXEDOMCore 2013/12/20-21:40:29   79.551013   79.551013
       Bib.dll   BIB 2014/08/12-23:42:09   79.557478   79.557478
       BIBUtils.dll   BIBUtils 2014/08/12-23:42:09   79.557478   79.557478
       boost_date_time.dll   photoshopdva   8.0.0 
       boost_signals.dll   photoshopdva   8.0.0 
       boost_system.dll   photoshopdva   8.0.0 
       boost_threads.dll   photoshopdva   8.0.0 
       cg.dll   NVIDIA Cg Runtime   3.0.00007 
       cgGL.dll   NVIDIA Cg Runtime   3.0.00007 
       CIT.dll   Adobe CIT   2.2.6.32411   2.2.6.32411
       CITThreading.dll   Adobe CITThreading   2.2.6.32411   2.2.6.32411
       CoolType.dll   CoolType 2014/08/12-23:42:09   79.557478   79.557478
       dvaaudiodevice.dll   photoshopdva   8.0.0 
       dvacore.dll   photoshopdva   8.0.0 
       dvamarshal.dll   photoshopdva   8.0.0 
       dvamediatypes.dll   photoshopdva   8.0.0 
       dvametadata.dll   photoshopdva   8.0.0 
       dvametadataapi.dll   photoshopdva   8.0.0 
       dvametadataui.dll   photoshopdva   8.0.0 
       dvaplayer.dll   photoshopdva   8.0.0 
       dvatransport.dll   photoshopdva   8.0.0 
       dvaui.dll   photoshopdva   8.0.0 
       dvaunittesting.dll   photoshopdva   8.0.0 
       dynamiclink.dll   photoshopdva   8.0.0 
       ExtendScript.dll   ExtendScript 2014/01/21-23:58:55   79.551519   79.551519
       icucnv40.dll   International Components for Unicode 2013/02/25-15:59:15    Build gtlib_4.0.19090 
       icudt40.dll   International Components for Unicode 2013/02/25-15:59:15    Build gtlib_4.0.19090 
       igestep30.dll   IGES Reader   9.3.0.113 
       imslib.dll   IMSLib DLL   7.0.0.154 
       JP2KLib.dll   JP2KLib 2014/06/28-00:28:27   79.254012   79.254012
       libifcoremd.dll   Intel(r) Visual Fortran Compiler   10.0 (Update A) 
       libiomp5md.dll   Intel(R) OpenMP* Runtime Library   5.0 
       libmmd.dll   Intel(r) C Compiler, Intel(r) C++ Compiler, Intel(r) Fortran Compiler   12.0 
       LogSession.dll   LogSession   7.2.1.3399 
       mediacoreif.dll   photoshopdva   8.0.0 
       MPS.dll   MPS 2014/08/18-23:43:19   79.557676   79.557676
       pdfsettings.dll   Adobe PDFSettings   1.04 
       Photoshop.dll   Adobe Photoshop CC 2014   15.2 
       Plugin.dll   Adobe Photoshop CC 2014   15.2 
       PlugPlugExternalObject.dll   Adobe(R) CEP PlugPlugExternalObject Standard Dll (64 bit)   5.0.0 
       PlugPlugOwl.dll   Adobe(R) CSXS PlugPlugOwl Standard Dll (64 bit)   5.2.0.46 
       PSArt.dll   Adobe Photoshop CC 2014   15.2 
       PSViews.dll   Adobe Photoshop CC 2014   15.2 
       SCCore.dll   ScCore 2014/01/21-23:58:55   79.551519   79.551519
       ScriptUIFlex.dll   ScriptUIFlex 2014/01/20-22:42:05   79.550992   79.550992
       svml_dispmd.dll   Intel(r) C Compiler, Intel(r) C++ Compiler, Intel(r) Fortran Compiler   12.0 
       tbb.dll   Intel(R) Threading Building Blocks for Windows   4, 2, 2013, 1114 
       tbbmalloc.dll   Intel(R) Threading Building Blocks for Windows   4, 2, 2013, 1114 
       TfFontMgr.dll   FontMgr   9.3.0.113 
       TfKernel.dll   Kernel   9.3.0.113 
       TFKGEOM.dll   Kernel Geom   9.3.0.113 
       TFUGEOM.dll   Adobe, UGeom©   9.3.0.113 
       updaternotifications.dll   Adobe Updater Notifications Library   8.0.0.14 (BuildVersion: 1.0; BuildDate: BUILDDATETIME)   8.0.0.14
       VulcanControl.dll   Vulcan Application Control Library   5.0.0.82 
       VulcanMessage5.dll   Vulcan Message Library   5.0.0.82 
       WRServices.dll   WRServices Fri Mar 07 2014 15:33:10   Build 0.20204   0.20204
       wu3d.dll   U3D Writer   9.3.0.113 
    Required plug-ins:
       3D Studio 15.2 (2014.2.0 x001)
       Accented Edges 15.2
       Adaptive Wide Angle 15.2
       Angled Strokes 15.2
       Average 15.2 (2014.2.0 x001)
       Bas Relief 15.2
       BMP 15.2
       Camera Raw 8.6
       Camera Raw Filter 8.6
       Chalk & Charcoal 15.2
       Charcoal 15.2
       Chrome 15.2
       Cineon 15.2 (2014.2.0 x001)
       Clouds 15.2 (2014.2.0 x001)
       Collada 15.2 (2014.2.0 x001)
       Color Halftone 15.2
       Colored Pencil 15.2
       CompuServe GIF 15.2
       Conté Crayon 15.2
       Craquelure 15.2
       Crop and Straighten Photos 15.2 (2014.2.0 x001)
       Crop and Straighten Photos Filter 15.2
       Crosshatch 15.2
       Crystallize 15.2
       Cutout 15.2
       Dark Strokes 15.2
       De-Interlace 15.2
       Dicom 15.2
       Difference Clouds 15.2 (2014.2.0 x001)
       Diffuse Glow 15.2
       Displace 15.2
       Dry Brush 15.2
       Eazel Acquire 15.2 (2014.2.0 x001)
       Embed Watermark 4.0
       Entropy 15.2 (2014.2.0 x001)
       Export Color Lookup Tables NO VERSION
       Extrude 15.2
       FastCore Routines 15.2 (2014.2.0 x001)
       Fibers 15.2
       Film Grain 15.2
       Filter Gallery 15.2
       Flash 3D 15.2 (2014.2.0 x001)
       Fresco 15.2
       Glass 15.2
       Glowing Edges 15.2
       Google Earth 4 15.2 (2014.2.0 x001)
       Grain 15.2
       Graphic Pen 15.2
       Halftone Pattern 15.2
       HDRMergeUI 15.2
       HSB/HSL 15.2
       IFF Format 15.2
       IGES 15.2 (2014.2.0 x001)
       Ink Outlines 15.2
       JPEG 2000 15.2
       Kurtosis 15.2 (2014.2.0 x001)
       Lens Blur 15.2
       Lens Correction 15.2
       Lens Flare 15.2
       Liquify 15.2
       Matlab Operation 15.2 (2014.2.0 x001)
       Maximum 15.2 (2014.2.0 x001)
       Mean 15.2 (2014.2.0 x001)
       Measurement Core 15.2 (2014.2.0 x001)
       Median 15.2 (2014.2.0 x001)
       Mezzotint 15.2
       Minimum 15.2 (2014.2.0 x001)
       MMXCore Routines 15.2 (2014.2.0 x001)
       Mosaic Tiles 15.2
       Multiprocessor Support 15.2 (2014.2.0 x001)
       Neon Glow 15.2
       Note Paper 15.2
       NTSC Colors 15.2 (2014.2.0 x001)
       Ocean Ripple 15.2
       OpenEXR 15.2
       Paint Daubs 15.2
       Palette Knife 15.2
       Patchwork 15.2
       Paths to Illustrator 15.2
       PCX 15.2 (2014.2.0 x001)
       Photocopy 15.2
       Photoshop 3D Engine 15.2 (2014.2.0 x001)
       Photoshop Touch 14.0
       Picture Package Filter 15.2 (2014.2.0 x001)
       Pinch 15.2
       Pixar 15.2 (2014.2.0 x001)
       Plaster 15.2
       Plastic Wrap 15.2
       PLY 15.2 (2014.2.0 x001)
       PNG 15.2
       Pointillize 15.2
       Polar Coordinates 15.2
       Portable Bit Map 15.2 (2014.2.0 x001)
       Poster Edges 15.2
       PRC 15.2 (2014.2.0 x001)
       Radial Blur 15.2
       Radiance 15.2 (2014.2.0 x001)
       Range 15.2 (2014.2.0 x001)
       Read Watermark 4.0
       Render Color Lookup Grid NO VERSION
       Reticulation 15.2
       Ripple 15.2
       Rough Pastels 15.2
       Save for Web 15.2
       ScriptingSupport 15.2
       Shake Reduction 15.2
       Shear 15.2
       Skewness 15.2 (2014.2.0 x001)
       Smart Blur 15.2
       Smudge Stick 15.2
       Solarize 15.2 (2014.2.0 x001)
       Spatter 15.2
       Spherize 15.2
       Sponge 15.2
       Sprayed Strokes 15.2
       Stained Glass 15.2
       Stamp 15.2
       Standard Deviation 15.2 (2014.2.0 x001)
       STL 15.2 (2014.2.0 x001)
       Sumi-e 15.2
       Summation 15.2 (2014.2.0 x001)
       Targa 15.2
       Texturizer 15.2
       Tiles 15.2
       Torn Edges 15.2
       Twirl 15.2
       U3D 15.2 (2014.2.0 x001)
       Underpainting 15.2
       Vanishing Point 15.2
       Variance 15.2 (2014.2.0 x001)
       Virtual Reality Modeling Language | VRML 15.2 (2014.2.0 x001)
       Water Paper 15.2
       Watercolor 15.2
       Wave 15.2
       Wavefront|OBJ 15.2 (2014.2.0 x001)
       WIA Support 15.2 (2014.2.0 x001)
       Wind 15.2
       Wireless Bitmap 15.2 (2014.2.0 x001)
       ZigZag 15.2
    Optional and third party plug-ins: NONE
    Plug-ins that failed to load: NONE
    Flash:
       Libraries
       Adobe Color Themes
    Installed TWAIN devices: NONE
    Can anyone help me resolve this issue, with suggestions beyond those I've already listed above?
    I'm getting pretty stuck...
    Thanks

    Hi Chris
    Like I said in the OP I had the very latest AMD drivers installed before submitting that crash report.
    Since our conversations, I have completely removed my Radeon HD7750 GPU, uninstalled the drivers for it and the Catalyst Control Centre, and have resorted to using to my motherboard's integrated Intel HD graphics. I have the very latest drivers for the Intel HD graphics installed. Still, today I have had another crash event in Photoshop. So this cannot be the fault of the AMD card or drivers, because they are no longer present on the system.
    CRASH:
    Faulting application name: Photoshop.exe, version: 15.2.0.236, time stamp: 0x542531ba
    Faulting module name: ntdll.dll, version: 6.1.7601.18247, time stamp: 0x521eaf24
    Exception code: 0xc0000005
    Fault offset: 0x0000000000027b0b
    Faulting process id: 0x1fd8
    Faulting application start time: 0x01cfe7c41d6b75d0
    Faulting application path: C:\Program Files\Adobe\Adobe Photoshop CC 2014\Photoshop.exe
    Faulting module path: C:\Windows\SYSTEM32\ntdll.dll
    Report Id: a9fd0b69-53c1-11e4-8d80-bc5ff43517ae
    Fault bucket , type 0
    Event Name: APPCRASH
    Response: Not available
    Cab Id: 0
    Problem signature:
    P1: Photoshop.exe
    P2: 15.2.0.236
    P3: 542531ba
    P4: ntdll.dll
    P5: 6.1.7601.18247
    P6: 521eaf24
    P7: c0000005
    P8: 0000000000027b0b
    P9:
    P10:
    Additional files: - I have a report file I am trying to post but this forum tells me I am spamming when I try to submit. I will try to post it separately...

  • Help with crashes

    So... this will be a bit long...
    I am getting some serious problems with my machine, and I don't think I can solve this my self. I be not very tech-savvy.
    Recently I upgraded my cpu video card and ram in a period of 1-2 weeks. Everything was fine at one point, but then stuff went bad.
    I am dual booting arch with win. My win started crashing during loading sreen, but only at first boot of the day. Then no problem. I decided to ignore.
    At that time I was using only win for like a month. Then after the ram upgrade my whole pc started crashing at random times.
    I decided to switch the new ram with an other one. Then the crashes stoped, but still I had that loading screen crash at first boot.
    Never the less everything else was fine.
    Then I went to arch to use it again. First my firefox started crashing at random times (the same stuff was happening in win before the second ram change,
    after that win's firefox was fine but not the arch one). Then my whole sistem started crashing at random times first only when I go on youtube,
    but now when I watch videos offline too and use firefox for other things. I dont know what I am supposed to do. I was reading some of the wiki and
    installed mcelog to see if it can catch something.
    Here is log from last crash:
    /var/log/mcelog
    mcelog: failed to prefill DIMM database from DMI data
    Hardware event. This is not a software error.
    MCE 0
    CPU 0 BANK 0
    TIME 1405256587 Sun Jul 13 16:03:07 2014
    MCG status:
    MCi status:
    Uncorrected error
    Error enabled
    Processor context corrupt
    MCA: BUS Level-0 Local-CPU-originated-request Generic Memory-access Request-did-not-timeout Error
    BQ_DCU_READ_TYPE BQ_ERR_HARD_TYPE BQ_ERR_HARD_TYPE
    timeout BINIT (ROB timeout). No micro-instruction retired for some time
    STATUS b200004000000800 MCGSTATUS 0
    MCGCAP 806 APICID 0 SOCKETID 0
    CPUID Vendor Intel Family 6 Model 23
    Hardware event. This is not a software error.
    MCE 1
    CPU 0 BANK 5
    TIME 1405256587 Sun Jul 13 16:03:07 2014
    MCG status:
    MCi status:
    Uncorrected error
    Error enabled
    Processor context corrupt
    MCA: BUS Level-3 Generic Generic Other-transaction Request-did-not-timeout Error
    BQ_DCU_READ_TYPE BQ_ERR_AERR2_TYPE BQ_ERR_AERR2_TYPE
    received parity error on response transaction
    MCE driven
    STATUS b200001014000e0f MCGSTATUS 0
    MCGCAP 806 APICID 0 SOCKETID 0
    CPUID Vendor Intel Family 6 Model 23
    Hardware event. This is not a software error.
    MCE 2
    CPU 1 BANK 5
    TIME 1405256587 Sun Jul 13 16:03:07 2014
    MCG status:
    MCi status:
    Uncorrected error
    Error enabled
    Processor context corrupt
    MCA: BUS Level-3 Generic Generic Other-transaction Request-did-not-timeout Error
    BQ_DCU_READ_TYPE BQ_ERR_HARD_TYPE BQ_ERR_HARD_TYPE
    received parity error on response transaction
    MCE is observed
    STATUS b200001020000e0f MCGSTATUS 0
    MCGCAP 806 APICID 1 SOCKETID 0
    CPUID Vendor Intel Family 6 Model 23
    here is journalctl -b -1
    -- Logs begin at Wed 2015-07-02 16:37:48 EEST, end at Sun 2014-07-13 16:51:07 EEST. --
    Jul 13 12:37:34 ma3x systemd-journal[133]: Runtime journal is using 8.0M (max allowed 197.8M, trying to leave 296.6M free of 1.9G available → current limit 197.8M).
    Jul 13 12:37:34 ma3x systemd-journal[133]: Runtime journal is using 8.0M (max allowed 197.8M, trying to leave 296.6M free of 1.9G available → current limit 197.8M).
    Jul 13 12:37:34 ma3x kernel: Initializing cgroup subsys cpuset
    Jul 13 12:37:34 ma3x kernel: Initializing cgroup subsys cpu
    Jul 13 12:37:34 ma3x kernel: Initializing cgroup subsys cpuacct
    Jul 13 12:37:34 ma3x kernel: Linux version 3.15.5-1-ARCH (nobody@var-lib-archbuild-testing-x86_64-tobias) (gcc version 4.9.0 20140604 (prerelease) (GCC) ) #1 SMP PREEMPT Thu Jul 10 07:08:50 CEST 2014
    Jul 13 12:37:34 ma3x kernel: Command line: BOOT_IMAGE=/boot/vmlinuz-linux root=UUID=2f1b0e26-dfb8-4c78-8320-1675a6d5f935 rw quiet
    Jul 13 12:37:34 ma3x kernel: e820: BIOS-provided physical RAM map:
    Jul 13 12:37:34 ma3x kernel: BIOS-e820: [mem 0x0000000000000000-0x000000000009f3ff] usable
    Jul 13 12:37:34 ma3x kernel: BIOS-e820: [mem 0x000000000009f400-0x000000000009ffff] reserved
    Jul 13 12:37:34 ma3x kernel: BIOS-e820: [mem 0x00000000000f0000-0x00000000000fffff] reserved
    Jul 13 12:37:34 ma3x kernel: BIOS-e820: [mem 0x0000000000100000-0x00000000cfe8ffff] usable
    Jul 13 12:37:34 ma3x kernel: BIOS-e820: [mem 0x00000000cfe90000-0x00000000cfedffff] reserved
    Jul 13 12:37:34 ma3x kernel: BIOS-e820: [mem 0x00000000cfee0000-0x00000000cfee2fff] ACPI NVS
    Jul 13 12:37:34 ma3x kernel: BIOS-e820: [mem 0x00000000cfee3000-0x00000000cfeeffff] ACPI data
    Jul 13 12:37:34 ma3x kernel: BIOS-e820: [mem 0x00000000cfef0000-0x00000000cfefffff] reserved
    Jul 13 12:37:34 ma3x kernel: BIOS-e820: [mem 0x00000000e0000000-0x00000000efffffff] reserved
    Jul 13 12:37:34 ma3x kernel: BIOS-e820: [mem 0x00000000fec00000-0x00000000ffffffff] reserved
    Jul 13 12:37:34 ma3x kernel: BIOS-e820: [mem 0x0000000100000000-0x000000012fffffff] usable
    Jul 13 12:37:34 ma3x kernel: NX (Execute Disable) protection: active
    Jul 13 12:37:34 ma3x kernel: SMBIOS 2.5 present.
    Jul 13 12:37:34 ma3x kernel: DMI: / , BIOS 6.00 PG 12/04/2007
    Jul 13 12:37:34 ma3x kernel: e820: update [mem 0x00000000-0x00000fff] usable ==> reserved
    Jul 13 12:37:34 ma3x kernel: e820: remove [mem 0x000a0000-0x000fffff] usable
    Jul 13 12:37:34 ma3x kernel: No AGP bridge found
    Jul 13 12:37:34 ma3x kernel: e820: last_pfn = 0x130000 max_arch_pfn = 0x400000000
    Jul 13 12:37:34 ma3x kernel: MTRR default type: uncachable
    Jul 13 12:37:34 ma3x kernel: MTRR fixed ranges enabled:
    Jul 13 12:37:34 ma3x kernel: 00000-9FFFF write-back
    Jul 13 12:37:34 ma3x kernel: A0000-BFFFF uncachable
    Jul 13 12:37:34 ma3x kernel: C0000-CEFFF write-protect
    Jul 13 12:37:34 ma3x kernel: CF000-EFFFF uncachable
    Jul 13 12:37:34 ma3x kernel: F0000-FFFFF write-through
    Jul 13 12:37:34 ma3x kernel: MTRR variable ranges enabled:
    Jul 13 12:37:34 ma3x kernel: 0 base 100000000 mask FE0000000 write-back
    Jul 13 12:37:34 ma3x kernel: 1 base 120000000 mask FF0000000 write-back
    Jul 13 12:37:34 ma3x kernel: 2 base 000000000 mask F80000000 write-back
    Jul 13 12:37:34 ma3x kernel: 3 base 080000000 mask FC0000000 write-back
    Jul 13 12:37:34 ma3x kernel: 4 base 0C0000000 mask FF0000000 write-back
    Jul 13 12:37:34 ma3x kernel: 5 base 0CFF00000 mask FFFF00000 uncachable
    Jul 13 12:37:34 ma3x kernel: 6 disabled
    Jul 13 12:37:34 ma3x kernel: 7 disabled
    Jul 13 12:37:34 ma3x kernel: x86 PAT enabled: cpu 0, old 0x7040600070406, new 0x7010600070106
    Jul 13 12:37:34 ma3x kernel: e820: update [mem 0xcff00000-0xffffffff] usable ==> reserved
    Jul 13 12:37:34 ma3x kernel: e820: last_pfn = 0xcfe90 max_arch_pfn = 0x400000000
    Jul 13 12:37:34 ma3x kernel: found SMP MP-table at [mem 0x000f3ab0-0x000f3abf] mapped at [ffff8800000f3ab0]
    Jul 13 12:37:34 ma3x kernel: Scanning 1 areas for low memory corruption
    Jul 13 12:37:34 ma3x kernel: Base memory trampoline at [ffff880000099000] 99000 size 24576
    Jul 13 12:37:34 ma3x kernel: init_memory_mapping: [mem 0x00000000-0x000fffff]
    Jul 13 12:37:34 ma3x kernel: [mem 0x00000000-0x000fffff] page 4k
    Jul 13 12:37:34 ma3x kernel: BRK [0x01b3e000, 0x01b3efff] PGTABLE
    Jul 13 12:37:34 ma3x kernel: BRK [0x01b3f000, 0x01b3ffff] PGTABLE
    Jul 13 12:37:34 ma3x kernel: BRK [0x01b40000, 0x01b40fff] PGTABLE
    Jul 13 12:37:34 ma3x kernel: init_memory_mapping: [mem 0x12fe00000-0x12fffffff]
    Jul 13 12:37:34 ma3x kernel: [mem 0x12fe00000-0x12fffffff] page 2M
    Jul 13 12:37:34 ma3x kernel: BRK [0x01b41000, 0x01b41fff] PGTABLE
    Jul 13 12:37:34 ma3x kernel: init_memory_mapping: [mem 0x12c000000-0x12fdfffff]
    Jul 13 12:37:34 ma3x kernel: [mem 0x12c000000-0x12fdfffff] page 2M
    Jul 13 12:37:34 ma3x kernel: init_memory_mapping: [mem 0x100000000-0x12bffffff]
    Jul 13 12:37:34 ma3x kernel: [mem 0x100000000-0x12bffffff] page 2M
    Jul 13 12:37:34 ma3x kernel: init_memory_mapping: [mem 0x00100000-0xcfe8ffff]
    Jul 13 12:37:34 ma3x kernel: [mem 0x00100000-0x001fffff] page 4k
    Jul 13 12:37:34 ma3x kernel: [mem 0x00200000-0xcfdfffff] page 2M
    Jul 13 12:37:34 ma3x kernel: [mem 0xcfe00000-0xcfe8ffff] page 4k
    Jul 13 12:37:34 ma3x kernel: RAMDISK: [mem 0x379be000-0x37cd6fff]
    Jul 13 12:37:34 ma3x kernel: ACPI: RSDP 0x00000000000F7D00 000024 (v02 IntelR)
    Jul 13 12:37:34 ma3x kernel: ACPI: XSDT 0x00000000CFEE3080 000044 (v01 IntelR AWRDACPI 42302E31 AWRD 00000000)
    Jul 13 12:37:34 ma3x kernel: ACPI: FACP 0x00000000CFEE80C0 0000F4 (v03 IntelR AWRDACPI 42302E31 AWRD 00000000)
    Jul 13 12:37:34 ma3x kernel: ACPI BIOS Warning (bug): 32/64X length mismatch in FADT/Pm1aEventBlock: 32/8 (20140214/tbfadt-603)
    Jul 13 12:37:34 ma3x kernel: ACPI BIOS Warning (bug): 32/64X length mismatch in FADT/Pm1aControlBlock: 16/8 (20140214/tbfadt-603)
    Jul 13 12:37:34 ma3x kernel: ACPI BIOS Warning (bug): 32/64X length mismatch in FADT/PmTimerBlock: 32/8 (20140214/tbfadt-603)
    Jul 13 12:37:34 ma3x kernel: ACPI BIOS Warning (bug): 32/64X length mismatch in FADT/Gpe0Block: 128/8 (20140214/tbfadt-603)
    Jul 13 12:37:34 ma3x kernel: ACPI BIOS Warning (bug): Invalid length for FADT/Pm1aEventBlock: 8, using default 32 (20140214/tbfadt-684)
    Jul 13 12:37:34 ma3x kernel: ACPI BIOS Warning (bug): Invalid length for FADT/Pm1aControlBlock: 8, using default 16 (20140214/tbfadt-684)
    Jul 13 12:37:34 ma3x kernel: ACPI BIOS Warning (bug): Invalid length for FADT/PmTimerBlock: 8, using default 32 (20140214/tbfadt-684)
    Jul 13 12:37:34 ma3x kernel: ACPI: DSDT 0x00000000CFEE31C0 004EFC (v01 INTELR AWRDACPI 00001000 MSFT 03000000)
    Jul 13 12:37:34 ma3x kernel: ACPI: FACS 0x00000000CFEE0000 000040
    Jul 13 12:37:34 ma3x kernel: ACPI: MCFG 0x00000000CFEE8280 00003C (v01 IntelR AWRDACPI 42302E31 AWRD 00000000)
    Jul 13 12:37:34 ma3x kernel: ACPI: APIC 0x00000000CFEE81C0 000084 (v01 IntelR AWRDACPI 42302E31 AWRD 00000000)
    Jul 13 12:37:34 ma3x kernel: ACPI: SSDT 0x00000000CFEE8920 000817 (v01 PmRef CpuPm 00003000 INTL 20060113)
    Jul 13 12:37:34 ma3x kernel: ACPI: Local APIC address 0xfee00000
    Jul 13 12:37:34 ma3x kernel: No NUMA configuration found
    Jul 13 12:37:34 ma3x kernel: Faking a node at [mem 0x0000000000000000-0x000000012fffffff]
    Jul 13 12:37:34 ma3x kernel: Initmem setup node 0 [mem 0x00000000-0x12fffffff]
    Jul 13 12:37:34 ma3x kernel: NODE_DATA [mem 0x12fff7000-0x12fffbfff]
    Jul 13 12:37:34 ma3x kernel: [ffffea0000000000-ffffea0004bfffff] PMD -> [ffff88012b600000-ffff88012f5fffff] on node 0
    Jul 13 12:37:34 ma3x kernel: Zone ranges:
    Jul 13 12:37:34 ma3x kernel: DMA [mem 0x00001000-0x00ffffff]
    Jul 13 12:37:34 ma3x kernel: DMA32 [mem 0x01000000-0xffffffff]
    Jul 13 12:37:34 ma3x kernel: Normal [mem 0x100000000-0x12fffffff]
    Jul 13 12:37:34 ma3x kernel: Movable zone start for each node
    Jul 13 12:37:34 ma3x kernel: Early memory node ranges
    Jul 13 12:37:34 ma3x kernel: node 0: [mem 0x00001000-0x0009efff]
    Jul 13 12:37:34 ma3x kernel: node 0: [mem 0x00100000-0xcfe8ffff]
    Jul 13 12:37:34 ma3x kernel: node 0: [mem 0x100000000-0x12fffffff]
    Jul 13 12:37:34 ma3x kernel: On node 0 totalpages: 1048110
    Jul 13 12:37:34 ma3x kernel: DMA zone: 64 pages used for memmap
    Jul 13 12:37:34 ma3x kernel: DMA zone: 21 pages reserved
    Jul 13 12:37:34 ma3x kernel: DMA zone: 3998 pages, LIFO batch:0
    Jul 13 12:37:34 ma3x kernel: DMA32 zone: 13243 pages used for memmap
    Jul 13 12:37:34 ma3x kernel: DMA32 zone: 847504 pages, LIFO batch:31
    Jul 13 12:37:34 ma3x kernel: Normal zone: 3072 pages used for memmap
    Jul 13 12:37:34 ma3x kernel: Normal zone: 196608 pages, LIFO batch:31
    Jul 13 12:37:34 ma3x kernel: ACPI: PM-Timer IO Port: 0x408
    Jul 13 12:37:34 ma3x kernel: ACPI: Local APIC address 0xfee00000
    Jul 13 12:37:34 ma3x kernel: ACPI: LAPIC (acpi_id[0x00] lapic_id[0x00] enabled)
    Jul 13 12:37:34 ma3x kernel: ACPI: LAPIC (acpi_id[0x01] lapic_id[0x01] enabled)
    Jul 13 12:37:34 ma3x kernel: ACPI: LAPIC (acpi_id[0x02] lapic_id[0x02] disabled)
    Jul 13 12:37:34 ma3x kernel: ACPI: LAPIC (acpi_id[0x03] lapic_id[0x03] disabled)
    Jul 13 12:37:34 ma3x kernel: ACPI: LAPIC_NMI (acpi_id[0x00] high edge lint[0x1])
    Jul 13 12:37:34 ma3x kernel: ACPI: LAPIC_NMI (acpi_id[0x01] high edge lint[0x1])
    Jul 13 12:37:34 ma3x kernel: ACPI: LAPIC_NMI (acpi_id[0x02] high edge lint[0x1])
    Jul 13 12:37:34 ma3x kernel: ACPI: LAPIC_NMI (acpi_id[0x03] high edge lint[0x1])
    Jul 13 12:37:34 ma3x kernel: ACPI: IOAPIC (id[0x04] address[0xfec00000] gsi_base[0])
    Jul 13 12:37:34 ma3x kernel: IOAPIC[0]: apic_id 4, version 32, address 0xfec00000, GSI 0-23
    Jul 13 12:37:34 ma3x kernel: ACPI: INT_SRC_OVR (bus 0 bus_irq 0 global_irq 2 dfl dfl)
    Jul 13 12:37:34 ma3x kernel: ACPI: INT_SRC_OVR (bus 0 bus_irq 9 global_irq 9 high level)
    Jul 13 12:37:34 ma3x kernel: ACPI: IRQ0 used by override.
    Jul 13 12:37:34 ma3x kernel: ACPI: IRQ2 used by override.
    Jul 13 12:37:34 ma3x kernel: ACPI: IRQ9 used by override.
    Jul 13 12:37:34 ma3x kernel: Using ACPI (MADT) for SMP configuration information
    Jul 13 12:37:34 ma3x kernel: smpboot: Allowing 4 CPUs, 2 hotplug CPUs
    Jul 13 12:37:34 ma3x kernel: nr_irqs_gsi: 40
    Jul 13 12:37:34 ma3x kernel: PM: Registered nosave memory: [mem 0x0009f000-0x0009ffff]
    Jul 13 12:37:34 ma3x kernel: PM: Registered nosave memory: [mem 0x000a0000-0x000effff]
    Jul 13 12:37:34 ma3x kernel: PM: Registered nosave memory: [mem 0x000f0000-0x000fffff]
    Jul 13 12:37:34 ma3x kernel: PM: Registered nosave memory: [mem 0xcfe90000-0xcfedffff]
    Jul 13 12:37:34 ma3x kernel: PM: Registered nosave memory: [mem 0xcfee0000-0xcfee2fff]
    Jul 13 12:37:34 ma3x kernel: PM: Registered nosave memory: [mem 0xcfee3000-0xcfeeffff]
    Jul 13 12:37:34 ma3x kernel: PM: Registered nosave memory: [mem 0xcfef0000-0xcfefffff]
    Jul 13 12:37:34 ma3x kernel: PM: Registered nosave memory: [mem 0xcff00000-0xdfffffff]
    Jul 13 12:37:34 ma3x kernel: PM: Registered nosave memory: [mem 0xe0000000-0xefffffff]
    Jul 13 12:37:34 ma3x kernel: PM: Registered nosave memory: [mem 0xf0000000-0xfebfffff]
    Jul 13 12:37:34 ma3x kernel: PM: Registered nosave memory: [mem 0xfec00000-0xffffffff]
    Jul 13 12:37:34 ma3x kernel: e820: [mem 0xcff00000-0xdfffffff] available for PCI devices
    Jul 13 12:37:34 ma3x kernel: Booting paravirtualized kernel on bare hardware
    Jul 13 12:37:34 ma3x kernel: setup_percpu: NR_CPUS:128 nr_cpumask_bits:128 nr_cpu_ids:4 nr_node_ids:1
    Jul 13 12:37:34 ma3x kernel: PERCPU: Embedded 29 pages/cpu @ffff88012fc00000 s87168 r8192 d23424 u524288
    Jul 13 12:37:34 ma3x kernel: pcpu-alloc: s87168 r8192 d23424 u524288 alloc=1*2097152
    Jul 13 12:37:34 ma3x kernel: pcpu-alloc: [0] 0 1 2 3
    Jul 13 12:37:34 ma3x kernel: Built 1 zonelists in Node order, mobility grouping on. Total pages: 1031710
    Jul 13 12:37:34 ma3x kernel: Policy zone: Normal
    Jul 13 12:37:34 ma3x kernel: Kernel command line: BOOT_IMAGE=/boot/vmlinuz-linux root=UUID=2f1b0e26-dfb8-4c78-8320-1675a6d5f935 rw quiet
    Jul 13 12:37:34 ma3x kernel: PID hash table entries: 4096 (order: 3, 32768 bytes)
    Jul 13 12:37:34 ma3x kernel: xsave: enabled xstate_bv 0x3, cntxt size 0x240
    Jul 13 12:37:34 ma3x kernel: Checking aperture...
    Jul 13 12:37:34 ma3x kernel: No AGP bridge found
    Jul 13 12:37:34 ma3x kernel: Calgary: detecting Calgary via BIOS EBDA area
    Jul 13 12:37:34 ma3x kernel: Calgary: Unable to locate Rio Grande table in EBDA - bailing!
    Jul 13 12:37:34 ma3x kernel: Memory: 4045312K/4192440K available (5224K kernel code, 886K rwdata, 1644K rodata, 1116K init, 1284K bss, 147128K reserved)
    Jul 13 12:37:34 ma3x kernel: SLUB: HWalign=64, Order=0-3, MinObjects=0, CPUs=4, Nodes=1
    Jul 13 12:37:34 ma3x kernel: Preemptible hierarchical RCU implementation.
    Jul 13 12:37:34 ma3x kernel: RCU dyntick-idle grace-period acceleration is enabled.
    Jul 13 12:37:34 ma3x kernel: Dump stacks of tasks blocking RCU-preempt GP.
    Jul 13 12:37:34 ma3x kernel: RCU restricting CPUs from NR_CPUS=128 to nr_cpu_ids=4.
    Jul 13 12:37:34 ma3x kernel: RCU: Adjusting geometry for rcu_fanout_leaf=16, nr_cpu_ids=4
    Jul 13 12:37:34 ma3x kernel: NR_IRQS:8448 nr_irqs:712 16
    Jul 13 12:37:34 ma3x kernel: Console: colour dummy device 80x25
    Jul 13 12:37:34 ma3x kernel: console [tty0] enabled
    Jul 13 12:37:34 ma3x kernel: allocated 16777216 bytes of page_cgroup
    Jul 13 12:37:34 ma3x kernel: please try 'cgroup_disable=memory' option if you don't want memory cgroups
    Jul 13 12:37:34 ma3x kernel: tsc: Fast TSC calibration using PIT
    Jul 13 12:37:34 ma3x kernel: tsc: Detected 3012.601 MHz processor
    Jul 13 12:37:34 ma3x kernel: Calibrating delay loop (skipped), value calculated using timer frequency.. 6027.25 BogoMIPS (lpj=10042003)
    Jul 13 12:37:34 ma3x kernel: pid_max: default: 32768 minimum: 301
    Jul 13 12:37:34 ma3x kernel: ACPI: Core revision 20140214
    Jul 13 12:37:34 ma3x kernel: ACPI: All ACPI Tables successfully acquired
    Jul 13 12:37:34 ma3x kernel: Security Framework initialized
    Jul 13 12:37:34 ma3x kernel: Yama: becoming mindful.
    Jul 13 12:37:34 ma3x kernel: Dentry cache hash table entries: 524288 (order: 10, 4194304 bytes)
    Jul 13 12:37:34 ma3x kernel: Inode-cache hash table entries: 262144 (order: 9, 2097152 bytes)
    Jul 13 12:37:34 ma3x kernel: Mount-cache hash table entries: 8192 (order: 4, 65536 bytes)
    Jul 13 12:37:34 ma3x kernel: Mountpoint-cache hash table entries: 8192 (order: 4, 65536 bytes)
    Jul 13 12:37:34 ma3x kernel: Initializing cgroup subsys memory
    Jul 13 12:37:34 ma3x kernel: Initializing cgroup subsys devices
    Jul 13 12:37:34 ma3x kernel: Initializing cgroup subsys freezer
    Jul 13 12:37:34 ma3x kernel: Initializing cgroup subsys net_cls
    Jul 13 12:37:34 ma3x kernel: Initializing cgroup subsys blkio
    Jul 13 12:37:34 ma3x kernel: CPU: Physical Processor ID: 0
    Jul 13 12:37:34 ma3x kernel: CPU: Processor Core ID: 0
    Jul 13 12:37:34 ma3x kernel: mce: CPU supports 6 MCE banks
    Jul 13 12:37:34 ma3x kernel: CPU0: Thermal monitoring enabled (TM2)
    Jul 13 12:37:34 ma3x kernel: Last level iTLB entries: 4KB 128, 2MB 4, 4MB 4
    Last level dTLB entries: 4KB 256, 2MB 0, 4MB 32, 1GB 0
    tlb_flushall_shift: -1
    Jul 13 12:37:34 ma3x kernel: Freeing SMP alternatives memory: 20K (ffffffff819f6000 - ffffffff819fb000)
    Jul 13 12:37:34 ma3x kernel: ftrace: allocating 20229 entries in 80 pages
    Jul 13 12:37:34 ma3x kernel: ..TIMER: vector=0x30 apic1=0 pin1=2 apic2=-1 pin2=-1
    Jul 13 12:37:34 ma3x kernel: smpboot: CPU0: Intel(R) Pentium(R) CPU E5700 @ 3.00GHz (fam: 06, model: 17, stepping: 0a)
    Jul 13 12:37:34 ma3x kernel: Performance Events: PEBS fmt0+, 4-deep LBR, Core2 events, Intel PMU driver.
    Jul 13 12:37:34 ma3x kernel: ... version: 2
    Jul 13 12:37:34 ma3x kernel: ... bit width: 40
    Jul 13 12:37:34 ma3x kernel: ... generic registers: 2
    Jul 13 12:37:34 ma3x kernel: ... value mask: 000000ffffffffff
    Jul 13 12:37:34 ma3x kernel: ... max period: 000000007fffffff
    Jul 13 12:37:34 ma3x kernel: ... fixed-purpose events: 3
    Jul 13 12:37:34 ma3x kernel: ... event mask: 0000000700000003
    Jul 13 12:37:34 ma3x kernel: NMI watchdog: enabled on all CPUs, permanently consumes one hw-PMU counter.
    Jul 13 12:37:34 ma3x kernel: x86: Booting SMP configuration:
    Jul 13 12:37:34 ma3x kernel: .... node #0, CPUs: #1
    Jul 13 12:37:34 ma3x kernel: x86: Booted up 1 node, 2 CPUs
    Jul 13 12:37:34 ma3x kernel: smpboot: Total of 2 processors activated (12055.50 BogoMIPS)
    Jul 13 12:37:34 ma3x kernel: devtmpfs: initialized
    Jul 13 12:37:34 ma3x kernel: PM: Registering ACPI NVS region [mem 0xcfee0000-0xcfee2fff] (12288 bytes)
    Jul 13 12:37:34 ma3x kernel: pinctrl core: initialized pinctrl subsystem
    Jul 13 12:37:34 ma3x kernel: RTC time: 9:37:31, date: 07/13/14
    Jul 13 12:37:34 ma3x kernel: NET: Registered protocol family 16
    Jul 13 12:37:34 ma3x kernel: cpuidle: using governor ladder
    Jul 13 12:37:34 ma3x kernel: cpuidle: using governor menu
    Jul 13 12:37:34 ma3x kernel: ACPI: bus type PCI registered
    Jul 13 12:37:34 ma3x kernel: acpiphp: ACPI Hot Plug PCI Controller Driver version: 0.5
    Jul 13 12:37:34 ma3x kernel: PCI: MMCONFIG for domain 0000 [bus 00-ff] at [mem 0xe0000000-0xefffffff] (base 0xe0000000)
    Jul 13 12:37:34 ma3x kernel: PCI: MMCONFIG at [mem 0xe0000000-0xefffffff] reserved in E820
    Jul 13 12:37:34 ma3x kernel: PCI: Using configuration type 1 for base access
    Jul 13 12:37:34 ma3x kernel: mtrr: your CPUs had inconsistent variable MTRR settings
    Jul 13 12:37:34 ma3x kernel: mtrr: probably your BIOS does not setup all CPUs.
    Jul 13 12:37:34 ma3x kernel: mtrr: corrected configuration.
    Jul 13 12:37:34 ma3x kernel: ACPI: Added _OSI(Module Device)
    Jul 13 12:37:34 ma3x kernel: ACPI: Added _OSI(Processor Device)
    Jul 13 12:37:34 ma3x kernel: ACPI: Added _OSI(3.0 _SCP Extensions)
    Jul 13 12:37:34 ma3x kernel: ACPI: Added _OSI(Processor Aggregator Device)
    Jul 13 12:37:34 ma3x kernel: ACPI: SSDT 0x00000000CFEE8300 0002F0 (v01 PmRef Cpu0Ist 00003000 INTL 20060113)
    Jul 13 12:37:34 ma3x kernel: ACPI: Dynamic OEM Table Load:
    Jul 13 12:37:34 ma3x kernel: ACPI: SSDT 0x0000000000000000 0002F0 (v01 PmRef Cpu0Ist 00003000 INTL 20060113)
    Jul 13 12:37:34 ma3x kernel: ACPI: SSDT 0x00000000CFEE87C0 000152 (v01 PmRef Cpu1Ist 00003000 INTL 20060113)
    Jul 13 12:37:34 ma3x kernel: ACPI: Dynamic OEM Table Load:
    Jul 13 12:37:34 ma3x kernel: ACPI: SSDT 0x0000000000000000 000152 (v01 PmRef Cpu1Ist 00003000 INTL 20060113)
    Jul 13 12:37:34 ma3x kernel: ACPI: Interpreter enabled
    Jul 13 12:37:34 ma3x kernel: ACPI Exception: AE_NOT_FOUND, While evaluating Sleep State [\_S2_] (20140214/hwxface-580)
    Jul 13 12:37:34 ma3x kernel: ACPI Exception: AE_NOT_FOUND, While evaluating Sleep State [\_S3_] (20140214/hwxface-580)
    Jul 13 12:37:34 ma3x kernel: ACPI: (supports S0 S1 S4 S5)
    Jul 13 12:37:34 ma3x kernel: ACPI: Using IOAPIC for interrupt routing
    Jul 13 12:37:34 ma3x kernel: PCI: Ignoring host bridge windows from ACPI; if necessary, use "pci=use_crs" and report a bug
    Jul 13 12:37:34 ma3x kernel: ACPI: PCI Root Bridge [PCI0] (domain 0000 [bus 00-ff])
    Jul 13 12:37:34 ma3x kernel: acpi PNP0A08:00: _OSC: OS supports [ExtendedConfig ASPM ClockPM Segments MSI]
    Jul 13 12:37:34 ma3x kernel: acpi PNP0A08:00: _OSC failed (AE_NOT_FOUND); disabling ASPM
    Jul 13 12:37:34 ma3x kernel: acpi PNP0A08:00: host bridge window [io 0x0000-0x0cf7] (ignored)
    Jul 13 12:37:34 ma3x kernel: acpi PNP0A08:00: host bridge window [io 0x0d00-0xffff] (ignored)
    Jul 13 12:37:34 ma3x kernel: acpi PNP0A08:00: host bridge window [mem 0x000a0000-0x000bffff] (ignored)
    Jul 13 12:37:34 ma3x kernel: acpi PNP0A08:00: host bridge window [mem 0x000c0000-0x000dffff] (ignored)
    Jul 13 12:37:34 ma3x kernel: acpi PNP0A08:00: host bridge window [mem 0xcff50000-0xfebfffff] (ignored)
    Jul 13 12:37:34 ma3x kernel: PCI: root bus 00: using default resources
    Jul 13 12:37:34 ma3x kernel: PCI host bridge to bus 0000:00
    Jul 13 12:37:34 ma3x kernel: pci_bus 0000:00: root bus resource [bus 00-ff]
    Jul 13 12:37:34 ma3x kernel: pci_bus 0000:00: root bus resource [io 0x0000-0xffff]
    Jul 13 12:37:34 ma3x kernel: pci_bus 0000:00: root bus resource [mem 0x00000000-0xfffffffff]
    Jul 13 12:37:34 ma3x kernel: pci 0000:00:00.0: [8086:29c0] type 00 class 0x060000
    Jul 13 12:37:34 ma3x kernel: pci 0000:00:01.0: [8086:29c1] type 01 class 0x060400
    Jul 13 12:37:34 ma3x kernel: pci 0000:00:01.0: PME# supported from D0 D3hot D3cold
    Jul 13 12:37:34 ma3x kernel: pci 0000:00:1a.0: [8086:2937] type 00 class 0x0c0300
    Jul 13 12:37:34 ma3x kernel: pci 0000:00:1a.0: reg 0x20: [io 0xff00-0xff1f]
    Jul 13 12:37:34 ma3x kernel: pci 0000:00:1a.0: System wakeup disabled by ACPI
    Jul 13 12:37:34 ma3x kernel: pci 0000:00:1a.1: [8086:2938] type 00 class 0x0c0300
    Jul 13 12:37:34 ma3x kernel: pci 0000:00:1a.1: reg 0x20: [io 0xfe00-0xfe1f]
    Jul 13 12:37:34 ma3x kernel: pci 0000:00:1a.1: System wakeup disabled by ACPI
    Jul 13 12:37:34 ma3x kernel: pci 0000:00:1a.2: [8086:2939] type 00 class 0x0c0300
    Jul 13 12:37:34 ma3x kernel: pci 0000:00:1a.2: reg 0x20: [io 0xfd00-0xfd1f]
    Jul 13 12:37:34 ma3x kernel: pci 0000:00:1a.2: System wakeup disabled by ACPI
    Jul 13 12:37:34 ma3x kernel: pci 0000:00:1a.7: [8086:293c] type 00 class 0x0c0320
    Jul 13 12:37:34 ma3x kernel: pci 0000:00:1a.7: reg 0x10: [mem 0xfdfff000-0xfdfff3ff]
    Jul 13 12:37:34 ma3x kernel: pci 0000:00:1a.7: PME# supported from D0 D3hot D3cold
    Jul 13 12:37:34 ma3x kernel: pci 0000:00:1a.7: System wakeup disabled by ACPI
    Jul 13 12:37:34 ma3x kernel: pci 0000:00:1b.0: [8086:293e] type 00 class 0x040300
    Jul 13 12:37:34 ma3x kernel: pci 0000:00:1b.0: reg 0x10: [mem 0xfdff8000-0xfdffbfff 64bit]
    Jul 13 12:37:34 ma3x kernel: pci 0000:00:1b.0: PME# supported from D0 D3hot D3cold
    Jul 13 12:37:34 ma3x kernel: pci 0000:00:1b.0: System wakeup disabled by ACPI
    Jul 13 12:37:34 ma3x kernel: pci 0000:00:1c.0: [8086:2940] type 01 class 0x060400
    Jul 13 12:37:34 ma3x kernel: pci 0000:00:1c.0: PME# supported from D0 D3hot D3cold
    Jul 13 12:37:34 ma3x kernel: pci 0000:00:1c.0: System wakeup disabled by ACPI
    Jul 13 12:37:34 ma3x kernel: pci 0000:00:1c.4: [8086:2948] type 01 class 0x060400
    Jul 13 12:37:34 ma3x kernel: pci 0000:00:1c.4: PME# supported from D0 D3hot D3cold
    Jul 13 12:37:34 ma3x kernel: pci 0000:00:1c.4: System wakeup disabled by ACPI
    Jul 13 12:37:34 ma3x kernel: pci 0000:00:1c.5: [8086:294a] type 01 class 0x060400
    Jul 13 12:37:34 ma3x kernel: pci 0000:00:1c.5: PME# supported from D0 D3hot D3cold
    Jul 13 12:37:34 ma3x kernel: pci 0000:00:1c.5: System wakeup disabled by ACPI
    Jul 13 12:37:34 ma3x kernel: pci 0000:00:1d.0: [8086:2934] type 00 class 0x0c0300
    Jul 13 12:37:34 ma3x kernel: pci 0000:00:1d.0: reg 0x20: [io 0xfc00-0xfc1f]
    Jul 13 12:37:34 ma3x kernel: pci 0000:00:1d.0: System wakeup disabled by ACPI
    Jul 13 12:37:34 ma3x kernel: pci 0000:00:1d.1: [8086:2935] type 00 class 0x0c0300
    Jul 13 12:37:34 ma3x kernel: pci 0000:00:1d.1: reg 0x20: [io 0xfb00-0xfb1f]
    Jul 13 12:37:34 ma3x kernel: pci 0000:00:1d.1: System wakeup disabled by ACPI
    Jul 13 12:37:34 ma3x kernel: pci 0000:00:1d.2: [8086:2936] type 00 class 0x0c0300
    Jul 13 12:37:34 ma3x kernel: pci 0000:00:1d.2: reg 0x20: [io 0xfa00-0xfa1f]
    Jul 13 12:37:34 ma3x kernel: pci 0000:00:1d.2: System wakeup disabled by ACPI
    Jul 13 12:37:34 ma3x kernel: pci 0000:00:1d.7: [8086:293a] type 00 class 0x0c0320
    Jul 13 12:37:34 ma3x kernel: pci 0000:00:1d.7: reg 0x10: [mem 0xfdffe000-0xfdffe3ff]
    Jul 13 12:37:34 ma3x kernel: pci 0000:00:1d.7: PME# supported from D0 D3hot D3cold
    Jul 13 12:37:34 ma3x kernel: pci 0000:00:1d.7: System wakeup disabled by ACPI
    Jul 13 12:37:34 ma3x kernel: pci 0000:00:1e.0: [8086:244e] type 01 class 0x060401
    Jul 13 12:37:34 ma3x kernel: pci 0000:00:1e.0: System wakeup disabled by ACPI
    Jul 13 12:37:34 ma3x kernel: pci 0000:00:1f.0: [8086:2918] type 00 class 0x060100
    Jul 13 12:37:34 ma3x kernel: pci 0000:00:1f.0: quirk: [io 0x0400-0x047f] claimed by ICH6 ACPI/GPIO/TCO
    Jul 13 12:37:34 ma3x kernel: pci 0000:00:1f.0: quirk: [io 0x0480-0x04bf] claimed by ICH6 GPIO
    Jul 13 12:37:34 ma3x kernel: pci 0000:00:1f.0: ICH7 LPC Generic IO decode 2 PIO at 0294 (mask 0003)
    Jul 13 12:37:34 ma3x kernel: pci 0000:00:1f.0: ICH7 LPC Generic IO decode 3 PIO at 0080 (mask 0003)
    Jul 13 12:37:34 ma3x kernel: pci 0000:00:1f.0: ICH7 LPC Generic IO decode 4 PIO at 0800 (mask 001f)
    Jul 13 12:37:34 ma3x kernel: pci 0000:00:1f.2: [8086:2921] type 00 class 0x01018a
    Jul 13 12:37:34 ma3x kernel: pci 0000:00:1f.2: reg 0x10: [io 0x0000-0x0007]
    Jul 13 12:37:34 ma3x kernel: pci 0000:00:1f.2: reg 0x14: [io 0x0000-0x0003]
    Jul 13 12:37:34 ma3x kernel: pci 0000:00:1f.2: reg 0x18: [io 0x0000-0x0007]
    Jul 13 12:37:34 ma3x kernel: pci 0000:00:1f.2: reg 0x1c: [io 0x0000-0x0003]
    Jul 13 12:37:34 ma3x kernel: pci 0000:00:1f.2: reg 0x20: [io 0xf900-0xf90f]
    Jul 13 12:37:34 ma3x kernel: pci 0000:00:1f.2: reg 0x24: [io 0xf800-0xf80f]
    Jul 13 12:37:34 ma3x kernel: pci 0000:00:1f.2: legacy IDE quirk: reg 0x10: [io 0x01f0-0x01f7]
    Jul 13 12:37:34 ma3x kernel: pci 0000:00:1f.2: legacy IDE quirk: reg 0x14: [io 0x03f6]
    Jul 13 12:37:34 ma3x kernel: pci 0000:00:1f.2: legacy IDE quirk: reg 0x18: [io 0x0170-0x0177]
    Jul 13 12:37:34 ma3x kernel: pci 0000:00:1f.2: legacy IDE quirk: reg 0x1c: [io 0x0376]
    Jul 13 12:37:34 ma3x kernel: pci 0000:00:1f.3: [8086:2930] type 00 class 0x0c0500
    Jul 13 12:37:34 ma3x kernel: pci 0000:00:1f.3: reg 0x10: [mem 0xfdffd000-0xfdffd0ff 64bit]
    Jul 13 12:37:34 ma3x kernel: pci 0000:00:1f.3: reg 0x20: [io 0x0500-0x051f]
    Jul 13 12:37:34 ma3x kernel: pci 0000:00:1f.5: [8086:2926] type 00 class 0x010185
    Jul 13 12:37:34 ma3x kernel: pci 0000:00:1f.5: reg 0x10: [io 0xf600-0xf607]
    Jul 13 12:37:34 ma3x kernel: pci 0000:00:1f.5: reg 0x14: [io 0xf500-0xf503]
    Jul 13 12:37:34 ma3x kernel: pci 0000:00:1f.5: reg 0x18: [io 0xf400-0xf407]
    Jul 13 12:37:34 ma3x kernel: pci 0000:00:1f.5: reg 0x1c: [io 0xf300-0xf303]
    Jul 13 12:37:34 ma3x kernel: pci 0000:00:1f.5: reg 0x20: [io 0xf200-0xf20f]
    Jul 13 12:37:34 ma3x kernel: pci 0000:00:1f.5: reg 0x24: [io 0xf100-0xf10f]
    Jul 13 12:37:34 ma3x kernel: pci 0000:01:00.0: [1002:68b8] type 00 class 0x030000
    Jul 13 12:37:34 ma3x kernel: pci 0000:01:00.0: reg 0x10: [mem 0xd0000000-0xdfffffff 64bit pref]
    Jul 13 12:37:34 ma3x kernel: pci 0000:01:00.0: reg 0x18: [mem 0xfdac0000-0xfdadffff 64bit]
    Jul 13 12:37:34 ma3x kernel: pci 0000:01:00.0: reg 0x20: [io 0xce00-0xceff]
    Jul 13 12:37:34 ma3x kernel: pci 0000:01:00.0: reg 0x30: [mem 0x00000000-0x0001ffff pref]
    Jul 13 12:37:34 ma3x kernel: pci 0000:01:00.0: supports D1 D2
    Jul 13 12:37:34 ma3x kernel: pci 0000:01:00.1: [1002:aa58] type 00 class 0x040300
    Jul 13 12:37:34 ma3x kernel: pci 0000:01:00.1: reg 0x10: [mem 0xfdafc000-0xfdafffff 64bit]
    Jul 13 12:37:34 ma3x kernel: pci 0000:01:00.1: supports D1 D2
    Jul 13 12:37:34 ma3x kernel: pci 0000:00:01.0: PCI bridge to [bus 01]
    Jul 13 12:37:34 ma3x kernel: pci 0000:00:01.0: bridge window [io 0xc000-0xcfff]
    Jul 13 12:37:34 ma3x kernel: pci 0000:00:01.0: bridge window [mem 0xfda00000-0xfdafffff]
    Jul 13 12:37:34 ma3x kernel: pci 0000:00:01.0: bridge window [mem 0xd0000000-0xdfffffff 64bit pref]
    Jul 13 12:37:34 ma3x kernel: pci 0000:00:1c.0: PCI bridge to [bus 02]
    Jul 13 12:37:34 ma3x kernel: pci 0000:00:1c.0: bridge window [io 0xb000-0xbfff]
    Jul 13 12:37:34 ma3x kernel: pci 0000:00:1c.0: bridge window [mem 0xfd700000-0xfd7fffff]
    Jul 13 12:37:34 ma3x kernel: pci 0000:00:1c.0: bridge window [mem 0xfd600000-0xfd6fffff 64bit pref]
    Jul 13 12:37:34 ma3x kernel: pci 0000:03:00.0: [10ec:8168] type 00 class 0x020000
    Jul 13 12:37:34 ma3x kernel: pci 0000:03:00.0: reg 0x10: [io 0xae00-0xaeff]
    Jul 13 12:37:34 ma3x kernel: pci 0000:03:00.0: reg 0x18: [mem 0xfdeff000-0xfdefffff 64bit]
    Jul 13 12:37:34 ma3x kernel: pci 0000:03:00.0: reg 0x30: [mem 0x00000000-0x0001ffff pref]
    Jul 13 12:37:34 ma3x kernel: pci 0000:03:00.0: supports D1 D2
    Jul 13 12:37:34 ma3x kernel: pci 0000:03:00.0: PME# supported from D1 D2 D3hot D3cold
    Jul 13 12:37:34 ma3x kernel: pci 0000:03:00.0: disabling ASPM on pre-1.1 PCIe device. You can enable it with 'pcie_aspm=force'
    Jul 13 12:37:34 ma3x kernel: pci 0000:00:1c.4: PCI bridge to [bus 03]
    Jul 13 12:37:34 ma3x kernel: pci 0000:00:1c.4: bridge window [io 0xa000-0xafff]
    Jul 13 12:37:34 ma3x kernel: pci 0000:00:1c.4: bridge window [mem 0xfde00000-0xfdefffff]
    Jul 13 12:37:34 ma3x kernel: pci 0000:00:1c.4: bridge window [mem 0xfdd00000-0xfddfffff 64bit pref]
    Jul 13 12:37:34 ma3x kernel: pci 0000:04:00.0: [197b:2363] type 00 class 0x010185
    Jul 13 12:37:34 ma3x kernel: pci 0000:04:00.0: reg 0x24: [mem 0xfdcfe000-0xfdcfffff]
    Jul 13 12:37:34 ma3x kernel: pci 0000:04:00.0: PME# supported from D3hot
    Jul 13 12:37:34 ma3x kernel: pci 0000:04:00.1: [197b:2363] type 00 class 0x010185
    Jul 13 12:37:34 ma3x kernel: pci 0000:04:00.1: reg 0x10: [io 0xdf00-0xdf07]
    Jul 13 12:37:34 ma3x kernel: pci 0000:04:00.1: reg 0x14: [io 0xde00-0xde03]
    Jul 13 12:37:34 ma3x kernel: pci 0000:04:00.1: reg 0x18: [io 0xdd00-0xdd07]
    Jul 13 12:37:34 ma3x kernel: pci 0000:04:00.1: reg 0x1c: [io 0xdc00-0xdc03]
    Jul 13 12:37:34 ma3x kernel: pci 0000:04:00.1: reg 0x20: [io 0xdb00-0xdb0f]
    Jul 13 12:37:34 ma3x kernel: pci 0000:04:00.0: disabling ASPM on pre-1.1 PCIe device. You can enable it with 'pcie_aspm=force'
    Jul 13 12:37:34 ma3x kernel: pci 0000:00:1c.5: PCI bridge to [bus 04]
    Jul 13 12:37:34 ma3x kernel: pci 0000:00:1c.5: bridge window [io 0xd000-0xdfff]
    Jul 13 12:37:34 ma3x kernel: pci 0000:00:1c.5: bridge window [mem 0xfdc00000-0xfdcfffff]
    Jul 13 12:37:34 ma3x kernel: pci 0000:00:1c.5: bridge window [mem 0xfdb00000-0xfdbfffff 64bit pref]
    Jul 13 12:37:34 ma3x kernel: pci 0000:05:00.0: [10ec:8139] type 00 class 0x020000
    Jul 13 12:37:34 ma3x kernel: pci 0000:05:00.0: reg 0x10: [io 0xee00-0xeeff]
    Jul 13 12:37:34 ma3x kernel: pci 0000:05:00.0: reg 0x14: [mem 0xfd9ff000-0xfd9ff0ff]
    Jul 13 12:37:34 ma3x kernel: pci 0000:05:00.0: supports D1 D2
    Jul 13 12:37:34 ma3x kernel: pci 0000:05:00.0: PME# supported from D0 D1 D2 D3hot
    Jul 13 12:37:34 ma3x kernel: pci 0000:00:1e.0: PCI bridge to [bus 05] (subtractive decode)
    Jul 13 12:37:34 ma3x kernel: pci 0000:00:1e.0: bridge window [io 0xe000-0xefff]
    Jul 13 12:37:34 ma3x kernel: pci 0000:00:1e.0: bridge window [mem 0xfd900000-0xfd9fffff]
    Jul 13 12:37:34 ma3x kernel: pci 0000:00:1e.0: bridge window [mem 0xfd800000-0xfd8fffff 64bit pref]
    Jul 13 12:37:34 ma3x kernel: pci 0000:00:1e.0: bridge window [io 0x0000-0xffff] (subtractive decode)
    Jul 13 12:37:34 ma3x kernel: pci 0000:00:1e.0: bridge window [mem 0x00000000-0xfffffffff] (subtractive decode)
    Jul 13 12:37:34 ma3x kernel: ACPI: PCI Interrupt Link [LNKA] (IRQs *5 7 9 10 11 12 14 15)
    Jul 13 12:37:34 ma3x kernel: ACPI: PCI Interrupt Link [LNKB] (IRQs 5 7 9 *10 11 12 14 15)
    Jul 13 12:37:34 ma3x kernel: ACPI: PCI Interrupt Link [LNKC] (IRQs 5 7 9 *10 11 12 14 15)
    Jul 13 12:37:34 ma3x kernel: ACPI: PCI Interrupt Link [LNKD] (IRQs 5 7 9 10 *11 12 14 15)
    Jul 13 12:37:34 ma3x kernel: ACPI: PCI Interrupt Link [LNKE] (IRQs 5 7 9 10 11 12 14 15) *0, disabled.
    Jul 13 12:37:34 ma3x kernel: ACPI: PCI Interrupt Link [LNKF] (IRQs 5 *7 9 10 11 12 14 15)
    Jul 13 12:37:34 ma3x kernel: ACPI: PCI Interrupt Link [LNK0] (IRQs 5 7 *9 10 11 12 14 15)
    Jul 13 12:37:34 ma3x kernel: ACPI: PCI Interrupt Link [LNK1] (IRQs 5 7 9 10 *11 12 14 15)
    Jul 13 12:37:34 ma3x kernel: ACPI: Enabled 1 GPEs in block 00 to 3F
    Jul 13 12:37:34 ma3x kernel: vgaarb: device added: PCI:0000:01:00.0,decodes=io+mem,owns=io+mem,locks=none
    Jul 13 12:37:34 ma3x kernel: vgaarb: loaded
    Jul 13 12:37:34 ma3x kernel: vgaarb: bridge control possible 0000:01:00.0
    Jul 13 12:37:34 ma3x kernel: PCI: Using ACPI for IRQ routing
    Jul 13 12:37:34 ma3x kernel: PCI: pci_cache_line_size set to 64 bytes
    Jul 13 12:37:34 ma3x kernel: e820: reserve RAM buffer [mem 0x0009f400-0x0009ffff]
    Jul 13 12:37:34 ma3x kernel: e820: reserve RAM buffer [mem 0xcfe90000-0xcfffffff]
    Jul 13 12:37:34 ma3x kernel: NetLabel: Initializing
    Jul 13 12:37:34 ma3x kernel: NetLabel: domain hash size = 128
    Jul 13 12:37:34 ma3x kernel: NetLabel: protocols = UNLABELED CIPSOv4
    Jul 13 12:37:34 ma3x kernel: NetLabel: unlabeled traffic allowed by default
    Jul 13 12:37:34 ma3x kernel: Switched to clocksource refined-jiffies
    Jul 13 12:37:34 ma3x kernel: pnp: PnP ACPI init
    Jul 13 12:37:34 ma3x kernel: ACPI: bus type PNP registered
    Jul 13 12:37:34 ma3x kernel: system 00:00: [io 0x04d0-0x04d1] has been reserved
    Jul 13 12:37:34 ma3x kernel: system 00:00: [io 0x0290-0x029f] has been reserved
    Jul 13 12:37:34 ma3x kernel: system 00:00: [io 0x0800-0x0805] has been reserved
    Jul 13 12:37:34 ma3x kernel: system 00:00: [io 0x0290-0x0297] has been reserved
    Jul 13 12:37:34 ma3x kernel: system 00:00: [io 0x0880-0x088f] has been reserved
    Jul 13 12:37:34 ma3x kernel: system 00:00: Plug and Play ACPI device, IDs PNP0c02 (active)
    Jul 13 12:37:34 ma3x kernel: pnp 00:01: [dma 4]
    Jul 13 12:37:34 ma3x kernel: pnp 00:01: Plug and Play ACPI device, IDs PNP0200 (active)
    Jul 13 12:37:34 ma3x kernel: pnp 00:02: Plug and Play ACPI device, IDs PNP0b00 (active)
    Jul 13 12:37:34 ma3x kernel: pnp 00:03: Plug and Play ACPI device, IDs PNP0800 (active)
    Jul 13 12:37:34 ma3x kernel: pnp 00:04: Plug and Play ACPI device, IDs PNP0c04 (active)
    Jul 13 12:37:34 ma3x kernel: pnp 00:05: [dma 2]
    Jul 13 12:37:34 ma3x kernel: pnp 00:05: Plug and Play ACPI device, IDs PNP0700 (active)
    Jul 13 12:37:34 ma3x kernel: pnp 00:06: Plug and Play ACPI device, IDs PNP0501 (active)
    Jul 13 12:37:34 ma3x kernel: pnp 00:07: Plug and Play ACPI device, IDs PNP0400 (active)
    Jul 13 12:37:34 ma3x kernel: pnp 00:08: Plug and Play ACPI device, IDs PNP0303 PNP030b (active)
    Jul 13 12:37:34 ma3x kernel: system 00:09: [io 0x0400-0x04bf] could not be reserved
    Jul 13 12:37:34 ma3x kernel: system 00:09: Plug and Play ACPI device, IDs PNP0c02 (active)
    Jul 13 12:37:34 ma3x kernel: pnp 00:0a: Plug and Play ACPI device, IDs INT0800 (active)
    Jul 13 12:37:34 ma3x kernel: system 00:0b: [mem 0xe0000000-0xefffffff] has been reserved
    Jul 13 12:37:34 ma3x kernel: system 00:0b: Plug and Play ACPI device, IDs PNP0c02 (active)
    Jul 13 12:37:34 ma3x kernel: system 00:0c: [mem 0x000f0000-0x000fffff] could not be reserved
    Jul 13 12:37:34 ma3x kernel: system 00:0c: [mem 0xcff00000-0xcfffffff] could not be reserved
    Jul 13 12:37:34 ma3x kernel: system 00:0c: [mem 0xcfee0000-0xcfefffff] could not be reserved
    Jul 13 12:37:34 ma3x kernel: system 00:0c: [mem 0x00000000-0x0009ffff] could not be reserved
    Jul 13 12:37:34 ma3x kernel: system 00:0c: [mem 0x00100000-0xcfedffff] could not be reserved
    Jul 13 12:37:34 ma3x kernel: system 00:0c: [mem 0xfec00000-0xfec00fff] could not be reserved
    Jul 13 12:37:34 ma3x kernel: system 00:0c: [mem 0xfed14000-0xfed1dfff] has been reserved
    Jul 13 12:37:34 ma3x kernel: system 00:0c: [mem 0xfed20000-0xfed9ffff] has been reserved
    Jul 13 12:37:34 ma3x kernel: system 00:0c: [mem 0xfee00000-0xfee00fff] has been reserved
    Jul 13 12:37:34 ma3x kernel: system 00:0c: [mem 0xffb00000-0xffb7ffff] has been reserved
    Jul 13 12:37:34 ma3x kernel: system 00:0c: [mem 0xfff00000-0xffffffff] has been reserved
    Jul 13 12:37:34 ma3x kernel: system 00:0c: [mem 0x000e0000-0x000effff] has been reserved
    Jul 13 12:37:34 ma3x kernel: system 00:0c: Plug and Play ACPI device, IDs PNP0c01 (active)
    Jul 13 12:37:34 ma3x kernel: pnp: PnP ACPI: found 13 devices
    Jul 13 12:37:34 ma3x kernel: ACPI: bus type PNP unregistered
    Jul 13 12:37:34 ma3x kernel: Switched to clocksource acpi_pm
    Jul 13 12:37:34 ma3x kernel: pci 0000:01:00.0: BAR 6: assigned [mem 0xfda00000-0xfda1ffff pref]
    Jul 13 12:37:34 ma3x kernel: pci 0000:00:01.0: PCI bridge to [bus 01]
    Jul 13 12:37:34 ma3x kernel: pci 0000:00:01.0: bridge window [io 0xc000-0xcfff]
    Jul 13 12:37:34 ma3x kernel: pci 0000:00:01.0: bridge window [mem 0xfda00000-0xfdafffff]
    Jul 13 12:37:34 ma3x kernel: pci 0000:00:01.0: bridge window [mem 0xd0000000-0xdfffffff 64bit pref]
    Jul 13 12:37:34 ma3x kernel: pci 0000:00:1c.0: PCI bridge to [bus 02]
    Jul 13 12:37:34 ma3x kernel: pci 0000:00:1c.0: bridge window [io 0xb000-0xbfff]
    Jul 13 12:37:34 ma3x kernel: pci 0000:00:1c.0: bridge window [mem 0xfd700000-0xfd7fffff]
    Jul 13 12:37:34 ma3x kernel: pci 0000:00:1c.0: bridge window [mem 0xfd600000-0xfd6fffff 64bit pref]
    Jul 13 12:37:34 ma3x kernel: pci 0000:03:00.0: BAR 6: assigned [mem 0xfdd00000-0xfdd1ffff pref]
    Jul 13 12:37:34 ma3x kernel: pci 0000:00:1c.4: PCI bridge to [bus 03]
    Jul 13 12:37:34 ma3x kernel: pci 0000:00:1c.4: bridge window [io 0xa000-0xafff]
    Jul 13 12:37:34 ma3x kernel: pci 0000:00:1c.4: bridge window [mem 0xfde00000-0xfdefffff]
    Jul 13 12:37:34 ma3x kernel: pci 0000:00:1c.4: bridge window [mem 0xfdd00000-0xfddfffff 64bit pref]
    Jul 13 12:37:34 ma3x kernel: pci 0000:00:1c.5: PCI bridge to [bus 04]
    Jul 13 12:37:34 ma3x kernel: pci 0000:00:1c.5: bridge window [io 0xd000-0xdfff]
    Jul 13 12:37:34 ma3x kernel: pci 0000:00:1c.5: bridge window [mem 0xfdc00000-0xfdcfffff]
    Jul 13 12:37:34 ma3x kernel: pci 0000:00:1c.5: bridge window [mem 0xfdb00000-0xfdbfffff 64bit pref]
    Jul 13 12:37:34 ma3x kernel: pci 0000:00:1e.0: PCI bridge to [bus 05]
    Jul 13 12:37:34 ma3x kernel: pci 0000:00:1e.0: bridge window [io 0xe000-0xefff]
    Jul 13 12:37:34 ma3x kernel: pci 0000:00:1e.0: bridge window [mem 0xfd900000-0xfd9fffff]
    Jul 13 12:37:34 ma3x kernel: pci 0000:00:1e.0: bridge window [mem 0xfd800000-0xfd8fffff 64bit pref]
    Jul 13 12:37:34 ma3x kernel: pci_bus 0000:00: resource 4 [io 0x0000-0xffff]
    Jul 13 12:37:34 ma3x kernel: pci_bus 0000:00: resource 5 [mem 0x00000000-0xfffffffff]
    Jul 13 12:37:34 ma3x kernel: pci_bus 0000:01: resource 0 [io 0xc000-0xcfff]
    Jul 13 12:37:34 ma3x kernel: pci_bus 0000:01: resource 1 [mem 0xfda00000-0xfdafffff]
    Jul 13 12:37:34 ma3x kernel: pci_bus 0000:01: resource 2 [mem 0xd0000000-0xdfffffff 64bit pref]
    Jul 13 12:37:34 ma3x kernel: pci_bus 0000:02: resource 0 [io 0xb000-0xbfff]
    Jul 13 12:37:34 ma3x kernel: pci_bus 0000:02: resource 1 [mem 0xfd700000-0xfd7fffff]
    Jul 13 12:37:34 ma3x kernel: pci_bus 0000:02: resource 2 [mem 0xfd600000-0xfd6fffff 64bit pref]
    Jul 13 12:37:34 ma3x kernel: pci_bus 0000:03: resource 0 [io 0xa000-0xafff]
    Jul 13 12:37:34 ma3x kernel: pci_bus 0000:03: resource 1 [mem 0xfde00000-0xfdefffff]
    Jul 13 12:37:34 ma3x kernel: pci_bus 0000:03: resource 2 [mem 0xfdd00000-0xfddfffff 64bit pref]
    Jul 13 12:37:34 ma3x kernel: pci_bus 0000:04: resource 0 [io 0xd000-0xdfff]
    Jul 13 12:37:34 ma3x kernel: pci_bus 0000:04: resource 1 [mem 0xfdc00000-0xfdcfffff]
    Jul 13 12:37:34 ma3x kernel: pci_bus 0000:04: resource 2 [mem 0xfdb00000-0xfdbfffff 64bit pref]
    Jul 13 12:37:34 ma3x kernel: pci_bus 0000:05: resource 0 [io 0xe000-0xefff]
    Jul 13 12:37:34 ma3x kernel: pci_bus 0000:05: resource 1 [mem 0xfd900000-0xfd9fffff]
    Jul 13 12:37:34 ma3x kernel: pci_bus 0000:05: resource 2 [mem 0xfd800000-0xfd8fffff 64bit pref]
    Jul 13 12:37:34 ma3x kernel: pci_bus 0000:05: resource 4 [io 0x0000-0xffff]
    Jul 13 12:37:34 ma3x kernel: pci_bus 0000:05: resource 5 [mem 0x00000000-0xfffffffff]
    Jul 13 12:37:34 ma3x kernel: NET: Registered protocol family 2
    Jul 13 12:37:34 ma3x kernel: TCP established hash table entries: 32768 (order: 6, 262144 bytes)
    Jul 13 12:37:34 ma3x kernel: TCP bind hash table entries: 32768 (order: 7, 524288 bytes)
    Jul 13 12:37:34 ma3x kernel: TCP: Hash tables configured (established 32768 bind 32768)
    Jul 13 12:37:34 ma3x kernel: TCP: reno registered
    Jul 13 12:37:34 ma3x kernel: UDP hash table entries: 2048 (order: 4, 65536 bytes)
    Jul 13 12:37:34 ma3x kernel: UDP-Lite hash table entries: 2048 (order: 4, 65536 bytes)
    Jul 13 12:37:34 ma3x kernel: NET: Registered protocol family 1
    Jul 13 12:37:34 ma3x kernel: pci 0000:01:00.0: Boot video device
    Jul 13 12:37:34 ma3x kernel: PCI: CLS 64 bytes, default 64
    Jul 13 12:37:34 ma3x kernel: Unpacking initramfs...
    Jul 13 12:37:34 ma3x kernel: Freeing initrd memory: 3172K (ffff8800379be000 - ffff880037cd7000)
    Jul 13 12:37:34 ma3x kernel: PCI-DMA: Using software bounce buffering for IO (SWIOTLB)
    Jul 13 12:37:34 ma3x kernel: software IO TLB [mem 0xcbe90000-0xcfe90000] (64MB) mapped at [ffff8800cbe90000-ffff8800cfe8ffff]
    Jul 13 12:37:34 ma3x kernel: Scanning for low memory corruption every 60 seconds
    Jul 13 12:37:34 ma3x kernel: futex hash table entries: 1024 (order: 4, 65536 bytes)
    Jul 13 12:37:34 ma3x kernel: HugeTLB registered 2 MB page size, pre-allocated 0 pages
    Jul 13 12:37:34 ma3x kernel: zbud: loaded
    Jul 13 12:37:34 ma3x kernel: VFS: Disk quotas dquot_6.5.2
    Jul 13 12:37:34 ma3x kernel: Dquot-cache hash table entries: 512 (order 0, 4096 bytes)
    Jul 13 12:37:34 ma3x kernel: msgmni has been set to 7907
    Jul 13 12:37:34 ma3x kernel: Key type big_key registered
    Jul 13 12:37:34 ma3x kernel: Block layer SCSI generic (bsg) driver version 0.4 loaded (major 252)
    Jul 13 12:37:34 ma3x kernel: io scheduler noop registered
    Jul 13 12:37:34 ma3x kernel: io scheduler deadline registered
    Jul 13 12:37:34 ma3x kernel: io scheduler cfq registered (default)
    Jul 13 12:37:34 ma3x kernel: pcieport 0000:00:01.0: irq 40 for MSI/MSI-X
    Jul 13 12:37:34 ma3x kernel: pcieport 0000:00:1c.0: irq 41 for MSI/MSI-X
    Jul 13 12:37:34 ma3x kernel: pcieport 0000:00:1c.4: irq 42 for MSI/MSI-X
    Jul 13 12:37:34 ma3x kernel: pcieport 0000:00:1c.5: irq 43 for MSI/MSI-X
    Jul 13 12:37:34 ma3x kernel: pci_hotplug: PCI Hot Plug PCI Core version: 0.5
    Jul 13 12:37:34 ma3x kernel: pciehp: PCI Express Hot Plug Controller Driver version: 0.4
    Jul 13 12:37:34 ma3x kernel: vesafb: mode is 1280x1024x32, linelength=5120, pages=0
    Jul 13 12:37:34 ma3x kernel: vesafb: scrolling: redraw
    Jul 13 12:37:34 ma3x kernel: vesafb: Truecolor: size=0:8:8:8, shift=0:16:8:0
    Jul 13 12:37:34 ma3x kernel: vesafb: framebuffer at 0xd0000000, mapped to 0xffffc90010780000, using 5120k, total 5120k
    Jul 13 12:37:34 ma3x kernel: Console: switching to colour frame buffer device 160x64
    Jul 13 12:37:34 ma3x kernel: fb0: VESA VGA frame buffer device
    Jul 13 12:37:34 ma3x kernel: intel_idle: does not run on family 6 model 23
    Jul 13 12:37:34 ma3x kernel: GHES: HEST is not enabled!
    Jul 13 12:37:34 ma3x kernel: Serial: 8250/16550 driver, 4 ports, IRQ sharing disabled
    Jul 13 12:37:34 ma3x kernel: 00:06: ttyS0 at I/O 0x3f8 (irq = 4, base_baud = 115200) is a 16550A
    Jul 13 12:37:34 ma3x kernel: Linux agpgart interface v0.103
    Jul 13 12:37:34 ma3x kernel: rtc_cmos 00:02: RTC can wake from S4
    Jul 13 12:37:34 ma3x kernel: rtc_cmos 00:02: rtc core: registered rtc_cmos as rtc0
    Jul 13 12:37:34 ma3x kernel: rtc_cmos 00:02: alarms up to one month, 242 bytes nvram
    Jul 13 12:37:34 ma3x kernel: ledtrig-cpu: registered to indicate activity on CPUs
    Jul 13 12:37:34 ma3x kernel: TCP: cubic registered
    Jul 13 12:37:34 ma3x kernel: NET: Registered protocol family 10
    Jul 13 12:37:34 ma3x kernel: NET: Registered protocol family 17
    Jul 13 12:37:34 ma3x kernel: registered taskstats version 1
    Jul 13 12:37:34 ma3x kernel: Magic number: 6:516:626
    Jul 13 12:37:34 ma3x kernel: pci 0000:00:1b.0: hash matches
    Jul 13 12:37:34 ma3x kernel: rtc_cmos 00:02: setting system clock to 2014-07-13 09:37:31 UTC (1405244251)
    Jul 13 12:37:34 ma3x kernel: PM: Hibernation image not present or could not be loaded.
    Jul 13 12:37:34 ma3x kernel: Freeing unused kernel memory: 1116K (ffffffff818df000 - ffffffff819f6000)
    Jul 13 12:37:34 ma3x kernel: Write protecting the kernel read-only data: 8192k
    Jul 13 12:37:34 ma3x kernel: Freeing unused kernel memory: 908K (ffff88000151d000 - ffff880001600000)
    Jul 13 12:37:34 ma3x kernel: Freeing unused kernel memory: 404K (ffff88000179b000 - ffff880001800000)
    Jul 13 12:37:34 ma3x kernel: random: systemd-tmpfile urandom read with 2 bits of entropy available
    Jul 13 12:37:34 ma3x systemd-udevd[47]: starting version 214
    Jul 13 12:37:34 ma3x kernel: i8042: PNP: PS/2 Controller [PNP0303:PS2K] at 0x60,0x64 irq 1
    Jul 13 12:37:34 ma3x kernel: i8042: PNP: PS/2 appears to have AUX port disabled, if this is incorrect please boot with i8042.nopnp
    Jul 13 12:37:34 ma3x kernel: serio: i8042 KBD port at 0x60,0x64 irq 1
    Jul 13 12:37:34 ma3x kernel: ACPI: bus type USB registered
    Jul 13 12:37:34 ma3x kernel: usbcore: registered new interface driver usbfs
    Jul 13 12:37:34 ma3x kernel: usbcore: registered new interface driver hub
    Jul 13 12:37:34 ma3x kernel: usbcore: registered new device driver usb
    Jul 13 12:37:34 ma3x kernel: ehci_hcd: USB 2.0 'Enhanced' Host Controller (EHCI) Driver
    Jul 13 12:37:34 ma3x kernel: ehci-pci: EHCI PCI platform driver
    Jul 13 12:37:34 ma3x kernel: ehci-pci 0000:00:1a.7: EHCI Host Controller
    Jul 13 12:37:34 ma3x kernel: ehci-pci 0000:00:1a.7: new USB bus registered, assigned bus number 1
    Jul 13 12:37:34 ma3x kernel: uhci_hcd: USB Universal Host Controller Interface driver
    Jul 13 12:37:34 ma3x kernel: SCSI subsystem initialized
    Jul 13 12:37:34 ma3x kernel: libata version 3.00 loaded.
    Jul 13 12:37:34 ma3x kernel: pata_jmicron 0000:04:00.1: enabling device (0000 -> 0001)
    Jul 13 12:37:34 ma3x kernel: scsi0 : pata_jmicron
    Jul 13 12:37:34 ma3x kernel: scsi1 : pata_jmicron
    Jul 13 12:37:34 ma3x kernel: ehci-pci 0000:00:1a.7: cache line size of 64 is not supported
    Jul 13 12:37:34 ma3x kernel: ehci-pci 0000:00:1a.7: irq 18, io mem 0xfdfff000
    Jul 13 12:37:34 ma3x kernel: ata1: PATA max UDMA/100 cmd 0xdf00 ctl 0xde00 bmdma 0xdb00 irq 18
    Jul 13 12:37:34 ma3x kernel: ata2: PATA max UDMA/100 cmd 0xdd00 ctl 0xdc00 bmdma 0xdb08 irq 18
    Jul 13 12:37:34 ma3x kernel: ahci 0000:04:00.0: version 3.0
    Jul 13 12:37:34 ma3x kernel: FDC 0 is a post-1991 82077
    Jul 13 12:37:34 ma3x kernel: ehci-pci 0000:00:1a.7: USB 2.0 started, EHCI 1.00
    Jul 13 12:37:34 ma3x kernel: hub 1-0:1.0: USB hub found
    Jul 13 12:37:34 ma3x kernel: hub 1-0:1.0: 6 ports detected
    Jul 13 12:37:34 ma3x kernel: ehci-pci 0000:00:1d.7: EHCI Host Controller
    Jul 13 12:37:34 ma3x kernel: ehci-pci 0000:00:1d.7: new USB bus registered, assigned bus number 2
    Jul 13 12:37:34 ma3x kernel: ahci 0000:04:00.0: AHCI 0001.0000 32 slots 2 ports 3 Gbps 0x3 impl SATA mode
    Jul 13 12:37:34 ma3x kernel: ahci 0000:04:00.0: flags: 64bit ncq pm led clo pmp pio slum part
    Jul 13 12:37:34 ma3x kernel: ehci-pci 0000:00:1d.7: cache line size of 64 is not supported
    Jul 13 12:37:34 ma3x kernel: ehci-pci 0000:00:1d.7: irq 23, io mem 0xfdffe000
    Jul 13 12:37:34 ma3x kernel: scsi2 : ahci
    Jul 13 12:37:34 ma3x kernel: scsi3 : ahci
    Jul 13 12:37:34 ma3x kernel: ata3: SATA max UDMA/133 abar m8192@0xfdcfe000 port 0xfdcfe100 irq 17
    Jul 13 12:37:34 ma3x kernel: ata4: SATA max UDMA/133 abar m8192@0xfdcfe000 port 0xfdcfe180 irq 17
    Jul 13 12:37:34 ma3x kernel: ehci-pci 0000:00:1d.7: USB 2.0 started, EHCI 1.00
    Jul 13 12:37:34 ma3x kernel: hub 2-0:1.0: USB hub found
    Jul 13 12:37:34 ma3x kernel: hub 2-0:1.0: 6 ports detected
    Jul 13 12:37:34 ma3x kernel: uhci_hcd 0000:00:1a.0: UHCI Host Controller
    Jul 13 12:37:34 ma3x kernel: uhci_hcd 0000:00:1a.0: new USB bus registered, assigned bus number 3
    Jul 13 12:37:34 ma3x kernel: uhci_hcd 0000:00:1a.0: detected 2 ports
    Jul 13 12:37:34 ma3x kernel: uhci_hcd 0000:00:1a.0: irq 16, io base 0x0000ff00
    Jul 13 12:37:34 ma3x kernel: hub 3-0:1.0: USB hub found
    Jul 13 12:37:34 ma3x kernel: hub 3-0:1.0: 2 ports detected
    Jul 13 12:37:34 ma3x kernel: ata_piix 0000:00:1f.2: version 2.13
    Jul 13 12:37:34 ma3x kernel: ata_piix 0000:00:1f.2: MAP [ P0 -- P1 -- ]
    Jul 13 12:37:34 ma3x kernel: scsi4 : ata_piix
    Jul 13 12:37:34 ma3x kernel: scsi5 : ata_piix
    Jul 13 12:37:34 ma3x kernel: ata5: SATA max UDMA/133 cmd 0x1f0 ctl 0x3f6 bmdma 0xf900 irq 14
    Jul 13 12:37:34 ma3x kernel: ata6: SATA max UDMA/133 cmd 0x170 ctl 0x376 bmdma 0xf908 irq 15
    Jul 13 12:37:34 ma3x kernel: ata_piix 0000:00:1f.5: MAP [ P0 -- P1 -- ]
    Jul 13 12:37:34 ma3x kernel: scsi6 : ata_piix
    Jul 13 12:37:34 ma3x kernel: scsi7 : ata_piix
    Jul 13 12:37:34 ma3x kernel: ata7: SATA max UDMA/133 cmd 0xf600 ctl 0xf500 bmdma 0xf200 irq 19
    Jul 13 12:37:34 ma3x kernel: ata8: SATA max UDMA/133 cmd 0xf400 ctl 0xf300 bmdma 0xf208 irq 19
    Jul 13 12:37:34 ma3x kernel: uhci_hcd 0000:00:1a.1: UHCI Host Controller
    Jul 13 12:37:34 ma3x kernel: uhci_hcd 0000:00:1a.1: new USB bus registered, assigned bus number 4
    Jul 13 12:37:34 ma3x kernel: uhci_hcd 0000:00:1a.1: detected 2 ports
    Jul 13 12:37:34 ma3x kernel: uhci_hcd 0000:00:1a.1: irq 21, io base 0x0000fe00
    Jul 13 12:37:34 ma3x kernel: hub 4-0:1.0: USB hub found
    Jul 13 12:37:34 ma3x kernel: hub 4-0:1.0: 2 ports detected
    Jul 13 12:37:34 ma3x kernel: uhci_hcd 0000:00:1a.2: UHCI Host Controller
    Jul 13 12:37:34 ma3x kernel: uhci_hcd 0000:00:1a.2: new USB bus registered, assigned bus number 5
    Jul 13 12:37:34 ma3x kernel: uhci_hcd 0000:00:1a.2: detected 2 ports
    Jul 13 12:37:34 ma3x kernel: uhci_hcd 0000:00:1a.2: irq 19, io base 0x0000fd00
    Jul 13 12:37:34 ma3x kernel: hub 5-0:1.0: USB hub found
    Jul 13 12:37:34 ma3x kernel: hub 5-0:1.0: 2 ports detected
    Jul 13 12:37:34 ma3x kernel: uhci_hcd 0000:00:1d.0: UHCI Host Controller
    Jul 13 12:37:34 ma3x kernel: uhci_hcd 0000:00:1d.0: new USB bus registered, assigned bus number 6
    Jul 13 12:37:34 ma3x kernel: uhci_hcd 0000:00:1d.0: detected 2 ports
    Jul 13 12:37:34 ma3x kernel: uhci_hcd 0000:00:1d.0: irq 23, io base 0x0000fc00
    Jul 13 12:37:34 ma3x kernel: hub 6-0:1.0: USB hub found
    Jul 13 12:37:34 ma3x kernel: hub 6-0:1.0: 2 ports detected
    Jul 13 12:37:34 ma3x kernel: uhci_hcd 0000:00:1d.1: UHCI Host Controller
    Jul 13 12:37:34 ma3x kernel: uhci_hcd 0000:00:1d.1: new USB bus registered, assigned bus number 7
    Jul 13 12:37:34 ma3x kernel: uhci_hcd 0000:00:1d.1: detected 2 ports
    Jul 13 12:37:34 ma3x kernel: uhci_hcd 0000:00:1d.1: irq 19, io base 0x0000fb00
    Jul 13 12:37:34 ma3x kernel: hub 7-0:1.0: USB hub found
    Jul 13 12:37:34 ma3x kernel: hub 7-0:1.0: 2 ports detected
    Jul 13 12:37:34 ma3x kernel: uhci_hcd 0000:00:1d.2: UHCI Host Controller
    Jul 13 12:37:34 ma3x kernel: uhci_hcd 0000:00:1d.2: new USB bus registered, assigned bus number 8
    Jul 13 12:37:34 ma3x kernel: uhci_hcd 0000:00:1d.2: detected 2 ports
    Jul 13 12:37:34 ma3x kernel: uhci_hcd 0000:00:1d.2: irq 18, io base 0x0000fa00
    Jul 13 12:37:34 ma3x kernel: hub 8-0:1.0: USB hub found
    Jul 13 12:37:34 ma3x kernel: hub 8-0:1.0: 2 ports detected
    Jul 13 12:37:34 ma3x kernel: input: AT Translated Set 2 keyboard as /devices/platform/i8042/serio0/input/input0
    Jul 13 12:37:34 ma3x kernel: ata1.00: ATAPI: HL-DT-ST DVDRAM GSA-H10N, JL10, max UDMA/33
    Jul 13 12:37:34 ma3x kernel: ata1.00: configured for UDMA/33
    Jul 13 12:37:34 ma3x kernel: scsi 0:0:0:0: CD-ROM HL-DT-ST DVDRAM GSA-H10N JL10 PQ: 0 ANSI: 5
    Jul 13 12:37:34 ma3x kernel: ata3: SATA link down (SStatus 0 SControl 300)
    Jul 13 12:37:34 ma3x kernel: ata4: SATA link down (SStatus 0 SControl 300)
    Jul 13 12:37:34 ma3x kernel: ata8: SATA link down (SStatus 0 SControl 300)
    Jul 13 12:37:34 ma3x kernel: ata6: SATA link down (SStatus 0 SControl 300)
    Jul 13 12:37:34 ma3x kernel: ata7: SATA link down (SStatus 0 SControl 300)
    Jul 13 12:37:34 ma3x kernel: ata5: SATA link up 3.0 Gbps (SStatus 123 SControl 300)
    Jul 13 12:37:34 ma3x kernel: ata5.00: ATA-8: WDC WD5000AAKS-00A7B0, 01.03B01, max UDMA/133
    Jul 13 12:37:34 ma3x kernel: ata5.00: 976773168 sectors, multi 16: LBA48 NCQ (depth 0/32)
    Jul 13 12:37:34 ma3x kernel: ata5.00: configured for UDMA/133
    Jul 13 12:37:34 ma3x kernel: scsi 4:0:0:0: Direct-Access ATA WDC WD5000AAKS-0 01.0 PQ: 0 ANSI: 5
    Jul 13 12:37:34 ma3x kernel: sr0: scsi3-mmc drive: 48x/48x writer dvd-ram cd/rw xa/form2 cdda tray
    Jul 13 12:37:34 ma3x kernel: cdrom: Uniform CD-ROM driver Revision: 3.20
    Jul 13 12:37:34 ma3x kernel: sr 0:0:0:0: Attached scsi CD-ROM sr0
    Jul 13 12:37:34 ma3x kernel: sd 4:0:0:0: [sda] 976773168 512-byte logical blocks: (500 GB/465 GiB)
    Jul 13 12:37:34 ma3x kernel: sd 4:0:0:0: [sda] Write Protect is off
    Jul 13 12:37:34 ma3x kernel: sd 4:0:0:0: [sda] Mode Sense: 00 3a 00 00
    Jul 13 12:37:34 ma3x kernel: sd 4:0:0:0: [sda] Write cache: enabled, read cache: enabled, doesn't support DPO or FUA
    Jul 13 12:37:34 ma3x kernel: usb 2-6: new high-speed USB device number 3 using ehci-pci
    Jul 13 12:37:34 ma3x kernel: sda: sda1 sda2 sda3 sda4 < sda5 sda6 sda7 sda8 >
    Jul 13 12:37:34 ma3x kernel: sd 4:0:0:0: [sda] Attached SCSI disk
    Jul 13 12:37:34 ma3x kernel: hub 2-6:1.0: USB hub found
    Jul 13 12:37:34 ma3x kernel: hub 2-6:1.0: 4 ports detected
    Jul 13 12:37:34 ma3x kernel: tsc: Refined TSC clocksource calibration: 3012.484 MHz
    Jul 13 12:37:34 ma3x kernel: usb 8-1: new full-speed USB device number 2 using uhci_hcd
    Jul 13 12:37:34 ma3x kernel: hidraw: raw HID events driver (C) Jiri Kosina
    Jul 13 12:37:34 ma3x kernel: usbcore: registered new interface driver usbhid
    Jul 13 12:37:34 ma3x kernel: usbhid: USB HID core driver
    Jul 13 12:37:34 ma3x kernel: input: Razer Razer Abyssus as /devices/pci0000:00/0000:00:1d.2/usb8/8-1/8-1:1.0/0003:1532:001C.0001/input/input1
    Jul 13 12:37:34 ma3x kernel: hid-generic 0003:1532:001C.0001: input,hidraw0: USB HID v1.11 Mouse [Razer Razer Abyssus] on usb-0000:00:1d.2-1/input0
    Jul 13 12:37:34 ma3x kernel: EXT4-fs (sda6): mounted filesystem with ordered data mode. Opts: (null)
    Jul 13 12:37:34 ma3x kernel: Switched to clocksource tsc
    Jul 13 12:37:34 ma3x kernel: random: nonblocking pool is initialized
    Jul 13 12:37:34 ma3x systemd[1]: Cannot add dependency job for unit display-manager.service, ignoring: Unit display-manager.service failed to load: No such file or directory.
    Jul 13 12:37:34 ma3x kernel: EXT4-fs (sda6): re-mounted. Opts: data=ordered
    Jul 13 12:37:34 ma3x systemd-journal[133]: Journal started
    Jul 13 12:37:34 ma3x systemd-udevd[152]: starting version 215
    Jul 13 12:37:35 ma3x kernel: shpchp: Standard Hot Plug PCI Controller Driver version: 0.4
    Jul 13 12:37:35 ma3x kernel: parport_pc 00:07: reported by Plug and Play ACPI
    Jul 13 12:37:35 ma3x kernel: parport0: PC-style at 0x378, irq 7 [PCSPP,TRISTATE]
    Jul 13 12:37:35 ma3x kernel: input: Power Button as /devices/LNXSYSTM:00/LNXSYBUS:00/PNP0C0C:00/input/input2
    Jul 13 12:37:35 ma3x kernel: ACPI: Power Button [PWRB]
    Jul 13 12:37:35 ma3x kernel: input: Power Button as /devices/LNXSYSTM:00/LNXPWRBN:00/input/input3
    Jul 13 12:37:35 ma3x kernel: ACPI: Power Button [PWRF]
    Jul 13 12:37:35 ma3x kernel: thermal LNXTHERM:00: registered as thermal_zone0
    Jul 13 12:37:35 ma3x kernel: ACPI: Thermal Zone [THRM] (23 C)
    Jul 13 12:37:35 ma3x kernel: ACPI: Fan [FAN] (on)
    Jul 13 12:37:35 ma3x kernel: ACPI Warning: SystemIO range 0x0000000000000428-0x000000000000042f conflicts with OpRegion 0x0000000000000429-0x0000000000000429 (\PM2S) (20140214/utaddress-258)
    Jul 13 12:37:35 ma3x kernel: ACPI: If an ACPI driver is available for this device, you should use it instead of the native driver
    Jul 13 12:37:35 ma3x kernel: ACPI Warning: SystemIO range 0x00000000000004b0-0x00000000000004bf conflicts with OpRegion 0x00000000000004b8-0x00000000000004bb (\GPO2) (20140214/utaddress-258)
    Jul 13 12:37:35 ma3x kernel: ACPI: If an ACPI driver is available for this device, you should use it instead of the native driver
    Jul 13 12:37:35 ma3x kernel: ACPI Warning: SystemIO range 0x0000000000000480-0x00000000000004af conflicts with OpRegion 0x000000000000048c-0x000000000000048f (\GPO_) (20140214/utaddress-258)
    Jul 13 12:37:35 ma3x kernel: ACPI: If an ACPI driver is available for this device, you should use it instead of the native driver
    Jul 13 12:37:35 ma3x kernel: lpc_ich: Resource conflict(s) found affecting gpio_ich
    Jul 13 12:37:35 ma3x kernel: i801_smbus 0000:00:1f.3: SMBus using PCI Interrupt
    Jul 13 12:37:35 ma3x kernel: r8169 Gigabit Ethernet driver 2.3LK-NAPI loaded
    Jul 13 12:37:35 ma3x kernel: r8169 0000:03:00.0: can't disable ASPM; OS doesn't have ASPM control
    Jul 13 12:37:35 ma3x kernel: r8169 0000:03:00.0: irq 44 for MSI/MSI-X
    Jul 13 12:37:35 ma3x kernel: r8169 0000:03:00.0 eth0: RTL8168b/8111b at 0xffffc90011468000, 00:30:18:ab:1c:1f, XID 98500000 IRQ 44
    Jul 13 12:37:35 ma3x kernel: r8169 0000:03:00.0 eth0: jumbo features [frames: 4080 bytes, tx checksumming: ko]
    Jul 13 12:37:35 ma3x kernel: microcode: CPU0 sig=0x1067a, pf=0x1, revision=0x0
    Jul 13 12:37:35 ma3x kernel: mousedev: PS/2 mouse device common for all mice
    Jul 13 12:37:35 ma3x kernel: ppdev: user-space parallel port driver
    Jul 13 12:37:35 ma3x kernel: [drm] Initialized drm 1.1.0 20060810
    Jul 13 12:37:35 ma3x kernel: iTCO_vendor_support: vendor-support=0
    Jul 13 12:37:35 ma3x kernel: iTCO_wdt: Intel TCO WatchDog Timer Driver v1.11
    Jul 13 12:37:35 ma3x kernel: iTCO_wdt: Found a ICH9 TCO device (Version=2, TCOBASE=0x0460)
    Jul 13 12:37:35 ma3x kernel: iTCO_wdt: initialized. heartbeat=30 sec (nowayout=0)
    Jul 13 12:37:35 ma3x kernel: 8139cp: 8139cp: 10/100 PCI Ethernet driver v1.3 (Mar 22, 2004)
    Jul 13 12:37:35 ma3x kernel: 8139cp 0000:05:00.0: This (id 10ec:8139 rev 10) is not an 8139C+ compatible chip, use 8139too
    Jul 13 12:37:35 ma3x kernel: [drm] radeon kernel modesetting enabled.
    Jul 13 12:37:35 ma3x kernel: checking generic (d0000000 500000) vs hw (d0000000 10000000)
    Jul 13 12:37:35 ma3x kernel: fb: switching to radeondrmfb from VESA VGA
    Jul 13 12:37:35 ma3x kernel: Console: switching to colour dummy device 80x25
    Jul 13 12:37:35 ma3x kernel: [drm] initializing kernel modesetting (JUNIPER 0x1002:0x68B8 0x1002:0x2543).
    Jul 13 12:37:35 ma3x kernel: [drm] register mmio base: 0xFDAC0000
    Jul 13 12:37:35 ma3x kernel: [drm] register mmio size: 131072
    Jul 13 12:37:35 ma3x kernel: ATOM BIOS: JUNIPER
    Jul 13 12:37:35 ma3x kernel: radeon 0000:01:00.0: VRAM: 1024M 0x0000000000000000 - 0x000000003FFFFFFF (1024M used)
    Jul 13 12:37:35 ma3x kernel: radeon 0000:01:00.0: GTT: 1024M 0x0000000040000000 - 0x000000007FFFFFFF
    Jul 13 12:37:35 ma3x kernel: [drm] Detected VRAM RAM=1024M, BAR=256M
    Jul 13 12:37:35 ma3x kernel: [drm] RAM width 128bits DDR
    Jul 13 12:37:35 ma3x kernel: [TTM] Zone kernel: Available graphics memory: 2025466 kiB
    Jul 13 12:37:35 ma3x kernel: [TTM] Initializing pool allocator
    Jul 13 12:37:35 ma3x kernel: [TTM] Initializing DMA pool allocator
    Jul 13 12:37:35 ma3x kernel: [drm] radeon: 1024M of VRAM memory ready
    Jul 13 12:37:35 ma3x kernel: [drm] radeon: 1024M of GTT memory ready.
    Jul 13 12:37:35 ma3x kernel: [drm] Loading JUNIPER Microcode
    Jul 13 12:37:36 ma3x systemd-udevd[164]: renamed network interface eth0 to enp3s0
    Jul 13 12:37:36 ma3x kernel: microcode: CPU1 sig=0x1067a, pf=0x1, revision=0x0
    Jul 13 12:37:36 ma3x kernel: microcode: Microcode Update Driver: v2.00 <[email protected]>, Peter Oruba
    Jul 13 12:37:36 ma3x kernel: 8139too: 8139too Fast Ethernet driver 0.9.28
    Jul 13 12:37:36 ma3x kernel: snd_hda_intel 0000:00:1b.0: irq 45 for MSI/MSI-X
    Jul 13 12:37:36 ma3x kernel: 8139too 0000:05:00.0 eth0: RealTek RTL8139 at 0xffffc900117f2000, 00:a0:d2:13:48:7d, IRQ 21
    Jul 13 12:37:36 ma3x systemd-udevd[162]: renamed network interface eth0 to enp5s0
    Jul 13 12:37:36 ma3x kernel: sound hdaudioC0D2: ignore pin 0x1b with mismatching assoc# 0x2 vs 0x1
    Jul 13 12:37:36 ma3x kernel: sound hdaudioC0D2: autoconfig: line_outs=4 (0x14/0x15/0x16/0x17/0x0) type:line
    Jul 13 12:37:36 ma3x kernel: sound hdaudioC0D2: speaker_outs=0 (0x0/0x0/0x0/0x0/0x0)
    Jul 13 12:37:36 ma3x kernel: sound hdaudioC0D2: hp_outs=0 (0x0/0x0/0x0/0x0/0x0)
    Jul 13 12:37:36 ma3x kernel: sound hdaudioC0D2: mono: mono_out=0x0
    Jul 13 12:37:36 ma3x kernel: sound hdaudioC0D2: dig-out=0x1e/0x0
    Jul 13 12:37:36 ma3x kernel: sound hdaudioC0D2: inputs:
    Jul 13 12:37:36 ma3x kernel: sound hdaudioC0D2: Front Mic=0x19
    Jul 13 12:37:36 ma3x kernel: sound hdaudioC0D2: Rear Mic=0x18
    Jul 13 12:37:36 ma3x kernel: sound hdaudioC0D2: Line=0x1a
    Jul 13 12:37:36 ma3x kernel: sound hdaudioC0D2: dig-in=0x1f
    Jul 13 12:37:36 ma3x kernel: input: HDA Intel Front Mic as /devices/pci0000:00/0000:00:1b.0/sound/card0/input4
    Jul 13 12:37:36 ma3x kernel: input: HDA Intel Rear Mic as /devices/pci0000:00/0000:00:1b.0/sound/card0/input5
    Jul 13 12:37:36 ma3x kernel: input: HDA Intel Line as /devices/pci0000:00/0000:00:1b.0/sound/card0/input6
    Jul 13 12:37:36 ma3x kernel: input: HDA Intel Line Out Front as /devices/pci0000:00/0000:00:1b.0/sound/card0/input7
    Jul 13 12:37:36 ma3x kernel: input: HDA Intel Line Out Surround as /devices/pci0000:00/0000:00:1b.0/sound/card0/input8
    Jul 13 12:37:36 ma3x kernel: input: HDA Intel Line Out CLFE as /devices/pci0000:00/0000:00:1b.0/sound/card0/input9
    Jul 13 12:37:36 ma3x kernel: input: HDA Intel Line Out Side as /devices/pci0000:00/0000:00:1b.0/sound/card0/input10
    Jul 13 12:37:37 ma3x kernel: Adding 4000148k swap on /dev/sda8. Priority:-1 extents:1 across:4000148k FS
    Jul 13 12:37:37 ma3x kernel: [drm] Internal thermal controller with fan control
    Jul 13 12:37:37 ma3x kernel: [drm] radeon: dpm initialized
    Jul 13 12:37:37 ma3x systemd-fsck[177]: /dev/sda7: clean, 36140/11976704 files, 3922434/47884345 blocks
    Jul 13 12:37:37 ma3x kernel: [drm] GART: num cpu pages 262144, num gpu pages 262144
    Jul 13 12:37:37 ma3x kernel: [drm] PCIE GART of 1024M enabled (table at 0x000000000025D000).
    Jul 13 12:37:37 ma3x kernel: radeon 0000:01:00.0: WB enabled
    Jul 13 12:37:37 ma3x kernel: radeon 0000:01:00.0: fence driver on ring 0 use gpu addr 0x0000000040000c00 and cpu addr 0xffff8801290c1c00
    Jul 13 12:37:37 ma3x kernel: radeon 0000:01:00.0: fence driver on ring 3 use gpu addr 0x0000000040000c0c and cpu addr 0xffff8801290c1c0c
    Jul 13 12:37:37 ma3x kernel: radeon 0000:01:00.0: fence driver on ring 5 use gpu addr 0x000000000005c418 and cpu addr 0xffffc9001309c418
    Jul 13 12:37:37 ma3x kernel: [drm] Supports vblank timestamp caching Rev 2 (21.10.2013).
    Jul 13 12:37:37 ma3x kernel: [drm] Driver supports precise vblank timestamp query.
    Jul 13 12:37:37 ma3x kernel: radeon 0000:01:00.0: irq 46 for MSI/MSI-X
    Jul 13 12:37:37 ma3x kernel: radeon 0000:01:00.0: radeon: using MSI.
    Jul 13 12:37:37 ma3x kernel: [drm] radeon: irq initialized.
    Jul 13 12:37:37 ma3x kernel: [drm] ring test on 0 succeeded in 1 usecs
    Jul 13 12:37:37 ma3x kernel: [drm] ring test on 3 succeeded in 1 usecs
    Jul 13 12:37:37 ma3x kernel: EXT4-fs (sda7): mounted filesystem with ordered data mode. Opts: data=ordered
    Jul 13 12:37:37 ma3x kernel: [drm] ring test on 5 succeeded in 1 usecs
    Jul 13 12:37:37 ma3x kernel: [drm] UVD initialized successfully.
    Jul 13 12:37:37 ma3x kernel: [drm] ib test on ring 0 succeeded in 0 usecs
    Jul 13 12:37:37 ma3x kernel: [drm] ib test on ring 3 succeeded in 0 usecs
    Jul 13 12:37:37 ma3x systemd-journal[133]: Permanent journal is using 40.0M (max allowed 2.0G, trying to leave 3.0G free of 12.3G available → current limit 2.0G).
    Jul 13 12:37:38 ma3x systemd-journal[133]: Time spent on flushing to /var is 734.588ms for 755 entries.
    Jul 13 12:37:39 ma3x kernel: [drm] ib test on ring 5 succeeded
    Jul 13 12:37:39 ma3x kernel: [drm] Radeon Display Connectors
    Jul 13 12:37:39 ma3x kernel: [drm] Connector 0:
    Jul 13 12:37:39 ma3x kernel: [drm] DP-1
    Jul 13 12:37:39 ma3x kernel: [drm] HPD4
    Jul 13 12:37:39 ma3x kernel: [drm] DDC: 0x6440 0x6440 0x6444 0x6444 0x6448 0x6448 0x644c 0x644c
    Jul 13 12:37:39 ma3x ker

    The first part of your mcelog (the bit about " failed to prefill DIMM database from DMI data") strongly suggest one of the new RAM chips is defective. Start by simply putting the old one back in place and seeing if that helps. If it does, exchange the new faulty one with the seller for one that works. However, since you say yourself you aren't very tech savvy, it may be the case that you've simply purchased a RAM chip that is not compatible with your motherboard (although if both of the new chips are identical and the first one works, that may not be so).
    When deciding to upgrade all the most vital hardware components of a machine, it's best to do it one piece at a time, and reconfigure the operating system to account for the new hardware. Uninstall old drivers, install new ones, change any personal settings related to the old hardware, reboot, make sure everything's fine and then repeat the process for every other new piece of hardware. Replacing everything at once without ensuring it will all work together increases the chances problems like this immensely---the problem itself may be very simple, but you've undertaken so many changes in such a short time that finding out what the problem is in the first place can be very complicated.

  • Need help debugging desktop crashes

    Hi all,
    I've started having trouble with random desktop crashes. It only happens occasionally (twice in the past couple of weeks), but my screens black out (no signal). The desktop is still powered on, but I can't ssh to it. I'm pretty sure I wasn't doing anything specific either time to cause the crash.
    Unfortunately, I don't have much more information (sorry!). I've been told on the IRC to look at dmesg, the output of which I've pasted below, but I can't really make head nor tail of it.
    Ask me and I'll post any other logs/command output that might help.
    dmesg:
    [ 0.000000] Initializing cgroup subsys cpuset
    [ 0.000000] Initializing cgroup subsys cpu
    [ 0.000000] Initializing cgroup subsys cpuacct
    [ 0.000000] Linux version 3.15.8-1-ARCH (nobody@var-lib-archbuild-testing-x86_64-tobias) (gcc version 4.9.1 (GCC) ) #1 SMP PREEMPT Fri Aug 1 08:51:42 CEST 2014
    [ 0.000000] Command line: BOOT_IMAGE=/vmlinuz-linux root=UUID=8fc8d7e8-be76-4428-a102-f74fbb580922 rw quiet
    [ 0.000000] e820: BIOS-provided physical RAM map:
    [ 0.000000] BIOS-e820: [mem 0x0000000000000000-0x000000000009ebff] usable
    [ 0.000000] BIOS-e820: [mem 0x000000000009ec00-0x000000000009ffff] reserved
    [ 0.000000] BIOS-e820: [mem 0x00000000000e0000-0x00000000000fffff] reserved
    [ 0.000000] BIOS-e820: [mem 0x0000000000100000-0x000000001fffffff] usable
    [ 0.000000] BIOS-e820: [mem 0x0000000020000000-0x00000000201fffff] reserved
    [ 0.000000] BIOS-e820: [mem 0x0000000020200000-0x0000000040003fff] usable
    [ 0.000000] BIOS-e820: [mem 0x0000000040004000-0x0000000040004fff] reserved
    [ 0.000000] BIOS-e820: [mem 0x0000000040005000-0x00000000c8fcefff] usable
    [ 0.000000] BIOS-e820: [mem 0x00000000c8fcf000-0x00000000c95d1fff] reserved
    [ 0.000000] BIOS-e820: [mem 0x00000000c95d2000-0x00000000c9825fff] ACPI NVS
    [ 0.000000] BIOS-e820: [mem 0x00000000c9826000-0x00000000c9832fff] ACPI data
    [ 0.000000] BIOS-e820: [mem 0x00000000c9833000-0x00000000c9851fff] ACPI NVS
    [ 0.000000] BIOS-e820: [mem 0x00000000c9852000-0x00000000c9856fff] ACPI data
    [ 0.000000] BIOS-e820: [mem 0x00000000c9857000-0x00000000c9899fff] ACPI NVS
    [ 0.000000] BIOS-e820: [mem 0x00000000c989a000-0x00000000c9ca9fff] usable
    [ 0.000000] BIOS-e820: [mem 0x00000000c9caa000-0x00000000c9ff3fff] reserved
    [ 0.000000] BIOS-e820: [mem 0x00000000c9ff4000-0x00000000c9ffffff] usable
    [ 0.000000] BIOS-e820: [mem 0x00000000cb000000-0x00000000cf1fffff] reserved
    [ 0.000000] BIOS-e820: [mem 0x00000000f8000000-0x00000000fbffffff] reserved
    [ 0.000000] BIOS-e820: [mem 0x00000000fec00000-0x00000000fec00fff] reserved
    [ 0.000000] BIOS-e820: [mem 0x00000000fed00000-0x00000000fed03fff] reserved
    [ 0.000000] BIOS-e820: [mem 0x00000000fed1c000-0x00000000fed1ffff] reserved
    [ 0.000000] BIOS-e820: [mem 0x00000000fee00000-0x00000000fee00fff] reserved
    [ 0.000000] BIOS-e820: [mem 0x00000000ff000000-0x00000000ffffffff] reserved
    [ 0.000000] BIOS-e820: [mem 0x0000000100000000-0x000000022fdfffff] usable
    [ 0.000000] NX (Execute Disable) protection: active
    [ 0.000000] SMBIOS 2.7 present.
    [ 0.000000] DMI: System manufacturer System Product Name/P8H77-V, BIOS 0324 02/15/2012
    [ 0.000000] e820: update [mem 0x00000000-0x00000fff] usable ==> reserved
    [ 0.000000] e820: remove [mem 0x000a0000-0x000fffff] usable
    [ 0.000000] No AGP bridge found
    [ 0.000000] e820: last_pfn = 0x22fe00 max_arch_pfn = 0x400000000
    [ 0.000000] MTRR default type: uncachable
    [ 0.000000] MTRR fixed ranges enabled:
    [ 0.000000] 00000-9FFFF write-back
    [ 0.000000] A0000-BFFFF uncachable
    [ 0.000000] C0000-CFFFF write-protect
    [ 0.000000] D0000-E7FFF uncachable
    [ 0.000000] E8000-FFFFF write-protect
    [ 0.000000] MTRR variable ranges enabled:
    [ 0.000000] 0 base 000000000 mask E00000000 write-back
    [ 0.000000] 1 base 200000000 mask FE0000000 write-back
    [ 0.000000] 2 base 220000000 mask FF0000000 write-back
    [ 0.000000] 3 base 0E0000000 mask FE0000000 uncachable
    [ 0.000000] 4 base 0D0000000 mask FF0000000 uncachable
    [ 0.000000] 5 base 0CC000000 mask FFC000000 uncachable
    [ 0.000000] 6 base 0CB000000 mask FFF000000 uncachable
    [ 0.000000] 7 base 22FE00000 mask FFFE00000 uncachable
    [ 0.000000] 8 disabled
    [ 0.000000] 9 disabled
    [ 0.000000] x86 PAT enabled: cpu 0, old 0x7040600070406, new 0x7010600070106
    [ 0.000000] e820: update [mem 0xcb000000-0xffffffff] usable ==> reserved
    [ 0.000000] e820: last_pfn = 0xca000 max_arch_pfn = 0x400000000
    [ 0.000000] found SMP MP-table at [mem 0x000fccf0-0x000fccff] mapped at [ffff8800000fccf0]
    [ 0.000000] Scanning 1 areas for low memory corruption
    [ 0.000000] Base memory trampoline at [ffff880000098000] 98000 size 24576
    [ 0.000000] init_memory_mapping: [mem 0x00000000-0x000fffff]
    [ 0.000000] [mem 0x00000000-0x000fffff] page 4k
    [ 0.000000] BRK [0x01b3e000, 0x01b3efff] PGTABLE
    [ 0.000000] BRK [0x01b3f000, 0x01b3ffff] PGTABLE
    [ 0.000000] BRK [0x01b40000, 0x01b40fff] PGTABLE
    [ 0.000000] init_memory_mapping: [mem 0x22fc00000-0x22fdfffff]
    [ 0.000000] [mem 0x22fc00000-0x22fdfffff] page 2M
    [ 0.000000] BRK [0x01b41000, 0x01b41fff] PGTABLE
    [ 0.000000] init_memory_mapping: [mem 0x22c000000-0x22fbfffff]
    [ 0.000000] [mem 0x22c000000-0x22fbfffff] page 2M
    [ 0.000000] init_memory_mapping: [mem 0x200000000-0x22bffffff]
    [ 0.000000] [mem 0x200000000-0x22bffffff] page 2M
    [ 0.000000] init_memory_mapping: [mem 0x00100000-0x1fffffff]
    [ 0.000000] [mem 0x00100000-0x001fffff] page 4k
    [ 0.000000] [mem 0x00200000-0x1fffffff] page 2M
    [ 0.000000] init_memory_mapping: [mem 0x20200000-0x40003fff]
    [ 0.000000] [mem 0x20200000-0x3fffffff] page 2M
    [ 0.000000] [mem 0x40000000-0x40003fff] page 4k
    [ 0.000000] BRK [0x01b42000, 0x01b42fff] PGTABLE
    [ 0.000000] BRK [0x01b43000, 0x01b43fff] PGTABLE
    [ 0.000000] init_memory_mapping: [mem 0x40005000-0xc8fcefff]
    [ 0.000000] [mem 0x40005000-0x401fffff] page 4k
    [ 0.000000] [mem 0x40200000-0xc8dfffff] page 2M
    [ 0.000000] [mem 0xc8e00000-0xc8fcefff] page 4k
    [ 0.000000] init_memory_mapping: [mem 0xc989a000-0xc9ca9fff]
    [ 0.000000] [mem 0xc989a000-0xc99fffff] page 4k
    [ 0.000000] [mem 0xc9a00000-0xc9bfffff] page 2M
    [ 0.000000] [mem 0xc9c00000-0xc9ca9fff] page 4k
    [ 0.000000] init_memory_mapping: [mem 0xc9ff4000-0xc9ffffff]
    [ 0.000000] [mem 0xc9ff4000-0xc9ffffff] page 4k
    [ 0.000000] init_memory_mapping: [mem 0x100000000-0x1ffffffff]
    [ 0.000000] [mem 0x100000000-0x1ffffffff] page 2M
    [ 0.000000] RAMDISK: [mem 0x37772000-0x37bb0fff]
    [ 0.000000] ACPI: RSDP 0x00000000000F0450 000024 (v02 ALASKA)
    [ 0.000000] ACPI: XSDT 0x00000000C9826078 00006C (v01 ALASKA A M I 01072009 AMI 00010013)
    [ 0.000000] ACPI: FACP 0x00000000C98308E0 0000F4 (v04 ALASKA A M I 01072009 AMI 00010013)
    [ 0.000000] ACPI: DSDT 0x00000000C9826170 00A76A (v02 ALASKA A M I 00000015 INTL 20051117)
    [ 0.000000] ACPI: FACS 0x00000000C9850F80 000040
    [ 0.000000] ACPI: APIC 0x00000000C98309D8 000072 (v03 ALASKA A M I 01072009 AMI 00010013)
    [ 0.000000] ACPI: MCFG 0x00000000C9830A50 00003C (v01 ALASKA A M I 01072009 MSFT 00000097)
    [ 0.000000] ACPI: HPET 0x00000000C9830A90 000038 (v01 ALASKA A M I 01072009 AMI. 00000005)
    [ 0.000000] ACPI: SSDT 0x00000000C9830AC8 000460 (v01 IdeRef IdeTable 00001000 INTL 20091112)
    [ 0.000000] ACPI: SSDT 0x00000000C9830F28 0009AA (v01 PmRef Cpu0Ist 00003000 INTL 20051117)
    [ 0.000000] ACPI: SSDT 0x00000000C98318D8 000A92 (v01 PmRef CpuPm 00003000 INTL 20051117)
    [ 0.000000] ACPI: DMAR 0x00000000C9832370 0000B8 (v01 INTEL SNB 00000001 INTL 00000001)
    [ 0.000000] ACPI: BGRT 0x00000000C9832428 000038 (v00 ALASKA A M I 01072009 AMI 00010013)
    [ 0.000000] ACPI: Local APIC address 0xfee00000
    [ 0.000000] No NUMA configuration found
    [ 0.000000] Faking a node at [mem 0x0000000000000000-0x000000022fdfffff]
    [ 0.000000] Initmem setup node 0 [mem 0x00000000-0x22fdfffff]
    [ 0.000000] NODE_DATA [mem 0x22fdf1000-0x22fdf5fff]
    [ 0.000000] [ffffea0000000000-ffffea0008bfffff] PMD -> [ffff880227400000-ffff88022f3fffff] on node 0
    [ 0.000000] Zone ranges:
    [ 0.000000] DMA [mem 0x00001000-0x00ffffff]
    [ 0.000000] DMA32 [mem 0x01000000-0xffffffff]
    [ 0.000000] Normal [mem 0x100000000-0x22fdfffff]
    [ 0.000000] Movable zone start for each node
    [ 0.000000] Early memory node ranges
    [ 0.000000] node 0: [mem 0x00001000-0x0009dfff]
    [ 0.000000] node 0: [mem 0x00100000-0x1fffffff]
    [ 0.000000] node 0: [mem 0x20200000-0x40003fff]
    [ 0.000000] node 0: [mem 0x40005000-0xc8fcefff]
    [ 0.000000] node 0: [mem 0xc989a000-0xc9ca9fff]
    [ 0.000000] node 0: [mem 0xc9ff4000-0xc9ffffff]
    [ 0.000000] node 0: [mem 0x100000000-0x22fdfffff]
    [ 0.000000] On node 0 totalpages: 2068359
    [ 0.000000] DMA zone: 64 pages used for memmap
    [ 0.000000] DMA zone: 21 pages reserved
    [ 0.000000] DMA zone: 3997 pages, LIFO batch:0
    [ 0.000000] DMA32 zone: 12808 pages used for memmap
    [ 0.000000] DMA32 zone: 819690 pages, LIFO batch:31
    [ 0.000000] Normal zone: 19448 pages used for memmap
    [ 0.000000] Normal zone: 1244672 pages, LIFO batch:31
    [ 0.000000] ACPI: PM-Timer IO Port: 0x408
    [ 0.000000] ACPI: Local APIC address 0xfee00000
    [ 0.000000] ACPI: LAPIC (acpi_id[0x01] lapic_id[0x00] enabled)
    [ 0.000000] ACPI: LAPIC (acpi_id[0x02] lapic_id[0x02] enabled)
    [ 0.000000] ACPI: LAPIC (acpi_id[0x03] lapic_id[0x04] enabled)
    [ 0.000000] ACPI: LAPIC (acpi_id[0x04] lapic_id[0x06] enabled)
    [ 0.000000] ACPI: LAPIC_NMI (acpi_id[0xff] high edge lint[0x1])
    [ 0.000000] ACPI: IOAPIC (id[0x02] address[0xfec00000] gsi_base[0])
    [ 0.000000] IOAPIC[0]: apic_id 2, version 32, address 0xfec00000, GSI 0-23
    [ 0.000000] ACPI: INT_SRC_OVR (bus 0 bus_irq 0 global_irq 2 dfl dfl)
    [ 0.000000] ACPI: INT_SRC_OVR (bus 0 bus_irq 9 global_irq 9 high level)
    [ 0.000000] ACPI: IRQ0 used by override.
    [ 0.000000] ACPI: IRQ2 used by override.
    [ 0.000000] ACPI: IRQ9 used by override.
    [ 0.000000] Using ACPI (MADT) for SMP configuration information
    [ 0.000000] ACPI: HPET id: 0x8086a701 base: 0xfed00000
    [ 0.000000] smpboot: Allowing 4 CPUs, 0 hotplug CPUs
    [ 0.000000] nr_irqs_gsi: 40
    [ 0.000000] PM: Registered nosave memory: [mem 0x0009e000-0x0009efff]
    [ 0.000000] PM: Registered nosave memory: [mem 0x0009f000-0x0009ffff]
    [ 0.000000] PM: Registered nosave memory: [mem 0x000a0000-0x000dffff]
    [ 0.000000] PM: Registered nosave memory: [mem 0x000e0000-0x000fffff]
    [ 0.000000] PM: Registered nosave memory: [mem 0x20000000-0x201fffff]
    [ 0.000000] PM: Registered nosave memory: [mem 0x40004000-0x40004fff]
    [ 0.000000] PM: Registered nosave memory: [mem 0xc8fcf000-0xc95d1fff]
    [ 0.000000] PM: Registered nosave memory: [mem 0xc95d2000-0xc9825fff]
    [ 0.000000] PM: Registered nosave memory: [mem 0xc9826000-0xc9832fff]
    [ 0.000000] PM: Registered nosave memory: [mem 0xc9833000-0xc9851fff]
    [ 0.000000] PM: Registered nosave memory: [mem 0xc9852000-0xc9856fff]
    [ 0.000000] PM: Registered nosave memory: [mem 0xc9857000-0xc9899fff]
    [ 0.000000] PM: Registered nosave memory: [mem 0xc9caa000-0xc9ff3fff]
    [ 0.000000] PM: Registered nosave memory: [mem 0xca000000-0xcaffffff]
    [ 0.000000] PM: Registered nosave memory: [mem 0xcb000000-0xcf1fffff]
    [ 0.000000] PM: Registered nosave memory: [mem 0xcf200000-0xf7ffffff]
    [ 0.000000] PM: Registered nosave memory: [mem 0xf8000000-0xfbffffff]
    [ 0.000000] PM: Registered nosave memory: [mem 0xfc000000-0xfebfffff]
    [ 0.000000] PM: Registered nosave memory: [mem 0xfec00000-0xfec00fff]
    [ 0.000000] PM: Registered nosave memory: [mem 0xfec01000-0xfecfffff]
    [ 0.000000] PM: Registered nosave memory: [mem 0xfed00000-0xfed03fff]
    [ 0.000000] PM: Registered nosave memory: [mem 0xfed04000-0xfed1bfff]
    [ 0.000000] PM: Registered nosave memory: [mem 0xfed1c000-0xfed1ffff]
    [ 0.000000] PM: Registered nosave memory: [mem 0xfed20000-0xfedfffff]
    [ 0.000000] PM: Registered nosave memory: [mem 0xfee00000-0xfee00fff]
    [ 0.000000] PM: Registered nosave memory: [mem 0xfee01000-0xfeffffff]
    [ 0.000000] PM: Registered nosave memory: [mem 0xff000000-0xffffffff]
    [ 0.000000] e820: [mem 0xcf200000-0xf7ffffff] available for PCI devices
    [ 0.000000] Booting paravirtualized kernel on bare hardware
    [ 0.000000] setup_percpu: NR_CPUS:128 nr_cpumask_bits:128 nr_cpu_ids:4 nr_node_ids:1
    [ 0.000000] PERCPU: Embedded 29 pages/cpu @ffff88022fa00000 s87168 r8192 d23424 u524288
    [ 0.000000] pcpu-alloc: s87168 r8192 d23424 u524288 alloc=1*2097152
    [ 0.000000] pcpu-alloc: [0] 0 1 2 3
    [ 0.000000] Built 1 zonelists in Zone order, mobility grouping on. Total pages: 2036018
    [ 0.000000] Policy zone: Normal
    [ 0.000000] Kernel command line: BOOT_IMAGE=/vmlinuz-linux root=UUID=8fc8d7e8-be76-4428-a102-f74fbb580922 rw quiet
    [ 0.000000] PID hash table entries: 4096 (order: 3, 32768 bytes)
    [ 0.000000] xsave: enabled xstate_bv 0x7, cntxt size 0x340
    [ 0.000000] Checking aperture...
    [ 0.000000] No AGP bridge found
    [ 0.000000] Calgary: detecting Calgary via BIOS EBDA area
    [ 0.000000] Calgary: Unable to locate Rio Grande table in EBDA - bailing!
    [ 0.000000] Memory: 8059568K/8273436K available (5225K kernel code, 886K rwdata, 1644K rodata, 1116K init, 1284K bss, 213868K reserved)
    [ 0.000000] SLUB: HWalign=64, Order=0-3, MinObjects=0, CPUs=4, Nodes=1
    [ 0.000000] Preemptible hierarchical RCU implementation.
    [ 0.000000] RCU dyntick-idle grace-period acceleration is enabled.
    [ 0.000000] Dump stacks of tasks blocking RCU-preempt GP.
    [ 0.000000] RCU restricting CPUs from NR_CPUS=128 to nr_cpu_ids=4.
    [ 0.000000] RCU: Adjusting geometry for rcu_fanout_leaf=16, nr_cpu_ids=4
    [ 0.000000] NR_IRQS:8448 nr_irqs:712 16
    [ 0.000000] Console: colour dummy device 80x25
    [ 0.000000] console [tty0] enabled
    [ 0.000000] allocated 33554432 bytes of page_cgroup
    [ 0.000000] please try 'cgroup_disable=memory' option if you don't want memory cgroups
    [ 0.000000] hpet clockevent registered
    [ 0.000000] tsc: Fast TSC calibration using PIT
    [ 0.000000] tsc: Detected 3398.854 MHz processor
    [ 0.000026] Calibrating delay loop (skipped), value calculated using timer frequency.. 6800.94 BogoMIPS (lpj=11329513)
    [ 0.000028] pid_max: default: 32768 minimum: 301
    [ 0.000032] ACPI: Core revision 20140214
    [ 0.004609] ACPI: All ACPI Tables successfully acquired
    [ 0.006765] Security Framework initialized
    [ 0.006770] Yama: becoming mindful.
    [ 0.007110] Dentry cache hash table entries: 1048576 (order: 11, 8388608 bytes)
    [ 0.008539] Inode-cache hash table entries: 524288 (order: 10, 4194304 bytes)
    [ 0.009174] Mount-cache hash table entries: 16384 (order: 5, 131072 bytes)
    [ 0.009181] Mountpoint-cache hash table entries: 16384 (order: 5, 131072 bytes)
    [ 0.009321] Initializing cgroup subsys memory
    [ 0.009324] Initializing cgroup subsys devices
    [ 0.009326] Initializing cgroup subsys freezer
    [ 0.009327] Initializing cgroup subsys net_cls
    [ 0.009328] Initializing cgroup subsys blkio
    [ 0.009342] CPU: Physical Processor ID: 0
    [ 0.009343] CPU: Processor Core ID: 0
    [ 0.009346] ENERGY_PERF_BIAS: Set to 'normal', was 'performance'
    ENERGY_PERF_BIAS: View and update with x86_energy_perf_policy(8)
    [ 0.009609] mce: CPU supports 9 MCE banks
    [ 0.009618] CPU0: Thermal monitoring enabled (TM1)
    [ 0.009626] Last level iTLB entries: 4KB 512, 2MB 8, 4MB 8
    Last level dTLB entries: 4KB 512, 2MB 32, 4MB 32, 1GB 0
    tlb_flushall_shift: 2
    [ 0.009699] Freeing SMP alternatives memory: 20K (ffffffff819f6000 - ffffffff819fb000)
    [ 0.010378] ftrace: allocating 20229 entries in 80 pages
    [ 0.017451] dmar: Host address width 36
    [ 0.017453] dmar: DRHD base: 0x000000fed90000 flags: 0x0
    [ 0.017459] dmar: IOMMU 0: reg_base_addr fed90000 ver 1:0 cap c0000020e60262 ecap f0101a
    [ 0.017460] dmar: DRHD base: 0x000000fed91000 flags: 0x1
    [ 0.017464] dmar: IOMMU 1: reg_base_addr fed91000 ver 1:0 cap c9008020660262 ecap f0105a
    [ 0.017464] dmar: RMRR base: 0x000000c9549000 end: 0x000000c9565fff
    [ 0.017465] dmar: RMRR base: 0x000000cb000000 end: 0x000000cf1fffff
    [ 0.017533] IOAPIC id 2 under DRHD base 0xfed91000 IOMMU 1
    [ 0.017533] HPET id 0 under DRHD base 0xfed91000
    [ 0.017534] Queued invalidation will be enabled to support x2apic and Intr-remapping.
    [ 0.017639] Enabled IRQ remapping in x2apic mode
    [ 0.017640] Enabling x2apic
    [ 0.017640] Enabled x2apic
    [ 0.017644] Switched APIC routing to cluster x2apic.
    [ 0.018045] ..TIMER: vector=0x30 apic1=0 pin1=2 apic2=-1 pin2=-1
    [ 0.051017] smpboot: CPU0: Intel(R) Core(TM) i5-3550 CPU @ 3.30GHz (fam: 06, model: 3a, stepping: 09)
    [ 0.051022] TSC deadline timer enabled
    [ 0.051028] Performance Events: PEBS fmt1+, 16-deep LBR, IvyBridge events, full-width counters, Intel PMU driver.
    [ 0.051033] ... version: 3
    [ 0.051033] ... bit width: 48
    [ 0.051034] ... generic registers: 8
    [ 0.051035] ... value mask: 0000ffffffffffff
    [ 0.051035] ... max period: 0000ffffffffffff
    [ 0.051036] ... fixed-purpose events: 3
    [ 0.051036] ... event mask: 00000007000000ff
    [ 0.074413] x86: Booting SMP configuration:
    [ 0.074416] .... node #0, CPUs: #1
    [ 0.087877] NMI watchdog: enabled on all CPUs, permanently consumes one hw-PMU counter.
    [ 0.094547] #2 #3
    [ 0.128105] x86: Booted up 1 node, 4 CPUs
    [ 0.128108] smpboot: Total of 4 processors activated (27201.78 BogoMIPS)
    [ 0.130404] devtmpfs: initialized
    [ 0.132695] PM: Registering ACPI NVS region [mem 0xc95d2000-0xc9825fff] (2441216 bytes)
    [ 0.132717] PM: Registering ACPI NVS region [mem 0xc9833000-0xc9851fff] (126976 bytes)
    [ 0.132719] PM: Registering ACPI NVS region [mem 0xc9857000-0xc9899fff] (274432 bytes)
    [ 0.133240] pinctrl core: initialized pinctrl subsystem
    [ 0.133269] RTC time: 14:04:30, date: 08/05/14
    [ 0.133295] NET: Registered protocol family 16
    [ 0.133354] cpuidle: using governor ladder
    [ 0.133354] cpuidle: using governor menu
    [ 0.133363] ACPI FADT declares the system doesn't support PCIe ASPM, so disable it
    [ 0.133364] ACPI: bus type PCI registered
    [ 0.133365] acpiphp: ACPI Hot Plug PCI Controller Driver version: 0.5
    [ 0.133402] PCI: MMCONFIG for domain 0000 [bus 00-3f] at [mem 0xf8000000-0xfbffffff] (base 0xf8000000)
    [ 0.133404] PCI: MMCONFIG at [mem 0xf8000000-0xfbffffff] reserved in E820
    [ 0.133461] PCI: Using configuration type 1 for base access
    [ 0.134021] ACPI: Added _OSI(Module Device)
    [ 0.134022] ACPI: Added _OSI(Processor Device)
    [ 0.134023] ACPI: Added _OSI(3.0 _SCP Extensions)
    [ 0.134024] ACPI: Added _OSI(Processor Aggregator Device)
    [ 0.135968] ACPI: Executed 1 blocks of module-level executable AML code
    [ 0.148373] ACPI: SSDT 0x00000000C9583018 00083B (v01 PmRef Cpu0Cst 00003001 INTL 20051117)
    [ 0.148602] ACPI: Dynamic OEM Table Load:
    [ 0.148603] ACPI: SSDT 0x0000000000000000 00083B (v01 PmRef Cpu0Cst 00003001 INTL 20051117)
    [ 0.158263] ACPI: SSDT 0x00000000C9584A98 000303 (v01 PmRef ApIst 00003000 INTL 20051117)
    [ 0.158527] ACPI: Dynamic OEM Table Load:
    [ 0.158528] ACPI: SSDT 0x0000000000000000 000303 (v01 PmRef ApIst 00003000 INTL 20051117)
    [ 0.168175] ACPI: SSDT 0x00000000C9582D98 000119 (v01 PmRef ApCst 00003000 INTL 20051117)
    [ 0.168404] ACPI: Dynamic OEM Table Load:
    [ 0.168405] ACPI: SSDT 0x0000000000000000 000119 (v01 PmRef ApCst 00003000 INTL 20051117)
    [ 0.178489] ACPI: Interpreter enabled
    [ 0.178496] ACPI Exception: AE_NOT_FOUND, While evaluating Sleep State [\_S2_] (20140214/hwxface-580)
    [ 0.178504] ACPI: (supports S0 S1 S3 S4 S5)
    [ 0.178505] ACPI: Using IOAPIC for interrupt routing
    [ 0.178521] PCI: Using host bridge windows from ACPI; if necessary, use "pci=nocrs" and report a bug
    [ 0.182207] ACPI: Power Resource [FN00] (off)
    [ 0.182256] ACPI: Power Resource [FN01] (off)
    [ 0.182304] ACPI: Power Resource [FN02] (off)
    [ 0.182352] ACPI: Power Resource [FN03] (off)
    [ 0.182399] ACPI: Power Resource [FN04] (off)
    [ 0.182776] ACPI: PCI Root Bridge [PCI0] (domain 0000 [bus 00-3e])
    [ 0.182779] acpi PNP0A08:00: _OSC: OS supports [ExtendedConfig ASPM ClockPM Segments MSI]
    [ 0.182857] \_SB_.PCI0:_OSC invalid UUID
    [ 0.182858] _OSC request data:1 1f 0
    [ 0.182860] acpi PNP0A08:00: _OSC failed (AE_ERROR); disabling ASPM
    [ 0.183226] PCI host bridge to bus 0000:00
    [ 0.183228] pci_bus 0000:00: root bus resource [bus 00-3e]
    [ 0.183229] pci_bus 0000:00: root bus resource [io 0x0000-0x0cf7]
    [ 0.183230] pci_bus 0000:00: root bus resource [io 0x0d00-0xffff]
    [ 0.183232] pci_bus 0000:00: root bus resource [mem 0x000a0000-0x000bffff]
    [ 0.183233] pci_bus 0000:00: root bus resource [mem 0x000d0000-0x000d3fff]
    [ 0.183234] pci_bus 0000:00: root bus resource [mem 0x000d4000-0x000d7fff]
    [ 0.183235] pci_bus 0000:00: root bus resource [mem 0x000d8000-0x000dbfff]
    [ 0.183236] pci_bus 0000:00: root bus resource [mem 0x000dc000-0x000dffff]
    [ 0.183237] pci_bus 0000:00: root bus resource [mem 0x000e0000-0x000e3fff]
    [ 0.183238] pci_bus 0000:00: root bus resource [mem 0x000e4000-0x000e7fff]
    [ 0.183239] pci_bus 0000:00: root bus resource [mem 0xcf200000-0xfeafffff]
    [ 0.183244] pci 0000:00:00.0: [8086:0150] type 00 class 0x060000
    [ 0.183301] pci 0000:00:01.0: [8086:0151] type 01 class 0x060400
    [ 0.183326] pci 0000:00:01.0: PME# supported from D0 D3hot D3cold
    [ 0.183349] pci 0000:00:01.0: System wakeup disabled by ACPI
    [ 0.183377] pci 0000:00:02.0: [8086:0152] type 00 class 0x038000
    [ 0.183384] pci 0000:00:02.0: reg 0x10: [mem 0xf7800000-0xf7bfffff 64bit]
    [ 0.183389] pci 0000:00:02.0: reg 0x18: [mem 0xd0000000-0xdfffffff 64bit pref]
    [ 0.183392] pci 0000:00:02.0: reg 0x20: [io 0xf000-0xf03f]
    [ 0.183462] pci 0000:00:14.0: [8086:1e31] type 00 class 0x0c0330
    [ 0.183481] pci 0000:00:14.0: reg 0x10: [mem 0xf7e00000-0xf7e0ffff 64bit]
    [ 0.183546] pci 0000:00:14.0: PME# supported from D3hot D3cold
    [ 0.183572] pci 0000:00:14.0: System wakeup disabled by ACPI
    [ 0.183601] pci 0000:00:16.0: [8086:1e3a] type 00 class 0x078000
    [ 0.183621] pci 0000:00:16.0: reg 0x10: [mem 0xf7e19000-0xf7e1900f 64bit]
    [ 0.183689] pci 0000:00:16.0: PME# supported from D0 D3hot D3cold
    [ 0.183750] pci 0000:00:1a.0: [8086:1e2d] type 00 class 0x0c0320
    [ 0.183768] pci 0000:00:1a.0: reg 0x10: [mem 0xf7e17000-0xf7e173ff]
    [ 0.183850] pci 0000:00:1a.0: PME# supported from D0 D3hot D3cold
    [ 0.183888] pci 0000:00:1a.0: System wakeup disabled by ACPI
    [ 0.183917] pci 0000:00:1b.0: [8086:1e20] type 00 class 0x040300
    [ 0.183930] pci 0000:00:1b.0: reg 0x10: [mem 0xf7e10000-0xf7e13fff 64bit]
    [ 0.183996] pci 0000:00:1b.0: PME# supported from D0 D3hot D3cold
    [ 0.184024] pci 0000:00:1b.0: System wakeup disabled by ACPI
    [ 0.184050] pci 0000:00:1c.0: [8086:1e10] type 01 class 0x060400
    [ 0.184123] pci 0000:00:1c.0: PME# supported from D0 D3hot D3cold
    [ 0.184153] pci 0000:00:1c.0: System wakeup disabled by ACPI
    [ 0.184182] pci 0000:00:1c.4: [8086:1e18] type 01 class 0x060400
    [ 0.184254] pci 0000:00:1c.4: PME# supported from D0 D3hot D3cold
    [ 0.184285] pci 0000:00:1c.4: System wakeup disabled by ACPI
    [ 0.184311] pci 0000:00:1c.5: [8086:244e] type 01 class 0x060401
    [ 0.184383] pci 0000:00:1c.5: PME# supported from D0 D3hot D3cold
    [ 0.184414] pci 0000:00:1c.5: System wakeup disabled by ACPI
    [ 0.184445] pci 0000:00:1d.0: [8086:1e26] type 00 class 0x0c0320
    [ 0.184463] pci 0000:00:1d.0: reg 0x10: [mem 0xf7e16000-0xf7e163ff]
    [ 0.184545] pci 0000:00:1d.0: PME# supported from D0 D3hot D3cold
    [ 0.184580] pci 0000:00:1d.0: System wakeup disabled by ACPI
    [ 0.184609] pci 0000:00:1f.0: [8086:1e4a] type 00 class 0x060100
    [ 0.184751] pci 0000:00:1f.2: [8086:1e00] type 00 class 0x01018f
    [ 0.184764] pci 0000:00:1f.2: reg 0x10: [io 0xf110-0xf117]
    [ 0.184770] pci 0000:00:1f.2: reg 0x14: [io 0xf100-0xf103]
    [ 0.184776] pci 0000:00:1f.2: reg 0x18: [io 0xf0f0-0xf0f7]
    [ 0.184783] pci 0000:00:1f.2: reg 0x1c: [io 0xf0e0-0xf0e3]
    [ 0.184789] pci 0000:00:1f.2: reg 0x20: [io 0xf0d0-0xf0df]
    [ 0.184795] pci 0000:00:1f.2: reg 0x24: [io 0xf0c0-0xf0cf]
    [ 0.184863] pci 0000:00:1f.3: [8086:1e22] type 00 class 0x0c0500
    [ 0.184876] pci 0000:00:1f.3: reg 0x10: [mem 0xf7e15000-0xf7e150ff 64bit]
    [ 0.184895] pci 0000:00:1f.3: reg 0x20: [io 0xf040-0xf05f]
    [ 0.184952] pci 0000:00:1f.5: [8086:1e08] type 00 class 0x010185
    [ 0.184965] pci 0000:00:1f.5: reg 0x10: [io 0xf0b0-0xf0b7]
    [ 0.184971] pci 0000:00:1f.5: reg 0x14: [io 0xf0a0-0xf0a3]
    [ 0.184977] pci 0000:00:1f.5: reg 0x18: [io 0xf090-0xf097]
    [ 0.184983] pci 0000:00:1f.5: reg 0x1c: [io 0xf080-0xf083]
    [ 0.184990] pci 0000:00:1f.5: reg 0x20: [io 0xf070-0xf07f]
    [ 0.184996] pci 0000:00:1f.5: reg 0x24: [io 0xf060-0xf06f]
    [ 0.185091] pci 0000:01:00.0: [1002:683d] type 00 class 0x030000
    [ 0.185098] pci 0000:01:00.0: reg 0x10: [mem 0xe0000000-0xefffffff 64bit pref]
    [ 0.185103] pci 0000:01:00.0: reg 0x18: [mem 0xf7d00000-0xf7d3ffff 64bit]
    [ 0.185107] pci 0000:01:00.0: reg 0x20: [io 0xe000-0xe0ff]
    [ 0.185114] pci 0000:01:00.0: reg 0x30: [mem 0xf7d40000-0xf7d5ffff pref]
    [ 0.185135] pci 0000:01:00.0: supports D1 D2
    [ 0.185136] pci 0000:01:00.0: PME# supported from D1 D2 D3hot
    [ 0.185168] pci 0000:01:00.1: [1002:aab0] type 00 class 0x040300
    [ 0.185175] pci 0000:01:00.1: reg 0x10: [mem 0xf7d60000-0xf7d63fff 64bit]
    [ 0.185208] pci 0000:01:00.1: supports D1 D2
    [ 0.191417] pci 0000:00:01.0: PCI bridge to [bus 01]
    [ 0.191421] pci 0000:00:01.0: bridge window [io 0xe000-0xefff]
    [ 0.191424] pci 0000:00:01.0: bridge window [mem 0xf7d00000-0xf7dfffff]
    [ 0.191429] pci 0000:00:01.0: bridge window [mem 0xe0000000-0xefffffff 64bit pref]
    [ 0.191505] pci 0000:00:1c.0: PCI bridge to [bus 02]
    [ 0.191582] pci 0000:03:00.0: [1969:1091] type 00 class 0x020000
    [ 0.191608] pci 0000:03:00.0: reg 0x10: [mem 0xf7c00000-0xf7c3ffff 64bit]
    [ 0.191621] pci 0000:03:00.0: reg 0x18: [io 0xd000-0xd07f]
    [ 0.191754] pci 0000:03:00.0: PME# supported from D0 D1 D2 D3hot D3cold
    [ 0.191784] pci 0000:03:00.0: System wakeup disabled by ACPI
    [ 0.198088] pci 0000:00:1c.4: PCI bridge to [bus 03]
    [ 0.198092] pci 0000:00:1c.4: bridge window [io 0xd000-0xdfff]
    [ 0.198097] pci 0000:00:1c.4: bridge window [mem 0xf7c00000-0xf7cfffff]
    [ 0.198192] pci 0000:04:00.0: [1b21:1080] type 01 class 0x060401
    [ 0.198307] pci 0000:04:00.0: System wakeup disabled by ACPI
    [ 0.198328] pci 0000:00:1c.5: PCI bridge to [bus 04-05] (subtractive decode)
    [ 0.198337] pci 0000:00:1c.5: bridge window [io 0x0000-0x0cf7] (subtractive decode)
    [ 0.198338] pci 0000:00:1c.5: bridge window [io 0x0d00-0xffff] (subtractive decode)
    [ 0.198339] pci 0000:00:1c.5: bridge window [mem 0x000a0000-0x000bffff] (subtractive decode)
    [ 0.198340] pci 0000:00:1c.5: bridge window [mem 0x000d0000-0x000d3fff] (subtractive decode)
    [ 0.198341] pci 0000:00:1c.5: bridge window [mem 0x000d4000-0x000d7fff] (subtractive decode)
    [ 0.198342] pci 0000:00:1c.5: bridge window [mem 0x000d8000-0x000dbfff] (subtractive decode)
    [ 0.198344] pci 0000:00:1c.5: bridge window [mem 0x000dc000-0x000dffff] (subtractive decode)
    [ 0.198345] pci 0000:00:1c.5: bridge window [mem 0x000e0000-0x000e3fff] (subtractive decode)
    [ 0.198346] pci 0000:00:1c.5: bridge window [mem 0x000e4000-0x000e7fff] (subtractive decode)
    [ 0.198347] pci 0000:00:1c.5: bridge window [mem 0xcf200000-0xfeafffff] (subtractive decode)
    [ 0.198457] pci 0000:04:00.0: PCI bridge to [bus 05] (subtractive decode)
    [ 0.198477] pci 0000:04:00.0: bridge window [??? 0x00000000 flags 0x0] (subtractive decode)
    [ 0.198478] pci 0000:04:00.0: bridge window [??? 0x00000000 flags 0x0] (subtractive decode)
    [ 0.198479] pci 0000:04:00.0: bridge window [??? 0x00000000 flags 0x0] (subtractive decode)
    [ 0.198480] pci 0000:04:00.0: bridge window [??? 0x00000000 flags 0x0] (subtractive decode)
    [ 0.198481] pci 0000:04:00.0: bridge window [io 0x0000-0x0cf7] (subtractive decode)
    [ 0.198482] pci 0000:04:00.0: bridge window [io 0x0d00-0xffff] (subtractive decode)
    [ 0.198483] pci 0000:04:00.0: bridge window [mem 0x000a0000-0x000bffff] (subtractive decode)
    [ 0.198484] pci 0000:04:00.0: bridge window [mem 0x000d0000-0x000d3fff] (subtractive decode)
    [ 0.198486] pci 0000:04:00.0: bridge window [mem 0x000d4000-0x000d7fff] (subtractive decode)
    [ 0.198487] pci 0000:04:00.0: bridge window [mem 0x000d8000-0x000dbfff] (subtractive decode)
    [ 0.198488] pci 0000:04:00.0: bridge window [mem 0x000dc000-0x000dffff] (subtractive decode)
    [ 0.198489] pci 0000:04:00.0: bridge window [mem 0x000e0000-0x000e3fff] (subtractive decode)
    [ 0.198490] pci 0000:04:00.0: bridge window [mem 0x000e4000-0x000e7fff] (subtractive decode)
    [ 0.198491] pci 0000:04:00.0: bridge window [mem 0xcf200000-0xfeafffff] (subtractive decode)
    [ 0.198687] ACPI: PCI Interrupt Link [LNKA] (IRQs 3 4 5 6 10 *11 12 14 15)
    [ 0.198720] ACPI: PCI Interrupt Link [LNKB] (IRQs 3 4 5 6 *10 11 12 14 15)
    [ 0.198751] ACPI: PCI Interrupt Link [LNKC] (IRQs 3 4 *5 6 10 11 12 14 15)
    [ 0.198781] ACPI: PCI Interrupt Link [LNKD] (IRQs *3 4 5 6 10 11 12 14 15)
    [ 0.198813] ACPI: PCI Interrupt Link [LNKE] (IRQs 3 4 5 6 10 11 12 14 15) *0, disabled.
    [ 0.198844] ACPI: PCI Interrupt Link [LNKF] (IRQs 3 4 *5 6 10 11 12 14 15)
    [ 0.198875] ACPI: PCI Interrupt Link [LNKG] (IRQs 3 4 5 6 *10 11 12 14 15)
    [ 0.198905] ACPI: PCI Interrupt Link [LNKH] (IRQs 3 4 5 6 10 *11 12 14 15)
    [ 0.198977] ACPI: Enabled 4 GPEs in block 00 to 3F
    [ 0.199032] vgaarb: device added: PCI:0000:01:00.0,decodes=io+mem,owns=io+mem,locks=none
    [ 0.199034] vgaarb: loaded
    [ 0.199034] vgaarb: bridge control possible 0000:01:00.0
    [ 0.199048] PCI: Using ACPI for IRQ routing
    [ 0.200393] PCI: pci_cache_line_size set to 64 bytes
    [ 0.200434] e820: reserve RAM buffer [mem 0x0009ec00-0x0009ffff]
    [ 0.200435] e820: reserve RAM buffer [mem 0x40004000-0x43ffffff]
    [ 0.200436] e820: reserve RAM buffer [mem 0xc8fcf000-0xcbffffff]
    [ 0.200437] e820: reserve RAM buffer [mem 0xc9caa000-0xcbffffff]
    [ 0.200438] e820: reserve RAM buffer [mem 0xca000000-0xcbffffff]
    [ 0.200439] e820: reserve RAM buffer [mem 0x22fe00000-0x22fffffff]
    [ 0.200497] NetLabel: Initializing
    [ 0.200497] NetLabel: domain hash size = 128
    [ 0.200498] NetLabel: protocols = UNLABELED CIPSOv4
    [ 0.200505] NetLabel: unlabeled traffic allowed by default
    [ 0.200518] hpet0: at MMIO 0xfed00000, IRQs 2, 8, 0, 0, 0, 0, 0, 0
    [ 0.200521] hpet0: 8 comparators, 64-bit 14.318180 MHz counter
    [ 0.202536] Switched to clocksource hpet
    [ 0.205461] pnp: PnP ACPI init
    [ 0.205473] ACPI: bus type PNP registered
    [ 0.205530] system 00:00: [mem 0xfed40000-0xfed44fff] has been reserved
    [ 0.205532] system 00:00: Plug and Play ACPI device, IDs PNP0c01 (active)
    [ 0.205540] pnp 00:01: [dma 4]
    [ 0.205552] pnp 00:01: Plug and Play ACPI device, IDs PNP0200 (active)
    [ 0.205566] pnp 00:02: Plug and Play ACPI device, IDs INT0800 (active)
    [ 0.205624] pnp 00:03: Plug and Play ACPI device, IDs PNP0103 (active)
    [ 0.205654] system 00:04: [io 0x0680-0x069f] has been reserved
    [ 0.205655] system 00:04: [io 0x0200-0x020f] has been reserved
    [ 0.205657] system 00:04: [io 0xffff] has been reserved
    [ 0.205658] system 00:04: [io 0xffff] has been reserved
    [ 0.205659] system 00:04: [io 0x0400-0x0453] could not be reserved
    [ 0.205660] system 00:04: [io 0x0458-0x047f] has been reserved
    [ 0.205662] system 00:04: [io 0x0500-0x057f] has been reserved
    [ 0.205663] system 00:04: [io 0x164e-0x164f] has been reserved
    [ 0.205664] system 00:04: Plug and Play ACPI device, IDs PNP0c02 (active)
    [ 0.205687] pnp 00:05: Plug and Play ACPI device, IDs PNP0b00 (active)
    [ 0.205719] system 00:06: [io 0x0454-0x0457] has been reserved
    [ 0.205721] system 00:06: Plug and Play ACPI device, IDs INT3f0d PNP0c02 (active)
    [ 0.205773] system 00:07: [io 0x0290-0x029f] has been reserved
    [ 0.205775] system 00:07: Plug and Play ACPI device, IDs PNP0c02 (active)
    [ 0.205807] system 00:08: [io 0x04d0-0x04d1] has been reserved
    [ 0.205809] system 00:08: Plug and Play ACPI device, IDs PNP0c02 (active)
    [ 0.205827] pnp 00:09: Plug and Play ACPI device, IDs PNP0c04 (active)
    [ 0.205968] pnp 00:0a: [dma 0 disabled]
    [ 0.206001] pnp 00:0a: Plug and Play ACPI device, IDs PNP0501 (active)
    [ 0.206148] system 00:0b: [mem 0xfed1c000-0xfed1ffff] has been reserved
    [ 0.206149] system 00:0b: [mem 0xfed10000-0xfed17fff] has been reserved
    [ 0.206151] system 00:0b: [mem 0xfed18000-0xfed18fff] has been reserved
    [ 0.206152] system 00:0b: [mem 0xfed19000-0xfed19fff] has been reserved
    [ 0.206153] system 00:0b: [mem 0xf8000000-0xfbffffff] has been reserved
    [ 0.206155] system 00:0b: [mem 0xfed20000-0xfed3ffff] has been reserved
    [ 0.206157] system 00:0b: [mem 0xfed90000-0xfed93fff] could not be reserved
    [ 0.206158] system 00:0b: [mem 0xfed45000-0xfed8ffff] has been reserved
    [ 0.206159] system 00:0b: [mem 0xff000000-0xffffffff] has been reserved
    [ 0.206160] system 00:0b: [mem 0xfee00000-0xfeefffff] could not be reserved
    [ 0.206162] system 00:0b: [mem 0xcf200000-0xcf200fff] has been reserved
    [ 0.206163] system 00:0b: Plug and Play ACPI device, IDs PNP0c02 (active)
    [ 0.206259] system 00:0c: [mem 0x20000000-0x201fffff] has been reserved
    [ 0.206260] system 00:0c: [mem 0x40004000-0x40004fff] has been reserved
    [ 0.206262] system 00:0c: Plug and Play ACPI device, IDs PNP0c01 (active)
    [ 0.206275] pnp: PnP ACPI: found 13 devices
    [ 0.206276] ACPI: bus type PNP unregistered
    [ 0.212140] pci 0000:00:1c.0: bridge window [io 0x1000-0x0fff] to [bus 02] add_size 1000
    [ 0.212142] pci 0000:00:1c.0: bridge window [mem 0x00100000-0x000fffff 64bit pref] to [bus 02] add_size 200000
    [ 0.212143] pci 0000:00:1c.0: bridge window [mem 0x00100000-0x000fffff] to [bus 02] add_size 200000
    [ 0.212170] pci 0000:00:1c.0: res[14]=[mem 0x00100000-0x000fffff] get_res_add_size add_size 200000
    [ 0.212171] pci 0000:00:1c.0: res[15]=[mem 0x00100000-0x000fffff 64bit pref] get_res_add_size add_size 200000
    [ 0.212172] pci 0000:00:1c.0: res[13]=[io 0x1000-0x0fff] get_res_add_size add_size 1000
    [ 0.212176] pci 0000:00:1c.0: BAR 14: assigned [mem 0xcf300000-0xcf4fffff]
    [ 0.212181] pci 0000:00:1c.0: BAR 15: assigned [mem 0xcf500000-0xcf6fffff 64bit pref]
    [ 0.212182] pci 0000:00:1c.0: BAR 13: assigned [io 0x2000-0x2fff]
    [ 0.212184] pci 0000:00:01.0: PCI bridge to [bus 01]
    [ 0.212185] pci 0000:00:01.0: bridge window [io 0xe000-0xefff]
    [ 0.212187] pci 0000:00:01.0: bridge window [mem 0xf7d00000-0xf7dfffff]
    [ 0.212189] pci 0000:00:01.0: bridge window [mem 0xe0000000-0xefffffff 64bit pref]
    [ 0.212191] pci 0000:00:1c.0: PCI bridge to [bus 02]
    [ 0.212193] pci 0000:00:1c.0: bridge window [io 0x2000-0x2fff]
    [ 0.212197] pci 0000:00:1c.0: bridge window [mem 0xcf300000-0xcf4fffff]
    [ 0.212200] pci 0000:00:1c.0: bridge window [mem 0xcf500000-0xcf6fffff 64bit pref]
    [ 0.212205] pci 0000:00:1c.4: PCI bridge to [bus 03]
    [ 0.212207] pci 0000:00:1c.4: bridge window [io 0xd000-0xdfff]
    [ 0.212211] pci 0000:00:1c.4: bridge window [mem 0xf7c00000-0xf7cfffff]
    [ 0.212217] pci 0000:04:00.0: PCI bridge to [bus 05]
    [ 0.212236] pci 0000:00:1c.5: PCI bridge to [bus 04-05]
    [ 0.212246] pci_bus 0000:00: resource 4 [io 0x0000-0x0cf7]
    [ 0.212247] pci_bus 0000:00: resource 5 [io 0x0d00-0xffff]
    [ 0.212248] pci_bus 0000:00: resource 6 [mem 0x000a0000-0x000bffff]
    [ 0.212249] pci_bus 0000:00: resource 7 [mem 0x000d0000-0x000d3fff]
    [ 0.212250] pci_bus 0000:00: resource 8 [mem 0x000d4000-0x000d7fff]
    [ 0.212251] pci_bus 0000:00: resource 9 [mem 0x000d8000-0x000dbfff]
    [ 0.212252] pci_bus 0000:00: resource 10 [mem 0x000dc000-0x000dffff]
    [ 0.212253] pci_bus 0000:00: resource 11 [mem 0x000e0000-0x000e3fff]
    [ 0.212254] pci_bus 0000:00: resource 12 [mem 0x000e4000-0x000e7fff]
    [ 0.212255] pci_bus 0000:00: resource 13 [mem 0xcf200000-0xfeafffff]
    [ 0.212257] pci_bus 0000:01: resource 0 [io 0xe000-0xefff]
    [ 0.212258] pci_bus 0000:01: resource 1 [mem 0xf7d00000-0xf7dfffff]
    [ 0.212259] pci_bus 0000:01: resource 2 [mem 0xe0000000-0xefffffff 64bit pref]
    [ 0.212260] pci_bus 0000:02: resource 0 [io 0x2000-0x2fff]
    [ 0.212261] pci_bus 0000:02: resource 1 [mem 0xcf300000-0xcf4fffff]
    [ 0.212262] pci_bus 0000:02: resource 2 [mem 0xcf500000-0xcf6fffff 64bit pref]
    [ 0.212263] pci_bus 0000:03: resource 0 [io 0xd000-0xdfff]
    [ 0.212264] pci_bus 0000:03: resource 1 [mem 0xf7c00000-0xf7cfffff]
    [ 0.212265] pci_bus 0000:04: resource 4 [io 0x0000-0x0cf7]
    [ 0.212266] pci_bus 0000:04: resource 5 [io 0x0d00-0xffff]
    [ 0.212267] pci_bus 0000:04: resource 6 [mem 0x000a0000-0x000bffff]
    [ 0.212269] pci_bus 0000:04: resource 7 [mem 0x000d0000-0x000d3fff]
    [ 0.212270] pci_bus 0000:04: resource 8 [mem 0x000d4000-0x000d7fff]
    [ 0.212271] pci_bus 0000:04: resource 9 [mem 0x000d8000-0x000dbfff]
    [ 0.212272] pci_bus 0000:04: resource 10 [mem 0x000dc000-0x000dffff]
    [ 0.212273] pci_bus 0000:04: resource 11 [mem 0x000e0000-0x000e3fff]
    [ 0.212274] pci_bus 0000:04: resource 12 [mem 0x000e4000-0x000e7fff]
    [ 0.212275] pci_bus 0000:04: resource 13 [mem 0xcf200000-0xfeafffff]
    [ 0.212276] pci_bus 0000:05: resource 8 [io 0x0000-0x0cf7]
    [ 0.212277] pci_bus 0000:05: resource 9 [io 0x0d00-0xffff]
    [ 0.212278] pci_bus 0000:05: resource 10 [mem 0x000a0000-0x000bffff]
    [ 0.212279] pci_bus 0000:05: resource 11 [mem 0x000d0000-0x000d3fff]
    [ 0.212280] pci_bus 0000:05: resource 12 [mem 0x000d4000-0x000d7fff]
    [ 0.212281] pci_bus 0000:05: resource 13 [mem 0x000d8000-0x000dbfff]
    [ 0.212282] pci_bus 0000:05: resource 14 [mem 0x000dc000-0x000dffff]
    [ 0.212283] pci_bus 0000:05: resource 15 [mem 0x000e0000-0x000e3fff]
    [ 0.212285] pci_bus 0000:05: resource 16 [mem 0x000e4000-0x000e7fff]
    [ 0.212286] pci_bus 0000:05: resource 17 [mem 0xcf200000-0xfeafffff]
    [ 0.212301] NET: Registered protocol family 2
    [ 0.212405] TCP established hash table entries: 65536 (order: 7, 524288 bytes)
    [ 0.212505] TCP bind hash table entries: 65536 (order: 8, 1048576 bytes)
    [ 0.212611] TCP: Hash tables configured (established 65536 bind 65536)
    [ 0.212623] TCP: reno registered
    [ 0.212629] UDP hash table entries: 4096 (order: 5, 131072 bytes)
    [ 0.212649] UDP-Lite hash table entries: 4096 (order: 5, 131072 bytes)
    [ 0.212685] NET: Registered protocol family 1
    [ 0.245935] pci 0000:01:00.0: Boot video device
    [ 0.245938] pci 0000:03:00.0: set MSI_INTX_DISABLE_BUG flag
    [ 0.245944] PCI: CLS 64 bytes, default 64
    [ 0.245971] Unpacking initramfs...
    [ 0.297147] Freeing initrd memory: 4348K (ffff880037772000 - ffff880037bb1000)
    [ 0.297165] PCI-DMA: Using software bounce buffering for IO (SWIOTLB)
    [ 0.297166] software IO TLB [mem 0xc4fcf000-0xc8fcf000] (64MB) mapped at [ffff8800c4fcf000-ffff8800c8fcefff]
    [ 0.297279] RAPL PMU detected, hw unit 2^-16 Joules, API unit is 2^-32 Joules, 3 fixed counters 163840 ms ovfl timer
    [ 0.297305] Scanning for low memory corruption every 60 seconds
    [ 0.297474] futex hash table entries: 1024 (order: 4, 65536 bytes)
    [ 0.307365] HugeTLB registered 2 MB page size, pre-allocated 0 pages
    [ 0.308202] zbud: loaded
    [ 0.308310] VFS: Disk quotas dquot_6.5.2
    [ 0.308329] Dquot-cache hash table entries: 512 (order 0, 4096 bytes)
    [ 0.308394] msgmni has been set to 15749
    [ 0.308421] Key type big_key registered
    [ 0.308524] Block layer SCSI generic (bsg) driver version 0.4 loaded (major 252)
    [ 0.308559] io scheduler noop registered
    [ 0.308561] io scheduler deadline registered
    [ 0.308589] io scheduler cfq registered (default)
    [ 0.308711] pcieport 0000:00:01.0: irq 42 for MSI/MSI-X
    [ 0.308910] pci_hotplug: PCI Hot Plug PCI Core version: 0.5
    [ 0.308920] pciehp: PCI Express Hot Plug Controller Driver version: 0.4
    [ 0.308938] vesafb: mode is 1366x768x32, linelength=5632, pages=0
    [ 0.308939] vesafb: scrolling: redraw
    [ 0.308940] vesafb: Truecolor: size=0:8:8:8, shift=0:16:8:0
    [ 0.308951] vesafb: framebuffer at 0xe0000000, mapped to 0xffffc90004e80000, using 4224k, total 4224k
    [ 0.350451] Console: switching to colour frame buffer device 170x48
    [ 0.391803] fb0: VESA VGA frame buffer device
    [ 0.391811] intel_idle: MWAIT substates: 0x1120
    [ 0.391812] intel_idle: v0.4 model 0x3A
    [ 0.391812] intel_idle: lapic_timer_reliable_states 0xffffffff
    [ 0.391916] GHES: HEST is not enabled!
    [ 0.391950] Serial: 8250/16550 driver, 4 ports, IRQ sharing disabled
    [ 0.412492] 00:0a: ttyS0 at I/O 0x3f8 (irq = 4, base_baud = 115200) is a 16550A
    [ 0.412763] Linux agpgart interface v0.103
    [ 0.412791] rtc_cmos 00:05: RTC can wake from S4
    [ 0.412895] rtc_cmos 00:05: rtc core: registered rtc_cmos as rtc0
    [ 0.412921] rtc_cmos 00:05: alarms up to one month, y3k, 242 bytes nvram, hpet irqs
    [ 0.412927] Intel P-state driver initializing.
    [ 0.412937] Intel pstate controlling: cpu 0
    [ 0.412950] Intel pstate controlling: cpu 1
    [ 0.412959] Intel pstate controlling: cpu 2
    [ 0.412996] Intel pstate controlling: cpu 3
    [ 0.413032] ledtrig-cpu: registered to indicate activity on CPUs
    [ 0.413152] TCP: cubic registered
    [ 0.413269] NET: Registered protocol family 10
    [ 0.413508] NET: Registered protocol family 17
    [ 0.413917] registered taskstats version 1
    [ 0.414415] Magic number: 10:384:80
    [ 0.414512] rtc_cmos 00:05: setting system clock to 2014-08-05 14:04:30 UTC (1407247470)
    [ 0.414604] PM: Hibernation image not present or could not be loaded.
    [ 0.415570] Freeing unused kernel memory: 1116K (ffffffff818df000 - ffffffff819f6000)
    [ 0.415572] Write protecting the kernel read-only data: 8192k
    [ 0.418429] Freeing unused kernel memory: 908K (ffff88000151d000 - ffff880001600000)
    [ 0.419683] Freeing unused kernel memory: 404K (ffff88000179b000 - ffff880001800000)
    [ 0.425699] random: systemd-tmpfile urandom read with 1 bits of entropy available
    [ 0.426625] systemd-udevd[58]: starting version 215
    [ 0.434065] i8042: PNP: No PS/2 controller found. Probing ports directly.
    [ 0.436383] serio: i8042 KBD port at 0x60,0x64 irq 1
    [ 0.436406] serio: i8042 AUX port at 0x60,0x64 irq 12
    [ 0.438395] ACPI: bus type USB registered
    [ 0.438416] usbcore: registered new interface driver usbfs
    [ 0.438422] usbcore: registered new interface driver hub
    [ 0.438568] usbcore: registered new device driver usb
    [ 0.438769] ehci_hcd: USB 2.0 'Enhanced' Host Controller (EHCI) Driver
    [ 0.438940] ehci-pci: EHCI PCI platform driver
    [ 0.439051] SCSI subsystem initialized
    [ 0.439069] ehci-pci 0000:00:1a.0: EHCI Host Controller
    [ 0.439073] ehci-pci 0000:00:1a.0: new USB bus registered, assigned bus number 1
    [ 0.439084] ehci-pci 0000:00:1a.0: debug port 2
    [ 0.439951] libata version 3.00 loaded.
    [ 0.442968] ehci-pci 0000:00:1a.0: cache line size of 64 is not supported
    [ 0.442981] ehci-pci 0000:00:1a.0: irq 23, io mem 0xf7e17000
    [ 0.452336] ehci-pci 0000:00:1a.0: USB 2.0 started, EHCI 1.00
    [ 0.452456] hub 1-0:1.0: USB hub found
    [ 0.452461] hub 1-0:1.0: 2 ports detected
    [ 0.452625] ehci-pci 0000:00:1d.0: EHCI Host Controller
    [ 0.452629] ehci-pci 0000:00:1d.0: new USB bus registered, assigned bus number 2
    [ 0.452639] ehci-pci 0000:00:1d.0: debug port 2
    [ 0.456535] ehci-pci 0000:00:1d.0: cache line size of 64 is not supported
    [ 0.456538] ehci-pci 0000:00:1d.0: irq 23, io mem 0xf7e16000
    [ 0.465651] ehci-pci 0000:00:1d.0: USB 2.0 started, EHCI 1.00
    [ 0.465817] hub 2-0:1.0: USB hub found
    [ 0.465823] hub 2-0:1.0: 2 ports detected
    [ 0.466005] xhci_hcd 0000:00:14.0: xHCI Host Controller
    [ 0.466009] xhci_hcd 0000:00:14.0: new USB bus registered, assigned bus number 3
    [ 0.466085] xhci_hcd 0000:00:14.0: cache line size of 64 is not supported
    [ 0.466103] xhci_hcd 0000:00:14.0: irq 43 for MSI/MSI-X
    [ 0.466251] hub 3-0:1.0: USB hub found
    [ 0.466259] hub 3-0:1.0: 4 ports detected
    [ 0.466483] xhci_hcd 0000:00:14.0: xHCI Host Controller
    [ 0.466485] xhci_hcd 0000:00:14.0: new USB bus registered, assigned bus number 4
    [ 0.466628] hub 4-0:1.0: USB hub found
    [ 0.466637] hub 4-0:1.0: 4 ports detected
    [ 0.466870] ata_piix 0000:00:1f.2: version 2.13
    [ 0.466965] ata_piix 0000:00:1f.2: MAP [ P0 P2 P1 P3 ]
    [ 0.619604] scsi0 : ata_piix
    [ 0.619931] scsi1 : ata_piix
    [ 0.620018] ata1: SATA max UDMA/133 cmd 0xf110 ctl 0xf100 bmdma 0xf0d0 irq 19
    [ 0.620024] ata2: SATA max UDMA/133 cmd 0xf0f0 ctl 0xf0e0 bmdma 0xf0d8 irq 19
    [ 0.620137] ata_piix 0000:00:1f.5: MAP [ P0 -- P1 -- ]
    [ 0.758810] usb 1-1: new high-speed USB device number 2 using ehci-pci
    [ 0.772097] ata_piix 0000:00:1f.5: SCR access via SIDPR is available but doesn't work
    [ 0.772607] scsi2 : ata_piix
    [ 0.772883] scsi3 : ata_piix
    [ 0.772956] ata3: SATA max UDMA/133 cmd 0xf0b0 ctl 0xf0a0 bmdma 0xf070 irq 19
    [ 0.772959] ata4: SATA max UDMA/133 cmd 0xf090 ctl 0xf080 bmdma 0xf078 irq 19
    [ 0.882597] hub 1-1:1.0: USB hub found
    [ 0.882674] hub 1-1:1.0: 6 ports detected
    [ 0.988607] usb 2-1: new high-speed USB device number 2 using ehci-pci
    [ 1.112512] hub 2-1:1.0: USB hub found
    [ 1.112572] hub 2-1:1.0: 8 ports detected
    [ 1.298309] tsc: Refined TSC clocksource calibration: 3398.999 MHz
    [ 1.378364] usb 2-1.5: new low-speed USB device number 3 using ehci-pci
    [ 1.408258] ata1.00: SATA link up 6.0 Gbps (SStatus 133 SControl 330)
    [ 1.408273] ata1.01: SATA link up 1.5 Gbps (SStatus 113 SControl 330)
    [ 1.421849] ata1.00: ATA-9: OCZ-AGILITY4, 1.4.1.3, max UDMA/133
    [ 1.421853] ata1.00: 125045424 sectors, multi 16: LBA48 NCQ (depth 0/32)
    [ 1.421859] ata1.01: ATAPI: Optiarc DVD RW AD-5280S, 1.01, max UDMA/100
    [ 1.428508] ata1.00: configured for UDMA/133
    [ 1.441760] ata1.01: configured for UDMA/100
    [ 1.442679] scsi 0:0:0:0: Direct-Access ATA OCZ-AGILITY4 1.4. PQ: 0 ANSI: 5
    [ 1.443880] scsi 0:0:1:0: CD-ROM Optiarc DVD RW AD-5280S 1.01 PQ: 0 ANSI: 5
    [ 1.467612] hidraw: raw HID events driver (C) Jiri Kosina
    [ 1.470021] usbcore: registered new interface driver usbhid
    [ 1.470024] usbhid: USB HID core driver
    [ 1.470596] input: Logitech USB Optical Mouse as /devices/pci0000:00/0000:00:1d.0/usb2/2-1/2-1.5/2-1.5:1.0/0003:046D:C05B.0001/input/input2
    [ 1.470731] hid-generic 0003:046D:C05B.0001: input,hidraw0: USB HID v1.11 Mouse [Logitech USB Optical Mouse] on usb-0000:00:1d.0-1.5/input0
    [ 1.531632] usb 2-1.6: new low-speed USB device number 4 using ehci-pci
    [ 1.623566] input: DELL Dell QuietKey Keyboard as /devices/pci0000:00/0000:00:1d.0/usb2/2-1/2-1.6/2-1.6:1.0/0003:413C:2106.0002/input/input3
    [ 1.623692] hid-generic 0003:413C:2106.0002: input,hidraw1: USB HID v1.10 Keyboard [DELL Dell QuietKey Keyboard] on usb-0000:00:1d.0-1.6/input0
    [ 1.967693] ata2.01: failed to resume link (SControl 30)
    [ 2.120931] ata2.00: SATA link up 6.0 Gbps (SStatus 133 SControl 330)
    [ 2.120945] ata2.01: SATA link down (SStatus 4 SControl 30)
    [ 2.128110] ata2.00: ATA-8: ST1500DL003-9VT16L, CC4A, max UDMA/133
    [ 2.128114] ata2.00: 2930277168 sectors, multi 16: LBA48 NCQ (depth 0/32)
    [ 2.141440] ata2.00: configured for UDMA/133
    [ 2.141636] scsi 1:0:0:0: Direct-Access ATA ST1500DL003-9VT1 CC4A PQ: 0 ANSI: 5
    [ 2.153040] sr0: scsi3-mmc drive: 48x/48x writer cd/rw xa/form2 cdda tray
    [ 2.153044] cdrom: Uniform CD-ROM driver Revision: 3.20
    [ 2.153124] sd 0:0:0:0: [sda] 125045424 512-byte logical blocks: (64.0 GB/59.6 GiB)
    [ 2.153280] sr 0:0:1:0: Attached scsi CD-ROM sr0
    [ 2.153296] sd 0:0:0:0: [sda] Write Protect is off
    [ 2.153301] sd 0:0:0:0: [sda] Mode Sense: 00 3a 00 00
    [ 2.153326] sd 0:0:0:0: [sda] Write cache: enabled, read cache: enabled, doesn't support DPO or FUA
    [ 2.153429] sd 1:0:0:0: [sdb] 2930277168 512-byte logical blocks: (1.50 TB/1.36 TiB)
    [ 2.153432] sd 1:0:0:0: [sdb] 4096-byte physical blocks
    [ 2.153528] sd 1:0:0:0: [sdb] Write Protect is off
    [ 2.153531] sd 1:0:0:0: [sdb] Mode Sense: 00 3a 00 00
    [ 2.153639] sd 1:0:0:0: [sdb] Write cache: enabled, read cache: enabled, doesn't support DPO or FUA
    [ 2.175762] sda: sda1 sda2
    [ 2.190742] sdb: sdb1
    [ 2.191322] sd 0:0:0:0: [sda] Attached SCSI disk
    [ 2.191353] sd 1:0:0:0: [sdb] Attached SCSI disk
    [ 2.297544] Switched to clocksource tsc
    [ 2.521461] device-mapper: uevent: version 1.0.3
    [ 2.521594] device-mapper: ioctl: 4.27.0-ioctl (2013-10-30) initialised: [email protected]
    [ 3.194646] random: nonblocking pool is initialized
    [ 3.442872] EXT4-fs (dm-0): mounted filesystem with ordered data mode. Opts: (null)
    [ 3.687624] systemd[1]: Configuration file /etc/systemd/system/netctl@ethernet\x2ddhcp.service is marked world-inaccessible. This has no effect as configuration data is accessible via APIs without restrictions. Proceeding anyway.
    [ 3.691036] systemd[1]: [/etc/systemd/system/vncserver@:1.service:1] Assignment outside of section. Ignoring.
    [ 3.786773] EXT4-fs (dm-0): re-mounted. Opts: data=ordered
    [ 3.846387] systemd-udevd[195]: starting version 215
    [ 3.955208] input: Power Button as /devices/LNXSYSTM:00/LNXSYBUS:00/PNP0C0C:00/input/input4
    [ 3.955211] ACPI: Power Button [PWRB]
    [ 3.955251] input: Power Button as /devices/LNXSYSTM:00/LNXPWRBN:00/input/input5
    [ 3.955252] ACPI: Power Button [PWRF]
    [ 3.971958] snd_hda_intel 0000:00:1b.0: irq 44 for MSI/MSI-X
    [ 3.972032] snd_hda_intel 0000:01:00.1: Handle VGA-switcheroo audio client
    [ 3.972035] snd_hda_intel 0000:01:00.1: Force to non-snoop mode
    [ 3.972053] snd_hda_intel 0000:01:00.1: irq 45 for MSI/MSI-X
    [ 3.982591] input: HDA ATI HDMI HDMI/DP,pcm=3 as /devices/pci0000:00/0000:00:01.0/0000:01:00.1/sound/card1/input6
    [ 3.982615] input: HDA ATI HDMI HDMI/DP,pcm=7 as /devices/pci0000:00/0000:00:01.0/0000:01:00.1/sound/card1/input7
    [ 3.982636] input: HDA ATI HDMI HDMI/DP,pcm=8 as /devices/pci0000:00/0000:00:01.0/0000:01:00.1/sound/card1/input8
    [ 3.982656] input: HDA ATI HDMI HDMI/DP,pcm=9 as /devices/pci0000:00/0000:00:01.0/0000:01:00.1/sound/card1/input9
    [ 3.982676] input: HDA ATI HDMI HDMI/DP,pcm=10 as /devices/pci0000:00/0000:00:01.0/0000:01:00.1/sound/card1/input10
    [ 3.982697] input: HDA ATI HDMI HDMI/DP,pcm=11 as /devices/pci0000:00/0000:00:01.0/0000:01:00.1/sound/card1/input11
    [ 3.983309] wmi: Mapper loaded
    [ 3.983960] mei_me 0000:00:16.0: irq 46 for MSI/MSI-X
    [ 4.016049] ACPI Warning: SystemIO range 0x000000000000f040-0x000000000000f05f conflicts with OpRegion 0x000000000000f040-0x000000000000f04f (\_SB_.PCI0.SBUS.SMBI) (20140214/utaddress-258)
    [ 4.016054] ACPI: If an ACPI driver is available for this device, you should use it instead of the native driver
    [ 4.016101] shpchp: Standard Hot Plug PCI Controller Driver version: 0.4
    [ 4.022693] [drm] Initialized drm 1.1.0 20060810
    [ 4.032772] ACPI: Video Device [GFX0] (multi-head: yes rom: no post: no)
    [ 4.032996] thermal LNXTHERM:00: registered as thermal_zone0
    [ 4.032998] ACPI: Thermal Zone [TZ00] (28 C)
    [ 4.033145] acpi device:46: registered as cooling_device4
    [ 4.033214] input: Video Bus as /devices/LNXSYSTM:00/LNXSYBUS:00/PNP0A08:00/LNXVIDEO:00/input/input12
    [ 4.033243] thermal LNXTHERM:01: registered as thermal_zone1
    [ 4.033245] ACPI: Thermal Zone [TZ01] (30 C)
    [ 4.033309] ACPI: Fan [FAN0] (off)
    [ 4.033333] ACPI: Fan [FAN1] (off)
    [ 4.033354] ACPI: Fan [FAN2] (off)
    [ 4.033375] ACPI: Fan [FAN3] (off)
    [ 4.033398] ACPI: Fan [FAN4] (off)
    [ 4.037199] sound hdaudioC0D0: autoconfig: line_outs=4 (0x1c/0x19/0x22/0x23/0x0) type:line
    [ 4.037202] sound hdaudioC0D0: speaker_outs=0 (0x0/0x0/0x0/0x0/0x0)
    [ 4.037203] sound hdaudioC0D0: hp_outs=1 (0x1d/0x0/0x0/0x0/0x0)
    [ 4.037204] sound hdaudioC0D0: mono: mono_out=0x0
    [ 4.037205] sound hdaudioC0D0: dig-out=0x20/0x21
    [ 4.037205] sound hdaudioC0D0: inputs:
    [ 4.037207] sound hdaudioC0D0: Rear Mic=0x1a
    [ 4.037208] sound hdaudioC0D0: Front Mic=0x1e
    [ 4.037209] sound hdaudioC0D0: Line=0x1b
    [ 4.045615] input: HDA Intel PCH Rear Mic as /devices/pci0000:00/0000:00:1b.0/sound/card0/input13
    [ 4.045640] input: HDA Intel PCH Front Mic as /devices/pci0000:00/0000:00:1b.0/sound/card0/input14
    [ 4.045658] input: HDA Intel PCH Line as /devices/pci0000:00/0000:00:1b.0/sound/card0/input15
    [ 4.045676] input: HDA Intel PCH Line Out Front as /devices/pci0000:00/0000:00:1b.0/sound/card0/input16
    [ 4.045694] input: HDA Intel PCH Line Out Surround as /devices/pci0000:00/0000:00:1b.0/sound/card0/input17
    [ 4.045711] input: HDA Intel PCH Line Out CLFE as /devices/pci0000:00/0000:00:1b.0/sound/card0/input18
    [ 4.045728] input: HDA Intel PCH Line Out Side as /devices/pci0000:00/0000:00:1b.0/sound/card0/input19
    [ 4.045747] input: HDA Intel PCH Front Headphone as /devices/pci0000:00/0000:00:1b.0/sound/card0/input20
    [ 4.045764] input: HDA Intel PCH HDMI/DP,pcm=7 as /devices/pci0000:00/0000:00:1b.0/sound/card0/input21
    [ 4.045781] input: HDA Intel PCH HDMI/DP,pcm=8 as /devices/pci0000:00/0000:00:1b.0/sound/card0/input22
    [ 4.084103] microcode: CPU0 sig=0x306a9, pf=0x2, revision=0xa
    [ 4.101114] [drm] Memory usable by graphics device = 2048M
    [ 4.101117] checking generic (e0000000 420000) vs hw (d0000000 10000000)
    [ 4.101753] microcode: CPU1 sig=0x306a9, pf=0x2, revision=0xa
    [ 4.101765] microcode: CPU2 sig=0x306a9, pf=0x2, revision=0xa
    [ 4.101773] microcode: CPU3 sig=0x306a9, pf=0x2, revision=0xa
    [ 4.101803] microcode: Microcode Update Driver: v2.00 <[email protected]>, Peter Oruba
    [ 4.117554] input: PC Speaker as /devices/platform/pcspkr/input/input23
    [ 4.119413] mousedev: PS/2 mouse device common for all mice
    [ 4.122449] i915 0000:00:02.0: irq 47 for MSI/MSI-X
    [ 4.122456] [drm] Supports vblank timestamp caching Rev 2 (21.10.2013).
    [ 4.122457] [drm] Driver supports precise vblank timestamp query.
    [ 4.122795] iTCO_vendor_support: vendor-support=0
    [ 4.123419] iTCO_wdt: Intel TCO WatchDog Timer Driver v1.11
    [ 4.123440] iTCO_wdt: Found a Panther Point TCO device (Version=2, TCOBASE=0x0460)
    [ 4.123499] iTCO_wdt: initialized. heartbeat=30 sec (nowayout=0)
    [ 4.132527] [drm] Wrong MCH_SSKPD value: 0x20100406
    [ 4.132529] [drm] This can cause pipe underruns and display issues.
    [ 4.132529] [drm] Please upgrade your BIOS to fix this.
    [ 4.146676] i915 0000:00:02.0: No connectors reported connected with modes
    [ 4.146679] [drm] Cannot find any crtc or sizes - going 1024x768
    [ 4.147000] checking generic (e0000000 420000) vs hw (d0000000 10000000)
    [ 4.147051] i915 0000:00:02.0: fb1: inteldrmfb frame buffer device
    [ 4.147052] i915 0000:00:02.0: registered panic notifier
    [ 4.147063] [drm] Initialized i915 1.6.0 20080730 for 0000:00:02.0 on minor 0
    [ 4.153004] AVX version of gcm_enc/dec engaged.
    [ 4.153783] alx 0000:03:00.0 eth0: Qualcomm Atheros AR816x/AR817x Ethernet [c8:60:00:98:ce:45]
    [ 4.163501] asus_wmi: ASUS WMI generic driver loaded
    [ 4.165770] asus_wmi: Initialization: 0x0
    [ 4.165783] asus_wmi: BIOS WMI version: 0.9
    [ 4.165823] asus_wmi: SFUN value: 0x0
    [ 4.166095] input: Eee PC WMI hotkeys as /devices/platform/eeepc-wmi/input/input25
    [ 4.168099] asus_wmi: Backlight controlled by ACPI video driver
    [ 4.170681] kvm: disabled by bios
    [ 4.179593] kvm: disabled by bios
    [ 4.188390] [drm] radeon kernel modesetting enabled.
    [ 4.188423] checking generic (e0000000 420000) vs hw (e0000000 10000000)
    [ 4.188424] fb: switching to radeondrmfb from VESA VGA
    [ 4.188437] Console: switching to colour dummy device 80x25
    [ 4.188600] [drm] initializing kernel modesetting (VERDE 0x1002:0x683D 0x1462:0x2710).
    [ 4.188609] [drm] register mmio base: 0xF7D00000
    [ 4.188609] [drm] register mmio size: 262144
    [ 4.188651] ATOM BIOS: 113
    [ 4.188769] radeon 0000:01:00.0: VRAM: 1024M 0x0000000000000000 - 0x000000003FFFFFFF (1024M used)
    [ 4.188770] radeon 0000:01:00.0: GTT: 1024M 0x0000000040000000 - 0x000000007FFFFFFF
    [ 4.188771] [drm] Detected VRAM RAM=1024M, BAR=256M
    [ 4.188772] [drm] RAM width 128bits DDR
    [ 4.188797] [TTM] Zone kernel: Available graphics memory: 4033182 kiB
    [ 4.188798] [TTM] Zone dma32: Available graphics memory: 2097152 kiB
    [ 4.188799] [TTM] Initializing pool allocator
    [ 4.188802] [TTM] Initializing DMA pool allocator
    [ 4.188814] [drm] radeon: 1024M of VRAM memory ready
    [ 4.188815] [drm] radeon: 1024M of GTT memory ready.
    [ 4.188823] [drm] Loading VERDE Microcode
    [ 4.192707] systemd-udevd[202]: renamed network interface eth0 to enp3s0
    [ 4.226833] [drm] radeon/VERDE_mc2.bin: 31500 bytes
    [ 4.228027] [drm] Internal thermal controller with fan control
    [ 4.228070] [drm] probing gen 2 caps for device 8086:151 = 261ad03/e
    [ 4.234178] [drm] radeon: dpm initialized
    [ 4.235973] [drm] GART: num cpu pages 262144, num gpu pages 262144
    [ 4.236543] [drm] probing gen 2 caps for device 8086:151 = 261ad03/e
    [ 4.236546] [drm] PCIE gen 3 link speeds already enabled
    [ 4.246119] [drm] PCIE GART of 1024M enabled (table at 0x0000000000276000).
    [ 4.246215] radeon 0000:01:00.0: WB enabled
    [ 4.246217] radeon 0000:01:00.0: fence driver on ring 0 use gpu addr 0x0000000040000c00 and cpu addr 0xffff88021f6f1c00
    [ 4.246219] radeon 0000:01:00.0: fence driver on ring 1 use gpu addr 0x0000000040000c04 and cpu addr 0xffff88021f6f1c04
    [ 4.246220] radeon 0000:01:00.0: fence driver on ring 2 use gpu addr 0x0000000040000c08 and cpu addr 0xffff88021f6f1c08
    [ 4.246221] radeon 0000:01:00.0: fence driver on ring 3 use gpu addr 0x0000000040000c0c and cpu addr 0xffff88021f6f1c0c
    [ 4.246222] radeon 0000:01:00.0: fence driver on ring 4 use gpu addr 0x0000000040000c10 and cpu addr 0xffff88021f6f1c10
    [ 4.246703] radeon 0000:01:00.0: fence driver on ring 5 use gpu addr 0x0000000000075a18 and cpu addr 0xffffc900192b5a18
    [ 4.246704] [drm] Supports vblank timestamp caching Rev 2 (21.10.2013).
    [ 4.246705] [drm] Driver supports precise vblank timestamp query.
    [ 4.246720] radeon 0000:01:00.0: irq 48 for MSI/MSI-X
    [ 4.246728] radeon 0000:01:00.0: radeon: using MSI.
    [ 4.246746] [drm] radeon: irq initialized.
    [ 4.704412] [drm] ring test on 0 succeeded in 2 usecs
    [ 4.704417] [drm] ring test on 1 succeeded in 1 usecs
    [ 4.704420] [drm] ring test on 2 succeeded in 1 usecs
    [ 4.704483] [drm] ring test on 3 succeeded in 4 usecs
    [ 4.704488] [drm] ring test on 4 succeeded in 1 usecs
    [ 4.892271] [drm] ring test on 5 succeeded in 2 usecs
    [ 4.892276] [drm] UVD initialized successfully.
    [ 4.892454] [drm] ib test on ring 0 succeeded in 0 usecs
    [ 4.892510] [drm] ib test on ring 1 succeeded in 0 usecs
    [ 4.892562] [drm] ib test on ring 2 succeeded in 0 usecs
    [ 4.892627] [drm] ib test on ring 3 succeeded in 0 usecs
    [ 4.892703] [drm] ib test on ring 4 succeeded in 1 usecs
    [ 5.045155] [drm] ib test on ring 5 succeeded
    [ 5.045348] [drm] Radeon Display Connectors
    [ 5.045349] [drm] Connector 0:
    [ 5.045350] [drm] DP-4
    [ 5.045351] [drm] HPD4
    [ 5.045352] [drm] DDC: 0x6540 0x6540 0x6544 0x6544 0x6548 0x6548 0x654c 0x654c
    [ 5.045352] [drm] Encoders:
    [ 5.045353] [drm] DFP1: INTERNAL_UNIPHY2
    [ 5.045353] [drm] Connector 1:
    [ 5.045354] [drm] HDMI-A-4
    [ 5.045355] [drm] HPD1
    [ 5.045355] [drm] DDC: 0x6570 0x6570 0x6574 0x6574 0x6578 0x6578 0x657c 0x657c
    [ 5.045356] [drm] Encoders:
    [ 5.045356] [drm] DFP2: INTERNAL_UNIPHY2
    [ 5.045357] [drm] Connector 2:
    [ 5.045358] [drm] DVI-I-1
    [ 5.045358] [drm] HPD2
    [ 5.045359] [drm] DDC: 0x6560 0x6560 0x6564 0x6564 0x6568 0x6568 0x656c 0x656c
    [ 5.045359] [drm] Encoders:
    [ 5.045360] [drm] DFP3: INTERNAL_UNIPHY
    [ 5.045361] [drm] CRT1: INTERNAL_KLDSCP_DAC1
    [ 5.073351] EXT4-fs (sda1): mounting ext2 file system using the ext4 subsystem
    [ 5.092640] EXT4-fs (dm-1): mounted filesystem with ordered data mode. Opts: data=ordered
    [ 5.108315] EXT4-fs (sda1): mounted filesystem without journal. Opts: (null)
    [ 5.117016] [drm] fb mappable at 0xE0479000
    [ 5.117017] [drm] vram apper at 0xE0000000
    [ 5.117018] [drm] size 4325376
    [ 5.117019] [drm] fb depth is 24
    [ 5.117019] [drm] pitch is 5632
    [ 5.117106] fbcon: radeondrmfb (fb0) is primary device
    [ 5.149170] Console: switching to colour frame buffer device 170x48
    [ 5.150711] radeon 0000:01:00.0: fb0: radeondrmfb frame buffer device
    [ 5.150750] [drm] Initialized radeon 2.38.0 20080528 for 0000:01:00.0 on minor 1
    [ 5.335178] EXT4-fs (dm-2): mounted filesystem with ordered data mode. Opts: data=ordered
    [ 5.341840] [drm] Enabling RC6 states: RC6 on, RC6p on, RC6pp off
    [ 5.345398] systemd-journald[174]: Received request to flush runtime journal from PID 1
    [ 5.384082] systemd-journald[174]: File /var/log/journal/3ceb5e0931f846a88e9868dfe8919c31/system.journal corrupted or uncleanly shut down, renaming and replacing.
    [ 5.571040] alx 0000:03:00.0: irq 49 for MSI/MSI-X
    [ 5.571201] IPv6: ADDRCONF(NETDEV_UP): enp3s0: link is not ready
    [ 10.650843] alx 0000:03:00.0: irq 49 for MSI/MSI-X
    [ 10.650985] IPv6: ADDRCONF(NETDEV_UP): enp3s0: link is not ready
    [ 15.592516] alx 0000:03:00.0 enp3s0: NIC Up: 100 Mbps Full
    [ 15.592732] IPv6: ADDRCONF(NETDEV_CHANGE): enp3s0: link becomes ready

    Is this the log of a failed boot or of a successful one? If it is a successful one, please provide the log of a failed boot. This log seems to say that there are 3 displays detected, so I think this is a normal boot.
    What I would like to see is if the failed boot starts X or not. That is, assuming you use X. When the boot fails, do you see messages on your screen before it goes black?

  • Crackling, Left Rear Channel noise, IRQs, 4 Gigs of Memory, fixes and problems with XFi Fatal

    Hello fellow troubleshooters. Well I've been working on my XFI issues since there are so many of them trying to make the one piece in my newly built system work as intended. I will put my hardware info below this post for comparison purposes if it helps you at all or for feedback/ideas. Well first off I had the crackling noise popping so on even when my machine was idle. If you have not done this yet do it
    !!! Start, Control Panel, Sounds Speech and Audio Device, Change Speaker Settings, Advanced (in device volume), ok now there is a bunch of sliders go to "options" check everything, ok now that you see all the sliders mute Everything besides: Play Control, Wave, CD Player for testing purpose. You will probably hear a difference as you do it. Especially Mic 2. Ok well that issue resolved my popping crackling noises when idle. Ok so I still have a shared IRQ issue since I have an Asus A8N32-SLI Deluxe board and the slots go as such PCI-E, PCI, PCI, PCI-E, PCI. Well since the GeForce 7800 GTX cards I have take up not just the PCI-E slot, but also the PCI slot is covered from the Huge Fan. Then the Same thing for the Second graphics card. So I have only one slot that works for my PCI Fatalty sound card. Well this forces me to share PCI IRQ between one of the Video Cards and the Sound Card. Its not a "conflict" it is simply sharing the IRQ, after the above issue fixed my popping issue this no longer was a concern. Now my big issue is that I sent my Sub Woofer in for RMA, I have the Gigaworks S750 7. THX speakers, they are great but when I really crank up the volume on them I would get the sound like a speaker was blown in the left rear channel, so I swapped another speaker in its place and I have the same problem. So the RMA folks said to send in the Sub Woofer which cost me over $30 to ship the thing only to have them tell me there is no problem. Well I had recently done RMAs on my sound card, both Video Cards, and my mother board too in hopes of fixing the next problem. So everything is new though I got a refurb on the mobo. So I'm just waiting on my Sub woofer now so I'm using my headphones and guess what I'm finding there is this noise in the left speaker, an issue I sent the headphones back for a long time ago when I was using them waiting to buy my speakers. I have the Creative Pro Gamer headphones. So now I read a post about someone else with the same issue left channel, and I have to wonder I am not alone and that usually means in Creative Labs land there probably is others with this issue that have spouses that wont let them stretch their audiophile legs with extreme volume, if this is you try it out kick up the bass, and see if you have this problem too, if so please post it here. I have no clue on this one and I am open to any ideas. Ok and the last issue!! This is the real problem I'm facing now. I play EQ2 I love my MMO titles with the occassional single player title for those short stints at the computer between work, parenting, and stuff my wife demands be started before she finishes speaking of it (those of you married know what I'm talking about). I have 2 operating systems, XP Home, and XP Pro 64. Home I use for Office, graphic design, and general applications. XP Pro 64 I use purely for gaming. All my games are installed through this OS which is on my 2 74 Gig Raptors in Raid 0, I have another Partition for XP Home, and a 3rd for all the game installs. So I recently found that after selecting Extreme Graphics option in EQ2 then moving the rest of the sliders to Max that my G5 keyboard which has a performance monitor in it showing the amount of Ram usage showed me hitting about 90% and would spilke at the same time as I found I had frame rate slowdown. So I decided to get 2 more gigs of Corsair Twin XMS 3500Pro 024x2 memory bumping me up to 4 gigs. Well I had to go into the bios I found and change a memory setting to discrete and enable the memory hole in order for XP Pro 64 and the motherboard to see the memory. At this time I was working on other things with my computer, and suddenly the popping noise came back so I'm pissed now.... But oddly its not happening in XP home, only in XP 64. So I'm thinking I may have to go to XP home for my gaming OS, then just before I install home I remember that XP home wont register 4 gigs of memory.... So I go turn off the memory hole and discrete settings and this sets the memory to 2 gigs.... Crackling sound in ALL EAX GAMES goes away.... So now clearly my issue with my sound card and EAX crackling noise is Memory related somehow. Now I have isolated it to 4 gigs of memory, but it makes me think of those folks with this issue perhaps something is amiss with their memory and how it works with timing, or onboard memory on the sound card which is a first time memory is put on a sound card?.... Any input is appreciated as to how to repair this issue, thanks for reading, below is my system set up.
    rocessor >
    ?Model:???? x AMD Athlon(tm) 64 X2 Dual Core Processor
    ??????4400+
    ?Speed:???? 2.2GHz
    ?Model Number:???? 4400 (estimated)
    ?Performance Rating:??? PR7072 (estimated)
    ?Cores per Processor:?? 2 Unit(s)
    ?Threads per Core:??? Unit(s)
    ?Type:????? Dual-Core
    ?Internal Data Cache:?? 2x 64kB Synchronous, Write-Back, 2-way set,
    ??????64 byte line size
    ?L2 On-board Cache:?? 2x MB ECC Synchronous, Write-Back, 6-way
    ??????set, 64 byte line size
    ?<Mainboard >
    ?Bus(es):???? ISA PCI PCIe USB FireWire/394 i2c/SMBus
    ?MP Support:???? 2 Processor(s)
    ?MP APIC:???? No
    ?System BIOS:??? American Megatrends Inc. 8.2
    ?System:????? System manufacturer System Product Name
    ?Mainboard:???? ASUSTeK Computer INC. A8N32-SLI-Deluxe
    ?Total Memory:???? 3.9GB DDR-SDRAM
    ?<Chipset >
    ?Model:???? Advanced Micro Devices (AMD) Athlon 64 /
    ??????Opteron HyperTransport Technology
    ??????Configuration
    ?Front Side Bus Speed:?? 2x 005MHz (200MHz data rate)
    ?Total Memory:???? 4GB DDR-SDRAM
    ?Memory Bus Speed:??? 2x 200MHz (400MHz data rate)
    ?<Video System >
    ?Monitor/Panel:??? Default Monitor
    ?Monitor/Panel:??? HP D895 HP P20 2-inch Monitor
    ?Adapter:???? NVIDIA GeForce 7800 GTX
    ?Adapter:???? NVIDIA GeForce 7800 GTX
    ?hysical Storage Devices >
    ?Removable Dri've:??? Floppy disk dri've
    ?Hard Disk:???? WDC WD2500KS-00MJB0 (233GB)
    ?Hard Disk:???? WDC WD3200JD-00KLB0 (298GB)
    ?Hard Disk:???? NVIDIA? STRIPE? 38.49G
    ?Hard Disk:???? Generic USB CF Reader USB Device
    ?Hard Disk:???? Generic USB MS Reader USB Device
    ?Hard Disk:???? Generic USB SD Reader USB Device
    ?Hard Disk:???? Generic USB SM Reader USB Device
    ?CD-ROM/DVD:???? HL-DT-ST DVD-ROM GDR860B (CD 48X Rd) (DVD 6X
    ??????Rd)
    ?CD-ROM/DVD:???? HL-DT-ST DVD-ROM GDR860B (CD 48X Rd) (DVD 6X
    ??????Rd)
    ?CD-ROM/DVD:???? HL-DT-ST DVD-ROM GDR860B (CD 48X Rd) (DVD 6X
    ??????Rd)
    ?CD-ROM/DVD:???? HL-DT-ST DVDRAM GSA-463B (CD 40X Rd, 40X Wr)
    ??????(DVD 5X Rd, 5X Wr)
    ?<Logical Storage Devices >
    ?.44MB 3.5" (A:??? N/A
    ?Applications - games - storage:233GB (5GB, 65% Free Space) (NTFS)
    ?Xp home (D:???? 24GB (5.6GB, 23% Free Space) (NTFS)
    ?CD-ROM/DVD (E:??? N/A
    ?Xp 64 (F:???? 24GB (5GB, 63% Free Space) (NTFS)
    ?Raptor games (G:?? 90GB (7GB, 8% Free Space) (NTFS)
    ?Ssdisk (H:???? 629MB (CDFS)
    ?Bf2xpack cd (I:??? 677MB (CDFS)
    ?Farstone (J:??? 00MB (CDFS)
    ?Removable Dri've (K:?? N/A
    ?Removable Dri've (L:?? N/A
    ?Removable Dri've (M:?? N/A
    ?Back up dri've (N:??? 298GB (3GB, 44% Free Space) (NTFS)
    ?Removable Dri've (O:?? N/A?EvolovE

    Evolve,
    I have the a8n-sli Premium which as you stated is basically the same board with a couple extra items. I have the latest beta bios ver -06. Since the early fall release the option which we will be talking about was available in the premium board which it I remember was Bios rev 9. I would download the latest bios rev.
    07.04 (latest beta?or go with 06)?and flash in. Here are the steps to get the proper memory options to work and I have also included my system specs to compare.
    ) Hit Del to get into Bios
    2) Go to the second tab on the top of the screen "Advanced"
    3) Select the first option in the menu "CPU Configuration"
    4) Select the first option in the "CPU Configuration" menu called "DRAM Configuration"
    5) Select Manual configuration from the first Menu item.
    6) The last two options in the same menu for DRAM are s/w remapping over 4G and h/w remapping over 4G. Select the "s/w remapping option over 4G" and enable it. Disable the "h/w remapping over 4G."?
    7) Hit f0 and save the config.
    You should now at post have 4GBws total but only 3GBs of usable memory and your X-fi should crush it in XP64 and XP32.
    My Specs
    A8n-sli premium (Bios -06)
    amd X2 4400 (~2.5 GHZ)
    4GB LL patriot memory (~228 HZ)
    X-Fi Extreme Music
    LSI 320-2e PCI express SCSI RAID controller (256MB buffer)
    2x Seagate Cheata 5K.3?dri'ves
    All water cooled
    Good Luck
    PapaH
    By the way this is defiantly a XP64 driver problem because even with h/w remapping enabled in XP32 the card sounds fine. It only happens in XP64.

  • Please help [Realtek LAN NIC problem]

    Hi everyone, this might be a long post but PLEASE read it if you have the time, you might just know the solution to this problem. to begin with, here is my system:
    Windows 2000 pro sp4
    AMD Athlon64 3000+
    MSI K8T Neo (BIOS rev. 1.10)
    1 GB (2x512) PC3500 Mushkin level 2 hi performance @ 2-3-2-6 timings
    Samsung SATA 160 GB hard drive
    ATI Radeon 9700 pro (catalyst 4.1)
    Lite On 52x-32x-52x IDE CD Drive
    Enermax EG465P-VE FC (460W) 3.3V/35A , 5V/35A , 12V/33A
    *There are not any other PCI cards installed.
    Now, here is the problem:
    I did not notice the problem right away, you will not notice this if you are doing normal browsing or downloads. It came to my attention while I was receiving a file on IRC (using mIRC). while I was recieving the file I noticed that, somehow, I could no longer access the internet at all (neither on IRC, http, ftp .. nothing). I tried to find out why, I couldn't. so I rebooted the system and tried to continue receiving that file ... same thing happens. after a while of digging around my system and experimenting I found that sends from certain people will cause the problem, and i simply need to restart to get back online. this will happen always whenever those certain people send me anything. so, what's going on:
    1 - Windows 2000 pro is freshly installed and up to date. i tried XP, it had the same problem; however, 2000pro is the operating system i will be using.
    2 - the client is not the problem because i tried another one and the same thing happened. I have also tested 2 other computers and they worked fine (same file .. same person). note that the download was going faster on the other 2 computers.
    3 - it is not the router because a direct link to the modem did not solve the problem. also, the other 2 computers had no problem with the router.
    4 - i tested the Realtek driver that was included on the motherboard CD as well as the updated drivers from realtek website. that also did not help.
    5 - windows reports that the device (realtek NIC adapter) is working properly and that there are no conflicts. realtek diagnostics utility also reports no problems.
    6 - Realtek's Gigabit NIC shares IRQ 16 with the radeon 9700 pro, so I figured that i could reserve some of main memory to IRQ 16 to make sure things run with maximum stability:
    on system.ini added the line -> IRQ[16] = 8192 (reserve 8MB of main memory for IRQ 16). this did not help. so i removed it.
    7 - changing the NIC setting from "auto negotiation" to "100Mbps/Full duplex" did not help either.
    8 - one time, the Realtek diagnostics utility was able to reload the device driver, and of course, i was able to go online without restarting. this happened only once. note that I tried to unload/reload the device through device manager many times but i always failed and then i have to press the power switch or reset button to actually reboot. normal windows shutdown/reboot is not possible. the same thing happens when Realtek's diagnostics finishes a test and tries to reload the driver (remember, it only succeeded once).
    9 - system logs do not seem to report any problem. i even tried using inspectr.exe to try and find the reason for the driver crash but no crash was detected.
    10- disabling the IEEE 1394 controller did not help.
    it is obvious that there is something wrong with the driver, but there is a possibility it could be the board/device. if the driver is "flakey", it will mess up. if the device/chip/board is not working properly, then the driver will get stuck just as well.
    so, the solution?
    I- Hit the wall with my head 7 times (2-3-2) then roll on the ground for a few minutes .. get up and hit the wall 13 more times (2-3-2-6) and then roll on the ground and sleep.
    or
    II- burn it all .. yes ... BURN IT ALL. MOAHAHAHAHAH!!!
    or
    III- RMA board or change it :(
    I'm trying to decide whether it is the board or if it is the driver. I'm trying to find any excuse not to RMA or change the board. I will be installing linux, and networking is important to get rest of the files I need. I really would like not to rely on flakey hardware or driver. if it is the chip, i have to RMA. if it is the driver, change MB or get a NIC card and install it until realtek decides that it is a good idea to fix the driver.
    i tried to check realtek's website but there was very little or no real helpful information to the end user (either that, or i was too upset to find the info i need on their website). I wish they had a forum like this one.
    That is basically what i was thinking about .. of course, i could be wrong and the solution might be simple (i wish).
    any suggestions, tweaks, patches, information that you guys know about are appreciated and may be of great help. Are there any setting in the BIOS that i need to set in some way to make sure this works properly? would the new BIOS revision 1.20 fix this?
    I apologize for the lengthy post. I believe that I've managed to fry whatever brain cells I had left over the past few days. So,  I apologize for any spelling/grammer mistakes
    thank you in advance

    Blaming every problem on the MSI K8T NEO FSR on a 350w power source is utter crap!  
    Why would ANY Computer hardware shops even SELL SYSTEMS on a 350w powersource on the thousands if a 350watt power source wouldnt be enough for the motherboard, what you are saying that hundreds of HW stores are just saying FU to every customer they sell a computer unit WHICH COMES PRE-EQUIPPED with a 350W powersource!!! I've seen various configurations using a 350w power source working just fine!
    I simply DO NOT believe that the system aint getting enough power, that's bull! This would cause considerable UNSTABILITIES and other problems on the system besides dysfunctional S-ATA Hard drives and NIC problems, eg. like artifacts while playing games, crackling in audio, bluescreens and other symptoms!
    I just noticed today that my on board NIC had jammed while downloading Torrent files, had to reboot my cable modem, this could be nothing and could simply be an ISP matter, or it could be that my K8T NEO FSR also has a problem with the NIC, again i stress that i havent done really any testing so this raving could be about nothing.
    I solved my S-ATA problem by changing back to a similiar IDE 8MB cache 7200 rpm Samsung 160 GB drive. No problems what so ever with register / file corruption! I've also been in contact with VIA who are currently investigating problems with the 8237 Southbridge controller equipped motherboards like the K8T NEO FSR (http://www.viaarena.com -> forums)

Maybe you are looking for

  • Intermittent scratching noise on pb 1.67 hard drive

    I've done a search on this issue and know it has been discussed, but I was not able to find anything dealing specifically with my issue. I have a pb 1.67 with an 80g hd that makes an intermitten whirring, actually more like a scratching sound. I've n

  • Photo sync in full size resolution

    Hey there, since 3 day I have now a Ipad 3. gen and have some questions regarding the transfer from high resolution photos (8mpx) to the Ipad. Currently I only knew the way to syncronize with Itunes. When I'm doing this, the photos seems to be resize

  • It is not an option in my iTunes to "Choose Store Update iTunes Match.

    I wish to add some new tunes I have ripped from original cd's and it is not an option in my iTunes after I choose " store " to " Update Match "

  • Pictures will only partually display on stage or not display at all.

    Sometimes this happens.  At other times nothing will display at all.  I have also had a portion of the picture duplicated multiple times on the stage.  Does anyone know what is happening?

  • Automatic reservation for Internal in VMS

    Hi, I have a requirement to enhance in VMS for " automatically assign an internal reservation to a vehicle object once a sales order has been cancelled". Please suggest me the possibilities for enhance the request. Thanks