Is it possible (and does not cause any problems) to create a disk image inside a disk image?

Hey there,
I'd like to setup a password protected Disk Image with several different password proteced disk images inside. Such as different levels of security. is that possible at all and if yes, is there anything to consider or any known issues?

sorry my englisch is not that good. I don't understand your sentence. what does it no to both queries mean?

Similar Messages

  • Trying to upgrade from OS9 to 10.2.3, get as far as "select a Destination"  the installation stalls and does not show any destination disks

    I have a Power Mac G4, it has OS 9.  Imam trying to upgrade to OS 10.2.3 (Jaguar).  It is going smoothly until I get to the "Select Destination"  screen.  It stalls there and does not show any disks to choose from.
    Any ideas?
    Thanks. Abe Oliver

    Hello Abe,
    If it's a Digital Audio or earlier, you need to install a Firmware update first...
    As explained in "Mac OS X 10.2 Welcome and Install Manuals" and "Mac OS X Welcome and Install Manuals", you may need to update the firmware on your Macintosh computer prior to installing Mac OS X 10.2 or later. The following table lists the firmware updates that are available for Apple products that can update to Mac OS X 10.2 or later.
    http://support.apple.com/kb/HT1395?viewlocale=en_US
    Power Mac G4
    Firmware Update
    Download Document No.
    Power Mac G4 (Mirrored Drive Doors 2003)
    no update needed
    Power Mac G4 (FW 800)
    no update needed
    Power Mac G4 (Mirrored Drive Doors)
    no update needed
    Power Mac G4 (QuickSilver 2002)
    no update needed
    Power Mac G4 (QuickSilver)
    no update needed
    Power Mac G4 (Digital Audio)
    Power Mac G4 Firmware Update 4.2.8
    120068
    Power Mac G4 (Gigabit Ethernet)
    Power Mac G4 Firmware Update 4.2.8
    120068
    Power Mac G4 (AGP Graphics)
    Power Mac G4 Firmware Update 4.2.8
    120068
    Power Mac G4 (PCI Graphics)
    no update needed
    Power Mac G4 Cube
    Power Mac G4 Cube Firmware Update 4.1.9
    75129

  • I have a mid-2011 iMac running Mavericks. When I click restart the computer goes to a white screen with a spinning circle and does not go any further until I hold down the power button to turn it off. What do I do?

    I have a mid-2011 iMac running Mavericks. When I click restart the computer goes to a white screen with a spinning circle and does not go any further until I hold down the power button to turn it off. What do I do?

    Ok, sounds like the safe mode boot worked... You probably don't want to always be in safe mode though (some reduced functionality) so does it do a normal boot now? If not, you should then reboot into safe mode and run Disk Utility. Then select Macintosh HD on the left hand side, and click the Verify Disk button. If needed, it will ask you to Repair Disk. If there are errors found, Repair Disk again until there are none. Then try another normal boot and reply with result, wether good or bad.

  • When my Mac battery dies and I turn it back on, it always crashes on the grey screen with the progress bar, then it restarts (taking forever) and does not remember any of the programs I was running. MacBook Pro 13 inch running Mavericks

    When my Mac battery dies and I turn it back on, it always crashes on the grey screen with the progress bar, then it restarts (taking forever) and does not remember any of the programs I was running. MacBook Pro 13 inch running Mavericks

    http://osxdaily.com/2014/10/17/os-x-yosemite-installation-stuck/
    also use the Command-L to view logs during installation

  • Hello I nous receive calls or messages and does not receive any can help me

    hello I do not understand how it is that it captures my iphone but does not pass any calls or messages and does not receive any can help me

    I'm sorry but your post doesn't make a whole lot of sense. You may want to try reposting in your native language.
    Best of luck.

  • Computer crashes/hangs and does not accept any command?

    why after opening Windows, computer crashes and does not accept any command?
    only solution (compromise) which I found is to disconnect and reconnect the PC unit; Windows runs properly after the surgery to close it; next morning found the same problem...

    Hello Liviu,
    Welcome to the HP Forums, I hope you enjoy your experience! To help you get the most out of the HP Forums I would like to direct your attention to the HP Forums Guide First Time Here? Learn How to Post and More.
    I have read your post on how after your computer loads Windows, it locks up or freezes, and I would be happy to assist you in this matter!
    For further assistance, I will need to know:
    The Product and Model Number of your desktop computer.
    The version of Windows you have installed on your computer.
    If your computer has completed all of its important Windows Updates.
    If you have updated your HP drivers using the HP Support Assistant.
    If this is an on-going, or recent issue.
    If you have added any new software or hardware to your computer.
    If the computer is plugged directly into a wall outlet.
    Please re-post with the necessary information, this way I will be able to research this further for you. I look forward to your reply!
    Cheers! 
    MechPilot
    I work on behalf of HP
    Please click “Accept as Solution ” if you feel my post solved your issue, it will help others find the solution.
    Click the “Kudos, Thumbs Up" on the right to say “Thanks” for helping!

  • Why does my MacBook come up with window saying "setting Up Mac" when I turn it on and enter my password and stays there and does not go any further

    Why does my MacBook come up with window saying "setting Up Mac" when I turn it on and enter my password and stays there and does not go any further

    You may want to put this question on the MacBook community forum to get a better response.
    https://discussions.apple.com/community/notebooks/macbook

  • HT4859 If I upgrade to an Iphone 4s, can I delete the account from my old Iphone and will it cause any problems?

    I have upgraded to an Iphone 4s from an Iphone, can I delete the icloud account of the old phone on my new one without it causing any problems? it seems to have a lot of storage  (3.3Gb)

    You should be able to copy all of your purchases (apps, music, films etc) from your current iPhone to your computer's iTunes via File > Transfer Purchases. As long as they remain available in the store then apps can be re-downloaded, music can be re-downloaded in some countries, and TV shows and films in fewer (and even where films can be re-downloaded not all film studios have agreed to it) - ringtones and audiobooks can't be re-downloaded.
    Re-downloading : http://support.apple.com/kb/HT2519
    In terms of the apps content and settings, then if you backup the phone to your computer's iTunes then you should be able to restore that backup onto your new phone : how to backup and restore. Passwords (email, router, website) won't be restored onto a different device so you will need to re-enter them on your new phone.
    You can also copy photos off your current phone. Just in case the backup and restore doesn't work (it should but it's best to be safe), you may also want to copy any important documents off your current phone as well e.g. via the file sharing section at the bottom of the device's apps tab when connected to iTunes, via wifi, email, dropbox etc.

  • TS3274 I have an iPad 1 and have not had any problems until recently and now find I am continually being kicked outnofcwebsites and have to go back into them, why?

    I have an iPad 1 and until recently I have not had any problems. Lately I find I am being kicked out of websites and have to start again. There does not seem to be a problem with my Internet connection as it is okay when using my laptop.

    The Basic Troubleshooting Steps are:
    Restart... Reset... Restore from Backup...  Restore as New...
    Restart / Reset
    http://support.apple.com/kb/ht1430
    Backing up, Updating and Restoring
    http://support.apple.com/kb/HT1414
    Try this First... You will Not Lose Any Data...
    Turn the iPad Off... ( if it isn’t already )
    Press and Hold the Sleep/Wake Button and the Home Button at the Same Time...
    Wait for the Apple logo to Appear and then Disappear...
    Usually takes about 15 - 20 Seconds... ( But can take Longer...)
    Release the Buttons...
    Turn the iPad On...
    If you try all these Steps and you still have issues... Then a Visit to an Apple Store or AASP (Authorized Apple Service Provider) is the Next Step...
    Be sure to make an appointment first...

  • My location bar has stopped recognising my history or bookmarks and does not autocomplete any websites

    I have disabled all add-ons, and upgraded to the most recent version of FF. If I go to my History library, my full browsing history is there and I have a lot of bookmarks. The problem is the location / address bar does not auto-complete, and nothing happens when I click on the drop down arrow at the RHS of the address bar... any help would be brilliant as extensive googling hasn't provided a solution!

    Did you also check:
    [http://kb.mozillazine.org/Menu_differences Firefox > Preferences] > Privacy > Location Bar: When using the location bar, suggest: History, Bookmarks, History and Bookmarks
    This can be a problem with the file places.sqlite that stores the bookmarks and the history.
    * http://kb.mozillazine.org/Bookmarks_history_and_toolbar_buttons_not_working_-_Firefox

  • Ligthroom 5.5 after installing the software does not start and does not give any kind of mistake

    I subscribe to CC as a photographer and just inatalar Ligthroom but this does not start and no daningun mistake. Reinstall several times but still the same. What can be the problem?
    thanks

    Hola, arreglado por mi parte también, chateando (en inglés...) con un operador que ha demostrado conocer perfectamente la solución (para Win7):
    En carpetas "C:\Program files (x86)\Common Files\Adobe\" y "C:\ProgramData\Adobe\" deben activarse permisos de control total para el usuario (que puede no tener control total en el sistema) y desactivar "solo lectura" a las carpetas descritas y sus subcarpetas para que al iniciar se configure el registro adecuadamente. Una vez hecho esto me ha funcionado todo a la primera, me lo han explicado paso a paso por el chat. Un 10 para el técnico, un suspenso para Adobe por no publicar adecuadamente la solución.
    Gracias manufoto por tu explicación, parece que todo va a parar a las mismas carpetas.
    Saludos

  • New-csEXUmContact does not generate any output or create a contact

    Hi,
    I have Lync 2013 on Prem and Exchange o365. 
    I am trying to create a Auto attendant as per this article:
    http://ahandyblog.wordpress.com/cloud-technologies/office-365-auto-attendant-with-lync-2013-on-premise/
    but when I execute the New-csEXUmContact, it does nothing. No contact gets created and neither a GUID output is generated. I have no clue how to troubleshoot further.
    Any help is appreciated.
    Thanks,

    New-CsExUmContact -SipAddress “sip:[email protected]”
    -RegistrarPool “your_lync_fqdn”
    -OU “LAB Users” -DisplayNumber “required_extension”
    -AutoAttendant $True -Verbose
    New-CsExUmContact -SipAddress “sip:[email protected]”
    -RegistrarPool “your_lync_fqdn”
    -OU “LAB Users” -DisplayNumber “required_extension”
    -AutoAttendant $True -Debug
    can we try these?
    Please remember, if you see a post that helped you please click "Vote As Helpful" and if it answered your question please click "Mark As Answer" Regards Edwin Anthony Joseph

  • Firefox downloads but does not install on my Win7 64 bit laptop and does not show any files in the software list of programs installed.

    I have installed and uninstalled several times with no success. I had a previous version installed in April 10 but it will not reinstall or run. This problem started about a month ago, in early July.

    moirl wrote:
    5.  I can not get anything off the Blackberry (photos etc.).
    As was stated above:
    1. Go to Options >> Media Card (or Memory)
    (some themes or BlackBerrys may call this "Settings >> Media Card")
    2. Check the following settings (if they are not listed this way, then change to reflect the following:
    a) Media Card Support: On
    b) Mass Storage Mode Support: On
    c) Auto Enable Mass Storage: Yes
    3. Save the settings and exit
    1. If any post helps you please click the below the post(s) that helped you.
    2. Please resolve your thread by marking the post "Solution?" which solved it for you!
    3. Install free BlackBerry Protect today for backups of contacts and data.
    4. Guide to Unlocking your BlackBerry & Unlock Codes
    Join our BBM Channels (Beta)
    BlackBerry Support Forums Channel
    PIN: C0001B7B4   Display/Scan Bar Code
    Knowledge Base Updates
    PIN: C0005A9AA   Display/Scan Bar Code

  • HT1320 I have a white screen cannot read anything and does not play any advice

    My ipod nano has a white screen and I cannot see anything on it any advice

    Reset iPad
    Hold down the Sleep/Wake button and the Home button at the same time for at least ten seconds, until the Apple logo appears
    Note: Data will not be affected.

  • TS1372 My ipod shuffle blinks grn,amber,grn, amber,grn,amber and does not play any music

    I am unable to use my ipod because it blinks green and amber three times and I get no music.  It was working fine until I was charging it and my wife used the computer while it was charging, not to say she did anything of course.  At the present time I am unable to do anything with it, if anyone can help I would be appriciate it.
                                                              Thank, Harry

    If the light stays green then it won't play music. You're probably right that the Reset Utility won't help you in this case, but it'd be better if you clearly stated that you'd tried it without effect instead of an assurance that it's not the fix for you.
    Had you gone to the iPod Shuffle Support Page you could have followed links to several different Knowledge Base (KB) articles which address this issue. Seeing as how you missed that, here are a couple of them:
    http://docs.info.apple.com/article.html?artnum=303332
    http://docs.info.apple.com/article.html?artnum=303140

Maybe you are looking for

  • Displaying columns of alv with Main Heading and Sub Heading

    Hi friends. I have certain fields in display of ALV. Out of all fields(columns), I would have to display some columns with one Main Heading,Below it's being split in multiple rows. I have data relevent to that multiple fields. Let say , In first row

  • Can I have mail and contacts open at the same time

    I really want to be able to have one or more iCloud Apps open at the same time; for example, I may be looking up some info on a contact or in calendar in order to mail someone. At times I have just opened a different tab, but it seems that iCloud the

  • External hardrive problems

    Hey there! So I just brought the SONNICS external hard drive with 999GB of memory. I have a Macbook OS X version 10.6.8 - It has finally run out of space which is why I bought the external drive. I have plugged in the SONNICS and have followed instru

  • Site studio 10gr4 case study or learning material

    hi All, I need some learning material for site studio 10gR4, so any recommendations ? thanks in advance

  • Selecting a jlist item and placing it in view

    i have 100 items in a jlist. then i scrolled to the bottom of the list.....so now the first item is not in view anymore. i have a button on top that retrieves rows and rebuilds the jlist. which it does. however, if i am at the bottom of the list and