Is Airport Extreme a router?

I recently got a brand new MacBook (running 10.5.2) and being new to the world of wireless internet connection, automatically assumed that the airport card and software in the laptop was a router as well. Is this true or do I have to purchase an Airport base? This assumption was somewhat verified when I turned the computer on and had internet access via NETGEAR. Last week I lost internet access. I then discovered that the NETGEAR access now requires a password. So as time permits, would you Mac experts educate my ignorance and tell me what I have to do to get wireless internet access with my laptop? I can only assume since I lost it, I was actually getting a feed off of my neighbor and either my neighbor or NETGEAR decided to make it unaccessible. Is this true?

The base stations are routers, but the cards aren't. You need to connect to a wireless router or wireless cable modem. You were using your neighbor's router before the neighbor set it to require a password.
(32385)

Similar Messages

HT4628 I recently transferred my internet service to another state. Have not yet moved my imac, just my pc laptop. I cannot get my airport extreme wireless router to work. The green light stays lit when everything is connected but I can't connect to the i

I recently transferred my internet service to another state.I have not yet moved my imac, just my pc laptop. I cannot get my airport extreme wireless router to work. The green light stays lit when everything is connected but I can't connect to the internet. Any suggestions?

I would recommend that you do the following as a minimum:
Power-down the modem, AirPort base station, and computer(s).
Power-up the modem; wait at least 10-15 minutes to allow it adequate time to initialize.
Power-up the AirPort base station; wait at least 5-10 minutes. Note: The AirPort's status light may continue to flash amber after it has intialized. That is because, there may be some additional configuration items necessary, like setting up wireless security, before the overall setup is completed to get a green status.
Power-up your computer(s).
If the above steps do not solve the problem, start over with step 1 above, but then perform the next steps between steps 1 & 2. above.
Disconnect the AirPort base station from the Internet broadband modem.
While all of the devices are powered-down, perform a "factory default" reset on the base station. This will get it back to its "out-of-the-box" configuration and make setting it up much easier, especially if you use the "Assist me" process within the AirPort Utility. (ref: Resetting an AirPort Base Station or Time Capsule)
After the base station resets, go ahead and power it back down.
Reconnect the AirPort base station to the Internet broadband modem. For the Extreme and Time Capsule, be sure to connect the cable to the base station's WAN (circle-of-dots) port.
Continue with step 2 in the first set of steps.
In this basic configuration, the AirPort base station will broadcast an unsecured wireless network with a Network Name (SSID) of Apple Network NNNNNN. Network clients, connected to the base station either by wire or wireless, should now be able to access the Internet through the ISP's modem. Once Internet connectivity has been verified, you can use the AirPort Utility to configure the base station for wireless security and any other desired options. Please post back your results.

Trying to clarify what these are: is airport extreme a router? What is airport express?

Trying to clarify what these are: is airport extreme a router? What is airport express a router as well?

SimonJester753 wrote:
It was a long time ago. I remember wanting to connect my desktop mac via an ethernet cable, but the setup assistant was insisting on wireless. I think I finally took out the wireless card from my Mac so it would use the ethernet cable. Eventually I put the card back.
The zillion and one setting to wade through might mean more choices to the tech-heads, but I just wanted it to work.
I don't recall the type of router we had at my previous job, but I just plugged it in, went through a simple set up and forgot about it because it just sat there and worked.
I have had to go back to factory settings and start from scratch with my Extreme many times. The last time the amber light started blinking I just ignored it for months, because it didn't effect my internet connection, I just lost the ability to get iTunes over to the Express I have hooked up to my stereo.
BTW, what's a wall wart?
The big box on the cord.

I have an Airport Extreme wireless router & I can not connect my Kindle.

I have an Airport Extreme wireless router & I can not connect my Kindle. Also, my password will not work when a visitor uses it for a laptop (even a Mac) or any other device that uses the internet. It says the password is incorrect. I easily connected a Kindle last year, but I got a new one & now I can not connect wirelessly. I see no tab to create a guest network. I do not mind giving my password to visitors, but that does not work.

If you temporarily disable wireless encryption on your 802.11n AirPort Extreme Base Station (AEBSn), can the Kindle connect to the router and gain access to the Internet now? If so, then I would suggest that you reconfigure the AEBSn to use "WPA2 Personal" for the Wireless Security setting, and then, try connecting with the Kindle again.
As far as establishing a Guest Network, the AEBSn must not be in bridge mode. That is, it should be the only router in your current network and directly conncted to the Internet modem. If it is, then you would find the Guest Networking option on the AirPort > Guest Networking tab:

Time capsule with a airport extreme n router

Question I already have a Airport Extreme N Router and it works very well. But now I would like to have the Time Capsule and some how I don't know, have both hooked up maybe the older extreme N router as a extender? Can any one tell me how I can do this or if it can even be done.

Do exactly what you describe but place the secondary router in bridge mode then configure its wireless.

Airport extreme, dlink router, no network detected

Hi
I have installed my airport extreme card, intending to connect via my D-Link DSL-G604 ADLS router to the internet, wirelessly, but airport does not detect any networks. This seems unusual as the other computer, a PC, in our house picks it up immediately, and connects.
Is there some secret to connecting to a non-airport base station? Can someone perhaps talk me through the process?
many thanks

Hi,
The D-Link I have is a little bit different than yours; mine is a DI-524. But maybe that what I read on the D-Link website will also apply to you.
D-Link recommed to set the security to WEP 128bits HEX. Try this setting. I got issue in between Airport and D-Link when I set the security to anything else but in WEP-128bits HEX as recommended on the D-Link web site.
let me know if this work!

Airport Extreme ethernet routing in Bridge Mode

i had(!) the following scenario Airport Extreme (5th Generation) .. via WAN connect to the modem, Ethernet to serval switches, WiFi acting as WDS Main
the WDS Slaves are 3 small Airport express and one Airport Extreme (1st Generation)
due a cabeling problem i had to move the WAN Modem .. and connected it to the 1st generation airport extreme created a Joined network (not WDS) enabled DHCP on the same device.
the new Airport extreme (5th generation) and the Airport Express joined the same network and running in bridge mode.
everything works just like before .. all networks parts can connect to each other, anywhere else including the internet.
exept of anything connected to the ethernet ports of the (now slaved) airport extreme (5th generation) anything connected there seems not to be routed at all ..
they have a physical connection (link show on the Airport and on the Switch. but there is zero data going trough ... no DHCP adresses assigned. manually assign a IP in the same network results in the same effect (can't even ping the directly connected Airport Extreme.
is this a Bug ?

oh ic ... thats why it worked before the other way arround ...
well does still not make any sense to me .. but you are 100% right ..
enabeling WDS on the Airport Extreme (1gen) and doing slave the Airport extreme (5 gen) works fine .. but the connection times are about 10 times slower than in a joined network.
which makes the whole show extremly slow ...
it takes some times 5 minutes and a million time clicking (assign new) to just get an IP adress ... even if the dhcp running on the same Airport where the client is connecting to ..
if the 5gen APE is WDS master .. and the 1gen is WDS Slave (my old setup) .. this problem is not existing ...
but then ican't connect the WAN modem to the slaved Airport since the slave is always bridged and the master requires internet connectivity trough the local Wan port
any idea to get arround this ?

Airport Extreme / Netgear router

Please could somebody walk me through this step by step as I am pulling my hair out ...
I have a Netgear DG834 router which is connected to my broadband connection and is feeding my Macs. I have bought an iPad2 and have been trying to connect my Airport Extreme to the Netgear in order to use WiFi. I want to leave the Netgear connected as it is because it is fast and very reliable, the Airport Extreme will be solely for iPad2 and iPhone.
I have plugged the Airport Extreme into one of the outputs from the Netgear but all I am getting is a flashing amber light. Having reset it about 20 times this afternoon I need somebody to walk me through the entire process. It keeps telling me that I don't have a WiFi connection and to be honest I have absolutely no idea how to set one up.
All help greatfully appreciated!
Chris Blackwell

i have a probleme to with my net gear dg834 and l'airport extreme, i want to use my airport extreme as WIFI and for thats i need to put my netgear only as router not wifi the only option i can use is the airport as bridge but not as WIFI...i try to cut the DHCP in the netgear but the airport dont send any signal after thats...
the question is: how i can deconnect the wireless option in my netgear and after use the airport as WIFI router.
thank (sorry my english is not good)

Airport Extreme, Linksys Router WRT54G: Internet is Impossibly Slow

I have a problem regarding wireless internet activity on my Powerbook G4. In my house, I have a Linksys Router (WRT54G) that has worked fine for other laptops (including an iBook running Airport Extreme, a Powerbook G4 running Airport, and an iMac running Airport) for many years. When I got a refurbished Powerbook G4 1.67 GHz with Airport Extreme, I found that while Airport could be configured to recognize the wireless network (with a WEP 40/128-bit encrypted key), it barely works on the computer. The signal strength is strong (the laptop is hooked up right above the Linksys router), but the Internet barely works at all. Surfing to webpages takes 10-20-30 sec to work, and often the connection seems to drop off all together. Something is clearly wrong because despite the fact that this is my fastest computer with the fastest wireless capability, it runs at a slower pace than any computer I have ever used on the web.
I was wondering if anyone has had similar problems with getting Wireless Extreme on Powerbook G4s to work with this particular (and older) model of Linksys wireless browser (WRT54G). Some Internet sleuthing led me to believe that perhaps the router firmware needs to be updated or something like that, but I haven't really found any definitive answers. If there is anything wrong on the laptop-OS-side, I have no idea. I would appreciate any pointers that you can provide!
Thank you to all,
Matthew
Computer:
Powerbook G4
1.67 GHz
1 GB DDR SDRAM
OS 10.4.8
Wireless Router:
Linksys
Model: WRT54G
Powerbook G4 Mac OS X (10.4.8) 1.67GHz, 1GB DDR SDRAM

Hi all,
Thank you for your help. Unfortunately, my problems persist.
I was able to reset my router and to configure it again on the web-based router configuration.
As per your suggestion, I tried switching the Wireless Network Mode to "G-only." Not only did this kick off my older computers on the network (an old iMac and an older Powerbook G4, both with normal airport), but it did not fix the speed problems on the new Powerbook G4/with Airport Extreme. I am back on the mixed setting now in order to get most of the computers on the network back to their old working states...
I also tried disabling my WEP encrypted key but found that this did not speed anything up at all.
I have upgraded my firmware from its previous version, v 1.41.2 (very old!), to the latest from the Linksys website: v 4.30.5. This has not helped at all either.
Is it possible that there is any setting on the Powerbook/Airport Extreme itself that is causing these problems?
Thank you all again for your help,
Matthew
Powerbook G4 Titanium Mac OS X (10.4.7) 1gHz, 512mb RAM

Is current airport extreme a router?

My airport isnt - I had to use old router conected to it.
I may be getting the words wrong, but bacically I got a netgear wireless router in 2001. Bought airport extreme 2 yrs ago to replace it, but of course it doesn't as its not actually a thing that turns the phone line into and internet signal. Modem? Router? whatever its cammed.
The netgear station keeps quitting, but I have no idea what to replace it with - any ideas?
I want fast broadband!!

It's a router, but it needs to be connected to a modem

Mac OSX server not supported behind Airport Extreme NAT router?!!

For a customer, I recently installed a new XServe, within a local network with an Airport Extreme (n) with FW 7.4.2. Mac OSX Server manages the router (which has a fixed IP from the ISP). Because the Mac OSX Server runs a DNS server (supporting a local domain), OSX Server reconfigured the Airport Extreme, so that it would forward DNS queries to the server. The server's dns server will forward queries for non-local domains to the ISP's dns servers.
All clients get their IP configuration using DHCP from the router. You can't use the DHCP service of the server, as you can't disable DHCP on the router (in NAT mode).
All clients get the router's IP as the dns server.
HOWEVER:
The Airport Extreme can't connect to the internal DNS server! *It doesn't seem to be able to route dns requests to the internal network* (verified using nslookup). Any dns queries sent to the router will time out.
Come on, Airport Extreme team.. you can't claim the Airport Extreme to be the ideal router in combination with an OSX server, if this simple and very common setup is not supported! How hard can it be to either:
...*Allow us to disable DHCP on the router* (even when in NAT mode), so we can use the OSX server for this (which will dispatch the correct DNS settings)
...*Allow the router to route DNS queries to the local DNS* (OSX) server (which should be working anyway)
Message was edited by: blackbit

blackbit, Welcome to the discussion area!
It doesn't seem to be able to route dns requests to the internal network (verified using nslookup).
That is true.
This is a user to user discussion area so Apple will not see your suggestions here. Instead go to www.apple.com/feedback/airportextreme.html and send them to Apple.

How large of an Ethernet Switch can you add to an Airport Extreme gigabit router?

I have a gigabit Airport Extreme router. I like using the Airport Utility to control my network. I want to convert a large number of wireless connections to wired ethernet devices, about 24. The reason is that I just get too many wireless dropouts, and I need a more reliable network. I am looking for the best way to design this. It seems like adding a gigabit Ethernet switch is the easiset and best way to accomplish this. My questions are:
1. How large of a gigabit switch can you add to the LAN port of an Airport Extreme: 24-port, 48-port?
2. How far down can you cascade switches? In other words, can I connect three 5-port switches (level 1 switches) to the three LAN ports on the Airport Extreme, and then connect more 5-port switches to the level 1 switches?
3. What are the performance implications for either design. Can you achieve gigabit performance with these designs?
Thanks for the help.

I have a network with an Extreme base station, 3 Extreme wired extenders and 1 express wired extender - in the mix are four 24 port gigabit switches and two 8 port gigabit switches - so you can add as much as you want within the limits of the internal IP address range which is controling the number of devices on the network.

How to set up Airport Extreme wireless router

Hello. I am trying to connect my Airport Extreme base station to my phone line connection.
From the phone line there is an ADSL filter which has a RJ11 output and phone modem. I purchased a RJ11 to RJ45 (Ethernet) and tried to plug into my router. The airport extreme doesn't recognise anything being plugged in!
My ISP is TalkTalk. This is a secondary router. Other one is a Netgear using downstairs phone modem.
Any help would be grately appreciated
Sam

Thanks for your answer.
So if i buy a DSL modem and go Phone line > DSL modem > Airport Extreme > Mac / WiFi - will that work?
Do you recommend any specific DSL modems that dont use USB (or USB...)?
Thanks

AirPort Extreme AC router hard drive access SLOW

Just bought a new AC AirPort Extreme router. I can stream 1080p movies from the Internet no problem, but read/write/delete from hard drive attached to the AirPort is SLOW.
45min to delete 4 files. (this is ridiculous)
up to five min to see contents of clicked folder. (sometimes it never shows you the contents)
from the same MBPro I can get 20Mbps downloads on the Internet, not a network issue.
I see the same slowness on a windows 7 machine connected to the AEP on a gigabit LAN connection.
On occasion the AEP just gives up and reboots while trying to accessing a hard drive. Otherwise rock solid performance.
I have 2 self powered USB HDD's (Western Digital, Toshiba) attached via powered USB hub (Belkin).
Hardware specs:
2010 MBP - CPU i7 2.66GHz - 8GB Ram - OS X 10.8.5
2013 AEP version 7.7.1
Toshiba USB HDD 750 GB (Mac OS Extended (Journaled))
Western Digital USB HDD 1 TB (Mac OS Extended (Journaled))
Why would it be so slow? (oddly, removing the Toshiba drive helps, but a little)

Please check out the following AirPort User Tip about what you can expect for storage throughput performance on the AirPort routers. Although this was written for the 802.11n models, it hold reasonablly well for the newest 802.11ac a well.
Another source is SmallNetBuilder. They recently tested storage performance on the 802.11ac Extreme and found it less than stellar (around 2.4 MBps) for Windows clients.

HH3 Airport Extreme DNS / router address issues

I have a HH3 hard wired (ethernet) from HH port 1 to the small circle port on the Airport Extreme. The AE extends the network around the house via Airport express and we have done this by creating a new network so we can connect either to the HH or to the AEBS network. The AEBS is set to bridge mode but wrong DNS and router addresses are given out by both HH and AEBS when the AE is turned on (192.1.68.1.2 instead of 192.168.1.254). We can bypass the issue by setting these manually but would prefer not to have to. If I turn the AE off, the HH issues the correct DNS and router addresses. I am asking the same question on the Apple forums but not everyone there is familiar with the HH.

Bizarrely, having tried every configuration on the AE, reminded of something vofsanity said to me in a previous thread, I unplugged a powerline extender and the problem seems to have fixed itself!

Is Airport Extreme a router?

Similar Messages

Maybe you are looking for