Is anybody experiencing rapid % drop in use but not standby?

I'm experiencing 1-2% battery drop every 3-4 minutes while surfing/wifi and social media apps (facebook/twitter) or 1% every 5 minutes on phonecalls but +no % drop+ on standby so I am wondering - is this normal? iOS 4.0.1
Thanks!

I wouldn't worry too much about the rate the battery guage drops, I'd just look at your usage stats at the end of a 100% - 0% session. Apple say you can get 10 hours of browsing on wifi under optimal conditions.
So if we say subtract an hour just to be realistic, then a further hour because it's unlikely you will have a 100% signal and you may have push etc enabled, that's 8 hours. 480 minutes. So you should be seeing a drop of 1% approx every 4.8 minutes. Bear in mind that this is all just hard calculations, and there can obviously be a lot of variance where battery chemistry is concerned, but it should give you a ball park.
So based on that, maybe it's dropping a little quicker than expected, but as I said at the start of the post, I'd be more concerned with the usage counter at the end of a full battery run than the guage while using.

Similar Messages

  • BPEL SCA: XML-20129: (Error) Namespace prefix 'ui' used but not declared.

    SOASuite 11g
    Oracle Weblogic Server 10.3.3
    Oracle Solaris on SPARC (64-bit) 10
    Database: Oracle Server - Enterprise Edition 10.2.0.5
    When I start the SOA domain server, I find the following in the log file:
    <Feb 25, 2011 10:41:23 AM CET> <Error> <org.apache.commons.digester.Digester> <BEA-000000> <Parse Error at line 9 column 79: <Line 9,
    Column 79>: XML-20129: (Error) Namespace prefix 'ui' used but not declared.
    org.xml.sax.SAXParseException: <Line 9, Column 79>: XML-20129: (Error) Namespace prefix 'ui' used but not declared.
    at oracle.xml.parser.v2.XMLError.flushErrorHandler(XMLError.java:422)
    at oracle.xml.parser.v2.XMLError.flushErrors1(XMLError.java:287)
    at oracle.xml.parser.v2.NonValidatingParser.parseDocument(NonValidatingParser.java:342)
    at oracle.xml.parser.v2.XMLParser.parse(XMLParser.java:226)
    at org.apache.commons.digester.Digester.parse(Digester.java:1785)
    at oracle.fabric.composite.Parser.parseComposite(Parser.java:132)
    at oracle.integration.platform.kernel.WLSFabricKernelInitializer.deployComposite(WLSFabricKernelInitializer.java:493)
    at oracle.integration.platform.kernel.WLSFabricKernelInitializer.prepareCompositeDeployments(WLSFabricKernelInitializer.java:
    239)
    at oracle.integration.platform.kernel.WLSFabricKernelInitializer.init(WLSFabricKernelInitializer.java:127)
    at javax.servlet.GenericServlet.init(GenericServlet.java:241)
    at weblogic.servlet.internal.StubSecurityHelper$ServletInitAction.run(StubSecurityHelper.java:283)
    at weblogic.security.acl.internal.AuthenticatedSubject.doAs(AuthenticatedSubject.java:321)
    at weblogic.security.service.SecurityManager.runAs(SecurityManager.java:121)
    at weblogic.servlet.internal.StubSecurityHelper.createServlet(StubSecurityHelper.java:64)
    at weblogic.servlet.internal.StubLifecycleHelper.createOneInstance(StubLifecycleHelper.java:58)
    at weblogic.servlet.internal.StubLifecycleHelper.<init>(StubLifecycleHelper.java:48)
    at weblogic.servlet.internal.ServletStubImpl.prepareServlet(ServletStubImpl.java:539)
    at weblogic.servlet.internal.WebAppServletContext.preloadServlet(WebAppServletContext.java:1976)
    at weblogic.servlet.internal.WebAppServletContext.loadServletsOnStartup(WebAppServletContext.java:1950)
    at weblogic.servlet.internal.WebAppServletContext.preloadResources(WebAppServletContext.java:1869)
    at weblogic.servlet.internal.WebAppServletContext.start(WebAppServletContext.java:3126)
    at weblogic.servlet.internal.WebAppModule.startContexts(WebAppModule.java:1512)
    at weblogic.servlet.internal.WebAppModule.start(WebAppModule.java:486)
    at weblogic.application.internal.flow.ModuleStateDriver$3.next(ModuleStateDriver.java:425)
    at weblogic.application.utils.StateMachineDriver.nextState(StateMachineDriver.java:41)
    at weblogic.application.internal.flow.ModuleStateDriver.start(ModuleStateDriver.java:119)
    at weblogic.application.internal.flow.ScopedModuleDriver.start(ScopedModuleDriver.java:200)
    at weblogic.application.internal.flow.ModuleListenerInvoker.start(ModuleListenerInvoker.java:247)
    at weblogic.application.internal.flow.ModuleStateDriver$3.next(ModuleStateDriver.java:425)
    at weblogic.application.utils.StateMachineDriver.nextState(StateMachineDriver.java:41)
    at weblogic.application.internal.flow.ModuleStateDriver.start(ModuleStateDriver.java:119)
    at weblogic.application.internal.flow.StartModulesFlow.activate(StartModulesFlow.java:27)
    at weblogic.application.internal.BaseDeployment$2.next(BaseDeployment.java:1267)
    at weblogic.application.utils.StateMachineDriver.nextState(StateMachineDriver.java:41)
    at weblogic.application.internal.BaseDeployment.activate(BaseDeployment.java:409)
    at weblogic.application.internal.EarDeployment.activate(EarDeployment.java:58)
    at weblogic.application.internal.DeploymentStateChecker.activate(DeploymentStateChecker.java:161)
    at weblogic.deploy.internal.targetserver.AppContainerInvoker.activate(AppContainerInvoker.java:79)
    at weblogic.deploy.internal.targetserver.BasicDeployment.activate(BasicDeployment.java:184)
    at weblogic.deploy.internal.targetserver.BasicDeployment.activateFromServerLifecycle(BasicDeployment.java:361)
    at weblogic.management.deploy.internal.DeploymentAdapter$1.doActivate(DeploymentAdapter.java:51)
    at weblogic.management.deploy.internal.DeploymentAdapter.activate(DeploymentAdapter.java:200)
    at weblogic.management.deploy.internal.AppTransition$2.transitionApp(AppTransition.java:30)
    at weblogic.management.deploy.internal.ConfiguredDeployments.transitionApps(ConfiguredDeployments.java:240)
    at weblogic.management.deploy.internal.ConfiguredDeployments.activate(ConfiguredDeployments.java:169)
    at weblogic.management.deploy.internal.ConfiguredDeployments.deploy(ConfiguredDeployments.java:123)
    at weblogic.management.deploy.internal.DeploymentServerService.resume(DeploymentServerService.java:180)
    at weblogic.management.deploy.internal.DeploymentServerService.start(DeploymentServerService.java:96)
    at weblogic.t3.srvr.SubsystemRequest.run(SubsystemRequest.java:64)
    at weblogic.work.ExecuteThread.execute(ExecuteThread.java:201)
    at weblogic.work.ExecuteThread.run(ExecuteThread.java:173)
    >
    My composite.xml is:
    <composite name="JIPSYHandleRTOTaskEBF" revision="1.0" mode="active" state="on"
    xmlns="http://xmlns.oracle.com/sca/1.0"
    xmlns:ui="http://xmlns.oracle.com/soa/designer/"^M
    xmlns:xs="http://www.w3.org/2001/XMLSchema">^M
    <import location="GetTimeoutPeriod.wsdl" namespace="http://xmlns.oracle.com/pcbpel/adapter/db/GetTimeoutPeriod/"/>
    <service ui:wsdlLocation="JIPSYHandleRTOTaskEBF.wsdl" name="client">
    </composite>
    But when it has been deployed, I see that this has been changed into:
    <composite name="JIPSYHandleRTOTaskEBF" revision="1.0" xmlns:xs="http://www.w3.org/2001/XMLSchema">
    <import location="GetTimeoutPeriod.wsdl" namespace="http://xmlns.oracle.com/pcbpel/adapter/db/GetTimeoutPeriod/"/>
    <service ui:wsdlLocation="JIPSYHandleRTOTaskEBF.wsdl" name="client">
    </composite>
    (I exported this from MDS).
    Apparently, some namespaces are stripped.
    This appears to happen during the deploy (using ant), because the version in the generated jar file is already missing the namespaces.
    The BPEL processes appear to work fine though.
    Why is this happening and how can I prevent these errors?

    I've fiddled around with the file composite.xml and found the following workaround:
    If I change the start of the file to:
    <?xml version="1.0" encoding="UTF-8"?>
    <composite name="JIPSYUpdateWorkflowReqABCSImpl"
    xmlns="http://xmlns.oracle.com/sca/1.0"
    xmlns:ui="http://xmlns.oracle.com/soa/designer/"
    xmlns:xs="http://www.w3.org/2001/XMLSchema"
    revision="1.0"
    mode="active"
    state="on">
    it remains unchanged and the errors during deployment are gone.

  • Error:  Namespace prefix 'split-by-page-break' used but not declared.

    I have my machine reimaged, now when I try to preview an rtf template I get the below error. Nothing has changed in my template and I am using 1.0.0 Build 9 as before my reimage as well. This is an uregent problem that I am not able to find the solution for on my own. Please advise with any help.
    Caused by: oracle.xdo.parser.v2.XPathException: Namespace prefix 'split-by-page-break' used but not declared.
         at oracle.xdo.parser.v2.XSLProcessor.reportException(XSLProcessor.java:782)
         at oracle.xdo.parser.v2.XSLProcessor.newXSLStylesheet(XSLProcessor.java:564)
         ... 14 more
    Thanks

    I'm just new to XMLP and am receiving the same error.. My error is occuring when trying to use sub-templates in my master template.
    I believe I have the syntax correct:
    To import template file:
    <?import:file:h:///CN_LTR_TEMPLATES.rtf?>
    to call the sub-template:
    <?call-template: signature:?>
    Its the call-template to signature thats generating my error message.. My only thought is that its not calling my import properly..
    Anyway.. Hope this might help you a bit.. you never mentioned anything about using a sub-templates. Perhaps since you formated your computer, your template may be in a different location or gone all together (that is if you are using sub-templates).
    If i figure anything out in the mean time, i'll let you know..
    Edited by: user8682333 on Aug 16, 2009 6:51 AM

  • Namespace Problem? Namespace prefix used but not declared.

    Hello Guru's,
    I am new to XSL templates, while genrating XML publisher report with these template, I am getting below "namespace" error:
    If I remove the "set:"/"str:" expressions from the template, it works fine. Is there anything syntactically wrong in the expression? but not getting the results
    Getting "Caused by: oracle.xdo.parser.v2.XMLParseException: Namespace prefix 'str' used but not declared." error while using this code
                             <xsl:call-template name="str:generate-string">
                                  <xsl:with-param name="text" select="' '"/>
                                  <xsl:with-param name="count" select="30"/>
                             </xsl:call-template>
    Getting "Caused by: oracle.xdo.parser.v2.XMLParseException: Namespace prefix 'set' used but not declared." error while using this code
         <xsl:template name="distinct">
              <xsl:param name="nodes" select="/.."/>
              <xsl:param name="distinct" select="/.."/>
              <xsl:choose>
                   <xsl:when test="$nodes">
                        <xsl:call-template name="distinct">
                             <xsl:with-param name="distinct" select="$distinct | $nodes[1][not(. = $distinct)]"/>
                             <xsl:with-param name="nodes" select="$nodes[position() &gt; 1]"/>
                        </xsl:call-template>
                   </xsl:when>
                   <xsl:otherwise>
                        <xsl:apply-templates select="$distinct" mode="set:distinct"/>
                   </xsl:otherwise>
              </xsl:choose>
         </xsl:template>
    I would appreciate any help in this regard.
    SA

    Declare them in the namespace :)
    <?xml version='1.0' encoding='windows-1252'?>
    <xsl:stylesheet version="1.0" xmlns:xsl="http://www.w3.org/1999/XSL/Transform">
    <xsl:template name="distinct">
    <xsl:param name="nodes" select="/.."/>
    , </xsl:stylesheet>

  • Namespace prefix 'xdosxlt' used but not declared

    I'm trying to remove duplicate data from my dataset (below)
    <MAIN>
    <PODATA>
    <PRJ>..
    </PRJ>
    <PRJ>..
    </PRJ>
    </PODATA>
    <PRJ>..
    </PRJ>
    <PRJ>..
    </PRJ>
    <PODATA>
    </PODATA>
    and followed code as given in below link but getting error message *"Namespace prefix 'xdosxlt' used but not declared"*
    https://blogs.oracle.com/xmlpublisher/entry/removin_duplicates
    In short:_
    Added a variable as
    <?variable:metrics;xdosxlt:distinct_values(PODATA)?>
    and in for loop referring as
    <?for-each:$metrics?><?sort:PONUMBER;'ascending';data-type='text'?>
    I cannot change the SQL as I need data on 2 group levels separately.
    Can you pls assist? I'm EBS 11i and BIP Template Builder for Word 10.1.3.4.2
    Edited by: oraclepro73 on May 8, 2012 3:19 PM

    Hi ,
    When i tried
    <?variable:metrics;xdosxlt:distinct_values(DISTRIBUTIONS_ROW)?>
    i get an error, any idea please?
    Thanks,
    Husam

  • Duplex print setup error - Namespace prefix 'section' used but not declared

    Hi All, I am getting the below error while trying to preview as PDF document. The issue seems to be caused by adding the below to form field in the rtf template (removing the below i can view the PDF document but it does not work as expected ie printing the terms and conditions to back of the page)
    <?section:force-page-count;'end-on-even-layout'?>
    Error::
    Caused by: oracle.xdo.parser.v2.XPathException: Namespace prefix 'section' used but not declared.
         at oracle.xdo.parser.v2.XSLProcessor.reportException(XSLProcessor.java:782)
         at oracle.xdo.parser.v2.XSLProcessor.newXSLStylesheet(XSLProcessor.java:564)
         ... 15 more
    FYI: I have been using the below link as example
    http://blogs.oracle.com/xmlpublisher/2007/10/here_are_my_terms_conditions.html
    Also reviewed the following link too apart from reading the user guide
    http://winrichman.blogspot.com/search/label/BI%20Publisher%20Last%20page%20continued
    Thanks, Maha

    Hi Maha,
    I have used the <?section:....?> command a few times, and I think it has to be enclosed within a <?for-each@section:.....?> loop. If you are still having issues, then upload your template and sample XML somewhere and I can try to take a look for you.
    Regards,
    Cj

  • I dropped the phone, but not light ! I tried to start it with the restoration and upgrading but I do not , what can I do

    I dropped the phone, but not light ! I tried to start it with the restoration and upgrading but I do not , what can I do ?

    If you dropped the device and cannot get it to start up, then you have probably damaged it to the point it needs to be looked at by Apple or your Authorized Apple Service Provider, whomever handles service in your location. User damage is not covered under warranty, so be prepared to pay.

  • Lightroom 1.4.1 Has anybody experienced corrupt print driver using Mac OS X Tiger

    Hi folks,
    I am starting to pull hair out! Whilst nearing the end of a print run for a wedding customer, my HP B9180 has begun to print what looks like dark lines on 'some' areas of my prints. I have done all that I can to resolve this but to no avail! i.e. Ink levels OK. Printer test sheet perfect. Print heads re aligned and cleaned anyway. Print done from Mac itself, such as iPhoto and 'Preview' - result= perfect print. Go back to Lightroom and the same happens, I am at a loss and just eight images away from finishing the job!! HELP!
    Any ideas gladly received. Is it worth trying a fresh install of Lightroom? Any one had a similar experience?
    Paul
    Oh yeah: B9180 printer (with latest firmware). MacBook Pro running OS X Tiger and Lightroom 1.4.1.
    A perfect combination for about a year . . .up until now!

    I don't recall reading any previous reports matching your description. Have you tried deleting the LIghtroom preference file to see if that helps. Occasionally, it can become corrupt.
    See linked article for location of preference file http://forums.adobe.com/thread/358041?tstart=0

  • CSS Float Drop in IE8 but not Compatibility Mode

    I'm testing code for my home page across different browsers, and encountered the common IE float drop problem.  This does not occur in Firefox, Chrome, Opera, or IE8 in Compatibility Mode; but does occur in IE8 standard mode.  It's a bit confusing, since I usually encounter this problem in Compatibility Mode.
    I have tried using clear:none; as I thought the content was clearing the float:left of a large flash image on the left side of the window, but it didn't solve the problem.  I have 3 image buttons whose combined heights equate that of the flash image (all 622px), and these are all in a column div floating to the right.  All of these are flush margin:0 and padding:0, border:none.  The flash image has it's own class stating margin:0, padding:0, border:none as well.  These divs are fixed pixel widths and heights.  I tried placing them in a larger container div with fixed width and height, which didn't solve the problem.  Again, this only occurs in IE8 Compatibility Mode.
    This is the code below:
    div id="container">                  
    embed src="index.swf" allowscriptaccess="always" allowfullscreen="true" height="622" width="509" align="left" class="flashhome"> /embed>                     
    div id="homecontright">           
      a href="services.html?panel=5">           
      img src="button1.gif" align="top" border="0" alt="b1" class="imageright"/> /a>                        
      a href="smt.html">          
       img src="button2.gif" align="top" border="0" alt="b2" class="imageright"/> /a>                       
       a href="jobs.html">          
       img src="button3" align="top" border="0" alt="b3" class="imageright"/> /a>        
    /div>       
      div class="floatfix"> /div>             
       div id="foot" align="center">      
       contact info footer      
       /div>             
       /div>
    Here is the style information from my separate stylesheet
    #homecontright { margin:0; padding:0; border:none; width:493px; height:622px; overflow:visible; float:right; display:block; }
    .imageright {margin-left: auto; margin-right: 0px; margin-top: 0px; margin-bottom: 0px; display: block; float: right }
    .flashhome { width:509px; height:622px; margin:0; padding:0; float:left; border:none; }
    div#container { margin-left:auto; margin-right:auto; margin-bottom:0; width:1002px; background-color:#A8CBE9; }
    div#foot {      background-color:#003366;      border-color:#a8cbe9;      border-width:thin;      border-style:solid;      font-size:10px;      width:996px;      padding:0.2em;      margin-left:auto;     margin-right:auto;      text-align:center;      font-family:Arial, Helvetica, sans-serif;      font-weight:bold;      color:#FFFFFF;      height:10px; }
    .floatfix { clear:both; }
    I've tried removing all the floats, even, especially the ones in the nested divs/class elements; but this didn't do a thing.  This leads me to wonder if this really is a float drop problem or am I missing something?
    EDIT: I fail at posting code so I've removed the front bracket from all tags.  Also, added a diagram to show what it's supposed to look like and what is happening in IE 8 Compatibility.  The margins do not exist, they are there so you can see individual elements

    I tried adjusting the images on the right -10px and had the same result.  Those images were actually created with margins within the image, so everything should be flush.
    I noticed, however, that even in browsers where everything aligns correctly, there seems to be a 2-3px jog between the flash image and the buttons on the right.  That strange link to the bottom right of the flash image is still appearing as well, somehow having to do with the top banner image when right clicked.  I tried changing the URL of that banner and the link changed as well, confirming my suspicion that they're linked.  I attempted to contain that image in a fixed width div with no results.  This link does not appear in other browsers, nor does it appear on any other pages that I used that code on.
    Code for my banner:
    <...a href="index.html"><img src="index/accuweb_c3homebannerR1a.jpg" alt="banner" border="0" class="banner"/><.../a>

  • E2500 randomly drops internet connection but not the home network.

    I have an E2500 with the latest firmware upgrade (1.0.03). My configuration is simple, I have a fixed IP from my ISP with fixed DNS servers. I have one computer connected via cable and one connected via wireless and a laptop that gets connected on occasion wirelessly as well. I also have an android phone that I sometimes have the networking turned on and sometimes not. That doesn't seem to be affecting the router either as I've lost connections under both circumstances. The only thing I have different is I clone the MAC address as the ISP has my IP linked to my old Linksys MAC.
    The problem is I randomly lose connection to the internet, the home network is still up it's just the internet goes down. I could be on the computer or not, sometimes while browsing sometimes after I browse for a while sometimes before I get started. Fortunately its not happened during one of my online games but it has happened just after I log off the game. It usually happens a couple of times a day.
    My fix has been to simply log into the router via html and on the status screen click the reboot button, then the ok, then the continue (I know it by heart). I wait 30 seconds or so and bingo I have my internet back. It's a pain that I'd like to get fixed.
    Any ideas?
    JB

    There might be some settings required in the router so that it gets the proper solution. If you are facing the concern of getting lag, dropped connections then you can try the following steps:
    A] With the help of Cisco Connect Software (if at all you have installed the router with the help of this software)
    1] Open the software and go to the option which says "Router Settings"
    2] Then click on the option which says "Advanced Settings" which will take you to the router's configuration page.
    3] On that same setup page reduce the MTU value to 1400 from Auto
    4] Then go to the Wireless tab, keep network mode as mixed,
    For Channel Settings of 2.4 GHz you can make Channel Width to 20 MHz only and Channel to 6, 9, 11..
    For Channel Settings of 5 GHz you can make Channel Width to 20 MHz only and Channel to 40 or 161...
    B] If you haven't installed Cisco Connect then you can log on to the router's user interface using it's default IP address in the browser which is 192.168.1.1 and type in 'admin' as the password leaving the username field blank. This will take you to the router's web interface and then follow steps as mentioned above to make the changes.

  • N97 Homescreen Error - "already in use" but not ac...

    Yesterday my N97 switched itself off and when it came on it would only show the menu screen and not the homescreen. If I try to access the homescreen it tells me "its already in use" and keeps diverting back to the menu screen.
    All applications are working, along with texts and phone calls. Its just highly annoying.
    This has occurred since the latest software update.
    I have tried a factrory reset but this has not helped.
    Can anyone advise?
    Thanks
    Solved!
    Go to Solution.

    Before attempting any other reset methods try these tips:
    Whilst in the main menu go to Settings > Themes > General and change the theme to something else to see if that solves it.
    If that fails try to think what widgets were on your homescreen (such as facebook or accuweather).  Go to Settings > Application mgr > Installed apps now find those widgets and uninstall them if you can. 
    Reboot after trying each method. 
    Message Edited by psychomania on 07-Jan-2010 01:05 PM

  • My IPod Clasic will sometimes display the error "lost connection" when it's being used, but not when connected to my computer.  Any ideas?

    This does not happen when connected to a docking device or computer, only when it is being used with headphones.  If I reboot, it's fine, but it does happen again.

    Have  discovered that I had not in fact updated the ios!!
    Went through the process last night and my ipod now works fine on my docking station.
    Thank you very much for your advice.

  • Dropping network drives but not internet

    I am having a problem with a MacBook that is dropping our companies network shared drive on a Windows serve. The laptop is connected via a Buffalo Wireless 802.11g network. We have 3 Windows systems XP and Vista, that stay connected all day. The MackBook is dropping the network connection about every 10-15 minutes but the internet is still connected.
    There is a second wireless network that the same MacBook trys to connect to but is not the primary, it does not have access to the share. Could the system be going between the two?
    Thanks
    David

    Hey,
    I have a similar opposite problem. (see my post on "dropping" posted earlier. I have three macs and 2 PC's. The 4 all work great wireless. The PC which is connected through the router(ethernet) drops all the time - several times a day. Not good enough yet to fix it.
    Good Luck, Seems hard to get answers.

  • Can use but not edit/change old panels in Configurator 3.1

    I have Configurator panels I’ve created some time ago (in Configurator 1.0, I think) that I would like to use with CS6 *and* edit with Configurator 3.1.  I found a "Panels" folder in my CS5 Plugins folder, copied it to the CS6 Plugins folder, and was able to see and use the panels (Windows > Extensions).
    However, I can’t see how to edit/change them.  When I try to open a panel from Configurator 3.1 (or 2.0 or 1.0), it demands to look for a file with the ".gpc" extension.  The old panel files (that are currently recognized by CS6, thank goodness for that) are stored as “.mxi” (plus other related files/assets in sub folders).  I think Configurator is looking for a “project” file, but there are no .gpc files on my drive (other than a couple that were installed in the Configurator 3.1 folder).
    This inabaility to open anything other that .gpc files seems to be the case with 1.0 and 2.0 as well.
    Am I doing something wrong?
    Windows 7 Home Premium

    The .gpc file is the source file of a panel created by Configurator. The contents you found in CS5 Plugins folder are exported files. You can open and edit with the source file (with gpc extension) of the panel, and export it to panel files. But you can not generate a gpc source file from exported panel files.
    If you have the original gpc file, even created by Configurator 1.0, Configurator 3 can migrate it to gpc file for Configurator 3 to edit or change. If you don't have such file, Configurator 3 can not help you. You need to create the panel again.

  • Photos show in itunes capacity used but not on phone or in sync

    i updated my wifes iphone 3g to ios4 and it only shows 10 photos on he iphone but when it is connected to itunes in the cappacity bar it shows ther a 576 photos how can i make it so i can see them again .. i have tryed syncing them and restoring the backup and restoring the phone and it still shows them as used capacity but i still can,t see them

    Is Sync Photos selected under the Photos tab for the iPhone sync preferences with iTunes along with folder of photos selected to be transferred from the computer to the iPhone?
    If so, these photos are not included with the iPhone's backup. Photos in the iPhone's Camera Roll are included with the iPhone's backup and although included, photos in the Camera Roll should be imported by your computer as with any other digital camera.
    Are these photos that are or were in the iPhone's Camera Roll or that were transferred from the computer to the iPhone via the iTunes sync/transfer process?
    If the latter, try deselecting Sync Photos under the Photos tab for the iPhone sync preferences with iTunes followed by a sync. This will remove all photos from the iPhone that were transferred from the computer. Follow this be reselecting Sync Photos and selecting the folder of photos to be transferred to the iPhone followed by a sync.
    If these are photos in the Camera Roll, have any of these photos been imported by the computer? If not, try importing these photos with your computer.

Maybe you are looking for