IRQ problems?, especially with USB.... read this

Summary: the following things are listed to help people configure or disable USB and USB IRQ related options, some steps may help diagnose/eliminate other IRQ problems. Some Operating Systems/Motherboards may have Similiar or Alternative ways to preform the following options,(Some may not be compatible with these Options):
From initial installation problems to suddenly not working USB, cleaning up the Device manager in Safe mode is the first step. Many hardware related problems in Windows can be traced to ghost devices and duplicate device entries. Obsolete and/or duplicate devices can ONLY be seen and removed in Windows Safe Mode. This procedure MUST be performed in SAFE MODE.
USB can only share its IRQ with other USB Host controllers (such as a USB upgrade card, if applicable) and IRQ Holder for PCI Steering. (Some of the newer motherboards can share USB Devices with their On-Board Devices,ex: K7N2 Delta
In most cases for mother boards the First and Last PCI slot share the same IRQ as the AGP slot. This is not always the case, and is usually addressed in the motherboard's manual. In some motherboards there are other slots that share IRQ's with other on board devices, these can lead to conflicts and errors later; try changing cards in PCI slots around.
Sometimes you may find that when you have installed a new card (or device) into the system, other devices such as the sound card may stop working. Once again, the resource configuration needs to be changed. Do so by going to Control Panel, System, Hardware, Device Manager, (Com1) ,or other port's properties, disable usage. This is also the best way of disabling hardware so that if necessary the customer can turn the hardware back on through windows rather than having to play in the BIOS.After disabling a device in the BIOS boot to Safe Mode and delete the device from the Windows Device Manager. If the device is not removed from the Windows Device Manager in Safe Mode, Windows will continue to recognize the device and Windows will continue to assign it an IRQ.
In some versions of the Award, AMI and Phenix bios you can select Plug and Play OS installed. This option lets you decide whether windows should handle the IRQ routing of devices or if the BIOS should handle the routing. Please note that if this option is enabled windows will show a completely different setup of IRQ's then what the BIOS reports You may wish to toggle this option if you find that moving the card dosn't work. This in some cases will change the way windows will assign IRQ's. In most cases this will help but not in all.
Another section that you might want to look at is if the IRQ's are being assigned manually or automatically. Sometimes it is better to manually assign IRQ's and other times it is better to automatically assign them.You can do so by entering your BIOS... should be listed under PNP/OS or PNP/PCI Configuration. ( You must disable Plug N Play feature for this to work!)
Properly installed IRQ Steering is critical to correctly working USB. If IRQ Steering is disabled the likely cause is improper BIOS settings. See the section on BIOS Settings. Go to Control Panel, System, Hardware, Device Manager, System Devices, PCI Bus...If you do not have the following options, then obviously your system shouldn't be configured this way. Seek alternative means to enable/disable them. View Status, go to Settings tab, Use Hardware should be enabled, go to IRQ Steering tab... The following options should be checked... Use IRQ Steering, Get IRQ table using ACPI BIOS, GET IRQ table using MS Specification table, Get IRQ table from Real Mode PCIBIOS 2.1 call.... Under IRQ Routing Status the following should be displayed: (AMD) system should read: IRQ Steering Enabled, IRQ Table read from ACPI BIOS. (Intel) system should read: IRQ Table read from MS IRQ Routing Specification), IRQ Miniport Data processed successfully, IRQ Miniport loaded successfully. If IRQ Steering is not enabled. Reboot the system to the BIOS setup (Usually holding the DEL key at bootup) and Enable (Plug and Play Operating System). Set (Assign IRQs) AUTO or System. IRQ Steering is essential to proper USB connectivity. BIOS control of Power Management should be Disabled or set to User...
If all the above doesn't work, you can look at the hardware in the computer and disable any that is not nessasary. This will free up some IRQs and on the next reboot the IRQs may be reshuffled to a better configuration. Common hardware that is good to disable are com ports and USB controllers.  If you are not using your serial port for anything, disable COM1. If you are not using your USB try disabling the USB controllers and hubs. If you are using a USB mouse, try pulling it into the PS/2 port if possible. All these things will free up and change the available IRQ's, and allow USB devices to automatically select them.
Disable USB Error Detection In Windows Standard Mode, Device Manager, USB Host Controllers, (SiS, Standard, ect..)USB Open Host Controller, Advanced, Enable the function (Disable USB Error Detection).
With some motherboards you may need to install the newest version of the motherboard drivers and also may need to flash the BIOS.An example of this is VIA motherboards. The VIA or Apollo chipset boards require an update for their IRQ routing with windows. This update helps fix problems such as loss of data and such.
If you still cannot isolate USB to it’s own IRQ, changing the I/O range of USB sometimes works.
Possibly your last resort upgrading to USB by PCI/USB upgrade card is a recommended solution for systems with non-functioning onboard USB host controllers. Properly Installed the USB upgrade host controller should share the same IRQ as the onboard USB host controller. Check the motherboard manual or Manufacturers Web Site and install the new card into a PCI Slot that shares it's IRQ with USB. Do NOT disable USB in the BIOS as the upgrade card may not work if you do.
If that won't fix it, you may want to contact your mother board's manufacturer, or retailer who sold you the unoperable System components, to see if your System is under any kind of waranty/recall; then order a new motherboard and components...there is always the possibility you will  end up with same problem. Or you can contact a computer tech in your area. Goodluck...
Misc Tips....
Check all Physical Connections (This includes: Motherboard mounting, cables, plugs, and visibly damaged components)...
Don't use cables longer than what you need, this can decreases efficiency and or causes System instability...
Check your Voltages in BIOS, and on your PSU (power supply unit); make sure your system is not underpowered...
Check your CPU/System Temperature, check airflow/fans, then check with your CPU manufacturer for acceptable settings...
Check BIOS, Drivers, Firmware, and Software for latest settings/updates...
Check Compatability (can find information in your Motherboard, BIOS, and Device Manuals...
Don't Overclock or Tweak settings you don't understand, unless you like the smell of toast...
And finally, don't me scared to ask... no one here will think less of you for seeking info/help from those who know...

Also if this has helped you or someone else in anyway please reply.
-Michael

Similar Messages

  • As we are having a problem explicit with Adobe Reader 11.0.07, we are interested in news and dates for coming updates to Adobe Reader. Can I find information about this anywhere ?

    As we are having a problem explicit with Adobe Reader 11.0.07, we are interested in news and dates for coming updates to Adobe Reader. Can I find information about this anywhere ?

    Hello Claus,
    you could have a look here: http://helpx.adobe.com/security/products/flash-player/apsb14-13.html  and in german language http://www.chip.de/downloads/Adobe-Reader_12998358.html
    In all These cases Google could be "your friend".
    Hans-Günter

  • MSi Dragon Editon 2 problems booting with usb mice

    Hi to all people. I have a problem with my laptop. If i update my BIOS with versions newer tan E1763IMS.50V the laptop doesn´t boot with usb mice connected. I think i  answer this in the past but with not solution and now i ask again  thinking some people have a solution now.I have checked with differents EC versions and  BIOS E1763IMS.50V and with all versions works fine. If i update the BIOS E1763IMS.50V with other newer BIOS the problem appears. When the pc is started  and Windows 8.1 is charged i can connect the mouse and works fine too. I have checked with various mices and with all the problem appears. The only BIOS that works fine is E1763IMS.50V.
    Thanks a lot for your help

    I borrowed a GT70, plugged my SteelSeries Rival optical mouse and flashed with the same 50V version to the laptop. It boots & works normally.
    And then I flashed to 518 version. It still boots & works normally.
    So maybe your problem is not on the mouse?
    Did it boot up if unplugging the mouse?

  • Podpress problems, especially with regards to formatting and coding

    Here is my RSS url: http://www.regrettablesincerity.com/?feed=podcast
    I've been having a lot of problems trying to figure out the coding that goes with files that were too large (over 8 MB) to be uploaded through Wordpress, and had to be uploaded via FTP.
    In Podpress' general settings, the URI link is: http://www.regrettablesincerity.com/wp-content/uploads
    The suggestion for the load paths for media directory is: /home/content/e/l/m/elmooxygen/html/wp-content/uploads
    I'm assuming that this refers to the larger files, so do I put my website's name before the /home? And if so, what do I put in the article itself? [Located here: http://www.regrettablesincerity.com/?p=4513
    I've gone with: http://www.regrettablesincerity.com/home/content/e/l/m/elmooxygen/html/wp-conten t/uploads/audio/Outlook%20Radio%20Interview%20Ex-Gay.mp3
    I've tried a myriad of a variations, without the %20, removing the word uploads, etc. No matter which I've tried, Podpress can't figure out how big or how long the file is, insisting it is 1 byte. I've made the proper correction and it says as much in my feed link, but if you click on the specific file on the feed page, it is different than the URL I provided, and will not change back. It now reads as: http://www.regrettablesincerity.com/podpress_trac/feed/4513/0/Outlook%20Radio%20 Interview%20Ex-Gay.mp3 I don't know why the podpress_trac thing is in there, but it won't go back to what I told no matter what.
    My overall goal is to be able to just have the RSS point to a specific page which has all of my director interviews and podcasts: http://www.regrettablesincerity.com/?page_id=846 However, once I tried that, the description given for the podcast on Itunes (only the first one, the Rolf De Heer interview, seemed to be read by the feed) was incorrect and it also said that the length of the podcast was 1 minute and 1 second, when it is in fact well over an hour. On top of that, you couldn't download it at all.
    Now I don't mind if I have to put the podcasts in individual posts if that solves the problem, but what about when there are more than one audio file in a specific post, because I broke them up in parts? I did a 3 part interview here: http://www.regrettablesincerity.com/?p=3921 As you can see in my feed link, http://www.regrettablesincerity.com/?feed=podcast , it only lists the first file, not all three.
    The smaller issues have to do with Itunes and my feed link ignoring the fact that I've changed the description within the specific settings for Itunes section in Podpress, but it still shows the original version, no matter what I do (this is a problem because some of the podcasts are in posts with film reviews, and so the articles have different explanations than would work in Itunes for a potential downloader). Also, my stats test fails in the general settings section of Podpress. I tried all different combinations, at the moment it is: Use WP permalinks for the Method and Full for the logging. A weirder problem is that when I have the Podpress plug-in activated, Wordpress will no longer give me any resize options when uploading a photo, I have to do the cropping on outside software.
    Below is my feed link:
    http://www.feedvalidator.org/check.cgi?url=http%3A%2F%2Fwww.regrettablesincerity .com%2F%3Ffeed%3Dpodcast
    It has some problems that I have no idea how to solve, since I've even tried to correct the "object" issue, but Wordpress puts the word back in when I hit update. The enclosure problem, I have no clue on, because there's no text I can find to delete. Line 112 is a mystery too, because I don't even know where that line would be.
    Thanks to anyone who manages to read this entire post, let alone make suggestions. I've spent several weeks trying to figure this all out but have been stymied in terms of help by all manner of Apple customer service reps and there's no contact option on Podpress' main page. I'm sure I'll think of more issues I'm having if I tried, so I better stop before those who browse this topic grow far more impatient.
    Message was edited by: Adam Lippe

    To answer a couple of your queries:
    The FeedValidator comments mostly refer to things inside the 'content:encoded' tag which is not relevant to iTunes.
    Each 'item' tag can only contain one enclosure. The second enclosure will be ignored.
    The '%20' business is because you have spaces in your filenames. Spaces are not allowed in a URL and so browsers and programs writing feed replace them with the HTML code for a space. This shouldn't cause problems.
    Your main difficulty seems to be in providing a valid URL for your episode media files. If these are being hosted by Wordpress then it's something you will have to take up with them. Most people upload the files to a server or an iDisk and place the URL in the feed (the episodes don't have to be on the same server as the feed): really the URL should be directly to the feed rather than using a script to call it or a redirect.

  • Problem connecting with USB Hard drive on Router since upgrade to Lion

    Over the past year we have been slowly getting set up to have a hard drive with our photos networked so we can access from all home computers. We have a CineRAID hard drive storage tower w/one 2TB Seagate HD (allows for 4 hard drives). We have collected pictures from all computers onto the hard drive. Up until recently, we have had the system connected directly to one computer to allow transfer of files more easily. When I recently attached it back to the Netgear WNDR3700v2 router, I can see the drive (called ReadyShare, instead of the drive name "Photos & Videos") in the Finder, but I cannot access the drive; says "Connection Failed" and clicking brings up the box to connect as if to another computer.
    I had set this up when we first got the hard drive in January and everything worked fine, i.e., I could see and access the pictures that had been transferred to the drive, without having to logon to the hard drive. The only thing that I know has changed is migrating my computer from Snow Leopard to Lion. Is there some new protocol for accessing this type system, or have I inadvertently switched/changed something else, that I no longer remember?

    Over the past year we have been slowly getting set up to have a hard drive with our photos networked so we can access from all home computers. We have a CineRAID hard drive storage tower w/one 2TB Seagate HD (allows for 4 hard drives). We have collected pictures from all computers onto the hard drive. Up until recently, we have had the system connected directly to one computer to allow transfer of files more easily. When I recently attached it back to the Netgear WNDR3700v2 router, I can see the drive (called ReadyShare, instead of the drive name "Photos & Videos") in the Finder, but I cannot access the drive; says "Connection Failed" and clicking brings up the box to connect as if to another computer.
    I had set this up when we first got the hard drive in January and everything worked fine, i.e., I could see and access the pictures that had been transferred to the drive, without having to logon to the hard drive. The only thing that I know has changed is migrating my computer from Snow Leopard to Lion. Is there some new protocol for accessing this type system, or have I inadvertently switched/changed something else, that I no longer remember?

  • Safari Memory Leak (especially with Google Reader)

    Safari starts gobbling up memory with use, never releasing it. I have turned off extensions, moved all internet plugins to disabled directory, restarted, etc. but nothing helps. Right now its sitting at 1.5GB real memory usage.
    One quick way for me to replicate this issue is to go through a few hundred google reader items. It never releases memory even when I close that google reader tab. Any ideas or suggestions? Thanks!

    Hi
    If a new account is the same, you've done it all; bar a fresh install, unless you're quite certain everything's as standard...
    http://bugreport.apple.com and/or google feedback.

  • "Insufficient data for an image" when opening a PDF, even with Adobe Reader 11.0.06

    I have extracted some pages from a large, scanned, PDF into a separate document, using a product called Nuance PDF Converter 7, and when we try to open that with Adobe Reader 11.0.06, we receive the error "Insufficient data for an image".  I have read that this error was supposed to be fixed with the latest version of Adobe Reader 11, but I have installed that, and it doesn't help.

    I am also having this problem, especially with scanned documents. Since I need to download scanned documents in my work this is a big problem!Sometimes I can read but not save the document, sometimes one or two of the pages will be blank from the start. I have the latest version of Adobe Reader XI (11.0.10). I tried reducing the page zoom, a suggested workaround on this page: Acrobat: “Insufficient data for an image” error after updating to 10.1.4 or 9.5.2,  but that did not help at all. FWIW I use a Windows 8.1 PC with 4 GB RAM. I usually download PDFs from the internet using Firefox.

  • IPod Mini only mounts with USB

    My daughter has 2 minis- Pink & Blue and she uses a G4 1G RAM, OS 10.3.9
    She updated Pink using firewire, it synched fine. When she tried to update Blue, it wasn’t recognized.
    IPod software is up to date on both. Both fully charged, hold switch off, etc.
    I did everything Apple recommends, I reset, I manually put it in disk mode, checked and rechecked cables, all to no avail. I couldn’t restore using the updater as it wouldn’t mount - even in disk mode.
    This was only with the Blue mini, the Pink is recognized fine.
    After a frustrating hour or so, I was about to just give up and send it for repair when I remembered the USB cable and decided to try that.
    It worked! I restored the software, remounted and reinstalled all of her music. I ejected the Blue from the USB and tried to plug it in using the firewire cable.
    Nothing. No ipod mounts. Again, the Pink is fine.
    So I have 2 minis, one works with Firewire, the other only with USB.
    This isn’t a huge problem. But I am wondering why? Has anyone ever had this problem?
    Thanks,
    Norma

    Try to reset it.
    Press and hold the MENU and CENTER buttons - at the same time - until you see the Apple logo. This should take about 6 seconds. Also, you want to do this procedure while your iPod is connected to your computer. Ipods are supposed to work with USB port cable and AC Adapters, not only car chargers.
    If this doesn't work, then try to update it using iPod Updater software. Open iPod Update, plug in your iPod to your computer and wait until the software recognizes it. Once it does, you should be able to click on the "Update" button. If you can't, click "Restore"

  • Xfdf post problem introduced in Adobe Reader 9.1.2?

    Hi,
    In the past couple weeks, we've had many customers reporting errors with using the xfdf post-back feature of Adobe Acrobat docuements we use.
    They said this was not a problem before they upgraded to Adobe Reader 9.1.2.
    I have not been able to reproduce the problem here with Adobe Reader 9.1.2, but I'm guessing that maybe their configuration is slightly different from my test configuration of machine/Adobe Reader 9.1.2...
    To summarize how we use xfdf post-back:
    1.) The Adobe Acrobat .pdf has a button image with the Acrobat variant of javascript handling a "button push" to do an http post of the xfdf data to our server.
    2.) The server then processes the xfdf data.
    This has always worked fine in the past, but would appear to (under some yet unspecified client-side circumstances), cause an error.  Note:  the server-side appears to not be the root of the problem because the same server is used with the client-machines (client-machines meaning the acrobat plug-in inside an IE browser) that do work, and also with the client-machines that don't work.
    Additional note:  The client-machines that do work...always work.  The client-machines that don't work, never work.
    Attached is a screenshot of the Microsoft Fiddler (protocol monitor tool) request and response data of the xfdf post.
    Thoughts on what might be the problem?
    Thanks!

    Thank you very much for your response but unfortunately none of the suggested solutions have worked.  When pressing F8 then F8 again, the picture icon toolbar toggles between not being shown and then being shown again so no Save options appear.  When pressing F9, nothing happens at all.  When pressing Ctrl+Shift+S an adobe message appears in the middle of the screen stating the following "This document does not allow you to save any changes you have made to it unless you are using Adobe Acrobat 9, Pro 9 or Pro Extended 9.  You will only be saving a copy of the original document.  Do you want to continue?"  It then prompts you with "OK" or "Cancel".  Upon pressing "OK" absolutely nothing happens.   I have seen this type of message many times before when trying to save pdf files and it has successfully saved the file but for some reason nothing happens in this version of adobe reader.  Do you have any other thoughts at all as to how to solve this?

  • How do I open a pdf file on my iPad with Adobe reader.

    I can't open a pdf file in an email with Adobe reader.

    This document explains how:
                     Opening PDF Files in Reader for iOS (iPhone and iPad)

  • Solve Problem with USB Connection / Read this it i...

    i can not load maps on my n97 mini. the error 'usb connection lost...' show on the screen in map loader but at the first day i had no problems.
    i wonder why. i look for driver, ovi suite, pc suite, usb at the pc, read in the forum and many more. but nothing solve the problem. after 2 days i use accidentally the original cable which comes with the nokia n97 mini (it is a ca-101) and all my problems are gone ! bevor i use an 'old' ca-101 cabel from my n82 and i can not upload a map but the handy is shown in the pc system with all drivers and no problems. only loading big megabytes data on the handy crashes the usb connection. with the n97 mini ca-101 cabel no problem with gigabytes. i look for another ca-101 cable from the 6220 from my wife and i have the same problems (i never used bevor this cable for a connection to any handy ! it was brand new !). it seems that 'old' ca-101 cabels do not handle big data with the n97 mini. i look on the gold spring clips in the micro usb and could see that the are a little smaller and not so high in the jack in the 'old' cables. all three cables are original from nokia and not from china ! if you are also problems look on the produkt id on the plastics. if the letters are gold you have a cable like my n97 mini cable, but if the letters are black on a silver button you have an 'old' cable.
    i hope i can help another with this maniac problem
    greetings

    I can verify this on win7 with latest PC suite.
    I was using the cable that came with my 6500s as I didn't want to tackle the rats nest of wiring behind my pc.
    This cable is a ca101 with silver writing on the plastic tab, made in China.
    Using this cable, my 6620c would not complete a backup, it would just sit for hours on 2-4%.
    Tested with the ca101 cable that came with the 6620c (gold writing, made in Thailand).
    This time the backup completed in about 2 minutes.
    Thank you so much for finding this, it has been driving me crazy!

  • Please Read this ! USB Sound Blaster 24-Bit External : The Story of the endless problem

    In order to keep the good behavior here (I`m really pissed off !) I just?want to tell you something (this is ESPECIALLY for all the guys from the stuff)?Before 2 days I`ve decided to buy a new sound system for my room. I bought myself Creative Inspire t600 5. surround system. Cool. I was very happy. I?needed only to buy a sound card?working with 5. because I have a notebook DELL INSPIRON 50 who has only 2 canals. So in order to be everything beautiful I gave $70 for Usb sound blaster 24-Bit external. And from that time the problems began. In short :? I was using Vista but I found out that it wont work with this soundcard. The first problem : Didn`t identify the device. I tried with several drivers... Nope. No sound card with Vista.(This problem seems to appearance with many owners like me)?I pluged the usb soundcard in my old pc running XP and it worked . PERFECTLY. So I removed Vista from my notebook and intalled XP. This took me whole day to rebuild all my software. Finally it left to set up the sound drivers. The cherry of the icecream. Aaaaand ..... **bleep**. When I play?any track it CRACKLES. Again problem appearanced with many here. I tried to find out here what is the problem but unfortunately as u can see my english is quite bad?so I cant understand?what I need.I really like Creative but if they cant manage this problem I will?no longer buy their stuffs??JUST PLEASE SOMEBODY ANSWER ME IS THERE ANY SOLUTION FOR THIS OR NOT. I JUST WANT STRAIGHT ANSWERPS : Please do not delete my post. I know there are plenty like this. I dont want this crackles

    well ?

  • If you're having problems with USB ports, read on...

    i'm reading that alot of people on here are having problems with their front (or top) usb on their cases not working with their k7n2 boards.  i have come across the correct solution to this problem in one of the posts (after having solved the problem on my own), however noone has posted the solution by itself on this forum so everyone can easily see it.
    The trick is to make sure that pin 10 (at least on a K7n2 delta-L), the pin labeled USBOC (USB Open Connection), is wired to NOTHING.  If the connector to your front usb ports is fused into one giant connector and it HAS a wire that will connect to this pin (labeled GND2 or Shield or something), CUT THAT WIRE.  Pin 10 on JUSB2 (at least on a K7n2 delta-L) must be OPEN.  If this pin IS connected to something (even if it is only GND), the motherboard will think something is connected to this usb port and you will get many unknown devices listed in your windows device manager and the rest of your usb ports may or may not work.
    As a general rule of thumb, if a pin on a motherboard is labeled OC for "Open Connection" and you wire something to it, you're asking for trouble.
    If you cannot understand this you should not be attempting to wire a motherboard in the first place. 
    Here is a picture to go along with this discussion.  If you cannot see this picture, I am sorry for it has probably been removed from the place I posted it online as I cannot attach pictures physically to this post.  If someone here has a way to permanently host this picture and post it to this thread permanently, that would be wonderful.
    In summary: all usb ports/headers have only four pins associated with it (VCC, USB+, USB-, GND).  If the connector (whether it's one big connector or individual sockets) to your front/top usb port has 5 sockets, don't connect the 5th socket to anything.  That goes for any case/motherboard combination.  This is what i'm talking about above.  I have no idea why motherboard and case manufacturers have a 5th pin involved in any way on either the pin or socket side.  It is not used for usb.
    EDIT:  I just noticed this has already been discussed in the trouble shooting guide in the above sticky post.  oh well, now we have a pretty picture to go along with it (i hope).

    :-D)Hello guys,
    as promised I come back here to give the results of my tests... and I have to say that you saved my day (even if I had to open back 60 secured cases).
    So the solution was the right one, when I unplugged the "ground" end of the front USB connector cable from the USBOC pin, those connectors finally worked as expected with USB 2.0 compliant devices.
    So thank you really much for this very usefull information !
    And even if maybe it's not only MSI's fault, I still believe that more information on those connectors in the user's manual would be really usefull (who knows what USBOC means except a few people and who could imagine that pluggin on it a "ground" cable would make it unserviceable ??). And who ever saw a user's manual bundled with a case ?? it's pretty unusual  
    Hope that someone at MSI will read that and take it into consideration, not for me (because now I'm aware) but for the thousands other consumers that will feel a little bit "annoyed" with that issue. I don't think that adding one line about it in user's manuals would be so much expensive  
    But I'm quite lucky myself... being able to understand and write english (even if I still have some progress to do  ) gave me the possibility to find the solution... but a lot of my french fellows can't do that... and there's no french forum here... How can they do ? They rely on user's manual
    Best regards,
    Nicolas

  • RE: [Adobe Reader] when i open pdf file it open all the pages but some pages give error massage (there was error processing a page,there was a problem reading this document 110) but if i open this page which give me error with google chrome it's work ? i

    HelloThank's for your helpsI hope this document is helpfulBest Regards,
    Date: Sun, 22 Jun 2014 17:10:17 -0700
    From: [email protected]
    To: [email protected]
    Subject:  when i open pdf file it open all the pages but some pages give error massage (there was error processing a page,there was a problem reading this document 110) but if i open this page which give me error with google chrome it's work ? if you can help me th
        when i open pdf file it open all the pages but some pages give error massage (there was error processing a page,there was a problem reading this document 110) but if i open this page which give me error with google chrome it's work ? if you can help m
        created by Anoop9178 in Adobe Reader - View the full discussion
    Hi,
    Would it be possible for you to share the document?
    Regards,
    Anoop
         Please note that the Adobe Forums do not accept email attachments. If you want to embed a screen image in your message please visit the thread in the forum to embed the image at https://forums.adobe.com/message/6485431#6485431
         Replies to this message go to everyone subscribed to this thread, not directly to the person who posted the message. To post a reply, either reply to this email or visit the message page:
         To unsubscribe from this thread, please visit the message page at . In the Actions box on the right, click the Stop Email Notifications link.
         Start a new discussion in Adobe Reader by email or at Adobe Community
      For more information about maintaining your forum email notifications please go to http://forums.adobe.com/thread/416458?tstart=0.

    thank's for reply and your help
    i did the step's that you told me but  i still have the same problem
                                     i have the latest v.11.0.7
    i
    i disable the protected mode

  • When i open pdf file it open all the pages but some pages give error massage (there was error processing a page,there was a problem reading this document 110) but if i open this page which give me error with google chrome it's work ? if you can help me th

    when i open pdf file it open all the pages but some pages give error massage (there was error processing a page,there was a problem reading this document 110) but if i open this page which give me error with google chrome it's work ?
    if you can help me thank's
    [email address removed by host]

    thank's for reply and your help
    i did the step's that you told me but  i still have the same problem
                                     i have the latest v.11.0.7
    i
    i disable the protected mode

Maybe you are looking for