Is it possible DLSW with remote ack for LLC2.?

Hello.:
In the following env I have an SNI connection:
3745-Tokenring/2612-FrameRelay-2612/Tokenring-OSA.
the 2612 is DLSW.
I have noticed, sometimes,when there is a HW problem in the right side, the 2612left, maintains the LLC2 session with R/Rs and not disconecting the session blocking the Virtual Route in the NCP of 3745.
Is there an eassy way of doing remote ACK for Token ring LLC2 using DLSW over Frame Relay.?
Is the source-bridge passthrough xxx command supported by DLSW.?
Thanks a lot.
Casimiro

Hi,
if you need the RR's ect to flow across dlsw than you can use dlsw fst. With fst dlsw does not do local-ack anymore. that means that all frames including RR's are transported to the other side. The llc2 connection is then truley end to end betweeen the 3745 and the tokenring OSA.
However you must be aware of a couple of limitations.
Depending on your mtu on the tokenring i assume 4k. You must either configure the lf parameter on the dlsw remote peer statment to a value below the mtu of your WAN or you must make sure that the WAN can carry a maximum tokering frame + 12 bytes dlsw fst header + ip header. You might have to increase the mtu on your frame relay interfaces.
With fst there is no tcp session anymore doing the segmentation of large frames, every packet is encapsulated individualy and send right away.
Besides that you have only limited visibility to the sessions since the router is not participating in any llc2 connections, the router simply forwards packets.
thanks...
Matthias

Similar Messages

Which Stereo Bluetooth headset with remote supports for Iphone3Gs??

please anybody can tell me which is the best Stereo Bluetooth headset with remote support for Iphone3Gs??
thanks in advance

Hello thomulusmax,
Welcome to the BlackBerry Support Community Forums
As long as your device is running software version 4.2.2 or higher it supports A2DP. (You can verify this under Options >> About)
Keep in mind that not all Bluetooth headsets are A2DP enabled. As long as your headset supports A2DP and it pairs and connects with your Pearl you should be able to listen to any supported audio format.
Cheers!
Message Edited by FozzyBear on 08-21-2009 02:32 PM
-FB
Come follow your BlackBerry Technical Team on Twitter! @BlackBerryHelp
Be sure to click Kudos! for those who have helped you.
Click "Accept as a Solution" for posts that have solved your issue(s)!

How to connect a printer with Remote Desktop for Mac, version 8

Hello,
I use Microsoft Remote Desktop 8.0.3 with my Mac to connect to an application which is based on a Windows Server 2008.
I don't find the way to print to my Mac. I don't find the menu for it :-(
Same problem to transfert a file from the Windows Server to my Mac :-( :-(
Can you help me ?
Many thanks in advance
William

Hi William,
Please make sure that Forward printing devices is checked. This allows you to use the local printer connects to your Mac in a remote desktop session.
Getting Started with Remote Desktop Client on Mac
http://technet.microsoft.com/library/dn473012
Thanks.
Jeremy Wu
TechNet Community Support

Why won't SKY come up with remote codes for Seiki tv's especially when charging a fortune for SKY

I wish someone could tell me why no remote codes are not available for Seiki tv's instead of coming up with excuses.

Like all new kit, it takes time for the codes to be shared and then programmed into remotes.The Sky Remote has a database of known television codes.Each TV has a group of codes to control the different functions of the TV.Sky develops sets of codes for each TV manufactured and then applies its own code to the control set.The Sky code is what you need to program the Sky remote so that it uses the control set for the selected TV. Each Sky remote is programmed with updated code databases when it is manufactured and to keep track of what remote does what, it is given a Rev number found inside the battery bay of the remote. In the case of Seiki, the code set was not incorporated by Sky until Rev 10.Anything earlier will not work unless by sheer chance it matches the code set of another TV.

Possible bug with v2.1 for N97?

Connecting to web now always opens the 'search for wlan?' dialog. Hitting cancel sends me to the bookmarks menu, it doesn't connect via 3G at all.

Had to do a hard reset after the update. Annoying but expected I guess.
Oh well, here's to a day of re-installing all my apps

My Apple Earphones with Remote and Mic White For iPhone says: made in vietnam. i want to know if they are OEM?

My Apple Earphones with Remote and Mic White For iPhone says: made in vietnam right in the cord. i want to know if they are OEM? here my email: [email protected], thanks.

Accidental damage is not covered under the warranty but if possible to reset the screen without causing additional damage, the Apple Store should do this without charging for it.

Setting up a remote with ir-tables for use with XBMC

My main goal is to use a remote with xbmc, but I'm having issues.
Issue #1 (main problem): The directional keys and enter will work but no other keys seem to register.
Issue #2: Even the keys that work have this weird usage issue, where pressing any of the same key twice loses the second key press. For example clicking up arrow 4 times results in only two actual "up's" being done. (first up works, second fails, third works, forth fails, etc)
I've spent about four hours getting to this point and there is a lot of conflicting information out there on this subject which has had me very confused, but at this point I assume I can ignore any mention of Lirc as it seems like its not needed and if ir-keytable is used correctly things should just work?
Quote from www.lirc.org: "Recent linux kernels make it possible to use some IR remote controls as regular input devices"
What I have got/done:
Machine: Zotac Zbox Nano AD10 with remote.
Linux: Manjaro Openbox Addition
Testing in applications: XBMC, Leafpad, Terminal
[david@zotac ~]$ dmesg | grep CIR
[ 4.444693] ite_cir: Auto-detected model: ITE8704 CIR transceiver
[ 4.444701] ite_cir: Using model: ITE8704 CIR transceiver
[ 4.478490] input: ITE8704 CIR transceiver as /devices/virtual/rc/rc0/input8
[ 4.478531] rc0: ITE8704 CIR transceiver as /devices/virtual/rc/rc0
[david@zotac ~]$ ir-keytable
Found /sys/class/rc/rc0/ (/dev/input/event6) with:
Driver ite-cir, table rc-rc6-mce
Supported protocols: NEC RC-5 RC-6 JVC SONY SANYO LIRC other
Enabled protocols: NEC RC-5 RC-6 JVC SONY SANYO LIRC other
Name: ITE8704 CIR transceiver
bus: 25, vendor/product: 1283:0000, version: 0x0000
Repeat delay = 500 ms, repeat period = 500 ms
#My keymaps file contains (I just put the keys that I would like to use with xmbc)
0x8034045b KEY_RIGHT
0x8034045a KEY_LEFT
0x8034045c KEY_ENTER
0x80348459 KEY_DOWN
0x80340458 KEY_UP
0x80348421 KEY_R
0x80340420 KEY_F
0x80348410 KEY_EQUAL
0x80348483 KEY_ESC
0x80348431 KEY_X
0x8034842f KEY_T
0x803404cb KEY_I
0x8034845d KEY_M
0x8034042c KEY_P
0x80340411 KEY_MINUS
I write my keymaps file: (I think /etc/keymaps/[file] would be a better location for this file but it shouldn't matter is that correct?)
ir-keytable -c -w /home/david/Documents/keymaps --device=/dev/input/event6 --period=500 --delay=500
I can verify the settings are registered:
[david@zotac ~]$ ir-keytable --read --device=/dev/input/event6
scancode 0x80340411 = KEY_MINUS (0x0c)
scancode 0x80340420 = KEY_F (0x21)
scancode 0x8034042c = KEY_P (0x19)
scancode 0x80340458 = KEY_UP (0x67)
scancode 0x8034045a = KEY_LEFT (0x69)
scancode 0x8034045b = KEY_RIGHT (0x6a)
scancode 0x8034045c = KEY_ENTER (0x1c)
scancode 0x803404cb = KEY_I (0x17)
scancode 0x80348410 = KEY_EQUAL (0x0d)
scancode 0x80348421 = KEY_R (0x13)
scancode 0x8034842f = KEY_T (0x14)
scancode 0x80348431 = KEY_X (0x2d)
scancode 0x80348459 = KEY_DOWN (0x6c)
scancode 0x8034845d = KEY_M (0x32)
scancode 0x80348483 = KEY_ESC (0x01)
At this point is seems like everything is setup correctly but like I said only the direction keys and return work. If it did work my next step would be determining when to issue the ir-keytable write, and I'm assuming I can just do that in openbox's autostart file?
Does anyone have any ideas as to what I might do to correct these issues?

I also encountered davevallance's issue #1. Directional and enter keys already work, as do volume keys. If any other button is mapped to those working keys (using ir-keytable) then they also work, for example I can successfully map the useless "teletext" to "enter" and it produces a linefeed when pressed but I cannot get it to do the same with "space". Interestingly it does produce a space keypress in a virtual terminal (Ctrl+Alt+F3), also "ir-keytable -t" shows the correct key event which proves the underlying OS is recognising the mapping. The issue is somewhere in the X system instead.
I refer now to HID Remotes which covers the situation well. It explains that X does not process keycodes above 255 and at first that would seem to fit here. All the keys which work (arrows, enter, volume) have keycodes less than 255. So why don't other 'safe' keycodes work too?
Xorg has it's own keycode map with "xmodmap" but I don't think that is responsible in this case. From the Arch wiki it suggests exploring with:
xev | grep -A2 --line-buffered '^KeyRelease' | sed -n '/keycode /s/^.*keycode $[0-9]*$.* (.*, $.*$).*$/\1 \2/p'
Unmapped keys should produce a "NoSymbol" message but for my non-working keys there is no response at all in X. Is there another layer between kernal and GUI?

I shared my itunes account with my daughter for many years while she had only an ipod. She now has her own iphone with her own itunes account. Is it possible to transfer the purchases she made on my account over to her new itunes account?

I shared my itunes account with my daughter for many years while she had only an ipod. She now has her own iphone with her own itunes account. Is it possible to transfer the purchases she made on my account over to her new itunes account?

No. Purchase always remain with the account they were purchased with.

A lost my remote control for apple tv. I want to use my phone as a remote but the applications can' pair with the Apple TV device , how can I pair them without remote?

A lost my remote control for apple tv. I want to use my phone as a remote but the applications can' pair with the Apple TV device , how can I pair them without remote?

Setup for remote app: http://support.apple.com/kb/ht1947
Specifically:
Set up Apple TV (2nd and 3rd generation)
On Apple TV, select Settings from the main menu.
Select General > Remotes > Remote App. If Home Sharing isn't set up on your Apple TV, you should turn it on.
Apple TV (2nd and 3rd generation) uses Home Sharing to stream content from your iTunes library on your computer to your HDTV. If you connect your Apple TV to your iTunes library using Home Sharing, you can use Remote to browse and play content from any iTunes library in the Computers section of your Apple TV. You can also use Remote to select between available speakers to enhance your audio and video experience.

How to configure Time Capsule etc as a local network server with remote access server and for backups

I'm trying to set up new 3TB Time Capsule as a wireless network server (with remote access) and for backups for use in a small office (of two Macs). We have a late 2011 Intel MBP and a brand new MBA both running 10.8.3. We have two external 1TB hard drives that until now have been attached the MBP for storage and backing up that computer, which up until now was the only machine in use. The MBA is for a new employee and we need to share and work on the same files, both here in the office and ideally remotely too via Back to my Mac. The MBP needs constant access. The MBA only occasional. The TC has 7.6.3 firmware and we've set it up using AirPort Utility 6.2. It is currently attached to the MBP via ethernet and it has internet access via a Sagemcom router attached to TC's WAN port.
We've managed to set up a wireless network and both have wireless internet access through the TC
But there are so many issues I don't know where to begin - so I'll start with a description of what we're trying to achieve:
I planned to use the TC as the main server drive and place all the key folders and files there so that both of us can access them wirelessly and remotely. The MBP would back up to the TC and to one or two of the external hard drives - one being attached to the Mac via USB and the other being attached to the TC's USB port. We would back up the important data on the TC using SuperDuper and copy it to both external USB drives.
So , first of all, is that a sensible configuration? Should the 'server' be the one of the external hard drives attached to the TC USB port, backed up regularly to the TC using SuperDuper?

But when you say 'So using USB drive does make sense if you want to use it as a file store', do you mean a USB drive plugged into the TC? I hope that I can attach an external drive to the TC so we can all access and read/write the content wirelessly via the TC network or remotely.
Yes, USB.. as it prevents the sparsebundle mixing with data files. I guess it does depend on how much data you are talking about.. you can use the TC internal disk if you are careful and setup the sparsebundle with fixed sizes once you create them..
And to be clear, I wasn't planning on backing up remotely via BTMM - only to access the shared folders on the TC data drive or USB external drive attached to it. I'm assuming that's ok?
Yes, that is fine. Sorry I got the impression you were going to do backup over internet.
What is the alternative? Having a Mac Mini that's always on? Do I need OS X Server etc.?
A mini would be great.. you don't need server edition.. but I would see how the TC goes.. since you have it and it is much lower power consumption device. It is just that its design is not really for file storage.
One big problem I have is to do with the sharing permissions. For everything on the TC or attached external drive attached to it, it says I have only custom access and every time I try to change permissions it says I don't have the permission to do that. And if I try to change the owner it says my user name is not valid.
How is the security setup on the TC?
The security is a bit tricky.. I must admit since I run windows computer in the network, that I simply turn on the guest account to read and write access. For a business setup that might not be adequate but it allows me full access to all the files.
If you setup the TC with user accounts then you are in trouble. That makes it very difficult to access, especially if one person already has the file open you may find a second user cannot login. I am not sure as I have avoided the security. IMHO it is meaningless.. since anyone with physical access to the TC can press the reset for one second and has full access.. and can add or change passwords.

Hello. I began with the DPS. Is it possible to publish a magazine for a limited, specific target group? For example, in one department of a large company? Or to the responsible for various services? If so, how should I do? Thank you for your help.

Hello.
I began with the DPS. Is it possible to publish a magazine for a limited, specific target group? For example, in one department of a large company?
Or to the responsible for various services? If so, how should I do? Thank you for your help.

Short answer is yes.
Click the request for consultation link in Digital Publishing Suite Help | DPS pricing options to receive a price estimate for the DPS license your project.

What does this statement mean: "There is a problem with your authentication, possibly due to inactivity. For your safety, you have been logged out and must sign in again to continue?"

I am able to make it to the site for about 2 seconds and then I am quickly logged off and the statement, "There is a problem with your authentication, possibly due to inactivity. For your safety, you have been logged out and must sign in again to continue."
I don't have a clue as to the problem but since this is impacting my participation in these classes and ultimately could have a negative impact on my grade, I am more than a little concerned!

Have you allowed this site to set cookies?

Is it possible to packaging Air application for Mac AppStore with Air 3?

Is it possible to packaging Air application for Mac AppStore with Air 3 ?

Anyone from adobe? Anyone?
Also I was wondering what could prevent the window from going
away when user uses windows "show desktop" command, or perhaps
there is a way to restore it right away?
thanks.

Hello! I need Apple (!!!) headphones for Ipod Shuffle 3! (only apple earphones with remote and mic!!!) Tell me, what distinguishes the model are presented in black and white boxes? They may differ in features? Can one model is more modern than the other?

Hello!
I need Apple (!!!) headphones for Ipod Shuffle 3! (only apple earphones with remote and mic!!!)
Tell me, what distinguishes the model are presented in black and white boxes? They may differ in features? Can one model is more modern than the other?
Thanks in advance!

Hi Fencer1986,
I apologize, I'm a bit unclear on your request. If you have questions about headphone compatibility for your iPod shuffle 3rd Gen, you may find the following article helpful:
iPod shuffle (3rd generation): About headphone compatibility
http://support.apple.com/kb/ht3472
Regards,
- Brenden

Earphones with Remote and Mic (for Voice Recorder??)

Hello, today I find this Earphones with Remote and Mic on Apple store:
http://store.apple.com/us/product/MB770
It will work on iPod touch (2nd generation), so does it mean the voice recorder app (bought from App Store) is going to work on the iPod touch (2nd generation) as well?? Or the Mic is just working for the phone function??
Anybody know?
Thanks.
Raymond

We were talking about the $29 ones...they seem to be out of stock online (?)..the $79 haven't been released yet....
here's some real cheap ones on amazon....varying reviews....other options listed as well...
http://www.amazon.com/Stereo-Headset-Built-Microphone-Button/dp/B000VVERJI/ref=s r1_1_s9rk?ie=UTF8&s=electronics&s9r=8a10809b1c651770011c93b305dd04c4&itemPosition=1&qid =1224523249&sr=1-1

Is it possible DLSW with remote ack for LLC2.?

Similar Messages

Maybe you are looking for