Is 10.1.0.7 database certified for OIM 9.1.0.1?

Is 10.1.0.7 version certified for OIM 9.1.0.1?
Per documentastion 11.1.0.6 or later patch sets are certified
Does this mean 11.1.0.6 patch set 1 or 11.1.0.7 is also included?
I appreciate your feedback

Hello,
11.1.0.6 and later patch sets*11.1.0.7* is a later patchset.
Best regards,
Jean-Valentin

Similar Messages

Any Oracle database personal edition certified for Windows 7/32bit?

Is any Oracle database Personal edition certified for Windows 7/32bit? I spent an hour at least searching for this but no chance.
Thank you.

Currently, only 11gR2 and 10.2.0.5 are certified on Win 7 Professional or higher - Home versions are not supported.
HTH
Srini

Is OIM 9.1.0.1 certified for 10.1.0.7 database?

Per documentation OIM 9.1.0.1 is certified for Oracle 11g Enterprise edition 11.1.0.6 and later patch sets.
Does this include 10.1.0.7 or only 11.1.0.6 patch set x are certified.
I would appreciate your feedback

Hello,
11.1.0.6 and later patch sets*11.1.0.7* is a later patchset.
Best regards,
Jean-Valentin

10gR2 Transportable Tablespaces Certified for EBS 11i for Migration

Guys,
Good news is Now 10gR2 Transportable Tablespaces Certified for EBS 11i,
Here is Steven chan blog link, I know personally how much i struggled with expdp and impdp on linux, it sounds good news who is migrating 11i .
http://blogs.oracle.com/stevenChan/2010/04/10gr2_xtts_ebs11i.html?utm_source=feedburner&utm_medium=email&utm_campaign=Feed%3A+OracleE-BusinessSuiteTechnology+%28Oracle+E-Business+Suite+Technology%29

To migrate the database you can either use Transportable tablespaces or export/import.
Transportable Tablespaces
New Source Database Added for EBS 12 + 11gR2 Transportable Tablespaces
https://blogs.oracle.com/stevenChan/entry/new_source_database_added_for
New Source Databases Added for Transportable Tablespaces + EBS 11i
https://blogs.oracle.com/stevenChan/entry/new_source_databases_added_for
Database Migration using 11gR2 Transportable Tablespaces Now Certified for EBS 12
https://blogs.oracle.com/stevenChan/entry/database_migration_using_11gr2_transportable
Export/Import
Export/import process for 12.0 or 12.1 using 11gR1 or 11gR2 (Doc ID 741818.1)
Export/import notes on Applications 11i Database 11g (Doc ID 557738.1)
If your application will remain on the same OS (which is different than the target database OS) then please also see:
Oracle EBS R12 with Database Tier Only Platform on Oracle Database 11.2.0 (Doc ID 456347.1)
Using Oracle EBS with a Split Configuration Database Tier on 11gR2 (Doc ID 946413.1)
Oracle E-Business Suite Upgrades and Platform Migration (Doc ID 1377213.1)
Thanks,
Hussein

How to install Oracle Database 10g for windos vista

hia
i am new student in a collage and i started learn SQL command
i want to practice SQL command in my Laptop
i downloaded Oracle Database 10g Release 2 (10.2.0.3) for windows vista
but i have difficult to install it i mean i wana know the steps to install oracle
could u show me by photo or video how to install oracle in my labtob
also some of my friend said u should have a local server in ur labtop to make oracle programe work .... is it true??
if it correct learn me how to make it and connect it to oracle
also some of my friend said u should have a this information form oracle web side
USER NAME :
PASSWORD:
HOTAGE STRING :
please help me

haloooooo
i am waiting for somebody to help me
nobody can
pliz pliz plizPlease, please, please understand that this forum is populated with unpaid volunteers. It's not a help desk.
The complete installation installation guide is included with the installation software. It is also part of the exhaustively complete documentation set for every oracle product found at tahiti.oracle.com. Go there, select your product and version. When you arrive at the page for your specific product version, somewhere on that page (location varies between versions) you will find a link to the installation guide.
Also please note that there are several versions of Vista, and the Oracle db is not certified for all of them, but only for specific versions.

Database respository for Enterprise Manager Grid 10.2.0.2.0

Does anyone know if enterprise manager grid 10.2.0.2.0 repository database is able to be run on a 10.2.0.2.0 database.
The documentation states that it is certified to run on 10.1.0.4.0 or higher database, but I think this means only 10.1.x database not 10.2
I have checked the certification page, and it only indicates the 10.2.0.1.0 release of the software is able to run on 10.1.0.4.0, the mention of 10.2 database is planned.

Suggest you recheck the certification page, and click on the link Oracle Enterprise Manager 10g Grid Control Release 2 (10.2.0.2).
That will tell you 10.2.0.2 database is certified for a 10.2.0.2 grid control
10.2.0.1 IS NOT CERTIFIED!!!!
Cheers,
Bazza

Jasper report on HTML when one image loaded from database and for the other

How to generate jasper report on HTML when one image loaded from database and for the other we give a image path
My code
ByteArrayOutputStream baos = new ByteArrayOutputStream();
          exporter = new JRHtmlExporter();
          exporter.setParameter(JRExporterParameter.JASPER_PRINT, print);
          exporter.setParameter(JRExporterParameter.OUTPUT_STREAM, baos);
          exporter.setParameter(JRHtmlExporterParameter.IMAGES_URI, strImageInputDirectory);
     exporter.setParameter(JRHtmlExporterParameter.IMAGES_DIR_NAME, strImageOutputPath == null ? "." : strImageOutputPath);
     exporter.setParameter(JRHtmlExporterParameter.IS_OUTPUT_IMAGES_TO_DIR, Boolean.TRUE);
     exporter.setParameter(JRHtmlExporterParameter.IS_USING_IMAGES_TO_ALIGN, Boolean.FALSE);
     exporter.setParameter(JRHtmlExporterParameter.IS_WHITE_PAGE_BACKGROUND, Boolean.FALSE);
          exporter.exportReport();
          byte[] bdata = ((ByteArrayOutputStream) baos).toByteArray();
Can any one help pls
Message was edited by:
ameet.au

hey sorry for posting it in this forum.
but do u have sample code for making it work.. since i am able to do it on PDF format(image from Database and another stored in the webserver) using
byte image[] =(byte[]) outData.get("image");
                    ByteArrayInputStream img = new ByteArrayInputStream(image);
                    hmimg.put("P_PARAMV3", img);
print = JasperFillManager.fillReport(reportFileName, hmimg, jrxmlds);
bdata= JasperExportManager.exportReportToPdf(print);

[SOLVED] database file for multilib does not exist

Hey guys I ran into a problem today when I tried to install the proper packages I needed to use my wifi card. However when I tried to install it it gives me the error "database file for multilib does not exist" I can t seem to find out why I even tried chrooting into it and installing it that way with no luck. The package I tried to install was "pacman -S wireless_tools netcfg" thanks for the help guys you've been great.
Last edited by bdawg (2012-09-18 22:57:17)

bdawg wrote:
Ok so the whole output is as follows:
Warning: database file for 'multilib' does not exist
Error: failed to prepare transaction (could not find database)
And my Pacman.conf is blank
pacman.conf and Pacman.conf (with capital 'P') are two different files. Double-check this.
Are you running a 64-bit system?
Your /etc/pacman.conf should look like this: https://projects.archlinux.org/pacman.g … an.conf.in but with some repositories configured: https://wiki.archlinux.org/index.php/Pa … positories
Last edited by karol (2012-09-18 22:13:59)

Creating a Database link for a user

Hello All,
I am trying to create a database link for one of my users.
When I create it as sysdba the link gets created in the SYS schema which tells me that my syntax is working/fine.
But when I ALTER my SESSION and set my CURRENT_SCHEMA = <USER_NAME> I get ORA-00990: missing or invalid privilege
So I tried granting the user CREATE DATABASE LINK, CREATE PUBLIC DATABASE LINK, and DROP PUBLIC DATABASE LINK.
Same error.
Any ideas what I am missing?
Thanks,
Craig

CraigBoyd wrote:
Hello All,
I am trying to create a database link for one of my users.
When I create it as sysdba the link gets created in the SYS schema which tells me that my syntax is working/fine.
But when I ALTER my SESSION and set my CURRENT_SCHEMA = <USER_NAME> I get ORA-00990: missing or invalid privilege
So I tried granting the user CREATE DATABASE LINK, CREATE PUBLIC DATABASE LINK, and DROP PUBLIC DATABASE LINK.
Same error.
Any ideas what I am missing?
Thanks,
Craigyou need to create a new session after the GRANT was issued.

Error while sending the mail( Database error for ADDR_PERS_COMP_COMM_GE)

Hello guys,
I am facing the error    " Database error for <ADDR_PERS_COMP_COMM_GET> <0> " as a pop-up message.
below is my program.
types: BEGIN OF t_p0002,
        pernr type PERSNO,       "Personnel number
        nachn TYPE PAD_NACHN,    "Last Name
        VORNA TYPE PAD_VORNA,    "First Name
        gbdat TYPE gbdat,        "Date of Birth
      END OF t_p0002.
*******************Data of an object which can be changed**************************************
data   S_maildata type SODOCCHGI1.
*******************Text field length 255: texts***********************************************
data : IT_MAILTXT1 type table of SOLISTI1 , "Internal table will contain texts of mail header
       WA_MAILTXT1 TYPE SOLISTI1,
       IT_MAILTXT2 type table of SOLISTI1 , "Internal table will contain texts of contents in the mail
       WA_MAILTXT2 TYPE SOLISTI1.
*******************Structure of the API Recipient List*****************************************
data : IT_MAILREC type table of SOMLRECI1,
       WA_MAILREC TYPE SOMLRECI1.
DATA : it_pa0002 TYPE TABLE OF t_p0002,
       wa_pa0002 type t_p0002.
data Header_text type c LENGTH 15.
CONSTANTS content_text type c LENGTH 35 VALUE 'Tomorrow is the birthday of'.
*******************Event start of selection***************************************************
start-of-selection.
PERFORM get_birthdate.   " will give birthday details
PERFORM document_details. " will give text and mail details
*&      Form get_birthdate
      text : subroutine to get employee birthdate details
form get_birthdate.
data : l_date like sy-datum.
refresh it_pa0002.
l_date = sy-datum + 1.
SELECT pernr nachn vorna gbdat
    from pa0002
    INTO TABLE it_pa0002
    where gbdat = '19650302'.
ENDFORM.                    "get_birthdate
*&      Form document_details
      text : subroutine to get texts and mail details.
FORM document_details.
CLEAR: Header_text,
          wa_MAILREC.
REFRESH IT_MAILREC.
S_maildata-obj_name = 'Birthday Reminder'.
s_maildata-obj_descr = 'Birthday Reminder'.
s_maildata-obj_langu = sy-langu.
READ TABLE IT_MAILTXT1 INTO WA_MAILTXT1
WITH KEY WA_MAILTXT1-line .
WA_MAILTXT1-line = 'Birthday Reminder'.
append WA_MAILTXT1 TO IT_MAILTXT1.
CLEAR WA_MAILTXT1.
LOOP at it_pa0002 INTO wa_pa0002.
    READ TABLE IT_MAILTXT2 INTO WA_MAILTXT2
     WITH KEY WA_MAILTXT2-line .
    CONCATENATE content_text ' ( ' wa_pa0002-pernr ' ) ' wa_pa0002-nachn wa_pa0002-vorna
    INTO WA_MAILTXT2 SEPARATED BY ' '.
    append WA_MAILTXT2 TO IT_MAILTXT2.
    CLEAR WA_MAILTXT2.
    CLEAR wa_pa0002.
ENDLOOP.
   LOOP AT IT_MAILREC INTO WA_MAILREC.
WA_MAILREC-RECEIVER = 'Any mail id'.
WA_MAILREC-rec_type = 'U'.
append WA_MAILREC TO IT_MAILREC.
   ENDLOOP.
********************Function Mofule:To Send new Document*****************************************
CALL FUNCTION 'SO_NEW_DOCUMENT_SEND_API1'
EXPORTING
document_data = S_maildata
DOCUMENT_TYPE = 'RAW'
PUT_IN_OUTBOX = ' '
COMMIT_WORK = 'X'
IMPORTING
SENT_TO_ALL =
NEW_OBJECT_ID =
tables
OBJECT_HEADER = IT_MAILTXT1
OBJECT_CONTENT = IT_MAILTXT2
CONTENTS_HEX =
OBJECT_PARA =
OBJECT_PARB =
receivers = IT_MAILREC
   EXCEPTIONS
   TOO_MANY_RECEIVERS = 1
   DOCUMENT_NOT_SENT = 2
   DOCUMENT_TYPE_NOT_EXIST = 3
   OPERATION_NO_AUTHORIZATION = 4
   PARAMETER_ERROR = 5
   X_ERROR = 6
   ENQUEUE_ERROR = 7
   OTHERS = 8
IF sy-subrc = 0.
    MESSAGE ID SY-MSGID TYPE SY-MSGTY NUMBER SY-MSGNO
    WITH SY-MSGV1 SY-MSGV2 SY-MSGV3 SY-MSGV4.
ENDIF.
ENDFORM.                    "document_details
After I pressed the exit button the program is getting terminated but still this mail is comming to sost transaction code.
If I will comment the message code which is after sy-subrc the popup will not come and program will work without any interruption.
Can anybody please solve this problem?

Resolved

TF244069: An error occurred while checking the provisioning status of the reporting database schema for a PWA instance.

The command TfsAdmin ProjectServer /RegisterPWA causes next error:
TF244069: An error occurred while checking the provisioning status of the reporting database schema for a PWA instance.
Project Server returned the following error: "Server was unable to process request. ---> The request failed with HTTP status 401: Unauthorized.".
(type ProvisionException)
Exception Stack Trace:    at Microsoft.TeamFoundation.Sync.Provisioning.ProvisionPwaDBSchema.HandleSoapException(SoapException soapException, String errorResourceString)
   at Microsoft.TeamFoundation.Sync.Provisioning.ProvisionPwaDBSchema.IsDBSchemaProvisioned()
   at Microsoft.TeamFoundation.Sync.Provisioning.ProvisionManager.Provision()
I installed SharePoint 2013 and Project Server 2013 as farm and TFS 2012 and my account has permissions everywhere. I read article
http://msdn.microsoft.com/en-us/library/gg412653.aspx and gave full permissions for TFS account to SQL and Project, Project app pool account to SQL, but still have an error.
How can I find out what exactly permissions are not enough???

The problem was in claims authentication. Changed to Windows and all worked out.

Creation of a database engine for mobile devices using j2me

am trying to develop a database engine for mobile devices.. it is to develop a miniature version of the DBMS that
can be deployed on a mobile phone..I have to develop my own code for performing tasks such a s creating a table,
inserting values into it, selecting from it etc..
I limited my self to develop the software so that it can perform 3 functionalities of create, insert,select..
I should be taking the details such as table name and its parameters from the user and then should be able to
create a suitable data structure for it(i tried to develop a class)...
Usage of RMS package helps me partially in this.. I did that and ll be doing that..
I got stuck while developing the code for creation of a table.. I am facing problems in creating a dynamic data
structure for a table and also to use such data structure else where in my project..
I need help in developing an algorithm for this..
I would be very grateful to u all if u help me out in developing the code for this project..

I'm sorry for the amount of time it took me to get back. Derby is an open source database written entirely in Java. I do not know if it can support resource constrained devices like MIDP compliant, but may work okay with CLDC.
But outside of Derby being a solution, let me give you a few ideas off the top of my head.
Set up a database server in a separate thread. This server will really be your controller for RMS access.
Since RMS is just a big sequential 'pipe' you will have to think of data as 'frames' - (starttable) (tableID) (tablename) (data) (tablename) (data).....(endtable).
When you need to write additional data, just append it to the end of the RMS object.
When you need to retrieve data, thing are more complex.
1. Read in all data, looking for your particular tableID. This may be made much easier using RMS filters - (I'm not sure, I've never used them)
2. Once start of table of interest is found, stick the data elements in either a java vector or array until you reach the table end identifier. I think vector will be a better choice - trust me. (I think its available in J2ME...)
3. Package this into a do while loop until the element you are searching for is read. If you need to do some sorts on the data or something else that requires the all the data to be present then you need all the data for that particular table. One thing will always be clear. The first data you grab will always be some start table identifier and the last data you grab will be an end table identifier. We just don't know which table because of how we put stuff in the RMS resource.
This provides you a few positives as well as negatives:
Positive:
1. Fast data writes, no need to search for a particular table before accessing it, nor do you need to search for an index in that table.
2. When looking for data, data may* be found without searching through the entire table. This is accomplished with RMS filters or logic test within the RMS read loop.
Negative:
1. Slow when all data of a table is needed (i.e. compute sums or averages of entries). The entire RMS database must be read to ensure all the entries are searched. An example of how this is a problem is as follows: You have 5000 entries in you RMS database resource and you are looking to compute the average of a value in some table. When you first wrote the data to the table, it was done sequentially and no other data for that table exist. But we can't tell if that's the case, so we have to read through all 5000 entries to make sure we looked for every piece of data.
Beacuse of this issue, this database structure, performance may be fine for 50K - 100K entries (depending on table element size), if the reading requirements don't force full data reads. Otherwise, 25K may be an upper limit.
I hope this helps.
Edited by: estarkey on Mar 17, 2009 9:15 PM
Edited by: estarkey on Mar 17, 2009 10:01 PM

Installation error message for Oracle Database software for version 10g

Would someone be able to advise why I keep getting the following error message whilst installing Oracle trial Database software for version 10g Release 2 Standard Edition, Standard Edition One, and Enterprise Edition? Link listed below : -
http://www.oracle.com/technology/software/products/database/oracle10g/index.html
Error message "Cannot create directory"C:\oracle\product\10.2.0\db_7\cfgtoollogs\dbca\projemp"
Below is the 12 steps that I go through, please advise what I'm doing wrong : -
1. (Operations) default is Create a database
2. (Database templetes) default is general purpose
3. (Database Identification) projemp.local for Global database name & projemp for SID
4. (Management options) default is "Configure the database with Enterprise manager, also the options button has been clicked for "Use database control for database management"
5. (Database Credentials) the options button has been clicked for "Use the same password for all accounts" so I've set up a new password, was that correct?
6. (Storage options) the options button is clicked for "File System - use the file system for database storage.
7. (Database file locations) the options button is clicked for "Use database file locations for template" Is this option correct? Other options are Use common location for all database files or use Oracle-managed files?
8. (Recovery configuration) the options button is clicked for "Specify flash recovery area
9. (Database content) nothing has been selected, the only option is "Sample schemas" should that be clicked?
10. (Initialization parameters) the options button is clicked for "Typical- allocate memory as a % of the total physical memory
11. (Database storage) no options available
12. (Creation options) the options button has been selected for "Create Database"
Click finish
I then get a screen stating General purpose, click OK then I get the following error message as stated at the start of this e-mail ""Cannot create directory"C:\oracle\product\10.2.0\db_7\cfgtoollogs\dbca\projemp".
Regards
Phil

855880 wrote:
I have been trying to install the "Oracle Database software for version 10g Release 2 Standard Edition, Standard Edition One, and Enterprise Edition" about six times with no success.Do you realize you just mentioned 3 different and distinct products? So which one are you installing?
>
I've gone through my courses instructions as listed above (1-12) and end up with the following error message"C:\oracle\product\10.2.0\db_7\cfgtoollogs\dbca\projemp".What course?
>
I've removed the software from my computer using control panel, programs & features then uninstall once but the other five times the software hasn't been listed. Whilst the Oracle was on my task bar I was able to install using Start > Programs > Oracle - HOME-NAME > Database Administration > Database Configuration Assistant.No you didn't. Database Configuration Assistant does not remove software. It can remove a database. As I mentioned before, there is a difference between the software and the objects that software manages. Deleting an Excel spreadsheet is not the same as deleting Microsoft Office. Deleting an Oracle database with Database configuration assistant is not the same as removing the Oracle software.
>
Now that oracle is not on my task bar I've unzipped the link below, clicked on db, Disk1, setup, changed the Database password (is that correct?) install and I get the following error message "Check complete. The overall result of this check is: Failed<<<<<
Problem: The install has detected that the primary IP address of the system is DHCP-assigned.
Recommendation: Oracle supports installations on systems with DHCP-assigned IP addresses;
However, before you can do this, you must configure the Microsoft LoopBack Adaptor to be the primary network adapter on the system. See the installation Guide for more details on installing the software on systems configured with DHCP."
So what did you do with the above error message? Did you follow up on what it said? Did you read the very fine Installation Guide that comes with the software? Did you read the section on networking considerations where it discussed DHCP assigned addresses and installing the loopback adapter?
http://www.oracle.com/technology/software/products/database/oracle10g/index.html
Ok, that link takes us to the download page, which does not shed any light at all on your problems
I'm using Windows Vista Home Premium, 32 bit operating system, and my computer is saying I have 142 GB free space.
If you read the installation manual that came with the downloaded software, you'd have seen in the prerequisites that Home editions of Windows are NOT listed as supported platforms, whereas Business, Enterprise, and Ultimate editions specifically ARE listed as supportd.
Hope this is some help.And
I'm not to clever on computers so would you be able to advise how I get to the command window to issue the SET command please?
Also I've no idea what OS user I am, I'm taking an on-line Oracle course and been advised to install "Oracle Database software for version 10g Release 2 Standard Edition, Standard Edition One, and Enterprise Edition"
How do I find out if I'm part of an Administrator, ORA_DBA group ?
Can you walk me through how to create the directory from command line please?Ok, given the above statements from you, I'm not even sure where to begin. I don't want to be cruel, but this self-admitted lack of even the most rudimentary knowledge by someone attempting to learn about Oracle is truly astounding. What course are you taking? Why are you taking this course?

Problem with "Database Gateway for SQL Server"

Hello,
i am testing the different technologies for connecting an oracle database with a sql-server database.
The way using 10g-generic-connectivity with ODBC works fine, but the 11g-DG4MSQL makes problems.
Environment:
Server PEGASUS (32bit Windows Server 2003 R2 SP2) with Oracle Database 10g Release 10.2.0.4.0
Server OBELIXUS (32bit Windows 2000 Sp4) with MS-SQL-Server 2005
On PEGASUS i have installed the gateway in a new oracle home directory:
"D:\oracle\product\10.2.0\db_1" => home directory of 10g
"D:\oracle\product\11.1.0\tg_1\" => home directory of the gateway
D:\oracle\product\10.2.0\db_1\NETWORK\ADMIN\tnsnames.ora:
MSSQLDG =
(DESCRIPTION =
(ADDRESS_LIST =
(ADDRESS = (PROTOCOL = TCP)(HOST = PEGASUS)(PORT = 1521))
(CONNECT_DATA =
(SERVICE_NAME = DG4MSQL)
(HS = OK)
MSSQL =
(DESCRIPTION =
(ADDRESS_LIST =
(ADDRESS = (PROTOCOL = TCP)(HOST = PEGASUS)(PORT = 1521))
(CONNECT_DATA =
(SERVICE_NAME = MSSQLTEST)
(HS = OK)
D:\oracle\product\10.2.0\db_1\NETWORK\ADMIN\listener.ora:
SID_LIST_LISTENER =
(SID_LIST =
(SID_DESC =
(SID_NAME = PLSExtProc)
(ORACLE_HOME = D:\oracle\product\10.2.0\db_1)
(PROGRAM = extproc)
(SID_DESC =
(GLOBAL_DBNAME = INTEGRAT)
(ORACLE_HOME = D:\oracle\product\10.2.0\db_1)
(SID_NAME = INTEGRAT)
(SID_DESC =
(SID_NAME = MSSQLTEST)
(PROGRAM = D:\oracle\product\10.2.0\db_1\bin\hsodbc)
(ORACLE_HOME = D:\oracle\product\10.2.0\db_1)
(SID_DESC=
(SID_NAME=DG4MSQL)
(ORACLE_HOME=D:\oracle\product\11.1.0\tg_1)
(PROGRAM=D:\oracle\product\11.1.0\tg_1\BIN\dg4msql)
LISTENER =
(DESCRIPTION_LIST =
(DESCRIPTION =
(ADDRESS = (PROTOCOL = IPC)(KEY = EXTPROC1))
(ADDRESS = (PROTOCOL = TCP)(HOST = pegasus.cursor.de)(PORT = 1521))
D:\oracle\product\11.1.0\tg_1\dg4msql\admin\initDG4MSQL.ora:
HS_FDS_CONNECT_INFO=OBELIXUS/MSSQLSERVER/testuju
HS_FDS_TRACE_LEVEL=DEBUG
HS_FDS_RECOVERY_ACCOUNT=RECOVER
HS_FDS_RECOVERY_PWD=RECOVER
D:\oracle\product\10.2.0\db_1\hs\admin\initMSSQLTEST.ora:
HS_FDS_CONNECT_INFO=DSN_MSSQL
HS_FDS_TRACE_LEVEL=OFF
HS_LANGUAGE=AMERICAN_AMERICA.WE8MSWIN1252
HS_FDS_FETCH_ROWS=100
HS_RPC_FETCH_REBLOCKING=OFF
How mentioned above, the access from oracle to sqlserver using MSSQL(10g hsodbc.exe) works fine.
But when trying to acces the sqlserver using MSSQLDG (11g dg4msql.exe) I get the following error:
ORA-28500: Verbindung von ORACLE zu Fremdsystem gab diese Nachricht zurück:
[Oracle][ODBC SQL Server Driver][DBNETLIB]Ungültige Verbindung.
[Oracle][ODBC SQL Server Driver][DBNETLIB]ConnectionOpen (ParseConnectParams()).
[Oracle][ODBC SQL Server Driver]Ungültiges Attribut für die Verbindungszeichenfolge
ORA-02063: vorherige 2 lines von DBL_MSSQL4
Here the contect of the file "DG4MSQL_agt_2332.trc":
Oracle Corporation --- FREITAG AUG 22 2008 16:17:42.198
Heterogeneous Agent Release
11.1.0.6.0
Oracle Corporation --- FREITAG AUG 22 2008 16:17:42.198
Version 11.1.0.6.0
Entered hgogprd
HOSGIP for "HS_FDS_TRACE_LEVEL" returned "DEBUG"
Entered hgosdip
setting HS_OPEN_CURSORS to default of 50
HOSGIP returned value of "RECOVER" for HS_FDS_RECOVERY_ACCOUNT
HOSGIP returned a value for HS_FDS_RECOVERY_PWD
setting HS_FDS_TRANSACTION_LOG to default of "HS_TRANSACTION_LOG"
setting HS_FDS_TRANSACTION_ISOLATION to default of "READ_COMMITTED"
setting HS_NLS_NCHAR to default of "AL16UTF16"
setting HS_FDS_TIMESTAMP_AS_DATE to default of "TRUE"
setting HS_RPC_FETCH_REBLOCKING to default of "ON"
setting HS_FDS_FETCH_ROWS to default of "100"
setting HS_FDS_RESULTSET_SUPPORT to default of "FALSE"
setting HS_FDS_PROC_IS_FUNC to default of "FALSE"
setting HS_FDS_CHARACTER_SEMANTICS to default of "FALSE"
setting HS_FDS_MAP_NCHAR to default of "TRUE"
setting HS_NLS_DATE_FORMAT to default of "YYYY-MM-DD HH24:MI:SS"
setting HS_FDS_REPORT_REAL_AS_DOUBLE to default of "FALSE"
setting HS_LONG_PIECE_TRANSFER_SIZE to default of "65536"
setting HS_SQL_HANDLE_STMT_REUSE to default of "FALSE"
setting HS_FDS_QUERY_DRIVER to default of "FALSE"
setting HS_CALL_NAME_ISP to "gtw$:SQLTables;gtw$:SQLColumns;gtw$:SQLPrimaryKeys;gtw$:SQLForeignKeys;gtw$:SQLProcedures;gtw$:SQLStatistics"
Exiting hgosdip, rc=0
ORACLE_SID is "DG4MSQL"
Product-Info:
Port Rls/Upd:6/0 PrdStat:0
Agent:Oracle Database Gateway for MSSQL
Facility:hsa
Class:MSSQL, ClassVsn:11.1.0.6.0_0006, Instance:DG4MSQL
Exiting hgogprd, rc=0
Entered hgoinit
HOCXU_COMP_CSET=1
HOCXU_DRV_CSET=178
HOCXU_DRV_NCHAR=2000
HOCXU_DB_CSET=178
HOCXU_SEM_VER=102000
Entered hgolofn at 2008/08/22-16:17:42
RC=-1 from HOSGIP for "PATH"
PATH from environment is "d:\oracle\product\11.1.0\tg_1\bin;D:\oracle\product\10.2.0\db_1\bin;C:\WINDOWS\system32;C:\WINDOWS;C:\WINDOWS\System32\Wbem;C:\Programme\IBM\Informix\Client-SDK\bin"
Exiting hgolofn, rc=0 at 2008/08/22-16:17:43
HOSGIP for "HS_OPEN_CURSORS" returned "50"
HOSGIP for "HS_FDS_FETCH_ROWS" returned "100"
HOSGIP for "HS_LONG_PIECE_TRANSFER_SIZE" returned "65536"
HOSGIP for "HS_NLS_NUMERIC_CHARACTER" returned ".,"
Exiting hgoinit, rc=0 at 2008/08/22-16:17:43
Entered hgolgon at 2008/08/22-16:17:43
reco:0, name:testuju, tflag:0
Entered hgosuec at 2008/08/22-16:17:43
uencoding=UTF16
Entered shgosuec at 2008/08/22-16:17:43
Exiting shgosuec, rc=0 at 2008/08/22-16:17:43
shgosuec() returned rc=0
Exiting hgosuec, rc=0 at 2008/08/22-16:17:43
HOSGIP for "HS_FDS_RECOVERY_ACCOUNT" returned "RECOVER"
HOSGIP for "HS_FDS_TRANSACTION_LOG" returned ""HS_TRANSACTION_LOG""
HOSGIP for "HS_FDS_TIMESTAMP_AS_DATE" returned "TRUE"
HOSGIP for "HS_FDS_CHARACTER_SEMANTICS" returned "FALSE"
HOSGIP for "HS_FDS_MAP_NCHAR" returned "TRUE"
HOSGIP for "HS_FDS_RESULT_SET_SUPPORT" returned "FALSE"
HOSGIP for "HS_FDS_PROC_IS_FUNC" returned "FALSE"
HOSGIP for "HS_FDS_REPORT_REAL_AS_DOUBLE" returned "FALSE"
using testuju as default value for "HS_FDS_DEFAULT_OWNER"
HOSGIP for "HS_SQL_HANDLE_STMT_REUSE" returned "FALSE"
Entered hgocont at 2008/08/22-16:17:43
HS_FDS_CONNECT_INFO = "OBELIXUS/MSSQLSERVER/testuju"
RC=-1 from HOSGIP for "HS_FDS_CONNECT_STRING"
Entered hgogenconstr at 2008/08/22-16:17:43
dsn:OBELIXUS/MSSQLSERVER/testuju, name:testuju
optn:
Entered shgogohn at 2008/08/22-16:17:43
ohn is 'OraGtw11g_home1'
Exiting shgogohn, rc=0 at 2008/08/22-16:17:43
Entered hgocont_OracleCsidToIANA at 2008/08/22-16:17:43
Returning 2252
Exiting hgocont_OracleCsidToIANA at 2008/08/22-16:17:43
##>Connect Parameters (len=223)<##
## DRIVER=Oracle 11g dg4msql-OraGtw11g_home1;
## SERVER=OBELIXUS\MSSQLSERVER;
## Database=testuju;
#! UID=testuju;
#! PWD=*
## AnsiNPW=Yes;
## QuotedId=Yes;
## IANAAppCodePage=2252;
## ArraySize=100;
## PadVarbinary=0;
## SupportNumericPrecisionGreaterThan38=1;
Exiting hgogenconstr, rc=0 at 2008/08/22-16:17:44
Entered hgopoer at 2008/08/22-16:18:00
hgopoer, line 159: got native error 14 and sqlstate 08001; message follows...
[Oracle][ODBC SQL Server Driver][DBNETLIB]Ungültige Verbindung.[Oracle][ODBC SQL Server Driver][DBNETLIB]ConnectionOpen (ParseConnectParams()).[Oracle][ODBC SQL Server Driver]Ungültiges Attribut für die Verbindungszeichenfolge
Exiting hgopoer, rc=0 at 2008/08/22-16:18:00
hgocont, line 1890: calling SqlDriverConnect got sqlstate 08001
Exiting hgocont, rc=28500 at 2008/08/22-16:18:00 with error ptr FILE:hgocont.c LINE:1910 ID:Something other than invalid authorization
Exiting hgolgon, rc=28500 at 2008/08/22-16:18:00 with error ptr FILE:hgolgon.c LINE:612 ID:Calling hgocont
Entered hgoexit at 2008/08/22-16:18:00
Exiting hgoexit, rc=0 at 2008/08/22-16:18:00
Many thanks in advance for any help!
Regards Hartmut

At first your configuration is not really correct.
=====================================================
In the LISTENER.ORA from 10g, you must only refer to the database and hsodbc 10g
D:\oracle\product\10.2.0\db_1\NETWORK\ADMIN\listener.ora:
SID_LIST_LISTENER =
(SID_LIST =
(SID_DESC =
(SID_NAME = PLSExtProc)
(ORACLE_HOME = D:\oracle\product\10.2.0\db_1)
(PROGRAM = extproc)
(SID_DESC =
(GLOBAL_DBNAME = INTEGRAT)
(ORACLE_HOME = D:\oracle\product\10.2.0\db_1)
(SID_NAME = INTEGRAT)
(SID_DESC =
(SID_NAME = MSSQLTEST)
(PROGRAM = D:\oracle\product\10.2.0\db_1\bin\hsodbc)
(ORACLE_HOME = D:\oracle\product\10.2.0\db_1)
LISTENER =
(DESCRIPTION_LIST =
(DESCRIPTION =
(ADDRESS = (PROTOCOL = IPC)(KEY = EXTPROC1))
(ADDRESS = (PROTOCOL = TCP)(HOST = pegasus.cursor.de)(PORT = 1521))
===========================================================
Then you have to create a new listener (new name) in the gateway oracle_home on a different port than instance database:
D:\oracle\product\11.1.0\tg_1\network\admin\listener.ora
SID_LIST_LISTENERGTW =
(SID_LIST =
(SID_DESC=
(SID_NAME=DG4MSQL)
(ORACLE_HOME=D:\oracle\product\11.1.0\tg_1)
(PROGRAM=D:\oracle\product\11.1.0\tg_1\BIN\dg4msql)
LISTENERGTW=
(DESCRIPTION_LIST =
(DESCRIPTION =
(ADDRESS = (PROTOCOL = TCP)(HOST = pegasus.cursor.de)(PORT = 1522))
To start it, use the command below:
D:\oracle\product\11.1.0\tg_1\bin\LSNRCTL start listenergtw
===========================================================
D:\oracle\product\10.2.0\db_1\NETWORK\ADMIN\tnsnames.ora:
match the DG4MSQL with the listener on 1522 port
HSODBC match with binary10g on listener 1521 port
MSSQLDG =
(DESCRIPTION =
(ADDRESS = (PROTOCOL = TCP)(HOST = PEGASUS)(PORT = 1522))
(CONNECT_DATA =(SERVICE_NAME = DG4MSQL))
(HS = OK)
MSSQL =
(DESCRIPTION =
(ADDRESS = (PROTOCOL = TCP)(HOST = PEGASUS)(PORT = 1521))
(CONNECT_DATA =(SERVICE_NAME = MSSQLTEST))
(HS = OK)
Try to configure and let me know your feedback
regards,
Mireille

Multiple database instance for one user in Oracle XE

Hello,
I would like to know if there is a way to create more than one database/schema for the same user in Oracle XE.
Thanks.

And i say...
yes, indeed.. you can find out some info here..
http://www.oracle.com/technology/pub/articles/cunningham-database-xe.html

Is 10.1.0.7 database certified for OIM 9.1.0.1?

Similar Messages

Maybe you are looking for