Is it possible to debug step by step for share point designer workflow in share point 2010

Hi all,<o:p></o:p>
I have created a reminder date work flow but it is not working .In this work flow it need to be check first its status if its status is suspend then only workflow can run .I am
attaching below workflow logic check if any modifications needed please suggest me . And I have doubt is it possible to check step by step debugging like in coding we are using break point in this way any break point is available for designer workflows
? If break point is available please guide me how to get and use those<o:p></o:p>
Thanking you,<o:p></o:p>
ArunDarly
<o:p>Workflow logic given below</o:p>

You can't step through a SharePoint Designer Workflow. The normal workaround is to Log messages to the History list with the values you want to look at where you would normally put breakpoints. Then run the workflow and examine the history
list to see how the values changed as you went through your workflow.
Paul Stork SharePoint Server MVP
Principal Architect: Blue Chip Consulting Group
Blog: http://dontpapanic.com/blog
Twitter: Follow @pstork
Please remember to mark your question as "answered" if this solves your problem.

Similar Messages

Steps for loading approvers, solicitors & workflows to the CUP

Hello,
I want to know if there is a way or steps to load the approvers, solicitors & workflows in the CUP of SAP GRC AC 5.3.
What I mean is that can I load first the workflows and then the approvers & solicitors and then join the approvers to the workflow, or do I have to put first the approvers & solicitors first and then the workflows & join them??
Please I need help.
Best regards...
Pablo Mortera.

Sorry, Pablo. Just one question::
What do you mean by solicitors?
Having approvers set up and creating workflows are two separate tasks and have no dependency so you don't have to worry about the order. You won't be able to create request without having both of them configured in CUP.
Regards,
Alpesh

Is it possible to debug a LV progr. for an NI-6602 in simulation mode?

Is it possible to use the DAQmx Create Channel(CI-Count Edges).vi without actually having the PXI-6602 hardware installed in my PC, i.e. use a simulation driver?

Yes, you can simulate that device through Measurement &
Automation Explorer (MAX).
Select NI-DAQmx Simulated Device by right-clicking on NI-DAQmx
Devices >> Create new NI-DAQmx Device.
A new window will be displayed and you can select the PXI-6602 through
the TIO Series (Counter Timer) category.
All of the data will be meaningless. Simulated devices are used to help develop
software without physically having the hardware.
Respectfully,
Rob F
Test Engineer
Condition Measurements
National Instruments

Development Steps for addon after design the screen in screen painter

Dear All,
I am new to SDK Development.Now am developing an screen for Sub contracting.Basically am not a B1 technical conultant but I have some knowledge in development. i was developed a screen in screen painter but i dont know how to intergrate and develop the coding in VS2005.
Regards,
Vijay

Hi
There are many samples in SDK folder in C driveProgram filesSAPSAp business one SDKSamples
Have a look at them they will give you a good start..
Thanks

Is it possible to debug workflows deployed using Workflow Manager in VS 2013?

I know and I have debugged workflows in VS 2012 as described here: http://msdn.microsoft.com/en-us/library/jj658563%28v=azure.10%29.aspx
But I am unable to debug in VS 2013 Update 2.
Also, many activities like HttpSend are not displaying after updating to VS 2013 Update 2.
Is there any fix available for this?

You can't step through a SharePoint Designer Workflow. The normal workaround is to Log messages to the History list with the values you want to look at where you would normally put breakpoints. Then run the workflow and examine the history
list to see how the values changed as you went through your workflow.
Paul Stork SharePoint Server MVP
Principal Architect: Blue Chip Consulting Group
Blog: http://dontpapanic.com/blog
Twitter: Follow @pstork
Please remember to mark your question as "answered" if this solves your problem.

Steps for Getting Repository Reports to Work in SCM 9024

Have installed Des9i/SCM 9024. With this install, repository reports are not installed without the base release of O9iDS R2. What are the exact steps for getting the Designer Repository Reports to work via the RON in SCM 9024? Basically, I would like to have the Repository Reports option 'enabled' in the RON.
Does 9iDS 902 have to be installed in an Oracle Home first, and then install SCM into the same OH? I would rather not have to install the entire iDS just to be able to have object reporting in SCM.
-- Al

Hello Joe Matheis. Welcome to the Apple Discussions!
Let's double-check your AirPort's configuration for streaming iTunes ...
Either connect to the AX's wireless network or temporarily connect directly, using an Ethernet cable, to the Ethernet port of the AX, and then using the AirPort Utility in "Manual Setup" mode, make the following changes:
AirPort > Wireless
o Wireless Mode: Join a wireless network
o Network Name: <existing wireless network's name or SSID>
o Wireless Security: <select the encryption type of the existing wireless network>
o Wireless Password: <enter the existing wireless network password>
o Verify Password: <re-enter the existing wireless network password>
Music
o Enable AirTunes (checked)
o iTunes Speaker Name: <enter desired speaker name>
o iTunes Speaker Password: (optional)
o Verify Password: (optional)
o Click Update to write the new settings to the AX

Steps for debugging the ABAP program

Hi
Im a SAP-BW Consultant. I have a program in R/3-Side. I want to debugg that program.
Please give me the steps for debugging that program .
Kumar

Hi Ravi,
Check this link
http://help.sap.com/saphelp_nw2004s/helpdata/en/b3/d322540c3beb4ba53795784eebb680/content.htm
I give you some usefull Tips.
Type /h in command Bar.
Then press F8 then system will automatically goes to debugging mode.
Then press F5. Then it shows the Each and every line of your program.
or type break-point in your SE38 program. Then press F8. it will goes to the Debugging mode.
Thanks.
Reward If Helpful.
Message was edited by:
Viji

TA38633 is it possible to avoid having to do a "restore" entirely ? Also if i have to do a restore, i have windows 7- do i follow the steps for Windows XP?

Regarding error 1601 - is it possible to avoid having to do a "restore" entirely ?
Also if i have to do a restore, i have windows 7- do i follow the steps for Windows XP?
Many thanks

I'd refer to this
http://support.apple.com/kb/TS3694 (talks about security software and this error)
and this
http://support.apple.com/kb/HT1414
I've had Windows 7 for a while, but it seems the steps in iTunes are identical.

Eclipse - debug step is not synchronise with source code.

Hi,
I have an web application witch run on tomcat, when Idebug the application, the debug steps are not synchronize with the source code. Same thing when I change the code , after making the jar file and putting it in the WEB-INF/lib of the web application, the modifications didn't take place. It seem that the old code always remains. I looked at the compile class in the jar file and the modifications have been taken in to account.
what can cause this kind of behavior ? I relaunch tomcat many times without succes ?
any help ? thanks a lot.

Can it be the case that you compile your JAR optimized, i.e. without debug information? Then your classes are also without debug information.
This sounds very likely as a refresh problem. Be sure that both source files in Eclipse and class files in Tomcat have the same version (e.g. with simple system.out).

Is it possible to micro step using the Pci7314 (open loop) controller and umi7764 and Labview.

Is it possible to micro step using the Pci7314 (open loop) controller, umi7764 and Labview. if so how would this be set up. i have searched the valuemotion vi libraries and found no microstepping functions. Please could you offer any advice. cheers JON ROGERS

Hi Jon,
Micro-stepping is a property of the motor amplifier (motor drive) rather than the controller. It sounds like you are using a 3rd party drive, since you have a UMI. You want to check with your motor amplifier documentation to see if it's supported. Usually, there will be dip-switches on the drive that sets the microstep factor.
Hope this helps. Please let me know if you have any questions.
Thanks,
Ken Sun
Applications Engineering
National Instruments

Is it possible to create an inbound delivery for STO in a 2 step process ?

Hi Experts,
Is it possible to create an inbound delivery for STO in general (how do I get a vendor for a Plant. I have already assigned a plant to my vendor in vendor master - additional purchasing data, but it does not seem to work).
In particular if I want to create an inbound delivery in intra-company plant STO scenario, how do i do it?
Let me know in case if that is not possible.
Thanks,
Nitin

Hi Tao,
I did that also, but it did not work.
Finally I had to debug, and found that the for the document type UB (intra-company transfer) i should make the customizing setting which makes the vendor data to be considered. (Table T161).
Anyways, thanks for your help.
Regards,
Nitin

ECATT: Possible to debug inline ABAP?

Hello eCATT experts,
I have the following question:
is it possible to debug inline ABAP (between ABAP...ENDABAP) in the eCATT debugger?
When trying to step inside an ABAP...ENDABAP block with F5, I always end up after the ENDABAP statement.
Thanks and best regards,
Oliver

>
Oliver Thomas Niedermaier wrote:
> Hello eCATT experts,
>
> I have the following question:
> is it possible to debug inline ABAP (between ABAP...ENDABAP) in the eCATT debugger?
> When trying to step inside an ABAP...ENDABAP block with F5, I always end up after the ENDABAP statement.
>
> Thanks and best regards,
> Oliver
You can also break command.
ABAP.
BREAK USER_ID.
ENDABAP.
Where USER_ID is your user id in the SAP system.
This will help to stop the script for debugging only when you use it and it will continue executing for others without Stopping.
Hope this info helps.
Regards,
SSN.

Step by step for 2.6

So I think im finally ready to make the plundge to the 2.6 kernel.
So I need some help. Ive only compiled a kernel a few times, and I never changed many settings.
So could someone give a step by step for it (being sure to list any arch-specific quirks)? I would greatly appreciate it.
Also, I hear theres a patch that lets you run the Official Nvidia drivers with the 2.6 kerne, has anyone gone through this? I really have no idea how to go about doing this,as i've only ever installed the .run file.
Any help would be appreciated.
Also, its possible to switch between the 2.4 and 2.6 kernel, right? (obviously with a reboot).
Lastly, Is a new release of the 2.6 due out anytime soon? I dont want to download and compile this just to find a new version comes out.

You have to use module-init-tools which supercedes modutils. I made a PKGBUILD for it for my local system simply so I could uninstall it easier if I wanted. However, you still need the old modutils as well.
Here is my hack to get module-init-tools working:
1. Use the PKGBUILD below to compile and install module-init-tools.
2. For each of modprobe, lsmod, rmmod, depmod, and modinfo from modutils, rename those to modprobe.old, lsmod.old, etc. To find where these binaries are, use "pacman -Ql modutils".
3. Create symbolic links from the binaries that modutils used to provide to the new binaries that module-init-tools provides. Again, use "pacman -Ql module-init-tools" to figure out where the new ones are.
Example - modutils provides /sbin/lsmod. Rename that to /sbin/lsmod.old. module-init-tools provides /usr/bin/lsmod. Create a symbolic link as follows:
[root@limbo root]# ln -s /usr/bin/lsmod /sbin/lsmod
If you aren't 100% sure what i am trying to say here, don't try any of it, or you will bork your system. Also, this is more of a hack, and that's why I didn't upload the package to incoming. I only made the PKGBUILD to keep track of where everything was going.
Anyway... hope this helps you on your way to:
[john@limbo john]$ uname -r
2.6.0-test5
[john@limbo john]$
PKGBUILD
pkgname=module-init-tools
pkgver=0.9.13
pkgdesc=""
url="http://www.kernel.org/pub/linux/kernel/people/rusty/modules/"
depends=()
conflicts=()
backup=()
install=
source=(http://www.kernel.org/pub/linux/kernel/people/rusty/modules/$pkgname-$pkgver.tar.gz)
build() {
cd $startdir/src/$pkgname-$pkgver
./configure
make || return 1
make prefix=$startdir/pkg/usr install

What are the Major Step for Completely Avoiding the Server Problem?

Like Ora-01033,Ora-12514.

leen wrote:
Ora-12514 : is listener error you need to make sure is running up and no error in listener.log
any database error can be avoided by monitor your database everyday .
It's possible to check daily that listener is running properly. Please, Don't mind can you provide the steps.The steps for what? Checking your listener? Just try to make a connection that uses it. For example.
sqlplus scott/tiger@orclBut believe me, once your listener and clients are configured, the listener will 'just run' and NOT be a problem. I've been an Oracle DBA since 1995 and I've only seen ONE listener failure. And that was only when a friend at another company called to ask about a problem HE was having.

What are the basic steps for creating a content repository?

I am trying to create a document store on a file system (fsdb) that will hold files that are ftp's to that location. Is this possible using KM? If so, what are the basic steps for creating a file system repository and using it through KM? I have found stuff on help.sap.com but that only tells you what each component does not what actual steps need to be taken to setup KM, such as user rights , creating an entry point, so that all of KM is not visible, etc...
If anyone knows of any guides that show a step by step process that would be great too.
Thanks
Paul

Hi Paul
First of all you need to create a new repository
Suppose you want to add all the documents under folder Paul under C: Drive
(Even you can put whole documents of C: drive into Paul)
Navigate to System Admin -> System Configuration -> Knowledge management -> Content Management -> Repository Manager -> File System Repository
There you can create a new directory by clicking on button New
Give the parameters as follows :-
Name               :           Anything you like
Description       :           Anything you want
Prefix (must start with /) : Probably same as your repository name like \Paul
Lookup mode : caseless
Root Directory   : C:\Paul
NOTE: This is the trick. You need to give the proper path means folder path which you want use as repository)
Repository Services : Any services you want
Property Search : Managercom.sapportals.wcm.repository.manager.generic.search.SimplePropertySearchManager
Security Manager         :           AclSecurityManager
ACL Manager Cache   :           ca_cm_rep_acl
The save it
Now see whether the same repository is coming under KM Content or not, if not may be after restart it will come.
I think the above information will help you. If still you have problem, please feel free to contect me.
Regards,
Chamkaur

Is it possible to debug step by step for share point designer workflow in share point 2010

Similar Messages

Maybe you are looking for