Is it possible to AirPlay an ipad screen(keynote) to multiple appletvs on the same wifi?

Is it possible to AirPlay an ipad screen(keynote) to multiple appletvs on the same wifi?

Thanks - back to the drawing board!

Similar Messages

  • Is it possible to connect an iPad to a SmartBoard and interact with the iPad on the SmartBoard, like you do on a computer with the Smart-software Notebook on it?

    Is it possible to connect an iPad to a SmartBoard and interact with the iPad on the SmartBoard, like you do on a computer with the Smart-software Notebook on it?

    You can purchase an adapter from apple that uses the monitor cable from the projector, its the same one that is probably connecting either your laptop or school workstation. On the projector control you might need to refresh the source.

  • Apple TV 2G (Airplay and Homesharing) can only stream from devices on the same wireless access point range??

    connection:
    40 Mbps Fiber Broadband connection using:
    Devices:
    1. Main Modem/router (AP1): Huawei HG8245 (provided by ISP) - Wireless enabled.
    2. Remote Access point (AP2): Linksys/Cisco E3200 Wireless gigabyte router flashed with DD-WRT v24-sp2 (06/14/11) mini (Cascaded -wired- LAN to LAN from main modem).
    3. Wireless Repeater to cover a dead spot  (AP3): Linksys/Cisco E1000 wireless repeater.
    4. Apple Tv (AT2G) with home sharing/airplay enabled.
    5.( Ipad) with home sharing on itunes enabled.
    6. Win7 (PC) using iTunes with Home sharing enabled.
    all devices are updated to their latest firmware.
    In order to cover a large 3 story house with Wifi. I had (AP1) is located on the first floor, while (AP2) is located in the basement floor directly wired by LAN to LAN with (AP1). (AP3) is located on the Ground floor away from the living room to repeat wireless network into the back yard. While (AT2G) is located in the living room on the ground floor right in the middle of both (AP1) + (AP2) while connected via Wifi.
    Network SSID, security, passphrase and wireless settings of (AP2) are identical to (AP1) to create a single big LAN/WLAN roaming network where all devices connected to both wireless access points can find/share the others. As understood, it's refered to as bridging.
    I have noticed that my iphone/ipad does not show the airplay button anywhere within the wireless network. it seems that the apple TV randomly choses to connect to the AP with stronger signal, or switch to the other in case of a reboot to one of them.
    to elaborate further, if i was sitting in the living room (groundfloor), trying to airplay some you tube contents via Wifi to my Apple TV, i may not find the airplay button available all the time, i found out the reason is while i'm wirelessly connected to AP1, the Apple TV was connected to AP2 and both deviced cannot detect each others to enable my purpose. that goes the same for Home Sharing. only if my Ipad/PC and Apple Tv are on the same wireless AP. they would detect each others immediately.
    although, the second AP (AP2) is suppose to extend my wireless network of the same subnet in which any device connected can be found.
    After all sorts of trial and error tweaking my router/access point, I thought the problem would be due to the Linksys 3200 capability of bridging WLAN and lacks few protocols that enables my purpose. i have flashed the firmware to a DD-WRT, but again, problem was not solved.
    I have not tried having my Apple Tv wired to either router/AP, but i assume it may work well if i do so. i still need to solve this wireless connection issue though.
    Am i the only one with this problem, would there be something wrong with my setup? 
    Your feedback is highly appreciated.

    You may or may not already have your network set up correctly, it's just that I can't tell from what you have said.
    I have a main router provided by my ISP, I have several other Airport Extremes and Airport expresses connected by Ethernet, all set up to bridge the network created by the main router.
    Each maker has their own settings, but bridging should be reasonably obvious. In simple terms my main router distributes IP addresses to all devices, the Airports bridge that network by passing these addresses to the devices from the main router. A base station that isn't in bridging mode will distribute its own addresses to the devices connected to it.
    I don't really follow your next point.
    instruction for configuration vary from manufacturer to manufacturer, the best course of action here is to refer to the manual. If everything is set up properly the addresses of everything on your network will have identical sets of numbers for the first 3 of 4 groups of numbers that make up an address, the last set must always be different. I think the part you are referring to with your DD-WRT is the option to have Ethernet and wifi bridged or not.
    Some routers may be easier to configure than others, but generally speaking they should all work with the Apple TV. 5Ghz is less likely to suffer interference but it is much more likely to be blocked by solid objects, it may or may not be an advantage.

  • I just bought an Apple TV and I'm trying to connect airplay but the icon does not appear! My iPhone and Apple TV are on the same wifi connection but the airplay button does not apper?

    I just bought an Apple TV and I'm trying to connect airplay but the icon does not appear! My iPhone and Apple TV are on the same wifi connection but the airplay button does not apper? The same thing with my iPad mini

    Try restarting all devices including portable  iOS ones and your router.
    Check Airplay is not disabled in AppleTVs settings.
    AC

  • I have an ipad 2 and it constantly buffers on I players such as itv and 4od. I have an iPhone 5 and on the same wifi it's perfectly fine yet my ipad won't play. Any ideas??

    I have an ipad 2 and it constantly buffers on I players such as itv and 4od. I have an iPhone 5 and on the same wifi it's perfectly fine yet my ipad won't play. Any ideas??

    Hi,
    Have you tried a reset?
    This solves a lot of these problems, and I'm not sure if this will work in your case, but give it a try. You hold down the sleep and home buttons at the same time. A slider will appear. Ignore it and keep holding both buttons down. After about 15 seconds the Apple logo will appear. See if that helps.
    You will not lose anything on your ipad when you do a reset. (A restore is a whole other issue!)
    The following link addresses your issue and offers some other possible solutions.
    http://everydaylife.globalpost.com/fix-slow-streaming-ipad-27814.html
    Hope this helps.

  • My ISP requires a http login. I can use the iPad fine if I am logged in on a PC connected to the same wifi network, but if I login on safari on my ipad, the connection drops after some time.. any workaround?

    My ISP requires a http login. I can use the iPad fine if I am logged in on a PC connected to the same wifi network, but if I login on safari on my ipad, the connection drops after some time.. any workaround?

    TJBUSMC1973 wrote:
    The iPhone is working, as designed and advertised.  In this case, the user failed to educate themselves properly, either by proper research or asking the right questions, before purchasing the device.
    I understand that the OP failed to do research. But then, I wasn't replying to the OP. I was replying to Chris. I have Verizon. I can talk and use data at the same time with my Droid Maxx. Therefore, the problem is not just with the network. It would be technically possible for an iPhone to do that on Verizon/Sprint if Apple had chosen to use a different chip, such as the kind other phone manufacturers have elected to use.
    Of course, this is probably all irrelevant to the OP's issue. It was merely a point of clarification, especially for those people who are used to being able to use both voice and data at the same time on Verizon. When they switch to an iPhone, they are often surprized at the limitation.
    Best of luck.

  • Is the ipad 1 able to run and download the same apps as the ipad 3

    Is the ipad 1 able to run and download the same apps as the ipad 3

    You have to look at the system requirements for the app. the iPad 1 cannot run a version of iOS higher than 5.1.1. If the app requires a higher veriosn, you cannot run it.
    System reqs for any app in the itunes store are at the left edge of the screen.
    Fortunately most apps still run on the older iOS version

  • My iPad Air always freezes during FaceTime calls using wifi. I switch to my iPhone 5c on the same wifi, and it never freezes while I'm sitting in the same location. Is there maybe a setting I have that is causes this? I am un to date on the OS also.

    My iPad Air always freezes during FaceTime calls using wifi. I switch to my iPhone 5c on the same wifi, and it never freezes while I'm sitting in the same location. Is there maybe a setting I have that is causes this? I am up to date on the OS 7.1.1. Video and audio is froze on my end, only video freezes on the other end. It doesn't make a difference who makes the call either.

    No, there isn't any setting that you are missing. Have you tried force closing FaceTime, and resetting your iPad?
    In order to close FaceTime, you have to drag the app up from the multitasking display. Double tap the home button and you will see apps lined up going left to right across the screen. Swipe to get to the app that you want to close and then swipe "up" on the app preview thumbnail to close it.
    Reset the iPad by holding down on the sleep and home buttons at the same time for about 10-15 seconds until the Apple Logo appears - ignore the red slider if it appears on the screen - let go of the buttons. Let the iPad start up.
    If that does not make a difference, you could try resetting all settings, if you reset all settings you will have to enter all of the device preferences again in the settings app. That takes some time to accomplish, but you will not lose my data, media, apps or anything like that. Settings>General>Reset>Reset all settings.
    If that doesn't help, the next step would be to restore the iOS software. Backup your iPad first, restore the iOS, then restore the backup.
    Use iTunes to restore your iOS device to factory settings

  • HT4972 When I take photos of myself, the image come out backwards.  I have an iPad2 and an iPad 3, and both of them do the same with my self portraits.  Any ideas on how to remedy this?

    When I take photos of myself, the image come out backwards.  I have an iPad2 and an iPad 3, and both of them do the same with my self portraits.  Any ideas on how to fix this.  I use wifi.

    Gmabert-
    The front camera displays a reversed image on the screen, as if you were looking into a mirror.  When you take a picture, it comes out normal, which is backwards to what you would have observed on the screen.
    Fred

  • Can i transfer everything from one ipad to another so both have exactly the same things

    Can i transfer everything from one ipad to another so both have exactly the same things?

    Yes. Copy your apps and other iTunes purchases/downloads to your computer's iTunes via File > Transfer Purchases (File > Devices > Transfer Purchases if you have iTunes 11 on your computer), then backup up the first iPad and restore that backup onto the second iPad.
    Backups and restores : http://support.apple.com/kb/HT4079
    Things that aren't included in a backup include the contents of the Music and Videos apps (but they should be on your computer's iTunes) and photos that were synced from a computer. Also you will need to enter your passwords (email, wifi, website) on the second iPad - they won't be restored onto a different device, only back onto the device that the backup came from.

  • Is it possible to use both an ILB and an ELB (listening on the same port) in the same Azure cloud service?

    I'm building a test Lync deployment on Azure; yes, I know this is not supported, hence "test".
    Lync Front-End servers expose two set of web services, one for internal users and one for external ones; they listen on different ports (443 and 4443) on the same servers; when external services are published, you need a reverse proxy or a port forwarding
    in order to map port 443 of a public IP address to port 4443 of the Front-End server(s). When you have multiple Front-End servers in a pool, you also need to load-balance them.
    So, a typical Lync deployment looks like this:
           Internal users
                     |
                   443
                      |
              Internal LB
            192.168.0.20
            443         443
              |               |
       Lync FE 1     Lync FE 2
    192.168.0.21 192.168.0.22
              |               |
          4443        4443
              External LB
           Public IP Address
                     |
                  443
                     |
           External Users
    This should be easily replicated in Azure, as it supports both external load balancing and internal load balancing. They are even supported together in the same cloud service, so this configuration should be easy. However, it looks like "should"
    is the keyword here.
    After creating the external load balanced endpoint (which listens on external port 443 and forwards to port 4443 on the servers), I'm trying to create an internal load balancer and add internal endpoints to is; however, while the ILB can be created successfully,
    adding an internal endpoint listening on port 443 and forwarding to port 443 on the servers fails miserably, with an error stating that port 443 is already in use by another endpoint:
    Update-AzureVM : BadRequest : Port 443 is already in use by one of the endpoints in this deployment. Ensure that the port numbers are unique across endpoints within a deployment.
    For reference, my commands are:
    Add-AzureInternalLoadBalancer -InternalLoadBalancerName "LyncILB" -ServiceName "LyncFrontEnd" -SubnetName "LabSubnet" -StaticVNetIPAddress 192.168.0.20
    (This completes successfully)
    Get-AzureVM LYNCFE1 | Add-AzureEndpoint -Name "Https-Int" -Protocol "tcp" -LocalPort 443 -PublicPort 443 -LBSetName "HttpsIntLB" -DefaultProbe -InternalLoadBalancerName "LyncILB"
    (This fails)
    The existing external endpoint is configured as such:
    Get-AzureVM LYNCFE1 | get-azureendpoint
    LBSetName : HttpsExtLB
    LocalPort : 4443
    Name : HTTPS-Ext
    Port : 443
    Protocol : tcp
    Vip :
    ProbePath :
    ProbePort : 4443
    ProbeProtocol : tcp
    ProbeIntervalInSeconds : 15
    ProbeTimeoutInSeconds : 31
    EnableDirectServerReturn : False
    Acl : {}
    InternalLoadBalancerName :
    IdleTimeoutInMinutes :
    LoadBalancerDistribution :
    The error doesn't even make a lot of sense; the external load balancer listens on a public IP address, while the internal load balancer listens on a private IP address in the internal network; there
    shouldn't be any conflict here... however it looks like there is one instead.
    Why doesn't this work? Am I doing something wrong, or is Azure networking just being silly as usual again?

    Hello Massimo Pascucci,
    The issue that you are facing when creating an endpoint with internal loadbalancer is the limitation of not allowing same ports to be listening under a single cloud service. This reason for this is that there is a limitation of only one private IP (Also
    known as the Internal load balanced IP) per cloud service.
    There is also a limitation on the Internal load balancer more than one port to be published per load balancer:
    You can leave your feedback by following the link below:
    https://social.msdn.microsoft.com/Forums/en-US/1805c5a0-3906-4cd6-8561-9802d77e0ae5/is-it-possible-to-use-both-an-ilb-and-an-elb-listening-on-the-same-port-in-the-same-azure-cloud?forum=WAVirtualMachinesVirtualNetwork
    Refer to this article for more information on Internal load balancer:
    http://azure.microsoft.com/blog/2014/05/20/internal-load-balancing/
    Thanks,
    Syed Irfan Hussain

  • I keep getting message "mozila Firefox not responding." It takes minutes to down load a site - some times it just gets in a loop and never down loads. Then when I try to click on it again screen goes opaque and i get the same message.

    I 'm getting message "Mozila Firefox not responding." It takes minutes to down load a site - some times just gets in a loop and never down loads. The little circle at top just keeps going round in circles .
    Then when I try to click on the screen again the screen goes opaque and I get the same message re " Mozilla Firefox not responding" - and it is minutes before I can get back in to close down screen.
    I have downloaded Fire fox version 4 and this is still happening.

    See:
    * http://kb.mozillazine.org/Error_loading_websites

  • Safari and Firefox on my desktop suddenly stopped combine ting to any website.  IPad and IPhone work fine from the same wifi. Any ideas.

    Safari and Firefox will not connect to website On desktop. IPad and IPhone work fine from the same wifi.

    Restart your router.

  • HT201363 My iPhone, iPad and iPod are all associated with the same Apple ID.  How can I remove the iPod and associate it with a new Apple ID without affecting the data on the other devices (note: there is no data on the iPod I want to keep)?

    My iPhone, iPad and iPod are all associated with the same Apple ID.  How can I remove the iPod and associate it with a new Apple ID without affecting the data on the other devices (note: there is no data on the iPod I want to keep)?

    Very simple.  Turn off Find my iDevice, then  Tap Settings, General, Erase, Erase all content and settings.

  • I have an iPhone 5 an iPad and iPhone 4S all connected to the same apple ID, but for iMessage for some reason it uses my husbands phone number

    I have an iPhone 5 an iPad and iPhone 4S all connected to the same apple ID, but for iMessage for some reason it uses my husbands phone number

    Using FaceTime http://support.apple.com/kb/ht4319
    Troubleshooting FaceTime http://support.apple.com/kb/TS3367
    The Complete Guide to FaceTime + iMessage: Setup, Use, and Troubleshooting
    http://tinyurl.com/a7odey8
    Troubleshooting FaceTime and iMessage activation
    http://support.apple.com/kb/TS4268
    Using FaceTime and iMessage behind a firewall
    http://support.apple.com/kb/HT4245
    iOS: About Messages
    http://support.apple.com/kb/HT3529
    Set up iMessage
    http://www.apple.com/ca/ios/messages/
    Troubleshooting Messages
    http://support.apple.com/kb/TS2755
    Setting Up Multiple iOS Devices for iMessage and Facetime
    http://macmost.com/setting-up-multiple-ios-devices-for-messages-and-facetime.htm l
    FaceTime and iMessage not accepting Apple ID password
    http://www.ilounge.com/index.php/articles/comments/facetime-and-imessage-not-acc epting-apple-id-password/
    Unable to use FaceTime and iMessage with my apple ID
    https://discussions.apple.com/thread/4649373?tstart=90
    For non-Apple devices, check out the TextFree app https://itunes.apple.com/us/app/text-free-textfree-sms-real/id399355755?mt=8
     Cheers, Tom

Maybe you are looking for