Is it possible to connect a GS70 to a 144HZ monitor to get that refresh rate?

Hi guys, So I'm planning to get an 144hz monitor from Asus. I will use a mini DP to DP cable in order to connect from the laptop to the monitor (I'm using MSI GS70 with a GTX 860m card). ...

Quote from: bwfc0907 on 01-August-15, 14:05:31This activated on upgrade so it doesn't make sense why a clean install should not activate.
How did you do the clean install? Power on laptop and boot from Win10 m...

Similar Messages

  • Clients Connect to N AP's on 5508 and get different Transfer rates than on 4404

    I have have 2x 4404's (2x) and 2x 5508's all are running 7.0.240.0. When I take an 1142 and associate it to a 4404 I can connect a test client using N at 144Mbps and I can get transfer rates averaging 70Mbps (using iperf tests). When I take the same AP and associate it to a 5508, (same SSID, etc) I connect at 144Mbps but only get average 6Mbps transfer rates. I get the same results with 1252's. I get the same results if I wipe the config on the 5508 and start from scratch. It only happens when connecting at a/n, when I use a b/g AP such as 1132 I connect at 54Mbps on either controller and get transfer rates of 24Mbps. I have enabled disabled LAG (rebooted), moved the 5508 to connect to the same swtich ports, swapped GBICs. The issue happens on both 5508s, TAC has been unable to resolve this and they are confused as well.
    Some of the other things I have tried:
    •-          You are facing the issue on 5508's WLC only.
    •-          Both the WLC and the client reports high connection speed “144Mbps”
    •-          iPerf between wireless and wired showed the following:
    on 4400:  [124]  0.0-16.9 sec   154 MBytes  76.5 Mbits/sec
    On 5500:  [124]  0.0-94.3 sec  70.2 MBytes  6.25 Mbits/sec
    •-          The AP is the same AP, you just bounce it from 1 WLC to another.
    •-          The location of the AP is the same in all the tests, but it can be replicated with an 1142 anywhere on site and get the same results.
    •-          The test PC is the same in both cases
    •-          The configuration is the same on both WLC’s confirmed visaully in GUI and via CLI outputs and compaired.
    •-          The switch is the same, but have tired swapping 4404 and 5508 in data center.
    •-          Tried to swap the GBICs.
    •-          Used different ports on the 5508 (not just diff GBICs)
    •-          Disabled the LAG to rule out the load balancing algorithm.
    •-       Replaced the patch cables
    Used same ip space that the 4404 is using without sucess.
    Upgraded my second 5508 to version 7.5 and exact same resutls.
    Any ideas?

    Hi 
    In my 5508 WLC i have exactly the same problem as you  gsutherland 
    I tried apply this command config 802.11b 11nSupport a-mpdu tx priority all disable
    and i get message 
    "802.11b network not disabled"
    Why i must turn off b standard ?
    Thanks for respons 

  • Is it possible to connect an external USB 2.0 hard drive to a Thunderbolt Display?

    Hello,
    Is it possible to connect an external USB 2.0 hard drive to a Thunderbolt Display and back up a MacBook Air to the external hard drive using Time Machine?
    I intend to connect my MacBook Air to the Thunderbolt Display using a Thunderbolt cable.
    I would also like to connect my printer via USB 2.0 to the Thunderbolt Display. Will this also work?
    Effectively using the Thunderbolt Display as a USB hub or docking station.
    Regards,
    Ben

    Ok, thanks.
    My 1 cable to ThunderBolt Display objective
    MacBook Air -> (via 1 x Thunderbolt cable) -> Thunderbolt Display -> (via 1 x USB cable) -> USB 2.0 external hard drive
    I would like to know if this configuration is possible and Time Machine will run correctly.
    Your 2 cable suggestion (I think)
    MacBook Air -> (via 1 x Thunderbolt cable + 1 x USB cable) -> Thunderbolt Display + USB 2.0 external hard drive
    This configuration requires 2 cables to disconnect/reconnect from my MacBook Air.

  • Is this possible: SNC connection from SAP GUI to SAP Router, and ...

    Hi,
    I have (stupid perhaps) question.
    Is this scenario possible:
    SNC connection from SAP GUI to SAP Router, and non-SNC connection from SAP Router to SAP System.
    I know how to set up scenario like this:
    SAP System --- (non-SNC conn) --- saprouter1 --- (SNC conn) --- saprouter2 --- (non-SNC conn) --- SAP GUI.
    Best regards,
    Marek Majchrowski

    Wolfgang,
    To be sure myself and Marek understand, can you confirm the different scenarios supported:
    Scenario 1:
    SAP GUI --- (non SNC conn) --- saprouter1 --- (SNC conn) --- saprouter2 --- (non-SNC conn) --- SAP System
    With this scenario, it would be possible for a user to logon using SAP GUI onto the SAP System, but without SAP GUI SNC.
    Scenario 2:
    SAP GUI --- (SNC conn) --- saprouter1 --- (non SNC conn) --- saprouter2 --- (SNC conn) --- SAP System
    With this scenario it would be possible to logon to the SAP System using SAP GUI, and using SNC authentication.
    Also, with this scenario the SAP GUI software and SAP System software would consider this to be similar to:
    SAP GUI -- (SNC conn) -- SAP System
    Scenario 3:
    This is the scenario mentioned by Marek in his initial question:
    SAP GUI -- (SNC conn) -- saprouter1 -- (non SNC conn) -- SAP System
    With this scenario it will not be possible to logon to SAP System using SNC, and only possible if the SAP GUI is configured to not use SNC. In other words the SNC connection between SAP GUI and saprouter1 is available, but cannot be used.
    Thanks,
    Tim
    Edited by: Tim Alsop on Feb 25, 2008 5:24 PM

  • Is it possible to connect my mid 2010 Macbook Pro with my 21.5" iMac 11,2 so that I can work with dual screens?

    Is it possible to connect my mid 2010 Macbook Pro with my 21.5" iMac 11,2 so that I can work with dual screens?

    try xxx - may work
    _may_ work.

  • Business Contact Manager 2010 - is it possible to connect a Contact with multiple Accounts

    Hi, I'm proficient with Outlook but new to BCM. Currently setting things up but have some Contacts who own more than one company or are on another companies Board etc.  
    My questions is - Is it possible to connect a Contact to more than one Account?
    Many thanks

    Hi,
    Currently it's not possible. The workaround may be to duplicate the contact in Business Contacts to make that happen.
    Regards,
    Melon Chen
    TechNet Community Support

  • My TV is mounted on a wall so I can't connect the Apple TV device. Is it possible to connect to an HD Cable Box and send signal to TV that way? Other problem is that Box only has one HDMI socket .. Help!

    My TV is mounted on a wall so I can't connect the Apple TV device. Is it possible to connect to an HD Cable Box and send signal to TV that way? Other problem is that Box only has one HDMI socket so would also have to use a splitter. Tried Apple Support but couldn't offer a solution. I can't be the only person with this issue surely?
    Help!

    No, unless you are using a home theatre system already, your only option is to connect to the TV.

  • My Apple Macbook Pro is connected by Telstra wireless Broadband to the Internet. Is it possible to connect to a WiFi Printer using Air Express or some other system? to the Internet.

    Hi
    Can someone please advise if it is possible to connect my Apple MacBook Pro 13.3" to a WiFi Printer, as I am connected to the Internet through Telstra Wireless broadband.
    Is it possible by using Airport Express or some other way?
    Thanks

    1.Power Cycle
       Power off the router. Unplug it from the wall. Wait a while.
       Plug it back to the wall. Power the router on. Wait until all the lights are lit properly.
       It will take a while.
      Restart the computer.
      Start up in Safe Mode.
       http://support.apple.com/kb/PH11212?viewlocale=en_US
    2.  Turn off Extensions, if any.
         Safari > Preferences > Extensions
    3. Turn off proxies, if selected.
         System Preference > Network > Advanced  > Proxies Tab
         Under "Select Protocol", uncheck any box if selected.
         Click "OK" then  "Apply"
    4. Uninstall anti-virus software, if any.
    A new Mac comes with 90 days of free tech support from AppleCare.
    AppleCare: 1-800-275-2273

  • Is it possible to connect R/3 4.7 (a.k.a Enterprise) and BI7.0/SEM-BCS6.0?

    Hi,
    Does anyone have some experience or knowledge on this question;
    is it possible to connect R/3 4.7 (a.k.a Enterprise) and BI7.0/SEM-BCS6.0?
    If yes, what is required for R/3 insatallation?
    For example, SP updating on PI_BASIS, SAP-BW or so.
    regards,
    Katsumi

    Hi, greg
    Thanks for your experiential reply.
    > it's a pain to rerun iterations with such an interface, though.
    I want to know some more, if it colud be.
    And, I'm still afraid of interactivity between R/3 4.7 and SEM-BCS 6.0.
    Is there anything required for R/3 insatallation?
    regards,
    Katsumi

  • Is it really possible to connect a iPod Nano to a itrip etc?

    I heard that it is possible to connect the nano to the iRiver aft-100 fm transmitter.
    I this true?
    have somebody tried it?
    if it works just fine, i will buy one!

    Any FM tranmitter will work with the nano as long as it doesn't require the headphone remote port which the nano doesn't have. The iTrip requires this port.

  • Is it possible to connect the iPad to an Infocus and a remote for ppt presentations at the same time?

    I've always used PC and I'm planning on making the transition to Mac.  That's why I'm considering buying an iPad. Today I went to Best Buys and the Mac guy told me that it isn't possible to connect the iPad to an Infocus and a remote for ppt presentations at the same time. Is that true?  I'm a speaker and that was the main reason I was considering buying an iPad, so I didn't have to carry my laptop. Thanks for your help!

    Thanks for your reply. Looks like it can as I have just found this https://www.youtube.com/watch?v=nKp02y4JXVs

  • Is it possible to connect a mac book pro via thunderbolt and a dvi switchbox (multiple computers) to a thunderbolt display?

    Hi,
    I'm planning to buy a thunderbolt display.Since I have not only apple computers with a thunderbolt port I wonder if it's possible to connect my mac book pro via thunderbolt and a DVI switchbox via a "mini displayport to DVI connector" to the thunderbolt display at the same time. Thunderbolt is a bus architecture. Thus there must be an ingoing and an outgoing port on the display. The rearview of the display I've seen so far don't show this:
    If this is not possible then I must question the market chances of this product. Seems as if the product marketing guys exaggerated the launch of the thunderbolt technology.
    -ais-swiss

    ais-swiss wrote:
    How to connect windows laptop (vga) to thunderbolt display?
    AHHH??!!!!!!  Was that your original question??   I assumed you were trying to output FROM your computer (MacBook Pro w/ Thunderbolt) to the new display and then OUT to be the video source to a DVI switcher.
    MB Pro w/TB ---> TB Display ---> mDP-to-DVI adapter ---> DVI switcher
    So it seems as if it's not possible to use the thunderbolt display with the mini display port adapter to DVI you've mentioned.
    I did not understand that you were trying to use other PC's into a switcher and then THAT Video source to connect INTO the TB display.   If THAT is what you're trying to do, then NO....  You can NOT use the new TB Display to be used to display "FROM" a DVI switcher (and also can NOT be used to display from other Non-TB-Apple computers).
    I've also called apple. The statement was that one needs a computer with osx 10.6.x in order to connect the thunderbolt display. That makes it impossible to hook a windows pc or older mac to the new and shiny thunderbolt display.
    I wonder why apple doesn't state this in their technical descriptions...?
    -ais-swiss
    Actually, the state that information all over the Tech Specs on the Apple Store website.
    http://store.apple.com/us/product/MC914LL/A?mco=MTY3ODQ5OTY
    Here are two different statements from that webpage:
    So yes.... other NON-Apple PC's (or non-TB devices) do Not have the Thunderbolt technology (hardware/software) to be able to communicate with the TB display or other TB devices.

  • Is it possible to connect an HP LaserJet P4015n printer to a computer via the ethernet ports?

    My usb port on my Laserjet P4015n no longer works and I am unable to connect this printer to my network router because it's in a different room. Is it possible to connect an HP LaserJet P4015n printer to a computer via the ethernet ports? Of so, how would I go about making this connection? Will I need to install ethernet drivers for this to work?
    Thanks,
    Greg

    This seems to be a commercial product. For the best chance at finding a solution I would suggest posting in the forum for HP Business Support!
    You can find the Commercial Laserjet board here:
    http://h30499.www3.hp.com/t5/Printers-LaserJet/bd-p/bsc-413
    Best of Luck!
    You can say thanks by clicking the Kudos Star in my post. If my post resolves your problem, please mark it as Accepted Solution so others can benefit too.

  • Is it possible to connect 2 Samsung monitors to an imac 27"

    Is it possible to connect 2 Samsung monitors with a resolution of 1920x1080 to a new imac 27" with two thunderbolt connectors (per mini displayport to dvi or mdp to hdmi cable)? So that there is the full resolution on all three (Mac + two Samsung) monitors? And if its possible what do I need to do so?
    Thanks for the help

    I have no ThunderBolt iMac (mine is a 2009) nor one or two of these Samsung Displays.
    So I can't say or guarantee that the combination will work.
    Some displays simply don't work with Macs for no apparent reason.
    Best would be to take your MacBook Pro into the store where you want to buy the Samsung displays and ask for a test.
    Stefan

  • Is it possible to connect a 2011, 13' MacBook to 2 external displays?

    Is it possible to connect 2 external monitors to a Mac Book 2011 (has Thunderbolt port).
    I was using a Matrox Dual Head 2 Go DP Edition adaptor but it crashed after installing Yosemite 10.10
    Is there another work around available?

    Correct me if i'm wrong, but that hub would not do the job either. Sure it has two thunderbolt ports, but one of them is connected to your Mac and the other one is daisy chaining to your thunderbolt device. So you would only have one thunderbolt port free for a monitor (using a displayport adapter).
    AFAIK you would need to have a thunderbolt display to daisy chain with the chain ending as soon as you put on a display port adapter. That or you buy some sort of usb device (like this), however I have no idea how well they perform.

Maybe you are looking for

  • Help in loop and at new

    Hallow I have a program that call to smart form. The user have to put course number and employee number and  the program check if the student pass the course send sf and if don’t  send other sf .my problem is when the user put just course number in,

  • Crystal Reports Web Services

    I am brand new to Crystal Reports.  I am actually only using a demo version to see if it can do what i want it to.  I have a web based database software that i am using.  The reporting functionality with this software is very limited.  I wanted to "c

  • Can't get a text field to atuo populate based upon a dropdown selection

    I have a drop down box with 3 values that can be selected: Dropdown2 = 101-3 subd.A                       101-3 subd.B                       101-3 subd.C I am trying to get a text field to auto populate based upon the selection: if Dropdown2 = 101-3

  • All pictures become '?' (a blue question symbol) in the emails...

    Hi: These days I noticed that all the pictures in any of my email, shown as a blue question symbol and I can not preview it , or select on it, or save/copy it. But last week sometime I remember everything was working fine. I did nothing to my iPhone.

  • Images Shuffled Randomly in iMovie Media Browser?

    When creating an imovie slide show and opening my AP3 projects in the media browser the images are not in the same sequence as when I view them in AP3. Can this be corrected? I've posted this ? in iMovie forum as well.