Is it possible to Configure VPC Between N5010 and 6513
Hello Gents,
Please let me know if we can configure VPC Between N5010 and 6513(coreswitch).
IF Yes, Does it have any loops or abnormal traiffc behaviour ?
Please refer the attached mail for current network diagram
1) I would like to establish VPC Between N5010 and Cisco 6513 switch
2) if yes, Does the upstream devices above 6513 core switch will forward the traffic from all the
6513 ports connected to N5000 ports or 6513 will send traffic from one up link and block other
uplink ports as part of STP.
3) Is VSS on 6513 is required for Point #1
Please refer some links on this as well.
Appreciate your quick response.
Thanks and Regards,
KA.
Hi Karim ,
You can use this one - you can consider your 6k the FEX as in this example
http://www.cisco.com/en/US/prod/collateral/switches/ps9441/ps9670/configuration_guide_c07-543563.html
On the portchannel to 6k will not configure :
"switchport mode fex-fabric"
"fex associate 100"
This configuration in indended to be used with FEX.
Regards
Dan
Similar Messages
-
Is it possible to transfer music between iPhones and iPods with out using iTunes
Is it possible to transfer music between iPhones and iPods with out using iTunes
Nope. Both require iTunes on a computer to sync music from.
Unless the iPod is an iPod Touch and the music was bought from iTunes. In which case the Touch can simply go to the iTunes App, under Purchased and download the purchased songs for free. -
What are the configuration need between R3 and XI when we use RFC sync adap
hi,
What are the configuration need between R3 and XI when we use RFC sync adapter.
Regards
siva.if its the sender adapter ref:
RFC adapter
Sender- /people/michal.krawczyk2/blog/2005/03/29/configuring-the-sender-rfc-adapter--step-by-step
Receiver;
http://help.sap.com/saphelp_nw04/helpdata/en/c8/e80440a832e369e10000000a155106/content.htm
Also;
trouble shooting rfc/soap -
/people/shabarish.vijayakumar/blog/2008/01/08/troubleshooting--rfc-and-soap-scenarios-updated-on-20042009 -
How to configure SingleSignOn between GRC and BOBJ 4.1
How to configure SingleSignOn between GRC and BOBJ 4.1?
We have configured the System entitlement in BOBJ CMC. But didn't do anything on the GRC system.
User can login from BOBJ to GRC with password but not with SSO.
We haven't configured SNC . I don't this for this simple flow, we need to have SNC.
We haven't set up the Trust certificate exchange as well between BOBJ and GRC.
Please help us to know what are the mandatory settings need to be done to create a Relational connection for a ERP/GRC system from BOBJ client tool IDT?
thanks,
TilakHow to configure SingleSignOn between GRC and BOBJ 4.1?
We have configured the System entitlement in BOBJ CMC. But didn't do anything on the GRC system.
User can login from BOBJ to GRC with password but not with SSO.
We haven't configured SNC . I don't this for this simple flow, we need to have SNC.
We haven't set up the Trust certificate exchange as well between BOBJ and GRC.
Please help us to know what are the mandatory settings need to be done to create a Relational connection for a ERP/GRC system from BOBJ client tool IDT?
thanks,
Tilak -
Is it possible to sync numbers between iPad and iPhone and mac
Is it possible to sync Numbers between iPhone and iPad and IMac. I work in a school and want to keep test scores for my class in the one place without having to manually update the spreadsheets each time I enter scores.
Thanks in advance
ConorYes, Numbers syncs (very well) via iCloud. You need to activate Numbers iCloud sync on all of your devices.
On the Mac, go to System Preferences > iCloud and make sure Documents & Data is checked. Also click the Options... button next to Documents & Data and check Numbers.app.
On each iOS device, go to Settings > iCloud > Documents & Data > and turn on Numbers. Also go to Settings > Numbers and turn on Use iCloud.
After you've got things working, it's best to close down the Numbers document on one device before you use it on another.
SG -
Running HSRP between N5k 's and vPC between N2k and server
Dear All,
I have the following existing setup, i would like to run HSRP between N5k1 and N5k2. Also would lilke to run vPC between N2k1,N2k2 to the server farm which are dual homed. Please find the diagram attached.
Please advise the step by step process along with the commands to be entered. Thanks for your helpHi,
If you don't have many vlans, there is no need to load balance. Make one of the 5ks the primary for HSRP and the other one stand-by.
here is good link on how to configure it. Make sure to run HSRP version 2. This way you can mach the HSRP group IDs with your vlan IDs. Also give a higher priority to the active 5k and enable preemption.
http://www.cisco.com/c/en/us/td/docs/switches/datacenter/nexus5500/sw/unicast/7_x/cisco_n5500_layer3_ucast_cfg_rel_6x/l3_hsrp.html
HTH -
Key Configuration differences between SAP and ORACLE Financials
Hello,
After spending good 7 years in SAP related projects recently I started working in ORACLE Applications. I used to be an ORACLE programmer years back. To my surprise the same <b><u>ORACLE Forms</u></b> are still very much the heart of the ORACLE UI.
Then I thought what will be the key differences between ORACLE and SAP in terms of configuration elements. While I know a bunch of configuraion items in SAP , I am not sure about the same in ORACLE world. I am not even sure some of the configuration items that are available in SAP exists in ORACLE.
Does anyone know both sides of the coin ? The terminology and design ?
SAP has
Client,Company code, Business area, Functional Area, GL, Posting Key, Document Type.
I am trying to get the details of the equivalents of these in ORACLE.
Does anyone know it ?
For e.g , when you post to <b>AP</b> or <b>AR</b> in <b>SAP</b> , <b>GL</b> is updated automatically. In <b>ORACLE</b> you post to a <b>AP Book</b> or <b>AR Book</b> then Run a batch to move them to <b><u>GL Book</u></b>.
ORACLE uses SQLLoader to load data . You can write a PL SQL and update the tables directly, which is not the case in SAP. For dataloads and conversions, SAP uses BDC's ( though XI can be used but its slow).For ORACLE its the good old SQL and PlSQL combo.
What are the equivalents of the configuration elements in ORACLE world ?
Also what are the major differences between these two in terms of designing a financial system.
Does any one know ?Genie,
I agree that a case is made on how well these two ERPs solve the day to day tasks before a company chooses one of these two. But my question is aimed at finance to begin with. You are going to need a general ledger for any company or government regardless of ERP. And how well you can drive the ledger to map your business is the key here.
The way ledger is built is around a business area ,company or country and is very tighly designed in SAP. I would like to know if there is any equivalent of the configuration items in ORACLE. I am more interested in terminology of ORACLE.
For example ,
<u><b><u><b>SAP ====> ORACLE</b></u>
<u><b>GL ==> Book In ORACLE</b></u>
<b><u>Document Number ===> Invoice Number</u></b>
<b><u>Posting Period in SAP ==> Posting period In ORACLE</b></u></u></b>
Most of the terms are finance terms , so they are common ( eg. an account number is an account number in ORACLE and SAP ) between two systems. I am interested in any specific thing that is available in ORACLE but not in SAP and vice verse.
thanks for the link you have provided.
Its very useful. -
Configuration steps between PS and FICO
Dear All ,
Pl anybody tell me , how to create a link between PS and FI , kindly write the configuration steps releated PS and FI integration .
Thanks in AdvanceAmit
This thread is now locked. Your question has already been answered - see thread
PS integration with other modules
Muzamil - thanks for your comment. -
Is it possible to use Facetime between Mac and iPad with the same Apple ID?
Hello,
I have a MacBook Pro and an iPad. May MacBook is used by my wife and me at home. I take the Pad with me when I travel. On the MacBook I have and Apple ID registered. It is the same I use with the iPad. Do I need a differnt ID for my wife if we want to use Facetime? Or do I need to create a seperate user-profile for my wife on the MacBook?
Thanks for your feedback in advance.Hi
I use the same apple id for the same thing when i travel between myself and people at home over my iphone and the ipad i leave at home always seems to work of for me
I normally just give it a little test before i leave each time by signing in of both devices and trying ringing myself
Hope this helps -
How to configure link between 2921 and SM-D-ES3G-48-P EtherSwitch Service Module
hi,
I can't do that like the procedure given by Cisco.
http://www.cisco.com/en/US/partner/docs/routers/access/interfaces/software/feature/guide/eesm_sw.html#wp1942894
Cisco Procedure :
interface gi10/0
ip address x.x.x.x x.x.x.x
service-module gigabitethernet 1/0 session
My result :
R2921-8CPITR-1(config)#int gi 1/1
R2921-8CPITR-1(config-if)#ip address 2.2.2.2 255.255.255.192
% IP addresses may not be configured on L2 links.
R2921-8CPITR-1(config-if)
R2921-8CPITR-1(config)#interface gigabitEthernet 1/1.1 ?
% Unrecognized command
R2921-8CPITR-1(config)#interface gigabitEthernet 1/1 ?
<cr>
R2921-8CPITR-1(config)#
the session is not possible also ?
R2921-8CPITR-1#service-module gigabitEthernet 1/1 sess
^
% Invalid input detected at '^' marker.
R2921-8CPITR-1#
The routeur said that it's not a L3 port, so how to configure it to allow communication between the 2921 and the card ?
Is there a bug with that version I'm in 15.1(4)M4 ????
R2921-8CPITR-1#sh ver
Cisco IOS Software, C2900 Software (C2900-UNIVERSALK9-M), Version 15.1(4)M4, RELEASE SOFTWARE (fc1)
Technical Support: http://www.cisco.com/techsupport
Copyright (c) 1986-2012 by Cisco Systems, Inc.
Compiled Tue 20-Mar-12 18:57 by prod_rel_team
ROM: System Bootstrap, Version 15.0(1r)M15, RELEASE SOFTWARE (fc1)
R2921-8CPITR-1 uptime is 19 hours, 21 minutes
System returned to ROM by power-on
System restarted at 16:00:45 GAB Fri Sep 14 2012
System image file is "flash0:c2900-universalk9-mz.SPA.151-4.M4.bin"
Last reload type: Normal Reload
This product contains cryptographic features and is subject to United
States and local country laws governing import, export, transfer and
use. Delivery of Cisco cryptographic products does not imply
third-party authority to import, export, distribute or use encryption.
Importers, exporters, distributors and users are responsible for
compliance with U.S. and local country laws. By using this product you
agree to comply with applicable laws and regulations. If you are unable
to comply with U.S. and local laws, return this product immediately.
A summary of U.S. laws governing Cisco cryptographic products may be found at:
http://www.cisco.com/wwl/export/crypto/tool/stqrg.html
If you require further assistance please contact us by sending email to
[email protected].
Cisco CISCO2921/K9 (revision 1.0) with 479232K/45056K bytes of memory.
Processor board ID FGL1618119E
6 Gigabit Ethernet interfaces
2 terminal lines
DRAM configuration is 64 bits wide with parity enabled.
255K bytes of non-volatile configuration memory.
250880K bytes of ATA System CompactFlash 0 (Read/Write)
License Info:
License UDI:
Device# PID SN
*0 CISCO2921/K9 FGL1618119E
Technology Package License Information for Module:'c2900'
Technology Technology-package Technology-package
Current Type Next reboot
ipbase ipbasek9 Permanent ipbasek9
security None None None
uc None None None
data None None None
Configuration register is 0x2102
R2921-8CPITR-1#Same issue here.
I just waited a few minutes and the interface went down and back up, this time it was a L3 interface.
My guess is that it was booting the switch module IOS, and it detected it until it was fully booted:
Apr 11 05:26:52.091: %LINK-3-UPDOWN: Interface GigabitEthernet0/0, changed state to down
Apr 11 05:26:52.091: %LINK-3-UPDOWN: Interface GigabitEthernet0/1, changed state to down
Apr 11 05:26:52.091: %LINK-3-UPDOWN: Interface GigabitEthernet0/2, changed state to down
Apr 11 05:26:52.091: %LINK-3-UPDOWN: Interface GigabitEthernet1/0, changed state to up
Apr 11 05:26:52.795: %LINEPROTO-5-UPDOWN: Line protocol on Interface Vlan1, changed state to down
Apr 11 05:26:53.091: %LINEPROTO-5-UPDOWN: Line protocol on Interface GigabitEthernet0/0, changed state to down
Apr 11 05:26:53.091: %LINEPROTO-5-UPDOWN: Line protocol on Interface GigabitEthernet0/1, changed state to down
Apr 11 05:26:53.091: %LINEPROTO-5-UPDOWN: Line protocol on Interface GigabitEthernet0/2, changed state to down
Apr 11 05:26:53.091: %LINEPROTO-5-UPDOWN: Line protocol on Interface GigabitEthernet1/0, changed state to up
Apr 11 05:27:46.895: %LINK-5-CHANGED: Interface Embedded-Service-Engine0/0, changed state to administratively down
Apr 11 05:27:46.895: %LINK-5-CHANGED: Interface GigabitEthernet0/0, changed state to administratively down
Apr 11 05:27:46.947: %LINK-5-CHANGED: Interface GigabitEthernet0/1, changed state to administratively down
Apr 11 05:27:47.031: %LINK-5-CHANGED: Interface GigabitEthernet0/2, changed state to administratively down
Apr 11 05:27:47.083: %LINK-5-CHANGED: Interface GigabitEthernet1/0, changed state to administratively down
Apr 11 05:27:47.895: %LINEPROTO-5-UPDOWN: Line protocol on Interface Embedded-Service-Engine0/0, changed state to down
Apr 11 05:27:48.083: %LINEPROTO-5-UPDOWN: Line protocol on Interface GigabitEthernet1/0, changed state to down
Apr 11 05:27:49.283: %IP-5-WEBINST_KILL: Terminating DNS process
Apr 11 05:27:52.499: %LINK-3-UPDOWN: Interface GigabitEthernet1/1, changed state to up
Apr 11 05:27:53.087: %SYS-5-RESTART: System restarted --
Cisco IOS Software, C2951 Software (C2951-UNIVERSALK9-M), Version 15.1(4)M5, RELEASE SOFTWARE (fc1)
Technical Support: http://www.cisco.com/techsupport
Copyright (c) 1986-2012 by Cisco Systems, Inc.
Compiled Tue 04-Sep-12 16:50 by prod_rel_team
Apr 11 05:27:53.255: %SNMP-5-COLDSTART: SNMP agent on host Router is undergoing a cold start
Apr 11 05:27:53.499: %LINEPROTO-5-UPDOWN: Line protocol on Interface GigabitEthernet1/1, changed state to up
Apr 11 05:28:21.435: %LINEPROTO-5-UPDOWN: Line protocol on Interface Vlan1, changed state to up
Apr 11 05:29:22.091: %LINEPROTO-5-UPDOWN: Line protocol on Interface GigabitEthernet1/1, changed state to down
Apr 11 05:29:22.095: %LINEPROTO-5-UPDOWN: Line protocol on Interface Vlan1, changed state to down
Router>en
Router#sh ip int brief
Interface IP-Address OK? Method Status Protocol
Embedded-Service-Engine0/0 unassigned YES unset administratively down down
GigabitEthernet0/0 unassigned YES unset administratively down down
GigabitEthernet0/1 unassigned YES unset administratively down down
GigabitEthernet0/2 unassigned YES unset administratively down down
GigabitEthernet1/0 unassigned YES unset administratively down down
GigabitEthernet1/1 unassigned YES unset up down
Vlan1 unassigned YES unset down down
Router#
Apr 11 05:29:46.106: %LINEPROTO-5-UPDOWN: Line protocol on Interface GigabitEthernet1/1, changed state to upconf t
Enter configuration commands, one per line. End with CNTL/Z.
Router(config)#int g1/0
Router(config-if)#ip add 1.1.1.1 255.255.255.0
Router(config-if)#no shut
Router(config-if)#
Apr 11 05:30:09.046: %LINK-3-UPDOWN: Interface GigabitEthernet1/0, changed state to up
Apr 11 05:30:10.046: %LINEPROTO-5-UPDOWN: Line protocol on Interface GigabitEthernet1/0, changed state to up
Router(config-if)#end -
VPC between server and nexus switches
Hi all,
I would like to ask following question:
We are using virtual portchannels to connect e.g. ESXi-Servers with trunks on two Nexus switches. When the switch "rz2sw1" has gone faulty, we expect that the trunk connections between switch rz2sw2 would still work. That's the reason why they are built. But they didn't as you can see in the screenshot (attaced) former mail.
Do you know what can be problem.. thank youIt appears that the peer-link was down. If the peer-link is down and the keep-alive is still up, the secondary device will shutdown all of it's VPC links to ensure dual active (split brain) is avoided.
On a Nexus 7000, its recommended to use a front panel (data port) for the keep-alive instead of the management port. My assumption would be that you are using the MGMT0 for keep-alive and all front panel ports went off-line. If you use a front panel port for keep-alive and all line cards go off line on the primary, the secondary will take over as expected. -
Configuration/relationship between PermSize and HeapMemory
Is there any recomended relationship between PermSize memory and Heap Memory?
I'm having a few "java.lang.OutOfMemoryError: PermGen space. I'm using tomcat 5.5 and jre 1.5 with 64 bits and debian lenny. The heap memory is 16-24 Gb.
What -XX:MaxPermSize should I use?poroto20 wrote:
Is there any recommended relationship between PermSize memory and Heap Memory?No
I'm having a few "java.lang.OutOfMemoryError: PermGen space.
I'm using tomcat 5.5 and jre 1.5 with 64 bits and debian lenny.
The heap memory is 16-24 Gb.
What -XX:MaxPermSize should I use?The default is only 64m or possibly 30% larger.
If you have enough memory just go with MaxPermSize=1G, then monitor the usage with something like visualgc (part of jvmstat). -
Trunk configuration (VTP) between 3750 and 2811
Hi,
I have a stack of 6 Cisco Catalyst 3750G with 6 VLANs acting as a VTP server and want to establish a trunk link to my Cisco 2811 router equiped with a switching module 16 ports. Can I set the 2811 as a VTP client to propagate the VLAN info from the 3750 and configure one of the port on the switching module of the 2811 as a trunk encapsulated DOT1q and will I be able to route to the outside world.
Thank youI beleive the switching cards support vtp and that should be possible.
Table 2. Features Supported on Cisco EtherSwitch Modules
EtherSwitch Network Modules (NM-16ESW and NMD-36ESW)
EtherSwitch HWICs (HWIC-4ESW and HWICD-9ESW)
EtherSwitch Service Modules (NME-16ES-1G, NME-16ES-1G-P, NME-X-23ES-1G, NME-X-23ES-1G-P, NME-XD-48ES-2S-P, and NME-XD-24ES-1S-P)
VLANs
Multiple VLANs per Switch
Yes (varies by chassis; maximum of 64 on Cisco 3845)
Yes (maximum of 15 on any chassis)
Yes (maximum of 1,024 per switch or stack)
VLANs in 4,000 Range
No
No
Yes
IEEE 802.1Q Tagged and Untagged VLANs
Yes
Yes
Yes (802.1Q and Inter-Switch Link [ISL])
VLAN Trunking Protocol (VTP) Support for Client, Server, and Transparent Modes
Yes
Yes
Yes -
Is it possible to move content between private and public sites after publishing the latter?
Hi. Is anyone else in this position? My institution kept its original iTunes U site after migrating our public content to the new public site last year. We now have separate public and private (university log-in only) sites and must maintain both. The Public Site Administrator allowed the copying of existing content from the original iTunes U site to the new public site, but ONLY prior to publication of the public site. I have two related questions for the community:
1) How is it possible to maintain a workflow in which faculty create a course for the private iTunes U site (wanting to keep the content restricted to our students while the course is live), but then move the content over to the public site once the semester ends?
2) With the new app for Courses and the Course Manager on the public site, what do we do with the courses already created by faculty as Collections (either in the public or private sites)?
I hope there are folks out there that can help.
Thanks!
KevinI'd like to see a discussion on this exact topic as well. Have you determined yet how to move a private course (apple hosted) to the public site? Can you use an RSS feed from the private?
joe -
About configuration replicate between r3 and crm
hi gurus, i want to ask you a basic question, is the situation described right:
1, some configuration should be done in r3 and should be transfered to crm;
2, some can be done in crm and should be transfered to r3;
3, some should be done in both crm and r3, but can only do it seperately and manully;
4, some can be done in just r3 or crm and need not be transfered to the other one.
and one further question is how can i know the configuration in r3 should or can be tranfered to crm? i mean, i know there is a tcode to do the transfer, but how can i identify the item is the item i should transfer?
i am not a crm consultant, the question is perhaps not to the point. but really hope you gurus give some help.
thank you.Hi Daniel,
Let me try to answer your questions
1, some configuration should be done in r3 and should be transfered to crm;
Yes, for example pricing conditions
2, some can be done in crm and should be transfered to r3;
No, I dont think we transfer config from CRM to R/3.
3, some should be done in both crm and r3, but can only do it seperately and manully;
Yes
4, some can be done in just r3 or crm and need not be transfered to the other one
Yes
There are middleware objects which are used to download the R/3 config to CRM.I dont think there is a standard way to find out which config needs to be downloaded.
Regards,
Madhu
Maybe you are looking for
-
Can I set up 2 apple tv on the same network and iTunes account, and choose which apple tv I want to AirPlay to from my iPod 4g? or does only one apple tv, show up on the AirPlay list when you hit the AirPlay button ? I have one apple tv In
-
IPod disconnected error message
So I have been receiving this error message whenever I try to sync my iPod. I have attempted using different cords (legit Apple cords), different USB ports, rebooting my computer, and others that I cannot recall at the moment. It appears as though
-
How to configure the following scenario?
I have a following requirement: I am selling an equipment to a customer and the delivery has taken place in Jan 2008. However as per the requirement I can recognize the revenue only in after installation which will be in March 2008. However I will be
-
Email BPC data manager Package log to a team for BPC10 NW
Hi iI found documentation on how to send Data manager package by email. Contained 2 transports but the documentation is for 7.0 NW do you know if they have a documentation for BPC 10 NW ?
-
RFC / FM to upload images to Production system
Hi Everyone, I want to change my logo on my SAP Easy access..but I don't want to open my production system. Is there any RFC / FM to upload the logo ? Thank you!