Is it possible to configure an SNMP copmmunity string on an ATA 186 without accessing it via console?

I am trying to configure a particular SNMP community string on many ATAs for a Cisco 'Know the Network' project. On a Cisco ATA 186, you cannot telnet or SSH to it and the only way to remotely change the parameters are via the web GUI, which doesn't have the SNMP field available.
Is this possible without getting physical console access to the ATA?

No.
An ASA can, as you noted, restrict source and destination IP and port. To do what you are asking, one would need to prevent a string within the payload from being transmitted (or only accept certain strings).
You should just put the access-list on the destination device(s) restricting what host(s) are allowed snmp rw (as you alluded to). That's a very common implementation straight out of the textbook.

Similar Messages

Is it possible to to disconnect 2 wireless clients from my wireless network without access to the clients i.e. 2 iPads?

Is it possible to disconnect 2 wireless clients from my network if I do not have access to the clients? ie 2 iPads.

You would have to set up Timed Access for each device.
This consists of specifying the amount of time each day that wireless devices will be allowed to connect to the network. You must provide a MAC or hardware address for each device, which is a long code that might look something like this, for example......A1-B2-C3-D4-E5-F6....and then specify the hours each day that this device is allowed to connect to the wireless network.
You have to do this for each device, which is tedious. Devices that are not on the Access List cannot connect to the network at any time.

I have a problem with Mail on my Macbook Pro. It is configurated with a gmail account, and now I can't access the mail. Is it possible to reboot the account or..? Please help:)

I have a problem with Mail on my Macbook Pro. It is configurated with a gmail account, and now I can't access the mail. Is it possible to reboot the account or..? Please help:)

The question mark means the computer cannot find a bootable volumes so can;t do anything, That, combined with annoying sounds, strongly suggests a failed hard drive.
You can ask a "genius" at an Apple Rtail Store to test it but I'm pretty sure the drive is kaput. I'm hoping you had your data backed up.

Is it possible to configure a smartform in QGA3 instead of the standard script QM_INSP_RESULT.

Is it possible to configure a smartform in QGA3 instead of the standard script QM_INSP_RESULT.

Hello ,
I'm afraid not , the program for the transaction is admitting only Sapscript format , even the BADI
QG_INSP_RESULT_PRINT allow to switch to a SAPscript form
Regards

Possible to configure per connection timeout values?

hi,
please, does anybody know how (or whether or not it is even possible) to configure a "PER CONNECTION" timeout on the connections - created by jndi - to an ldap server?
my understanding is that setting the "com.sun.jndi.ldap.connect.timeout" property on the javax.naming.directory.InitialDirContext sets a _global_ timeout value for _all_ connections created/managed by that InitialDirContext (that is, with a "PER CONTEXT" scope).
however, what i would like to do instead, is somehow configure a different timeout value for each individual connection that a InitialDirContext might know about.
the first solution that will probably pop in your head is "connection pool". however, the app sets "java.naming.ldap.factory.socket" property to a custom socket factory class. according to the following paragraph from the jndi tutorial, that disqualifies the app from using connection pools:
"There are a couple of environment properties that automatically disqualify a Context instance from using a pooled connection. A Context instance cannot use a pooled connection if it has its "java.naming.ldap.factory.socket" property set to a custom socket factory class, or its "java.naming.security.sasl.callback" property set to a custom callback handler class, or its "com.sun.jndi.ldap.trace.ber" property set to enable protocol tracing."
http://java.sun.com/products/jndi/tutorial/ldap/connect/config.html
even if we could use connection pools, we still wouldn't be able to set "per connection" timeout values. would we?
one proposed solution is to completely rip out jndi from the app and replace it with the netscape directory sdk for java. to me, that seems like too drastic a measure though - given the project's time-constraints (the way the app was originally designed does not lend itself to a straight-forward "pop-out/drop-in" type replacement). i was hoping there would be a simpler alternative (a jndi-based configuration type solution, for example).
any suggestions would be gratefully appreciated. thanks in advance for your replies.

Enable the Default Host option in the AirPort Admin Utility, use the IP address you have assigned to your server.

Is it possible to configure Outlook 2010 as the Default Mail client if it is presented to the Desktop via RemoteApp?

I am a user of RemoteApps. I connect to a Website that presents me with various applications, include Outlook 2010. however, I use other programs that I need to send mail from that are in within the RemoteApp workspace. Is it possible to configure windows
7 to map a call to RemoteApp/Outlook2010 to send mail as a default mail client? or Perhaps a way to get OWA to map as a default mail client handler?
I am using Windows 7 SP1 - Updated to latest service releases, Outlook 2010 from RemoteApps, and IE 11.
Thank you in advance!

Hi Raymond,
Based on my research, we can use Group Policy and Internet Options to configure default mail client.
How to make Outlook the default mail client
http://support.microsoft.com/kb/223877/en-us
How to configure the default e-mail client using Group Policy
http://support.microsoft.com/kb/2008044
Best Regards,
Amy
Please remember to mark the replies as answers if they help and un-mark them if they provide no help. If you have feedback for TechNet Subscriber Support, contact [email protected]

Vmware wsx is it possible to configure language for keyboard like AZERTY ?

vmware wsx seems to be wonderful application for the future
but it is possible to configure keyboard for differents countries like French...

You should ask this on https://mail.mozilla.org/listinfo/mobile-firefox-dev instead of a end user forum. It may require building a custom APK of Firefox.

Is it possible to configure IDOC with Business service

hi
Is it possible to configure IDOC with Business Service
Thanking you....
aravind...........
<Interview question locked, please read the [Rules of Engagement|https://wiki.sdn.sap.com/wiki/display/HOME/RulesofEngagement]>
Edited by: Mike Pokraka on Sep 18, 2008 9:25 AM

Hi Chary,
Check this
https://www.sdn.sap.com/irj/sdn/go/portal/prtroot/docs/library/uuid/e07dcaa0-a92b-2a10-3a96-b3d942bd1539
Regards
Seshagiri

ACE: Problem configuring probe snmp

Hi,
I have a problem when I configure probe snmp and My Server W2K3 dual core, snmp comunity public has an oid cpu .1.3.6.1.2.1.25.3.3.1.2, the output is:
access-list anyone line 8 extended permit ip any any
probe snmp was
interval 4
faildetect 2
passdetect interval 10
receive 2
community public
oid .1.3.6.1.2.1.25.3.3.1.2
threshold 70
rserver host was1
ip address 10.24.8.200
probe was
inservice
rserver host was2
ip address 10.24.8.201
probe was
inservice
serverfarm host servers
rserver was1
inservice
rserver was2
inservice
class-map type management match-any ADM-CONTEX-SERV1
4 match protocol icmp any
5 match protocol snmp any
class-map type http loadbalance match-all Check-Headers
2 match http url .*
3 match http header Host header-value "10.24.16.*"
4 match http header User-Agent header-value ".*MSIE.*"
class-map match-all VIP-10-HTTP
2 match virtual-address 10.24.16.10 tcp eq www
class-map type http loadbalance match-all other-HTTP
2 match http url .*
policy-map type management first-match ADM-CTX-SERV1
class ADM-CONTEX-SERV1
permit
policy-map type loadbalance first-match L7-logic
class Check-Headers
serverfarm servers
class other-HTTP
serverfarm servers
policy-map type loadbalance first-match lb-logic
class class-default
serverfarm servers
policy-map multi-match client-vips
class VIP-10-HTTP
loadbalance vip inservice
loadbalance policy L7-logic
loadbalance vip icmp-reply active
interface vlan 60
ip address 10.24.8.5 255.255.255.0
access-group input anyone
access-group output anyone
service-policy input ADM-CTX-SERV1
no shutdown
interface vlan 233
ip address 10.24.16.5 255.255.255.0
access-group input anyone
access-group output anyone
service-policy input ADM-CTX-SERV1
service-policy input client-vips
no shutdown
ip route 0.0.0.0 0.0.0.0 10.24.16.1
sh probe was detail
probe : was
type : SNMP
state : ACTIVE
description :
port : 161 address : 0.0.0.0 addr type : TRANSPARENT
interval : 4 pass intvl : 10 pass count : 3
fail count: 2 recv timeout: 2
version : 1 community : public
oid string #1 : .1.3.6.1.2.1.25.3.3.1.2
type : PERCENTILE max value : 100
weight : 16000 threshold : 70
--------------------- probe results --------------------
probe association probed-address probes failed passed health
------------------- ---------------+----------+----------+----------+-------
rserver : was1
10.24.8.201 13 13 0 FAILED
Socket state : CLOSED
No. Passed states : 0 No. Failed states : 1
No. Probes skipped : 0 Last status code : 0
No. Out of Sockets : 0 No. Internal error: 0
Last disconnect err : Server reply - bad SNMP OID
Last probe time : Tue Feb 24 23:22:41 2009
Last fail time : Tue Feb 24 23:20:47 2009
Last active time : Never
Server load : 16000
rserver : was2
10.24.8.200 12 12 0 FAILED
Socket state : CLOSED
No. Passed states : 0 No. Failed states : 1
No. Probes skipped : 0 Last status code : 0
No. Out of Sockets : 0 No. Internal error: 0
Last disconnect err : Server reply timeout (no reply)
Last probe time : Tue Feb 24 23:22:34 2009
Last fail time : Tue Feb 24 23:20:52 2009
Last active time : Never
Server load : 16000

Hi,
For a multicore processor you need to make a few changes to get the load on each core/processor. You need to have an instance for each core.
Try adding .1 or .2 to the OID to get the load on each core.
Also try doing an snmpwalk on the OID to see what the real structure is.
HTH
Cathy

Is it possible to configure Webdynpro in Netweaver ABAP/JAVA trial version.

Hai, all
Can anyone clear me that, is it possible to configure Webdynpro in Netweaver ABAP and Netweaver JAVA trial versions.

Hello Senthil ,
It possible to configure Webdynpro in Netweaver ABAP trial version.
SAP NetWeaver 7.0 ABAP Trial Version (incl. Web Dynpro ABAP) is available on SDN Download .
<a href="https://www.sdn.sap.comhttp://www.sdn.sap.comhttp://www.sdn.sap.com/irj/sdn/downloaditem?rid=/library/uuid/cfc19866-0401-0010-35b2-dc8158247fb6">to Download !</a>
Regards ,
Santosh

Is it possible to configure Webdynpro in Netweaver ABAP/JAVA trial vers

Is it possible to configure Webdynpro in Netweaver ABAP/JAVA trial version.

Hello Senthil ,
It possible to configure Webdynpro in Netweaver ABAP trial version.
SAP NetWeaver 7.0 ABAP Trial Version (incl. Web Dynpro ABAP) is available on SDN Download .
<a href="https://www.sdn.sap.comhttp://www.sdn.sap.comhttp://www.sdn.sap.com/irj/sdn/downloaditem?rid=/library/uuid/cfc19866-0401-0010-35b2-dc8158247fb6">to Download !</a>
Regards ,
Santosh

Is it possible to configure CF10 or CF11 to use Xerces XML parser instead of Saxon XML parser?

Could anyone tell me if it is possible to configure CF10 or CF 11 to use the older Xerces XML parser instead of the Saxon XML parser.
I am in the process of migrating a website from CF8 to CF11. Several sections rely on XML transformation, which no longer work in CF11. After investigating the problem it seems to be that the Saxon Parser is more strict, causing these errors.

Well I guess Parsers would be better solution. As u said u need to insert node at specific location.
so now u have to decide which parser u need to choose according to u r requirmnet. DOM or SAX maily.
Both has adv and di-advs.
...yogesh

Possible to configure HLS segments with different URL than governing M3U8 playlist?

Currently we have 4 AMS servers with VOD applications for RTMPe and HLSe. These are load balanced by round-robin DNS, such that any request to VOD content could hit one of 4 servers depending on the DNS record served (DNS TTL=5mins).
RTMPe works fine 100% of the time. We are having intermittent issues with HLSe and IOS devices in that randomly the stream will stop in our player (Brightcove based). Player logs seem to indicate requests to HLSe segments showing as not found/error when the content freeze occurs.
My initial guess is that requests to VOD content may come from one AMS server and contain segment URLS also based on the DNS round robin hostname, then potential mid-playlist the DNS updates and you request the next segments from another server, potentially causing issues(??).
e.g.
Playlist:
http://DNS-RR-HOSTNAME/mycontent.m3u8 - DNS resolves to AMS01, playlist served by AMS01
Segments:
http://DNS-RR-HOSTNAME/mycontent-seg01.ts - served by AMS01
http://DNS-RR-HOSTNAME/mycontent-seg02.ts - served by AMS01
http://DNS-RR-HOSTNAME/mycontent-seg03.ts - served by AMS01 (DNS flips to AMS02).
http://DNS-RR-HOSTNAME/mycontent-seg04.ts - served by AMS02
http://DNS-RR-HOSTNAME/mycontent-seg05.ts - served by AMS02
Could this situation potentially cause player to halt playout? Is it possible to configure AMS to serve the HLS segments using a different hostname, whilst still being able to serve the playlist from the DNS RR hostname. This way the playlist would return a list of segments direct from the server that served the initial playlist. e.g.
Playlist:
http://DNS-RR-HOSTNAME/mycontent.m3u8 - DNS resolves to AMS01, playlist served by AMS01
AMS01 serves segments with hostname of itself only:
Segments:
http://AMS01-DIRECT-HOSTNAME/mycontent-seg01.ts
http://AMS01-DIRECT-HOSTNAME/mycontent-seg02.ts
http://AMS01-DIRECT-HOSTNAME/mycontent-seg03.ts
http://AMS01-DIRECT-HOSTNAME/mycontent-seg04.ts
http://AMS01-DIRECT-HOSTNAME/mycontent-seg05.ts
Playlist:
http://DNS-RR-HOSTNAME/mycontent.m3u8 - DNS resolves to AMS02, playlist served by AMS02
AMS02 serves segments with hostname of itself only:
Segments:
http://AMS02-DIRECT-HOSTNAME/mycontent-seg01.ts
http://AMS02-DIRECT-HOSTNAME/mycontent-seg02.ts
http://AMS02-DIRECT-HOSTNAME/mycontent-seg03.ts
http://AMS02-DIRECT-HOSTNAME/mycontent-seg04.ts
http://AMS02-DIRECT-HOSTNAME/mycontent-seg05.ts

the link http://localhost/awstats/awstats.pl started opening.
the problem was the permission of the directories in /usr/share/webapps/awstats/ i changes 755 then it started working

It is not possible to configure the selected XI domain

Hi...
PI 7.0 server on Windows environment and database is SQL Server.
PI Server pick and place the messages from r/3 to r/3 in Oneway but in the reverse it is pick the messages from source but it is not place to the target system.
The error messsage in RWB in end to end monitoring...
It is not possible to configure the selected XI domain because the Integration Server does not exist or could not be read from the SLD
In Component monitoring...
500 internal server error
Application error occured during repuest processing..
Thnx
Raj

Thanks for your promp response, tbluong.
The configuration in SXMB_ADM > Integration Engine Configuration is already done and its check (F7) returns success (all green): "Role of Business System: Current Configuration = System Landscape" and "Corresponding Integration Server: Current Configuration = System Landscape".
Any suggestion?
Regards.

Possibility to configure Freedome VPN connection on unsupported devices

I have this idea, which I think would be useful in this world of many different OSes:
I suggest that you would make it possible to, for example, configure the VPN connection on Windows Phone. Windows Phone has the possibility to configure VPN profiles at the settings, and so do many other OSes that are not supported by Freedome. This would also solve the problem of having no VPN on Linux. Of cource it wouldn't be as easy as pressing a big button, but many privacy-aware users would benefit from it.

Hi Jay,
So, when you say you need to connect your website to your Local Network, is your website a Paas instance or a IaaS instance, i.e., website hosted in a VM using IIS?
Do you have a single instance of the website or multiple instances that have been added to a VNET and need to be connected to the On-Premise Network?
What VPN device are you using to connect Azure to On-Prem?
If you have one website instance that needs to connect to an On-prem network Point-to-Site (P2S) connection would make sense. However, if you have multiple instances of your website in a VNET you would need a Site-to-Site (S2S) connection.
Please be advised that only devices that support Dynamic Routing Gateway would work when configuring P2S connections.
Regards,
Malar.

Is it possible to configure an SNMP copmmunity string on an ATA 186 without accessing it via console?

Similar Messages

Maybe you are looking for