Is it possible for a battery to be perfectly fine one day and then just die
my black MacBook battery just died the other day, its an aftermarket unit that came with my MB I bought it used. he computer has been working great only issue is original battery was pretty worn so seller bought an additional and kept the factory one as a spare, however I'm having to use tha spare which is holding maybe an hour charge if that because the "good" battery laid an egg, suddenly and without warning, computer shut down and wouldn't come back to life till I changed battery for original one and the aftermarket battery now doesn't even charge, it will go up to 3 lights and after 5 minutes be back down to 1 flashing light. Is there an issue here or is this just a dead battery?
Lyssa you are becoming my angel, hope you take a look at my DVD stuck in drive post too .
Here is the system profiler info as it is I'm probably going to get some used batterie(s) of ebay but I wish I could forgo that process, I'll profile the battery that died when I get home. Thank you Angel, er.....I mean Lyssa
Battery Information:
Model Information:
Serial Number: DP-ASMB013-34ae-250d
Manufacturer: DP
Device name: ASMB013
Pack Lot Code: 0001
PCB Lot Code: 0000
Firmware Version: 0102
Hardware Revision: 0300
Cell Revision: 0100
Charge Information:
Charge remaining (mAh): 118
Fully charged: Yes
Charging: No
Full charge capacity (mAh): 118
Health Information:
Cycle count: 214
Condition: Check Battery
Battery Installed: Yes
Amperage (mA): 130
Voltage (mV): 12563
System Power Settings:
AC Power:
System Sleep Timer (Minutes): 45
Disk Sleep Timer (Minutes): 10
Display Sleep Timer (Minutes): 30
Automatic Restart On Power Loss: No
Wake On AC Change: No
Wake On Clamshell Open: Yes
Wake On LAN: No
Display Sleep Uses Dim: Yes
Battery Power:
System Sleep Timer (Minutes): 0
Disk Sleep Timer (Minutes): 0
Display Sleep Timer (Minutes): 5
Wake On AC Change: No
Wake On Clamshell Open: Yes
Display Sleep Uses Dim: Yes
Reduce Brightness: Yes
Hardware Configuration:
UPS Installed: No
AC Charger Information:
Connected: Yes
Charging: No
Similar Messages
-
I am running Windows 7 Enterprise.
I need to upgrade my version of Itunes from version 7 to version 10 or 11.
I go to Help and click on Search for Upgrades.
I then select Upgrade Itunes.
The system starts to upgrade and download the new software.
It gets to 52.60 MB of 56 MB and then it just freezes / sticks and does not go any further ?
I have tried to upgrade on a number of occasions but the same thing happens each time.
Any help please ?Answer is in the original post.
-
Recently my location bar stopped autocompleting. I cleared my cache but it did not help. it seems to work the first few times when i start Firefox , but then stops. If I quit and restart Firefox, the same thing happens. I have tired checking it after my computer has been shutdown for the night (which I do about once a week), and also after it goes to sleep (which I do frequently).
Don't worry I've sorted it! I just had to turn off Reminders as well in iCloud. Calendar then worked fine, even when I turned Calendar and Reminders back on.
-
The printer is a 6500 E710n-z. It is supposed to support airprint and in fact, did for a day. Now when I try to print an email from my iPad, the messages on the ipad show contacting printer and preparing page. Then nothing. It appears to have sent the email to the printer but nothing shows up in the queue. The only difference between day one and day day was I set up the fax on day two
Hi Dmatt,
I don't have the immediate answer. In case no one comes back with it, here's the Airprint "how-to" doc from Apple with the troubleshooting guide. It may help you untangle the problem spot.
AirPrint setup and troubleshooting
It is my pleasure to assist.
Say “Thanks!” by clicking the Kudos Star to show your appreciation for the help.
Fixed? Mark this Post “Accept as Solution” to help others find the answers.
Note: You can find “Accept as Solution” only on threads started by you.
Kind Regards,
Dragon-Fur -
I bought the first book of three, to test it, but at the next day all thee books went off the store. What happened??
Nobody here can tell you why something like that happens in the iBookstore. Presumably there is some issue between Apple and the publisher. You might try getting what you want from one of the other stores which have free ereaders, like Kindel, Nook, Kobo, Googlebooks, Sony.
-
Hi
Question:
In a hierarchical query, is it possible for a row to have more than one immediate ancestor?
Answer:
No
No? Surely, it's yes?
Thanks,
JasonAs Frank pointed out already hierarhical most often means a tree (data structure) to deal with.
There must usually be just one boss (the root) in which case the answer is no.
Something to read: http://en.wikipedia.org/wiki/Tree_(data_structure)
You can find out Solomon spoke about a generalization therein.
Related to forum troubles:
If I login first thing after reaching forum, the behaviour is rather consistent - I'm allowed to post answers, otherwise ...
Regards
Etbin -
My iPhone does not have Facetime on it. I've tried going into restrictions, but there's a passcode that doesn't seem to be one that I've used before. Is it possible to reset the phone and then just restore a portion of the old information? I've tried several pass codes and now am locked out for an hour after being locked out for 5 minutes and then 15 minutes. It said that I had tried 7 pass codes prior to these, but I don't remember ever trying to get into restrictions before.
I've looked up other posts on this, and my phone was purchased in the US and does not have an AE in the model number.Help for forgotten passcode > iOS: Forgotten passcode or device disabled after entering wrong passcode
When you have access to your iPhone again, FaceTime is a pre installed app that cannot be removed.
Try a search > iOS: Understanding Spotlight Search -
its out of battery and when i plug it in to charge it will charge until it turns on, and then just stops charging?
Try a resetting of your phone just to cover that base - Hold down Home and Sleep buttons for at least 10 seconds and see if the phone powers up.
If the phone was completely dead, powering through wall socket is best approach. I've never been able to charge off of a PC if it was completely dead.
If all fails, bring the phone in for service since it is still covered by warranty. -
My ipad went blank last night for no apparent reason. It was on one minute, and then completely dark. I didn't touch it, it just seemed to have died. I tried turning it back on/off, but nothing happens. Anyone else have a similar situation?
Thansk for the reply King_Penguin...let me elaborate and see what you think...I had the ipad2 in the office and saw the battery was getting really low. I tried charging it with the iphone charger (connects to my pc at work). It took a while, but it got enough juice in the ipad2 to bring it back to life. when I got home, I hooked it up, and got to about 50%. All was fine, then I was attempting to hook it up to my TV with the AV adapter (or VGA adapter, whatever it is), left the ipad alone for a minute, came back to it, and that's when it went dark. I tried the home/sleep buttons, but only for about 5 seconds...any other suggestions in case that doesn't work? Thanks again...
-
Is it possible to buy an iPhone 4s unlocked in the US, and then use it normally and completely into France with Freemobile (which provides micro-SIM) ?
I'm travelling to NYC tomorrow and that would be 100€ less than in France...Thank you for the quick answer
Do you mean that I can't reserve and pick up my phone in the local apple store as it's explained on the site (http://www.apple.com/retail/iphone/) ?
What about the social security number asked in the formulary ? I've got a French one...
Puzzled... -
Ever since the last update, My iTunes continues to quit unexpectedly. It will open for one second and then close. Anyone have a solution for this. Please help.
I've tried my best to troubleshoot. . . opening in safe mode nothing seems to work.
In the problem report, this is the error that stood out:
Crashed Thread: 8 Dispatch queue: com.apple.iad.iadidmanager
Exception Type: EXC_BAD_ACCESS (SIGSEGV)
Exception Codes: KERN_INVALID_ADDRESS at 0x0000000000000090Hi there navicin79,
You may find the troubleshooting steps in the articles below helpful. The first thing I would try is reinstalling iTunes as outlined in the first article.
Troubleshooting iTunes installation on Mac OS X
http://support.apple.com/kb/ht2311
OS X Mavericks: If an app freezes or quits unexpectedly
http://support.apple.com/kb/PH13975
-Griff W. -
i have just downloaded the latest update for Pages on my iPad and now it can no longer open up documents in iCloud and then just shuts down. What The.
Before the reset quit Pages like this:
Double click the Home button to show the screen with running and recently used apps. Each app icon will have a sample page above it. Flick up on the page (not the app icon) and the page will fly away and the app icon will disappear. This quits that app. -
I have moved old Back Up files from my external hard drive to the trash and as the Trash previews the files, i.e. counts them (over 850,000 files) it then begins to delete but then stops. Is it possible to move the files out of the Trash file and then only delete a small amount at one time?
See
Deleting backups via the Finder on Lion 10.7.x or later:
http://pondini.org/TM/12.html
Hold option (alt) while emptying the Trash.
See also
http://pondini.org/TM/E6.html
Message was edited by: WZZZ -
Multicast works for a day and then stops
I'm running multicast in unicast mode on our WLC because I can't enable PIM on wired side yet for a couple reasons. It works consistently on 3 out of 6 WLAN's. And the weird thing is the other 3 WLAN's will work for a day, and when I come in the next day, multicast traffic has stopped flowing. I have verified this through IGMP snooping, using a bonjour browser, testing airplay, and using packet capture on a wireless NIC. 2 of the WLAN's are configured almost identically, but one works consistently day after day, and the other only works for a day after resetting the wlan. I have been coming in the morning and changing a single setting back and forth just to reset the WLAN so it will work for the rest of the day. I'm just writing this to see if someone can think of why it would work fine for the shole day and then stop working by the next morning. It's not an IGMP timeout setting, because it works for much longer than the timeout and behaves the same way even without IGMP snooping on. It started doing this after upgrading to 7.0.240.0. We have very little amount of multicast traffic on wireless, and low channel utilization. It does the same exact thing whether 802.11a or 802.11g so I don't think it has to do with data rates. When I have IGMP snooping on, and on the WLAN's where it's not working, the controller will see the multicast group join message from the client, but the client doesn't see the IGMP query from the controller. It shouldn't be wired config related since it's unicast mode. I've tried with and without broadcasting enabled. Any ideas?
Okay, so I discovered two things, but I still don't know what caused this problem. When I was running 7.0.230.0 I had increased my EAP-Broadcast key interval to 86400 due to a bug. This seems to be related to the fact that on the wlan's where multicast was not working, it stopped by the next day. When I backed this interval down to 3600 the multicast stopped working after an hour instead of a day. So that's why I believe it was somewhat related to the broadcast key, since that key is used for multicast.
What I realized is that multicast was working on all the wlan's on all AP's that had been rebooted since the controller upgrade (They had been rebooted due to a switch losing power). This is weird because all the AP's were rebooted when they received their own 7.0.240.0 software upgrade, so I don't know why they would have needed to be rebooted again. Anyway, I rebooted a few more AP's and multicast works properly on all wlan's on those. I'm just replying to my own thread here in case someone has a similar problem after upgrading your controller - try rebooting all your access points again. Or maybe reboot after changing EAP-Broadcast Key interval. -
Can I set up folders for major classifications of music as opera, country, etc. and then put all the albums with the genre into those folders folders?
Hi Richard Bugdal1,
Welcome to the Support Communities!
You can't change the folder structure within iTunes, but you can easily change the view to sort by Genre.
The link below will explain how to do this:
Apple - Find Out How - Music - iTunes
http://www.apple.com/findouthow/music/itunes.html#tips-viewoptions
Cheers,
Judy
Maybe you are looking for
-
"Error consuming WCF service metadata. Object reference not set to an instance of an object." I have no clue what happen to my BizTalk. I checked all the below forum but m clueless why BTS not consuming WCF through Generated Items. I tried both meta
-
Only 1/3 ipod touch is being recognized by my computer
The others say Unspecified Apple Mobile USB Device. I tried reinstalling iTunes, uninstalling the driver, and unplugging my computer. Help!
-
After connecting Jawbone as headset, internal speakers are no longer usable
Hi everyone, Thanks in advance for the help. Powerbook Aluminum 15 inch 1.67 ghz G4 1 gig Ram 10.5.1 I paired my jawbone to my mac, and it works fine as a headset. When I decided I wanted to turn off the headset, I had a difficult time. I would disco
-
Hi. I have a wee problem. Last week I updated my ipod (4thGen 20gb)with itunes then went to charge it with my power adapter but it wouldn't charge. I then charged it through my laptop as that worked. I tried to use my power adapter a couple of other
-
Parameter screen and report in the same page?????
Hi Gurus... Here is what i am trying to do ..I am trying to show the customization screen and the report in the same page 1.the user selects some data from the lov .. 2.Based on the lov selected field the below report should change .. like if the use